Search Documents

By H. W. McQuaid

IT IS usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effect of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide can result in total unfitness of low-carbon steel for, case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 2, 1922

By I. C. White, G. H. Ashley, J. A. Bownocker

Among the rich mineral deposits of the great Appalachian field, the Pittsburgh coal bed stands pre-eminent. Other coal beds may cover a wider area, or extend with greater persistence, but none surpasses the Pittsburgh seam in economic importance and value. It was well named by Rogers, and his able assistants of the First Geological Survey of Pennsylvania, in honor of the city to whose industrial growth and supremacy it has contributed so much. Whether or not the prophetic eye of that able geologist ever comprehended fully the part which this coal bed was to play in the future history of the city that gave it a name we do not know; but certain it is that the 7 ft. of fossil fuel, which, in Rogers' time, circled in a long black band around the hills and, overlooking the site of Pittsburgh from an elevation of 400 ft. above the water of the Allegheny and Monongahela, extended up the latter stream in an unbroken sheet for a distance of 200 miles, has been the most potent factor in that wonderful modern growth that has made the Pittsburgh district the manufacturing center of America, and that bids fair to continue until it shall surpass every other district in the world, even if it does not now hold such primacy.' The Pittsburgh coal bed stands today as probably the largest contributor of wealth of any single mineral deposit in the world. If it is not, what other deposit is? It has contributed to Pennsylvania alone more than 2,500,000,000 tons of high-grade coal worth nearly $4,000,000,000; since 1910, it has added more than $2,500,000,000 to the value of Pennsylvania's mineral output. In 1920, this bed2 contributed 127,227,000 tons of coal as follows: Pennsylvania, Pittsburgh district........................ 38,245,000 Connellsville district................................. 34,095,000 Weatmoreland-Ligonier district........................ 16,107,000 88,447,000 West Virginia, Fairmont district........................ 15,571,000 West Virginia-Ohio, Panhandle No. 8 district............. 21,128,000 Maryland-Potomac (Est. one-third of production)......... 2,081,000 38,780,000 Total........................................... 127,227,000

Jan 1, 1927

By H. E. Wheeler

The work described was carried out during 1917 and 1918 at the testing laboratory of Watertown Arsenal at the instigation of the Nitrate Division and later with the concurrence of the Cannon Section of the Ordnance Department, U. 8. A. The experiments follow three principal lines of work: First, the effect of nitrogen under pressure on steel containers of various compositions at a red heat; second, the effect of decomposing ammonia on various alloy steels, iron, and non-ferrous alloys; third, a new theory of the erosion of guns in respect to the effect of nitrogen in steel. Part I In the Haber process for the manufacture of ammonia from its elcnlents, it is necessary to have nitrogen and hydrogen of 1500 lb. per sq. in. (105.5 kg. per sq. cm.) at a temperature of 500 to 600' C. The steel containers for these gases gave trouble by failing without apparent cause. When the General Chemical Co. began to develop its method for the production of ammonia, it experienced the same difficulty and, knowing that the Haber process had solved the difficulty by the use of alloy steels, it made several small steel bottles of different compositions and kept them filled with these gases at this pressure and temperature until they failed. The time of service varied from a few days, for the plain steel casting, to two years for a chrome-vanadium forging. Four of these steel bottles were sent to this laboratory for investigation; they were a plain carbon-steel forging, a nickel-stee1 forging, a chrome-vanadium steel forging, and a chrome-steel forging. The time of service was as follows: plain carbon steel, 4 mo.; nickel steel, 6 mo.; chrome-vanadium steel, over 2 yr.; chrome steel, 4 mo. When these containers were cut open and the cross-section surface polished, they showed an inside zone with a different luster from the rest of the metal. Upon etching, this zone was almost unaffected while the rest of the steel etched normally.

Jan 1, 1922

By H. E. Wheeler

The work described was carried out during 1917 and 1918 at the testing laboratory of Watertown Arsenal at the instigation of the Nitrate Division and later with the concurrence of the Cannon Section of the Ordnance Department, U. 8. A. The experiments follow three principal lines of work: First, the effect of nitrogen under pressure on steel containers of various compositions at a red heat; second, the effect of decomposing ammonia on various alloy steels, iron, and non-ferrous alloys; third, a new theory of the erosion of guns in respect to the effect of nitrogen in steel. Part I In the Haber process for the manufacture of ammonia from its elcnlents, it is necessary to have nitrogen and hydrogen of 1500 lb. per sq. in. (105.5 kg. per sq. cm.) at a temperature of 500 to 600' C. The steel containers for these gases gave trouble by failing without apparent cause. When the General Chemical Co. began to develop its method for the production of ammonia, it experienced the same difficulty and, knowing that the Haber process had solved the difficulty by the use of alloy steels, it made several small steel bottles of different compositions and kept them filled with these gases at this pressure and temperature until they failed. The time of service varied from a few days, for the plain steel casting, to two years for a chrome-vanadium forging. Four of these steel bottles were sent to this laboratory for investigation; they were a plain carbon-steel forging, a nickel-stee1 forging, a chrome-vanadium steel forging, and a chrome-steel forging. The time of service was as follows: plain carbon steel, 4 mo.; nickel steel, 6 mo.; chrome-vanadium steel, over 2 yr.; chrome steel, 4 mo. When these containers were cut open and the cross-section surface polished, they showed an inside zone with a different luster from the rest of the metal. Upon etching, this zone was almost unaffected while the rest of the steel etched normally.

Jan 1, 1922

By Warren B. Weeks

The year 1940 saw an increase of 20 per cent in oil production over the previous year—compared with a 16 per cent increase the previous year. In all, 25,790,380 bbl. were produced, an increase of 4,414,150 bbl, over 1939 and the largest production figure for south Arkansas since 1928. The older settled production continued to decline. Magnolia accounted for most of the increase, with aid from the other recent deep fields. During the year, 169 wells were drilled, 79 fewer than in the previous year. Of 131 wells drilled in proven fields, 18 were dry. Three of the 38 wildcats were pool openers. The drilling depth record was increased from 9028 to 9550 feet. Trend of Prospecting For the first time since 1936, the search for oil in the deep Smackover limestone slackened perceptibly; g dry wildcats ended in Smackover, 2 in. the underlying Eagle Mills; 7 penetrated Paleozoic beds, while 9 ended in Hosston, 2 in Glen Rose, 2 in Paluxy and 4 in Gulf. Geology The wells listed in Table 2 either resulted in the discovery of new oil pools or, because of their depth or location, afforded impor-tant stratigraphic or structural informa-tion. Fig. I is a general columnar and stratigraphic section showing the relation-ship of the strata within the Comanche series. The nomenclature shown was ac-cepted by the Shreveport Geological Society. It was subsequently published by Imlay,l who indicated probable correlations with other areas and presented evidence for the possible Jurassic age of the under-lying Cotton Valley and Smackover formations. New Fields Pouke.—On June 10, 1940, the Louark Producing Co. completed its No. I Sturgis, sec. I, T. 17 S., R. 27 W., in central Miller County, producing between 3583 and 3607 ft. in the upper part of the Paluxy forma-tion. The well flowed I00 bbl. of 3r.4' gravity oil per day through Ns-in. tubing choke. This discovery resulted from seismograph work. Six other wells were drilled in the area, none of which found production in the original sand. One of these wells is producing from a sand 50 ft. deeper in the section. The others were abandoned. No further development is in prospect. Production is from lenticular sands of the upper Paluxy; 45,556 bbl. had been pro-duced by the end of 1940. There is structural closure against a fault to the northwest. McKanzie.—The Atlantic Refining Com-pany's No. I Bodcaw Lumber Co., sec. 29, T. 17 S., R. 23 W., eastern central La-fayette County, was completed June 8, 1940, as the eighth and farthest west of the Smackover (Reynolds o6lite) limestone pools. The well flowed 10 bbl. an hour of 58.6' gravity distillate through an 1 1/64 Ma-in. tubing choke, with a gas-oil ratio of 8400:I.

Jan 1, 1941

By Warren B. Weeks

The year 1940 saw an increase of 20 per cent in oil production over the previous year—compared with a 16 per cent increase the previous year. In all, 25,790,380 bbl. were produced, an increase of 4,414,150 bbl, over 1939 and the largest production figure for south Arkansas since 1928. The older settled production continued to decline. Magnolia accounted for most of the increase, with aid from the other recent deep fields. During the year, 169 wells were drilled, 79 fewer than in the previous year. Of 131 wells drilled in proven fields, 18 were dry. Three of the 38 wildcats were pool openers. The drilling depth record was increased from 9028 to 9550 feet. Trend of Prospecting For the first time since 1936, the search for oil in the deep Smackover limestone slackened perceptibly; g dry wildcats ended in Smackover, 2 in. the underlying Eagle Mills; 7 penetrated Paleozoic beds, while 9 ended in Hosston, 2 in Glen Rose, 2 in Paluxy and 4 in Gulf. Geology The wells listed in Table 2 either resulted in the discovery of new oil pools or, because of their depth or location, afforded impor-tant stratigraphic or structural informa-tion. Fig. I is a general columnar and stratigraphic section showing the relation-ship of the strata within the Comanche series. The nomenclature shown was ac-cepted by the Shreveport Geological Society. It was subsequently published by Imlay,l who indicated probable correlations with other areas and presented evidence for the possible Jurassic age of the under-lying Cotton Valley and Smackover formations. New Fields Pouke.—On June 10, 1940, the Louark Producing Co. completed its No. I Sturgis, sec. I, T. 17 S., R. 27 W., in central Miller County, producing between 3583 and 3607 ft. in the upper part of the Paluxy forma-tion. The well flowed I00 bbl. of 3r.4' gravity oil per day through Ns-in. tubing choke. This discovery resulted from seismograph work. Six other wells were drilled in the area, none of which found production in the original sand. One of these wells is producing from a sand 50 ft. deeper in the section. The others were abandoned. No further development is in prospect. Production is from lenticular sands of the upper Paluxy; 45,556 bbl. had been pro-duced by the end of 1940. There is structural closure against a fault to the northwest. McKanzie.—The Atlantic Refining Com-pany's No. I Bodcaw Lumber Co., sec. 29, T. 17 S., R. 23 W., eastern central La-fayette County, was completed June 8, 1940, as the eighth and farthest west of the Smackover (Reynolds o6lite) limestone pools. The well flowed 10 bbl. an hour of 58.6' gravity distillate through an 1 1/64 Ma-in. tubing choke, with a gas-oil ratio of 8400:I.

Jan 1, 1941

By C. S. Barrett, C. T. Haller

TWINNING in magnesium is known to occur profusely under certain conditions, and when it occurs in polycrystalline materials it brings about a partial or even a complete change in the preferred orientation. The amount of research on this subject, however, has not been in proportion to its importance as a mechanism of deformation and reorientation. Much of the research has been limited to twinning in single crystals. The present study' concerns polycrystalline sheet, and is an investigation of the twinning produced by plastic deformation as a function of the following variables: I. Direction and type of deformation. 2. Amount of deformation. 3. Speed of deformation. 4. Temperature of deformation. 5. Composition and temper of the sheet. 6. Twins previously produced. 7. Twins previously produced, then annealed. By proper control of these variables it is shown that, on a laboratory scale, samples can be produced that are free from preferred orientations. MATERIALS AND METHODS The materials used were samples of commercial magnesium-alloy sheets with nominal compositions given in Table I. [ ] X-ray diffraction was used in most of this work to detect the twins and to estimate the amount of twinning. Since twinning on {102} planes causes a reorientation of the crystal lattice by 86°, it is very easy to study with X-ray diffraction patterns, particularly if one notices the diffraction ring from the basal plane the 002 reflection. By properly directing the X-ray beam, it is possible to produce 002 reflections from twinned material at, say, the 6 and 12 o'clock positions on the 002 ring, with the untwinned material reflecting to 3 and 9 o'clock positions; and by judging the relative intensity of the arcs on the diffraction ring at these positions, it is possible to judge the amount of twinned material relative to the untwinned. This X-ray method of estimating the amount of twinning is generally superior to metallographic observation, for it was found

Jan 1, 1946

By Thomas E. Leontis

INTRODUCTION THE importance of magnesium alloys in the manufacture of aircraft engines has been realized for many years. A concentrated effort has been exerted in the laboratories of the Dow Chemical Co. to develop magnesium-base alloys with improved properties at elevated temperatures whereby greater advantage can be taken of the inherent lightness of these materials. In an earlier publication,1 attention was called to the superior tensile properties and resistance to creep of cerium-containing magnesium alloys at temperatures up to 700°F. More recently, additional data on magnesium-cerium alloys have been furnished by Murphy and Payne.2 The present paper deals with the mechanical properties of sand-cast magnesium alloys containing zinc, at temperatures up to 500°F. The study includes binary Mg-Zn† alloys containing up to 10 pct zinc and several ternary and some polynary alloys based on the Mg-1Zn,†Mg-3Zn, Mg-4.4Zn, Mg-6Zn, and Mg-10Zn binaries. The compositional variation in the tensile properties, hardness, and creep at room and elevated temperatures, and in the electrical conductivity at room temperature has been determined. The results of these tests show that many zinc-containing magnesium alloys exhibit resistance to creep at elevated temperatures significantly higher than that of present commercial magnesium alloys, but lower than that of alloys of the magnesium-cerium type. In addition, they have high tensile properties at room and elevated temperatures and high conductivity. This combination of mechanical properties and conductivity indicates that these alloys should be given serious consideration for commercial applications involving exposure to temperatures higher than those to which present commercial magnesium alloys can be taken safely. LITERATURE The properties of sand-cast magnesium alloys containing zinc as a principal alloying element have not been investigated very extensively, especially at elevated temperatures. The following remarks, which are confined to sand-cast alloys, will serve as a summary of the most important references on this phase of magnesium metallurgy. The first recorded determination of the tensile strength of binary Mg-Zn alloys as a function of zinc content was reported by Aitchison.3 Similar studies, including the measurement of elongation and hardness, have been performed by Gann and Winston,4 Dumas and Rockaert,5 Haughton and Prytherch,6 and by Spitaler, the last being reported by Beck.7 A slight superiority in the tensile strength of chillcast Mg + 8 Zn alloy over the sand-cast alloy was noted by Maybrey 8 That alloys of magnesium containing 5 to 12 pct zinc

Jan 1, 1948

By Wayne Loel

The application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and undcr varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarinc geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions. Introduction The following paper is in no sense a contribution to knowledge; it is merely an attempt to indicate some of the benefits that may be expected from the use of aerial photographs in geologic mapping and to mention some inherent limitations. The writer has used aerial photographs in his own work for the past 13 years and has had ample opportunity to observe their use in the hands of others. From this experience certain conclusions have been drawn, which may be helpful to those using aerial photographs for the first time. It must he remembered that a photograph of the earth's surface can delineate only that which the eye can see; therefore the geologist should not expect more from an aerial photograph than he would be able to observe were he in the photographer's airplane looking at the area to be photographed. Theoretically, if the geologist had sufficient artistic ability, he could draw as good a geologic map from his position in the plane as he could from observation of the photograph. Practically this cannot be done because the airplane moves at a high rate of speed, which in itself prohibits detailed observation and, no matter how great the geologist's artistic ability, he could not reproduce the detail that can be recorded by a camera. An aerial photograph is a picture map of an area. The picture may be studied in the office until the geologist is thoroughly familiar with every minute detail of the surface of the ground he is about to geologize. If it is an area, underlain by sedimentary rocks, much may be learned

Jan 1, 1941

By Wayne Loel

The application of aerial photographs to all phases of geologic mapping is set forth, indicating the advantages to be gained in different types of country and undcr varying climatic conditions. Methods of field and office procedure are given from a geological point of view, as well as suggestions regarding the best methods of aerial mapping for different uses and under varying field conditions, including the study of submarinc geology. Aerial photographs with accompanying geologic maps are shown to illustrate the appearance from the air of different geologic features under varying climatic and topographic conditions. Introduction The following paper is in no sense a contribution to knowledge; it is merely an attempt to indicate some of the benefits that may be expected from the use of aerial photographs in geologic mapping and to mention some inherent limitations. The writer has used aerial photographs in his own work for the past 13 years and has had ample opportunity to observe their use in the hands of others. From this experience certain conclusions have been drawn, which may be helpful to those using aerial photographs for the first time. It must he remembered that a photograph of the earth's surface can delineate only that which the eye can see; therefore the geologist should not expect more from an aerial photograph than he would be able to observe were he in the photographer's airplane looking at the area to be photographed. Theoretically, if the geologist had sufficient artistic ability, he could draw as good a geologic map from his position in the plane as he could from observation of the photograph. Practically this cannot be done because the airplane moves at a high rate of speed, which in itself prohibits detailed observation and, no matter how great the geologist's artistic ability, he could not reproduce the detail that can be recorded by a camera. An aerial photograph is a picture map of an area. The picture may be studied in the office until the geologist is thoroughly familiar with every minute detail of the surface of the ground he is about to geologize. If it is an area, underlain by sedimentary rocks, much may be learned

Jan 1, 1941

Established as a Division December 15, 1948 Evan Just, Chairman Richard J Lund, Past Chairman Granville S. Borden, Vice-Chairman J K Richardson, Vice-Chairman S H Williston, Vice-Chairman Allan Matthews, Secretary-Treasurer National Security Resources Board 17th and Pennsylvania Ave, N W Washington 25, D C

Jan 1, 1952

(There are 82 Local Sections in the United States, 10 Foreign) ADIRONDACK Established June 18, 1952 Official year begins in January Meets next to last Saturday monthly April through October Local Section Dues AIME Mbrs $2 Affiliate Mbrs $3 Severn P Brown, Chairman George E Erdman, Vice-Chairman Patrick F Farrell, Secretary-Treasurer Republic Steel Corp Mineville, N Y

Jan 1, 1960

By James H. Hance

Discussion of the paper of JAMES H. HANCE, presented at the New York meeting, .February, 1916, and printed in Bulletin No. 110, February, 1916, pp. 299 to 326. FREDERIC P. DEWEY, Washington, D. C. (communication to the Secretary*).-I wish to congratulate Professor Hance and to thank him for his extremely valuable addition to the fund of data upon this subject. It presents clearly conclusive and incontrovertible proof of the unreliability of drill samples of this class of metal for determining the value of such bullion. I am afraid, however, that his hope that some one in the mint service might continue such an investigation upon a more elaborate and exhaustive scale is, for the present at least, doomed to disappointment. As a practical matter, the mint service is not now particularly interested in segregation in crude bullion. So much trouble and friction arose, -both in the original purchase and in the transfer from one institution to another, in handling segregated bullion, that it became necessary to adopt drastic measures and now it is seldom attempted to determine the value of such bullion in the service. When bullion known or even suspected of being segregated is presented for purchase, it is at once strongly refined in the pot and the disturbing elements so far removed that concordant assays may certainly be obtained from the dip samples and a reasonably fair agreement obtained from drill samples. The mint service prefers that the owner should refine his bullion himself, but if he does not we will do it at his expense and return the slag to him when desired. Much work has been done in the mint service trying to arrive at the value of deposits of segregated bullion without strong refining. It was no unusual thing for such deposits to be melted three times at the purchasing office and to have 30 to 40 assays on the metal made before buying it. Yet when shipped to a mint it was found necessary to melt two or three times more and to make 15 to 25 assays before the mint would accept the bar, and there were considerable differences between the valuations of the two offices. In what was undoubtedly the worst case ever investigated, the purchasing office melted the deposit, 953 oz., three times, with a loss of 105.5 oz., and made 46 assays; the mint melted three times, with a loss of 6.6 oz., and made 28 assays. The mint allowed the purchasing office 1.178 oz. of fine gold more than the purchasing office claimed, while an extensive investigation of the mint samples by the Bureau, in which over 100 independent assays were made in various service laboratories, indicated that the metal carried 0.7 to 0.9 oz. more of fine gold than the mint allowed. Preliminary assays on the original metal

Jan 5, 1916

By Alfonso Rizo-Patrón, A.M. Gaudin

Previous studies of activation in flotation have directed attention to the action of the activator on the mineral to be floated rather than to the relationship of the activator to the collector. The latter phase of the problem, however, seems to have definite scientific, if not also practical, interest. In the investigation reported in this paper, experiments were carried out, largely with quartz as subject, barium as activator, and oleate as collector. The results obtained indicate that a I: I ratio of collector ion to activator ion gives optimum results, and that a 2:1 ratio almost fails to achieve activation and flotation. Yet, a 2:I ratio would have been expected on stoichiometric grounds, had the coating been a normal salt of the activator ion with the collector ion, since barium is a divalent cation and oleate a monovalent anion. To interpret and rationalize the observations, considerations of the crystal chemistry of quartz are helpful. The point of view to which these considerations lead may be of general applicability to systems involving suspensions of solids in liquids; they confirm that an adsorbed coating is inescapable. Apparatus and Supplies The experimental work consisted in barium-ion abstraction tests, hydrogen-ion and hydroxyl-ion abstraction tests, flotation tests, and determinations of the surface of the crushed quartz. The flotation machine was built according to the design of D. W. McGlashan.* It consists of a drill press in which the bit has been replaced by a stainless-steel impellor surrounding a stainless-steel sta-tor, as in the Fagergren laboratory machine. The air intake is controlled by a valve, and the cell consists of a beaker. The quartz was obtained from vein quartz stored in large chunks. It was first crushed to 20 mesh, then sized on a 28-mesh screen. The 20 to 28-mesh size alone was retained for use. This size was freed of coarse iron by passage through a Ball-Norton magnetic separator, bleached with boiling hydrochloric acid to remove residual abraded iron, washed with distilled water until the washings were thoroughly free of ferrous, ferric, and excess hydrogen ion, and stored in covered Pyrex beakers under water until used. The barium was used as barium chloride, Baker's analyzed C. P. The oleate was used as sodium oleate. It was prepared from sodium hydroxide, Baker's analyzed C. P., and oleic acid purified by R. R. de Arellano3 in the laboratories at the Massachusetts Institute of Technology. The purification procedure was elaborated from the recent $researches of Brown and Shinowara.2 It consisted in: (I) saponification of olive oil with potassium

Jan 1, 1943

By Alfonso Rizo-Patrón, A. M. Gaudin

Previous studies of activation in flotation have directed attention to the action of the activator on the mineral to be floated rather than to the relationship of the activator to the collector. The latter phase of the problem, however, seems to have definite scientific, if not also practical, interest. In the investigation reported in this paper, experiments were carried out, largely with quartz as subject, barium as activator, and oleate as collector. The results obtained indicate that a I: I ratio of collector ion to activator ion gives optimum results, and that a 2:1 ratio almost fails to achieve activation and flotation. Yet, a 2:I ratio would have been expected on stoichiometric grounds, had the coating been a normal salt of the activator ion with the collector ion, since barium is a divalent cation and oleate a monovalent anion. To interpret and rationalize the observations, considerations of the crystal chemistry of quartz are helpful. The point of view to which these considerations lead may be of general applicability to systems involving suspensions of solids in liquids; they confirm that an adsorbed coating is inescapable. Apparatus and Supplies The experimental work consisted in barium-ion abstraction tests, hydrogen-ion and hydroxyl-ion abstraction tests, flotation tests, and determinations of the surface of the crushed quartz. The flotation machine was built according to the design of D. W. McGlashan.* It consists of a drill press in which the bit has been replaced by a stainless-steel impellor surrounding a stainless-steel sta-tor, as in the Fagergren laboratory machine. The air intake is controlled by a valve, and the cell consists of a beaker. The quartz was obtained from vein quartz stored in large chunks. It was first crushed to 20 mesh, then sized on a 28-mesh screen. The 20 to 28-mesh size alone was retained for use. This size was freed of coarse iron by passage through a Ball-Norton magnetic separator, bleached with boiling hydrochloric acid to remove residual abraded iron, washed with distilled water until the washings were thoroughly free of ferrous, ferric, and excess hydrogen ion, and stored in covered Pyrex beakers under water until used. The barium was used as barium chloride, Baker's analyzed C. P. The oleate was used as sodium oleate. It was prepared from sodium hydroxide, Baker's analyzed C. P., and oleic acid purified by R. R. de Arellano3 in the laboratories at the Massachusetts Institute of Technology. The purification procedure was elaborated from the recent $researches of Brown and Shinowara.2 It consisted in: (I) saponification of olive oil with potassium

Jan 1, 1943

By Bennett Bates

A PAPER presented in South Africa' during 1925 by H. A. White gave a formula to express the efficiency of classification. The formula was originally developed by H. W. Newton of The Dorr Co. The derivation of this formula is as follows: Where E = Over-all efficiency of classifier Eu = Efficiency with respect to sand discharge Eo = Efficiency with respect to overflow I = Tons feed to classifier (input) 0 = Tons overflow U = Tons sands (underflow) i = Fraction of oversize in classifier feed o = Fraction of oversize in overflow u = Fraction of oversize in sands

Jan 5, 1927

By T. A. Wright

The sampling of waste materials containing copper, lead and tin has taken on a new significance within recent years, and is of increasing importance, on account of the entry of some of the copper refineries into this field and the tendency towards consolidations among the smelters. In the past, such material was sold on the basis either of a rough or grab sample or of casual inspection of the lot. The two principal sources of this waste are the processes of fabrication and the scrapping of automobile, electrical, plumbing, railroad and other equipment. In both cases much material can be sorted, salvaged and sold by classification and grade to be melted "as is" or with the addition of new or virgin metal. The increasing care in classifying exercised in the large manufacturing plants tends to increase the proportion of this usable scrap; on the contrary, the increasing use of more complex and special non-ferrous alloys tends to make sorting and grading more difficult in turnings, borings, clippings, etc., and consequently is making sampling of more moment. In tin, lead, aluminum, and zinc furnace by-products such as ashes, drosses, skimmings, etc., the trade practice of evaluation has not varied much. For instance, tin drosses, battery lead, and aluminum skimmings are ordinarily sold on what is called "metallic button" or "metallic recovery" or ('metallic yield." Copper and lead waste, however, is being sold more and more on actual copper and lead contents based on sample and chemical analyses. This paper will be devoted chiefly to the sampling of materials suitable only for refining and recovery of one or more of the metals present. The methods described are often based on the fact that but one metal, such as copper, is to be paid for. The loss of volatile constituents in melting does not appreciably affect the final copper result, as the "after-melting" assay can be readily calculated to the "before-melting" basis, but if smelter efficiency continues to increase, so that in time zinc, for instance, may be recovered on a paying basis, the method of sampling dirty brass, for example, will have to be changed also. As a matter of fact, we may expect that improved refining processes will make possible the partial recovery of lead and tin which are now lost.

Jan 1, 1928

By S. E. Haszko

Fused alumina or silica crucibles were used as the containing vessel. X-ray powder photographs were taken with CrKa radiation and the use of Straumanis type Norelco cameras of 114.6 mm diam. Crystallographic data for these compounds are shown in Table I. These results are in agreement with others of this series reported previousiy by Wernick and Geller.l The abnormally large atomic volume of Eu and Yb metal3 is manifested in EuA12 and YbAl2, when one compares them with the compounds reported in Ref. 1. However, the behavior of Yb in the Ni compound is the same as that observed in Ni5Yb having the Cu5Ca structure.4 Thus, it appears that Yb has a valence closer to 3 only in the Ni compounds; i.e.. the 2s and Id electrons are lost to the conduction band. 1,4 Europium in EuAl2, appears to have a valence closer to 2. In previous work.' X-ray patterns of ingots of NdCo2 indicated a multiphase material with faint indication of the presence of a phase having the MgCu2 structure. It was thought that NdCo2 formed peri-tectically from the melt, resulting in a multiphase system when cooled under nonequilibrium conditions. An X-ray pattern of a sample from a melt cooled more slowly than in past work showed that the major phase was NdCo2. The lattice constant, Table 1, is in excellent agreement with the value one can predict from the data of Ref 1. One of the other phases was identified as Co,Nd. The author wishes to thank J. H. Wernick for his guidance in this work, and D. Dorsi for the preparation of these compounds. 'J. H. Wernick and S. Geller: AIME Trans., in press. 'J. H. Wernick and S. E. Haszko: to be published. 'F. H. Spedding and A. II. Daane: Progress in Nuclear Energy, Series 5, Eds.: H. M. Finniston and J. P. Howe, McGraw-Hill Book Co., 1956. 'S. E. Haszko: to be published. 'J. H. Wernick and S. Geller: unpublished work. 6J. 11. Wernick and S. Geller: Acla Cryst., 1959, vol. 12, p. '162. The Influence of Hydrogen on the Lattice Parameters of Ti-Sn Alloys A. Coucoulas and H. Margolin A reinvestigation of the lattice parameters of Ti-Sn alloys by the present authors has revealed consistently higher c and a values than those obtained by Worrier. The difference is most pronounced in the c-parameters which are, therefore, used as a basis of comparison. This discrepancy was not due to air contamination, since precautions were taken to exclude this possibility. Specimens for Debye-Scherrer photograms were prepared by arc-melting 15-g buttons of Bureau of Mines titanium and 99.99 pct Sn, with compositions of 6, 8, 10, and 12 at. pct Sn. These buttons were forged under an oxygen-acetylene torch to 1/8-in. sq rods to produce relatively fine grained material. Scale and some surface were ground off, and the rods, after wrapping in molybdenum and titanium sheet, were vacuum annealed 15 min at 800 °C to remove hydrogen. Heat treatment of one of the samples at 875°C to produce ß and reveal a at the surface showed no surface contamination. Following the vacuum treatment, the specimens were wrapped in molybdenum and annealed for 1week at 800°C under two atmospheres of argon. After water-quenching, the rods were ground so that the thickness tapered to 0.1 mm at the tips. The ground specimens were then recapsuled as previously and reannealed 1 hr at 800°C to remove cold work. The

Jan 1, 1961

By C. S. Barrett

WhEN a collimated beam of protons or other energetic particles is scattered by a single crystal, the emerging particles produce patterns that contain much crystallographic information. Calculations of the trajectories of individual particles can predict with reasonable accuracy the complete pattern (which is related reciprocally to channeling, now studied in detail6) but the task is a lengthy one which has been completed for very few cases. A many-beam dynamic diffraction calculation of the patterns would be even more difficult and in some cases may be invalid. Because of these complexities, simple methods that will predict to a rough approximation the relative intensities of the lines in films of the back-scattering patterns of a given crystal are wanted. I have found a method which, although it is not a valid computation of intensities or of film darkening by either dynamic or kinematic diffraction principles or by trajectory calculations, nevertheless is found to be useful in practice. It has been tested on several crystal types,7 and is here tested on additional ones. The method consists in first calculating the structure factor F(hk1) for the (hkl) plane, of spacing d, by the familiar equation: where the summation extends over the atoms in the unit cell and fj is the atom scattering factor of the jth atom (using tables computed for electron diffraction, preferably those computed without exchange). Then the F values are squared and summed over all the orders, n, for which F2 has an appreciable value, giving a quantity: Finally, I, is expressed as a percentage of Ic for the

Jan 1, 1970

The United States has never been a large coal exporting nation, and normally such shipments, aside from those to Canada, have been relatively small. Since the first railroad was built across the Allegheny Mountains, the imports have been quite small also, although fairly large tonnages of Canadian coal have moved into the extreme northeastern and northwestern states at times. In Table 21 are shown all data available about these shipments from 1790 to 1939, inclusive.

Jan 1, 1942