Search Documents

By John Henry Harden

THIS shaft, located in the northern anthracite coal-field about 2300 feet southwest from the court-house at Wilkes-Barre, in the County of Luzerne, Pa., is the property of the Lehigh & Wilkes¬Barre Coal Company. The sinking and cribbing to the solid rock (see isometrical view on Plate IX) was conducted by Mr. W. W. Kenrick. Dimensions of the earthwork to the foundation of the cribbing, 51' 1/2" long, 17' 4" wide, 31' deep. Total amount of excavation in cubic yards, 998.5. Dimensions within the permanent cribbing, 45' 4" long, 11' 16" wide, 31' deep, divided into six parts by buttons 8" x 12", each division, 7' x 11’ 16". Permanent cribbing 12" x 12"; temporary cribbing 8" x 10"; backing, 3" thick ; clay puddle to ex¬clude surface water, 12" thick; conductors, 8" x 5"; lining, 1" thick from top to bottom of the shaft. In the latter part of the year 1871, Mr. H. Murray & Son contracted with the company for the continuation of the work at the rate of four hundred dollars per yard in depth, to a point 100 feet below the Hillman seam of coal ; for the succeeding 100 feet the price to be increased twenty-five dollars per yard, and so on until the bottom rock of the Baltimore seam of coal was found. The size of the shaft within the cribbing timbers is 45 feet 4 inches by 11 feet 6 inches, having six divisions of equal dimensions, 7 feet by 11 feet 6 inches, giving room for what is known as the" standard diamond" car, whose capacity when level full is 100 cubic feet, but when loaded by the miner 4 inches above the top contains 112 cubic feet.* Two divisions of this shaft are intended for hoisting coal from the Hillman seam, two from the Baltimore seam, one for ventilation, and one for pumps. The works were planned for two pairs of direct-acting, high-pres¬sure engines, twenty-four boilers, and for an estimated output of 2500 tons of coal per day from the two seams. * Size of the "standard diamond" car, 8' 10” x 4' 3" x 2’ 8” = 100.1.4; loaded 4 inches above the top, 8' 10” x 4’ 3” x 3’ “0"= 112.7.6.

Jan 1, 1877

[The following discussion, comprising both remarks made at the Chicago meeting and contributions since forwarded to the Secretary, is based upon the following papers, presented at that meeting : "Segregation and its Consequences in Ingots of Steel and Iron," by Alexandre Pourcel, Paris, France. (See p. 105, mans. xxii.) " Microscopic Metallography," by F. Osmond, Paris, France. (See p. 243, Trans. xxii.) " Microstructure of Ingot-Iron in Cast Ingots," by Prof. A. Martens, Berlin, Germany. (See p. 37.) " Microstructure of Steel," by Albert Sauveur, South Chicago, Ill. (See p. -546, Trans. xxii.) "Farther Observations on the Relations Between the Chemical Constitution and Physical Character of Steel," by William R. Webster, Philadelphia, Pa. (See p. 113.) "The Heat-treatment of Steel," by H. M. Howe, Boston. Mass. (See p. 466.) Since all these papers were considered together, no attempt has been made to separate the discussion strictly under the several heads.] William R. Webster, Philadelphia, Pa.: I desire to say that in my first paper (Trans., xxi., 766) the actual ultimates were subtracted from the estimated ultimates, whereas in the paper submitted at this meeting the estimated ultimates are subtracted from the actual, thus giving contrary signs. The latter method corresponds with the direct effect. of low and high finishing-temperatures ; that is, a plus difference indicates low, and a minus difference high, finishing-temperature. I make this explanation to prevent confusion in comparing the two papers. Mr. Sauveur has shown that there is a close relation between the size of the grain and the ultimate strength, and also that the size of the grain depends on the temperature at which the material is finished in rolling, and on the chemical composition of the steel. I have shown that there is a close relation between the chemical

Jan 1, 1894

By W. A. Koehler, W. L. Eaton, Reynold Q. Shotts, M. E. Hinkle, M. R. Geer, Ralph M. Hunter, H. F. Yancey, Andrew B. Crichton, E. Zimmerman, S. H. Ash

R. Maize and H. P. Greenwald presiding) E. T. POWELL*-I would like to ask either Mr. Ash or Mr. Eaton if they know of any place where the Mine Inspectors' for¬mula has been used that water has flowed from one colliery to the other. W. L. EATON (authors' reply)-We have made considerable study but we have not gotten around to very many of the barrier pillars. I would not say that any or all of them have been designed to the strict figures of this formula. Most of those ex¬amined will not hold back the water that they are supposed to hold back. E. T. POWELL-If the pillar remains ac¬cording to the Mine Inspectors' formula? W. L. EATON-We have not found very many where the provisions were followed. E. T. POWELL-Where the Mine Inspec¬tors' formula has been fully complied with, have there been failures or not? W. L. EATON-I cannot say. Most of these barrier pillars probably were designed in accordance with this formula, but most of them, if they were so designed, are not in that shape now because a large number of them will not hold back the water; they have been reinforced, and they are punc¬tured in various places. Holes have been driven through them to relieve the hydro¬static pressure to avoid a failure. They do not dare to have a failure. In many instances, the barrier is punc¬tured to avoid a failure. In order to mine their coal safely, many companies must pump water from mines that were aban¬doned many years ago. R. MAIZE-That is true, Mr. Eaton, but do you know of any case where a barrier pillar actually failed and flooded an ad¬joining mine when the pillar had been left in accordance with the Mine Inspectors formula?

Jan 1, 1948

By W. S. Keyes

(Read at the Amenia Meeting, October, 1877.) EASTERN NEVADA. THE State of Nevada, known par excellence as "the Silver State," occupies the major portion of the wide plateau, or so-called Great Basin, lying between the Sierra Nevada range on the west and the Wahsatch range of the Rocky Mountains on the east. It extends from the 114th degree to the 120th degree of longitude, west of Greenwich. It is limited, on the north, by the 42d degree of latitude, and on the extreme south by the 35th degree of latitude. Its general shape is that of an irregular parallelogram, from which the lower or southwestern portion has been cut off by a diagonal southeasterly line; the missing portion forms a part of the State of California on the west. The Great Basin is made up of a succession of low hills, or minor mountain ranges, running very nearly north and south, with long valleys between them. All of these mountains are more or less metalliferous. On the western rim, marking the eastern flank or foothills of the Sierra, we find granites, porphyries, and propylites. Here we note the great Comstock lode, with its free-milling gold and silver ores, and still further south the once prominent and the now reviving gold and silver-bearing districts of Esmeralda County, Nevada, and of Morro County, California. Next, at some distance to the east, we find the mining districts at and near Unionville, in Humboldt County. Still further to the east we find the Battle Mountain copper-silver district, north from the railroad, and southerly therefrom the Austin or Reese River, Belmont, and other districts. Still further east and north of the railroad, we find the Tuscarora, a new district of very

Jan 1, 1878

By G. W. Garside

In order to render my descriptions more intelligible, I have compiled a general map of this section of Alaska, showing accurately the relative positions of the most important districts where valuable deposits of minerals have been discovered (page 819). Upon inspection of this map, it will be observed that the chief metalliferous belt in this mineral field is in close proximity to the mainland shore, the trend of which it follows for more than a hundred miles in a northwest and southeast course, while the mineral croppings on the adjoining islands are much shorter in extent, and more irregular with respect to their strike and continuity. This principal metalliferous zone, which I will call the main-land system of lodes, contains gold, silver and lead, besides traces of copper, zinc and iron, gold being found extensively in a free state and also associated with sulphur, and with many of the sulphides of iron, lead and other substances. On the line of this belt, as shown on the map, there are a number of distinct mineral districts. Beginning at the southerly extremity, they are named as follows: Sumdum, Snettishham, Grindstone Creek, Sheep Creek, Gold Creek, Lemon Creek, Montana Creek and Berners Bay districts, each deriving its name from the hay or creek on which it is situated. Harris mining district, as legally organized under the local customs, rules and regulations adopted by the miners of Juneau, embraces, within its exterior boundaries, Grindstone, Sheep, Gold and Lemon Creeks, and all of Douglas Island. The limits of this immense metalliferous horizon are becoming definitely known through the exposures made by prospectors. The belt, as now recognized, varies in width from one to several miles, the lateral measurement being greatest at Juneau in Harris district, where the famous Treadwell mine, with its slate foot-wall, marks the westerly boundary of the zone, while the eastern side of Silver Bow Basin, with a granite hanging-wall, defines its easterly border.

Jan 1, 1893

By Theodore Simons

Permission to present this paper at the February, 1915, meeting of the Montana Section of the American Institute of Mining Engineers was liberally granted by W. A. Clark, Jr., President-and General Manager of the Timber Butte Milling Co., and by the representative of the Minerals Separation Co. For the many courtesies shown the writer on his visits to the mill and for information supplied, he is indebted to all the officers of these companies, especially to W. N. Rossberg, W. D. Mangam, Hamilton Cooke, Jr., T. M. Owen, T. C. Wilson, R. McGillivary, L. L. Quigley, C. Bartzen and others. The writer takes this opportunity to herewith express to them his appreciation and sincere thanks. Location of Mine and Mill The concentrator of the Timber Butte Milling Co. was built to treat the ore mined at the Elm Orlu mine of the Elm Orlu Mining Co., which carries zinc and lead in sphalerite and galena; copper in bornite, chal-cocite, tennantite, and tetrahedrite; and gold and silver either free or chemically combined with the sulphides of the base metals. The gangue is chiefly quartz, barite, fluorite, rhodonite, and rhodocrosite. The iron in the ore occurs as irqn pyrites. The Elm Orlu mine is situated in Butte, Silver Bow County, Mont., near the northern border of what is locally known as the Butte sulphide-copper belt, about one mile north of the Anaconda mine, and adjoining the Black Rock zinc mine of the Butte & Superior Co. on the southwest. The mill is on the northern slope of Timber Butte, a prominent topographical landmark in the Butte district. This site permits to a large extent the gravity system of ore flow; it presents a convenient and extensive area for a tailings pond; and it is comparatively near to the source of water supply and to existing railroads.

Jan 1, 1916

Joseph E. Thropp, Jr., Indiana Harbor, Ind.:—To what do you attribute the fact that in some localities the by-product coke sells at a premium over the ordinary bee-hive coke for foundry use ? If the cell-structure is preferably soft and rather thick in coke for foundry use, as I understand it, do you mean that by-product coke has soft and thick cell-walls ? William H. Blauvelt, Syracuse, N. Y.:—As I say in one of the paragraphs of my paper, the tendency seems to be towards the manufacture of foundry- and furnace-coke under somewhat different conditions. The development of the best cell-structure in coke, of course, has not reached perfection, but we are making progress, and we are inclined to believe that under ordinary conditions the best furnace-coke, that is, coke with the hard cell-wall and the well-developed cell, is produced at fast coking-time and high heats, whereas the best foundry-coke seems to be produced at somewhat lower heats. In one of our plants we are making furnace-coke in 16-hr. coking-time, and foundry-coke in 20-hr. time. Foundry-men want the strong, tough coke. I think the furnace-men present will agree that the best furnace-practice requires a hard coke, with a well-developed cell-structure. Replying to the question as to the reason for higher prices being realized for by-product foundry-coke than for bee-hive coke, of course, the immediate reason is that it suits the foundry-men better. Perhaps one cause may be that we are able, by the selection of coals, which is not usually practicable at bee-hive plants, to get a quality and analysis best suited to foundry-work, with high carbon-content, and with cell-structure and physical strength especially suited to the foundry-men's ideas.

Jan 1, 1913

Prof. H. S. Munroe, New York City : In his reference to cop per-dressing at Lake Superior, p. 325, Mr. Douglas says that " the .. concentration .. . has been carried out with greatest financial economy,... I do not say with the greatest economy of min eral." And again, on p. 344, referring to the same, " it would not pay to reduce the quantity treated, and increase hand-labor, in order to save a few hundredths of one per cent. of copper." Mr. Douglas probably has in mind the fact that the copper lost is all included copper, locked op in grains of sand. To save this, the rock must be crushed finer. If the mesh of the stamp-screens be reduced, the stamps will crush less; and thus we shall have to reduce the quantity treated in the mill per day, while the labor re mains the same per day, or is increased per ton, as he says. Submitting to the loss of copper, however, is not the only solution of the difficulty. A large quantity of rich sand is now collected by the jigs, and it would be easy to save so much of this material that the escaping sands would be quite poor. What is wanted at Lake Superior, and at many dressing-works in this country, is an efficient crushing-machine to treat the sands thus collected. Abroad, we have the Heberle machine and the Schranz mill for this purpose, the latter being the more successful. The Heberle grinder was tried at the Calumet and Hecla mill for crush ing these rich sands, with what success I do not know. I should like to ask Mr. Douglas if we have no American crushing-machine that will reduce jig-sands to a fine state of division

Jan 1, 1894

By W. S. Keyes

The State of Nevada, known par excellence as " the Silver State," occupies the major portion of the wide plateau, or so-called Great Basin, lying between the Sierra Nevada range on the west and the Wahsatch range of the Rocky Mountains on the east. It extends from the 114th degree to the 120th degree of longitude, west of Greenwich. It is limited, on the north, by the 42d degree of latitude, and on the extreme south by the 35th degree of latitude. Its general shape is that of an irregular parallelogram, from which the lower or southwestern portion has been cut off by a diagonal southeasterly line; the missing portion forms a part of the State of California on the west. The Great Basin is made up of a succession of low hills, or minor mountain ranges, running very nearly north and south, with long valleys between them. All of these mountains are more or less metalliferous. On the westcrn rim, marking the eastern flank or foothills of the Sierra, we find granites, porphyries, and propylites. Here we note the great Comstock lode, with its free-milling gold and silver ores, and still further south the once prominent and the now reviving gold and silver-bearing districts of Esmeralda County, Nevada, and of Morro County, California. Next, at some distance to the east, we find the mining districts at and near Unionville, in Humboldt County. Still further to the east we find the Battle Mountain copper-silver district, north from the railroad, and southerly therefrom the Austin or Reese Ever, Belmont, and other districts. Still further east and north of the railroad, we find the Tuscarora, a new district of very

Jan 1, 1879

By Hans M. Ewoldsen

The generation and evaluation of solutions to body force problems is of extreme interest to the geotechnical profession, as all natural stress states must necessarily include some contribution from the weight of the material. In this chapter the elastic solution for the stress field around a circular, horizontal tunnel at an arbitrary depth beneath the surface of a half-space is reexamined. The influences of body force, initial stress, and free surface proximity are examined and related to in-situ cases. The solution as presented deals only with an isotropically elastic medium; this medium is further considered only in a half-space configuration. It is readily apparent that these restrictions impose severe limitations if analogies are attempted with in-situ cases where geologic discontinuities, inhomogeneities, and irregular boundaries exist. The question might be raised as to the propriety of geotechnically oriented researchers even considering such idealized conditions. There is, however, much to be gained from study of such solutions. The lack of geologic discontinuities and inhomogeneities allows the investigator to separate and leisurely examine such parameters as are included in the solution, without worry of interrelationships of a host of other parameters. Further, elastic solutions have had extensive usage prior to the development of such techniques as the finite-element solution. It is interesting to compare body force solutions with the external field solutions which in the past have been used for design purposes. Finally, the exact solution may be used to verify the accuracy of the finite-element type of solution. The mathematical solution on which this chapter is based was originally developed by R. D. Mindlin.l Because of the complexity and length of the solution, no attempt was made to determine the resultant stress fields until the advent of the present-day high-speed digital computer. How-

Jan 1, 1972

By Henry D. Hibbard

Henry D. HibbaRd, Pittsburgh, Pa,: This is a most interesting and instructive paper, some of whose lessons should find immediate application. It points out how fuel-consumption is to be decreased in open-hearth practice, by changes in the plan of the furnace. To look first at the greatest item of loss, radiation, it is seen that thicker brick-work is advisable to lessen this. Especially is this true of the roof, made at present, almost universally, only 9 inches thick to prevent cutting. Now that high roofs, well above the course of the flame, are becoming general, and the average melter is better able to judge the temperature of his furnace, that reason has less force; and we may build roofs 18 inches thick, or perhaps better cover the usual 9 inches with an equivalent layer of sand, which has the advantage of following the arch as it rises and falls with the different degrees of heat. The side-walls of the hearth, usually 131/2 inches thick, may also he thickened up to 18 inches, and the door-linings to 7 inches; and the heat thereby saved will be valuable, while its absence from the working-platform will be much appreciated by the workmen.

Jan 1, 1892

By R. B. Russell

The expansion coefficients of hexagonal (a) zirconium have been calculated from the lattice expansionparameters of both coefficientsofhexagonallow and high hafnium alloys in the range 0° to 600°C. It is found parametersofboththat the coefficients are straight-line functions of the temperature and that the effect of hafnium is to depress the mean coefficients by about 1 pct at room thattemperature and 9 pct at 600°C. The cubic (ß) form was stabilized so that its coefficient could be determined from 400' to 900°C. COEFFICIENTS of thermal expansion for hexagonal-close-packed (a) zirconium were determined up to 600°C (1112°F), without any interference from the effects of preferred orientation, by measurement of the lattice parameters obtained from a symmetrical back-reflection focusing X-ray camera. This paper combines the results for a 1.2 atomic pct hafnium alloy from an earlier report' with those for hafnium-free zirconium. The problem confronting the investigator is essentially that of getting sharp, high-angle diffraction lines which represent the material at a known constanl. temperature and chemical composition. In order to do this, it was necessary to use the proper X-ray emission wave length (Co K was chosen) and to have a fine-grained metal whose atomic spacings would be free from effects of cold work (the specimen was annealed) and to prevent a changing composition owing to gas absorption during the heating of the metal to temperature (the sample was heated in a vacuum). A summary of the effect of temperature on properties is listed in Table I which gives data for ordinary zirconium, as well as new values for the low hafnium metal. The coefficients of the linear thermal expansion that have been reported are given in Table 11. The discrepancies shown may be explained perhaps by the effect of preferred orientation, and McGeary and Lustman2 have done this successfully for sheet metal. The differences in texture cannot explain all the differences in expansion coefficient shown in Table II. liesults by the author agree most closely with those of Kroll.3 Chemical analysis of the high hafnium metal pre- viously reported1 showed that it was 98.22 atomic pct (97.40 wt pct) pure. The low hafnium metal was dehydrogenated Westinghouse crystal bar, designated SMZ-137A. Its analysis was as given in Table 111 (chemical analyses 5377, 5431, and 5432).

Jan 1, 1955

By E. T. Dumble

THE development in the Gulf Coastal Plain for the year 1923 was entirely devoid of any spectacular feature and was considerably less than that of 1922. No large fields were discovered and the principal advances lay in the extension of the old fields and the finding of a new dome and other possible producing structures, which, however, so far, have given only small wells. While the production of some fields, such as those at Hull and Orange, was materially increased at times by comparatively large wells, the output as a whole shows a marked decrease over that of the preceding year. TABLE 1.-Production by Fields in Gulf Coastal Plain in 1923 FIELD BARRELS FIELD BARRELS Anse La Butte 16,942 Jennings 212,376 Barber's Hill 172,660 Markham 39,290 Batson 391,857 North D ayton 74,983 Big Hill (Jefferson County) 13,853 Orange 5,311,995 Blue Ridge 332,445 Pierce Junction 332,565 Damon Mound 822,355 Richmond (Big Creek) 17,545 Edgerley 176,964 Saratoga 700,661 Goose Creek 6,251,761 Sour Lake 2,091,961 High Island 19,018 Spindletop 309,315 Hull... 7,732,139 Vinton 2,134,430 Humble 2,449,744 West Columbia 6,598,589 36,203,448

Jan 3, 1924

Mr. John J. Porter, Chicago Ill. (communication to the Secretary†):—Mr. Baker's account of his experiences with stock-distribution has been particularly interesting to me, as it

Jan 1, 1905

By J. L. Gissy, G. H. Schippereit, J. B. Schroder

THE existence of mechanical anisotropy in hexagonal metals is well known.' One possible method of measuring the degree of anisotropy in a metal is to make hardness measurements on the different planes of a single crystal. So far as is known, no single-crystal hardness data have been reported in the literature for alpha titanium. To obtain an estimate of the variation in hardness with crystallographic direction in titanium, Knoop hardness measurements were made on single crystals of electrorefined alpha titanium obtained from the Bureau of Mines, Boulder City, Nev. The hardness of arc-melted ingots prepared from this material was 64 Bhn (1000-kg load, 30 sec). Crystals of sufficient size were mounted in epoxy resin with the basal plane exposed. They were then polished and etched to remove excess plastic resin and work-hardened surface material. The crystals were then examined by x-ray diffraction, using the back-reflection Laue technique to insure that the crystals were properly oriented and strain free. After Knoop hardness readings (100 or 200-g load) were taken on the exposed surface, the crystals were remounted to expose a prismatic face and the foregoing procedure was repeated. Hardness values for various orientations are listed in Table I. The data show a difference between the hardness of the basal planes and that of the prismatic planes, as anticipated. More striking is the hardness difference observed between different orientations of the indentor on the prismatic planes as shown in Table I and Fig. 1. All of the indentations shown in Fig. 1 were made with a 100-g load. The long axis of indentation A is parallel to the unique (c) axis of the crystal. The deformation marks visible around indentations A and C of Fig. 1 are probably slip traces of the (10.0) system reported by Rosi, et al. The greater hardness observed when the long axis of the indentor was perpendicular to the unique axis of the crystal (indention B) is probably caused by the opera-

Jan 1, 1959

By R. H. Sweetser

At the Buffalo meeting in October, 1898 (Trans., xxviii., 865), our Secretary, Dr. Raymond, in speaking of the obstacles he had encountered in securing contributions to the Transactions from members in practice, said : " It is the disinclination of many members to communicate incomplete or partial or preliminary results. They are going to write, ' some day,' a thorough and monumental paper; and meanwhile they prefer to communicate nothing.... It is the difficulty to which I have just referred that I have encountered in a wide correspondence with members, undertaken for the purpose of securing contributions of fact and opinion concerning the special subject of this discussion.... Almost none of them seem to recognize the value of preliminary, incomplete and indecisive reports of practice, as laying the foundation for a thorough' inquiry." This remark was made in immediate reference to a discussion concerning blast-furnace tuyeres; but, notwithstanding this appeal from the Secretary, little has been recorded regarding the distribution, the penetration, and the pressure of the blast at the tuyeres and inside the iron blast-furnace. I am therefore encouraged to contribute the following incomplete and crude observations of the blast-pressure inside the hearth. At the suggestion of J. H. Frantz, the general manager of the Columbus Iron & Steel Go., a test was made at the East furnace of the company to determine whether there was any difference in blast-pressure at the different tuyeres. The apparatus used for this test was not sensitive enough to give accurate results. It consisted of a small pressure-gauge mounted on a 3/8-in. gas-pipe. A hollow plug, fitting into the peep-hole of the tuyere-cap, prevented the blast from blowing-out during the test. The test-pipe was held in place by means of the handle on the outer end.

Jan 1, 1910

By Jan D. Miller

Under the name given to this column, I almost feel obliged to write about some aspect of grinding, but I have decided instead to comment on the future of chemical processing. In recent years, I have seen a tremendous interest in extractive metallurgy develop among undergraduate and graduate students at the University of Utah. For example, of the 12 graduating seniors this year, over half seem to prefer extractive metallurgy to physical metallurgy. In particular, they seem to be most interested in hydrometallurgy, or chemical processing, obtaining industrial exposure to the phenomena they study via part-time employment at the Kennecott Research Center and the USBM Metallurgical Center in Salt Lake City. The stimulus has been generated by society itself. Many students are dedicated to the proposition that new technology can circumvent the destruction of our environment, a concept which provides considerable motivation. At the governmental level, the recent concern for the quality of our environment has created action in the area of chemical processing both through imposition of stringent air and water quality standards, and through increased funding for technological research in this area. The National Academy of Sciences (NAS) gave impetus to this movement when it pointed up the need for development and support of such disciplines as extractive metallurgy, particularly chemical processing, in a recent report on Mineral Science and Technology. The recommendations in the NAS report have prompted governmental action on many fronts, including the Bureau of Mines, and have also given rise to direct legislation in the form of two bills -H. R. 3492 and S. 635- presently before Congress to a mineral engineering education. The report recommends that chemical processing technology (more generally extractive metallurgy) be developed by both new engineering techniques and unconventional chemical techniques such as application of the chemistry of nonaqueous liquids to mineral systems.

Jan 1, 1971

By E. T. Dumble

THE development in the Gulf Coastal Plain for the year 1923 was entirely devoid of any spectacular feature and was considerably less than that of 1922. No large fields were discovered and the principal advances lay in the extension of the old fields and the finding of a new dome and other possible producing structures, which, however, so far, have given only small wells. While the production of some fields, such as those at Hull and Orange, was materially increased at times by comparatively large wells, the output as a whole shows a marked decrease over that of the preceding year. TABLE 1.-Production by Fields in Gulf Coastal Plain in 1923 FIELD BARRELS FIELD BARRELS Anse La Butte 16,942 Jennings 212,376 Barber's Bill 172,660 Markham 39,290 Batson 391,857 North D ayton 74,983 Big Hill (Jefferson County) 13,853 Orange 5,311,995 Blue Ridge 332,445 Pierce Junction 332,565 Damon Mound 822,355 Richmond (Big Creek) 17,545 Edgerley 176,964 Saratoga 700,661 Goose Creek 6,251,761 Sour Lake 2,091,961 High Island 19,018 Spindletop 309,315 Hull 7,732,139 Vinton 2,134,430 Humble 2,449,744 West Columbia 6,598,589 36,203,448

Jan 3, 1924

By G. Nabi, W-K. Lu

Cylindrical specimens of natural dense hematite were reduced to magnetite at atmospheric pressure in H2-H2O mixtures of known composition over the temperature range 1084° to 1284°K. The rate of reduction was measured by the rate of movement of the interface between hematite and magnetite. The diffusion of gases through the gaseous boundary layer, the magnetite layer, and the interfacial chemical reaction were all considered in the interpretation of experimental data. The mass transfer coefficient through the boundary layer was calculated using accepted correlations. Values of the chemical reaction rate constant and the diffusivity of hydrogen in the magnetite phase were determined. THE present investigation is concerned with the reduction kinetics of natural hematite to magnetite by H2-H2O mixtures in the temperature range 1084" to 1284°K at atmospheric pressure. This reaction is the first step in the series of topochemical reactions in the process of reducing hematite to iron. Kinetic information of the simple steps such as hematite-magnetite transformation is necessary in order to have a better understanding of the complex processes of hematite reduction in iron-making. It also has direct industrial significance because magnetic roasting is one of the most important methods in benefication of lean ore.&apos; Although many technical papers have been published on the process of magnetic roasting and iron oxide reduction, very little information is available in the literature concerning the fundamental nature of hematite reduction to magnetite by reducing gases. Hansen et al.2 reduced the dense synthetic pellets of high-purity oxide in CO-CO2 mixtures and determined the reaction rate by weight-loss method. They were able to interpret most of their results by applying the interfacial area control theory developed by Mckewan.3 In contrast, Wilhelm and St. Pierre,4 who studied reduction of hematite to magnetite in H2-H2O mixtures by weight-loss method, stressed that the resistance of the porous magnetite layer to the diffusion of gases cannot be neglected in consideration of the overall reaction rate. In the present study the contributions of interfacial chemical reaction, diffusion of gases through the magnetite phase, and the gaseous boundary layer to the overall reaction rate will be considered. APPARATUS AND PROCEDURE Hematite Specimens Preparation. Natural hematite ore from Vermillon range of Northern Minnesota was selected for the present investigation because of its high purity and thermal stability. Chemical analysis of five samples gave the following average values: 67.52 pct total iron (96.62 pct Fe2O3, 0.28 pct FeO, 0.03 pct metallic iron), 2.53 pct SiO2, <0.07 pct MgO, 0.03 pct CaO, 0.05 pct combined mixture, 0.07 pct loss on ignition, and 0.34 pct other. Cylindrical specimens of 0.93 cm in diam and 2.7 cm in length were drilled from slabs of ore with a water-cooled diamond core drill. These specimens were heated to 1000°C and furnace-cooled. Specimens with silica pockets developed large cracks. The uncracked specimens were heated a second time, and their surfaces were carefully examined with a microscope. Those with hairline cracks or surface inhomoaenitv-- were rejected. Preparation of H2-H2O Mixtures. H2-H2O mixtures were prepared by the combustion of H2-O2, mixtures in a pyrex glass chamber in the presence of a catalyst. Alumina pellets coated with palladium, supplied by Englehard Industries, were used as the catalyst. Purified grades of hydrogen and oxygen were used which were repurified by usual techniques. Hydrogen before entering the combustion chamber was passed through an activated alumina H2O absorption bulb, with copper turning at the top. The cover of this bulb was not made pressure-tight so that any pressure development in the hydrogen line would cause the cover to blow off and also the copper turnings would act as a flame arrester in the case of a flashback from the combustion flame. Oxygen flow rates were measured with a bubble flow meter after purification with 1 pct accuracy. Hydrogen flow rates were measured by "precision wet test meter" and the amount of unburnt hydrogen was accurately measured by a bubble flow meter, after condensing water vapor in the gaseous stream. The Pyrex glass bulb contained concentric Vycor glass tubes as shown in Fig. 1. Oxygen was prevented from diffusing into the hydrogen line by threading platinum wire through pores at the combustion end of gas inlet tube. The glass bulb was heated with a Kanthal heating wire pasted in asbestos paper. The surface temperature of the bulb was measured with a thermocouple and adjusted to remain at approximately 350°C. The gaseous reaction chamber also served as a preheater for gases to avoid thermal segregation. The following sequence of operation was adopted. 1) Nitrogen was passed through the outer concentric tube to purge the catalyst bulb of oxygen. 2) Hydrogen was introduced through the inner tube until a steady flow was obtained. 3) Oxygen was then introduced into the nitrogen stream passing through the outer tube. 4) When combustion had commenced and a flame was visible over the platinum wire, the N2 was turned off.

Jan 1, 1969

By P. A. Laxen, H. R. Spedden

WHEN a mineral particle is fractured, bonds between the atoms are broken. The unsatisfied forces that appear at the newly formed surface are considered to be responsible for the adsorption of ions at the mineral surface. A knowledge of the mechanism and extent of ion sorption from solution onto a mineral surface is of interest in the development of the theory of flotation.&apos;*&apos; Study of the adsorption of sodium from an aqueous solution oftheon quartz offers a simple approach to this complicated problem. The availability of a radioisotope as a tracer element meant that accurate data could be obtained."." Three main factors which appeared likely to affect the adsorption of sodium are: l—concentration of sodium in the solution, 2—concentration of onotherof cations in the solution, and 3—anions present in the solution. Hydrogen and hydroxyl ions are always present in an aqueous solution. By controlling the pH, the concentration of these two ions was kept constant. The variation in thesethe amount of sodium adsorbed with variation in sodium concentration was then determined under conditions standardized in regard to hydrogen ion. The effect of concentration of hydrogen ions and of other cations was also measured. A few experiments were made to get a preliminary idea on the effect of anions. The active isotope of sodium was available as sodium nitrate. Standard sodium nitrate solutions were used throughout these experiments except when the effects of other anions were studied. It was found that sodium adsorption increased with sodium-ion concentration, but less rapidly than in proportion to it. Increasing hydrogen-ion concentration, or conversely decreasing hydroxyl-ion, brings about a comparatively slight decrease in sodium-ion adsorption. Increasing the concentration of cations other than hydrogen or sodium decreases somewhat the adsorption of sodium ion. It would appear as if the kind of anion is a secondary factor in guiding the amount of sodium ion that is adsorbed. Materials and Methods Quartz The quartz was prepared as in previous work in the Robert H. Richards Mineral Engineering Laboratory&apos; except for the refinement of using de-ionized distilled water for the final washing of the sized quartz, prior to drying." To minimize the laborious preparation of quartz, experiments were made to determine .whether the sodium-covered quartz could be washed free of sodium and re-used. The experiments were successful as indicated by lack of Na" activity on the repurified material and by its characteristic sodium adsorption. Table I gives the spectrographic analyses of the quartz used. The quartz ranged from 16 to 40 microns in size, averaging about 23 microns (microscope measurement), and had a surface of 1850 sq cm per g (lot I), 2210 (lot 11) and 2000 (lot 111) as determined by the Bloecher method." Radioactive Sodium Method of Beta Counting for Adsorbed Sodium: Na22, the radioisotope of sodium, possesses convenient properties.&apos; It has a half-life of 3 years, thus requiring no allowance for decay during an experiment. On decay it emits a 0.575 mev ß+ radiation and a 1.30 mev r radiation. The decay scheme is illustrated in the following equation: ß+ NaR-------&apos;8&apos;77NeZ2 3 years The /3 radiation is sufficiently strong to penetrate an end-window type of Geiger-Mueller counting tube. This, in turn, makes it possible to use external counting, a great advantage in technique. Furthermore, it permits the assaying of solids arranged in infinite thickness, while assaying evaporated liquors on standardized planchets. The equipment used was standard and similar to that employed by Chang.R The original active material was 1 ml of solution containing 1 millicurie of Na" as nitrate. This active solution was diluted to 1000 ml. Five milliliters of this diluted active solution was found to give a quartz sample a sufficiently high activity for accurate evaluation of the sodium partition in the adsorption measurements. Also, 1 ml of final solution gave a sufficiently high count for precision on the liquor analyses. The sodium concentration of the diluted active solution was 1.2 mg per liter, so that 6 mg of sodium for 60 ml of test solution and 12 g of quartz was the minimum amount used. The active solution was stored in a Saftepak bottle. Procedure for Adsorption Tests: The method consisted of agitating 12 g of quartz with 60 ml of solution of known sodium concentration for enough time to establish equilibrium between the solution and the quartz surface. The quartz was separated as completely as possible from the solution by filtering and centrifuging. The activity on the quartz and in the equilibrium solution was measured and the partition of the sodium was calculated from the resulting data. The detailed procedure for the adsorption test is set forth in a thesis by Laxen." In brief, it included the following steps: 1—Ascertainment of linearity between concentration of Na" and activity measured. 2—Evaluation of factor to translate activity on solid of infinite thickness in terms of activity on an evaporated active film of minute thickness, on the various shelves of the counter shield. 3—Taking precautions to avoid evaporation of water during centrifuging

Jan 1, 1953