Search Documents

By C. S. Barrett, A. Smigelskas

There have been no publications of the deformation and recrystallization orientations of the metal beryllium, yet pronounced textures would certainly be anticipated since it is close-packed hexagonal in structure. Having an axial ratio approximately that of magnesium, beryllium probably deforms by nearly the same slip and twinning mechanisms that operate in magnesium, and the textures are likely to be similar or but slightly different from the magnesium textures. In the tests reported below this is found to be the case; the textures are found to differ from those of magnesium only in the details of the scatter from the average orientation. This report covers not only samples rolled at room temperature, but some rolled at elevated temperatures. Since magnesium has been suspected by some investigators of altering its crystallo-graphic deformation mechanism at elevated temperatures, it was considered possible that beryllium might do so and alter its textures accordingly. No pronounced alterations were found, however. Unfortunately, the theory of deformation textures is not in a state of development that permits one to deduce the deformation mechanism from a knowledge of the textures, which means that the similarity of textures at different rolling temperatures, reported here, cannot be taken as definite evidence that the deformation mechanism is actually the same at all temperatures. The general similarity of the deformation textures of magnesium and beryllium also extend to the recrystallization textures of the two metals, judging by the pole figures for recrystallized sheet presented in this report. Samples were prepared in the form of composite sheets made up of small pieces stacked in a pile. Each piece was trimmed with scissors so that an edge was parallel to the rolling direction, dipped in paraffin, and assembled into the pack by aligning it under the cross hair of a microscope. As the desired orientation was obtained on each piece it was secured in place by touching with a hot wire to melt the paraffin. A stack of ten or fifteen pieces was built up in this way, then trimmed to the shape of a T; the portion to be X rayed was then etched to the shape of a wire about 0.045 in. diam with 6N HCl. This method of shaping the sample is a modification of that used by Bakarian on magnesium.' The absorption of the rays in the sample was so slight that it caused no difficulty in interpreting the films. Exposures were made with a 0.030 in. diam pinhole, using molybdenum radiation (40 kv, 25 ma, Type A film at 5 cm, 2 to 3 hr exposures). With the recrystallized specimens it was found necessary to oscillate the specimen so as to reduce the spottiness of the lines. A range of oscillation of 5" was SUB- cient to produce reasonably satisfactory patterns, though the quality was somewhat inferior to that of the deformation texture patterns, and only two degrees of intensity were read from the arcs on the films. Typical photo-grams for each of the deformation textures and the recrystallization texture are assembled in Fig 1. The pole figures were plotted in the usual way with the intensity of the various portions of the diffraction rings estimated by eye. Seven to nine films were made of each sample and each was carefully read in plotting the pole figures. Typical series included exposures with the beam normal to the rolling direction and at 11, 26, 41, 56 and 71" to the cross direction, plus two exposures with the beam normal to the cross direction, and at 11 and 79" respectively to the rolling direction. The rolling was in each case considered sufficient to develop the final texture: the reduction by cold rolling was 84 pct (from 0.0045 to 0.0007 in. thickness), following prior hot rolling in longitudinal and transverse directions and recrystallization; the reduction by hot rolling at 800°C was 90 pct (0.010 to 0.001 in.), following similar prior treatment; the reduction by rolling at 350°C was 88 pct (from 0.005 to 0.0006 in.) after similar prior treatment. The recrystallization texture was determined on a sample rolled at 350" to a reduction of 88 pct (0.0165 to 0.002 in.) after similar prior treatment, then mounted between steel strips to keep it flat and annealed at 700" in an atmosphere of argon. Discussion of Results The results of the X ray determinations are assembled in the pole figures of Fig 2, 3, 4 and 5 for rolling at

Jan 1, 1950

By Paul M. Tyler

OF THE 92 elements generally accepted by chemists as constituting the primary building blocks of matter, all but the very rarest have been investigated with a view to employing them in steel manufacture. The surprising thing is that so few have been found commercially acceptable. Despite the relatively small number of elements involved, the use of alloys in steel making is one of the most complicated and probably one of the least well understood of modern industrial enterprises. The action of individual elements in steel making has been described often and a profuse and somewhat acrimonious literature covers pretty much the whole field of ferroalloy ore supplies. In the middle ground between the miner and the -steel maker developments are less carefully watched by most observers and except for an occasional description of the technique of some conversion process or the tariff hearings in Congress, little is said about them. The present paper has been submitted in the hope that it will stimulate broader constructive economic thinking. It undertakes to describe in' relatively nontechnical terms this great and growing though highly complex industry and to study its relations to national progress.

Jan 1, 1932

By J. H. Brophy, A. L. Prill, H. W. Hayden

An error lzas been found in the conventional way of determining the time exponent of linear shrinkage for the solution-precipitation stage of liquid-phase sintering. Large amounts of shrinkage due to initial rearrangenzent result in erroneously low exponents and tni si dentification of the rate-controlling process. Two alternative, mathematically correct, methods of calculation are applied to existing data on Fe-Cu, WC-Co, and Tic-Ni-Mo. This results in reidentifi-cation of the rate-controlling process and somewhat better agreement with related data. In each case the solution-precipitation process is solution-controlled and not diffusion-controlled. THE liquid-phase sintering process has been the object of a considerable amount of research for many years. Linear shrinkage vs time data at various sintering temperatures have been used recently in an attempt to identify the prevailing mass-transport processes in a number of metallic and nonmetallic systems. There is an analytical error inherent in the methods previously used for handling data during the "solution-precipitation" stage of shrinkage which must be recognized before the correct rate-controlling processes can be determined. It is the purpose of this paper to show how the error has affected previous conclusions and to suggest corrections. A number of mechanisms have been proposed to explain experimental observations during sintering in the presence of a liquid phase. The earliest of these is due to Price, Smithells, and williamsl who attributed the observed growth of the solid phase to the simultaneous solution of smaller particles and growth of larger particles. From the work of Lenel et al.2,3 and Gurland and Norton4 has come the suggestion that the liquid-phase sintering process may be divided for analysis into three steps: 1) rearrangement upon formation of the liquid phase; 2) solution and reprecipitation of the solid phase in the liquid; and 3) "coalescence" or a final stage of sintering, characteristically slower than the solution-precipitation process. The sequence of steps is shown schematically in Fig. 1. Kingery5 presented a thermodynamic and kinetic analysis of the first two "stages" of the liquid-phase sintering process in which the functional dependence of lineal shrink- age on time at temperature was used to identify the rate-controlling mass-transport process. Table I summarizes the time dependences and processes considered by Kingery.5 This method of data presentation has been employed by Kingery and coworkers for Fe-CU,6 WC-Co, and a number of nonmetallic systems," and bv Whalen and Humenik for Tic-Ni-Mo and Fe-cu.8 In each of these studies, the rate-controlling step during the "solution-precipitation" stage was identified from the slope of the curve in that stage on a logarithmic plot such as Fig. 1. However, in all of the previous studies, at a certain composition, relatively large amounts of shrinkage due to rearrangement preceded the solution-precipitation stage. Under these conditions, the larger the amount of rearrangement shrinkage the

Jan 1, 1965

By Tenney, J. B.

DEVELOPMENT of complex ores in the south- western part of the Rocky Mountain region has been retarded by the prohibitive distance to the nearest suitable zinc treatment plants. In the north- western and central Rocky Mountains the building, cluring tlie past decade, of electrolytic zinc plants at Anaconda, Great Falls, Trail, and Burke has tremendously stimulated the mining and exploiting of such .ores, greatly increasing the production of lead, zinc, copper, gold, and silver. Selective flotation permits the making of high-grade led, copper, and zinc concentrates. If the zinc concentrates could be made free from lead, copper, gold, and silver, they could be shipped economically to Mid- Western retort plants designed for such concentrates. Unfortunately a considerable proportion of the precious metal content accompanies the zinc blende in the ores of this region. Although some of it is saved in 'retort residues, the treatment cost is thereby increased so materially and the proportion saved so small, that .concentrates of ordinary grade cannot stand treatment charges and freight.

Sep 1, 1928

By W. H. Davitt

While it is true that taxes, especially income taxes, whether they be federal, state, or local, are not usually thought of as a "cost" of doing business, it is equally true that these tax costs do reduce the distributable profits just as much as the cost of power, supplies, or labor. Therefore, the consideration given to taxes is often as important as that given to other costs. Hopefully you will recognize that, within certain limits, taxes can be controlled to an economic advantage. The tax laws as now imposed are quite complex. Many of these laws and the regulations thereunder involve many factual determinations, technical considerations, and specialized valuations that can best be made by people trained in the specific area concerned. A substantial amount of a tax liability turns on the proper consideration given to issues involving facts and principles which are peculiarly engineering in nature. The importance of these "engineering" issues in tax administration has been significantly increased in recent years by our rapidly advancing technology, automation, stepped-up mineral and oil exploitation, new industries such as electronics and nuclear power, and the extension of percentage depletion to all minerals. These specialized requirements incorporated in the law are so technical that full consideration can not be given by people with a non-engineering background.

Jan 7, 1974

By F. L. Toy, C. E. Sims

I. A. Sirel—I would like to ask Mr. Sims what would the preferred hot metal analysis be as far as manganese and silicon are concerned if you used specially made iron for this process instead of basic iron. C. E. Sims (authors' reply)—A preferred composition would contain somewhat less silicon than the basic pig iron used in these experiments. High silicon requires a large lime addition. Lime must be added in sufficient quantity to neutralize the silica formed and to leave an excess for dephosphorization. Manganese presents almost no problem in operation. It is almost completely oxidized and, in burning, develops considerable heat. The evidence indicates, however, that, in continuous commercial operation, there will be an excess of heat produced, and the bath will need to be cooled in some manner as by the addition of scrap or by utilizing the energy for the direct reduction of ore. There do not seem to be any serious limitations on composition of pig iron. One heat was made with an iron containing 2.27 pct silicon and the phosphorus finished at 0.007 pct. In another, the iron contained 0.45 pct phosphorus which was lowered to 0.019 pct. This indicates considerable leeway in composition. D. R. Loughrey—We are all very much interested in the recent discovery of very large deposits of iron ore both in Labrador and in Venezuela. I would like to ask Mr. Sims if the iron ore at either or both of these places is such that it would lend itself to the manufacture of iron suitable for use in the turbohearth. C. E. Sims-—According to my information, those ores are not essentially different from ores now used in this country for making basic pig. They should, therefore, be adaptable to this process. D. I. Brown—You have spoken about the leeway, or spread in analysis of the various irons you can use in the vessel. I would like to have you tell us, if you can, about the different kinds of steels which can be made in such a vessel. The turbohearth process, or it might more aptly be called pneumatic openhearth, is a little different from that used in most Bessemer shops and in the one in which I worked. If we had a blow in the air over 10 min, the boss was in the pulpit in a hurry

Jan 1, 1951

By I. Cadoff, J. P. Nielsen

The Ti-C phase diagram exhibits a peritectic point at 1750°C and 0.8 pct C, and a peritectoid point at 920°C and 0.48 pct C. The maximum solubility of carbon in a titanium is 0.48 pct. The 6 region containing the Tic compound (20 pct C) extends to 11 pct C at the peritectic temperature. THE interest in the Ti-C alloy system stems from the fact that carbon occurs as an impurity in titanium alloys when graphite electrodes or graphite crucibles are used in their melting. Since titanium-base alloys are still in the development stage, some virtue may be found in carbon addition to titanium. The Tic compound is currently emerging as an important powder metallurgy base constituent similar to the WC compound. Ehrlich' identified the phases and structures present in the Ti-C system. The peritectoid region of the phase diagram was investigated by Jaffee et al." A preliminary diagram based on theoretical considerations was proposed at the outset of this research." The Tic compound has been investigated extensively and has been reported on in a large number of papers. Experimental Procedure Arc-melted alloys of 24 compositions in the range 0 to 20 wt pct C were investigated using metallography, X-ray diffraction, and, for the liquidus and solidus regions, incipient and complete melting. All alloys were prepared from iodide titanium (New Jersey Zinc Co., 99.95 pct Ti minimum) and spectroscopic grade carbon (National Carbon Co.). To prevent carbon spattering during arc melting the carbon was encapsulated in titanium. For alloys containing less than 1 pct C the powder was inserted into a capsule formed by drilling a hole in the as-received rod. For higher compositions, capsules were formed from titanium sheet. Arc Melting: The charges were melted in the copper-hearth cold electrode furnace shown in Fig. 1. This furnace is similar in principle to the all-metal unit adapted for titanium melting at Battelle Memorial Institute.' The transparent pyrex walls giving unlimited visibility during operation and the multiple-

Jan 1, 1954

By M. E. Wadsworth, A. S. Peck

Infrared spectra disclose that oleic acid will not adsorb on the surface of pure beryl unless the mineral is first activated with HF. The adsorption of oleic acid on HF activated beryl is attributed to the hydrogen bonding of oleic acid monomers to F-surface bridging sites. These sites are formed as a result of the reaction of HF with chemisorbed water or surface hydroxyl. Characteristic infrared spectra of physically adsorbed oleic acid are correlated with flotation at different pH at temperatures of 25°C and 75°C for colloidal and -60-mesh particles. The usual mode of occurrence of the beryllium mineral beryl, Be3A12Si6O18, is in granite pegmatites as pale green, white, or yellow crystals. A dark green gem variety, emerald, may be found in the wall rock of pegmatite veins or in mica schist. The most important beryl deposits in the United States are in the Black Hills District of South Dakota, and several mountain ranges of central and west-central Utah contain potential commercial sources of this mineral. Several papers have been published concerning the flotation of beryl with different conditioning reagents. Kennedy and O'Meara1 reported on the essential use of HF in the flotation of beryl from different ores. The use of calcium hypochlorite to separate HF activated beryl from feldspar after flotation with an amine collector was made by Runke.2 A report on the activation of beryl with different cations using sodium oleate collector was presented by Viswa-nathan and co-workers.3 Flotation of beryl with sulfonate collector and different activating salts was employed by Fuerstenau and Bhappu.4 The role of the surface charge or zeta potential in the flotation of beryl with different collectors and salts was also extensively investigated.5"7 Previous infrared investigations by the authors8 disclosed that the orthosilicate beryllium mineral, phenacite, reacts with oleic acid to form a chemisorbed oleate monolayer on the mineral surface. Thus, chemisorption is the effective mode of adsorption in the phenacite-oleate acid flotation system. In contrast, neither chemisorption or physical adsorption of oleic acid occur on the surface of pure beryl as evidenced in this study. Efforts were subsequently made to determine the mechanism of activation and collector adsorption for HF pretreated beryl. EXPERIMENTAL PROCEDURES Large, white, terminated crystals of beryl were obtained from Madagascar through Ward's Co., Monterey, Calif. The crystals were broken into -60-mesh fragments in a porcelain mortar. Part of this prepared material was ground to a powder with a Fisher Grinder using an agate mortar and pestle. The powder was transferred to a graduated cylinder and mixed with 500 ml of distilled water. After 5 min, the colloidal suspension was separated from the settled particles by decantation and used as a stock for infrared test determinations. Adsorption tests were performed by first transferring 20 ml of colloidal suspension to 50 ml glass centrifuge tubes. The solids were then centrifuged out and the liquid was discarded. Then, the solids were pretreated with one molar HC1 or one molar HF. After 15 min, the solids were again centrifuged out. The mineral solids were washed free of residual acid by repeated centrifuging and water washing operations. Then, 20 ml of distilled water was added to the solids, and the resultant suspension was used for test purposes. In the preparation of mineral for flotation tests, 1.5 g of -60-mesh beryl was deslimed by removing the colloidal fraction by three successive water washes and decantations. Then, the coarse particles were pretreated with either one molar HCl or one molar HF for 15 min. The mineral was next washed free of acid with distilled water, and 20 ml of distilled water was added to the beryl prior to collector conditioning. The conditioning of mineral with collector was performed in 50 ml centrifuge tubes to which either NaOH or HC1 was added for pH modification. One drop (6.0 mg) of U.S.P. reagent grade oleic acid or 2 ml of 0.01 molar sodium oleate was added to the pulp and stirred at about 1500 rpm for 3 min at a

Jan 1, 1968

He took a great interest in technical matters and his inclination was strongly toward research investigations. At the same time he was effective in manual and mechanical work and was generally found working side by side with the men under his direction. His nature was unselfish and he was extremely popular socially. He was a member of the Coeur d'Alene Commandery, Knights Templar. Stanly A. Easton. Lieutenant.Louis Baird Louis Baird, a Lieutenant in the Royal Field Artillery of the British Army, died on the battlefield in 1915. Lieutenant Baird was born July 28, 1880, at Stirling, Scotland. His technical education was obtained at King's College, Melbourne, Australia, in 1893 to 1895, and at the Technical College at Glasgow, Scotland, in 1897 to 1900. After an apprenticeship with the Mexican J. & 8. Rec. Co. of Mexico, lasting from 1900 to 1903, he became mill superintendent for the Cia. Minera Benito, at Juarez, Zac. During the year 1905-6 he was assistant manager of the Candelaria y Anexas, at Pinos, Zac., and from 1906 to 1907 was engineer with the Cia. Minera Jalisco, San Sebastian, Jalisco. At the time of his admission to the Institute, in 1908, he was practising as a mining engineer at Etzatlan, Jalisco, Mexico. For the next four years he practised his profession in the City of Guadalajara, Jalisco, removing, in 1913, to Ixtlan del Rio, in the State of Tepic. It was from here that he returned to England to put his services at the disposal of the British Government. The Institute is not definitely informed as to how, where, or when Lieutenant Baird met his death. Captain John H. Ballamy John H. Ballamy, Captain on the Regimental Staff of the 103d Engineers, was killed near Fismes, on Aug. 9, 1918. Captain Ballamy was born at Plvmouth. Pa.. in 1886 and graduated from' the High School of that town in 1903. In the following year he began work as a coal miner, and at the same time began the study of mining engineering in the evening and any other spare time. He continued this diligent and energetic practice for many years. For sixteen years he continued in the employment of the Delaware, Lackawanna & Western Rai1roa.d Company's coal mining

Jan 1, 1920

Frank Clemes Smith, Deadwood, 8. D. (communication to the Secretary): The reading of Mr. Chance's interesting paper suggests a few ideas relative to his discussion of certain Black Hills gold-ores. Mr. Chance refers to his examination, in 1897, of " the (Carboniferous) limestone plateau-country which encircles the central area of the Black Hills," and says that " it had been generally assumed that the mineralization of this formation was confined to the northern area;" further, that he "found, however, a general mineralization, extending in zones or belts throughout the region," and that the ores, being more or less specially

Jan 1, 1900

By R. R. Webster, H. T. Clark

I. A. Sirel—I would like to ask Mr. Sims what would the preferred hot metal analysis be as far as manganese and silicon are concerned if you used specially made iron for this process instead of basic iron. C. E. Sims (authors' reply)—A preferred composition would contain somewhat less silicon than the basic pig iron used in these experiments. High silicon requires a large lime addition. Lime must be added in sufficient quantity to neutralize the silica formed and to leave an excess for dephosphorization. Manganese presents almost no problem in operation. It is almost completely oxidized and, in burning, develops considerable heat. The evidence indicates, however, that, in continuous commercial operation, there will be an excess of heat produced, and the bath will need to be cooled in some manner as by the addition of scrap or by utilizing the energy for the direct reduction of ore. There do not seem to be any serious limitations on composition of pig iron. One heat was made with an iron containing 2.27 pct silicon and the phosphorus finished at 0.007 pct. In another, the iron contained 0.45 pct phosphorus which was lowered to 0.019 pct. This indicates considerable leeway in composition. D. R. Loughrey—We are all very much interested in the recent discovery of very large deposits of iron ore both in Labrador and in Venezuela. I would like to ask Mr. Sims if the iron ore at either or both of these places is such that it would lend itself to the manufacture of iron suitable for use in the turbohearth. C. E. Sims-—According to my information, those ores are not essentially different from ores now used in this country for making basic pig. They should, therefore, be adaptable to this process. D. I. Brown—You have spoken about the leeway, or spread in analysis of the various irons you can use in the vessel. I would like to have you tell us, if you can, about the different kinds of steels which can be made in such a vessel. The turbohearth process, or it might more aptly be called pneumatic openhearth, is a little different from that used in most Bessemer shops and in the one in which I worked. If we had a blow in the air over 10 min, the boss was in the pulpit in a hurry

Jan 1, 1951

By PAUL AUDIBERT

THE downward trend of metal prices seems to act something like a reagent that precipitates selfishness in most business men's hearts; in the same way the upward trend precipitates altruism. Operators do not say: "I continue working my mine without curtailment because I can afford the present prices while my neighbor cannot and thus will give me way." They say: "I continue working my mine because 1 consider it a service for consumers. They will get better prices on a free market. Any curtail¬ment would be an attempt to raise prices artificially, that is to say, bad economics." Copper producers have learned how fallacious is such an opinion. It perhaps was not fallacious in olden times when all mines were worked on a small scale even if operating on a big deposit. At that time the supply and demand law played fair. When prices were too low and profits were vanishing for many mines, they would. shut at once, then little by little the metal scarcity would induce prices to climb up again; finally these prices would reach the point when it became profitable to again work the closed mines. Re-opening and shutting down mines was then a normal custom. Workers and operators weakly deplored this unstability, but there was nothing effective they could, do about it.

Jan 1, 1931

5. The medal committee may invite nominations from the membership of the Institute, such nominations to be accompanied by an argument in favor of the award and details sufficient for a proper citation to be drawn. This medal has been awarded as follows: 1927—David William Brunton. 1929—John Hays Hammond. 1928—Herbert Hoover. 1930-Daniel C. Jackling. Miscellaneous Prizes Many of the Local Sections have established or administer prizes for the best paper presented within the year by any junior member. Annual Lectures Howe Memorial Lecture The Howe Memorial Lecture, in memory of Henry Marion Howe, Past President of the Institute, was authorized in April, 1923, as an annual address to be delivered by invitation under the auspices of the Institute by an individual of recognized and outstanding attainment in the science and practice of iron and steel metallurgy or metallography, chosen by the Board of Directors upon recommendation of the Iron and Steel Division. The following were the Howe lectures and lecturers for the years indicated: 1924 What is Steel? By Albert Sauveur. 1925 Austenite and Austenitic Steels. By John A. Mathews. 1926 Twenty-Eve Years of Metallography. By William Campbell. 1927 Alloy Steels. By Bradley Stoughton. 1928 Significance of the Simple Steel Analysis. By Harry D. Hibbard. 1929 Studies of Hadfield's Manganese Steel with the High-power Microscope. By John Howe Hall. 1930 The Future of the American Iron and Steel Industry. By Zay Jeffries. Institute of Metals Lecture An annual lectureship was established in 1921 by the Institute of Metals and it has come to be one of the important functions of the Annual Meeting. A number of distinguished men from this country and abroad have served in this lectureship. The roll is quoted below: 1922 Colloid Chemistry and Metallurgy. By Wider D. Bancroft. 1923 Solid Solution. By Walter Rosenhain. 1924 The Trend in the Science of Metals. By Zay Jeffries. 1925 Action of Hot Wall: a Factor of Fundamental Influence on the Rapid Corrosion of Water Tubes and Related to the Segregation in Hot Metals. By Carl Benedicks. 1926 The Relation between Metallurgy and Atomic Structure. By Paul D. Foote. 1927 Growth of Metallic Crystals. By Cecil H. Desch. 1928 Twining in Metals. By C. H. Mathewson. 1929 The Passivity of Metals, and Its Relation to Problems of Corrosion. By Ulick R. Evans. 1930 Hard Metal Carbides and Cemented Tungsten Carbide. By 8. L. Hopt.

Jan 1, 1930

By W. E. Wrather

SERIOUS consideration was given by the Petroleum Division to a wide variety of subjects, during six busy sessions at the Annual Meeting. Beginning with a joint session on engineering research and production engineering, Tuesday afternoon, conducted by E. A. Stephenson and H. C. Fowler, problems of petroleum technology, domestic and foreign production, proved oil re- serves, economics, and stabilization were mooied almost without interruption until nearly everyone was "talked out,' and the meeting was adjourned at the end of the annual Petroleum Division dinner, late Thursday night.

Jan 1, 1933

Abramovits, Charles, Student. Case School of Applied Science Cleveland, Ohio. '37 Adams, Benjamin C., Jr Address Wanted. '36 Adams, Ernest C., Student, Univ. of Illinois 908 W. Green St., Urbana, Ill. '35 Adams, George H. 4021 Walnut St., Riverside, Calif. '36 Afshar, Hodji Khan ?A. Box 2072, Norman, Okla. '35 Ahlen, Louis S., Student, Univ. of North Dakota Univ. Sta., Grand Forks, N. D. '37 Ahrenholz, Herman William, Jr., Student, Lehigh Univ Bethlehem, Pa. '35 Alger, Robert P., Student, Missouri School of Mines & Met Rolla, Mo. '36 Alkire, Robert L., Student, Univ. of Pittsburgh Pittsburgh, Pa. '37 Alleman, Virgil C., Student, South Dakota School of Mines Rapid City, S.-D. '37 Allen, C. G., Student, Case School of Applied Science Cleveland, Ohio. '37 Allen, Eugene S., Student, Univ. of California Berkeley, Calif. '37 Allen, George W., Student, Michigan College of Min. & Tech Houghton, Mich. '37 Allen, Harry Berkley, Student, Univ. of California Los Angeles, Calif. '37 Allen, Henry, Jr., Student. Univ. of Arizona Sigma Chi House, Tucson. Ariz. '37 Allen, Paul W., Student, Mass. Inst. of Tech Cambridge, Mass. '35 Allen. R. M.. Jr.. Student. Virginia Polytechnic Inst., "G" Co Blacksburg, Va. '35

Jan 1, 1937

By William M. Sheehan

TRANSPORTATION is one of the most important problems of the mine operator and the possibilities of cost reduction in this field should not be overlooked. In the railroad industry, cars and locomotives have been improved greatly, and the progress there made is well worthy of study by the mine operator looking for maximum efficiency in every branch of his activities. One of the outstanding developments in the construction of railroad equipment in recent years has been the wide-spread adoption of large one-piece steel castings for the framework of locomotives, passenger and freight cars. Some of the advantages and applications of this type of construction will be outlined in this paper, with particular thought of the needs of the mining industry. The inherent qualities of cast steel: homogeneity, unrestricted size and shape, high tensile strength, flexibility of metal distribution, resistance to corrosion, and gracefulness of outline, make it the most versatile member of the ferrous group. Not only is it a strength-giving element, but it is corrosion resistant, a combination that makes for large economies in equipment maintenance. Flexibility of metal distribution allows the integral foundation to be in the shape best suited for the purpose. These cast structures are really assembled in the mold in liquid form and the metal can be placed in the right pro¬portion exactly where it is needed, thus securing weight economy and uniformity of fibre stress. Such a process permits the incorporation, with ease, of necessary brackets, utilizing them to provide not only greater strength for the derail part itself, but often to add to the value of the entire unit. Laps, seams, and joints, which are necessary in all fabricated forms, are eliminated.

Jan 1, 1933

By K. Huessener

INTRODUCTION THIS paper attempts a survey of the principles involved in the com¬bustion of blast-furnace gas in boilers and stoves. I do not expect to be able to give much information which is actually new, since the laws and methods of calculation pertaining to this problem are contained in a number of handbooks; but, so far as I am aware, they have nowhere been treated exclusively with reference to this one problem of gas economy. The road which I follow is less that of strictly scientific research than that of the practical engineer, faced by operation problems which require a. quick solution by easily accessible means without a prolonged search in scientific handbooks. For this purpose I give a number of tables and diagrams, as well as the results of many years' practical working experience as combustion engineer, which I trust will prove useful to my readers. HISTORICAL Considering the tremendous efforts made during the last 15 years to increase the efficiency of all kinds of power plants, it is highly surprising that until a comparatively very recent period, progress in the economical combustion of blast-furnace gas has been so slow. The explanation generally put forth, that fuel has been so cheap that it was hardly worth while to bother about this economy, will not hold good, for the greatest trouble was taken to improve the combustion of coal and to reduce the consumption of steam. The most plausible explanation appears to be the general impression, held as an accepted fact, that gas, especially hot, uncleaned, blast-furnace gas, was not a good boiler fuel. Many managers of high repute had tried unsuccessfully to improve the conditions of its use, and the dictum went forth that efficiencies of over 60 per cent., particularly with high loads, were impossible. This was the situation not only in the United States, with very cheap fuel, but also in Europe, where fuel prices are twice and three times as high.

Jan 2, 1916

By Ross E. BROWNE, Ross B. HOFFMANN

IT seems strange that a theory so devoid of value in its application to our practical problems should attract such widespread acclaim. This appears still more remarkable when one considers the foundation on which it is built. The criticism naturally suggested is as follows: First; the special theory of relativity is based on an assumption which is counter to the fundamental conception of relative motion. Second; the theory claims only a slight modification of Newtonian mechanics-a modification so minute that, even if true, it would have no practical value in its application to any visible occurrence here on earth.

Jan 1, 1931

For many years the occurrence of gold in the Coeur d'A1ène region had been rumored among the pioneers of the Northwest. It is stated that as early as 1853 gold was discovered in this district by Donelson, of the Stevens expedition, but the hostility of the Indians prevented prospecting. In 1858, when Lieutenant John Mullan surveyed the military road across the Bitter hot mountains, the members of his expedition, most of whom had mined in California, noticed sundry outcrops of good-looking quartz, and some of them actually found gold, as is recorded in a letter that Mullan wrote, from Washington, in 1884. The first successful prospector in the Coeur d' Alène was Tom Irwin, who worked a quartz vein on the Mullan road in the spring of 1879. Two years later he met A. J. Prichard, who was engaged in the lumber business; he told him what he thought of the chances of placer mining in the upper reaches of the Coeur d7AlBne river. This was in 1881. Prichard became keenly interested, and himself found gold on several creeks, one of which is now known by his name, at a place close to the site of the town of Murray.* In 1883 Prichard located a number of claims, and shortly afterward he wrote a letter to the members of a Liberal League to which he belonged, inviting them to "secure the lion's share" of the mineral wealth he had uncovered. His letters caused a stampede from Montana and Colorado, and from South Dakota also, to the Coeur d'Alène gold belt in the summer of 1883. A town, named Eagle City, was surveyed; in 1884 lots sold at prices ranging from $200 to $2000. The buildings were made of logs and shingles. Shoveling of the snow in' front left s

Jan 1, 1932

NEVADA SECTION J. W. HUTCHINSON, Chairman, FRANCIS CHURCH LINCOLN, Vice-Chairman, HENRY M. RIVES, Secretary-Treasurer, Reno, Nevada W. H. BLACKBURN, E. A. JULIAN, EMMET D. BOYLE, JOHN G. KIRCHEN, FREDERICK BRADSHAW, C. B. LAKENAN, TASKER L. ODDIE. The formation of the Nevada Section was originally suggested by Professor F. C. Lincoln, who had discussed the subject with Mr. William L. Saunders when the latter was President of the Institute. Professor Lincoln sought the assistance of the Nevada Mine Operators' Association, whose Executive Committee constituted itself a Committee on Organization, and authority for the establishment of a Nevada Section to include the entire State was secured from the Board of Directors of the Institute. The formal installation took place at 10 A.M. on May 18, Mr. William L. Saunders officiating. The Honorable Emmet D.. Boyle, Governor of Nevada (and a member of the Nevada Section), made the address of welcome. On the afternoon of the same day, a technical session was held, at which the following papers were presented: History and Development of the Cyanide Process Charles Butters Virginia City Whitman Symmes Ore Deposition at Steamboat Springs Prof. J. C. Jones

Jan 7, 1916