Search Documents

By R. S. French, W. R. Hibbard

FOR tensile deformation, if the stress value is defined by the ratio of the load to the actual area, and the strain value by the natural logarithm of the ratio of the immediate length to the original gauge length of the sample, the resulting data when plotted with logarithmic coordinates result in a linear relation extending from the initial plastic yielding through the maximum load and in some cases, such as for copper and brass, to fracture'.'. The normal form of the curve, therefore, is a parabola, satisfying the following equation: S = Kem [1] where S and e represent true stress and strain, K is a constant, and m is a coefficient evaluating the slope of the curve and designated therefore as the strain hardening coefficient. Hollomon² has reported that this coefficient is a function of the yield strength as effected by grain size in alpha brass, and the carbon content and heat treatment of steel. In the case of steel, the value of the proportionality constant is a function of the carbon content. It was further shown in that paper2 and also by Low and Prater -hat, if the power relation between stress and strain remains valid, the strain hardening coefficient m, is equal to the strain at the maximum or necking load. Thus, an added significant feature is that this coefficient may serve as an index of the capacity for deformation prior to localized necking and subsequent fracture, e.g. drawability. The constant K may be defined as the strength of the material at unit strain. Together the K constant and the m coefficient describe an alloy's physical properties as far as strength and ductility are concerned for a particular yield strength and, in the case of steel, a particular carbon content. The work of Lacy and Gensamer4 gives data on alloy ferrites from which very close estimates of the strength of ternary and higher iron alloys have been made. It was the purpose of this investigation to develop similar data for commercial copper base alpha solid solution alloys. Preparation of Specimens Commercial binary alloys of copper with aluminum, beryllium, cadmium, nickel, silicon, tin and zinc were investigated. In addition, laboratory castings were made of a 1 pct silicon alloy and a 2 pct aluminum alloy to complete these particular series. Two types of copper were used, oxygen free OFHC and tough pitch FC. The analyses of these alloys are shown in table I. Standard ASTM sheet tensile specimens were used to determine the usual physical properties of each alloy and to obtain stress data at strains from 0.0005 to 0.01. Small (1/4 in. x 3 in. x tk.) samples

Jan 1, 1951

By G. W. Thomas

Jan 1, 1967

Jan 1, 1970

By C. E. Sims

THE following presentation is more a summation of observations made and conclusions drawn over a period of three to four years than a report of experiments made with a definite objective. Tests were made, of course, to verify hypotheses, but the large mass of data was collected incidental to other work. Lack of space forbids the presentation of more than a few of those data. On the other hand, it is unfortunate that some of the most illustrative examples are not available. The work is admit¬tedly incomplete but is presented in the hope that it will stimulate further work along a similar line. The answers to many of the questions left unanswered by this paper will be found only after long and painstaking study, such as is scarcely possible in a commercial laboratory where problems of immediate importance consume most of the time. It is also hoped that this study will in some measure throw light on some of the dark spots of steelmaking, and help to clarify some of the annoyingly vague references to "good practice." Only cast steel was studied and the conclusions apply to cast steel, but it is the authors' opinion that the quality of rolled or forged steel is largely dependent on the quality of the ingot, which is a casting. Although this discussion deals almost entirely with inclusions, it is important that the reader understand that only those natural inclusions which owe their origin to the solubility of certain materials in steel and to the chemical reactions of steelmaking are considered. Accidental inclusions, such as entrapped particles of slag, nozzle, runner, or mold are outside its province and are not considered. Such accidental inclusions are always dangerous and should be carefully avoided.

Jan 1, 1932

By A. M. Gaudin, J. H. Brown

In a survey of the effects of heat treatment on the comminution of various rocks, it was found that unusual size distributions often characterize the broken products, and that this is related to a great increase in intergranular fracture1. It is the purpose of the present paper to contribute to an understanding of this effect. In a thesis by one of use, critical consideration was given to many mechanisms which could conceivably be responsible for the increased intergran-ular fracture. It was shown that neither gross chemical changes nor intergranular corrosion are required. Among non-chemical mechanisms the most likely appeared to be (1) Uneven expansion due to thermal gradients, giving spalling (2) In a manner similar to that prevailing in metals, the appearance at high temperature of intergranular weakness. (3) Unequal thermal expansion of adjacent grains. Experiments were designed and conducted to permit a choice among the many alternative mechanisms and in particular among the three listed here. EXPERIMENTAL MATERIALS Tests were made on the materials listed in Table 1. Of each material, only lumps similar in composition and grain size were used. The three marbles listed in Table 1 were analyzed to assure that their chemical compositions did not differ greatly (Table 2). On the basis of the chemical analyses, of differential thermal analyses, and of X-ray powder diffraction patterns, it appeared that the marbles were very similar except for their grain sizes.

Jan 1, 1961

By H. Kazemi, M. S. Seth

The effects of anisotropy and stratification on flow behavior and production performance of oil and gas wells have been studied by numerous authors.1-3 Lefkovits et al.l studied the performance of totally penetrated, stratified bounded reservoirs with no crossflow. Others have studied a similar problem, but with crossflow; Russell and Prats2 have summarized the findings of these papers. Muskat3 studied the steady-state behavior of liquid flow for a partially penetrating well in an anisotropic system and concluded that the productivity weakly depended on the directional permeability ratios (kz/kr>0.1). Nisle4 used the classical method of point source solution to the diffusivity equation to study the effect of partial penetration on pressure buildup of oil wells in an isotropic system. He found that the theoretical pressure buildup curves consisted of two straight lines, the one at early buildup times having a slope proportional to the flow capacity of the open interval (l-d)k, and the other having a slope proportional to the flow capacity of the entire formation hk,. Later Brons and Marting5 supplemented the findings of Nisle and concluded that partial penetration gave rise to a pseudo damage, which reflected itself as a skin factor in pressure buildup calculations. Using the pseudo skin, they calculated the impairment of productivity of the production wells, which agreed well with the results of Muskat.6 Pizzi et al.,? using an electrical analog of a stratified system, concluded that a high pseudo damage resulted if the reservoir was partially penetrated. Harriss studied the optimum spacing and arrangement of perforations in cased holes. Hantush9 derived an expression for pressure distribution in an unbounded reservoir with restricted flow entry. Seth10 extended Hantush's work to a bounded reservoir. Odehl1 has studied a similar problem for steady-state conditions. The purpose of this work was to investigate: (1) the combined effects of anisotropy, stratification with crossflow, and restricted flow entry on pressure transient analysis of flow and buildup tests, (2) the feasibility of calculating the horizontal permeabilities of intercommunicating stratified systems, and (3) the pressure interference tests in such systems. Theory The partial differential equation governing the isothermal flow of homogeneous fluids of constant compressibility is given by Eq. 1: The initial and the boundary conditions are: 1. The reservoir potential is initially constant, say 4v

Jan 1, 1970

By Max Roesler

I. INTRODUCTION THE following article concerns the geological occurrence of the iron-ore deposits on the south coast of Cuba. The article is based on a detailed field study, made in the hope that some information would I gained which might be of value in the search for further orebodies, Or in the economic development of the ore already found. LOCATION The iron-ore deposits of the Firmeza district lie near the coast, in the southeastern part of Cuba, in the Province of Oriente. The orebodies of this district form part of a belt of deposits that extends from Sigua, 25 miles east of Santiago, to Sevilla, 5 miles east of Santiago, and lies on the seaward slope of the Sierra Maestra range of mountains.

Jan 10, 1916

Jan 1, 1971

By D. M. Davidson, P. F. Kerr

The Permian Cutler Formation in Kane Creek, Utah bears uranium ore in fissure-type vertical veins. This fissure vein formation and its associated host rock bleaching, weak argillic alteration, and base-metal sulfide mineralization along with the development of hydrothermal minerals, a 60 m.y. isotopic Pb/U age, and well-crystallized uraninite's structural control, give evidence of ore deposition in a hydrothermal environment consistent with Laramide mineralization. Mica polymorph studies indicate first, that temperature during the hydrothermal alteration or subsequent ore deposition did not exceed 200°; hence Cutler deposits are classified telethermal; and secondly, that rock alteration and ore deposition are closely related both in time and space, as is seen in argillic alteration sequence. Ore deposition in an alkaline to slightly acid reducing environment is postulated. Ore textures and mineral associations and distributions also indicate that carbonate complexes may have been transported with the deposing ores. Bleached rock formations are not primary strati-graphic phenomena. Bleaching, or changes in ferric iron content, results from a chemical process involving reduction and conversion of hematite to a soluble aqueous ion. Nearby Chinle bedded deposits (Moss Rack sandstone), containing shale lenses, fossil wood, organic debris and minor fractures, overly the Cutler formation. Chinle ores have a single reported isotopic age of approximately 200 m.y. Their chemical environment is assumed similar to that of the Cutler ores, though slightly more acidic. Two genetic, paradoxically divergent interpretations of the bedded deposits are derived from available spectrographic, petrographic, X-ray and chemical analyses. Kane Springs canyon is located southwest of Moab, Utah, south of the Colorado River and northwest of the Lisbon Valley mining district (Fig. 1). Uranium deposits occur along the northeast flank of a Kane Creek salt anticline where two geologic formations bear ore, the Permian Cutler and the Triassic Chinle. The Cutler deposits' fissure vein formation is an unusual occurrence in the Colorado Plateau. The Chinle deposits appear to be of the normal sedimentary type. Associated with the vein deposits are a number of features, including argillic alteration of sedimentary strata. The minerals of these deposits and their associated features have been studied in detail in a two year program entailing both field and laboratory techniques. STRATIGRAPHY A stratigraphic section of the lithologic units in the Kane Creek area is given in Table I.

Jan 1, 1967

By I. Cadoff, E. Miller, K. Komarek

Jan 1, 1960

By George M. Fowler

EVERY year it becomes more difficult to find new mining districts and new ore deposits. Nearly all of the important discoveries so far can be attributed to surface manifestations overlying the ore deposit. In the future greater skill will be necessary to find ore deposits that give little or no indication of their presence. Mining geology is making progress by broadening its attack upon mineralized regions, by including in its investigations studies of the relation of physical-chemical processes to ore precipitation and various phenomena that heretofore have not always been looked upon as major factors in the problems. Such, for example, are petrographic peculiarities that will help determine structure, aspects of strata or formations favorable or unfavorable to structural deformation or mineralization, and renewed studies of chert and dolomite. This broadening attack is not necessarily being directed to the study of large areas, but rather by doing extremely detailed work in three dimensions in relatively small critical areas to find the key to the structure, reasons for the manner of rock deformation, composition and texture of the rock, and other con¬trolling factors in the larger areas.

Jan 1, 1935

By Barry D. Lichter, Pierre Sommelet

High-temperature heat contents of InAs and GaAs were measured over the temperature range 400°K to temperatures above the melting points using a di-phenyl ether drop calorimeter. Smoothed values of the thermal properties have been derived and tabulated at even temperature interuals . The heats of fusion of InAs and GaAs were determined as, respectively, 8790 ± 200 and 12,590 ± 300 cal per g-atom at the respective melting points of 1210º ± and 1513º ± 1°K, yielding entropies of fusion of 7.26 * 0.16 and 8.32 ± 0.20 cal perºK per g-atom, respectively. A general discussion of the thermal properties of III-V com-pounds is given. THE low-temperature heat capacities of InAs and GaAs have been determined by Piesbergen.1Using a dynamic temperature modulation technique, Miller2 has determined the heat capacities of the compounds as well as GaSb and Ge between room temperature and 650°K; however, it has been observed that values determined by drop calorimetry for GaSb3 and for germanium4 are consistently about 5 pct lower than Miller's results. Cox and Pool10 report values for the heat content of InAs and GaAs and the heat of fusion of InAs. No value for the heat of fusion of GaAs appears to have been previously reported. This paper reports results of high-temperature heat content investigations of InAs and GaAs measured in the range 400" to above 1500°K employing a diphenyl ether drop calorimeter. These results, together with our previous results on III-Sb compounds3 as well as heat-content measurements5 of solid InP and Gap, are used in a general discussion of these compounds. EXPERIMENTAL PROCEDURES High-purity samples of the compounds, stoichio-metric to ±0.1 at. pct, were supplied in the form of crushed crystal fragments by Dr. Carl Thurmond of the Bell Telephone Laboratories. The sample preparation, description of the calorimeter, and details of the heat content measurement have been previously described.3 Samples were sealed in evacuated silica capsules and suspended by a Pt-Rh wire in a Pt-wound vertical tube furnace, heated to temperature

Jan 1, 1970

By George Weaton

Two years ago the general features of the St. Joseph Lead Company's zinc-smelting process were described.1 At that time the discussion was limited to a description of the production of high-purity electrothermic zinc oxide. The present paper will describe the commercial production of electrothermic zinc metal. Since a fairly complete description of the plant of the Josephtown smelter was given in the earlier paper, the brief recapitulation given here will be limited to mention of additional equip-ment recently installed and a bare outline of the preparatory process. The raw material is zinc sulphide concentrate received from the com-pany's mines in St. Lawrence County, New York. An average dry-weight analysis of this material is: Zn, 58.28 per cent; Pb, 0.56; insoluble, 1.6; Si02, 1.12; Fe, 6.4; CaO, 0.47; MgO, 0.27; S, 31.9; Cd, 0.1; Cu, 0.06; Mn, 0.24. Moisture content is usually about 3 per cent. Three 21-ft. 6-in. diameter, 12-hearth Nichols-Herreshoff furnaces roast the concen-trate to a calcine of average composition (first 10 months of 1938) : Zn, 67.69 per cent; Pb, 0.06; insoluble, 1.75; Si02, 1.26; Fe, 7.24; CaO, 0.47; MgO, 0.36; S, 1.88; Cd, 0.1; Cu, 0.07; Mn, 0.27. The sulphur dioxide gas, after passing through a waste-heat boiler, proceeds through a recently redesigned low-resistance gas-purification assembly to the contact sul-phuric acid plant, of which the capacity is 200 tons of concentrates per day. The calcine is mixed with a portion of returned furnace residues and sintered on 42-in. by 44-ft. Dwight-Lloyd sintering machines, gas-fired. Wind-box gases pass through air coolers before filtering in a 1440-bag Dracco unit, and thence to stack. The Dracco fume is mixed with Cottrell dust, from roaster gas cleaning, and sent to the leach plant, where it is roasted (SO2 to acid plant) and leached with sulphuric acid to recover, as end products, lead sulphate, zinc sulphate and cadmium.

Jan 1, 1939

By R. W. Raymond

WISH to call the attention of the Institute to a curious subject, brought to my notice last summer by Mr. Begger, the accomplished metallurgist of the smelting-works of the Boston and Colorado Company at Black Hawk, near Central City, Colorado. At these works, the richest auriferous sulphhrets of Colorado (particularly copper pyrites) are smelted in reverberatories, together with roasted tailings (iron pyrites), and the gold and silver are concentrated into a new, artificial sulphide, or copper matte, containing $1500 and upwards of the precious metals per ton, and this is shipped to Swansea. I will say in passing, that this shipment of an unrefined product, like the similar shipments from Utah and Nevada to San Francisco, Chi¬cago, St. Louis, Newark, New York, and Europe, of crude argentiferous lead or "base bullion," is not a sign of incomplete metallurgy here, but has a sound business reason. The separation of the precious metals in the West would be more expensive, to begin with ; and then it would necessitate the movement of these metals by express, at high rates and risk, to commercial centres or coining mints, while the base metals having no home market, must be shipped and sold at little or no profit. At present, the gold and silver, safely packed, as it were, in the base metals, are transported with safety as ordinary freight; and the base metals probably more than pay cost of shipment and separation. To return to the Black Hawk reverberatories. On a recent occa-

Jan 1, 1873

By W. C. Maurer

A study of the mechanics of shear failure of rock under pressure has been made. The transition from brittle to ductile failure occurs when the friction along the fracture surfaces exceeds the shear strength of the rock. A machine has been developed for measuring both the shear strength of rock and the friction along rock fracture surfaces. In this shear machine, the fractures are forced along definite planes; as a result, the rock is stronger than in compression tests where the fractures choose the weakest paths through the specimens. Friction is composed of several forces: (1) the forces to slide irregulurities on surfaces over each other; (2) forces to shear some of these irregularities; (3) molecular attractions across the fractures; and (4) forces required to break bonds resulting from melting and welding at the tips of irregularities on the surfaces. Friction along rock fracture surfaces is not proportional to contact pressure as usually assumed; instead, it increases as the contact pressure raised to the 0.4 to 0.8 power. INTRODUCTION It is difficult to produce tensile stresses under the high compressive stresses present in the earth; therefore, in deep drilling and geological faulting, shear failure predominates. This shear failure mechanism is complicated because rock is a heterogeneous material containing pore spaces, microfractures, elastic discontinuities and other imperfections. A study of shear failure of rock under pressure has been made to obtain a better understanding of this complex mechanism. A machine has been developed and used to measure the shear strength of rock and friction along sheared surfaces. This machine has certain advantages over the compression test — shear properties can be measured under low normal stresses and shear stress and normal stress can be varied independently. The first part of this paper is a description of shear failure of rock under pressure. The role of shear strength and friction along fracture surfaces in the shear failure mechanism will be discussed. The second part consists of a description of the shear machine and a discussion of the shear strength and friction data obtained using this machine. It will be shown that shear strength depends upon the size of the stressed zone, and that friction does not increase linearly with contact pressure as usually assumed. Attempts are made to relate some of the new concepts to tectonic failure and to dril ling. SHEAR FAILURE IN ROCK TRIAXIAL TESTS The shear failure mechanism is illustrated by the triaxial test shown in Fig. 1. In this test, a cylindrical rock specimen is subjected to a confining pressure, PC, and an axial pressure, pa. These external pressures produce normal a and shear T stresses on inclined planes within the specimen equal to1 where 0 is the angle between the specimen axis and a normal to the inclined plane. Fig. 2 shows how triaxial specimens deform as the axial pressure is increased. The pressure is

Jan 1, 1966

By E. J. Ripling, M. W. Toaz

Tensile tests were conducted on pure magnesium and on four commercial alloys over a variety of temperatures and strain rates. The high positive slope of the ductility vs testing temperature curves that is found over a short range of testing temperatures for these materaturerials was shown to result from the fact that the microstructure was not stable at these testing temperatures. Pure magnesium did not display a transition temperature, although its sub-room temperature ductility was low. This poor ductility resulted from a grain boundary weakness. The aluminum-bearing commercial magnesium alloys had a higher ductility than the pure magnesium. ness.Thealuminum-bearingcommercialThese alloys did exhibit a transition temperature and grain boundaries that were stronger than the grain material. Both pure magnesium and the commercial alloys began initiating cracks at strains equal to one half of their fracture strain. MAGNESIUM base alloys' enormous potential as structural materials lies in their high strength to weight ratios. At present, the high strength magnesium base alloys such as AZ-80, which will be discussed later, have about as high a tensile strength to specific gravity ratio as the highest strength wrought aluminum alloy, 75s-T6, and, of course, a much higher strength to weight ratio than structural steel. Further, since the magnesium base alloys develop their high strength to weight ratios with moderate strengths and extremely light weights, the ratio of load carrying capacity to the weight of many structures is relatively higher for the magnesium base alloys than their strength to weight ratios would indicate. This results because judicious increases in section size, such as increasing the depth of bending members or adding reinforcing ribs, can frequently increase the weight of a structure linearly while the strength and stiffness increase as the second or third power of the added weight. Strength and rigidity must be designed into lightweight structures by those techniques which establish multiaxial stress states. Consequently, strong, lightweight structures frequently also possess a greater propensity toward brittle failures. In order to insure against these catastrophic failures, an extra premium must be placed on ductility and toughness in light alloys. Current knowledge of the ductility and toughness behaviors—notched behaviors—of magnesium base alloys is limited.* Most of the magnesium base alloys * The state of present knowledge regarding the effect of testing temperature on mechanical properties has recently been summar-ized by Pritchard.' crystallize in the hexagonal system, so that they are expected to exhibit a tough and ductile to brittle transition temperature. Actually, a transition temperature behavior has been reported for commercially pure magnesium in the literature, but the characteristics of this transition temperatureh uggest that it may not be a transition in the usual meaning, but simply the onset of some thermal softening, a performance much like that which face-centered-cubic lead might exhibit slightly below room temperature. If transition temperatures do exist, such important questions as the manner in which they are affected by internal variables such as chemical composition and grain size, or the effect of external variables such as rate of straining or notch severity have never been investigated. The investigation reported upon herein was undertaken in order to define some of the mechanical behaviors of the magnesium base alloys better, to gain a better understanding of the influence of some of the above listed variables, and particularly to understand their effect on ductility and toughness better. Material and Procedure Material-—Pure magnesium and four commercial alloys were used in this investigation. The alloys were selected so that chemically they made up a series with approximately the same minor alloying

Jan 1, 1957

By H. Conrad

The strain hardening associated with the creep of magnesium single crystals at room temperatu.Je was investigated by shear tests in which the direction of stressing was reversed a number of times after creep in a <100> direction. The strain hardening was strongly anisotropic; the largest amount occurring in the direction of flow and the least 180 deg to this. The time law for creep changed from a parabolic type to logarithmic for the first and subsequent reversals of stress. For a given stress the creep strain decreased significantly for the first and second reversals and then only slightly for subsequent reversals. The logarithmic creep constant a changed in a similar manner. A linear relationship was observed between the creep strain for a given reversal and the stress. The slope for the third reversal yielded a strain hardening coefficient 12 to 16 times greater than that observed for unidirectional flow. Al-though no recovery was observed upon resting at room temperature, the hardening resulting from stress reversals could be completely removed by heating to 450" C. PREVIOUS work1.&apos; indicated that the creep rate of magnesium single crystals tested in the temperature range of 78" to 364°K decreased with time. This was attributed to an increase in internal stress resulting from an accumulation of dislocations at internal obstacles. The object of the present investigation was to further evaluate the nature of this hardening by conducting tests in which the direction of stressing is changed after previous creep in shear in a given slip direction. Previous to 1950 three investigations indicated that a Bauschinger effect3 occurred for single crystals as well as polycrystals brass in tension compression,

Jan 1, 1960

By L. H. DeWald

During the examination of various commercial brands of copper wire bars, which had exhibited different degrees of adaptability for being drawn into fine gages of wire by the present-day high speed machine, it was found that each brand had a more or less characteristic crystal macrostructure. The extremes of these macrostructures are similar FIG. 1.-EFFECT OF METAL TEMPERATURE IN CASTING ON CRYSTAL MACROSTRUCTURE OF BAR. Reading from left to right, metal temperatures were 1166" C., 1149" C., 1132" C.. 1121" C., 1093" C. to the maximum variation shown in the photomacrographs reproduced in Fig. 1. As the various brands did not differ materially in chemical composition, it was concluded that the differences in structure were the result of variations in casting technique.

Jan 1, 1931

By AIME AIME

THE John Fritz Medal Board of Award, at its annual meeting on Jan. 21, 1921, awarded its gold medal and diploma to Sir Robert Hadfield for the invention of manganese steel. On June 1, announcement was made that the Board of Award had awarded its gold medal and diploma to Charles Prosper Eughe Schneider for "achievement in metallurgy of iron and steel; for development of ordnance, especially the 75-mm. gun, and for notable patriotic contribution &apos; to the winning of the war." The award to Sir Robert Hadfield is for the year 1921; the award to Mr. Schneider is for 1922. The latter was made at this time in order that the medal might be presented by the group of American engineers now visiting England and France.*

Jan 1, 1921

By H. Kazemi, G. W. Thomas, M. S. Seth

The double-porosity model of Warren and Root7 for examining pressure drawdown and buildup phenomena in naturally fractured reservoirs has been extended to intetpret interference test results. Both analytical and numerical solutions are presented. The practicality of some of the assumptions in the Warren-Root model was also investigated. The standard procedure for interpreting interference tests in naturally fractured reservoirs beretofore employed an equivalent homogeneous reservoir model. A comparison of our results with the equivalent homogeneous model indicates the latter is inadequate for early time responses. For late time responses, however, the simpler equivalent homogeneous model yields favorable results. Finally, the effects of well spacing and the magnitude of the interporosity flow parameter are briefly cited. INTRODUCTION Interference tests can be used to provide reservoir information not obtainable from conventional pressure drawdown and buildup tests. The technique involves measuring the response in one or more wells arising from a pressure perturbation introduced into another well. It has been. successfully applied to single-layer, homogeneous, unfractured, isotropic and anisotropic formations to arrive at values of well storage capacity and a measure of directional permeability.l The techniques of interference testing usually can be extended to heterogeneous systems, provided the permeability contrast between any existing rock layers is not excessive.9 In such cases, the practical interference effects in an observation well of an interconnecting heterogeneous reservoir can be predicted using an equivalent homogeneous model. The calculated properties are then average values. Russell and Prats2 have demonstrated the utility of this approach for a single-phase, two-layer system. For naturally fractured reservoirs, some different approaches usually are necessary. The major departure from homogeneous or nearly homogeneous reservoir treatment is to characterize the fractured system as an entity having "double-porosity"; namely, we suppose the existence of both primary and secondary porosity, where the former is contained within a systematic array of identical rectangular matrix blocks and the latter is contained within an orthogonal system of continuous, uniform fractures (see Fig. 1). It is sufficient to assume that the permeability of the rock matrix is so small that movement of reservoir fluids to the producing wells is entirely through the fracture network. This assumption has been validated by Barenblatt3 and .employed by others?-7 Warren and Root7 used the double-porosity model to develop an interpretation of pressure drawdown and pressure buildup tests in naturally fractured

Jan 1, 1970