Search Documents

By W. B. Coleman

Considerable discussion on the effect of iron and steel scrap in blastfurnace burdens was presented in the January, 1927, issue of Mining and Metallurgy. Therein the question is asked as to what causes the difference in physical properties of pig irons where the chemical analyses are practically the same. This point no doubt has been noticed by a number of furnace operators, but several years ago very little thought was given to it. The foundries purchased pig iron, had it analyzed and found it to be within their specification. The castings made from this iron at times would be satisfactory and at other times hardness and shrinkage would occur. Since the iron was chemically correct the foundries generally were at a loss as to what to do. They changed their method of melting in the cupola and in some cases this corrected the trouble. In some instances the foundry would continue eliminating a brand of iron until the castings produced were satisfactory. Through this process of elimination they would finally arrive at the conclusion that a certain brand of iron was causing the trouble. During the course of this elimination minor changes might have been made in the melting and in the end satisfactory castings were secured without discovering any definite reason for the trouble. Frequently the foundries blamed the manufacturer of the pig iron although the seat of the trouble was in their own method of melting. I have in mind one foundry in particular that was using three brands of pig iron for producing their castings and their losses were rather high. Three entirely new brands of iron were substituted in the charge and still the losses continued. Even after using six brands of pig iron the management felt that the pig iron was the cause. The difficulties encountered in the melting of iron in the cupola, over the past several years, reflect in a great many cases on the operation of the cupola. At different times certain brands of iron were unsuitable for producing a certain class of castings, but at the same time one could see no reason why the iron should be considered abnormal. Irons from furnaces where production and low cost are the main factors that are being used in foundries produce in most cases harder cast-

Jan 1, 1927

By Homer Turner

THE nature and comparative features of anthracite and bituminous coals have been discussed by the writer in two previous papers.1 Although this paper is offered as a further contribution to the subject, it seems desirable at the outset to repeat some of the descriptive matter of the early works in order to show the actual connection between various constituents of both coals and the new photomicrographs and other physical and chemical properties.

Jan 1, 1929

By George H. West, Ross Cummings, L. V. Steck, B. P. Little, Robert D. Pike

The drilling of constantly deeper oil wells has made it imperative that the manufacturer of casing be ever searching for new methods and new materials to meet the increased demands. One phase of this search constitutes the subject matter of the present paper. Starting from the original Drake well in 1859, the depth of wells has advanced by leaps and bounds, until today depths of 6000 to 8000 ft. are common. Conditions point to the necessity for drilling to greater depths, and it is not at all improbable that much of the future oil produc- tion will be from wells around 10,000 ft. deep. The trend to deeper wells is nicely illustrated by the curve in Fig. 1.l The points plotted are the maximum depths attained in the various pools which were at their peak for the years given. It may be of some interest to observe the change that has taken place in the tensile and collapsing stresses over the last 25 years. The pressure at the bottom of a 900-ft. hole, equivalent to the pressure caused by an equal column of water, is only 450 1b. per sq. in. The equivalent water pressure corresponding to the depth of the deepest hole today would be 4762 1b. per sq, inch.

Jan 1, 1930

By W. H. Adams

Shortly after becoming one of the van-guard of mine-developers in the State of Virginia, during the year 1883, I called the attention of the Institute to certain deposits of pyrites, which have been largely worked since. In all cases these deposits are covered with iron-ore (limonite), extending 40, 50 or 60 feet from surface to water-level. The several classes of brown iron-ores are found almost continuously along a prominent ridge of mineral-bearing slates, which can be traced from the James river northeasterly to the North Anna, the Rappahannock and the Potomac rivers, crossing the counties of Louisa, Spottsylvania and Stafford. Outcrops are plainly discoverable from end to end of this belt, also, in places, to the right and left of it, and at intervals there are evidences of workings, some of them for known purposes and others of unknown age and meaning. These old workings have an interest aside from the minerals they may contain or may have yielded. I have been engaged during the past five years in the collection of facts concerning them, which might determine definitely the site of those iron-furnaces, placed by tradition within reach of " the towne called Germanna," which were the first ever built in this State or on this continent. The events which led to the establishment of this important industry are sufficiently narrated in a paper written by Mr. R. A. Brock, Secretary of the Virginia Historical Society, and printed in the Proceedings of the National Museum, 1885, page 77, from which I quote the following : " To Virginia, the first of the English settlements in America, belongs the honor of inaugurating within her limits, as a colony, that most important industry, iron manufacture. "The London Company contemplated a variety of manufacturing enterprises from the very beginning of its authority; prominent among them was that of iron. In 1610 Sir Thomas Gates testified before the council of the Company at London, that in Virginia ' there were divers minerals, especially iron-oare,' lying upon the

Jan 1, 1892

By H. W. Weart, D. J. Mack

SINCE the first recognition of eutectic solidification as the simultaneous formation of 2 solids from one liquid,1 many complex structures thus produced have been observed. Despite many attempts to ascertain it, however, the detailed mechanism by which these structures develop remains obscure. In an attempt to clarify the origin of eutectic structures, the study described in this paper was undertaken. The broad objective of the study was to investigate the effect of different solidification conditions on the structure of single eutectic grains. It was expected that the eutectic structure would thereby be isolated for study, but preliminary experiments revealed another structure within each grain. When a literature surveye revealed only 1 previous mention of the subgrain structure,' it was decided to determine the origin of the structure and to study its response to various growth conditions. Before presenting the details of the investigation, it is apropos to distinguish carefully among the 3 structures produced during eutectic solidification. This is especially desirable in view of the apparent confusion existing in the literature concerning the structures in a eutectic specimen. The confusion is due largely to the existence of the subgrain structure noted above which is easily mistaken for the grain structure. In the following paragraphs, an effort is made to distinguish the 3 structures by briefly describing their origin during solidification, even though the results are thereby anticipated slightly. The 3 structures produced during eutectic solidification are the grain structure, the colony structure, and the eutectic structure, each one contained by the one preceding it. The grain structure is analogous to the polycrystalline structure of a metal or inle-phase alloy in that each grain grows from a single nucleus. A somewhat broader interpretation is needed here, however, because of the presence of 2 phases in each grain. Since in most eutec-tics particles of 1 phase are dispersed in a matrix of the other, a grain may be taken to be the region in which the matrix phase is monocrystalline.*

Jan 1, 1959

By P. D. Frost, H. A. Robinson, J. R. Doig, M. W. Mote

The mechanism of hardening in heat-treatable zirconium alloys was foUNd to be analogous to that for titanium alloys. Zirconium containing a relatively large addition of a ß -stabilizing element such as molybdenum or columbium can be hardened by the following transformation: Lean alloys, having insufficient alloy content to retain ß at room temperature are hardened by the following transformation: Application of these findings in Zr-Mo-Sn and Zr-Nb-Sn alloys produced strengths as high as 190,000 psi with reasonable ductility. PRIOR research on zirconium alloys has been concerned with development of greater strengths and creep resistance by solid-solution hardening or by dispersion hardening. Although solution and aging heat treatments had been applied earlier to zirconium alloys, quenching frequently produced low ductility. The possibility that the ß-to-w transformation, discovered earlier in titanium alloys,' might also occur in zirconium alloys and cause low ductility was considered, and, indeed, was found as predicted2 to be the case. In the earliest experiments, the heat-treatment response of titanium, too, was disappointing. However, by avoiding the formation of the embrittling w phase, it became practical to obtain room-temperature strengths higher than 180,000 psi, with elongation values of 10 pct.3 Based on the present concept of titanium heat treatment, the principal requirement for a heat-treatable zirconium alloy is that it contains a certain minimum amount of one or more ß -stabilizing elements. Only molybdenum, columbium, and tantalum, when present in sufficient amounts, are known to stabilize ß zirconium to room temperature during rapid cooling from the ß field. Tantalum was undesirable because of its high thermal-neutron cross section. Aluminum and tin are effective a stabilizers, but aluminum has been shown to seriously decrease the corrosion resistance of simple zirconium alloys in hot water. Therefore, for the present study, tin was used as the stabilizer addition. The alloys selected for this evaluation are presented in Table 1 along with their analyses and ß-transus temperatures. The analyses indicated that intended compositions were usually realized. EXPERIMENTAL PROCEDURES All of the alloys were melted from sponge zirconium and fabricated to sheet for heat treatment

Jan 1, 1960

By W. E. Gaby

INTRODUCTION SINCE the time of their discovery, the genesis of the ores at Mount Morgan, and the nature of the changes which have affected the surrounding rocks, have been the subject of investigation and speculation by geologists and mining engineers. Developments at this mine, for a long period the greatest gold producer of the world, show that with depth the orebody grades into copper, of which metal it now furnishes a large output, exceeding in value the gold. In earlier times, the purity of the gold and the first extremely heterogeneous character of the ore made it an interesting problem. Now, the probable depth of the copper enrichment, genesis, and true relations of the neighboring rocks furnish equally profitable material for investigation, and the present somewhat detailed description of these ores and rocks, from microscopic study, may prove of interest. The mine occupies a highly silicified portion of a belt of quartz-porphyry, which is believed to be the oldest rock of the region. This belt of quartz-porphyry and allied rocks runs north and south between two areas of a later intrusive granite, as shown on the geologic map,1 Fig. 1. Near the orebody the quartz-porphyry has been intruded by a dense basaltic mass called the "Old Basic." Cutting all three of these igneous masses are two sets of basaltic dikes, one running northwest-southeast, and the other, cross dikes, northeast-southwest. These dikes may be contemporaneous with, instead of later than, the ore. Their number has caused peculiar difficulties in extracting it, as the clay selvage of decomposed material affords no adhesion between dike and ore, causing great blocks to loosen and come down.

Jan 9, 1916

By C. Scala, F. Bernstein

General expressions are derived relating the streaming potential to the electrochemical potential of a permeable junction separating two electrolytic solutions. By the methods of irreversible thermodynamics, these potentials are related to the flux of mobile species arising from differences in pressure and chemical composition. The flux is conveniently expressed as a transference number, the equivalents of a mobile species transferred through the junction per faraday of electricity. At constant pressure, the flux equation gives the electrochemical potential across the permeable junction. The streaming potential across the junction is obtained by imposing the condition of constant chemical composition. The familiar expression for the borehole SP is shown to be a particular solution of the general flux equation. The derived exprersions were verified in experiments with seven shale samples. Both the theory and experimental data provide additional proof of the presence and magniturle of the streaming potential in shales. INTRODUCTION In the interpretation of electric logs, there has been much concern over the correction to be made to the recorded SP for an electrokinetic or streaming potential originating from the difference in pressure between the mud column and the formation. It was long recognized by M. R. J. Wyllie that such an electrokinetic potential source mas in the mud cake opposite permeable sands.' More recently, M. Gondouin and C. Scala2 showed an additional but opposing electrokinetic source of potential to be in shale beds. Their work was supported by the very extensive and excellent work of Hill and Anderson.3 n the present contribution, the general relationships between the electrochemical potential and the corresponding streaming or electrokinetic potential are examined and clarified. A notable advance towards understanding the relation between the various sources of electrical potential in a borehole has been the application of the now common methods of irreversible thermodynamics to describe the passage of ions and water through charged electrolyte junctions such as in shales.' The advantages of these methods are twofold. Unlike classical thermodynamics, they can be applied to non-equilibrium sys- tems, i.e., systems in which flow takes place, provided the flow processes have reached a steady state. They also permit conventional thermodynamic properties to be related to the steady-state dynamic properties. These methods arc used here specifically to derive expressions relating the potential behavior of shales in terms of ion and water transport. Experimental verification of the expression for the shale streaming potential is given which in turn offers theoretical support to the existence of a streaming potential in shales.' Importantly, the relative contribution of transport parameters to the SP is clarified. The theoretical treatment is essentially that of Lori-mer, Boterenbrood and Hermans3 ut has been extended to derive the general expression for the SP.

By H. A. Tobelmann

age Introduction ............................. 22 Crushing............................... 25 Leaching............................... 28 .Reduction.............................. 47 Electrolytic Deposition..............a.......... 51 Discard for Purification of Electrolyte.................. 60 Recovery of Copper from Discard Solution .............. 62 Resolution of Cement Copper...................... 64 Summary............................... 64 Appendix............................... 66 Discussion............................... 69 Introduction The location, mode of occurrence of ore, and preliminary tests leading to the development of the present leaching process and the building of the present plant on the property of the New Cornelia Copper Co. at Ajo, have been described in previous papers presented to the Institute and in the discussions thereof.l It is sufficient to say that these tests began early in July, 1912, and were continued to the close of January, 1916; that small tests at Douglas were followed by the construction of a 1-ton plant at the mine; and this was followed by the operation of a 40-ton plant for 11 mo. In all about 15,000 T. of ore were treated experiment-

Jan 1, 1919

By C. Stansfield Hitchen

THE introduction of the logarithmic sector method of quantitative spectrography by Scheibe and Neuhäusser in 1928, and the subsequent .modification and improvement of the method by Twyman and Simeon, would seem to have marked yet a further advance in quantitative spec-trum analysis and its industrial application, inasmuch as it offers a simple means of eliminating some of the uncertainties inherent in the older methods based upon mere visual comparison of line intensities. In their recent admirable review of the position and capabilities of industrial spectroscopy, Brownsdon and van Someren1 say: Ways and means of facilitating the comparison of line-intensities so as to give them numerical values are helpful, and of these a logarithmic sector rotating in front of the slit appears to he one of the most promising; . . . the success recently experienced by the author in using this method for the examination of steels and solutions of metallic salts prompted him ,to investigate its possible use in estimating the impurities commonly present in crude and refined tin. The results of this investigation are submitted in the present paper. Details of a number of spectrographic analyses of tin for various impurities have already been published. Thus, Schweitzer2 describes the spectrographic examination of tin for lead, bismuth and cadmium, and was able to distinguish between such atomic percentages as 0.01, 0.05, 0.10, 0.30, 0.60, 1.20, 3.00 and 10.00. Negresco3 investigated the bismuth content of tin over a range of from 0.0005 to 35 per cent. Meggers, Kiess and Stimson4 compare spectrographic and chemical analyses of tin metal for copper, lead, iron, zinc, silver, nickel and bismuth. They stress also the value of spectrum analysis in the examination of tin used for boiler plugs, where the requirements that only minute quantities of impurities shall be present render the chemical analysis both tedious and difficult.

Jan 1, 1933

CHARLES KIRCHHOFF, Chairman. ALBERT SAUVEUR, Vice-Chair-man. A. A. STEVENSON, Vice-Chair-man. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. John Birkinbine, J. Esrey Johnson, Jr., Felix A. Vogel, William H. Blauvelt, William Kelly, Leonard Waldo, James Gayley, Richard Moldenke, William R. Walker, Henry D. Hibbard, Joseph W. Richards, William R. Webster. Henry M. Howe, E. Gybbon Spilsbury, Frederick \V. Wood. Robert W. Hunt, A. A. Stevenson is appointed an additional Vice-Chairman of the Committee. He will serve as Acting Chairman during the absence abroad of Professor Sauveur.

Jan 7, 1913

Organization Place Date 1918 American Institute of Architects Washington, D. C. April American Iron and Steel Institute New York, N. Y. May American Institute of Chemical Engineers : Berlin, N. H. June 19-22 American Society for Testing Materials Atlantic City, N. J. June 25-28 New York Electrical Society New York, N. Y. June National Association of Stationary Engineers Cincinnati, 0. Sept. 9-13 National Exposition of Chemical Industries New York, N. Y. Sept. 23-28 American Chemical Society Cleveland, 0. Sept. National Petroleum Association Atlantic City, N.. J. Sept.

Jan 4, 1918

By Chas. Y. Clayton, Francis B. Foley, W. E. Remmers

DuRing the summer of 1919, the late Dr. Henry M. Howe, then Chairman of the Division of Engineering of the National Research Council, organized a committee to obtain a better insight into the behavior of carbon steels under the influence of various treatments by a proper control of the time and temperature factors. During part of 1919 and 1920, work in connection with this investigation was carried on at Dr. Howe's laboratory at Bedford Hills, N. Y. During 1921 there was an enforced hiatus in the work, occasioned by the illness which resulted in Dr. Howe's death in 1922. At that time one of the present authors compiled the results of the work which had been done and this was published in 1923.' Following the publication of this work, it seemed desirable to carry on in the same manner an investigation of steel of C 0.75 per cent., which steel had not been as fully treated as had the other steels of C 0.34 and 0.52 per cent., used in the published work. Furthermore, certain unusual results have been obtained in the treatment of C 0.52 per cent. steel by quenching and drawing, and repetition of this part of the work seemed advisable. This has been done during the past year at the School of Mines and Metallurgy of the University of Missouri at Rolla, Mo., by a cooperative undertaking of the School and the Bureau of Mines, working in conjunction with the Committee on Heat Treatment of Carbon Steels of the National Research Council. The present paper is a report of the results obtained in this work.

Jan 1, 1926

By Charles B. Dudley

DEAR SIR: It is now nearly three years since my first report to you on the subject of steel rails was written. That report, as you will remember, dealt principally with the question of the relation between the chemical composition and physical properties of steel rails end their power to resist crushing and fracture in actual service. Other matters were referred to or touched upon in that report, but the main question was, Why do some rails crush or break in service while others do not? Yon will doubtless remember that the principal conclusion arrived at was, that the softer rails are less liable to Crush or break in service than the hard ones. Or, in other words, so far as conclusions could be drawn from the chemical analysis and physical test of 25 samples of steel rails which had actually been in service, these conclusions were that those rails which have the smaller amounts of carbon, phosphorus, silicon, and manganese are less liable to crush or break in service than those which have larger amounts of these elements. Or, again, looked at in the light

Jan 1, 1881

By W. E. Ruder

IT has been pointed out by Stead 1 that grains of considerable coarseness may be developed in steels containing from 3 to 5 per cent. of silicon, and in a previous paper 2 the present author has shown that under the proper conditions of annealing single grains having an area of 50 sq. cm. may be obtained. It is the purpose of this paper to discuss in more detail the conditions, promoting the growth of these grains, in the hope that the experiments described may throw some additional light upon the general problem of grain growth in metals. These silicon steels lend themselves particularly well to such experiments because of the ease with which the change in structure may be followed and because of the fact that the effect of the carbon present is largely obliterated by the high percentage of silicon. This forms a solid solution with the iron, which acts very much like a pure metal. This alloy has been found to have but one critical point, viz., Are. This point, determined by Roberts-Austen for Hadfield's 4 per cent. Si alloy, was found to lie at 703° C. Vigouroux3, in working with pure Fe-Si alloys, finds this point to rise from 750° C. for 0.5 per cent. Si to 860° for 6 per cent alloy, with a flat region in the curve from 3 to 4 per cent. Si. No accurate determination of this point has been undertaken by the present author, but it has been roughly determined to lie between 730° and 750°.

Jan 12, 1913

By A. N. Winchell

Petrographic studies of over 1400 rock and mineral samples, and studies of their field relations, show that there is a complete gradation between sandstone and limestone; the lime-silicate rocks were produced by recrystallization of limestone; mineralization and silicification occurred after silication and at considerably lower temperature; carbonation occurred at still lower temperatures. IN CONNECTION with law suits between mining companies at Bingham, Utah, a few years ago, the writer made petrographic studies of more than 1400 rock and mineral samples in thin sections, and also careful studies of their field relations. In petrographic studies, even when an area is studied intensively, attention is commonly centered very largely on the unusual features of special interest, so that the relative abundance of rock types (or minerals or textures) can only be determined by a study of map areas outlined largely by field methods, and cannot be based directly on microscopic work. It is very uncommon, and usually impossible, to take samples at regular short intervals along and across formations. It is precisely because such methods were used at Bingham that the work presents a rare opportunity for determining, on a microscopic basis, the relative abundance of rock types and the continuity of gradations between rock types. At the same time, a study was made of the alteration of sediments under the influence of igneous intrusions, with results that are believed to be of interest and importance.

Jan 3, 1924

By Erhard Hornbogen

Twins were propagated into large, well-annealed crystals of a, iron-phosphorous and a, iron-molybdenum solid solutions. Strain fields caused by interaction of these twins were made visible by precipitation. These strain fields can be explained by assuming that transmitted and reflected plastic waves are created when a twin strikes an obstacle with high velocity. The twin front itself can be regarded as a shear wave that may be able to develop a one-dimensional shock front. The occurrence of {WO} fracture by the reflected stress is also discussed. The described effects were not found when twins propagated at lout velocity into disturbed crystals, for example, into crystals previously deformed by slip. DEFORMATION twinning leads to shearing of a crystal lattice under external load. The shear appears to be homogeneous over a large number of crystal layers. In a iron, shear occurs on the (112) planes and in the <1ll> directions. The formation of a twin proceeds by the movement of partial dislocations that change the stacking at the twinning plane.l, In the bcc lattice, this partial dislocation can be created by dissociation of a sessile a/2[111] dislocation that lies in the (112) plane: Cottrell and Bilby&apos;s spiral mechanism can explain the homogeneous shear, but has not been proven experimentally. Nevertheless, this mechanism can explain the possible high velocity of formation of a twin. In Cottrell and Bilby&apos;s model, as in other models of twinning or phase transformation, a much higher energy is required to spread the first stacking fault than to add new layers by further movement of the partial dislocations. The dislocations will therefore become accelerated proportional to the difference between the stress, tN, to nucleate and tp to propagate the twin. It has been assumed3,4 that tn is the stress required to make two partial dislocations of apposite sign pass for the first time. After the first layer of new stacking has been formed, the maximum stress is TN=Gb/4pd where G is the shear modulus, b is the Burgers vector of the partial dislocation, and d is their perpendicular spacing so that the amount of shear is S = b/d. From this formula, a value of 25 kg per mm2 has been estimated for twinning in Zn3. The measured values are smaller, but local internal stresses may help to provide the necessary stress. For a iron, a higher value can be expected, mainly due to the higher value of G. That agrees with the observation that "burst" twinning occurs if the yield strength is in-

Jan 1, 1962

A1 in carbon steel, equilibrium temperature, XLVII, 740-747. A2 and A3 in pure iron, critical ranges, XLVII, 665-739. Abbott, Ai Arthur: [biog. notice, Bulletin No. 27, Mar., 1909, xxvii]; death, XXXIX, . [xl]. Abbott, Arthur Vaughan: [biog. notice, Bulletin No. 16, July, 1907, 6581; death, XXXVII, [xxxix]. [ ]

Jan 1, 1918

By M. L. Samuels

DURING the period from 1910 to 1920, there was a lively interest in the subject of grain growth and many papers were published, followed by interesting discussions. Questions dealing with the fundamentals of grain growth-why and how it occurs-were treated in papers by Howe,1 Jeffries,2 Sauveur,3 Chappell,4 Beilby,5 Mathewson and Phillips,6 McAdam,7 Carpenter and Elam,8 Stead and Carpenter,9 Ruder,10 as well as others. Since that decade, much indeed has been done regarding the practical control of grain size, and it is now possible to order material having a size specified in the American Society for Testing Materials classification. Also, one hears the term "spliced boundaries" used in connection with certain tungsten lamp filaments" wherein it is important to prevent "sagging" between consecutive turns of the helix." This practical use of a certain knowledge as to the things that influence or even control grain growth should not be taken as an indication that the subject has been thoroughly explored and that nothing more can be learned from fundamental studies. It is with this thought in mind that a report of some observations and experiments on abnormal grain growth is believed justified. Abnormal grain growth is met with in heat-treating high-carbon steels in the austenitic range,13 in the hardening treatments of high-speed steels, 14.11 and in the low-temperature annealing of strained low-carbon steels as in sheet and wire material. Entirely aside from these instances of exaggerated grain growth, which some might consider as freakish, it is thought that abnormal growth is simply a case where the growth forces and the forces tending to prevent growth are almost, but not quite, evenly balanced. Information relative to grain-growth characteristics in general may be obtained from a study of abnormal growth conditions, which may be looked upon as vantage points. Reflection will show at once that if growth forces are great in comparison to inertia or resistance to growth, many crystals start to grow and, for that reason, none becomes very large, whereas if inertia is predominant no growth at all takes place. Under conditions in which

Jan 1, 1938

By J. J. Crowe, G. K. Burgess

PAGE, Theories of Allotropy of Iron........... 667 Previous Determinations of A2 and A3 in Iron........ 668 Critical Ranges as Determined by Expansion........ 669 Critical Ranges by Thermoelectric Observations........ Critical Ranges in Terms of Crystalline Structure....... 670 Critical Ranges as Detected by Mechanical Methods...... 670 Critical Ranges as Given by Electrical Resistance....... 670 Critical Ranges as Determined Magnetically........ 671 Critical Ranges as Determined Calorimetrically....... 673 Critical Ranges from Heating and Cooling Curves....... 673 Summary of Previous Determinations of A3 and A2 in Pure Iron.... 675 The Present Investigation............ 678 The Experimental Method........... 678 Arrangement of the Apparatus.......... 679 The Measurements of Temperaturc.......... 679 The Measurement of Time........... 679 The Thermocouples............ 681 Temperature Scale and Calibration of Thermocouples...... 681 Mounting of Thermocouples........... 682 The Differential Measurements.......... 682 The Furnace and Accessories........... 682 The Vacuum Pump............ 683 The Energy Supply............683 The Rheostat.............. 683 The Materials Investigated............ 685 Sources of Iron............. 685 Preparation and Description of Samples......... 685 Chemical Analyses............. 687 The Experimental Data............. 688 The Preliminary Observations.......... 688 The Definite Series............691 Description of the Plotted Curves........... 694 The Effect of Plotting at Different Intervals........ 694 The Curves of the Definite Series.......... 695 . The Curves of the Preliminary Series......... The Existence of Other Critical Ranges......... 696 The Microscopical Examination........... 697 Summary and Conclusions............ 698 Bibliography............... 701 Plates................ 704

Jan 1, 1914