Search Documents

By J. L. Carne

ORE control is a matter of planning and supervision based on a foreknowledge of the content and distribution of ore. The Inspiration orebody is predominately a copper-sulphide blanket, overlain by an oxidized zone of copper silicates, copper carbonates, and barren capping. Most of the ore is treated by leaching, and the optimum requirement of this method is the goal toward which the mining schedule is aimed. Both open-pit operations and underground mining are used. The problems of ore control at Inspiration are: I—maintenance of metallurgical balance, 2—conservation of oxide ore, and 3—mining out of the orebody at an average grade which parallels that of the reserve figure. Prior to the fall of 1926 all of the Inspiration division ores were treated by flotation, but the mixed ores of the Live Oak—Keystone section carried too large a proportion of copper in the form of chrysocolla for satisfactory flotation. For this type of mixed ore the leaching process now in use had been worked out, and the plant was put into operation in the fall of 1926. The process is known as the ferric sulphate leach, and the leaching solvents contain both ferric sulphate and free sulphuric acid. Sulphide copper in the form of chalcocite is leached by the ferric sulphate, and the oxidized copper minerals are dissolved by the sulphuric acid. From the beginning of operations to the present time the plant has treated some 67 thousand tons of ore having an average copper content of 1.142 pct, of which 0.605 pct has been in the form of oxidized copper minerals. The plant is currently being operated at the rate of 11,500 tons per day, 7 days per week. However, this tonnage is produced in 6 days of mine operation. The average current grade is approximately 1 pct copper, of which about 50 pct is present as oxidized or acid-soluble copper. Close control of metallurgical procedures is a vital factor in operation of the plant and is in turn dependent upon careful regulation of feed. An excess of sulphide copper requires the presence of more ferric sulphate in the leaching solvents. On the other hand, an excess of ferric sulphate in the presence of a low sulphide feed seriously reduces the efficiency of electrolytic precipitation in tank house operations. This condition must be avoided at all costs. An additional factor must be considered. It is known that the sulphide content is predominant in the ore which remains in the reserve. To maintain the necessary sulphide-oxide proportion, so that the entire reserve will mine out at both a grade and a sulphide-oxide ratio that will be permissible throughout the remaining life of the property, it is obvious that the oxide reserve must be currently preserved to as great an extent as possible. Fortunately much of the oxide reserve is found in the open-pit operation. This happy circumstance adds flexibility to the procedure and makes it possible to maintain the close regulation necessary to insure best overall results, both mining and metallurgical. The two ore streams from the pit and underground operations join at the coarse-crushing plant, and proper control must be exercised before the ore reaches this point. The open pit is currently providing about 55 pct of the ore and underground operations the balance of production. Both operations are under a single superintendent so that the closely interrelated problems may be more readily controlled. The least flexible of the two producing units is the underground mine, where the mining method is block caving. Although a block of ground may be undercut and developed, characteristics of the material determine its caving action. The ore in the chutes must be drawn. The area currently mined from underground is in a zone predominately sulphide and is generally

Jan 1, 1953

By J. L. Carne

ORE control is a matter of planning and supervision based on a foreknowledge of the content and distribution of ore. The Inspiration orebody is predominately a copper-sulphide blanket, overlain by an oxidized zone of copper silicates, copper carbonates, and barren capping. Most of the ore is treated by leaching, and the optimum requirement of this method is the goal toward which the mining schedule is aimed. Both open-pit operations and underground mining are used. The problems of ore control at Inspiration are: I—maintenance of metallurgical balance, 2—conservation of oxide ore, and 3—mining out of the orebody at an average grade which parallels that of the reserve figure. Prior to the fall of 1926 all of the Inspiration division ores were treated by flotation, but the mixed ores of the Live Oak—Keystone section carried too large a proportion of copper in the form of chrysocolla for satisfactory flotation. For this type of mixed ore the leaching process now in use had been worked out, and the plant was put into operation in the fall of 1926. The process is known as the ferric sulphate leach, and the leaching solvents contain both ferric sulphate and free sulphuric acid. Sulphide copper in the form of chalcocite is leached by the ferric sulphate, and the oxidized copper minerals are dissolved by the sulphuric acid. From the beginning of operations to the present time the plant has treated some 67 thousand tons of ore having an average copper content of 1.142 pct, of which 0.605 pct has been in the form of oxidized copper minerals. The plant is currently being operated at the rate of 11,500 tons per day, 7 days per week. However, this tonnage is produced in 6 days of mine operation. The average current grade is approximately 1 pct copper, of which about 50 pct is present as oxidized or acid-soluble copper. Close control of metallurgical procedures is a vital factor in operation of the plant and is in turn dependent upon careful regulation of feed. An excess of sulphide copper requires the presence of more ferric sulphate in the leaching solvents. On the other hand, an excess of ferric sulphate in the presence of a low sulphide feed seriously reduces the efficiency of electrolytic precipitation in tank house operations. This condition must be avoided at all costs. An additional factor must be considered. It is known that the sulphide content is predominant in the ore which remains in the reserve. To maintain the necessary sulphide-oxide proportion, so that the entire reserve will mine out at both a grade and a sulphide-oxide ratio that will be permissible throughout the remaining life of the property, it is obvious that the oxide reserve must be currently preserved to as great an extent as possible. Fortunately much of the oxide reserve is found in the open-pit operation. This happy circumstance adds flexibility to the procedure and makes it possible to maintain the close regulation necessary to insure best overall results, both mining and metallurgical. The two ore streams from the pit and underground operations join at the coarse-crushing plant, and proper control must be exercised before the ore reaches this point. The open pit is currently providing about 55 pct of the ore and underground operations the balance of production. Both operations are under a single superintendent so that the closely interrelated problems may be more readily controlled. The least flexible of the two producing units is the underground mine, where the mining method is block caving. Although a block of ground may be undercut and developed, characteristics of the material determine its caving action. The ore in the chutes must be drawn. The area currently mined from underground is in a zone predominately sulphide and is generally

Jan 1, 1953

By D. W. Fuerstenau

THE object of this article is to point out the experimental relationship which exists among contact angle, adsorption density, zeta potential, and flotation rate data. In each of the experiments discussed in this article, the surface properties of quartz, as a function of pH, were measured in solutions to which constant quantities of dodecylam-monium acetate were added. Morrow1 and deBruyn2 worked with solutions containing 4.08x10-5 moles per liter, whereas Fuerstenau3 and Seele worked with solutions containing exactly 4x105 moles per liter, but this difference is not significant. The pH of the solutions was regulated with HCI or NaOH in all cases. In each case, the addition of collector was constant, but the concentration of dodecylammonium ions decreased because of the formation of dodecylamine at higher pH values.2 Contact Angles: Gaudin and Morrow1 presented data for the contact angle of quartz in solutions containing 4.08x10-5 moles of dodecylammonium acetate per liter between pH 2 and pH 10.15. Using the same captive bubble techniques, the writer measured contact angles on quartz in solutions containing 4x105 moles of dodecylammonium acetate per liter at pH values ranging from 9.9 to 13.2. Both sets of data are presented in Fig. 1, in which the contact angle in degrees is plotted as a function of the pH of the solution. From pH 2 to about 8, the contact angle

Jan 1, 1958

By J. W. Rutter, K. T. Aust

Observations are presented of the formation of annealing twins during the growth of a recrystallized grain into a striated, melt-grown crystal of high-purity lead. The formation of an annealing twin resulted in replacement of the original migrating boundary by a large-angle grain boundary of the caincidence-site type or by a near-twin boundary. The results support the Fullman-Fisher theory of annealing twins and demonstrate the usefulness of the coincidence-site model. FULLMAN and Fisher1 have advanced the following theory to account for the formation of annealing twins during grain growth. Whenever a grain A grows into a matrix of grains S1 and S2, a twin A' of grain A may form, as shown in Fig. 1, if the following energetic condition is satisfied: where "E" and "a" refer to the specific interfacial free energy and the area, respectively, of the boundaries indicated by the subscripts. In effect, the twinned grain will persist when the energy of the boundary between the twin(A') and the matrix grain (S, or S,) is less than that of the boundary between the original growing grain (A) and the matrix grain by an amount which exceeds the energy of the coherent twin boundary between A and A'. Experimental observations on the changes in grain boundary free energy accompanying the formation of twins1 are in agreement with the theory outlined in Eq.[l]. Direct observations of the formation of annealing twins at moving grain corners1"3 and the depend-

Jan 1, 1961

By G. Gutzeit

An inner complex is a cyclic chemical structure containing an inorganic cation that is bound simultaneously to several atoms in a single organic molecule; on the one hand by means of ordinary valence bonds (electron exchange), on the other hand through the action of the electric field thus created, which satisfies the so-called secondary valences. The relative positions of the salt-forming and complex-forming groups are such that most frequently a four, five, or six-membered ring results through this double attachment of the cation.1-6 The formation of inner-complex ring systems depends not only upon the nature and suitable position of the salt-forming and complex-forming groups for ring closure, but, to a great extent, also on the nature of the metallic cation entering the reaction. This selective character of chelate-forming organic compounds is one of their most interesting and most valuable properties. As a matter of fact, the largest number of their practical applications is based upon their specificity.4,7-l3 Once a chelate compound is formed, its character is definitely "organic" in nature. In other words, its properties are conditioned to a much larger degree by the carbon chains or rings than by the metallic atom. Many inner complexes are soluble in nonpolar solvents such as benzene, paraffin oil or carbon tetrachloride, while the chelate-forming reagent before closure of the metal-organic ring is water soluble. (Example: copper complex of salicyl-aldoxime') It is obvious that such particular properties as those indicated above can be utilized whenever specificity and practically complete binding of inorganic ions into an undissociable complex are required. One of the well-known applications of chelate-forming compounds has been the development of specific reagents in analytical chemistry, creation of the spot-test method,4,14-16 and the application of the same principles to the contact print method for determining minerals." Chelate-forming Compounds as Collectors In the field of flotation, where selectivity is often a quality of paramount importance for the collector, various workers have lately attempted to apply their knowledge of specific organic analytical reagents to this purpose. A. C. Vivian18 has concentrated cassiterite by using ammonium nitrosophenylhydroxyl-amine (Cupferron) C6H5NO(=NONH4). Holmanl9 has tested dimethylglyoxime for the flotation of nickel oxide minerals, while deWitt has shown in a series of systematic experiments that alpha-diox-imes were generally selective collectors for nickel ores. Taurin NH2(CH2)2S03H has been proposed for the concentration Of Oxidized lead ores.19 Diphenylthio-carbazone

Jan 1, 1947

By G. Gutzeit

An inner complex is a cyclic chemical structure containing an inorganic cation that is bound simultaneously to several atoms in a single organic molecule; on the one hand by means of ordinary valence bonds (electron exchange), on the other hand through the action of the electric field thus created, which satisfies the so-called secondary valences. The relative positions of the salt-forming and complex-forming groups are such that most frequently a four, five, or six-membered ring results through this double attachment of the cation.1-6 The formation of inner-complex ring systems depends not only upon the nature and suitable position of the salt-forming and complex-forming groups for ring closure, but, to a great extent, also on the nature of the metallic cation entering the reaction. This selective character of chelate-forming organic compounds is one of their most interesting and most valuable properties. As a matter of fact, the largest number of their practical applications is based upon their specificity.4,7-l3 Once a chelate compound is formed, its character is definitely "organic" in nature. In other words, its properties are conditioned to a much larger degree by the carbon chains or rings than by the metallic atom. Many inner complexes are soluble in nonpolar solvents such as benzene, paraffin oil or carbon tetrachloride, while the chelate-forming reagent before closure of the metal-organic ring is water soluble. (Example: copper complex of salicyl-aldoxime') It is obvious that such particular properties as those indicated above can be utilized whenever specificity and practically complete binding of inorganic ions into an undissociable complex are required. One of the well-known applications of chelate-forming compounds has been the development of specific reagents in analytical chemistry, creation of the spot-test method,4,14-16 and the application of the same principles to the contact print method for determining minerals." Chelate-forming Compounds as Collectors In the field of flotation, where selectivity is often a quality of paramount importance for the collector, various workers have lately attempted to apply their knowledge of specific organic analytical reagents to this purpose. A. C. Vivian18 has concentrated cassiterite by using ammonium nitrosophenylhydroxyl-amine (Cupferron) C6H5NO(=NONH4). Holmanl9 has tested dimethylglyoxime for the flotation of nickel oxide minerals, while deWitt has shown in a series of systematic experiments that alpha-diox-imes were generally selective collectors for nickel ores. Taurin NH2(CH2)2S03H has been proposed for the concentration Of Oxidized lead ores.19 Diphenylthio-carbazone

Jan 1, 1947

By Joseph J. Yancik, Leonard L. Felts, George B. Clark

LITTLE information has been published concerning the actual or useful amount of energy obtained from explosives when they are used for blasting. To provide more data on this subject, 8-in. neet cement cubes were blasted in a steel plate box and the breakage energy evaluated by comparison with drop crusher results using Rittinger's,1,2 Kick's: and Bond's' theories. Theories by Bond and Wang," Lineau," Hatch,' Roller,' and others0-11 were not considered applicable. Those used in this investigation may be expressed mathematically as follows: Rittinger Theory E = KrS2, pet,—--------------- [1] 40 d1 d0 Kick Theory TV 1 1 E = =K, [S pct. log1/d+ 100 log d0] [2] 40 d1 L. L. FELTS, Junior Member AIME, was formerly a Graduate Assistant, University of Illinois. G. B. CLARK, Member AIME, was formerly Professor of Mining Engineering, University of Illinois, and is now Chairman, Dept. of Mining Engineering, Missouri School of Mines and Metallurgy. J. YANCIK, Junior Member AIME, is a Graduate Assistant, Missouri School of Mines and Metallurgy. This paper, TP 4213A. is revised from a thesis submitted by L. L. Felts in partial fulfillment of the M.S. degree in Mining Engineering, University of Illinois, 1954. Discussion may be sent (2 copies) to AIME before May 31, 1956. Manuscript, Dec. 27, 1954. Bond's Third Theory E = Kb [S pct. log1/d1+ 100 log d0] where E — energy used in breakage, d, = average diameters of screen fractions of broken cement particles, pct, = percent weight of diameter d;, and 2 pct, = 100 pct. The above equations were employed to determine values of Kr, Kk, Kb for particle size distributions similar to those obtained from the blasting curves. These values were in turn used as a means of approximating the specific energy of the blasted material. The efficiency of crushing by blasting was then determined by dividing this specific energy by the maximum available work of the explosive per gram of cement. Knowledge of the failure of solids under static loads is developing very rapidly. Their failure under impact loads has been investigated and reported in the literature only to a limited extent. Theories of failure' hnder static loading include 1) the maximum stress theory, 2) the maximum strain theory, 3) the theory of constant elastic strain, 4) theory of maximum shearing stress, and 5) Mohr's theory of strength. All of these have elements of usefulness in establishing an applicable theory for blasting. For highly strained and compressed material such as that surrounding a detonating charge of high explosive, the Mohr theory and its implications appear to be the

Jan 1, 1957

By J. B. Austin

IN developing a consistent picture of the thermal expansion of the commercial chromium steels, which cover a range of carbon contents, it is desirable to know the expansion in the limiting case of the binary, carbon-free, iron-chromium alloys. We have, therefore, determined the thermal expansion of a series of five special alloys, ranging in chromium content from 3 to 10.5 per cent, with not more than 0.03 per cent carbon, over a temperature range extending beyond the transformation region; this low carbon content enables us to draw reasonably reliable conclusions as to the behavior of the carbon-free system. Moreover, the measure-ments serve to determine the beginning and the end of the alpha-gamma transformation; and they emphasize once more the fact that a transforma-tion temperature determined by any method in which the specimen is cooled at an appreciable rate is apt to be seriously in error, particularly if the metal contains a transformation-retarding element such as chro-mium or managanese. The lag, or undercooling, observed at the ? - a transformation is explained in terms of the influence of temperature on transformation velocity; the rather unusual shape of the ? loop is attributed to a change with temperature and with composition of the distribution of chromium between the alpha-iron and gamma-iron solid solutions. The exact composition of the alloys which were obtained through the courtesy of Dr. W. Rohn, of the Heraeus Vakuumschmelze A-G., is given in Table 1. Determinations of the linear thermal expansion and of transformation temperature were carried out in the vacuum dila-tometer previously described,1 using a rate of heating and of cooling of 3.0° to 3.5° per minute unless otherwise stated. Magnetic susceptibility, which was measured in studying the rate of transformation, was determined with a magnetic balance, which also has been described.2

Jan 1, 1935

Truman H. Aldrich '78 W. S. Ayres '73 Andrew A. Blair '75 Walter M. Brodie '72 H. M. Chance '74 Fred'k G. Corning '77 Ralph Crooker '81 A. W. Crookston '80 George M. Davidson '81 W. B. Devereaux '80 H. S. Drinker Founder

Jan 1, 1929

By Lawrence K. Jetter, Robert F. Mehl

Some advances have been made recently in the theory of the kinetics of precipitation from metallic solid solution despite the complexities of the problem, but there is surprisingly little quantitative information available on rates of precipitation with which to test present theory or upon which to build new theory. Attempts to measure rates of precipitation have been beset with difficulties which originate both in the anomalies that attend the changes in the properties selectcd for measurement, as, for example, in electrical conductivity or mechanical properties, and also in the complexities in the structural changes in some systems, as in the aluminum-copper system. If the functional relationship between the quantity of precipitate and the value of the selected property is uncertain, measurements of that property are obviously of uncertain utility in determining absolute rates of precipitation. If the precipitating system passes through one or more transition stages, the interpretation of measured rates lacks definiteness; in such cases, it is necessary to measure the rate of reaction in each separate stage, if the rate measurements are to have any significance from the kinetic point of view.* These difficulties cannot be wholly avoided, for at least in some measure they are characteristic of the process of precipitation from solid solution, but they can be minimized both by the selection of a simple system and by the use of a method of measurement relatively free from anomalous behavior. The present paper reports dilatome tric measurements on the rate of precipitation of silicon from the aluminum-rich solid solution in the aluminum-silicon system—a study that approaches the desiderata of simplicity. The aluminum-silicon system offers advantages from these points of view: there are no known anomalies in the property changes accompanying precipitation; there are no known transition stages; the precipitate is an element, not a compound, and both matrix and precipitate are cubic, and while the structures are not identical (the solid solution is face-centered cubic and the precipitate is diamond cubic), the system at least approaches the ideal case of a crystal precipitating from a matrix of the same crystal type—the ideal case which Becker6 assumed in treating the precipitation process theoretically. The dilatometric method, while not free from disturbing effects, as the subsequent dis-

Jan 1, 1943

By Lawrence K. Jetter, Robert F. Mehl

Some advances have been made recently in the theory of the kinetics of precipitation from metallic solid solution despite the complexities of the problem, but there is surprisingly little quantitative information available on rates of precipitation with which to test present theory or upon which to build new theory. Attempts to measure rates of precipitation have been beset with difficulties which originate both in the anomalies that attend the changes in the properties selectcd for measurement, as, for example, in electrical conductivity or mechanical properties, and also in the complexities in the structural changes in some systems, as in the aluminum-copper system. If the functional relationship between the quantity of precipitate and the value of the selected property is uncertain, measurements of that property are obviously of uncertain utility in determining absolute rates of precipitation. If the precipitating system passes through one or more transition stages, the interpretation of measured rates lacks definiteness; in such cases, it is necessary to measure the rate of reaction in each separate stage, if the rate measurements are to have any significance from the kinetic point of view.* These difficulties cannot be wholly avoided, for at least in some measure they are characteristic of the process of precipitation from solid solution, but they can be minimized both by the selection of a simple system and by the use of a method of measurement relatively free from anomalous behavior. The present paper reports dilatome tric measurements on the rate of precipitation of silicon from the aluminum-rich solid solution in the aluminum-silicon system—a study that approaches the desiderata of simplicity. The aluminum-silicon system offers advantages from these points of view: there are no known anomalies in the property changes accompanying precipitation; there are no known transition stages; the precipitate is an element, not a compound, and both matrix and precipitate are cubic, and while the structures are not identical (the solid solution is face-centered cubic and the precipitate is diamond cubic), the system at least approaches the ideal case of a crystal precipitating from a matrix of the same crystal type—the ideal case which Becker6 assumed in treating the precipitation process theoretically. The dilatometric method, while not free from disturbing effects, as the subsequent dis-

Jan 1, 1943

By Irwin Roman

IN studying the possibilities of a continuously recording magnetometer for use along the surface of the earth and in an airplane, the Federal Bureau of Mines was led to a study of the theoretical resolving power of magnetic observations, both in the variation of the total magnetic intensity and in each of the two components ordinarily measured. Along with this general study, an attempt was made to determine the relative worth of the total intensity anomaly and the vertical anomaly in geophysical prospecting. General considerations led to three conclusions: I. In the northern magnetic hemisphere of the earth, the total intensity anomaly is offset to the south of the vertical anomaly, for a positive anomaly (see Appendix, note I). 2. The resolving power of magnetic observations decreases rapidly with distance from the disturbing body. 3. The horizontal anomaly has little value in prediction of the disturbing body but might be useful in making a choice between bodies suggested by the vertical or total anomaly. Some of the considerations leading to these conclusions were: I. The normal intensity and the anomalous intensity are vectorially additive; hence for a positive anomaly in the northern magnetic hemisphere the total intensity will be a maximum at some point south of the disturbing body and north of the point at which the line to the disturbing body is parallel to the normal earth's field. The anomaly itself has a maximum value directly above the body. For a positive anomaly of constant magnitude, the total intensity will be a maximum when the anomaly vector is parallel to the normal vector. This is shown schematically in Fig. I (not to scale) for a magnetic distribution not restricted to a relatively thin sheet in the magnetic meridian. The normal field has a magnitude Io with vertical component Vo and horizontal component H,. Six station points along a traverse' across the body from south to north are shown at M to S. At each of these stations the normal magnetic field vector terminates at F. At each of these stations the magnetic field vector due to the disturbing body B terminates at A. The line through the station point and the point A passes through B. The magnitude of the anomaly, indicated by the length of the vector terminating at A, is proportional to some power of the distance from the station point to the disturbing body. If the' disturbing body B is a concentrated point of magnetic material, the anomaly is proportional to the inverse second power of the distance. For a uniform magnetic distribution over a line perpendicular to the observed traverse, the anomaly is proportional to the inverse first power of the distance. For surface distributions, the law of intensity is more complicated. At each field point, the total magnetic intensity T is the vector sum of the

Jan 1, 1946

By E. V. Potter

For a nurnber of years, it has been known that manganese made by electro-deposition under certain conditions is ductile while under other conditions it is very brittle. The ductile metal is gamma manganese normally stable only between 1100 and 1138°C1; the brittle metal is alpha manganese, stable up to 727OC. The ductile metal is not stable, but gradually changes to the brittle form; the time required to complete the transfornlation is about 20 days at room temperature. Other observations have indicated that the transformation is completed in 10 to 15 min. at about 125°C, while at — 10°C, no appreciable change occurs in 9 months. The properties of gainma and alpha Illanganese in the pure state are ordinarilj difficult to determine because the gamma structure cannot be retained by normal quenching procedures and alpha manganese is so brittle, it is difficult to obtain specimens free from flaws. In a recent investigation2 some properties of gamma and alpha manganese were determined by studying the ductile electrolytic metal and determining the changes in its properties as it transformed to the brittle alpha form. These investigations provided an excellent opportunity for following the progress of the transition and studying its mechanism. The results of a series of such investigations are reported in this paper. Procedure Various properties of manganese were determined starting with the metal in the original ductile gamma form and following the subsequent changes in its properties as the metal transformed to the brittle alpha form. These observations were made at various temperatures, the data providing information regartling the mechanism of the transformation as well as the effect of temperature 011 the transition rate. Structure and resistivity values gave the most significant results, so this paper is concerned primarily with them. The structure was studied microscopically as well as by X ray diffraction. The resistivity was determined on strips of the metal by measuring the potential drop across a given length of the specimen. Current was passed through the specimen by wires soldered to its ends, and the potential connections were made by wires looped around the specimen near its center. The current was determined by the potential drop across a standard resistor connected in series with the specimen, the potential drop being measured on a potentiometer. In the temperature range from room temperature to 100°C an ordinary drying oven was used to heat the specimen. This was entirely satisfactory except at 100°C, where the time required to heat the specimen was long compared to the transition time, making the initial section of the resistivity curve unsatisfactory. To overcome this limitation, at 100°C and higher a thermostatically controlled oil bath was used to heat the specimens. The block on which the specimen was mountetl was plunged into the hot oil at the start of each test. The heating time was thereby reduced from 5 min. to about 6 sec, and dependable resistivity values could be obtained through 160°C. At this point the whole transition, including the warm-up time for the specimen, required only about 20 sec and it was not considered worth while trying to extend the temperature range further. Aside from the heating problem, the problem of making a sufficient number of accurate resistivity determinations became more and more difficult as the temperature was raised. Using the manually operated potentiometer, 100°C was about as far as it was possible to go. At this temperature and above, a self-balancing photoelectric recording potentiometer was used. Its response was quite rapid, and it proved to be entirely satisfactory all the way through 160°C, where the tests were stopped because of the specimen heating problem rather than any limitation of the potentiometer recorder. The metal used in these tests was prepared at the Salt Lake City laboratory of the Bureau of Mines. The method of preparation is discussed in a paper by Schlain and Prater.3 The sheets were about 2 3/8 by 5 3/16 in. and varied from 10 to 16 mils in thickness. They could be cut readily into pieces suitable for the various tests. X ray and microstructure determinations were made on pieces about 1/8 to 1/4 in. wide and about 1 in. long, while resistivity measurements were made on strips as long as possible and about 55 in. wide. The thickness of each sheet was not uniform over all its surface. This had no bearing on the X ray and microstructure determinations, but sections as nearly uniform and free from flaws as possible were chosen for the resistivity determinations. The gamma manganese was electro-deposited at 30°C, the time of deposition ranging from 5 to 12 hr for each sheet. Whenever possible, the tests were started directly after the metal was stripped from the cathode; otherwise the sheet was placed immediately

Jan 1, 1950

ABERDEEN, ESTHER, U. S. Geological Survey, Washington, D. C. ALLEN, VICTOR T., Director Geology Department, Institute of Technology, St. Louis University, St. Louis, Missouri. BATES, THOMAS F., Associate Professor of Mineralogy, Department of Earth Sciences, School of Mineral Industries, The Pennsylvania State College, State College, Pennsylvania. BOLGER, ROBERT C., Geologist, Pennsylvania Topographic and Geologic Survey, Harrisburg, Pennsylvania. BRIDGE, JOSIAH, U. S. Geological Survey, Washington, D. C. BURST, JOHN F., Geologist, Exploration and Production Research Division, Shell Oil Company, Houston, Texas. CAMPBELL, IAN, Executive Officer, Division of Geological Sciences, California Institute of Technology, Pasadena, California. FLINT, DELOS E., U. S. Geological Survey, Washington, D. C. FREDERICKSON, A. F., Associate Professor of Geology (Geochemistry), Washington University, St. Louis, Missouri. GLASS, HERBERT, Illinois State Geological Survey, Urbana, Illinois. GORDON, MACKENZIE JR., Geologist, U. S. Geological Survey, Washington, D. C. GRIM, RALPH E., Research Professor, Department of Geology, University of Illinois, Urbana, Illinois. HARDER, E. C., Aluminium Secretariat Limited, Montreal, Que., Canada.

Jan 1, 1952

By P. G. Shewmon

A novel technique for determining the surface energy (?) and its derivative with respect to orientation, (?') is described. Essentially it involves the 'floating" of a wedge on the substrate, said wedge being made of a material which is not wet or only slightly wet by the substrate, i. e., as a greased needle "floats" on water. A thermodynamic analysis of a system in which the wedge is supported entirely by surface energy is given. If the original suyface is not at a cusp orientation, the surface tension is directly measurable from the groove angle formed. If the original surface is at a cusp orientation, there may or may not be a groove depending on the relative value of ?' and the weight of the wedge. Experiments primarily on copper and silver showed that sapphire, quartz and refractory metal wedges were wet while graphite wedges were not. The technique was demonstrated to work using graphite wedges, but the results obtained were not as eccurate as those obtained by other workers using the wire-creep experiments. It is concluded that the technique might prove most useful with non-metals where ?' is large and filament creep experiments would be quite difficult. If an absolute value of the surface free energy (?) of a metal is to be determined, the most reliable methods used to date measure an average over the various orientations exposed on a polycrystalline sample. For example, ? for silver, gold, and copper have been measured by determining the force required to just keep a thin wire,' or foil,' specimen from contracting under the influence of ?. Herring 3 has predicted and experiment confirms, that the sensitivity of this method is inversely proportional to the grain size.' Thus it cannot be used to measure ? for a particular orientation by using a foil single crystal or a very coarse-grained specimen. An accurate value if ? for tungsten averaged over a range of orientations has been determined using a field emission technique. The same techniques cannot or have not been used to measure ? for non-metallic solids, and as a result the values available are much less accurate.4 This Paper resents a means of making an absolute determination of ? for a particular surface orientation on any solid, as long as the given surface orientation does not break up into other orientations during an anneal. Experimentally ? is found to vary with orientation and at a few low index orientations it is found to have a cusped minimum, i.e., the derivative of ? with respect to the orientation of the surface changes discontinuously at the low index orientation, see Fig. 1. The slope of a plot of ? vs orientation (herein designated ?') is called the torque on the surface, since it tends to rotate the exposed surface toward the low index orientation, or if the surface is at the cusp orientation it opposes any force tending to rotate the surface out of the low index orientation. The ratio ?'/? has been determined for a few metals, but in cases where this ratio is high there is presently no means of determining either ?'/? or the absolute value of ?' for the orientations present on an annealed surface. The technique discussed herein also provides a means of determining an absolute value of ?' for those orientations which deviate only infinitesimally from a cusp orientation. It should work best on surfaces where ?'/? is large; that is, for cases where no other technique is available for measuring ?'. Aside from trying to learn more about surfaces through measuring ? and ?', the primary reason for wanting values of ? or ?' is to study adsorption. From measurements of the variation of ? for a particular orientation with the concentration of an impurity, one can obtain the number of impurity atoms adsorbed per unit area (Ti) on that orientation using the Gibbs adsorption equation.' where µi is the chemical potential of the adsorbed impurity. Thus, if absolute values of ? could be obtained for the free surface of a given surface orientation as a function of µi, ri could be determined for the given orientation. Furthermore, by equilibrating a grain boundary with the given surface at various values of ki, one could also determine ri for the grain boundary. Similarly Robertson 6 has pointed out that if y is taken to be a continuous function of and µi, then a2 ?/a @a µ2 = a2 ?/a pi a +. Thus, at all orientations away from cusps the following equation holds From a measurement of ?' vs ki, it is thus possible

Jan 1, 1963

By GEORGE D. RAMSAY

ABOUT three miles west of Fontana San Bernardino County, California, and fifty miles east of Los Angeles, the Kaiser Co., Inc., has built an integrated steel plant. By integrated, I mean that from its wholly owned iron ore and coal supply, the Kaiser Co. is producing in its own mills iron and steel products. Pig iron to meet the West Coast needs has been produced at Fontana since Jan. 1, 1943; steel ingots were first poured there May 14, 1943; and steel plate for ships was first rolled Aug. 15, just sixteen months after ground was broken. Briefly, the plant consists of: (I) Two batteries of by-product coke ovens, totalling ninety ovens, carbonizing about 1740 tons of coal per day at capacity; with by-product facilities for the production of tar, ammonia, and ammonium suIphate, light oil distillates, and tar distillates. (2) One blast furnace producing at

Jan 1, 1944

By Arthur F. Taggart

MR. CHAIRMAN: Congratulations! Your four-ring milling show this year was a dandy. It cleared our minds, for a few hours at least, of what Hitler, Hirohito, the New Deal, and the tribe in the Treasury are trying to do to strangle American enterprise. We mustn't forget this, but it's a relief to get our thoughts away from it occasionally. GRINDING-There was a further contribution to the excellent work that the Allis-Chalmers laboratory staff has been doing for the grinding fraternity in compiling-and publishing-a carefully quantitative list of comparative resistances of ores and other materials to comminution (T.P. 1579, Bond-Maxson). A diagnostic accuracy of ± 10 per cent was claimed for estimates based on these figures. Are they really that good? How about some of you men in the field writing M&M about it?

Jan 1, 1943

By Earl S. Bardwell

In his paper entitled, Development of Hindered-Settling Apparatus, Dr. Richards has related the history of the development of the hin-dered-settling classifier and given illustrations of the several types of this apparatus which he has designed.' An earlier paper,2 Close Sizing Before Jigging, shows the nature of the hindered-settling phenomenon and the results which it produces. In the first-mentioned paper Dr. Richards describes the method of getting hindered settling and shows the relation that the constriction bears to the classifier. The question of proper ratios between the area of the sorting column and the area of the constriction opening Dr. Richards leaves open, aside from certain statements as to the ratios which have been found to give good results in practice. While working with a hindered-settling classifier of the type now in use at the Boston & Montana Reduction Plant of the Anaconda Copper Mining Co. a number of interesting facts were brought out which have thrown considerable light on the question of proper ratio between the area of the sorting column and the area of the constriction and which will be made the subject of this paper. Free and Hindered Settling.—If a mineral particle be dropped into a vessel containing still water, the particle will sink in accordance with the laws of free settling in water, which are as follows: 1. Of two grains having the same specific gravity but differing in size, the larger will settle in still water at the greater velocity. 2. Of two grains having the same size but differing in specific gravity, the heavier grain will settle at the greater velocity. From these laws it becomes evident that the velocity of settling depends primarily on the specific gravity and the size of the mineral grain. The fracture of the mineral may exert a very considerable

Jan 1, 1914

By C. A. Bruch, J. F. Duffey

On the basis of metallographic and cooling-rate studies of 15 U-Zr alloys, a new version of the 6 phase region of the U-Zr phase diagram is proposed. IN several published diagrams of U-Zr alloy system:' there is good agreement that at elevated temperatures complete solid solubility exists between y uranium and ß zirconium. Similarly, there is reasonably good agreement concerning the uranium-rich and zirconium-rich ends of the diagram. However, there is no agreement concerning the nature of the diagram at intermediate compositions and at temperatures below about 650°C. The early work of Saller et al.8 hows an intermediate phase, 6. In a later diagram by Saller and Rough' shown in Fig. 1, the d phase field is drawn with dotted lines, indicating doubt that this phase exists. The diagram of Summers-Smith2 does not show the d phase. More recently Holden and Seymour' have shown that in the composition range 40 to 60 wt pet Zr, the high-temperature ? phase, which is body-cen-tered-cubic, transforms to an ordered structure, 8. They found that the order-disorder transformation occurs between 595° and 610°C, and presented a diagram based on the study of four different alloy compositions. Most recently Saller et a1.5 presented a new diagram which differs with respect to the composition limits of the 8 field from the others proposed by these authors. The purpose of the present investigation was to determine the boundaries of the d phase field. Experimental Procedures and Results Alloys—Buttons, weighing 80 g of 15 different alloy compositions were prepared by arc melting Mal-linckrodt uranium and iodide-process zirconium in a water-cooled crucible. A controlled atmosphere of argon and helium was maintained in the furnace. Prior to making each button, a sacrificial button of zirconium was melted to increase the purity of the furnace atmosphere. Each alloy was then melted six times to improve its homogeneity. Subsequently the alloy buttons were jacketed in copper and hot rolled to slabs at 775°C. From these slabs, specimens were machined for chemical, thermal, and metallographic analyses, Table I gives both the estimated chemical composition of the alloys, and the values which were obtained by analysis. The oxygen contents varied from 0.013 to 0.032 pet, nitrogen from 0.0014 to 0.014 pet, and carbon from 0.0013 to 0.011 pet. The purity of the alloys ranged from 99.947 to 99.975 pet. Thermal Analysis—The specimens for thermal analysis were blocks 11/4 x 1/4 x % in. The bead of a calibrated thermocouple was placed between two of these blocks and molybdenum wire was wrapped around the assembly. Each assembly was sealed in a quartz capsule having an argon atmosphere. The capsule was placed inside a refractory crucible which was heated in a furnace. Using a method described by Smith,' the emf of a differential thermocouple, with junctions inside and outside of the refractory crucible, was used to activate the

Jan 1, 1959

ON FEBRUARY 4, 1952, the Phelps Dodge Corporation signed Contract GS-00P(D)-12068 with the United States Government. This interesting document dealt with the "Bisbee East" project as part of the Government's program to increase the supply of needed copper by encouraging private enterprise to expand production. The ore deposit involved was a relatively small body of low-grade ore lying east of the remnants of the old Sacramento Hill deposit that was exploited with indifferent success from 1923 to 1931, as related in THE PORPHYRY COPPERS. Planning for the entire enterprise had been directed from the start by Harrison M. Lavender, who in 1945, succeeded Percy G. Beckett as vice-president and general manager for all of Phelps Dodge's Western mines and smelters. The untimely death of Mr. Lavender in 1952 prevented him from seeing his plans brought to fruition; but in his honor the mine was fit- tingly named "The Lavender Pit" and was so dedicated on August 7, 1954. The Copper Queen Branch operates under- ground mines at Bisbee (production in 1955 was 28,000 tons) ; but, as this volume is concerned only with Porphyry operations, this chapter deals only with the Lavender Pit project, or as the Government knows it, Bisbee East. My reason for going into some detail regarding the floor-price contract is that it is fairly typical of contracts made by the Government in connection with a half-dozen other copper-expansion projects; and, incidentally, with various projects involving other strategic metals. Phelps Dodge did not seek a loan or other financial aid. The only encouragement asked consisted of (a) the privilege of a five-year write-off (commonly called rapid tax amortization)

Jan 1, 1957