Search Documents

By W. A. Riggs

In a single year the total transportation cost equals nearly 30 pct of the value of mineral commodities, the largest single cost from the deposit to consumer. The magnitude of this economic factor calls for more complete understanding of cost and operational problems between producer and carrier than now exists. Details are given of the costs of providing transportation as well as freight rates for selling transportation. In 1958, transportation of mineral commodities in the United States required 600 billion ton-miles to move 1 3/4 billion tons of products of mines comprising solid fuels, crude oil, industrial minerals and rocks, and ores. Possibly 17 pct was handled by more than one mode of transport, since combinations of several modes of transport may, at times, achieve better service/cost results than any single mode. Total transportation cost of nearly $5 billion equaled roughly 30 pct of the value of the mineral commodities, the largest single cost from the mineral deposit to the consumer. The tremendous magnitude of this transportation undertaking demands much more complete understanding than now exists between mineral producers and carriers about the economic and operational problems of each other. A substantial portion of the daily work of the writer is spent in trying to act as a combination interpreter and catalyst between potential shippers and carriers, hoping to direct both to points of mutual understanding and advantage. For the purpose of this paper, it is necessary to ask mining people to accept some terminology and to try to appreciate the mental approach of the freight rate making people of the carriers. This paper will consider costs of providing transportation as well as freight rates for selling transportation—although these are fields of limited certainty. There are no accurate statistical breakdowns for all modes of transport and types of carriers indicating commodities, volume of traffic, distances, costs, and rates. Much information is available for railroads, and some for the regulated portions of air, motor, pipeline, and water transportation. Unregulated carriers, handling about half of the transportation of products of mines, are not required to report, and very little is known of their activities. Figures used herein are national in scope, unless otherwise indicated, and have generally been derived from Interstate Commerce Commission reports and files. Tonnage figures have been reduced to net tons of 2000 lb. The very generalized comparison of average mileage freight rate levels for various modes of transport provided by Fig. 1 affords advantageous perspective for the entire field of transportation costs. Dashed guide lines show cents per ton-mile, and dotted guide lines show percentage of first class railroad freight rate. While costs of other than railroad transportation more nearly follow constant cents per ton-mile functions, costs of railroad transportation show characteristic taper, or decrease in cents per-ton mile with increasing length of haul. This fundamental difference in cost is due largely to the fact that railroads and pipelines provide their own fully taxed roadway facilities while highway, waterway, and air carriers use government-provided tax-free roadway at no cost other than fuel, license, and certain excise taxes. Thus railroad and pipeline transportation might be said to carry heavy threshold costs in addition to those transportation costs which are directly variable with ton miles of transportation produced. The original basis of railroad freight rate structures lies in the classification of all articles of commerce into railroad class ralings ranging from 7 to 40 pct of first class (100 pct) rate level, dependent on value, hazard, loading characteristics, service requirements, and whether carload or less than carload. Classification tables and mileage-based (but arbitrarily grouped), rate scales are published as tariffs subject to approval by regulatory bodies. Used together, these determine class rates in cents per 100 lb between points in the U. S. Where local commercial or operating conditions render it advantageous for carriers to depart from

Jan 1, 1961

By Granville S. Borden, Frank H. Madison

The fruits of industry are divided between capital, labor, and governments. Capital takes its redemption and remuneration through profits or dividends; labor takes its share through wages; governments take their share through taxes. Each must have a just share, and the question of what is a just share and the question of who shall make the allocation are vital current political and economic issues. Certain political philosophies con- tend that government should take all the fruits and that some dictator or politician should have irrevocable discretion and power to distribute the fruits. Believers in democracy and free enterprise adhere to the view that capital is entitled to redemption and fair remuneration; that labor shall have a fair wage; and that governments shall make equitable levies. But since all human beings, both individually and in groups, are inherently selfish, there are many variable views in regard to the question of what ratios shall be applied in a division of the fruits and who shall have the power to fix these ratios. Perhaps all parties should devote more energy to means of increasing the crop, and not so much time to quarreling over a division of the existing crop. Moreover, all three parties must guard against killing the goose that lays the mineral eggs. For example, if the tax burden becomes oppressive and the taxpayer refuses to carry it, then business stagnates, with consequent unemployment, reduction of profits, and curtailment of government revenue. If a producer assumes the increased tax burden, marginal operations must be closed down, and, again the consequences are increased unemployment and diminished government revenue. Quite often an increase in a rate of tax results in a reduction of government revenue. Perhaps the worst detrimental feature of selfishness and greed on the part of any one of the three distributees of the fruits of industry is the retardation of expansion of the enterprise. Growth means new jobs, more government revenue, better trade, and better standards of living. Explorations and discoveries have resulted in tremendous contributions

Jan 1, 1964

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman, JOHN H. JANEWAY, Vice-Chairman. F. E. PIERCE, Secretary, 35 Nassau St., New York, N. Y. P. A, MOSMAN, Treasurer. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. HENRY A. WENTWORTH, Secretary-Treasurer, 60 India St., Boston, Mass. ROBERT H. RICHARDS,- ALBERT SAUVEUR. Columbia Holds four sessions during year. Annual meeting in September or October. FRANK A. ROSS, Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A. THOMSON.

Jan 7, 1915

By Gilbert E. Doan, William C. Schulte

An extensive program of investigation is being carried out at Lehigh University in the study of arcs and arc welds of high-purity iron1, sponsored by the Engineering Foundation. The part of that program reported in the present paper deals with welds made of high-purity iron in an argon atmosphere and for comparison with them welds made of the same iron in ordinary air. Welds of commercial steel also were made in argon and in air. The primary purpose of the study is to discover the basic physical constants of iron welds when not contaminated either by impurities in the iron or by the action of oxygen and nitrogen of the air during welding. Upon these constants can be founded such future studies as will determine what effects the various impurities and alloy elements present in steel have upon its welding characteristics, and what influence is exerted by the action of oxygen and nitrogen. The welding of steel involves such a multitude of variables, both of composition and of procedure, that development in the fabrication of this most important metal has necessarily been slow, wasteful, and in many instances discouraging. In the present investigation, the simplest possible condition has been selected; namely, iron practically free from contamination and a nonparticipating atmosphere, the inert gas argon. This simplification reduces the number of variables to a point where more rigid control of the system is possible. Although this study is significant for the contributions it makes to the science of steel fabrication, yet it is hoped that it will not be without value also in increasing knowledge of the. nature and behavior of iron and steel in general. From the standpoint of open-hearth practice, and to some extent from the standpoint of electric-furnace practice also, the conditions of melting and casting iron in this investigation are extraordinary. The casting temperature is high, the mean temperature of the metal probably reaching 2000' C. (3600' F.)? The rate of chilling of

Jan 1, 1936

By William C. Schulte, Gilbert E. Doan

An extensive program of investigation is being carried out at Lehigh University in the study of arcs and arc welds of high-purity iron1, sponsored by the Engineering Foundation. The part of that program reported in the present paper deals with welds made of high-purity iron in an argon atmosphere and for comparison with them welds made of the same iron in ordinary air. Welds of commercial steel also were made in argon and in air. The primary purpose of the study is to discover the basic physical constants of iron welds when not contaminated either by impurities in the iron or by the action of oxygen and nitrogen of the air during welding. Upon these constants can be founded such future studies as will determine what effects the various impurities and alloy elements present in steel have upon its welding characteristics, and what influence is exerted by the action of oxygen and nitrogen. The welding of steel involves such a multitude of variables, both of composition and of procedure, that development in the fabrication of this most important metal has necessarily been slow, wasteful, and in many instances discouraging. In the present investigation, the simplest possible condition has been selected; namely, iron practically free from contamination and a nonparticipating atmosphere, the inert gas argon. This simplification reduces the number of variables to a point where more rigid control of the system is possible. Although this study is significant for the contributions it makes to the science of steel fabrication, yet it is hoped that it will not be without value also in increasing knowledge of the. nature and behavior of iron and steel in general. From the standpoint of open-hearth practice, and to some extent from the standpoint of electric-furnace practice also, the conditions of melting and casting iron in this investigation are extraordinary. The casting temperature is high, the mean temperature of the metal probably reaching 2000' C. (3600' F.)? The rate of chilling of

Jan 1, 1936

By G. A. Mancini, V. Bharucha, J. W. Spretnak, G. W. Powell

The characteristics of the motion of the a interface during the "down" transformation was studied in zone-refined iron and dilute binary alloys containing nickel and molybdenum by means of the thermionic emission microscope and high speed photography. The frontal movements were found in all cases to be definitely discontinuous with time and an appreciable number of incremental jumps were found to proceed in the reverse direction (a to b). Molybdenum was found to be particularly effective in increasing the frequency of the increments of transformation from the stable to the metastable phase. A knowledge of the mechanism by which alloying elements affect the hardenability of a steel is desirable from both the practical and scientific viewpoints. It is well established that microstructures consisting of tempered martensite and lower bainite exhibit the best performance in terms of toughness and resistance to crack propagation. The presence of some upper transformation products, namely ferrite and pearlite, is in general undesirable. Various researches have indicated that the ferrite matrix grain structure is a very important difference between the upper and lower transformation products, namely equi-axed vs acicular. Any comprehensive theory of the decomposition of austenite should explain the dependency of the morphology of the matrix on undercooling. The contribution of various alloying elements to hardenability has been determined experimentally and catalogued in considerable detail. A rationalization of the basic mechanism or mechanisms by which individual elements affect the kinetics of the decomposition of austenite to products other than the phase "martensite" has not been evolved as yet. Interest in this problem was stimulated by the effects of minute quantities of boron in hardenable steels. This paper deals with one aspect of this problem, namely the characteristics of the ?-a transformation in high-purity iron and in two carbon-free iron binary alloys. A detailed historical account of the scientific developments in the study of the decomposition of austenite would be a prodigious undertaking and will not be attempted here. There are several excellent reviews in the literature on the formation of pearlite, martensitic reactions, and kinetics of solid-state reactions. The thinking on reaction mechanisms has been influenced to a large degree by the "classical" Tammann nucleation and growth model, in which an embryo springs into being by a fluctuation, and grows to a critical size through atom by atom deposition. Such a process is expected, accordingly, to be diffusion controlled. Considerable research attempting to relate the contribution of alloying elements to hardenability on the basis of their effect on the diffusivity of carbon in iron has not been productive from a mechanistic viewpoint. The formation of pearlite and ferrite has been treated in terms of nucleation and growth processes in which presumably the lattice transformation also occurs by a diffusion process. The other prominently considered mechanism is the "martensitic" or cooperative shearing mechanism. It seems generally, but not entirely, agreed that the phase "martensite" forms by this mechanism, and that it is involved to some extent in

Jan 1, 1962

By J. M. W. Mackenzie

The interactions between oil drops and mineral surfaces have been examined for the cetyltrimethylammonium bromide (CTAB)-quartz and sodium dodecyl sulfate (SDS)-hematite systems. The results have been interpreted using a electrical double layer interaction model, a "sweeping-penetration" model based on steric interactions and a free energy of adhesion model. The adsorption of long-chain ions at the mineral interface was also studied and found to follow a Fuerstenau-Modi model of combined Coulombic and chain-chain interaction forces. The basis of the emulsion flotation process and the feature which makes it differ from conventional flotation is: encounter, followed by adhesion, between oil drops and mineral particles which are suspended in an aqueous environment. The manner in which the adhesion between these two phases contributes to the flotation process may be through the formation of min-eral-oil drop-mineral linkages, mineral-oil drop-air bubble linkages, or a combination of both. Possible flotation mechanisms derived from these adhesion processes are shown schematically in Fig. 2 while Fig. 1 shows an example of the first mechanism for quartz particles which have been floated using a cetyltrimethyl-ammonium bromide (CTAB)-Nujol emulsion as collector. In Fig. 2 the three phases, mineral, oil, and air, for convenience have been shown as having approximately equal size. This would not always be the case in an actual emulsion flotation operation. For the flotation of sand-sized particles of approximately 0.5 mm diam, the mineral particles would be at least ten times the size of the largest emulsion drops present in the system, while in the flotation of —10u slime particles, the mineral phase may be of the same order of size as the oil phase. The air bubbles in a flotation cell are normally about 1 to 2 mm in diam and therefore, in general, would be larger than the oil drops. Although the relative size of the three phases does not alter the basic adhesion processes between oil drops, mineral particles, and air bubbles, which depend on the physical and chemical properties of the interfaces involved rather than on the extent of these interfaces, it does alter the degree of deformation of the oil drops and air bubbles which will occur on adhesion. For mechanisms 1 and 2 to take place, the oil-water and mineral-water interfaces must be partially replaced by a mineral-oil interface while in mechanism 2 there is the additional requirement that the oil-water and air-water interfaces must be replaced by an oil-air interface. In view of the importance of the oil drop-mineral particle encounter and subsequent adhesion stages to both of the emulsion flotation mechanisms discussed, a study has been made of some physicochemical factors which control these processes for Nujol-cetytri-methylammonium bromide (CTAB)-quartz and Nujol-sodium dodecyl sulfate (SDS) -hematite systems. Experimental Electrokinetic Measurements.—The zeta potential of mineral particles was measured using a streaming potential technique similar to that described by Fuerste-nau.1 The streaming potential was measured using a multirange electrometer while the plug conductivity was measured using a 50 cycle sec1 bridge. Measurements were made on 28 x 65 mesh particles. Contact Angle Measurements.—A captive bubble technique was used to measure the contact angles for air bubbles and oil drops. The angles were measured on fracture faces of unmounted minerals which proved easier to clean than polished mounted specimens and should more closely represent a flotation system. Reagents: These have been described in a previous publication.0 Minerals: Rock crystal quartz from the New England district, N.S.W., was used for contact angle and streaming potential measurements. The quartz was hand

Jan 1, 1971

By M. L. Millican

The objective of this study has been to develop a method of log interpretation in the Delaware sand whereby the effects of the shale contained within the sand can be recognized and accounted for in a quantitative solution for porosity and water saturation. Both theoretical and empirical considerations are discussed. A simplified interpretation chart is presented which provides a means of amending the conventional porosity resolution of the Sonic log to compensate for the presence of shale. The amount of shale within the sand and its degree of lamination may be inferred from a calibrated gamma ray log. The resulting porosity value may then be used in conjunction with a knowledge of the formation resistivity to determine water saturation. Of added interest, particularly in the Delaware sand, is an approximation of permeability which may be derived empirically from the simplified chart. The discussion is illustrated by field examples. INTRODUCTION The performance of the Sonic log in defining the porosity fraction in clean, consolidated formations is well known, particularly in sandstones that are well compacted and free of shale. An approach to Sonic log porosity determination in shaly sands has been recently developed.' This method involves correcting the Sonic log readings by means of an a factor, where a is the ratio of the pseudo-static SP to, the static SP, and is a function of the amount of shale present. This method is dependent upon a contrast between the salinities of the drilling fluid and the connate water in the formation, inasmuch as this contrast produces the SP effect. In wells drilled with salt mud, the contrast, and with it the means of obtaining the a correction, disappear. In the Delaware basin, the large majority of rotary wells drilled to the uppermost sands of the Bell Canyon group employ salt mud as the drilling fluid. These sands have been the objective of most of the drilling exploration in the basin to date. A comparison of porosity values in these sands, as determined by core analysis, to Sonic log readings has indicated that a correction for the shaliness of the sand is needed. In the absence of an SP curve to determine the correction factor, the porosity resolution of the Sonic log in these sands has been questionable.

By J. J. Kantner

CREEP investigators have made extensive studies to determine the interrelation of stress, temperature and the tensile creep rates of metals. It has been suggested that at small stresses the secondary or constant creep rates obey a simple viscous law. Building upon this suggestion, departure from pure viscosity as stress increases may be expressed mathematically as a consequence of reversibly altered viscosity or "flowability" in the same sense that temperature change reversibly alters viscosity. From the index to alteration of viscosity, a value for the energy of secondary creep may be derived having the magnitude of the free energy of vaporized metal. The suggestion is made that applica-tion of stress alters the energy of secondary creep. Strain energy is argued to be but a minor factor in the energetics of secondary creep. A deformation mechanism involving the large energy associated with secondary creep implies a sort of solid self-diffusion process. Evidence indicates that creep strain above the recrystallization temperature takes place by crystallographically directed self-diffusion at grain boundaries and points of crystal defects. A self-diffusion theory of secondary creep is proposed, embracing the principles of the Dushman-Langmuir theory of solid diffusion. An equation is suggested whereby the rate of tensile creep may be related directly to the physical and struc-tural character of the solid metal.

Jan 1, 1937

New York Meets first Wednesday after first Tuesday of each month: DAVID H. BROWNE, Chairman. JOHN H. JANEWAY, Vice-Chairman. F. E. PIERCE, Secretary, 35 Nassau St., New York, N. Y. P. A. MOSMAN, Treasurer. LEWIS W. FRANCIS. BENJAMIN B. LAWRENCE. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. HENRY A. WENTWORTH, Secretary-Treasurer, 60 India St., Boston. Mass. A. H. EUSTIS, F. G. STANTIAL. Columbia Holds four sessions during year. Annual meeting in September or October. FRANK A. ROSS, Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A. THOMSON.

Jan 1, 1916

By Harry L. Brown, James M. Dickinson, Philip E. Armstrong

The elastic stiffness coefficients of niobium have been rneaslrred from -150°C to over 650 C and ave in accord with the anomalous temperature dependence previously observed for Young's modulus. This unusual behavior has been shown to be the result of changes in the relative values of the shear elastic coefficients. The bulk modulus remained essentially constant over the temperature range studied, while changes in the shear coefficients produced a more nearly isotropic behavior as the temperature increased. A number of investigators have reported data on the temperature dependence of Young's modulus of polycrystalline niobium. The values cited for the room-temperature modulus ranged from 0.71 to 1.17 x 10" dynes-cm-' (10.3 to 17.0 x lo6 psi) and in each case the modulus was observed to decrease with increasing temperature. In our recent study,8 both polycrystalline and single-crystal samples of essentially strain-free high-purity niobium showed a Young's modulus whose temperature dependence as well as magnitude was strongly dependent on specimen orientation. This was shown to be the result of changes in the relative magnitude of the two shear moduli, C and C'. Young's modulus of polycrystalline samples with strong [110] textures and Young's modulus of single crystals whose orientations were away from the [loo] actually increased as much as 12 pct between room temperature and 1000°C. While studies on the residual effects of previous fabrication, thermal treatments, and impurity contents will probably resolve the problem of the widely differing Young's modulus values observed in polycrystalline niobium, a more complete description of the elastic properties requires an evaluation of the single-crystal elastic constants. A knowledge of these constants can provide a clearer picture of the nature of the temperature dependence, as well as establish a basis for predicting the modulus behavior of polycrystalline niobium, both in the randomly oriented condition and with various fabrication textures. The effects of residual strains on the elastic behavior then can be separated from orientation effects. EXPERIMENTAL METHOD Thin rod-resonance techniques were used to obtain both the Young's modulus and shear modulus of single-crystal specimens. The determination of these moduli as functions of the crystallographic orientation of the specimen axis provided sufficient information to permit calculation of the single-crystal elastic constants. The necessity for torsional as well as longitudinal measurements led to the design and assembly of a vertical-tube vacuum furnace incorporating probes for the simultaneous determination of both longitudinal

Jan 1, 1967

New York Meets first Wednesday after first Tuesday of each month. DAVID H. BROWNE, Chairman, JOHN H. JANEWAY, Vice-Chairman. F. E. PIERCE. Secretary, 35 Nassau St., New York, N. Y. P. A. MOSMAN, Treasurer. LEWIS W. FRANCIS. Boston Meets first Monday of each winter month. HENRY L. SMYTH, Chairman. ALFRED C. LANE, Vice-Chairman. HENRY A. WENTWORTH, Secretary-Treasurer, 60 India St., Boston, Mass. ROBERT H. RICHARDS, ALBERT SAUVEUR. Columbia Holds four sessions during year. Annual meeting in September or October. FRANK A. ROSS, Chairman. RUSH J. WHITE, Vice-Chairman. LYNDON K. ARMSTRONG, Secretary-Treasurer, P. O. Drawer 2154, Spokane, Wash. FREDERIC KEFFER, FRANCIS A. THOMSON.

Jan 8, 1915

By A. C. Watts

For several years, a mine in Colorado experienced considerable trouble from small fires caused by the blasting of coal. Although a well-known make of permissible powder was used, it was first thought that the powder ignited gas that might be present and that this, in turn, set fire to line brattices or to the coal. Experiments were, therefore, conducted with another make of powder, but the results convinced the superintendent of the mine, Robt. Williams, Jr., that the fires were not caused by the powder but by the high-voltage electric current used for detonating the shots. The mine "makes" gas very freely, giving off from three-fourths to one million cubic feet of methane every 24 hours. The coal is a good grade bituminous of a very free burning quality. Electric shot-firing from the outside, after all men and animals were outside, had been practiced for a number of years. The shooting circuit was connected with the main power circuit at the mouth of each entry. Shooting circuit switches were mounted in boxes, which were kept locked with the handle of the switch, in open position, showing through the bottom of the box. The door of the box could not be shut and locked when the shooting switch was closed. At the entrance to each room, or working place, a small switch, called the miner's switch, was placed on the shooting line. It was the duty of the miner, when entering his place at the beginning of the shift, to see that this switch was open and that it was kept open until he left the placc at the end of the shift to go out of the mine. Grounded return was used for main power lines. The current was 500 volts, direct current, with 100 to 300 amp. The nearest working face was 9600 ft, from the shot-firers' switch outside the mine and the most remote working face was 2½ miles. The various working faces were scattered over a wide area between these two points. A description of the main power line would be valueless; the conductors were of sufficient size, the drop in voltage being not more than

Jan 1, 1927

By B. Fazan, O. D. Sherby, J. E. Dorn

McLean's technique was employed to determine the effect of temperature on the contribution of grain boundary shearing to the total creep strain in pure aluminum over the range of 610° to 747°K. The contribution of grain boundary shearing at the same stress was found to depend upon a temperature-compensated time, where the activation energy AH was practically identical with that for total high temperature creep. SEVERAL outstanding investigations by McLeanl-' have demonstrated that the total creep strain in polycrystalline aluminum at 473°K arises from microscopically detectable slip, subgrain tilting, and grain boundary shearing. Whereas microscopically detectable slip arises from dislocations that move out of the grains, subgrain tilting is due to entrapment of dislocations of like sign in subgrain bound-arles. Consequently, creep in polycrystalline aggregates appears to be the resultant of two mechanisms, namely, migration of dislocations and grain boundary shearing. This suggests that an appropriate law for creep should contain two additive terms ?1 = ?d + ?yb where the total creep strain, ?1, depends on the sums of the creep strains arising from motion of dislocations, ?d, and from grain boundary shearing, ?yb. But extensive investigations5 over wide ranges of alloys, grain sizes, temperatures, and stresses have shown that the total creep strain is quite accurately dependent on the single term functional relationship ?1 = f (?), s = constant where s is the stress (constant),* ? = te-?H/RT, t is the time under stress, AH is the activation energy, R is gas constant, and T is absolute temperature. Since Eq. 2 was found to be valid over those ranges where appreciable grain boundary shearing is observed, it appears probable that the activation energy for grain boundary shearing might be identical with the activation energy for migration of dislocations. Thus, under a given stress, it could be thought that where fd and fgb represent the appropriate functions for each mechanism of creep. The primary objective of this investigation was to obtain a direct check on the accuracy of this hypothesis. Experimental Procedure and Results Rolled aluminum sheet (99.987 pct Al), 0.100 in. thick, was used in this investigation. Creep specimens having a 0.25 in. wide, 3 in. long gage section were so machined that their axes were in the rolling direction. All specimens were annealed for 9 hr at 894°K before testing to produce a mean grain diameter of about 0.1 in. One face of each specimen was polished electrolytically in 10 pct HBF4. In order to permit accurate measurements of grain boundary shearing, the polished surface was lightly scribed with a ruling machine accurate to ±0.0001 in. to give a uniform grid of lines which were 0.01 in. apart. Although it was thought that surface working might modify the creep behavior in the vicinity of the scribed grid lines, this technique nonetheless was employed because such local differences in creep properties should not modify seriously the fractions of the total creep strain due to grain boundary shearing or to migration of dislocations. All creep tests were conducted under constant load with an initial stress of 250 psi. The specimen tem-

Jan 1, 1955

By N. Plint, E. T. Pinkney

Copper segregation developments within the Anglo American Group are described with particular reference to the work of the TORCO Project Team. Some radical differences have been adopted in the mechan-ical approach as compared with methods used by previous workers. Most important among these are the following: (1) The heating unit is a fluidized-bed roaster. (2) A moving bed segregation chamber is used in which a packed bed of heated ore, to which reagents have been added, moves slowly downwards under gravity and is discharged at a controlled rate by means of a suitable valve mechanism. (3) The quantities of reagents used (sodium chloride and some form of carbon) are only a small fraction of those recommended by other investigators. (4) Retention times of only 2 min have been satisfactory for the complete segregation of many types of ore. Project TORCO is the code name given by Anglo American Corp. of South Africa, Ltd., to the investigation undertaken in Zambia to develop a plant capable of treating large tonnages of refractory copper-bearing ores by the segregation process. The process has now been under investigation for six years (1960-66) and during that period work has progressed from bench-scale laboratory tests through small-scale pilot-plant work to a 500-tpd commercial pilot unit. Test work has been carried out mainly on the ores of the Zambian Copperbelt and results have been encouraging. Recoveries on the order of 90% have been obtained on all Copperbelt ores tested with high concentrate grades. PRELIMINARY INVESTIGATION Laboratory scale segregation test work on Nchanga banded sandstone ore and oxidized ore from Kansan-shi was originally conducted by Professor Maurice Rey. SociCtC Miniere et Mktallurgique de Pefiarroya, in 1957. Both ores responded favorably to the process. In November, 1960, the consulting engineers of Anglo American Corp. of South Africa, Ltd., initiated preliminary investigations on the application of the segregation process to Copperbelt ores. In early laboratory work, samples were heated in a closed, externally heated tube furnace for one hour at temperatures ranging from 800 to 830°C. The free moisture content of the ore feed was 4% and reagent additions were 0.5% salt and 1.0% coal. Both salt and coal were pre-crushed to -48 mesh Tyler.* All samples except an ore from the Bancroft mine responded well to the process and recoveries of over 90% were obtained. The presence of dolomite was responsible for the relatively poor recoveries from the Bancroft ore, as tests on one of the other ores with additions of calcite or dolomite confirmed. Recoveries dropped from 94 to 45% Grades of all the rougher flotation concentrates produced were low at 10-15% copper. The laboratory investigation was then followed up on a pilot-plant scale. An attempt was made to carry out the segregation process in a coal-fired 5-ft-diam fluidized-bed roaster. The feed consisted of a banded sandstone from Nchanga to which 0.5% sodium chloride had been added. Reducing conditions were maintained in the roaster by the addition of coal in excess of that required for heating the feed. The excess coal and added salt constituted the segregation reagents and the temperature of the bed was held at approximately 750°C. Recoveries of copper and grades of concentrates were low. The reasons for lack of success were: (1) The reaction is a gaseous one and a fluidized-bed roaster is therefore unsuitable as a segregation unit. (2) Coal in excess of that required for heating was introduced into the fluidized bed and under these conditions some of the copper would be reduced in situ. The term "reduced in situ" is used here to describe any copper mineral reduced to the metallic state in its original site within the ore particles. If this copper is to be recovered by subsequent froth flotation it must first be liberated from the gangue by grinding or some other method which, in practice, is usually not feasible on ores of this type.

Jan 1, 1969

By A. Hultgren, B. Herrlander

The original aim of the present investigation was to study the mechanism of cracking on hot-deforming red-short steels. During the microscopical examination of hot-deformed soft steels attention was directed to various patterns of so-called veining in the ferrite, as related to variations in the deformation procedure and the heat-treatment of the steels. Later, a hot-short steel of higher carbon content was also studied. Historical Storey1 suggested in 1914 that veining developed during the gamma-alpha transformation from the growing together of several alpha nuclei within the same gamma grain. Rawdon and Berglund2 found that in soft steel, forged somewhat below A3, the ferrite showed profuse veining, while usually there was very little veining after forging at very high temperatures. They emphasized the similarity between the pattern of veining formed by deformation about 600°C and that of slip lines formed by deformation at room temperature. They also suggested a relation between the gamma-alpha transformation and veining. They became convinced from etching and from the slip-line pattern in cold-deformed material, that the orientation within any ferrite grain showing veining was uniform. In recrystallized alpha grains veining was absent. Veining did not appear materially to affect the properties of ferrite. Independent of veining, continuous networks, attributed to preexisting delta and gamma grain boundaries were sometimes found, the former only in cast steel. Those networks were usually connected with small inclusions. Ammermann and Kornfeld3 confirmed that recrystallized ferrite grains showed no veining. In soft steel annealed between A1 and A3 there was veining only in the ferrite grains formed during cooling. Electrolytic iron deformed at 880' was free from veining. Bannister and Jones' considered veining in ferrite to be a manifestation of microscopical and sub-microscopica~ inclusions. NorthCOtt,5,6 in studies on veining in steel and other metals and alloys, attributed veining to oxide inclusions. It could generally be removed by annealing in hydrogen, a suggestion earlier made by Rawdon and Berg1und. TrittOn (discussion in ref. 5) emphasized the importance of perfect polishing for bringing out veining by etching, and thought the veins or subboundaries were produced during the gamma-alpha transformation, when it was rapid, as a result of the volume change and contraction during cooling. Slight distortion would not allow projecting parts of a growing crystal to join up with atomic symmetry. Hanemann and co-workers showed that veining in ferrite consisted of ridges

Jan 1, 1948

By B. Herrlander, A. Hultgren

The original aim of the present investigation was to study the mechanism of cracking on hot-deforming red-short steels. During the microscopical examination of hot-deformed soft steels attention was directed to various patterns of so-called veining in the ferrite, as related to variations in the deformation procedure and the heat-treatment of the steels. Later, a hot-short steel of higher carbon content was also studied. Historical Storey1 suggested in 1914 that veining developed during the gamma-alpha transformation from the growing together of several alpha nuclei within the same gamma grain. Rawdon and Berglund2 found that in soft steel, forged somewhat below A3, the ferrite showed profuse veining, while usually there was very little veining after forging at very high temperatures. They emphasized the similarity between the pattern of veining formed by deformation about 600°C and that of slip lines formed by deformation at room temperature. They also suggested a relation between the gamma-alpha transformation and veining. They became convinced from etching and from the slip-line pattern in cold-deformed material, that the orientation within any ferrite grain showing veining was uniform. In recrystallized alpha grains veining was absent. Veining did not appear materially to affect the properties of ferrite. Independent of veining, continuous networks, attributed to preexisting delta and gamma grain boundaries were sometimes found, the former only in cast steel. Those networks were usually connected with small inclusions. Ammermann and Kornfeld3 confirmed that recrystallized ferrite grains showed no veining. In soft steel annealed between A1 and A3 there was veining only in the ferrite grains formed during cooling. Electrolytic iron deformed at 880' was free from veining. Bannister and Jones' considered veining in ferrite to be a manifestation of microscopical and sub-microscopica~ inclusions. NorthCOtt,5,6 in studies on veining in steel and other metals and alloys, attributed veining to oxide inclusions. It could generally be removed by annealing in hydrogen, a suggestion earlier made by Rawdon and Berg1und. TrittOn (discussion in ref. 5) emphasized the importance of perfect polishing for bringing out veining by etching, and thought the veins or subboundaries were produced during the gamma-alpha transformation, when it was rapid, as a result of the volume change and contraction during cooling. Slight distortion would not allow projecting parts of a growing crystal to join up with atomic symmetry. Hanemann and co-workers showed that veining in ferrite consisted of ridges

Jan 1, 1948

By T. V. Philip, R. E. Lenhart

When commercial silicon iron sheets of varying magnetic quality are isothermally annealed at high temperatures, extremely large grains develop in the material having good magnetic properties. These grains are of the (110) [001] orientation and are formed by secondary recrystallization. The primary driving force for this secondary recrystallization is grain boundary free energy. For the secondary grains, activation energies of 103 kcal per mole for nucleation, and of 75.5 kcal per mole for growth, were obtained. The activation energy for nucleation of the secondary grains is consistent with a model involving redistribution of a precipitate acting as the primary grain growth inhibitor. SINGLY oriented silicon iron sheet was first produced in 1935.1 The material as commercially produced today has a very highly developed preferred orientation or texture; up to 95 pct of the grains are crystallographically oriented with their (110) planes in the plane of the sheet and their [loo] directions parallel to the rolling direction. This texture, usually written as (110) [00l], is referred to as the "GOSS" or the "cube-on-edge" texture. Because the magnetic properties of this material are superior to those of the nonoriented sheets in the direction of rolling, the oriented silicon iron has acquired tremendous industrial importance especially in the manufacture of transformer cores and other electrical equipment. The commercially produced material is essentially an iron-silicon alloy containing about 3 1/4 pct Si with minor impurities totaling less than 0.15 pct. The silicon steel heat is melted in the open hearth or electric furnace. The ingots are hot rolled, with or without being slabbed, to strips of 0.100 to 0.080 in. thickness. They are then cold reduced to an intermediate thickness, recrystallized, cold reduced to final thickness, decarburized, and finally annealed at a high temperature. During this high-temperature anneal, extremely large grains with the cube-on-edge texture are produced in the sheet. Several papers have appeared in the literature2-10 relating to the production of the Goss-textured material. Most of these describe the textures produced on cold rolling and on subsequent annealing of single crystal or polycrystalline silicon iron. May and Turnbull11,12 have recently shown the necessity of a second-phase dispersed impurity in the material for the production of the Goss texture. However, none of these papers describes in detail the nucleation and growth kinetics of the (110) [001] grains during the final high-temperature anneal.* The present work, therefore, is an attempt to understand the nucleation and growth kinetics of the cube-on-edge grains in the silicon iron sheet during the final high-temperature anneal.

Jan 1, 1962

By Earl Hanson

FIRES in heavily timbered mines are disastrous, involving danger to both life and property. Some mines have been completely ruined or so heavily damaged that reopening them would not pay. Though few mines are entirely free from danger of fire, the risk is minimized by proper care and good design of plant. The Tintic Standard mine is at Dividend, Utah, in the famous Tintic mining district, about 60 miles south of Salt Lake City. The development of the mine was begun in 1907 by the late Mr. E. J. Raddatz and his associates. From the beginning, the work was hampered by high rock temperatures and the presence of high concentrations of rock gases such as carbon dioxide and nitrogen. Development work was carried on with great perseverance for nine years, and resulted in the discovery of ore in 1916. The total production of the Tintic Standard mine to Jan. 1, 1936, amounted to 1,664,388 tons of ore, having a gross value of .$61,996,719.

Jan 1, 1936

By W. M. Robertson

The kinetics of grain boundary groove formation on copper surfaces immersed in liquid lead have been studied over the temperature range of 400° to 900°C. The groove widths were Proportional to the cube root of the annealing time, indicating that the diffusion of copper through the saturated liquid-lead solution is the mechanism by which grooves form. The rate constant for the process can be calculated by a theory due to Mullins. Using published data for the solubility of copper in liquid lead, for the interfacial energy of the solid copper-liquid lead interface, and for the diffusion coefficient of copper in liquid lead, the calculated rate constants almost exactly reproduce the measured values over the entire temperature range. The decay of scratches placed on copper surfaces has also been studied. The rate constant for scratch decay agrees with that for grain boundary groove growth, though scratch decay is sensitive to convection currents in the liquid. The interaction of solid and liquid metals has been studied extensively and has been found to be rather complex. Many of the studies have been complicated by a host of competing effects, including temperature gradients, concentration gradients, the formation of one or more intermetallic phases, natural or forced convection, and the presence in both the solid and liquid of considerable amounts of impurities and alloying elements. Recently theories have been developed of changes in surface profiles driven by capillary forces,' which allow the interaction of the solid and liquid to be analyzed quite directly. The present paper reports a study of the formation of grain boundary grooves on pure copper immersed in liquid lead, which allows the theory to be checked quantitatively. The Cu-Pb equilibrium diagram is quite simple: there are no intermetallic compounds, copper is just slightly soluble in liquid lead, and lead is almost completely insoluble in solid copper.2 The Cu-Pb system has been studied extensively,3-9 and all of the quantities—interfacial energy, diffusion coefficients, and equilibrium solubilities-necessary to calculate the rate of groove growth by a volume-diffusion mechanism are known. The kinetics of grain boundary grooving and scratch smoothing have been studied on the noble metals and the iron group metals in a reducing atmosphere or in vacuum.10 The main interest of these studies has been the determination of surface-diffusion coefficients at metal-gas interfaces using the theories developed by Mullins.1 The present paper uses similar methods for the study of diffusion processes at the interface between two condensed phases. There has been one previous study" of the kinetics of groove growth in a solid-liquid system, which, however, was troubled by the fact that neither interface energies nor diffusion coefficients were known in the Ni-S system studied. THEORY The theory of grain boundary groove growth has been developed by Mullins for the cases of volume diffusion," surface diffusion," and a combination of the two processes.14 He has also analyzed the kinetics of the flattening of a scratched surface by these processes.l5,l6 Several assumptions and approximations were used in the derivations of the surface profile shapes. The applicability of these assumptions and approximations to the present system will be considered in the discussion. At the intersection of a grain boundary with an initially flat interface the equilibrium between the interfacial energy and the grain boundary energy establishes an equilibrium groove angle. This induces curvatures in the interface. The chemical potential of material at a curved interface is higher than at a flat interface, so that material moves away from the region of the grain boundary. Mullins' calculations indicated that the groove profile would be similar to that shown schematically in Fig. 1. Small humps form above the level of the original flat surface. For a volume-diffusion mechanism the separation, w, of these humps at a time, t, is given by and where co is the equilibrium concentration of the solid in the liquid, y, the solid-liquid interfacial free energy, O the volume occupied by a solute atom in the liquid, D the diffusion coefficient of the solid in the liquid, and kT has its usual meaning. For a surface-diffusion mechanism the groove width is proportional to the fourth root of the time. For grooves forming by a combined surface and volume-diffusion mechanism the exponent of the

Jan 1, 1965