Search Documents

By Edwin R. Phelps, Charles W. Porterfield

BACKGROUND OF SURFACE MINING Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal mere mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-pear periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to increase. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu pd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu pd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining. 4) Surface mining normally recovers a much higher percentage of the coal reserve than can recovered by underground mining. 5) Some coal measures call best be extracted by surface mining

Jan 1, 1981

By J. W. Lacey, F. H. Brinkman, J. E. Faris

This paper presents an analysis of the high-pressure, gas-driven LPG-slug process, based on fluid flow tests in areal models. Two types of tests were made. One series was made in low-pressure models which permitted observation of fluid movement. Three completely misci-ble analog fluids were used. A second series of tests was made in high-pressure models using methane, propane and a light refined oil saturated with methane at room temperature and 1,550 psig. Under the test conditions of room temperature and a pressure level of 1,550 psig, the phase diagram for the fluids used is similar to those for many of the field systems where the process is considered for use. A method for using these laboratory data to calculate field performance of the process is outlined. As a result of this work, it is concluded that small banks of LPG (5 per cent HV or less) are not effective in increasing oil recovery in horizontal reservoirs. Znstead, where small banks are used, the driving gas quickly penetrates the LPG bank because of fingering and channeling; and from this point on, the process behaves essentially as an immiscible gas-injection project. The validity of this conclusion was substantiated by: (1) laboratory studies of the effect of rate, model size and mobility ratio on miscible displacement in areal models; and (2) calculation of field recovery, which compared closely with actual field recovery. INTRODUCTION Field applications and pilot tests of the gas-driven, LPG-bank, oil-recovery process are on the increase. Most of these tests are employing small banks (2% to 5 per cent hydrocarbon volume) of LPG, which is miscible with both the driving gas and the oil in place, in an effort to attain an effective yet economical miscible displacement of oil by gas. The expectation of miscible displacement with small banks is based on the concepts that: (1) lengths of solvent-oil mixed zones, measured during miscible displacements in long slim cores, are representative of those that will occur in the field; and (2) areal sweep efficiencies5 measured in electrolytic model studies are applicable to miscible displacement in reservoirs. Our experimental evidence indicates that the mixed-zone lengths and sweep efficiencies mentioned are not applicable to miscible displacement in reservoirs. In this paper we present an evaluation of the gas-driven, LPG-bank oil-recovery process based on fluid flow experiments in areal models. These results are used to predict the performance of a field pilot test of this process, and the results are compared with the actual test results. THE EFFECTIVENESS OF LPG BANKS The effectiveness of LPG banks of various sizes in accomplishing miscible displacement of oil by gas was determined by displacement tests in a model representing one-quarter of a confined five-spot pattern. The model, 12 X 12 X 1/4 in. in size, was packed uniformly with glass beads. It was operated at a pressure of 1,550 psig and at room temperature; the fluids used were methane, propane and refined oil saturated with methane at 1,550 psig. The saturated oil had a viscosity of 1.2 cp at room temperature. The results of these tests are shown in Fig. 1, where recovery is plotted as a function of the volume of fluid injected for: (1) an immiscible-gas drive with an oil-to-gas viscosity ratio of 85; (2) three sizes of LPG banks; and (3) two completely miscible displacements with mobility ratios of 85:1 and 10:1. (The miscible displacement data plotted are the averages of several tests.) The results show that a 2½ per cent bank of LPG does not increase oil recovery over that obtained by immiscible-gas drive. The 7 and 17 per cent banks are, respectively, about 30 and 50 per cent effective (with reference to the M = 85 miscible-displacement curve) in increasing oil recovery at the point where 2½ hydrocarbon volumes (HV) of fluid have been injected. The percentage effectiveness of the banks at a given volume of fluid injected is defined as Recovery by Bank — Recovery by Gas Drive Recovery by Miscible Recovery by Flooding Gas Drive We conclude from these results that banks of LPG smaller than about 5 per cent HV in an individual stratum will cause from little to no increase in oil recovery. This finding was substantiated by work in low-pressure models, which permitted visual observation of fluid movements. In these tests, three completely miscible fluids having the same viscosity ratios as those used in

By F. O. Shuck, F. E. Butler

A diaphragm diffusion cell suitable for use with liquid metals was designed and tested by measuring the diffusion coefficients for a Hg-10 pct In alloy at 25°C. The binary diffusion coefficient and the coefficients for In and Hg tracers were measured at this composition. The measured coefficients for both tracers were less than the binary diffusion coefficient. When these coefficients were combined with the activity correction term of Darken, the predicted binary coefficient was somewhat higher than the experimental value. In recent years a number of investigators have been studying diffusion of liquid metals in order to gain a better understanding of the liquid state and to examine possible applications to liquid metal processing. The bulk of this work has involved either self-diffusion or diffusion of low concentrations of solute metals in an essentially pure solvent metal. The most common experimental technique employed has been the capillary-reservoir method of Anderson and saddington1 since it is well-suited to measurements involving low concentrations of solutes. As an expansion of previous studies, an investigation of the variation of diffusion coefficient over large composition ranges has been undertaken in this laboratory. Although it is possible to modify the capillary-reservoir method for such measurements, the technique loses its principal advantage of requiring only small quantities of solutes. Therefore, it was felt desirable to investigate other possible experimental techniques applicable to measurements over large composition ranges. A technique which has been used widely in measurements of other liquid systems and seemed potentially applicable to studies of liquid metals was the diaphragm cell. This method has been found to combine relative simplicity of operation with accurate and reproducible results. In use with normal liquids, the tyiical diaphragm cell utilizes a porous glass disk. However, because of the high surface tension, it is not possible to use a diaphragm of such fine pore structure with liquid metals. Furthermore. projected use at high temperatures makes the use of glass undesirable. Consequently, the first problem was the search for an appropriate cell design. EXPERLMENTAL Diaphragm Cell. A number of possible cell designs were examined. Prototypes of several were constructed and tested. The final design is shown in an exploded view in Fig. 1. The cell consists of two identical chambers, one on either side of a 0.20-in.-thick partition. The chambers are 0.15 in. deep and have a volume of 3.45 cu cm. Each chamber is provided with two small threaded holes for filling and emptying. The filling holes may be sealed with stainless-steel screws. Drilled lengthwise through the center partition is a 0.250-in.-diam hole. Inserted into this hole is a rod having seven 0.059-in.-diam holes drilled radially through it. The total "hole" volume is 0.078 cu cm. When the rod is properly aligned, the holes in it constitute the "diaphragm" through which diffusion occurs. The center section was of Teflon and the rod and face plates were of Plexiglas. Four such cells were constructed and used in this study. Subsequent to this investigation, a similar cell constructed entirely of iron was fabricated and tested at higher temperatures. Several considerations led to this final design. It is desirable to minimize the volume of the cell chambers to decrease the time required for a measurement. However, the total volume of metal in the diaphragm must be small in comparison with that in the chambers. To facilitate filling and emptying it is desirable to have a diaphragm which may be closed.

Jan 1, 1970

By L. F. Mondolfo

An investigation of the relationship between properties of the elements and type of binary diagram formed was conducted. It was found that, for each type of equilibrium diagram, the factors for the size, valence, electronegativity, period, melting point, entropies of fusion, and sublimation calculated for each pair of elements cover a range of values. However, these factors show sufficient relationship to the equilibrium diagram so that the correlation of several of them can be used to predict the type of diagram formed, or at least limit the choice to only a few types. ThE goal of the metallurgist concerned with alloy development has always been to find a method that predicts the properties that can be obtained when a certain metal is added to another one. In most cases a qualitative predictiton of properties can be made if the equilibrium diagram is known. However, this means that for new metals the alloy development has to start with the experimental determination of the equilibrium diagrams. Because this determination is at least as complicated and time-consuming as the determination of the properties themselves, most alloy development has taken place by trial and error, and the study of the equilibrium diagrams has followed rather than preceded the creation of new alloys. Alloy structures and properties depend on the interaction between electrons and a complete knowledge of these interactions would permit prediction of structure and properties of alloys. Unfortunately direct measurement of these interactions is extremely difficult and somewhat doubtful and only properties that depend on them can be measured easily and with certainty. Study of the relationship between properties of the elements and equilibrium diagrams is not new. Besides the well known Hume-Rothery rule of the necessity of an atomic diameter fit within 15 pct for extensive miscibility in the solid, and the wide knowledge of the effect of such factors as size, electronegativity, electron-atom ratio on solid state features,"' work relating to liquid state and liquid-solid reactions can be found in the literature. Of particular interest is the work by Axon,3 who investigated the effect of size and melting point on a selected number of eutectic and monotectic dia-

Jan 1, 1962

By George E. Thackray

In December, 1894, the Cambria Iron Company made a number of heats of Bessemer steel to be used in structures by one of its customers, subject to inspection and tests by a firm of consulting engineers, one of the requirements being that the material should riot exceed .08 per cent. of phosphorus. In other respects the requirements were such that they could only be met by material of good quality; but the general spe cification is not introduced here, as it is not the purpose of this paper to deal with anything except certain difficulties encoun tered in determining the phosphorus-content of the material in a manner satisfactory to both seller and buyer. Preliminary determinations of phosphorus were made in sample-ingots from each of the heats from which material was rolled for the order in question, and these preliminary chemical tests, made in the laboratory of the Cambria Iron Company, showed that, with very few exceptions, every heat was within the prescribed limit of phosphorus. After the material had been rolled, sample-drilling8 of finished material were taken from the various heats in the regular manner in use at the works, these samples being thoroughly mixed and divided into two parts, one of which was analyzed at the works' laboratory and the other sent to the inspecting engineer. Several hundred determinations were made from this mate rial without reaching an agreement between the work of the inspector's chemist and that of the works' chemist; but as it is not the object of this memorandum to treat of this part of the subject at length, it is considered sufficient to present herewith only a few of these first determinations. The analyses given in Table I. are those of the original series made on the heats which were afterwards resampled for final determination by an arbitrator; and they are selected for this reason, as the entire " comparison is thus rendered more complete.

Jan 1, 1896

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By L. G. Jones, A. S. Odeh

A theoretical developtment is presented which provides a straightforward method of handling the drawdown analysis for both oil and gas wells flowing at variable rates. In the past our inability to analyze variable-rate drawdowns has been a major obstacle in using them for formation evaluation. This method should permit wider use of these tests in the future. INTRODUCTION Pressure build-up analyses are widely used to obtain reservoir data such as the effective flow capacity of the formation. On the other hand. although pressure drawdowns have been run for a long time, they have not been used extensively to evaluate reservoirs because they are difficult to analyze. One of the difficulties in analyzing pressure drawdowns has been that the theory developed until now has required the test to be run at a constant rate. For both oil and gas wells this is a difficult requirement to satisfy. especially during the early period of a well's life when drawdown tests are usually run. In spite of this limitation, drawdown tests are often run with build-ups as a check. In this paper a theory, which handles the drawdown analysis for variable rates, is presented for both oil and gas wells. Thus, one of the biggest deterrents to running drawdowns is removed, and they should become a much more useful engineering tool in the future. THEORETICAL CONSIDERATIONS 011, RESERVOIRS The general equation used for describing the unsteady-state radial flow of slightly compressible fluids in homogeneous porous media can be written in cylindrical coordinates as where r is the radial distance in cm, t is the time in seconds, p is the pressure at r and t in atmospheres, + is the fractional porosity, p is the viscosity in cp, c is the compressibility in vol/vol/atm, and k is the permeability in darcies. There are a number of solutions of Eq. 1 for various boundary conditions. One of these is the so-called "point-source" solution, which approximates the case of an infinite oil reservoir with a well located at r = 0 and produced at a constant rate. The point-source solution of Eq. 1 is

Jan 1, 1966

By C. F. Weinaug, P. M. Blair

Many difference equations used to approximate reservoir flow problems treat the phase pressures implicitly but not the mobility-density coefficients. Such difference equations are neither wholly explicit nor implicit, but might be described as mixed. Mixed equations are relatively easy to apply. But the associated time truncation error is relatively large, and when used to solve problems characterized by high flow rates, these equations may be unstable for practical size time steps. This paper outlines the development of a completely implicit difference analogue for reservoir simulation, along with a Newtonian iterative method for solving the resulting nonlinear set of algebraic equations that arise at each time step. While this implicit equation requires two to three times more work than does the mixed equation, it is shown to markedly decrease the time truncation error and to yield a stable solution for much larger time steps than does the mixed equation. INTRODUCTION Calculation of multiphase, multidimensional flow in porous media is generally accomplished by numerical methods that involve approximating systems of partial differential equations by systems of partial difference equations. The early development of difference equation techniques was directed toward the solution of linear differential systems. However, the equations of multiphase fluid flow through porous media are highly nonlinear in that mobility and density often are strong functions of pressure and saturation. Thus, solution of the flow problems by difference equations involves solving sets of algebraic equations whose coefficients change from step to step of the calculations. Current practice is to evaluate most coefficients at the beginning of a time step and then to apply difference methods well suited for solving linear problems. At least two major difficulties arise from the use of this practice. First, evaluation of coefficients at the old time level and evaluation of pressures at the new time level results in larger time truncation errors near displacement fronts than if all quantities in the distance derivative were evaluated at the same time level. Second, evaluation of mobility coefficients at old time levels results in an unstable difference equation in regions of high flow rate. The first of these difficulties often results in optimistic recovery behind the displacement front, and the second requires the use of small time steps or special techniques in solving coning problems1 or problems of gas percolation.2 Evaluation of all quantities in the distance differences at the new time level results in a completely implicit difference system. Such a difference system has a lower time truncation error than equations in which mobilities are evaluated at the old level and pressures evaluated at the new level. The algebraic equations resulting from the fully implicit difference equation are, in this case, nonlinear and require some iterative method for their solution. This paper develops fully implicit difference equations for two-phase flow in porous media, describes their solution by Newtonian iteration, and gives examples of problems more easily solved by the new method than by previous methods. EVOLUTION OF DIFFERENCE EQUATIONS FOR NONLINEAR PROCESSES The completely implicit difference equation used in these calculations results from evolution beginning with explicit difference equations, proceeding through what we will call "mixed" equations, and arriving now at a completely implicit equation. Let us illustrate the evolution by considering different analogs of the nonlinear equation

Jan 1, 1970

By Frances Jane Cromwell, D. J. McAdam, G. W. Geil

INTRODUCTION IN a series of papers, the authors and their associates have shown that the technical cohesion limit is affected by the same four factors that affect the flow stress, namely, the stress system, plastic deformation, temperature, and the strain rate.16-28 Moreover, each of these factors affects the technical cohesion limit in the same way that it affects the flow stress.‡ The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into use with the same significance as "technical cohesion limit," the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. This paper presents the results of an investigation of the flow of notched and unnotched specimens between yield and fracture. A study has thus been made of the flow and fracture of metals as affected by the stress system, and of the ductility of metals as affected by the stress system throughout plastic deformation. Since two of the principal stresses were equal (S2 = S3), the stress systems can be represented in terms of the radial stress ratio, the ratio of the transverse radial stress S3 to the longitudinal stress Sl.* The results of the experiments are represented by a series of complete flow-stress curves for each of the metals investigated, and these diagrams have been used for the development of other diagrams of various types. Ludwik was the first to suggest that fracture occurs when the flow stress becomes equal to a technical cohesion limit. Although Ludwik was incorrect in his view that the technical cohesion limit depends only on the amount of plastic deformation and not on the stress system, he was correct in his view that the flow-stress curve for any stress system terminates at a point representing a technical cohesion limit. The authors have seen some recent references to assertions by other investigators that a point representing the fracture stress need not be on the flow-stress curve. The Ludwik principle, however, would seem to be axiomatic, provided that the flow stress and fracture stress are properly defined and that the fracture stress is properly determined. Disregard of this principle has led to some untenable theories of criteria for fracture. When a metal is very ductile, the conventional method of determining the ductility and fracture stress by dividing the breaking load by the sectional area after fracture, generally gives values that are much too high. With some metals and in some conditions, the fracture stress thus determined may be two or more times the

Jan 1, 1948

NEW MEMBERS The following list comprises the names of those persons who became members during the period Sept. 10, 1916, to Oct. 10, 1916. BLOOMFIELD, EDWIN CHARLES, Min. Engr., 1012 Standard Bank Bldg., Vancouver, B. C., Canada. BRINGS, HENRY, Min. and Met. Engr., Chief Engr., and Geol., Mollet-Mesrine, 1212 Mills Bldg., El Paso, Texas. CHASE, MARCH F., Vice-Pres., Commercial Acid Co., 1906 Boatmens Bank Bldg., St. Louis, Mo. CUMMINGS, ALVIN M., Asst. Mine Supt., Witherbee, Sherman & Co., Inc., Mineville, Essex Co., N. Y. DOUGLASS, GEORGE M., Genl. Safety Inspector, Amer. Smelt. & Ref. Co. 120 Broadway, New Fork, N. Y. EMRICH, CLARENCE T., Chief Chemist, Old Dominion Copper Min. & Smelt. Co., Box 1163, Globe, Ariz. GARDANIER, SUTTER ALBERT, Assayer, Mgr., Douglas Assay Co., Douglas, Cochise Co., Ariz.

Jan 10, 1916

By T. G. Decker, A. F. Witt, A. M. Gaudin

The historical development of the concept of contact angle hysteresis is reviewed. The measurements of contact angles reported in literature have all been made under static conditions. For the measurement of dynamic advancing and receding contact angles, four methods are described together with an evaluation of their precision. Three of these methods were adapted from devices already used for the measurement of static contact angles. The fourth method uses a new principle and apparatus and is the most accurate. While the relationship between surface tensions and the contact angle was extablished as early as 1805 by T. Young,' it was only in 1890 that the existence of contact angle hysteresis was reported by Lord Rayleigh. His observations, however, remained almost unnoticed. With the invention of froth flotation, the contact angle and its behavior became the subject of investigation. In 1907, L. Sulman and collaborators investigated the cause of discrepancies between recorded values of contact angles. They found that certain variations existed in most cases, but that definite maximum and minimum values of contact angles are obtainable. The difference between the maximum and the minimum contact angle in a given system was termed "hysteresis" by Sulman. First attempts to explain hysteresis were made by E. Edser. In the following years extensive studies of contact angles in various three-phase systems

Jan 1, 1963

By D. K. Deardorff, Earl T. Hayes

An improved technique is described for the accurate determination of melting points of metals in the temperature range 1500' to 2500°C. The improvements consist of gradient heating and refinements in cavity preparation to obtain true black-body conditions. The melting point of hafnium, as determined by this method, is set at 2222°±30°C. This is over 200°C higher than one of the values reported earlier. Discrepancies in the previously reported values for the melting point of hafnium are explained. The melting points of zirconium and titanium are found to be 1855O±15OC and 1668°±10°C, respectively. Reproducibility of results was ±3OC. PRIMARILY, this report is being made to correct a 1975o±25oC1 value for the melting point of hafnium, and to present an improved method for melting point determination. As a matter of interest, the technique was also applied to determining the melting point of zirconium and titanium. There is a wide difference in the melting point of hafnium as reported by competent investigators. DeBoer and Fast' reported a value of 2230°±500C, and later work of McPherson, as reported by Aden-stedt, placed the melting point at 1975o±25oC. Zwikker" calculated that the melting point was 2430°C. In resolving this discrepancy, improvements were made in the procedure for determining the melting points of refractory metals in the range 1500" to 2500°C. Special techniques are necessary to determine the melting point of these metals accurately. Since the metals oxidize in air above 900oC, the determinations must be carried out in an inert gas or vacuum. Also, every known refractory contaminates them to some extent. In addition, the attainment of true black-body conditions is always difficult. DeBoer and Fast actually determined the melting point of Hf-Zr as-deposited iodide process alloys and extrapolated to 100 pet Hf. McPherson employed a tungsten wire suspension similar to that described by Schramm, Gordon, and Kaufmann,1 and used hafnium metal produced by the iodide process. There was no apparent reason for the wide spread in melting points, since the quality of the metal was very good and the work was under the direction of highly competent investigators. Retracing some of this work revealed one understandable error in the case of hafnium, and led to development of an improved technique for determining melting points of reactive metals in the range 1500" to 2500°C. Material Crystal bar hafnium, zirconium, and titanium were used for this work, with analyses as shown in Table I. The hafnium was of the highest purity that has been prepared, though not as pure as the zirconium and titanium. At the instigation of the Pittsburgh Area Office of the AEC, a special lot of Hfo2 was purified, converted to the tetraflouride, and bomb-reduced with calcium, all at the Iowa State College Laboratories. This crude hafnium metal was then refined by the iodide process at the Foote Mineral Co. All specimens were cut with a Sic wheel, ground, pickled, and dried carefully before use. Procedure General Tungsten Suspension Method—In this method, a small specimen is suspended by a fine tungsten wire in a slender, induction-heated tungsten or tantalum cylinder, all under vacuum. The melting point is determined by heating the specimen slowly while observing it with an optical pyrometer focused upon a portion of the specimen that radiates as a black body. This means that there should be no reflected radiation, either from colder objects near the pyrometer or from hotter surfaces. The induction heater would be the only hotter object and, if it is slender enough, the specimen will attain the same temperature. Often a slender hole is drilled into the specimen as a source of black-body radiation. This was the general method used by McPherson in obtaining his value of 1975°C for the melting point of hafnium. In trying to repeat this work, it was found that the points of contact between the

Jan 1, 1957

The Institute conducts jointly with the American Society of Civil Engineers, American Society of Mechanical Engineers and American Institute of Electrical Engineers, certain activities as listed below, and is joint owner with them of certain properties. United Engineering Trustees, Inc. When Mr. Carnegie made his gift which made possible a home for the engineering societies, a separate corporation was organized to act as a holding company and to manage the common property. This was long known as the United Engineering Society, but the name has now hen changed to one which more nearly reflects the real function of the corporation. It holds title to the Engineering Societies Building and to various funds placed in its charge and is managed by a Board of Trustees, of which three are chosen by each of the four societies, American Institute of Mining and Metallurgical

Jan 1, 1932

By P. B. Knuckey, D. Littleford

The Kalengwa mine, situated in a remote area of Zambia in Central Africa, has presented some unique problems to the planners engaged in developing the deposit. This small, high grade copper deposit contains some 1,688,000 tons of ore at a grade of 9.3% contained copper. Of this 362,000 tons is classified as high grade ore at 27.2% Cu, the coarse fraction of which can be fed directly to converters; 733,000 is classed as intermediate grade ore averaging 6.3% Cu, and 593,000 tons classed as low grade ore containing 2.1% Cu. The geology of the deposit and the establishment of the mining operation is fully described. A concentrator is being built at Kalengwa to treat the high grade fine product, intermediate, and low grade ore, whilst the coarse high grade ore will be trucked to the Copperbelt smelters for direct smelting. Details of metallurgical processing are given. The decision to truck the coarse high grade ore to the smelters on the Copperbelt necessitated the construction of a new 200-mile road, the setting up of a fleet of heavy ore transport trucks and associated equipment. The remoteness of the area from established communication facilities on the Copperbelt necessitated the provision of radio communications between Kalengwa and the head office at Kalulushi, and the establishment of a regular mine air service. The paper also describes the training of an unsophisticated local population in the operation of heavy plant and machinery, the establishment of the township, and the provision of health services.

Jan 1, 1972

By Luiz C. Correa da Silva, Robert F. Mehl

A. D. Le Claire and R. S. Barnes (Atomic Energy Research Establishment, Harwell, Didcot, Berks., England)-—This much awaited paper admirably confirms that the Kirkendall effect is a true diffusion phenomenon and likely to be found in all diffusing systems. The most likely explanation put forward so far to account for the shift of interface is that the two components of the system, diffusing in opposite directions, do so with unequal rates so that there is a net loss of material from that half of the diffusion zone rich in the more rapidly diffusing component. This loss is accompanied, and at least partly compensated for, by a closing up or decrease in volume of this latter half of the diffusion zone and an expansion of the other half so as to tend to keep constant the overall volume per atom. This is manifest as a movement of the original interface. If this is a true picture of what is taking place then there are at least two important matters requiring further study."1—The quantitative relating of the observed shift with the independently measured separate diffusion coefficients of the two diffusing species."2—A detailed study of the mechanism and characteristics of the closing up process."We would like first to make a few remarks pertinent to these topics. In connection with the first of these, it is a pity that more and detailed measurements were not made on the Au-Ag system, the only one for which the separate diffusion coefficients of the two species have been measured.'" One of us (A. D. Le C.) has calculated from Johnson's results the shift to have been expected in samples D.2 and D.3. Darken4 showed that the velocity v with which the markers move is related to the separate diffusion coefficients Dau, Dag, by the eauation:"dN"v = (Dag — Dau "dx"dN"where .is the concentration gradient at the mark-ax"ers. Under certain conditions,4, 20 it can also be shown that:"Xm"v = "2t"where x, is the total marker shift after time, t:"dN". . xm = 2t (Dag — Dau) [9]"dX"Johnson measured Dag and DAu in a chemically homogeneous alloy and so his reported figures represent the true or ideal diffusion coefficients"; the same quantities in eq 9 represent the actual diffusion coefficients as would be measured in the presence of a chemical concentration gradient, so we need to multiply Johnson's reported values of Dag and Dau by the"1 before insert-dlogN "ing them in eq 9. 7 is the activity coefficient of Ag at the concentration prevailing near the markers which we shall assume to be - 50 pct. The values of the thermodynamic factor for N = 0.5 and the temperatures at which D.2 and D.3 were annealed were obtained from thermodynamic data quoted by Darken.' aN/ax was computed from the coefficient of inter-diffusion of Au and Ag given by Johnson on the assumption that in the samples D.2 and D.3, the concentration distance curve could be represented by the standard equation:""No is the original difference in concentration between the two halves of the couple, and + is the error or probability function."aN/ax at x = 0 is then given by:"adN/dx "2/nDt"and we assume that this represents the concentration gradient at the markers, although it is probable that the figure is slightly high."When all the appropriate quantities are inserted in eq 9, we find that the expected shifts are: for D.2, 0.0134 cm and for D.3, 0.0119 cm."The agreement between these results and those

Jan 1, 1952

By Hugh S. Spence

IN the winter of 1941-42, muscovite mica was discovered by a young prospector, Justin Purdy, in the township of Mattawan, Nipissing District, Ontario, a few miles north of the small settlement of Eau Claire, which lies on the main Transcontinental Highway (No. 17) between Mattawa and North Bay. Muscovite had been known for many years to occur in the general Mattawa region, and various small efforts at production had previously been made by individuals working scattered deposits in the area. These minor activities, however, had never led to production of any consequence or the discovery of any important mica bodies. The Purdy finds were made in a heavily timbered, mountainous area lying about three miles north of the low-lying settled land along the highway, and in a section not hitherto prospected. The mica taken by Purdy and two partners from surface outcrops proved so remarkable in point of size of trimmed sheets that the find attracted considerable attention, and the area surrounding the three claims taken up by the prospectors was quickly blanket-staked by various interests. Though a number of other mica-bearing pegmatite dikes were 'found later on these stakings, none proved as rich as those on the original Purdy ground; very little commercial mica was obtained from them and attempts to develop them were short-lived. Purdy and his partners sold their initial production to dealers in Ottawa and Hull, where the Canadian mica industry long has centered. Young Purdy, unfortunately was killed in a motor accident in the early summer of 1942. His father continued mining operations for a few months and produced and sold a considerable amount of mica. In October 1942 the Purdy holdings were acquired by Inspiration Mining and Development Co. of Amos, Quebec, which had been active in staking in the area. This company formed a subsidiary, Purdy Mica Mines, Limited, to develop the property. Under the energetic management of Joseph R. Norrie, rapid progress was made, and production soon attained important proportions. Realizing from the outset the unusual character and potential value in the war effort of the Purdy discovery, the Metals Controller, Department of Munitions and Supply, at once arranged with the Department of Mines and Resources for an official geological report on the area, and also drew the attention of the War Production Board in Washington to what seemed likely to prove a highly important source of strategic-quality mica. Officials of WPB were sent up in the summer of 1942 to inspect the property,

Jan 1, 1947

By Martin E. Chenevert

The early work of Terzaghi1 showed that the true stress state of a rock can be expressed by the principle of effective stress. This principle states that effective stress is equal to total applied stress minus the pore pressure. Since the introduction of this principle, a great effort has been made to measure the pore pressure of rocks so that the true stress state can be determined. For clean, permeable sandstones, it is usually found that the effective stress principle can easily be applied. Direct measurement of the pore pressure is achieved with a hydraulic pressure device and the effective stress state thereby computed. However, for fine-grained rocks which contain large amounts of clay (referred to herein as shales), pore pressure measurements are usually quite difficult because of the adsorptive forces of the clay platelets, which produce negative internal pressures. No suitable device is known for measuring internal pressures of dry shales; the effective stress approach is therefore not feasible and data are usually presented in another form. As an example, data from compressive strength tests are presented as a function of rock wetness, rather than effective confining stress. The work of Belopoloskii2 and Colback and Wiid3 are examples of such data. It was pointed out by Lambe and Whitman4 that a better way must be found to express the effective stress of argillaceous rocks. The information presented herein is an attempt to fill that need. Various authors have been able to measure moderate negative pore pressures (0-240 psi) within rather wet, argillaceous rocks by means of various pore pressure devices. In 1961 Lambe5 resented information which shows that pore pressures in argillaceous rocks are indeed negative ; he presented values of suction pressure as low as - 14 psi. Likewise,

Jan 1, 1970

By Thomas V. Falkie

The use of operation research and computer techniques in the mineral industries continued to gain acceptance during 1966. There are generally at least five sources of information for researchers and practitioners in the field: (1) Technical periodicals like MINING ENGINEER- ING, Mining Congress Journal, etc. (2) Proceedings of the Symposium and Short Course on Computers and Operations Re- search in Mineral Industries, held last year at Penn. State University and jointly sponsored by the University of Arizona, Stanford University, Colorado School of Mines, Penn. State University and the Society of Mining Engineers of AIME. (3) Various local conferences, such as the 1966 Rocky Mountain Minerals Conference held in Denver. (4) United States Bureau of Mines publications. (5) The AIME annual meeting in New York and the SME Fall Meeting in Tampa.

Jan 2, 1967

By Donald W. Gentry

The recently established SME-AIME Education Board has completed its first full year of operation, and its six constituent committees-Accreditation, Career Guidance, Continuing Education, Educational Statistics, and Scholarship-have been extremely active in identifying and initiating programs to serve the educational needs of the Society of Mining Engineers and its members. The Continuing Education Committee-primarily concerned with the needs and problems associated with providing a continuing education program for SME members-is responsible for: (1) determining the need for short course offerings; (2) developing needed courses, along with new means and opportunities of presentation; and (3) scheduling and evaluating course presentation. In response to this charge, the committee has sponsored two short courses at the SME-AIME Fall Meeting in St. Louis and three short courses at the AIME Annual Meeting in Denver. Its major effort, however, has been directed toward the 1978 SME-AIME Fall Meeting to be held in Orlando, Fla., where 18 days of short-course instruction have been scheduled. A portion of these courses will be presented prior to the meeting, with the remainder to be presented in Nassau, Bahamas, immediately following the meeting.

Jan 7, 1978