Search Documents

By L. T. Larson

The spectral reflectivity of zirconium in light of 441 to 668 nanometers (nm) wavelengths and air immersion has been determined. Bireflectance and apparent-angle -of-rotation measurements show zirconium to be optically isotropic when examined in light of approximately 484 nm wavelength. There is a direct relationship between bireflectance and the tilt of the basal pole of zirconium from the surface normal. This relationship allows the determination of the spatial orientation of the basal pole of an individual single crystal within a coarse-grained poly crystalline section to within± 2 to 3 deg for angles of basal pole tilt from 0 to 90 deg. In recent years considerable attention has been given to the quantitative determination of optical properties of opaque minerals by use of vertically incident, plane-polarized light. In particular, Cameron' and Cameron et a1.2 have developed criteria for the identification of a large number of anisotropic ore minerals based upon measurement of the apparent angle of rotation and the ellipticity or phase difference of the reflected light. It was shown by Larson and Pickle-simer3 that apparent-angle-of-rotation measurements may also be used to determine crystallographic orientations of grains of noncubic metals. In particular, it was shown that the basa.1 pole orientation in space of zirconium grains can be determined to ±3 deg for those grains with basal pole tilts of 10 to 90 deg from the plane of the section. Another, even more widely studied, optical property is reflectivity. cameron4 has commented upon measurement of the reflectance of plane-polarized, vertically incident light and Bowie and Taylor5 have made such measurements an integral part of their system of ore-mineral identification. Leow6 has reported on the spectral reflectivity of molybdenite and has used reflectivity values to calculate refractive indices and absorption coefficients. Cameron7 has made use of reflectivity values to ascertain aniso-tropic ore mineral symmetry and Piller and v. Gehlen8 have evaluated sources and importance of errors in reflectivity measurements as applied to calculation of optical constants. cambon9 has shown that reflectivity measurements using vertically incident, plane-polarized light are useful in the investigation of metals and in the identification of phases present in alloys. Bronson10 has made preliminary measurements on the optical anisotropy of beryIlium and Mott and Haines11 have published qualitative data on the intensity of light reflected from sections of bismuth, tin, and aluminum when these metals are microscopically examined under crossed polarizing plates. Koritnig12 has correlated the reflectivity of homogeneous solid solutions with their chemical compositions. From the above work and investigations in progress by this author, it is apparent that accurately determined values for the reflectance of vertically incident, plane-polarized monochromatic light from carefully polished surfaces of noncubic metals can prove useful in identification, composition determinations, and crystallographic orientation applications. Finally, reflectivity values, when measured in two media of differing refraction index and related to standards whose spectral reflectivities in these media are known, can be used to calculate optical constants such as refractive index and absorption coefficient. These constants may prove of use to those concerned with problems of electron band configuration. This paper reports the spectral reflectivity of zirconium measured in light of 441 to 668 nanometers (nm) wavelengths and air immersion. It also gives maximum bireflectance values for a prism section of zirconium in these wavelengths and shows how bire-flectance may be used to determine the crystallographic orientation of zirconium single crystals. Because of the lack of information on the reflectivities of the standards in oil immersion, no attempt is made to calculate the refractive indices or absorption coefficients although it is recognized that such values may be of fundamental importance. METHOD Single crystals of zirconium were cut by electro-discharge machining from a single-crystal rod grown from iodide bar by an electron-beam zone-melting process.13 The crystal sections were mounted in cold-setting epoxy resin and mechanically polished to a plane, uniform, bright surface. Each crystal was then chemically polished in a 26/26/43/5 mixture (by vol) of water, nitric, lactic, and hydrofluoric acids to remove the mechanically damaged and smeared surface layer. Final polish was obtained by electropolishing at 30 v in a bath of methyl alcohol and perchloric acid (98/2 by vol) at -70oc.14 Reflectivity measurements were made using a photometer system designed and developed at Oak Ridge National Laboratory and described in detail by Larson.15 Briefly, the reflectivity measuring system consists of a reflecting microscope; a double-beam, null-balancing photometer array; a mechanically driven microscope stage; and a direct X-Y readout of the reflectivity of the specimen relative to its orientation on the microscope stage. The measuring photometer receives its signal from the specimen through a slotted Wright occular placed on top of the photovisual head of the microscope. The reference photometer receives light through a flexible glass "light pipe" from a mirror in the reflecting system of the microscope. Monochromatic light is attained through use of interference filters (15-nm half-peak width pass bands) placed in front of a stabilized Vickers 12 v, 100 w, tungsten-filament, quartz-iodide lamp.

Jan 1, 1970

By Tomek Ulatowski

INTRODUCTION In 1974, Industrial Miners Mexico, S.A. (IMMSA), agent for the borrowers, was the largest privately-held mining, smelting, and refining company in Mexico (accounting for 32% of Mexico's nonferrous metal and coal production in 1974), the fourth largest company in terms of sales, and the second most profitable company in Mexico, excluding government wholly-owned and operated industries. The company was engaged in the mining, smelting and refining of coal, copper, fluorite, gold, lead, silver, zinc and related by-products for domestic consumption and export. A combination of favorable factors led IMMSA to propose an investment plan amounting to US$286 million for 1974 through 1978, of which US$150 million was to be financed. These factors included: Substantial profits in 1973 and 1974 Positive near-term outlook for metal prices Success of the reinvestment program in increasing productivity Substantial additions to proved reserves during 1973-1974 and Fiscal incentives provided by the Mexican government to stimulate investment in the mining industry. The primary purpose of the investment program was to construct a new electrolytic zinc refinery and to expand and modernize many of the company's existing mining and refining facilities. THE BORROWER Company History Compania Miners Mexico, S.A. was incorporated in the city of Monterrey in 1918 as a wholly-owned subsidery of ASARCO Inc. (formerly American Smelting and Refining Company, New York) for the purpose of mining and processing non-ferrous metals and related products. In compliance with the Government's Mexicanization program, ASARCO Inc. divested itself of 51% of its equity in Compania Miners Asarco, S.A. on June 30, 1965. Subsequently, ownership in the divested share was apportioned as follows: 15% ownership in Compania Miners Asarco, S.A. to a group of private investors, and 36% in trust for subsequent public sale. The company's name was changed to Asarco Mexicana, S.A. in 1965. Mexican ownership in Asarco Mexicans, S.A. was increased to 51% in 1967, following the purchase of the 36% share ownership held in trust, and then to 66% in 1974 when ASARCO Inc. divested itself of an additional 15% of its holdings in Asarco Mexicans, S.A. Following its 1974 divestiture of 15% of Asarco Mexicans, S.A., ASARCO Inc's ownership in Asarco Mexicana, S.A. was reduced to 34%. In 1974, the company changed its name for the second time to Industrial Miners Mexico, S.A. (IMMSA). Fiscal Agreement IMMSA entered into a fiscal agreement with the Mexican government in 1969. The agreement, which was renewed in 1974, provided for 100% of the production and export tax corresponding to the federal government with a minimum of 50% of the amount refunded to be reinvested in fixed assets. Further, the agreement permitted the company to

Jan 1, 1985

By Herluf P. Nielsen, Robert I. Jaffee

IN recent years much attention has been given to high-melting alloy systems, It has been of interest in this respect to investigate the alloys of platinum and tungsten, which were known from the literature to have very high melting points up to about 50 pct tungsten, but about which little had been published on the high-tungsten side of the system. Powder metallurgical methods were used throughout this investigation for the preparation of the alloys, utilizing electrical sintering techniques such as are used for tungsten and molybdenum. In the course of the work it was found desirable to determine fusion temperatures of the alloys, and it was possible from these and other data to draw a tentative constitutional diagram (solidus, mostly) applicable to the high-temperature part of the system. No attempt was made to determine solid solubility vs. temperature data, nor to investigate the lower temperature transformations in the solid state. Data on the microstructure, hardness, and a note on oxidation resistance of the sintered alloys were obtained. PAST WORK Müller1 determined liquidus temperatures of platinum-rich alloys to 50 pct tungsten, using a radiation method employing a photoelectric cell, and found that the melting points increased progressively from 1771°C for platinum to 2350°C for the 50 pct alloy. Microscopic evidence by Müller that complete solid solutions exist to 50 pct tungsten was not checked by Kremer2 who, according to Vines and Wise,3 found that "although the 8 pct tungsten alloy was a solid solution, the 26 pct tungsten alloy contained a eutectic or an intermediate phase." Hultgren and jaffee4 using X ray methods found continuous solid solutions to at least 33.6 pct tungsten (35 at. pct) after annealing in vacuum for 6 days at 1000°C. Vines and Wise3 report work communicated to them by E. C. Rhodes on wrought alloys to 7 pct tungsten, which showed that tungsten hardened platinum extremely rapidly, and was one of the most potent hardeners of the binary additions to platinum. Considerable quantities of 4 pct tungsten platinum wire have been produced for grids in radar tubes and for aircraft spark plugs. Some of the alloy for the latter application is made by sintering, the remainder by smelting and casting. MATERIALS The platinum powder used in this work was kindly supplied by the research and Development Laboratory of the Owens-Corning Fiberglas Corp., Newark, Ohio, It was prepared from scrap platinum. After dissolving in aqua regia and evaporating almost to dryness, the solution was worked up several times with concentrated HCI. the resultant platinic chloride was diluted considerably, and metallic zinc was added, which precipitated the platinum in a very finely divided form. After dissolving the

Jan 1, 1948

By F. W. Glaser

Iron-silicon alloys have had a great influence, in many ways, in modern industry. Silicon steels have been used almost exclusively for the construction of electrical machinery, but have also become an important material for structures which benefit by the high tensile and yield strengths of this material. In elaborating on the early history of work done on iron-silicon alloys, Greiner, Marsh and Stoughton1 went back as far as 1808, and pointed to Berzelius as the first producer of ferrosilicon. During the last twenty years some very important contributions in the form of studies of the iron-silicon system, as well as of the physical properties of these alloys, have been published. In consideration of the brit-tleness and poor machinability of alloys containing more than 5-6 pct Si, commercial interests have stimulated the research done on iron-silicon alloys, but mainly in the range of 0 to 6 pct Si. Yensen2 has shown the influence of im- purities, such as carbon, sulphur and phosphorus on the magnetic properties of 2, 4, and 6 pct Si alloys. Corson3 extended his investigation of physical properties to approximately 32 pct Si, and attributed the brittleness of the high-silicon material to the particular constitutional features of the alloys. Though mentioned earlier in the literature, the effect of nitrogen on crystal growth and magnetic permeability of iron-silicon alloys has been demonstrated recently by Morrill4 and Rostoker,5 respectively. In all the above quoted investigations, except that of Rostoker,5 sand or chill casting processes were employed for the preparation of samples. A major advantage of the powder metallurgy process is that it does away with time-consuming machining in many applications. The powder metal industry is always interested in pro- ducing a finished product employing a material which has presented considerably greater difficulties in manufacture by other methods. Steinit26 described preparation and testing of various Fe-Si alloys which were produced by the powder metallurgy process for the manufacture of armatures for small electric motors or generators. While Steinitz investigated alloys up to 6 pct Si, Rostoker5 went as high as 9 pct Si. The author7 previously discussed the diffusion of iron-silicon compacts containing 6 and 10 pct silicon. It is the object of this paper to study the progress of diffusion occurring in iron-silicon alloys by electrical resistivity measurements. All samples were prepared by pressing and sintering of compacts. Iron, silicon, and Fe-Si powders of various mesh size and compositions were employed to obtain test samples. It was assumed that complete diffusion had been obtained when the electrical resistivity reached a constant value characteristic for that particular alloy. To this end, electrical resistance measurements were used to follow the progress of alloying under various conditions.

Jan 1, 1950

By J. G. Giddings, R. Kobayashi

Residual viscosity, the ViSCOSitY at a given pressure and temperature minus the dilute gas viscosity at the same temperature, has been found to be independent of temperature for pure components and mixtures for simple molecules and light hydrocarbons. The residual viscosities for methane, ethane, propane and four mixtures were correlated as a function of reduced density and molecular weight. INTRODUCTION Earlier efforts in correlating the viscosity of light hydrocarbons and associated gases under pressure, primarily by some form of the corresponding states principle, have been reported elsewhere.7 The formal theory of corresponding states principle for viscosity from non-equilibrium statistical mechanical arguments for simple molecules has been developed by Helfand and Rice.13 The most serious obstacle to the development of a generalized corresponding states representation of viscosity data, even for simple molecules, has been the limited quantity of precise viscosity data of pure components and mixtures over a wide range of pressure and temperature conditions. Viscosity data on light hydrocarbons have recently been contributed by several laboratories.2,6,8,23,25,26 In the study of the viscosity of nitrogen, Michels and Gibson" observed that the viscosities of nitrogen as a function of density gave parallel isotherms. The same behavior has since been reported for other gases.".= The observed behavior indicates that the residual viscosity or the viscosity at a given pressure and temperature minus the dilute gas viscosity at the same temperature is a unique function of the density. Abas-Zade,1 Michels and Botzen,18 and Michels, Bot-Zen, Friedman and Sengers,19 observed similar behavior for thermal conductivity, the residual thermal conductivity being defined in a manner parallel to that of residual viscosity. Thodos and co-workers 4,15,24 applied the residual viscosity concept to the viscosity of pure monatomic and diatomic gases. Ellington and co-workers10,25 made the residual viscosity vs density plots for ethane and propane, but omitted the region below a residual viscosity of 15 micropoise and showed a systematic separation of the ethane isotherms in the low density region. Eakin correlated the residual viscosity of methane, ethane, propane and n-butane empirically as a function of density and molecular weight: Carmichael and Sage6 recently presented ethane residual viscosity vs density values in the gaseous liquid, and near critical regions as a single univariant function of density. Flynn, Hanks, Lemaire and ROSS" have contributed extremely accurate viscosity data to confirm that the residual viscosity concept is essentially correct, but may not be accurate within 0.1 per cent of the viscosity value for the gaseous state- The recent studies by Giddings12 indicate that the residual viscosity of methane, propane and each of four methane-propane mixtures are unique functions of density Over the temperature and the density ranges studied.

Jan 1, 1965

By R. F. Mehl, C. E. Birchenall

SINCE Maxwell1 first considered the self-diffusion process in 1872 its importance in the kinetic theory of matter has been recognized. Until the discovery of isotopes in 1913, a direct measurement of this quantity seemed impossible. The only information that could be gathered indirectly was for gaseous systems for which the kinetic theory was well developed. When methods of direct observation be-came available, investigations on self-diffusion were carried out in condensed phases. In metals these data are presumably of potential importance in the study of recovery, recrystallization, creep, sintering, and related phenomena. Following the pioneer work of Von Hevesy2 and his collaborators, who determined the rate of self-diffusion in lead with the naturally occurring thorium B isotope, several metals have been investigated. Pb, Ag³, Au.6,5, and Cu6,7,8,9 are examples of isotropic crystals existing in only one phase modification. Anisotropy of diffusion has been demonstrated in Bil6 and Znll. This paper is a study of a single metal in two allotropic forms and also of self-diffusion in a body-centered cubic lattice. Despite the fact that the measurements in each of the papers cited on self-diffusion in copper seem to be internally consistent to about 10 to 15 pet, the curves reported by different authors differ by factors of 2 to 4 at the same temperatures. This uncertainty may account, in part, for the failure to establish a successful correlation between the self-diffusion rates and other physical characteristics of the metals. No satisfactory theory of metallic self- diffusion has as yet been proposed to account for all the existing data and to permit estimation in other metals. Experimental Part: Two units of radioactive iron were used in these experiments, each a mixture of Fe53 and Fe59 (12). Fe53 decays by K electron capture and the emission of an X ray with a half life of about 4 years. Fe59 emits two beta spectra, one with a maximum energy of 0.26 Mev, the other 0.46 Mev, and gamma rays of 1.1 and 1.3 Mev, with a half life of about 44 days. They were present in nearly equal concentration initially. The composite half life started at about 50 days and increased as the Fe59 decayed, leaving Fe55 relatively more abundant. After aging a year, the half life was too long to measure significant decay in a month. The absorption properties also changed with time. Because of the importance of the absorption coefficient in the diffusion calculations, it was necessary to determine this quantity frequently over the period during which these experiments were carried out. This correction was unsuspected at the time of publication of notesl3 on this work and accounts for the discrepancy in alpha iron and for part of the discrepancy in gamma iron.* * The data in the present paper supersede those given in the notes entirely. In one note the scale of log D was inadvertently reversed. In addition to the correction for the drift in absorption coefficient, the D values for gamma iron at low temperatures were high owing to insuficient correction for diffusion occurring during heating and cooling through the high temperature part of the alpha range at a rate much slower than that employed in the runs reported here. The high temperature alpha rates are much higher than the low temperature gamma rates and correspond to large equivalent times at these temperatures. These experiments were discarded and new measurements taken. Independent experiments with the same activity units indicated a radioactive contaminant in the iron, but exhaustive attempts to isolate and identify it chemically failed. These experiments? indicate † These experiments will be discussed in a later publication from this laboratory. that the contaminant represented only a trace of little importance in the diffusion results. The active iron was plated from an iron chloride solution. Enough of the solution was dropped on a 1% in. square of filter paper to wet it thoroughly.

Jan 1, 1951

By Harry C. Gatos, Frank J. Bachner, Mario D. Banus

The portion of the Nb-Sn phase diagram between 75 and 79 at. pct Nb at temperatures near the liquidus has been investigated by melting alloys of known composition and examining the microstmc-tzlres resulting when these melts were quenched. The Nb-Sn samples were contained in magnesia sleeves, and were mounted in a high-pressure apparatus. It was shown that Nb3Sn me1ts by a peri-tectic decomposition and that the composition of the compound Nb3Sn at the peritectic horizontal lies between 77 and 78 at. pct Nb. Analysis of the phases present in the samples was accomplished by anodic staining techniques and an electron-microbeam analyzer. DURING the past several years a great deal of work has been devoted to the Nb-Sn system, and the bulk of this work has been primarily concerned with the intermetallic phase Nb3Sn. However, the melting characteristics of Nb3Sn have not been investigated because of the difficulty in maintaining known compositions due to tin losses by vaporization, and the added difficulty of containing Nb-Sn alloys without sample-container reaction at the high temperatures involved. This paper reports on the development of a technique for containing Nb-Sn alloys under pressure high enough to prevent tin losses at temperatures in excess of the liquidus. Using this technique, melts of known composition were made and a phase diagram near the liquidus is proposed based on the microstructures resulting when these melts were quenched. EXPERIMENTAL The Nb-Sn alloys weighing 0.7 g each were prepared in the form of cylinders. Niobium powder, -200, +325 mesh, and tin shavings with a minute amount of tin powder for a binder were mixed in the desired proportions and cold-pressed at 50,000 psi in a 0.150-in. die. This cylinder was then enclosed as shown in Fig. 1, and the entire arrangement mounted in a 2.6-in. pyrophyllite tetrahedron.' The desired temperatures (-2500°C) presented several problems in high-pressure container materials. Boron nitride, the usual sample holder, was found to react with niobium to form the nitride. However, MgO cans and plugs machined from refractory rods did not melt nor react with the sample. Thick tantalum contact disks were used to carry the large currents (~450 amps) to the graphite heater, since tantalum did not melt and had enough strength to prevent extrusion of the sample. It was further observed that the graphite heater and tantalum disks could not be in direct contact with the pyrophyllite because it melts and decomposes at these temperatures to kyanite and coesite (SiO2),2 the former reacting with graphite and the latter with tantalum to form the silicide. The use of a MgO outer sleeve

Jan 1, 1965

By E. L. Anders

The Mile Six pool is located on the La Brea-Parinas Cullcession of International Petroleum Co., Ltd., in northwestern Peru on the west coast of South America. The reservoir pressure in this pool has been maintained within 200 psi of its initial value throughout its history, and gravity drainage has played an important role in the production behavior. It has now produced 95 per cent of its estimated ultimate recovery. It is estimated that this interesting oil pool will ultimately produce 67 per cent of the initial oil in place and that the resulting residual oil saturation may be as low as 19 per cent of the pore volume (29 per cent of the hydrocarbon pore volume). An evaluation of reservoir rock and fluid characteristics and ultimate oil recovery is presented. INTRODUCTION This study of Mile Six pool was made to evaluate its performance according to latest available information. The production performance of this pool has been discussed in various articles in the past. and the reported behavior has been used as an example for application of computation procedures for gravity drainage depletion' and as an illustration of field behavior under gravity drainage or expanding gas cap drive. There have been wide variations in reported values of initial oil in place, reservoir oil volume factor. connate-water sauration, volume of effective sand, and ultimate recovery because of the paucity of reliable basic data. These various factors have been determined as accurately as practicable with the latest available information, and this evaluation is presented herein. The production history of Mile Six is an excellent example of gravity drainage depleion with effective pressure maintenance by gar injection. GENERAL Mile Six pool was discovered by cable-tool drilling in November. 1927. when well 1996 was completed in the Parinas sand. After slow development with cable tools and sporadic production. the pool was opened to continuous pro(iuction in November. 1933. and develpment was completed with rotary rigs. Pressure maintenance was started in December, 1933. by returning gas to upstructure wells. Most of the development was 'completed by 1937, but some additional wells were drilled in the period 1939-1947. and several old wells were deepened. A total of 46 oil and gas wells and 4 dry holes were drilled on approximately 7-acre spacing. Of the producers. 21 are now flowing. 2 are pumping. 44 are gas input wells. 3 are abandoned. I is a gas well shut in. and 15 are shut in because of non-commercial production or high gas-oil ratio. The locations of all wells are shown on the map of Fig. I. Total oil production on Dec. 31. 1952, was 30,867,373 bbl: cumulative gas production was 22,023,777 Mcf; and 26,410,946 Mcf of gas had been returned to the reservoir. These figures do not include oil and gas lost ill a blowout in January. 1940. GEOLOGICAL DESCRIPTION Mile Six pool is located on the northern end of a structural spur projecting from the La Brea-Negritos uplift.' The spur is probably a reflection of a basement structure. It plunges gently to the north, i broken into a complex series of fault blocks. and contain.; the Verdun Alto. Section Sixteen. and Mile Six pools. The Parinas handstone (lower Eocene!. which is the producing formation in Mile Six. occurs at an average depth of 2,200 ft in the pool and dips north and east at from 15' to 20". The pool covers an area of approximately 350 acres. Mile Six is downfaulted about 600 ft from Section Sixteen pool to the soutb. and a major fault forms its western boundarv. The north and east boundaries are formed by the intersection of the sand top with the water-oil contact which occurs at approximately 2.440 ft subsea. An original gas-oil contact probably existed at about 1.875 ft subsea. Fig. 1 presents the latest structural interpretation of the pool. and Fig. 2 is an isopach map showing thickness of the total Parinas formation above the original water-oil contact. The heavy lints of Fig. 1 are contours on the sand top, and the fine lines are contours on the fault planes. This type of straight-line structural map was developed 1)) International's geologists to reflect structural conditions where the bedding planes dip and have no curvature. 'The La Brea-Parinas Concession is highly faulted by normal fault.. The beds are flat wherever exposed. The Parinas formation is approximately 635 ft thick. and it is etimated that 62 percent II the formation is effective sand. The original oil zone was about 565 ft thick. Fig. 211 presents an electric log showing typical Parinas sand development ill Mile Six pool. The Parinas band in Mile Six i. a well-sorted. medium- to-coal-se-grained. cross-bedded sand with minor lenses of shale and small lenses and pockets of pebble conglomerate. The sand grains are subangular to rounded and consist chiefly of quartz with feldspars. biotite hornblende, and augite as accessory minerals. Because of faulting of the Parinas- formation to the east and north of the pool. there is probably l possibility of a significant, natural water drive in Mile six. The faults within the pool. as indicated in Figs. 1 and 2. are of smaller disI,laceInent and seem to act only , partial barriers to fluid movement within the reservoir. RESERVOIR CHARACTERISTICS Core analysis data are available from five wells. The data were obtained from three wells (Nos. 3401. 3586 and 3719) at the time of their completion and from well 1996 when the original liner was sidetracked and the well was deepened ill 1946. Data from well 2779 were obtained in 1943 from old cores taken when the well was deepened in 1934. From these core analyses. the average porosity was estimated to be 22.6 per cent. and the average permeability to dry ail. was estimated to be 780 and Measured productility indices varied from 3.1 to 71.4 B/D per psi differential. Specific productivity indices varied approximately from 0.1 to 0.3 B./D per psi per ft of sand.

Jan 1, 1953

By R. G. Vardiman, M. R. Achter

THERE has been interest recently in the conditions under which dislocation pipe diffusion may be observed. In order to extend the measurements to temperatures below Tm/2, where pipe diffusion becomes more important, a chemical sectioning technique was developed for silver single crystals which makes possible the removal of layers of 100A or less. The procedure is briefly as follows. Silver single crystals of 99.995 pct purity were cut in the form of discs t by 4 in., electropolished, and electropolated with Ag110 to about 1000A thickness. The thickness was determined by calibrating the activity with the weight of heavier platings, up to 10,000A. Both diffused and undiffused samples were sectioned in a two-step process. Reaction with a solution of iodine in alcohol formed a thin, even layer of AgI, which was then dissolved in a KCN solution. The reaction rate of the iodine solution varied slightly over a period of time, so that the thickness of the stripped layers, while quite even and regular for a given specimen, ranged from 65 to l00W for different specimens. This variation was checked by using a thickly plated standard with each run. Layer thickness was determined from undiffused samples by the point where the layer activity drops to half the maximum. This maximum intensity also provides, with appropriate corrections, the initial concentration per layer co. Because of the small penetration distances, it is necessary to use the exact solution of Fick's law for a source of finite thickness.' For a plating of thick- where c is the concentration at depth x. flj the error function, D the apparent diffusion coefficient, and t the time. The diffusion coefficient was obtained from the concentration-penetration data by extrapolating to x = 0 where c/co = erf h/2(Dt)1/2 Enough points were taken to impart confidence in the accuracy of the intersection, generally about ten layers. Four temperatures were used as in Table I. For best accuracy, t and h were chosen to give values of the parameter (Dt)1/2/h between 1.0 and 1.7. A typical concentration-penetration curve is shown in Fig. 1. The diffusion coefficients calculated from Eq. [I] are plotted in Fig. 2. For comparison, the high-temperature data of Tomizuka and sonder 2 which go down to 630°C are plotted as the solid line 2(a) from their expression D = 0.40 exp (-44,090/RT). Also for comparison, the lowest temperature point of Hoffman and Tumbull3 is plotted. It is apparent that our data diverge appreciably from the high-temperature extrapolation by 373°C. A better straight line fit for the low-temperature portion is obtained by subtracting the extrapolated volume diffusion coefficient from the apparent. or measured coefficient, and plotting the difference, curve (h) of

Jan 1, 1970

By Gerald J. Anderson

The Marquette District of Central Northern Michigan is the oldest of the Lake Superior iron districts with a mining history dating from 1852 up to the present. The total production of all types of ore through 1965 was 338,120, 146 long tons. Emphasis up to the 1950's was on mining the direct shipping ores; however, demands for higher-grade and better-structured ores in the last decade has resulted in a complete shift in emphasis to beneficiating the lowgrade Negaunee Iron-formation to produce high-grade iron ore pellets. The Precambrian sediments of the Marquette Range have been correlated with the Animikie Series of the Thunder Bay District, Ontario, and are contained in a westward plunging synclinorium that is approximately 3 3 miles in length and 3 to 6 miles in width. -The rock unit of major economic importance is the Negaunee Iron-formation that reaches a thickness of 2500 feet near the City of Negaunee. The primary iron content of the Negaunee Iron-formation averages 26 per cent, whereas the altered iron-formation approximates 31 per cent. The Negaunee Iron-formation has been divided into three principal types: diagenetic, oxidized, and metamorphic. The ores produced to date fall into four categories: high-grade soft ores, high-grade hard ores, siliceous ores, and concentrates and agglomerates (pellets). The soft ores generally are found in synclines and in fault-trough structures, bounded by mafic dikes along at least one side, and are mainly found in the basal portion of the Negaunee. In contrast, the hard ores occur in the uppermost portion of the Negaunee and are controlled by structural features such as folds, faults, and dikes. Iron-formation that has undergone diagenetic and metamorphic alteration makes up the main beneficiating ore types. Studies on the Negaunee Iron-formation have played an important role in the formulation of many of the theories on the origin of the Precambrian iron-formations.

Jan 1, 1968

By C. Law McCabe, R. G. Hudson

The Knudsen cell has been employed to determine the free energy of formation of Mn7Cs in the temperature range 800" to 950°C. A value of 66,440 cal was found for hH°o for a-manganese. Measurements of the pressure of manganese over a mixed carbide, (Fe,Mn),C, points to a power relationship between aun7cs and N.4,. RECENTLY Kuo and Perssonl have reported that the carbide of manganese which is in equilibrium with graphite at temperatures up to 1100° C is Mn7Ca. There are no published data on the thermo-dynamic properties of this compound. In order to determine the stability of Mn7Ca, it appeared that, by obtaining the pressure of manganese above 8-manganese and also above Mn,C, in equilibrium with graphite, the free energy of formation of Mn7Ca from 8-manganese and graphite could be obtained. In addition, the vapor pressure of manganese, reported by Kelley From data of Bauer and Brunner,' is subject to some uncertainty and further determinations of the vapor pressure of manganese seemed warranted. In this investigation of the pressure of manganese vapor above pure manganese and also above the carbide of manganese in equilibrium with graphite the apparatus used is the Knudsen orifice cell. The same apparatus, experimental procedure, and method of calculating the pressure was used in this investigation as in one previously reported.~ Care was taken to insure that the cells were at constant weight before using them in a run. The manganese charged in the cell was CP grade powder, carbon free, obtained from the Fisher Scientific Co. A spectroscopic analysis of the manganese after appreciable amounts of it had vaporized from the Knudsen cell showed that no element was present in sufficient quantities to contribute to a weighable weight loss or to decrease the vapor pressure of manganese to any appreciable extent. The spectro-graphic analysis was 0.002 pct Cu, 0.05 pct Fe, 0.002 pct Pb, and 0.002 pct Ni. 8-manganesea is the allo-tropic form of manganese which was present in the cell at temperatures used in this investigation. The manganese carbide, Mn,Ca, was made in the following way: In a closed graphite cell manganese powder was added to graphite powder, which was made from graphite rods for spectrographic use. The manganese powder was the same as that described previously; 5 pct excess graphite was added over that required for the formation of Mn7C,. The mixture was heated in a closed graphite cell for approximately 20 hr at 1350°K under vacuum. X-ray analysis revealed that there was no manganese present after this treatment, but that the lines due to Mn,C, were present. In order to prove that there was no volatile carbide of manganese which was effusing out of the cell, the following experiment was performed: A graphite effusion cell containing graphite power, in excess of that to form Mn,C, of a desired amount, was brought to constant weight on heating at 1228°K. The required amount of manganese was accurately weighed and then added to the graphite effusion cell. The cell was placed in a vacuum at 1228°K for one week, which was the time calculated for the manganese to have effused completely, assuming instantaneous formation of Mn,C8. The cell was then weighed again. This experiment was carried out on two different occasions and both times the weight loss of the cell came within 1 pct of the weight of manganese originally charged minus the weight of manganese left in the cell, as determined by chemical analysis. These data are summarized in Table I. This agreement is considered to be within experimental error and is taken as proof that no carbide of manganese is volatile in this temperature range. It was established, by X-ray analysis, that Mn,C, formed before appreciable amounts of manganese vaporized from the metal powder which was charged. The identification of the carbide of manganese which was present in the Knudsen cell in equilibrium with graphite and manganese vapor was carried out by Kehsin Kuo at the University of Uppsala. He established that the authors' sample, which was submitted to him for analysis, contained the phase

Jan 1, 1958

By J. E. Hilliard, H. E. Cook

It is shown that for systems having a miscibility gap the spinodal composition (c,) in the vicinity of the critical temperature (Tc) is related to the equilibrium composition (c,) by where cc is the critical composition. This expression is exart for the limit T — Tc and is a good approximation down to (T/Tc) - 0.9. If the miscibility gap meets the composition of the pure components THE recent theoretical treatment by cahn1,2 on spinodal decomposition of solid solutions has revived interest in methods of estimating the chemical spinodal, * i.e., the locus on a binary phase By use of the appropriate expression, the spinodal can be drawn on the Phase diagram almost by inspection with an accuracy comparable to that of lengthy calculations in which a free-energy function is fitted to the phase diagram. Satisfactory agveemenf is also obtained with spinodals comPuted from experimental free-energy curves. where G is the Gibbs free energy of the homogeneous solution and c the atomic fraction of component 2, the derivative being evaluated at constant temperature (T) and pressure (P). (These subscripts will hereafter be omitted from the partial derivatives.) If experimental measurements of G as a function of c and T are available in a single-phase region above the spinodal, then these can be extrapolated to obtain a series of metastable free-energy isotherms in the two-phase region, and from these isotherms a series of spinodal compositions can be calculated. Because the value of is very sensitive to experimental errors, an elaborate analytic procedure is required for

Jan 1, 1965

By W. C. Hagel, H. J. Beattle

DURING an earlier examination of high-temperature alloy, A-286, the presence of an unknown intermetallic compound was verified by X-ray diffraction. Owing to its prominent appearance at grain boundaries, the arbitrary name of G phase was assigned.' Low-silicon, vacuum-melted heats were found to contain no G phase, and this investigation was initiated to determine the influence of silicon on G-phase formation; additional work was undertaken to extend existing data on other intermetallic compounds and the aging reactions in this group of alloys. Taylor and Floyd2-4 observed that the Ni3Al phase (y') and the Ni8Ti phase (7)) are the only equilibrium intermetailic compounds in nickel ternary alloys containing up to 25 pct Cr and 10 pct Ti or Al. They found that y' can dissolve considerable nickel, chromium, and titanium, although the stoichio-metric composition of 7 remains fixed. Nordheim and Grant5 confirmed that age hardening of 80 pct Ni-20 pct Cr alloys of the Nimonic-80 type is due to precipitation of y', where aluminum is partially replaced by titanium. They suggest that optimum hardness and ductility result from increasing the titanium to aluminum ratio toward the end of the y' solubility range and from increasing total titanium and aluminum content to the maximum limit permitted by processing. Such information is necessary for those seeking to improve the service-temperature range and long-time structural stability of high-temperature components. Experimental Methods Compositions of materiais studied. are listed in Table I. Alloys D, E, and F possess representative A-286 analyses; silicon increases from less than 0.02 to 1.75 pct in alloys A to H; in alloys I to K, titanium decreases from 2.24 to 0.39 pct, and aluminum increases from 0.1 6 to 240 pct. Alloys A and D were solution heat treated for 4 hr at 1700°F, oil quenched and aged for 0.5, 2, 6, 12, 30, 70, 200, and 1000 hr at 1200°, 1300°, 1400°, and 1500°F. Therefore, a total of 33 specimens was required for each

Jan 1, 1958

By O. F. Kammerer, W. E. Miller, D. H. Gurinsky, J. Sadofsky, J. R. Weeks

Zirconium and titanium inhibit solution mass transfer of steels by liquid bismuth, mercury, and lead. It is shown that in bismuth and mercury, these adsorb on the surface of the steels and subsequently react with nitrogen and possibly carbon from the steels to form inert, adherent surface layers of ZrN, TiN, or TiN + Tic. Data are presented which describe the condition under which thase deposits form. These inhibitors decrease the solution rate of iron into bismuth, and require a higher supersaturation for precipitation of iron from bismuth. USE of the low-melting heavy metals (bismuth, lead, mercury, and their alloys) as coolants has been limited because solution mass transfer of steels occurs in these liquids; i. e., iron dissolves in the hot sections of the heat transfer circuit and deposits in the colder sections. The rate of solution of iron and the temperature coefficient of solubility are sufficiently great to cause complete or partial stoppage by the deposition in the coldest section of a closed circuit in finite time, even though the actual solubilities are extremely low. In the development of the mercury vapor turbine by the General Electric Co., Nerad and his associates1 discovered that the addition of as little as 1 ppm Ti or Zr to magnesium-deoxidized mercury reduced the mass transfer of ferrous alloys by mercury to a negligible amount. Reid2 reported that titanium was detected chemically on the surface of steels contacted with this mercury alloy in amounts varying from 2.0 to 2.6 mg per sq in., the greatest amount being found in the hottest portion of the circuit. Reid stated that the titanium forms the intermetallic compound Fe2Ti by reaction with iron on the surface of the steels. This compound was presumed to be highly insoluble in mercury. More recently, El-gert and Egan3 have reported a greater than 100-fold reduction in the rate of mass transfer of a 5 pet Cr steel by liquid bismuth upon the addition of titanium (in excess of 50 ppm) and magnesium (350 ppm) in the liquid metal, during experiments performed in thermal convection loops* over the temperature differential 700° to 615° C. Also, Shep-ard and his associates' have reported that the addition of titanium to liquid bismuth and Pb-Bi eutec-tic produced a marked decrease in the rates of solution of both iron and chromium from type 410 steel capsules under static conditions. This inhibiting effect increased with repeated reuse of the capsules. Tests performed in this laboratory under carefully controlled conditions have shown that the addition of zirconium and magnesium, or titanium and magnesium, to liquid bismuth or lead greatly reduces the rate of mass transfer of chromium alloy steels and carbon steels in thermal convection loops with a maximum temperature of 550°C.5-9 The present paper will review the data obtained to date at this laboratory on the behavior of iron and steels in contact with liquid bismuth alloys containing titanium or zirconium, and will attempt to explain the role of the above additives in reducing solution mass transfer. Reaction between the Zirconium or Titanium Dissolved In Liquid Bismuth and an Iron or Steel Surface Reaction between Zirconium Dissolved in Bismuth and the Surface of Pure Iron-—A small pure iron crucible (analyzed by the supplier to contain 0.8 ppm N was contacted with bismuth containing approximately 0.1 pet Mg and varying amounts of a radioactive zirconium tracer. The crucible was then inverted at the temperature of contact. The thin residual layer of adherent bismuth was dissolved in cold, concentrated nitric acid. The crucible surface and the solidified bismuth were then analyzed for radioactive zirconium. An analysis of the activity loss on the crucible surface and the weight loss of the crucible during the nitric acid treatment showed that the acid treatment removed the zirconium that had originally been dissolved in the adherent bismuth, but not any zirconium that may have reacted with the crucible surface. The crucible was then pickled in warm aqua regia to remove all surface activity, hydrogen-fired at 600°C, and recontacted with a new liquid alloy. The results of the experiments contacted 1 hr at 450°C show, Fig. 1, a Langmuir-type adsorption with an adsorption free energy of approximately 17 keal per g atom Zr.5 This deposit was estimated to contain 1 atom of zirconium for each 7 to 8 iron atoms on the crucible surface, assuming a surface roughness factor of the pickled crucibles to be five. Increasing the temperature to 520°C caused consi-

Jan 1, 1959

By J. D. Lubahn

The influence of precipitation from solid solution on the subsequent deformation resistance of alloys is well known. However, the influence of precipitation or aging that occurs simultaneously with deformation may be entirely different and of considerable importance. It is thought1 that the presence or absence of a yield point jog in impure iron at room temperature and the presence or absence of discontinuous flow at higher temperatures may be directly related to aging phenomena, particularly since the yield point jog is absent when the carbon and nitrogen are sufficiently removed.2 As a preliminary attack on the problem of simultaneous aging and deformation, three kinds of tests—constant strain rate tensile tests, constant load creep tests, and variable strain rate tensile tests—were carried out on an age hardenahle aluminum alloy. Constant Strain Rate Tensile Tests Stress-strain curves at a strain rale of about 0.001 min-1 were obtained for specimens of 61S that had been quenched into liquid nitrogen after a one-hour solution treatment at 521°C, then aged at room temperature 10 min., 20 min., 4 hr, and 26.5 hr before testing. Strain-time curves were obtained on the same chart with the stress-strain curve by means of an auxiliary pen, driven parallel to the axis of the chart drum at constant speed by a synchronous motor and gear chain. The angle of rotation of the chart drum was proportional to strain. The strain rates reported are the measured slopes of the strain time curves. Constant strain rate was approximated (within a factor of 2) by manual adjustment of the oil inlet valve of the hydraulic testing machine in such a way that the course of the recorder pen was parallel to pre-drawn strain-time lines of the desired slope. The specimens were machined from 9/16 in. rod. The cylindrical portion was 0.357 in. in diam by 13/4 in. long and

Jan 1, 1950

DEFENSE Materials Procurement Agency has been moving rapidly to encourage copper industry expansion programs. Although copper production is at a high level, a shortage exists on a world-wide basis as well as on the domestic scene. Projected expansion programs will not ease this current demand for most of them are 2 to 5 years off. Refining facilities are adequate but there is a shortage of ore and scrap, and it is for this reason that the expansion programs are directed at developing more sources of supply. The domestic expansion programmed thus far and understood to have been arranged with price escalation should the domestic price go to 271/20, were summarized by American Metal Markets as follows (dates of announcement are given in parenthesis: .1-Copper Cities Mining Co.'s, $15,000,000 expansion near Miami, Ariz., to be operating about 1954. DMPA will buy 22,500 tons of copper a year up to a given amount on an agreed price of 23¢ per pound, with some exceptions and depending upon salability at a higher price to other purchasers in the U. S. (September 25th). 2-An RFC loan of $60,000 to North Butte Mining Co. to be paid off on the basis of deliveries at a purchase price of 241/20 per pound (September 25th). 3-A $25,000,000 expansion program by Phelps Dodge to provide 38,000 tons per year by late 1954. DMPA would purchase it at a price of 22¢ per pound up to 112,500 tons providing other purchasers in the U. S. will not pay a higher price (September 26th). 4-Anaconda Copper Mining Co. $40,000,000 expansion in Nevada to provide more than 30,000 (might be increased to 45,000) tons per year. DMPA would purchase the copper at 250 per pound for a limited period of time if it is not salable to industrial users at above this price. Production would start around 1953 (November 14th).

Jan 1, 1952

By John Stewart

The market at present supplied by shipments from the phosphate districts of Quebec, Ontario, and New York State requires high-grade ore, carrying from 75 per cent. to 90 per cent. of phosphate of lime. In sorting out such material by hand, much valuable phosphate is necessarily left in the "culls" or refuse, besides which, much phosphate-rock of low-grade is not now mined at all, because it cannot be made available by the crude method of cobbing and hand-sorting. The utilization of such material, which would, of course, greatly benefit this industry, requires either a mechanical separation or a chemical process which would concentrate the phosphate in a form suitable for agriculture. Considering the rich phosphate now shipped as the first class, we may arrange the lower grades in three classes, as follows: Second Class.—Cull-ore from the first class, and the mass of deposits having, as gangue, pyroxene or hornblende. The following table gives the hardness and specific gravity of the minerals concerned: Hardness Spec. gravity. Apatite,....... . 5 3.1 to 3.25 Crystalline limestone (pink calcite),. 3 to 4 2.5 to 2.9 Pyroxene,..5 to 6 3.23 to 3.5 Hornblende,.5 to 6 2.9 to 3.4 Feldspar (orthoclase),. .. . 6 to 6.5 2.5 to 2.6 It is evident that when pyroxene and hornblende are present in large proportions, this ore cannot be successfully concentrated by crushing and jigging. It may be reduced to fine powder by successive treatment in a rock-breaker and a Sturtevant or Frisbee-Lucop mill, or other suitable apparatus, and in this condition it could be largely used by applying it freely upon exhausted clay soils, such as occur in Quebec and Ontario. The occupants of these once fertile river-lands are, however, hard to move in the direction of such improvements. When water-power is at hand, the cost of crushing

Jan 1, 1893

By Porter W. Shimer

(New York Meeting, February, 1912.) IT does not seem to be generally known that some American pig-irons contain notable amounts of vanadium, and while the present investigation is far from covering the whole range of irons, it is hoped that, at least, it may serve to call attention to the importance of looking for this element. The majority of the pig-irons investigated were made in the Lehigh Valley and neighboring furnaces, using more or less New Jersey magnetite in their mixtures. Many of these ores, and probably all of them, contain a little vanadium as well as titanium; the ore from one of the largest of these mines contains 0.05 per cent. of vanadium and 0.60 per cent. of titanium. Dr. Thomas M. Drown was the first to detect the presence. of vanadium in the incrustations 1 occurring on certain pig-irons, and he also found this element in a number of magnetites, but the methods for its accurate determination had not, at that time, been well worked out. In a general way, it may be said that the Lehigh Valley pig-irons contain from 0.02 to 0.05 per cent. of vanadium and from 0.10 to 0.20 per cent. of titanium. These elements follow the silicon; that is, the furnace-conditions which produce a high-silicon, low-sulphur iron will cause the maximum reduction of vanadium and titanium, and the lower grades of iron, with low silicon and high sulphur, have a lower content of these elements. The following analyses of irons made from the same mixture, but under varying furnace-conditions, show this very well Vanadium. Silicon. Sulphur. Per Cent. Per Cent. Per Cent. NO. 1 X, . . . 0.042 3.46 0.022 No. 2 plain, . . 0.038 2.26 0.041 Mottled, . . . 0.0'29 0.52 0.106 1 Robertson and Firmstone, Note Concerning Certain Incrustations on Pig Iron,Trans., xii., 641 (1883-84).

Aug 1, 1912

By Antoni Kidybinski

Mechanical properties of the nether roof rocks play a substantial role in maintenance of mine openings. On longwall faces too low strength is a cause of rock- falls which bring about delays in face advance, and hazard to the miners, while too high strength may result in over hanging of roof rocks in gobs, sometimes over a large area, initiating dynamic periodical pressures. Hence, efforts have been undertaken to develop methods of caveability evaluation for proper selection of roof control system and of longwall-face supports. DESCRIPTIVE CLASSIFICATIONS One of the basic qualitative criteria for classification of roof types with different caveability is the criterion of geological structure. The 26-stages scale worked out for conditions of Donetz Coalfield. USSR, by E.T. Proyavkin et al.(l) may be an example of that type of classification. This scale is presented graphically in Fig. 1. The first types of roofs according to this scale are easily caving immediately after exposure of a small surface, while the last be- long to the strongest roofs which over-hang in waste and require artificial fracturing. Observations and measurements carried out also in Donetz mines lead W.T. Davidyanc (2) to following classification: Class I - weak and densely bedded rocks very easily caving after each advance of supports. The roof subsidence over a waste edge is: [ ] where: h is roof subsidence, m M is thickness of the seam being mined, m S is width of an opening, m Class II - medium caveability and small main roof movements [ ] Class III - hardly breakable rocks, thicker beds with higher strength: caving by large blocks. After exposure of larger roof surfaces the movements of the main roof strata may affect an opening. [ ] Class IV - very hardly breakable rocks - thick, monolithic sandstones: they cause considerable difficulties in working with caving. [ ] Class V - thin-bedded rocks featured by the capacity of a smooth subsidence without disintegration into loose blocks with keeping contact between the particular blocks in a bed. In this classification mining with full roof caving is recommended for class I-III and only exceptionally for class IV. In many coal fields, qualitative and quantitative observations of roof rocks behavior have been carried out: as a result relations and characteristics found in certain mines are given. As an example, Kizielov Coalfield data in the USSR given by B.S. Vinokur (3) may be mentioned. In working thin pitching seams man- less system of undercutting the seam by means of rope saw is used there. The author separated four classes of roofs and gave, for every class, the empirical relation between the extracted area and the time of roof stability. The size of the stable area of exposed roof for particular classes is as follows: 120 to 150 m2 (1291 to 1614 ft2 ), 170 to 200 m2 (1829 to 2152 ft2), 250 to 280 m2 (2690 to 3013 ft2 ) and 350 to 400 m2 (3766 to 4300 ft ). For Kuznetz coalfield in the USSR the following classification of roofs was developed at the WIMI Institute in Leningrad: Class I - completely unstable: impact strength in- dex of rock f = up to 1.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 it) wide, exposed after shearer's cut holds stable during the time not longer than 5 min. Class II - low stability: f = 1.5 to 2.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 ft) wide and up to 4.0 m (13 it) long, exposed after shearer's cut holds stable during 5 to 20 min. Class III - medium stability: f = 2.51 to 3.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 it) wide and 4.0 to 25 m (13 to 82 ft) long, exposed after shearer's cut holds stable from 20 min. to 2 hours. Class IV - stable: f = 3.51 to 4.5 - the strip of roof 1.4 to 2.0 m (4.59 to 6.56 ft) wide and 25 m (82 it) long exposed after shearer's cut is stable during the time longer than 2 hours. Class V - entirely stable: f = over 4.5

Jan 1, 1982

By George Holderer

THE Enos Coal Mining Co. owns an area underlaid by coal, of approximately 5000 acres. This property is situated 9 miles from Oakland City, in the southern part of Indiana. The mine has been in operation 5 years, during which time some 350 acres have been stripped, and stripping is now proceeding at the rate of about 100 acres per year. TOPOGRAPHY These coal lands consist of gently-rolling agricultural fields which in times past were farmed for wheat. There is no timber and but very little brush to contend with. The overburden varies from 10 to 60 ft. in depth. A thin bed of slate overlies the coal, followed by limestone, which varies from 3 to 15 ft.; this, in turn, is followed by sandstone, slate, shale and clay. There is a very wide variation in the thickness of all of these beds. The coal has an average thickness of 5 ft., and is a good grade of high-volatile bituminous. MINING OPERATIONS Briefly, the sequence of operations is: drilling holes with churn drills; blasting with L. 0. X.; stripping overburden to uncover coal and, finally taking up the coal, which is sent to a tipple for cleaning and sizing. In order to show what is being accomplished by the use of L. 0. X., results will be shown from May to November, 1926, inclusive, and compared to the same period in 1925. No work was done in No. 1 pit during May, 1925, hence all figures are unduly low for this month. Drilling There are in use 8 No. 44 Loomis clipper drills, caterpillar traction with gasoline engines; recently these were equipped with extra heavy stems, measuring 26 ft. overall and 4 ½ in. dia., to increase the speed of drilling. In addition, 4 No. 1 ½ G non-traction drills have been acquired, and are used to save the time of the larger drills when recleaning is necessary.

Jan 1, 1927