Search Documents

By A. G. Spillette, R. L. Nielsen

The purpose of this paper is to further the understanding of reservoir response to hot-water injection by desuribing a two-dimensional, mathematical model of the process. Key assumptions are that no gas phase is present, and that the injected fluid reaches thermal equilibrium instantaneously with the reservoir fluids and sand. The resulting system of three partial differential equations is solved simultaneously through the use of a "leap-frog" application of standard alternating direction implicit methods for the solution of the mass-balance equations and the method of characteristics for solution of the energy-balance equation. The utility of the mathematical model is demonstrated by comparing numerical and analytic temperature distributions for hot-water bank injection and by comparing calculated with observed field behavior. Additional calculations show that hot waterfioding can recover significantly more oil than cold waterflooding, and that a hot-water bank recovers, with less energy input, nearly as much oil us continuous injection. Introduction Consistent field success with hot fluid injection processes requires good reservoir description and a thorough understanding of recovery mechanisms. The latter is fostered by a combination of well designed experimental studies and physically sound mathematical modeling. The purpose of this paper is to further the understanding of reservoir response to hot-water injection by describing a two-dimensional mathematical technique, indicating its validity, and demonstrating its utility for studying the effects of reservoir and operating parameters. Published experimental studies of hot fluid injection processes are few." Even if extensive data were available, two considerations discourage exclusive reliance on laboratory or field work. First, because of the severity of scaling requirements," laboratory results must be interpreted with care. Second, because of the one-shot nature of field experiments — injectivity/productivity tests and pilot floods—results seldom are available over the desired range of operating conditions. These factors emphasize the need for devoting attention to mathematical modeling to complement laboratory and field work. Through the use of mathematical models, scaling uncertainties can be bridged and response can be predicted for unique combinations of reservoir and operating conditions. Numerous mathematical models developed during recent years enable us to calculate temperature distributions, thermal efficiency (or conversely, fraction of heat lost), and oil recovery behavior for hot fluid injection. Ramey" and Spillette' recently have provided reviews of these methods. Most models have concentrated on predicting temperature distributions and thermal efficiency; few have been directed at predicting oil recovery.'."1° Although these techniques are useful for estimating effects of reservoir parameters and operating conditions on process performance, results are limited by the assumptions made and by the methods of coupling independently solved fluid-flow and energy-balance equations. A computer-based method is presented for predicting total reservoir response to hot-water injection that obviates most simplifying assumptions. The model simulates fluid flow and heat transfer in two dimensions within a vertical cross-section spanning the oil sand and adjacent unproductive strata. Known numerical procedures are used to solve the governing partial differential equations. The mathematical model handles the effects of reservoir heterogeneity, gravity, capillarity, relative permeability and temperature-dependent fluid properties. In addition, a wide range of operating conditions can be modeled, including hot-water followed by cold-water injection. Mathematical Description of Hot-Water Injection Key assumptions in the mathematical model for hot-water injection are that (1) no gas phase is present and (2) the injected fluid reaches thermal equilibrium instantaneously with the reservoir fluids and sand. Relative permeability and capillary pressure are assumed independent of temperature. Darcy's law for multiphase fluid flow relates the velocities of the oil and water phases to the phase pressure gradients by the following relations:

Jan 1, 1969

By John Wulff, H. H. Uhlig

Since its first mention in the literature in the eighteenth century12 the phenomenon of passivity in metals has stimulated much speculation and attendant controversy as to its nature and cause. No one of the numerous theories so far proposed has been generally accepted. ‡ Faraday,' in 1836, associated the passivity of iron with a protective film over the surface of the metal, which materially prevents or slows down reaction with corrosive environments. His theory was that oxidizing acids like nitric acid form an unstable oxygen or oxide layer over the iron surface, which protects the underlying metal from further attack. This concept was simple yet plausible, and without alteration has frequently been assigned in present-day discussions as explanation of the passivity of many metals. With the advent in recent times of stainless steels, it is not surprising that this oxide film theory of passivity proposed by Faraday has been used to explain the phenomenal corrosion resistance of stainless steels and other passive alloys. The passive alloys, such as the chrome-iron alloys, are supposedly covered with a protective oxide film, which forms on exposure of the alloy to air, is extremely stable and self-healing, and accounts for the remarkable resistance of these alloys to corrosion. Within the past few years, several investigators, following the theory of film protection, have attempted to gauge the resistance of the supposed film on steels. Brennert8 and Donker and Dengg9 determined the potential at which a negative ion (e.g., C1-) moving in an electric field reacted with the metal anode, as detected by increased current flow or change in potential of the steel electrode in an electrolytic cell. The potential corresponding to reaction Brennert called the film break-through potential.

Jan 1, 1939

By John Wulff, H. H. Uhlig

Since its first mention in the literature in the eighteenth century12 the phenomenon of passivity in metals has stimulated much speculation and attendant controversy as to its nature and cause. No one of the numerous theories so far proposed has been generally accepted. ‡ Faraday,' in 1836, associated the passivity of iron with a protective film over the surface of the metal, which materially prevents or slows down reaction with corrosive environments. His theory was that oxidizing acids like nitric acid form an unstable oxygen or oxide layer over the iron surface, which protects the underlying metal from further attack. This concept was simple yet plausible, and without alteration has frequently been assigned in present-day discussions as explanation of the passivity of many metals. With the advent in recent times of stainless steels, it is not surprising that this oxide film theory of passivity proposed by Faraday has been used to explain the phenomenal corrosion resistance of stainless steels and other passive alloys. The passive alloys, such as the chrome-iron alloys, are supposedly covered with a protective oxide film, which forms on exposure of the alloy to air, is extremely stable and self-healing, and accounts for the remarkable resistance of these alloys to corrosion. Within the past few years, several investigators, following the theory of film protection, have attempted to gauge the resistance of the supposed film on steels. Brennert8 and Donker and Dengg9 determined the potential at which a negative ion (e.g., C1-) moving in an electric field reacted with the metal anode, as detected by increased current flow or change in potential of the steel electrode in an electrolytic cell. The potential corresponding to reaction Brennert called the film break-through potential.

Jan 1, 1939

By John A. Church

EARLY in the month of August, 1877, a miner in Gold Hill, Nevada, made the unlucky remark that, according to his observation, that month was usually quite free from accidents in the mines. Never was presage wider from the truth. When the month closed twelve mishaps had occurred, killing six and wounding nine persons, and for the rest of that year the Comstock mining communities were kept in a ferment by the frequent occurrence of appalling disasters. There was a real tidal wave of calamity sweeping over the mines, which has not been repeated since, and according to common report was never known before on the Comstock. I was much interested in studying the character of these misfortunes, which also aroused concerted action on the part of the miners, and I have collected a list of the accidents which took place from July, 1877, to May, 1879. The number in this period of twenty-two months

Jan 1, 1880

By John A. Church

Early in the month of Angust, 1877, a miner in Gold Hill, Nevada, made the unlucky remark that, according to his observation, that month was usually quite free from accidents in the mines. Never was presage wider from the truth. When the month closed twelve mishaps had occurred, killing six and wounding nine persons, and for the rest of that year the Comstock mining communities were kept in a ferment by the frequent occurrence of appalling disasters. There was a real tidal wave of calamity sweeping over the mines, which has not been repeated since, and according to cornmoll report was never known before on the Comstock. I was much interested in studying the character of these misfortunes, which also aroused concerted action on the part of the miners, and I have collected a list of the accidents which took place from July, 1877, to May, 1879. The number in this period of twenty-two mouths

Jan 1, 1880

By P. E. Baker

An experimental study of heat flow in steam flooding was carried out with steam displacing water in a plane-radial fluid-flow model. Temperature distributions in the model reservoir, overburden, and substratum were measured at frequent intervals during flooding by means of a fixed array of thermocouples. Heat losses to overburden and substratum and the division of heat between the steam and hot-water zones in the reservoir were calculated from the temperature data by performing numerical integrations over the appropriate volumes. Temperature profiles and heat distribution results are presented. Some results were (1) the fraction of injected heat that is lost to overburden and substratum, when expressed as a function of time, did not depend on injection rate; (2) a significant portion of the injected heat was contained in the hot-water zone ahead of and underlying the steam front in the reservoir. The division of heat between the steam and hot-water zones did depend on injection rate; and (3) considerable gravity override was observed. The experimental results are compared with those of several published theoretical studies of heat transfer in hot-fluid injection; approximate agreement on heat losses is found with some of the most idealized theories. A valid comparison cannot be made in regard to steam us hot-water zone; basic interpretation of the hot-water zone, in terms of a vertical steam front, is clouded by gravity override in the experiments. INTRODUCTION The experimental study reported here primarily concerns two problems of heat transfer in steam flooding that have economic and engineering importance. These are (1) the fraction of injected heat lost to the overburden and substratum, and (2) the division of the remaining heat between a zone containing steam and a zone of hot water at lower-than-boiling temperature. The volume of the steamed region, which has a direct effect on oil recovery, can be calculated readily from these results. Several valuable theoretical studies have been published on this problem, but no experimental tests of the theories have previously appeared. Tests were needed because the effects of the necessary simplifications in the theories could not be determined otherwise. The basic, untested theoretical problem is the effect of "decoupling" heat and mass transfer, and the resulting inability to include the effects of heat transfer and condensation on fluid flow. The theoretical problem solved so far has been a heat transfer problem in which fluid is present as a heat carrier and flows in a stipulated manner, either linear or plane-radial. The simplifications that have sometimes been made in regard to thermal conductivity by, for example, Marx and Langenheim,l Lauwerier2 and Thomas3 apparently do not have an important effect on heat loss calculations, although the results of the different methods disagree to a certain extent, as shown by Spillette4 and by Ramey.5 A recent paper by the author6 compared the results of experiments in hot-water flooding with several theoretical results and showed a rather poor agreement. It will be seen that the experimental heat loss results for steam flooding, however, show acceptable agreement. These comparisons are discussed in a later section. EXPERIMENTAL APPARATUS AND PROCEDURE The system studied was one in which a sand pack, initially water saturated and at a uniform temperature, was flooded with steam at a constant rate and temperature. The temperature distribution in the "reservoir" and adjacent "strata" was measured with an array of thermocouples, and heat losses were determined from these measurements. The sand pack contained no oil because the only concern of the experiments was heat flow, and it was important to have the flow pattern as simple

Jan 1, 1970

By T. L. Joseph

THE invention of the Bessemer converter process in 1856 added great impetus to the manufacture of steel and is one of the outstanding contributions to process metallurgy. Although the process of refining pig iron by passing air through the molten metal bears the name of Henry Bessemer, it should be mentioned in passing that William Kelley of Eddysville, Ky., worked on the process as early as 1847. Kelley was granted a patent on the process in 1857, inasmuch as he was able to prove priority in discovery.1 After considerable litigation in 1865 the respective interests of Kelley and Bessemer were combined. On Sept. 10, 1856, Robert Mushet of England obtained his first patent on the application of manganese to cast steel. Mushet anticipated trouble in purifying iron by passing currents of air through it. His patent specified that steel made in this way often contained flaws and was red short or cold short. Mushet understood the refining of pig iron into steel well enough to realize the difficulties likely to be encountered from oxidation of the iron. Mushet was not only an inventor but he was also an investigator. He understood the principle of selective oxidation which takes place in the converter process, arid he realized therefore that the remedy for over-oxidation was attainable if a suitable metal could be found at a reasonable cost and in sufficient quantities. His first experiments were made in small crucibles holding a few ounces of metal. Later his work was conducted on a larger scale and with complete success. Manganese had been used in making steel a quarter of a century before the converter

Jan 5, 1927

By J. Parke Channing

These days of great industrial and social problems in America produce many suggested solutions and great changes. The practical engineer and employer of labor views these problems differently from the labor leader or the social reformer, but as never before he is sincerely interested in solving them in a way that will be just to all. The inevitable tendency of the day is toward "industrial betterment," " safety," '(industrial education," " efficiency," and the many other things which have become so familiar to progressive employers. There is no longer any question that these things are worth while from both the human and economic standpoints. They "pay" in dollars and cents. The very center of final success in improving conditions and increasing the efficiency of workingmen must be the spirit of fairness and a knowledge on the part of the employer of how to deal sympathetically and intelligently with his employees. Every progressive employer knows how greatly he desires foremen, superintendents, managers and others who possess these qualities. On the other hand, we are all familiar with serious mistakes made by young graduates of engineering schools who have had no opportunity to develop these qualities, and who have no real appreciation of the worth of the workers. Indeed, one wonders whether much ill-feeling, labor difficulties, and many strikes could not be avoided if such men had the right attitude. Is there any way of remedying this condition? If this particular difficulty can be solved, if these young engineers, many of whom are our coming leaders of industry, can be given the right perspective and the right understanding of these other problems in addition to fair, sympathetic methods of handling men, many of our other problems will be solved—not at once, but gradually and permanently, as these men make good and become influential in paths of industrial righteousness and industrial peace. Many progressive employers of to-day have enlarged their own perspective and realize the great importance of enlarging the perspective of those who shall follow them. How can it be done? For seven years a movement has been making

Jan 1, 1915

By H. G. Moulton

THE INCREASING scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth

Jan 2, 1920

By Nicholas J. Grant, Oliver Preston

PUBLICATION of data by Irmann' indicating outstanding thermal stability and elevated-temperature strength properties in a sintered aluminum powder product (SAP) stimulated interest in the strengthening of metals by means of a highly dispersed oxide phase. This material was produced by compacting, sintering and extruding a fine flake aluminum powder, resulting in a dense product containing 10 to 16 volume pct alumina, which arises from the thin oxide film on the starting powder, highly dispersed in a matrix of pure aluminum. The method of producing SAP, and the stable high-temperature properties obtained from it, introduced the possibility of developing superior materials for high-temperature service by powder metallurgy methods. The composition of the materials of this type which are presently under consideration is predominantly metallic, containing from less than 1 pct up to about 20 volume pct of the oxide. As a result, other properties of these materials, such as electrical and thermal conductivity, thermal shock resistance, and to a certain extent ductility, notch sensitivity, machinability and hot working properties, are also predominantly metallic. These alloys do not constitute, therefore, a completely new class of materials as do the cermets, but rather present a new means of modifying the properties of a metallic matrix. In this sense, SAP type alloys are more closely analogous to the alloy aging systems. While the strength properties realized in the oxide-pure metal systems at the lower temperatures are substantially less than the best attainable in the aging systems, the thermal instabilities in the latter make them of less value for use at temperature much above their optimum aging temperatures, as indicated in Fig. 1. While the means of obtaining an oxide dispersion are more difficult and costly than conventional aging processes, in the light of the as yet limited understanding of such systems there is considerable promise of improved high temperature properties arising from the thermal stability of these structures. Since the development of SAP in 1946, its properties and the properties of a series of similarAl,O,-A1 products containing from about 1 to 20 pct aluminum oxide have been fairly extensively studied and reported.'- "articular attention has been given to

Jan 1, 1958

By Frank Clemes Smith

The study of the so-called refractory gold-ores of the Potsdam sandstone, ores which are probably of wider occurrence and of much greater economic importance in the Black Hills than is generally supposed, has led the writer to formulate in the present paper some of the results obtained in the course of a special examination of these particular ores, conducted at the State School of Mines at Rapid City, So. Dak. Various circumstances have interrupted the work, and it will easily be seen that relatively little has yet been accomplished; but it is hoped that this little may be of sufficient interest to justify a later supplement. Tellurium, discovered by Muller von Reichenstein in 1781, is generally classed as a very rare metal; it is further mentioned by one of our late writers as " of comparatively little importance," and as obtained from its ores by a " complicated process.'' Concerning its rarity, we have some trustworthy evidence below. Its commercial importance, particularly in connection with electrical appliances, has been passed upon by Mr. Edison ; * and it is certain that, in some metallurgical processes for the treatment of gold- and silver-ores, it may be saved as a byproduct at a relatively reasonable expense. The importance of tellurium as a mineralizing agent is emphasized by the remarks of one of our leading metallurgists,jwho, in his own practice and by a wide series of experiments, has found its occurrence to be much more general than has been supposed. Recently the same writer has discussed the occurrence of tellurides and oxidized tellurium compounds in the gold-ores of Cripple Creek, Colo., and in those of the Black

Jan 1, 1897

By Walter P. Jenney

An investigation, conducted by the author, was begun in September, 1889, by the United States Geological Survey, having for its object the study of the questions bearing upon the occurrence and manner of formation of the deposits of lead- and zinc-ores in Missouri and the adjoining States. The field-work was completed in December, 1891. During the first season the State Geological Survey of Missouri furnished an assistant, and in other ways co-operated in the research within the boundaries of that State. In order that the ore-deposits of the southwest might be compared with those of other sections of the Mississippi valley, an examination was made of the lead- and zinc-mining area of Wisconsin-Iowa, and of the argentiferous lead-mines of the region extending westward from Hot Springs, Arkansas, to Indian Territory. In the discussion of the general geology, and in comparisons between the ore-deposits of the Mississippi valley and those of the Rocky Mountains, the writer has drawn largely from his personal experience, having been engaged for many years in professional work as a geologist and mining engineer in that region. The Director of the U. S. Geological Survey and the Scate Geologist of Missouri have kindly consented to the publication of the present paper. While giving the more important economic results, an endeavor has been made to set forth the unity of plan which appears in the formation of the deposits of lead and zinc of the Mississippi basin, and to show their relation to the argentiferous ores of the Rocky Mountains—that the ores of gold, silver, and mercury, and also of copper, antimony, zinc, and lead, have a universal common origin, irrespective of the geological formations in which they occur.

Jan 1, 1894

By Ralph A. Sherman, J. M. Pilcher

BY surface treatment of coal is meant the application of a material, either solid or liquid, to the surface of pieces of coal. The purposes of surface treatment are varied. They may be to identify or "trade-mark" the coal, to modify the burning characteristics, the coking tendencies, or the behavior of the ash, to prevent the freezing of wet coal, or to control the dust. The control of dust is the usual purpose of surface treatment. TRADE-MARKING COAL The application of color to the surface of coal for the purpose of identification and registration of the trade-mark has been practiced to some extent. In 1928, the Glen Alden Coal Co. began to color its coal and adopted the trade-mark, "Blue Coal." The Old Ben Coal Co. later followed a similar practice with "Green Coal." A commoner means of identification of coal has been the stenciling of designs or pasting labels on large lumps or in the distribution of small cardboard tags through the smaller sizes. The details of the method used to color coal have not been revealed. Usually all of the coal is not treated, because of the expense. Only enough pieces are colored to show clearly when distributed through the coal.

Jan 1, 1943

By A. B. Kinzel

Precise knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly .ell known. General Method The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By A. B. Kinzel

Precise knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly .ell known. General Method The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By H. E. Lee, P. C. Feddersen, D. R. Gittinger, G. W. Dunn, J. B. Schuettenhelm

The new Bunker Hill slag-treatment plant, designed ior, a capacity of 300 to 400 tons of hot slag per day, was "blown in" April 5, 1943. In the ensuing I5-months period, 157,530 tons of slag was processed, with an average recovery of over go per cent of the zinc and practically all of the lead contained. In addition to this high metal recovery, utilization of the waste heat in the gas and fume venting, the process has enabled the generation of 231,376 tons of steam at 250-lb, gauge. Over the first six months opcration the volume of slag treated averaged somewhat under 300 tons per day. Reclaimed dump slag made up only about 1 5 per cent of the plant feed. In October 1943, preparations for the smelting of additional tonnages of dump slag were completed and the plant capacity was increased to an average of about 420 tons of slag per day. During the nine-months interval since that date, monthly averages of 450 toils per operating day have been maintained several times. The new plant (Fig. I) is constructed in close proximity to blast-furnace operations. The fuming furnace and other necessary equipment are housed in an eastward extension of the existing blast-furnace building. Beyond this housed extension the dust-laden gas is conveyed about the perimeter of a large rectangle formed by the flues, cooling towers and baghouses. The course of a 10-ft. balloon flue, which transports the fuming furnace gas, describes the west and south perimeters. This flue connects with a set of cooling towers located at the southeast comer. The flue and cooling-tower system serving the deleading kiln constitute the north side and the two baghouses, serving the kiln and furnace operations, -border the east side. From these baghouses the several discharge gas flows are come biped and conveyed in to the rectangle, being vented to atmosphere by means of a fan through a centrally located zoo-ft. brick stack. In general, the plant design and operation follow quite closely that dictated by experience gained in years of slag-fuming practice by the Anaconda Copper Mining Go., at East Helena, Mont., and the Consolidated Mining and Smelting Co. of Canada, Ltd., at Trail, B.C., and more recently by the International Smelting and Refining Co. at Toocle, Utah. : Fuming operations at the East Helena and the Tooele plants are more or less identical. Trail practice differs chiefly in the methods employed for the storage of the hot feed slag and in the methods utilized for the handling and cooling of the fuming furnace gas. The new Bunker Hill fuming plant closely follows Trail procedure in the treatment of the furnace discharge gas while East Hclcna methods have been adopted for the storage of feed slag.

Jan 1, 1944

By Zay Jeffries

TUNGSTEN has the highest melting point of all the known metals, namely 3350° C.; it is one of the hardest of the metals; it has the highest equiaxing or recrystallization temperature after strain hardening, of any pure metal known. It is particularly distinguished because, when composed of small equiaxed grains, it is extremely. brittle and fragile at room temperature, and when possessing a fibrous structure it maybe ductile and pliable at room temperature. The common ductile metals act in exactly the opposite manner in this respect. The present paper will include a brief note regarding the manufacture of wrought and. ductile tungsten. The metallography of wrought and ductile tungsten in the various stages of manufacture will be considered more or less in detail. The general relationships between the properties of tungsten and other metals will also be considered. A discussion will be given explaining why fibrous tungsten is ductile at room temperature, even though past experience with other metals would indicate that it should be brittle. Finally, a brief note regarding some new fundamental metallographic propositions relating to all metals will be given.

Jan 6, 1918

By R. F. Mehl, G. V. Smith

THE decomposition of austenite in steels, because of its immense practical importance, has been subjected to extensive study in recent years from the point of view of the mechanism of the process.1-3 Although much information has been acquired a number of questions, principally of theoretical interest, remain. One is that of the atomic-crystallographic mechanism by which each of the various reaction products forms. The isothermal reaction products of the eutectoid decomposition in plain carbon steels (to which this study is restricted) have conveniently been classified in three general groupings-pearlite, bainite, and martensite. Of these several products, pearlite and martensite have been studied extensively, but bainite has received only scant attention. As a result, the mechanism of the formation of pearlite and that of martensite are now fairly well understood while a great deal of uncertainty exists regarding bainite. PEARLITE Pearlite forms from austenite by the precipitation of alternate platelets of cementite and ferrite, which grow into the austenite matrix.2-5 The rate of reaction may be described in terms of a rate of nucleation and a rate of growth 2 3 Mehl and Smiths have attempted to determine the lattice relationships existing between the ferrite in pearlite and the parent austenite. Using a pole-figure method of analysis, it was found that a limited number of ferrite orientations resulted from the decomposition of a single grain of austenite; it was not possible,[ ]decide between two assumed ideal relationships, both of which appeared to account for the experimentally determined pole figure. It was definitely shown, however, that the relationship obtaining was quite different from that determined for the proeutectoid separation of ferrite.7 No attempt was made to determine the habit plane (matrix plane to which the precipitate lies parallel) of the pearlite lamellae. Belaiew8 earlier had stated that the number of directions assumed by the pearlite lamellae in a single grain of austenite was 12 (no details were given) and concluded wrongly, as Mehl and Smith' have pointed out, that the lamellae delineate the {210} planes of ferrite.* MARTENSITE It is known that martensite is a transitional constituent of body-centered tetrag-

Jan 1, 1942

By Franz Wever

ACCORDING to Tammann,1 the explanation of the effect of mechanical deformation in producing changes in the properties of metals is one of the most important problems of physical metallurgy, taking rank with the study of the constitution of alloy systems; and this problem has long attracted-the attention of practitioner and scientist alike. Its solution was not advanced materially until Tammann2 set up his translation hypothesis with its crystallographic basis, while other hypotheses, such as the amorphous metal hypothesis of Beilby3 and Rosenhain,4 have been shown by more intensive studies to be less and less satisfactory. The principles of the Tammann translation hypothesis have proved to be useful even up to today and in spite of all of the recent accumulation of experimental data, while the differences of opinion which have arisen relate to the extent to which the hypothesis accounts for the observed changes in properties and to what extent further assumptions are necessary. Stimulated by the proposals of Tammann, there soon developed a lively experimental activity which aimed at the elucidation of the structural or crystallographic changes produced by the mechanical deformation of metals. Parallel movements of crystal "blocks" along definite crystal slip planes had already been observed by lowing and Rosenhain5 in 1900, in metals which had been moderately deformed but without shedding light on the crystallographic nature of the processes accompanying more severe deformation. The solution of this important problem was not advanced until a much later date, or until the methods of X-ray crystal analysis had become available. Shortly after the discovery of the diffraction of X-ray by crystals, symmetrical diffraction effects were

Jan 1, 1931

By J. A. Church

I. Early Furnaces,......423 11. Experiments with the HIgh-Shaft FURnace,..... 426 III. ExperMents wIth the Wide FURnace,..429 IV. ExperEentS with Extreme BOSH,... 43.2 V. Survival of the 56 by 180 IN. Furnace,.434 VI. Recent ExpeEiments,.....436 VII. SUMMary,........438 I. Early Furnaces. Copper blast-furnace construction in America has long recognized a general standard in the rectangular water-jacketed shaft with separate forehearth. The details, however, and especially those relating to shaft dimensions, have had to meet a great variety of conditions, and show no uniformity whatever. Selecting a few of the present day Western plants, we find furnace lengths varying from 12.5 to 87 ft., widths at tuyere level from 42 to 84 in., and heights above tuyeres from 5 ft. 4 in. to 22 ft. 4 in.; and comparing present designs with those of the past, we meet contrasts no less striking. Unlike its transverse section, the length of a furnace has come to depend rather on the size of unit desired than on the requirements of smelting; and if the question of length be ignored, several of the various existing designs can be grouped together on the basis of a common transverse section. This section, having a width at tuyere level of 56 in. and a height above tuyeres of 18 ft., was developed at Great Falls, and the story of its development contains some interesting features. Ground was broken for the Great Falls works in the spring of 1891. About a year later, the concentrator was able to begin operation, followed within the next few months by the Brueckner, reverberatory, and converter departments, and in April, 1893, by the first blast fur-

Jan 1, 1914