Search Documents

By W. L. Saunders

THE world's greatest producing area is, geographically, in the midland region of North America about the Great Lakes. This area, with but one- third of the nation's population, produces, with the exception of tobacco and cotton, three-quarters of the principal staples. It provides the surplus or export grain, meats, dairy products, steel and leading minerals. The social and political condition of a nation is determined by its industrial efficiency, and the share of the commerce of the world obtained by a nation is fixed more by the economy of its transportation than by any other factor. It is an economic maxim that: The total cost is the cost of production plus transportation cost. The cost of carrying 1000 tons by water or 100 tons by rail is equal, over the same distance

Jan 1, 1921

By Ove Rehnberg

Catalytic purifiers are widely used as exhaust treatment devices on diesel equipment in confined spaces. The paper summarizes some studies carried out at the University of Lulea on diesel exhaust purifiers. The main purpose has been to elucidate important chemical activities of catalysts useful for the improvement of their effect. The effects of platinum catalysts on exhaust constituents such as carbon monoxide, nitrogen oxides, unburned gaseous hydrocarbons, and polynuclear aromatic hydrocarbons are discussed. Also pointed out are the great differences in catalyst activity and advantages/disadvantages associated with the catalysts.

Jan 1, 1982

By Albert F. Hill

The manufacture of structural shapes in steel of uniform quality, which shall command the full confidence of the engineer, is a problem in practical metallurgy which is beginning to attract much attention in this country. The progress of the past fern years in the improvement of plant and processes has placed it within the power of the steel-maker to supply a material of such chemical composition as will meet the requirements; but this solves only in part the difficulties of the constractor. It is well understood that the influence of shop manipulations is a most decisive one upon the mechanical properties of the finished product; in many cases so great, in fact, as to cause an entire transformation in the character of the material, and to render it unfit for the service for which it was intended. On the other hand, mechanical treatment is frequently resorted to as an efficient corrective of certain undesirable properties, which may be due either to chemical composition or previous manipulation. This understood and accepted, it is evident that careful investigation of the effects of mechanical treatment is fully as necessary to the successful use of steel in engineering structures, as the investigation of the influence exerted by its chemical composition. All structural material has to undergo more or less mechanical treatment, such as shearing, punching, upsetting, etc. Each of these operations produces effects which are far more marked and decisive in steel than they are in iron, and means must therefore be adopted to counteract, or at least to modify, these effects before the material is permitted to enter the structure. The fact that both shearing and punching affect the tenacity and elasticity of steel has long been recognized; bat, through more recent investigations, it has been established that these effects are purely local, and are therefore susceptible of correction by other and simpler means than annealing. The importance of this discovery to the use of steel in structures is very great. The impracticability of

Jan 1, 1883

By Nathaniel Arbiter

THE separation of minerals by flotation can be regarded as a rate process, with the extraction of any one mineral determined by its flotation rate, and the grade of concentrate by the relative rates for all the minerals. So regarded, the significant variables for the process are those that control the rates. These variables are of two types, the first describing the ore and its physical and chemical treatment prior to flotation and the second characterizing the separation process in the cells. This paper will examine the variation in rates for a group of separations, will show that a simple rate law appears to govern, and will consider the relation of the control variables to the rates. The use of rate constants for evaluation of performance and efficiency will be discussed.

Jan 9, 1951

By John A. Church

IT is a well-known fact that under similar conditions a ton of pig iron can be made from any ore with less fuel when charcoal is used than when coke or anthracite is employed for heating. The cause of this superiority is entirely undiscovered, and no explanation has yet been offered which has won even temporary acceptance. Such as they are the hypotheses heretofore presented are of two general kinds, and they come from those two divisions of the working force which are so often antagonistic in all professions, the scientific and the practical men. The theory of the scientific men is drawn from the chemical reactions which are known to go on in the furnace, and it is well expressed in a recent paper by Prof. Akerman, of the Stockholm (Sweden) School of Mines. It makes the superiority of charcoal as a fuel in the blast furnace to depend upon its quick and thorough reduction of carbonic acid. This property belongs to charcoal in virtue of its porous structure. Its cells have a diameter of only one twenty-four hundredth of an inch, and one grain of charcoal has been computed to have a surface of two and four-tenths square feet. According to the theory in question, carbonic acid is formed by the first impact of the air upon the fuel; but in charcoal furnaces the acid is immediately reduced to oxide by taking the necessary amount of carbon into combination, and the gas reaches its highest reducing power even in the near vicinity of the tuyeres. Coke, being harder, does not produce so strong a reducing gas in that part of. the furnace. Carbonic acid is formed as in the case of charcoal, and remains longer before its reduction to oxide is completed. Anthracite is the

Jan 1, 1879

By L. G. Evans, C. Rampacek, G. A. Freeman

A large aggregate tonnage of oxidized and mixed oxide-sulfide copper ore of the southwestern U.S. is not amenable to conventional flotation concentration or sulfuric acid leach treatment. Most of the ores contain chrysocolla as the principal oxide copper mineral, for which no successful commercial flotation method has yet been developed. Acid leaching some ores is not feasible since they contain substantial quantities of calcite and other acid-consuming constituents. Other ores decrepitate during leaching or contain excessive slime and clay minerals which cause plugging of the ore beds.

Jan 10, 1961

By H. J. Wasson, E. B. Hopkins

Throughout 1928, production of oil from Venezuela steadily increased, and at the close of the year, the output was at the rate of nearly 400,000 bbl. a day. The total for the year was approximately 106,500,000 bbl., representing an increase of about 66 per cent. over the 63,000,000 bbl. produced in 1927. Venezuela now stands next to the United States as the second largest oil-producing country in the world; and there is abundant evidence to suggest that this relationship will endure for a number of years. Reserves were notably increased in the Lake shore fields, and the potential output of the Maracaibo Basin is much greater than the current production. In spite of this, the percentage of production increase was comparatively moderate, and the rate of this increase continued to fall off slightly, as has been the case for the last three years. This does not suggest that further annual increases in Venezuelan output will not materialize; only that the rate of these increases appears to be on the decline, and that with every succeeding year the future tendency will be in the direction of a stabilized level of output. The following table shows the production trend of the country since 1925: 1925 increase over 1924, 132 per cent. 1926 increase over 1925, 80 per cent. 1927 increase over 1926, 75 per cent. 1928 increase over 1927, 66 per cent. Many factors will work to prevent a reversal of this trend, but the principal ones are strong ownership in large-acreage units, and the probable indisposition of the world market to absorb a more rapidly increasing Venezuelan output at prices profitable to the producers. The distress oil element is not a factor in Venezuela; also, any unforeseen jump, such as results in the United States from the discovery of a Seminole or a deep sand at Long Beach, or Santa Fe Springs, is impossible in Venezuela, on account of lack of means for transporting a sudden surplus of oil, and the slowness with which additional transportation equipment in the form of shallow-draft tankers can be obtained.

Jan 1, 1929

By T. A. Rickard

The writing that is effective is woven with a fine texture into an agreeable pattern; it is free from knots, loose threads, and stray fluff. The instrument that weaves this literary fabric, whether it produce a homely sock or a lordly tapestry, a simple story or a learned 'Itreatise, is a disciplined intelligence, as sure as a steel needle, as precise as a swift loom. The simile breaks down at this point, for the product of the pen is instinct with the human spirit and therefore transcends in beauty anything made by a mere machine. If words are to be woven into eloquent meaning, they must be well knit. Upon the relation of words to each other and of groups of words to other groups, known as phrases, clauses, and sentences, depends the success of writing as a means of trans¬mitting thought from man' to man. To be understood beyond question, you should know not only what your words denote but how to build your sentences; you must not only choose your words aright but construct your sentences properly. A sentence is a combination of words that makes complete sense; it says something about something. ' A clause is a subordinate sentence or a sentence within a sentence. A phrase is a group of words without a predicate; it makes sense, but not complete sense. For example: I shall wait for a few minutes before I go home: The whole statement is a sentence; "I shall wait" and "before I go home" are clauses; "for a few minutes" is an adverbial phrase. The orderly arranging of words and of combinations of words is called `syntax'; and from the original Greek form, ouvaeis (suntaxis), is derived the Greek name for an editor,

Jan 1, 1931

Jan 1, 1944

Discussion of the papers of Benjamin Talbot. E. A. Beck, Emil Gathmann, Sir Robert A. Hadfield, and P. H. Dudley, presented at the New York Meeting, February, 1913, and printed in this Bulletin (No. 76, April, 1913). CHAIRMAN JAMES F. KEMP :-I call upon Prof. Albert Sauveur to open the general discussion on the subject of sound steel ingots. ALBERT SAUVEUR, Cambridge, Mass. :-I believe that I have the privilege, this instant, of opening one of the most important, significant and far-reaching discussions ever held before this Institute. I believe that our talk this morning will be heard far and wide, not only on this side of the water, but also on the other side. Everywhere, in short, where steel is manufactured. I welcome the opportunity of expressing my mind in regard to the production of sound steel ingots, a subject about which I entertain some very decided opinions. I shall not attempt to discuss the relative merits of the various processes that have been described. I shall, on the contrary, confine myself to a general consideration of the important questions before us. So intensely do I feel regarding the production of sound steel ingots that I have put my remarks on paper in my desire to present my Views.

Jan 4, 1913

By R. A. Fitch, J. D. Griffith

A performance calculation method was used in conjunction with experimental studies to develop means of predicting and interpreting miscible floods and to explore possible methods. of improving their efficiency. The calculation method is based upon the division of reservoirs into multiple independent zones or strata. Comparison was made with some experimental floods and with a field project to obtain some measure of the applicability of the method. Two aspects of miscible flooding were considered: (I) the displacement of a miscible front through a reservoir, and (2) the distribution and utilization of the solvent volume injected to maintain miscibility. Calculations and experihental observations indicate that alternate gas-water injection behind a miscible front significantly improves miscible flood performance, both within a single stratum and in a multistrata reservoir. Calculations were made on the extent to which miscibiliry is maintained by a given solvent volume in a stratified reservoir. Two alternate criteria for determining the optimum volume of solvent for injection are discussed. The preinjection of a small volume of water ahead of the solvent is suggested as a method of obtaining more efficient utilization of solvent. Calculations and experiments were made to investigate the effects of water preinjection. INTRODUCTION Miscible fluid displacement as a possible means of recovering oil has been the subject of extensive research and numerous field tests over the past several years. This work has brought out both favorable and unfavorable features of the miscible recovery methods. Many tests have shown that a miscible fluid can displace all of the oil contacted, leaving no high residual oil saturation, as is characteristic of immiscible displacements. The miscible methods have proven dificult to control, however, as evidenced by early breakthrough of the displacing fluid and poor sweep efficiency in several field projects. It became apparent early in the investigation of miscible displacement that the development of improved techniques and better methods of control would be required to extend the range of applicability to any significant portion of our petroleum reservoirs. The purpose of this study was to consider the problem of designing miscible floods to obtain better performance. A performance calculation was used in conjunction with experimental studies to develop means of predicting and interpreting miscible floods and to explore possible methods of improving their efficiency. Two aspects of miscible floods were considered separately in this study and the results are presented in two parts. The first part concerns the manner in which the miscible front is displaced through the reservoir. In these calculations the condition of miscibility between the reservoir oil and the displacing fluid is assumed. In the second portion the distribution and utilization of the preinjected solvent in maintaining rniscibility is considered. This portion dealing with solvent utilization applies only to the enriched gas or LPG slug processes. CALCULATION METHOD AND EXPERIMENTAL STUDIES COMPUTATIONAL MODEL The calculations for expected reservoir performance are based upon the multi-strata concept of reservoir properties. The method assumes multiple, independent strata (no crossflow between strata) and explicitly includes variations in patterns, injectivity, areal sweep and displacement efficiency. Lateral variation in permeability within the strata (for example, directional permeability) may be considered in the calculations, provided the variations are similar in all strata. The calculations based on this model furnish the rates of injection and rates of production of both oil and the displacing fluid for the composite system of strata. To carry out calculations on the mathematical model described, information is required on the performance of the displacement process under consideration in a single stratum element of the pattern to be used. In particular, for a given pattern and displacement process, data are required relating injectivity and composition of the produced stream to the volume of fluid injected. Data on the variations in areal sweep must also be available if it is desired to track the areal sweeps in the multi-strata model. These data may be obtained from experimental work such as model studies or other suitable methods. This representation of reservoir properties is, of course, an approximation and may be inappropriate in some cases. But the representation is not an arbitrary one since most oil reservoirs are essentially successive layers of sediment with the net producing pay zone often comprising but a fraction of the gross formation thickness. The fact that permeabilities measured in the vertical direction are frequently but a fraction of the horizontal permeability adds some evidence to the validity of this model. This type cal-

Jan 1, 1965

By B. C. Allen

Surface free energy and surface self-diffusion of solid molybdenum were studied in the temperature range 1600" to 2400°C using pressure-sintered bi-crystals. Comparison of groove angles formed in various surfaces perpendicular to the grain boundary indicate a maximum of 1 pct variation in surface free energy with crystallographic mientation. This anisotropy tends to decrease with increasing temperature. The surface diffusion of the bicrystals is equivalent to that of sheet with a mild (100) Preferred orientation. Anomalously low values found for bi-crystals with surface orientations of (OOl), (012), and (011) are rationalized in terms of anisotropy in surface free energy. THE effect of crystallographic orientation on surface free energy1,' and surface self-diffusion3,4 has been primarily studied in fcc metals. The object of this work was to study the effect of orientation on surface diffusion and surface free energy of bcc molybdenum using pressure-sintered bicrystals. EXPERIMENTAL WORK Materials and Crystal Preparation. Arc-melted molybdenum rod was obtained commercially and electron beam zone refined at 50 cm per hr at 10- 5 torr to form single crystals about 8 cm long and 0.65 cm diam. Three crystals were prepared with axial orientations about 1 deg from [001.], [011], and. [111]. To reduce the carbon content, the crystals were annealed 2 hr in 1.4 atm flowing wet hydrogen at 2050°C. Then the oxygen content was reduced by annealing for 2 hr in -30°C dewpoint hydrogen at 2020°C. The resulting impurity analysis is given in Table I. Bicrystal Preparation. The single crystal rods were cut into transverse slices with a thin silicon carbide abrasive wheel to produce specimens about 0.6 cm long. They were mounted in epoxy and surrounded by stainless steel washers. Cutting in half was done longitudinally at various angles to known crystallographic planes containing the cylinder axis according to Fig. 1. To reduce surface deformation resulting from the cutoff wheel and thus reduce parasitic grain boundary formation on subsequent annealing, about 0.003 cm was manually ground off each cut surface with 600 grit paper. Care was taken to keep the surface flat. After removal from the mounts, one half was generally ro-tated 180 deg with respect to the other to give a po- tential symmetrical tilt grain boundary between the two halves. In the other cases when low misorienta-tion angles were desired, the crystals were not rotated. On the basis of symmetry, sufficient bicrystals were prepared to cover the entire range of misorientations for symmetrical tilt boundaries. The misorientations, +, ranged from 0 to 45, 0 to 90, and 0 to 60 deg for [001], [011], and [111] bicrystals, respectively. One [Ill] twist bicrystal was prepared from 2 single crystal discs rotated 17 deg relative to each other. Each specimen consisted of two pieces which were placed in a cylindrical tantalum can. Sharp edges were rounded and the fit was made as snug as possible to reduce subsequent deformation during bonding. The assembly and crystals generally were vicuum outgassed at 900" or 1700°C and then electron beam welded in the can at l x 10-4 torr. After being leak checked, the samples were placed in an autoclave and hydrostatically gas-pressure bonded5 in four batches under helium at 10,000 to 18,000 psi at 1650°C for 3 hr. Satisfactory bonds were obtained in many cases, and most of the crystals bonded after two exposures. The results did not appear to be affected by the various pressures used, preannealing conditions, crystal orientation, or time-pressure-temperature route taken to the final bonding condition. After bonding, the tantalum cans were selectively removed in cold concentrated HF. Measurements indicated overall deformation was under 1 pct. The bicrystals were metallographically ground and polished flat and perpendicular to the axis. Examination showed the boundaries were straight and almost free of parasitic grains caused by extraneous local deformation. Annealing. In preparation for thermal grooving, the bicrystals were cleaned and annealed by outgassing at 10-5 torr at 1900°C and heating at 2300°C under 1 atm 99.996 Ar for 0.5 hr. The crystals were held in a closed 4-deck box made of molybdenum sheet, and were heated in a Ta-1OW resistance furnace. The ar-

Jan 1, 1970

By M. R. Geer Olds, H. F. Yancey

THE increase in the number of coal-cleaning plants employing dense-medium processes occurring since 1946 is especially interesting when viewed historically. Both sand and magnetite were introduced as material for heavy mediums at about the same time, sand in the Chance process in 1921 and magnetite in the Conklin process in 1922, but from that point on their records diverge. The Chance process enjoyed a steady growth from its inception, whereas no additional magnetite plants were built in the United States for over 20 years. Then, following the close of the World War 11, magnetite was again introduced, this time with marked success. During the following years some 47 plants employing magnetite medium were built. This rapid growth of dense-medium cleaning has been concurrent with widespread adoption of full-seam mining on one hand and a return to a more competitive market on the other. At a time when changing mining practice has provided cleaning plants with dirtier coal and changing market conditions have simultaneously demanded a cleaner product, the industry has through necessity turned to improved preparation. The inherently greater sharpness with which dense-medium processes can separate coal from impurity is thus helping to hold the line against ever-increasing mining costs and at the same time assisting materially in retaining badly needed markets. Although dense-medium cleaning unquestionably offers a distinct advantage when the washing problem is difficult, other methods can provide almost equally high efficiency when the coal is easy to wash. Moreover, fine coal cannot yet be treated by heavy medium in a proved process, although the Driessen cyclone is in the pilot-plant stage. Most of the present types of dense-medium equipment have been in use only a few years, and the dearth of information in the literature concerning their performance characteristics is entirely understandable, Nevertheless this information is necessary if the process is to be intelligently applied to individual cleaning problems. Without data on the efficiency of a process in a particular type of separation, it is difficult to assess the advantage to be expected from it. Similarly, the role of particle size in heavy-medium separation is important in some cases, yet there is little published information on this aspect. To mention only one more of the numerous points on which essential information is lacking, the bearing of medium characteristics on performance has been discussed only in qualitative terms. It was with the hope of providing information on some of these points that the Bureau of Mines built a dense-medium pilot plant for cleaning coal at its Northwest Experiment Station in Seattle in 1950. The plant has been operated continuously since that time, and over 50 runs have been made on 7 coals exhibiting a wide range of washability characteristics. An idea of the magnitude of this work will be gained from the fact that examination of the plant products has involved some 600 float-and-sink separations and about 2500 ash determinations. A laboratory pilot plant is especially well adapted to investigate many aspects of performance because close control over test conditions can be exercised and because a large number of tests can be made rapidly. On the other hand, factors such as consumption of medium and other cost items can be investigated satisfactorily only in a commercial plant. Actually, the two forms of investigation should be complementary, with the laboratory work pointing the way for confirming tests in commercial units. Pilot Plant The dense-medium pilot plant employed for this work comprises a 24x30-in. drum-type separating vessel, a 12-in. densifier, a 12-in. magnetic separator, a 26-in. x 9-ft vibrating screen, and the necessary pumps and conveyors for handling materials. Arrangement of these units corresponds with the flowsheet used in most commercial plants, except that a thickener is not provided for the feed to the magnetic separator. Coal and refuse discharge from the separating drum to the vibrator, which is divided longitudinally down the center. Medium draining through the first 3 ft of the screen is recirculated directly to the drum. Sprays on the middle 3 ft of the screen rinse medium from the products, and the last 3-ft section is for dewatering. Dilute medium from the rinsing and dewatering sections is pumped to the magnetic separator, where magnetic solids are recovered. These are pumped to the densifier, from which they return to the medium-drainage sump by gravity through a demagnetizing coil. The drum-type separating vessel is a scale model of a commercial unit. Feed enters axially at one end of the drum just below the surface of the bath, and float material overflows through a circular opening at the other end. Particles sinking to the bottom of the bath are picked up by lifting flights bolted to the inner wall of the drum, elevated out of the bath, and sluiced to the vibrating screen. Baffles suspended in the bath prevent float material from entering the sink-lifting flights. About 8 gpm of medium is used to sluice the feed into the drum. An additional 15 to 24 gpm, depending upon operating conditions, is added through two pipes dipping into the bath behind the baffle on the side where the sink-lifting flights enter the bath. The bath available for separation is 2 ft long and 13 in. wide, giving an area of 2.08 sq ft. Depth of bath from the surface to the top of the sink-lifting flights, measured vertically below the axis, is 6 in.

Jan 1, 1954

INTRODUCTION It has been impossible for the student, the practicing engineer, and the geologist to find all of the essential elements of mineral appraisal and mineral economic analysis in a single text. Indeed, the most recent texts on mine evaluation are over 20 years old. Many of the basic principles of mine sampling and evaluation have not changed over the ensuing years, but with the advent of the digital computer the entire scope of mineral evaluation has been expanded to encompass superior techniques that heretofore were not possible when using manual methods. The old manual methods for ore reserve computations and the techniques for assignment of area of influence to drill-hole samples are now as antiquated as the Model-T Ford. With the computer making possible solutions that had not been practicable in terms of time and effort, it is important for the practicing explorationist and mining engineer to understand many of the new concepts and principles that can be applied with the resolving power of the computer. Many practicing mineral industry professionals have been disappointed by certain computer programs and thus have some reservations about computers being able to solve their very real problems. Often the gap between the practicing engineer and the ivory tower theoretician applying modern computer techniques is too broad to be bridged with scattered, fragmented publications. PURPOSE AND SCOPE OF TEXT It is the intent of this book to update and to unify a great many scattered reference works used in the mineral industry today. The ensuing pages are addressed both to the professional already working in the mineral industry who needs information on computerized methods as well as to the serious student seeking to grasp the fundamentals and modern techniques of mineral appraisal and feasibility. These techniques are based on sound mathematical principles and theory, with the computer as a tool-but a very essential tool-for the solution of the problems involved. The computer can be of value only if it is programmed by those having sufficient expertise to use its inherent problem-solving capability, and the output is interpreted by those who are sufficiently acquainted with its operation to understand the data it produces. In the pages that follow the author intends to outline in considerable detail all the essen-

Jan 1, 1980

By AIME AIME

AT A meeting of the Boston Local Section of the Institute, on Oct. 3, approval was voted to the work done by its representatives on the Committee opposing the passage of a bill by the, Massachusetts Legislature to license engineers. The report is as follows: The Joint Committee on Licensing of Engineers, which included a Committee of the Boston Society of Civil Engineers and representatives of seven other societies,* submitted to the members of the respective societies, on Jan. 8, 1921, a report in which it was stated that on Jan. 4, 1921, a petition was filed in the Legislature of Massachusetts by the Boston Chapter of the American Association of Engineers accompanied by a bill to provide for the registration of professional engineers and land surveyors. This report also stated that at a meeting of this committee, held on Jan. 7, 1921, it was voted:

Jan 1, 1921

By E. T. Turkdogan, P. Grieveson

It is shown experimentally that, by making use of the coupled S-O reaction in ionic melts, it is possible to transfer slclJur or oxygen from a lozv to a high chemical potential through an ionic nzenzbrane. This uphill transfer of sulfur is accompanied by a counter downhill transfer of oxygen and vice versa. The Materials balance shows that the amoulits of sul -fur and oxygen lost or gained by one system are the same as those gained or lost by the other systenz — the two systejns being separated by an iofzic membmne. The systems used in these experi?nents were solid Mn-MnS-Mno and liquid Fe-S-0. Sufficient results were obtained Lo study the kinetics of the transfer and the indications are that the counter diffusion of sulfide and oxide iojzs in the membrane is the rate controlling process. WHEN an ionic oxide-melt reacts with an atmosphere containing sulfur and oxygen-bear ing gases the following reaction occurs: 1/2 S2 (gas) +O2- (melt) = S2- (melt) + 1/2 0, (gas) [1] Under the restrictions that i) electric conductance in the melt is purely ionic and ii) each constituent element in the melt does not change valence, the solution of an atom of sulfur in the melt will result in the evolution of an atom of oxygen, so that the electric neutrality is maintained. For a given temperature and melt composition, the equilibrium concentration of sulfur in the melt is determined by the ratio, po2 /ps2 , in the gas phase and not by the individual partial pressures of oxygen and sulfur. This has been demonstrated by a number of investigators, for example by Richardson and withers', Fincham and Richardson,la by St Pierre and Chipman,' and by Turkdogan and Darken.3 In his Howe Memorial Lecture for 1961, Darken discussed the possibility of uphill pumping of sulfur through an ionic membrane at the expense of oxygen. TO test the validity of this concept associated with coupled reactions, experiments were carried out in the following manner. A presintered mixture of Mn-MnS-MnO and prefused mixture of Fe-S-0, contained in platinum and iridium crucibles, respectively, and separated by a thin layer of soda-glass (to act as an ionic membrane), were placed side by side in an evacuated silica capsule and sealed. This was then kept at 1400°K for a required time to allow Reaction [11 to occur via the ionic membrane. When partial equilibrium is reached, the ratios Po2 /pS2, for systems on either side of the membrane, are equal and the flux of sulfur and oxygen through the membrane becomes zero, although the individual partial pressures po2 andp,, in these two systems may differ considerably.

Jan 1, 1962

Jan 1, 1924

By B. H. Sage, R. T. Carter, W. N. Lacey

The phase behavior of a number of binary systems consisting of parafin hydro-carbons has been determined in recent years. In addition, the composition of the coexisting phases of mixtures of crude oil and natural gas has been investigated.~ However, the latter study did not include information concerning the influence of the concentration of a component upon its distribution between two coexisting phases. Owing to the paucity of such information it was considered desirable to investigate in some detail the composition of the coexisting phases in the methane-propane-n-pentane system throughout the greater part of the two-phase region at a tempera-ture of 100°F. Information of this nature also permits the establishment of the critical behavior of this ternary system. Method The compositions of the coexisting phases in this ternary system at 100°F. were deter-mined by withdrawing samples from a pres-sure vessel containing a heterogeneous mixture of the three components that had been brought 10 equilibrium by mechanical agitation at the desired pressure and tem-perature. The samples were withdrawn under such conditions that the equilibrium was not disturbed and the composition of each of the phases was ascertained by means of the conventional low-temperature fractionation procedure. The apparatus employed in this investi-gation was nearly the same as that utilized in an earlier study of the methane-pentane system.~ Several minor modifica-tions in the arrangement of the apparatus were made in the interest of simplifying the procedure and avoiding the possibility of condensation in the tubing connecting the equilibrium apparatus with the analyti-cal equipment. The pressures were meas-ured by means of a pressure balance with a precision of 0.5 lb. per sq. in. It is believed that the equilibrium pressure was ascer-tained with an uncertainty of not more than 2 lb. per sq. in., even though small varia-tions in pressure obtained during the withdrawal of the samples. The tempera-ture of the equilibrium equipment was maintained by use of an automatically controlled oil bath. The bath temperature was determined by means of a copper-constantan thermocouple, the electromo-tive force being determined by means of a potentiometric circuit of such a nature as to reduce the uncertainty of the tempera ture to less than O.I f. The fractionating column employed in the determination of the composition of the gas phase had a diameter of 0.12 in. and was approximately 4 ft. long, while the column employed in the analysis of the liquid phase was 0.18 in. in diameter and about 5 ft. long. Each column was equipped with the conventional constant-volume receivers, which were maintained at a constant temperature by means of an automatically controlled oil bath. In nearly every case the distillation in thr neighborhood of the transition between

Jan 1, 1941

By W. N. Lacey, R. T. Carter, B. H. Sage

The phase behavior of a number of binary systems consisting of parafin hydro-carbons has been determined in recent years. In addition, the composition of the coexisting phases of mixtures of crude oil and natural gas has been investigated.~ However, the latter study did not include information concerning the influence of the concentration of a component upon its distribution between two coexisting phases. Owing to the paucity of such information it was considered desirable to investigate in some detail the composition of the coexisting phases in the methane-propane-n-pentane system throughout the greater part of the two-phase region at a tempera-ture of 100°F. Information of this nature also permits the establishment of the critical behavior of this ternary system. Method The compositions of the coexisting phases in this ternary system at 100°F. were deter-mined by withdrawing samples from a pres-sure vessel containing a heterogeneous mixture of the three components that had been brought 10 equilibrium by mechanical agitation at the desired pressure and tem-perature. The samples were withdrawn under such conditions that the equilibrium was not disturbed and the composition of each of the phases was ascertained by means of the conventional low-temperature fractionation procedure. The apparatus employed in this investi-gation was nearly the same as that utilized in an earlier study of the methane-pentane system.~ Several minor modifica-tions in the arrangement of the apparatus were made in the interest of simplifying the procedure and avoiding the possibility of condensation in the tubing connecting the equilibrium apparatus with the analyti-cal equipment. The pressures were meas-ured by means of a pressure balance with a precision of 0.5 lb. per sq. in. It is believed that the equilibrium pressure was ascer-tained with an uncertainty of not more than 2 lb. per sq. in., even though small varia-tions in pressure obtained during the withdrawal of the samples. The tempera-ture of the equilibrium equipment was maintained by use of an automatically controlled oil bath. The bath temperature was determined by means of a copper-constantan thermocouple, the electromo-tive force being determined by means of a potentiometric circuit of such a nature as to reduce the uncertainty of the tempera ture to less than O.I f. The fractionating column employed in the determination of the composition of the gas phase had a diameter of 0.12 in. and was approximately 4 ft. long, while the column employed in the analysis of the liquid phase was 0.18 in. in diameter and about 5 ft. long. Each column was equipped with the conventional constant-volume receivers, which were maintained at a constant temperature by means of an automatically controlled oil bath. In nearly every case the distillation in thr neighborhood of the transition between

Jan 1, 1941

By D. Watson, T. J. N. Grainger-Allan

A technique for studying the mechanism of the froth flotation process in which continuous froth removal does not take place but, instead, an equilibrium is reached between froth and pulp is described. A flotation cell, specially designed to facilitate equilibration, and froth and pulp sampling procedures are described. The main advantage of the technique is that the ability to measure the steady-state froth height allows froth-stability effects to be separated from pulp-process effects. In the flotation of hematite front quartz, linear relationships are found between airflow rate and froth height and between airflow rate and the ratio at equilibrium of mass of values in froth to mass of values in the pulp. A simple mechanistic interpretation of these results is given. It is suggested that froth-stability effects may play a more important role than hitherto allowed. In particular, the way in which concentration and size distribution of gangue particles may affect overall flotation rate is shown.

Jan 1, 1975