Search Documents

Discussion of the paper of R. H: Sweetser,. presented at the Cleveland meeting, October, 1912, and printed in Bulletin No. 71, November, 1912 pp. 1327 to 1334. See also Bulletin 11 No. 72, December, 1912, pp. 1561, 1562. J. J. HOWARD, Dover, N. J. (communication to the Secretary*) :-No doubt there are as many different methods of starting a blast-furnace as there are men who assume that responsibility. Having blown-in a furnace a few years ago in a manner similar to that outlined by Mr. Sweetser, things went along so well at the start that I had time for a little reflection on what was going on inside the furnace. I saw the wood turned to charcoal practically, and it occurred to me, why should I use wood when I could put in the charcoal in the. first place, and thus save a lot of time, and also eliminate the dangerous gas from the wood, which is the cause of most of the accidents in starting up a furnace. I had a furnace out for repairs and decided to use no cord-wood in blowing in. I put in about a carload of charcoal and used no wood except some shavings and oily waste at each of the tuyeres. The furnace had 16 tuyeres and was 100 by 22 by 14.5 ft. Hot rods were put in each tuyere' and the blast started immediately at 11 a.m. Within 5 mill. the air was all driven out of the stack and the gas lighted of its own. accord at the top of the furnace. It was allowed to burn for 5 min. longer and then the bell was closed and the gas taken to the last stove and the last boiler on the gas-main. It was all clone so quietly that it was hard to realize that the gas was down. The tuyeres were as bright as if the furnace had been in blast for a long time. I have learned since that others have used the same method, but they had not passed the good advice along.

Jan 5, 1913

By Frederick Forscher

Frederick Forscher (Nuclear Materials and Equipment Gorp.)—It is gratifying to see another series of experimental results that essentially reconfirms our reported observations of "Strain-Induced Hydrogen Embrittlement in Zirconium" (F. Forscher: AIME Trans., 1956, vol. 206, p. 536, noted as Ref. 3 of paper). However, several important considerations may have been overlooked, or—at least—have not been specifically pointed out. It is the purpose of this discussion to present some of these considerations. The statement is made that "the equilibrium concentration of hydrogen in solution at 20°C in zirconium is approximately 10 ppm; i.e., no zirconium hydride precipitates are formed at or below this hydrogen content." This is perhaps the case in the unstressed condition. In the presence of triaxial (plastic) strain however, even as little as 1.4 ppm H2 (Forscher's Figs. 6 and 11) will cause porosity near fracture in 20°C tests. The necked-down region that develops during a tensile test provides the triaxiality necessary for these pores to open. Both Beevers' and Forscher's micrographs show that porosity is concentrated in the necked region. So-called "pure zirconium" containing about 10 ppm H2 also shows pronounced porosity near fracture (Beevers' Fig. 3). Since it is generally agreed that such porosity is

Jan 1, 1965

By Fred P. Peters

T. D. Yensen.*—As my information is of a negative nature, I think it belongs under this paper. We are particularly interested in magnetic materials and we would like very much on occasions to make use of powder metallurgy. We have tried repeatedly to use powder metallurgy in preparing our nickel alloys but always. with negative results; that is, we cannot get as good magnetic properties by powder metallurgy as we can by starting with a molten material. We have tried by all possible means to make materials' like 50 per cent iron-nickel alloys by powder metallurgy. The compacts can be regularly lorged and rolled but no matter what we do in the way of annealing, the magnetic properties come out very much poorer than if we start with molten material. F. V. Lenel. †—I want to mention one characteristic of articles made from metal powders which distinguishes them from die castings; that is, their wear resistance. Die castings usually are made from zinc or aluminum alloys and a few copper-zinc alloys; all of them are comparatively soft and not very wear resistant. I know of a number of cases where powder metallurgy rather than the die-casting method was used for producing a certain part because higher wear resistance was needed than could be attained in die castings. A, J. LanghammeR.*—The subject of powder metallurgy is somewhat difficult to discuss, and portray, in the time that his been allotted. Most of you would rightly be bored if we went into details. However, I will cite one incident that possibly will help illustrate some of the potentials. Last summer I was in Washington and met Navy officials for the purpose of studying the possibility of making a certain part by powder metallurgy. The part is highly intricate and I happened to remark that the material cost would be high; that is, the cost on one raw material. Promptly a high-ranking Navy officer said: "Mr. Langhammer, if you must pay x dollars a pound for the raw material, but achieve the desired results, the cost of the finished part would still be low."

Jan 1, 1945

By Edward Halse

The occasional occurrence in metalliferous veins of rounded fragments of rock, matrix or ore, lying loose, embedded in clay, or enclosed in some kind of cement, may be attributed to four causes:— I. They have been washed in from the surface, or from an upper portion of the vein.. II. They are of concretionary origin. III. They have been produced by movements in the country-rock or in the walls of the vein. TV. They have been formed in situ, by the upward, downward or lateral flow of water in the vein itself. In this paper the word " conglomerate " is confined to a rock composed of rounded fragments or pebbles cemented together, as distinguished from a " breccia," in which the rock-fragments are angular. * I. Boulders and Pebbles which have been Washed in from the Surface, or from an Upper Portion of the Vein. In this type it is presupposed that the vein at one time communicated by a fissure or open space with the surface, or with the upper portion from whence the fragments have been washed. One well-authenticated occurrence was described long ago by Fournet. Owing, no doubt, to later dislocations in the lode, pebbles from an old alluvium and sands containing titaniferous iron, as well as fragments of wood, were found in a vein at Huelgoet, in France. " Toutes les parties tendres du filon de Pranal ou ces phenome'nes sont les plus prononces ont 6th excaves jusqu'a d'aasez grandes profondeurs par I' impetuosite des torrents, qui out depose la matiere alluviale.'"

Jan 1, 1906

By P. Marier, T. R. lngraham

The kinetics of the sulfation of MnO,, MnzO3, and Mn3O4 in SO,, SO3, and O, mixtures was examined and the descending order of sulfation rates at temperatures near 400°C was found to be Mn,O3 > MnO, > Mn3O4. The respective activation energies for the thermal decomposition of MnO, and Mn,O, are 39 and 47 kcal. At 900°C, the thernzal decomposition of MnSO, to MnzO3 is slower than that to Mn3O4. The respective activation energies are 62 and 51 kcal, respectitely. MANGANESE is used to improve the hot workability of steel in the proportions of approximately 13.5 Ib of ferromanganese per ton of steel produced. This requirement accounts for about 95 pct of its large industrial market in North America. The remaining 5 pct is used in the battery and chemical industries. In most North American ores, the percentage of manganese and the manganese-to-iron ratio are not suitable for the direct production of ferromanganese. Hence, most of the North American requirements for manganese are satisfied by importing ore. Typically, many of the studies done on native low-grade manganese resources have been directed toward the production of ore substittes" and the recovery of manganese from open-hearth slags.3 Of the wide variety of processes which have been proposed, the most popular involve compounds in the Mn-S-O system. The thermodynamic properties of manganese and its compounds were reviewed by ah' in 1960 and, more recently, lngrahams discussed the thermodynamics of some of the reactions involved in the Mn-S-O system at normal roasting temperatures. The conditions for producing manganese sulfide during the reduction roasting of manganese sulfate are discussed by Fuller and Edlund.9 A novel scheme was proposed recently by zimmerley7 for utilizing waste sulfur dioxide from stack gases to recover the manganese from ocean-mined manganese nodules. Very little of the work published on manganese compounds has been related to reaction rates. Singleton et 1.' studied the rates of reaction on the MnO-C and Mn7C3-3MnO systems and observed linear and parabolic kinetics respectively in the systems. Tatievskaya et a1.' studied the low-temperature reduction of Mn&, MnO,, and Mn& in HZ and CO, and reported activation energies in the range 1628 kcal. In this paper, the rates of some of the decomposition and formation reactions involving MnSO4, MnOz, MnzO3, and Mn3O4 will be examined after the conditions for the thermodynamic stability of the individual compounds have been designated. CONDITIONS FOR STABILITY OF MnSO4, MnOz, MnZO3, AND Mn3O4 The areas of stability for h'hSO4, MnOz, MnzO3, and h3O4 were established from the data of Mah4 and Ingrahams and are shown in the predominance area diagram,10 logpq- logpsq, in Fig. 1. The diagram is drawn for two temperatures, 700°K, solid lines, and 1100°K, dotted lines. The sketch for the lower temperature includes the conditions likely to prevail in the Zimmerley patent7 when manganese nodules react with sulfur dioxide and that for the higher temperature indicates the conditions for recovering MnzO3 or Mn3O4 from MnSO4 during a roasting reaction. From the fact that the boundary between the areas of stability of MnOz and hSO4 at 700°K is parallel to the abscissa, it is evident that MnOz and SO2 should react together to produce MnSO4, irrespective of the oxygen pressure in the system. If the source of sulfur for sulfation were from waste flue gases, it is likely that the oxygen content of the gas stream would be more than sufficient to oxidize any MnsO4 to MnzO3, 107 atm of O2 required, or even to convert any Mnz03 to MnOz, 0.02 atm OZ required, prior to sulfation. At 1100°K, the diagram indicates that MnSO4 may be converted directly to either MnzO3 of Mn3O4, depending upon the prevailing partial pressure of oxygen. When the gas stream contains more than 1 pct Oz, logpq = -2, only MnzO3 would be recovered from an experiment done under equilibrium conditions. At oxygen partial pressures of less than 1 pct, one would expect to bring about a reversible exchange between MnSO4 and Mn3O4 by appropriate adjustment of the partial pressure of SOZ. These various reactions will be described in the subsequent kinetic experiments.

Jan 1, 1969

By Francis Laur

BAUXITE, at first considered as a mineralogical curiosity without importance, now attracts daily increased attention from mineralogists, geologists, and manufacturers. The metallurgy of aluminum, which has entered with the advent of electrolysis upon a new phase within the last few years, requires every day larger quantities of pure alumina, and this can only be obtained from bauxite, which is, of known substances, the richest in free alumina. Bauxite has been mined since 1872 in France, whereabout 200,000 tons have been produced, and where, as a natural consequence, its deposits, qualities, and applications have become known. Within a few years past, discoveries of important deposits of bauxite have been made in the United States and Canada, and this almost entirely new subject has thus acquired an additional interest for the mining engineers and metallurgists of the American continent. A brief summary of the available data concerning it appears likely, therefore, to be appropriate and valuable.* I.—HISTORICAL. It was in 1821 that the famous chemist Berthier discovered at Baux (Bouches du Rhône) a hydrate of alumina (varying from 66 to 79 per cent. in its contents of the oxide) mixed with silica and

Jan 1, 1895

By J. G. Thompson

Determinations of the hydrogen content of irons and steels invariably are subject to two serious difficulties: (I) the determination of amounts of 0.001 per cent or less of any constituent requires an analytical procedure of unusual precision and accuracy, and (2) the hydrogen content of many samples is dccidedly not stable; i.e., there is no assurance that the content at the time the analysis is made is the same as it was when the sample was taken or at some previous time in the history of the piece. In respect to both the precision and speed of the determination, the vacuum-extraction procedure for the determination of hydrogen possesses advantages over the vacuum-fusion procedure, which has been the recognized standard for the detcrmination of other gaseous elements in sted-— oxygen and nitrogen for example. The basic facts upon which the vacuum-extraction procedure is based—i.e., the evolution of gas from solid steel when it is heated in vacuum, and the fact that the evolved gas is rich in hydrogen—were observed by Graham1 many years ago. Subsequent investigations have shown that hydrogen exists in steel chiefly as interstitial solid solution (i.e., in atomic dispersion) and perhaps to some extent as hydridcs that are unstable and decompose to form atomic hydrogen. In either case practically all of the hydrogen in steel at elevated temperatures exists in the atomic condition and consequently is able to diffuse readily through the metal. In contrast to this, other gaseous elements, such as oxygen and nitrogen, normally are present in steel chiefly in the form of relatively stable compounds such as oxides or silicates and nitrates; i.e., the oxygen and nitrogen atoms are fixed in stable combinations and are not free to migrate. The only oxygen or nitrogen that can diffuse in steel is the small amount in solution (atomically dispersed) and the rate of diffusion of these atoms is much less than that of hydrogen because of their greater atomic volume and lower mobility. Consequently, it is possible to extract most or all of the hydrogen from solid steel in a reasonable time at moderately elevated temperatures, but the procedure is not applicable to the determination of oxygen or nitrogen. It is only within the last decade that these observations have been developed into an analytical procedure for the determination of hydrogen. Apparatus and Procedure The apparatus used at the National Bureau of Standards,6 for the determination of hydrogen by the vacuum-extraction procedure, is shown schematically in Fig. I. The specimen, freshly cleaned and dried,* is suspended on a fine wire within the quartz furnace tube that is connected to the reservoir system and analytical train.

Jan 1, 1945

By A. Simkovich, R. W. Lindsay

The possibility of using sodium sulfide slags to remove copper from ferrous alloys has been investigated by Jordan1 and by Langenberg.2, 3 In these studies, such slags were determined to be capable of removing copper and sulfur from the melt. The present work represents additional effort to clarify the effects of temperature on copper removal. The experiments were performed in a 17-lb induction furnace. Graphite crucibles contained the melts and kept the baths saturated with carbon. Temperatures were measured with a calibrated optical pyrometer and were controlled by manipulation of power input to the furnace. Estimated accuracy of temperatures in this investigation is ± 10°C (18°F) for measurements prior to slag additions, and + 20°C (36°F) after slag formation. The procedure consisted of melting 800 g of electrolytic iron. During this step, powdered graphite covered the exposed iron surface. After a predetermined temperature was reached, copper shot was added. A sample of the molten alloy for chemical analysis was then aspirated into a silica sheath. Next, a slag-forming mixture of sodium sulfite and graphite was added instantaneously to the melt. The sodium sulfite amounted to one-tenth the charge weight of iron; sufficient graphite was added to combine with oxygen in the sodium sulfite, assuming formation of carbon monoxide and reduction of the sulfite to sulfide. Subsequent to the slag addition, the molten alloy was sampled periodically, with the exception of heat A in which no intervening samples were taken between the slag addition and the end of the run. The iron was poured into a graphite mold, and the ingots sectioned and drilled for samples. Results of selected heats are presented in Table I. Analyses of samples drawn from the iron prior to slag addition are listed under zero time. Two samples from heat D were reported with copper contents greater than the initial concentration in the bath. Owing to the gradual but complete disappearance of slag during this heat, it is believed copper momentarily became more concentrated in the upper portion of the bath while reverting from the slag. This is the region from which samples were drawn. It should be noted that analysis of the ingot was equal to the copper content at the time of slag addition. The terminal temperatures of heats D and E, and the initial sulfur content of heat A are also to be noted. Because of the large temperature drop which occurred when slag was formed in heat D, power input to the furnace was increased in heat E after the slag addition, causing a higher terminal temperature. In heat A, the initial sulfur concentration was relatively high as compared to heats B through E owing to contamination by some slag remaining in the crucible from a previous heat. It is evident from Table I that copper was removed at the onset of slag formation. Roughly 30 pct of the copper was taken into the slag, with the exception of heat D, which had approximately 50 pct removed. For a comparatively short time of slag-metal contact, it appears that no gain is to be made in copper removal through use of high or low temperatures. If the slag initially formed remains in contact with the iron for an extended period, temperature has a marked effect upon copper removal, as can be seen by studying results for the two extremes in temperature. At about 1425°C, the copper level remained relatively constant after the initial removal by the slag. However, in the region of 1670°C, a definite reversion of copper occurred. Reversion was incomplete in heat D, and complete in heat E. The final temperatures of heats D and E differed by about 75°C. This temperature difference is thought to be the reason for only partial copper reversion in heat D. It is believed the effects of temperature noted above are related to the evolution of a white fume, which appeared in every run except heat A. (In the case of heat A, the fume was practically indiscernible.) After each slag addition, a yellow flame formed for about 5 sec. When the flame subsided, a white fume appeared. Upon contact with surrounding cooler surfaces, this fume deposited as a white solid. In the experiments made at 1425°C, evolution of fume continued unchanged to the end of the runs. However, heats D and E exhibited a different behavior. A very noticeable decrease in fume evolution from heat D was observed. Furthermore, this heat had much less slag remaining than did runs A through C when the experiments were terminated. No slag remained at the end of heat E; evolution of fume from this heat ceased prior to pouring. Spec-trographic analysis of the white deposit indicated sodium to be the major metallic element, with the maximum concentration of iron and copper as 0.1 and 0.01 pct, respectively. It is supposed the white fume observed in these experiments is principally sodium oxide (Na2O), formed by oxidation of sodium in the slag and subsequent sublimation. (Sodium oxide is a white to gray substance in the solid state; at 1275oC, it sublimes.4) According to this mechanism, elevated temperatures would accelerate removal of sodium from the slag, sulfur pickup by the

Jan 1, 1961

By L. S. Darken

A quadratic formalism is developed lor the representation of the excess free energy, and of the activity coefficients of each component of a ternary system in the vicinity of a single component selected as solvent. This formalism, in contrast to the e formalism, is thermodynamically consistent at .finite concentrations. Numerous specific systems are used as illustrations, with cross checks where possible; these systems are Fe-C-X systems in the vicinity of 1600°C and include practically all those for which reliable data are available. It is shown that this formalism is usually quite adequate to rebresent available data up to a solute concentration of 20 to 30 at. pet. It is hoped that the formalism here presented may prove useful for the treatment and tabulation of data on ternary and multi-component solutions. SINCE, as discussed in a prior paper,' we do not as yet have an adequate basic understanding of the nature of binary metallic solutions, we cannot hope to be in better position for ternary and multicomponent systems. However, the accumulation of thermodynamic data on ternary and multicomponent metallic solutions has led to an urgent need for a rational formalism for the presentation and use of such data. Notable attempts to represent the isothermal isobaric thermodynamics of ternary solutions were made by Benedict et 01.' and by Wohl.3 These attempts were directed toward developing an analytic expression adequate to encompass the entire ternary triangle, primarily for organic systems; they generally involve the power-series approach, which has been shown' to be inappropriate, in general, even for binary metallic systems. On the other hand, interest in the thermodynamics of ternary and multicomponent metallic solutions has tended to focus either on general thermodynamic relations4-10 over wide compositional ranges, or on cases where one or more components have been at rather low concentration. This latter approach has been followed by Wagner,= by chipman,11 and by Alcock and Richardson,12 and more recently in many publications by the same and other authors. It has already been shown' that the thermodynamic behavior of binary metallic systems is, in general, relatively simple only in the terminal regions. Hence, it would appear that any approach, at this time, to a simple formalism for ternary and multicomponent systems must, a fortiori, be limited to the vicinity of the major component or solvent. The present treatment is aimed to be useful for a given solvent with moderate solute concentrations ranging up to 20 or 25 at. pet and in exceptional cases to considerably higher concentrations. In order to achieve even this modest objective, it is necessary that any appropriate formalism have built into it 1) a thermodynamic consistency (at least within the desired degree of approximation), and 2) an approach at infinite dilution to Raoult's law for the solvent and to Henry's law for each solute. Let us first formulate the condition of thermodynamic consistency for a ternary system. Under isothermal isobaric conditions, we may write for the molal value G of any extensive function dG - C1 dN1 + G2 dN2 + G3 dN3 [l] where the G's are the corresponding partial molal quantities and the N's are the atom fractions. Taking component 1 as the solvent, this relation may be rewritten in terms of the independent variables N2 and N3

Jan 1, 1968

By J. D. Meakin

The self-diffusion coefficients of ß tin have been deterttlltled using a plating and sectioning technique. The principal diffusivities pavallel and perpendicu1ar to the "c" axis are given by the Arrhenius relations Dc = 8.2 exp (-25,600/RT) sq cnl per sec and Da = 1.4 exp (-23,300/RT) sq cm) per sec. The results are discussed in terms of a vacancy mecharism of diffusion. In conjunction with an investigation of diffusion in dilute indium-tin alloys we have reexamined self-diffusion in tin single crystals. The published self-diffusion coefficients of tin, eensham') have always appeared anomalous in comparison to diffusion data for other metals and do not correlate with parameters derived from creep tests.' In addition to the necessity of confirming the self-diffusion values for use in analyzing the alloy work, self-diffusion in an anisotropic lattice is of considerable fundamental interest and confirmation of the published data seemed worthwhile. For a crystal with an axis of symmetry three-fold or higher the diffusivity at an angle 6 to the axis is given by D? = (Da - Do) sin2?+ Do [1] where Da and Do are the principal diffusivities perpendicular and parallel to the axis. For a particular diffusion mechanism, again in a crystal of axial symmetry, these principal diffusivities are [2] Do - ? ?i2 COS?i In these expressions ?i is the displacement undergone by the ith atom and 8, is the angle this displacement makes with the symmetry axis. In this, as

Jan 1, 1961

By R. H. Wightman, G. H. Adams

H. C. WEED*—Referring to the use of "dummy fuse" for checking the shots in chute blasting operations, I believe that an even better practice is to blast the chutes with no delay electric blasting caps. Permanent wires can be strung through the grizzly lines and the lead wires from the shots attached to these lines. Using this method, no time is lost in spitting the individual fuses. The possibility of a fused charge becoming dislodged by previous shots and falling into the chute below is eliminated and there is no chance of a man walking back into his own blast. A small hand twist blasting machine or a radio "B" battery can be used to fire the shots if the lines are fired individually. If so desired the entire area can be blasted at once by a switch at the manway or in the drift below. providing a sufficient source of electricity is available. In case a switch is used, proper precaution for locking the switch must be provided. R. H. WIGHTMAN (author's reply) —We do use electric blasting when the number of shots is large; but we have found it more satisfactory to use fuse and caps for individual shots on the grizzly.

Jan 1, 1950

By T. S. Fuller

The work of D. J. McAdam, Jr.1,2 at the U. S. Naval Engineering Experiment Station, Annapolis, Md., on what has been called by him "corrosion-fatigue" has focussed the attention of the engineering profession in general, and of those interested especially in the study of corrosion in particular, on the importance of making tests which will indicate as nearly as possible what can be expected from a given material in service. Pitting is unquestionably the chief agent operating so tremendously to reduce fatigue limits, but in the light of previous work3, 4, 5, 6, 7, 8 it is fair to assume that absorbed hydrogen resulting from the action of the corroding medium upon steel may, under certain conditions, have a perceptible influence. The experiments described in this paper deal more precisely with stressless corrosion, or "prior-corrosion fatigue,"9 and have been carried out to test such an assumption, to segregate, if possible, the effect of pitting from that of absorbed hydrogen, and although very preliminary in nature they indicate results which are striking.

Jan 1, 1929

By T. S. Fuller

The work of D. J. McAdam, Jr.1,2 at the U. S. Naval Engineering Experiment Station, Annapolis, Md., on what has been called by him "corrosion-fatigue" has focussed the attention of the engineering profession in general, and of those interested especially in the study of corrosion in particular, on the importance of making tests which will indicate as nearly as possible what can be expected from a given material in service. Pitting is unquestionably the chief agent operating so tremendously to reduce fatigue limits, but in the light of previous work3, 4, 5, 6, 7, 8 it is fair to assume that absorbed hydrogen resulting from the action of the corroding medium upon steel may, under certain conditions, have a perceptible influence. The experiments described in this paper deal more precisely with stressless corrosion, or "prior-corrosion fatigue,"9 and have been carried out to test such an assumption, to segregate, if possible, the effect of pitting from that of absorbed hydrogen, and although very preliminary in nature they indicate results which are striking.

Jan 1, 1929

By H. Herman, M. E. Fine

Kinetics of reversion and reformation of GP I were studied resistometrically in Al-1.7 at. pct Cu. The reversion process is over in roughly 1/2 minute at 205 "C irrespective of the amount of primary aging. After reversion the occurrence of an incubation time before reaging begins has been substantiated. The reaging kinetics is drastically accelerated by plastic deformation to the specimen. An incubation time is observed only if the specimen is aged before reversion. The incubation time and the effect of plastic deformation indicate that nucleation of GP I is heterogeneous. Simple clusters of copper atoms apparently do not act as nuclei for GP I. AFTER quenching aluminum-rich copper from the solid solution range, Guinier-Preston zones of the first kind, GP I, form very rapidly at room temperature. The rate, largely controlled by the concentration of vacancies, is initially most rapid1 (that is, at the time of the first measurement: 1/2 min) and decreases with time. The nucleation is thought to be athermal. If after aging for several days the GP I is dissolved by reversion at 205°C, according to measurement of Young's modulus an incubation period is observed before GP I begins to form on subsequent aging.2 Yet if the reversion is carried out immediately after quenching, both resistivity3 and modulus changes2 show no incubation effect. The zones which form after reversion have the same structure as those which form after the quench.4 Because of entropy considerations and also the short diffusion time, the solid solution after reversion, 2 min at 205°C, is probably more highly clustered than at the original solution treating temperature, 520" to 550°C. It appears most reasonable to associate with nucleation the incubation time observed on reaging after reversion. A simple cluster of copper atoms, many of which are presumed to be present after reversion, is then not a sufficient nucleus for GP I; a GP I nucleus must contain something in addition to a cluster of copper atoms. The purpose of the present note is to give some additional experimental information concerning the incubation time and rates of reaging after reversion. The existence of the incubation time has been verified by measurement of another property, the electrical resistivity. Acceleration of reaging after reversion by plastic deformation has also been investigated. In acl.dition, the kinetics of the reversion process itself was studied. EXPERIMENTAL Electrical resistance was measured by the poten-tiometric four probe method. The 1.7 at. pct Cu alloy was furnished by the Aluminum Co. of America in the form of 1/2 in. rod. The major impurities reported by Alcoa were Fe (0.002 wt pct), Si (0.003 wt pct), and Mg (0.001 wt pct). Specimens for measuremenl of resistance were prepared by rolling to 0.010 in., cutting 2 by 0.2 in. pieces, rolling the middle pclrtions of these to 0.005 in., and splitting the 0.010 in. sections up to the reduced central section to form current and potential leads. Aluminum extension wires insulated with ceramic tubes were spot welded to the leads. The specimen was supported by the lead wires. The whole specimen assembly was annealed at 500" C in an air furnace for more than 12 hr and then aged at room temperature. This was done to assure quick and complete resolution during subsequent solution treatments. These were carried out in Houghton's "430 Temper Salt" at 520'C for 1 hr. Unless otherwise specified, quenching was accomplished by quickly transferring the specimen from a salt pot to 25°C water. Aging was carried out in a 3 liter dewar of distilled water, rotated and stirred. The temperature was controlled to +0.01°C with a thermomercurial regulator in conjunction with a transistorized relay

Jan 1, 1962

By T. S. Fuller

THE work of D. J. McAdam1,2 at the U. S. Naval Engineering Experiment Station, Annapolis, Md., on what has been called by him "corrosion fatigue" has focussed the attention of the engineering profession in general, and of those interested especially in the study of corrosion in particular, on the importance of making tests which will indicate as nearly as possible what can be expected from a given material in service. Pitting is unquestionably the chief agent operating so tremendously to reduce fatigue limits, but in the light of previous work3, 4, 5, 6, 7, 8 it is fair to assume that absorbed hydrogen resulting from the action of the corroding medium upon steel may, under certain conditions, have a perceptible influence. The experiments described in this paper deal more precisely with stressless corrosion, or "prior-corrosion fatigue, "9 and have been carried out to test such an assumption, to segregate, if possible, the effect of pitting from that of absorbed hydrogen, and although very preliminary in nature they indicate results which are striking.

Jan 1, 1929

By P. R. Smith, R. A. Walters

Borates have been mined in the desert areas of California and Nevada for more than 100 years. To about 1890, playa surface mining provided the chief sources of boron minerals. Underground mining of colemanite and later of borax and kernite was predominate until about twenty years ago. Open pit mining of the large deposits of borax and kernite near Boron, California has been most significant for the past twenty years. Mining of colemanite in the Ryan, California area, near Death Valley, began in 1907. Following the discovery of the large deposits in the Boron area (about 1957), mining in the Death Valley area became nearly nonexistent. Only small tonnages were mined for special uses. Little mining was done in the Boraxo area near Ryan. The first claim was made in about 1915. In 1960 the area became the property of the Kern County Land Company, which was acquired by Tenneco Oil Company in 1967. In 1976 the various boiate properties and claims in this region were acquired by American Borate Corporation. The open pit mine is now approximately 122 m (400 ft) deep, 910 m (3000 ft) long and 305 m (1000 ft wide). The borates in the Boraxo pit consist primarily of three minerals. These are about 50% colemanite (CB6011 5H20), about 40% probertite (NaCaB50g 5H20), and 10% ulexite (NaCaBgOg 5H20). The colemanite, along with boric acid and high-grade colemanite ore from Turkey provide the only sodium-free borates for production of textile grade fiberglas. When heated to its decomposition temperature, colemanite decrepitates to a fine powder, which is the basis for the concentration process. The gangue minerals in this deposit are primarily calcite and clays, including bentonite. The ore body has a very low arsenic content, which is a desirable feature. Test work had been done with samples prior to the results discussed herein. This paper will discuss results of test work which were the basis for erection of a plant, and the subsequent plant operations. Laboratory Calcination and Air Tabling Tests Laboratory calcination tests showed that substantial upgrading of the borate could be accomplished by calcining followed by screening of the calcined material. Removal of the + 28 mesh calcine resulted in borate losses of less than 10% with a rejection of 40 weight % or more of the calcine. The minus 65 mesh calcine generally met the requirement of containing 48%, or more, B203. The minus 28 plus 65 mesh material contained an intermediate quantity of borate and would require additional treatment. Testing demonstrated that ore would not have to be reduced to a size finer than 19 mm (3/4 in.) prior to calcination. A temperature range from 400 to 455OC (750 to 850°F) was apparently satisfactory. Calcination at a temperature of 48Z°C (900°F), or higher, was unsatisfactory due to fusion. All laboratory calcination tests were static tests conducted by placing small covered charges in a laboratory furnace for 40 min. In all tests vapor issues from the furnace for 5 to 7 min. Following this period the ore could be heard "popping," due to decrepitation of the colemanite. The reaction generally continued for approximately one-half hour. Various size fractions of the calcination products from laboratory tests were subjected to laboratory air tabling tests, usually after removing the plus 28 mesh material. Laboratory air tabling tests were conducted employing a Whippet V-80 model air table manufactured by Sutton, Steele and Steele Co. now known as Tripple S Dynamics. Variables include both end and side-tilt, speed of vibration, and quantity of air rising through the deck. In addition to the variables in the machine itself, the feed rate is also a rather critical variable. Testing demonstrated that all - 28 mesh size fractions of the calcine could be successfully concentrated to 48% F2O3 or greater. For the finer material recoveries into the concentrate were between 85 and 90% of the borate. With the coarser material a substantial amount of middling was produced which required cleaner tabling. Laboratory calcination and air tabling tests indicated a process whereby the borate could be concentrated to about 50% B203 with borate recoveries approaching 90%. Moreover, the iron content of the concentrate was well below the required specification of 0.3% Fe2O3. Pilot Plant Calcination Following the laboratory test work described above, pilot plant testing was conducted to prove the process, provide data for engineering studies, and provide product for a prospective purchaser. The kiln used was 0.9 m-diam (3 ft) by 9.0 m (30 ft) long and had a belly section 1.2 m-diam (4 ft) by 2.74 m (9 ft) long near the discharge end. The kiln was operated at a speed of 0.7 rpm. Gas was fired into the kiln at an average rate of 27.1 m3/hr (958.4 cu ft per hr). The air to gas ratio used was 10:1. The ore was fed to the kiln countercurrent to the flame and discharged through a hopper into a screw conveyor which discharged to a 1.2 m (48 in.) Sweco separator. The separator had 28, 65, and 150 mesh screen cloths, with the plus 28 mesh fraction being discarded. The minus 28 mesh fractions were later subjected to air tabling. The exit gases, containing some calcine dust, were swept through two cyclones to recover the dust. The gases then were scrubbed in a Ducon scrubber; very little dust reported past the first cyclone. The dust from the first cyclone was also saved in drums. In addition to the gas rate, the flue gas velocity, after

Jan 1, 1981

NEW MEMBERS The following list comprises the names of those persons who became members during the period of Apr. 10, 1918, to May 10, 1918. BALLARD, JOHN I Supt., Cable Mining Corpn., Cable, Mont. BURKMAN, JOHN M. F., Constr. Engr., U. S. Smelt. Refin. & Min. Co., Care -University Club, Mexico City, D. F. CALLEN, ALFRED COPELAND, Head, Mining Engineering Dept., West Virginia University Morgantown, W. Va. CHADWICK, LAWRENCE, Chem., Mt. Elliott Copper Co., Ltd., Selwyn, via Townsville, North Queensland, Australia. CODY, FRANK W., Skimmer, Reverberatory Furnace, Arizona Copper Co., Clifton, Ariz. COOLBAUGH, MELVILLE F., Prof. of Chem., Colorado School of Mines, Golden, Colo. DODGE, ALLAN WAYNE The Dodge Agency, 104 East Iron Ave., Salina, bans. DONNELLY, LEONARD G., Pet. Geol., Sinclair Oil & Gas Co., Sinclair Bldg., Tulsa, Okla.

Jan 6, 1918

By G. G. Reed

G.G. Reed, Jr. The authors are to be commended for finding a material for pellets binding that we were unable to uncover during the investigations that led to US Patent No. 3,748,116, "Method for producing metallic iron powder from iron ore concentrate," July 24, 1973, by G.G. Reed, Jr., J.M. Karpinski, and S.V. Fox. This patent concerns a method of processing "super"-concentrates prepared from magnetite or "blue dust" into molding-grade metallic iron powder for use as a bulk commodity, in contrast to current methods which produce small batches that are custom-blended with additives and/or alloys to customer specifications. The one thing we had not found at that time was an organic binder (mineral-matter-free) that would allow induration to produce hardened pellets that would survive SL/RN Direct Reduction. Peridur appears to provide this missing link needed for large scale (200 t/a, or 220,460 stpy) single line plant capacity consistent with a low market price to ensure greatly broadened use of metallic iron powder. I hope that industry will adopt this combination so that metallic iron powder usage can fulfill its potential. ?

Jan 1, 1986

G. K. BURGESS,* Washington, D. C.-In the service tests, the Advisory Committee on Aeronautics considered it highly necessary, particularly for seaplanes, to find out whether or not it was necessary to paint exposed parts; reports have been obtained but have not been pub-lished at the present time. Investigations were carried on at three Navy Yards. On just a hurried examination, the inspection was made about two weeks ago and the results are now being digested an examination shows that the aluminum alloys, whether painted or unpainted, stand up very well. It apparently is not necessary to paint, which, of course, is a very important item in the question of the weight of seaplanes. We will be able to report on that, I expect, probably at the next meeting.

Jan 12, 1919

By AIME AIME

TRAINED as a mining engineer and with no little experience in the field of mining, his interests and activities later transferred to the alloying, fabrication, and physical metallurgy of nonferrous metals, principally silver, Robert H. Leach represents in his professional life both of the major phases of the fraternity of mining and metallurgical engineers. In his personal characteristics, his wide circle of true friendships, his kindly, sympathetic interest in the problems of his fellow engineers, be they the junior men of the mineral industries or the mature and experienced men, he typifies the characteristics and attitude so desirable in the professional man.

Jan 1, 1939