Search Documents

By C. Zener, J. H. Hollomon

IT Is commonly recognized that a given material may be described as ductile or brittle only with reference to the conditions of test. Thus under the usual test conditions quartz is brittle, but under high pressures it is ductile. Salts that are brittle at room temperature become ductile at elevated temperatures. Pitch, brittle with respect o rapid loads, flows at low rates of loading. Pearlitic steel, ductile under the usual conditions of test, may be embrittled under the proper conditions of combined stresses, temperature, and rate of loading. EARLIER INVESTIGATIONS A clear analysis of the conditions necessary for plastic flow and for fracture was first given by Ludwik,1 who introduced two types of stress, the "flow stress" and the "stress at fracture." These stresses may refer to tensile or to shear stresses, or, in fact, to any type of stress. Ludwik considered these two stresses to be independent of one another, functions of the conditions of test and of the prior history of the material. For the purpose of analysis, both a flow stress and a stress at fracture can be envisaged as functions of strain over the entire range from zero to infinite strain. Thus, the material is brittle if the stress at fracture is less than the flow stress and ductile if the reverse is true. According to Ludwik's analysis, the problem of determining the effects of combined stresses, of temperature and of strain rate upon the behavior of metals reduces to a problem of determining the effect of these variables upon the flow stress and upon the stress at fracture. In the present paper, methods are described for determining the effects of two of these variables, temperature and strain rate, and examples are given of the dependence or now stress and stress at fracture, upon these two variables. The effect of combined stresses will be discussed in a succeeding paper. The flow stress may be determined from a load-diameter curve. Load-diameter curves were obtained over a wide range of temperature and over the limited range of strain rates obtainable with the lever-type Riehle machine used. The. curves were then converted to an extremely wide range of strain rate by making use of the equivalence of the effects of changes in strain rate and changes in temperature, previously proposed2 and demonstrated' by the authors. According to this principle of equivalence, strain rate E and temperature T affect the flow stress only through a single parameter p of the form: p = EeQ/RT [I] In this equation, R is the gas constant (2 cal. per gram mol per deg. C.), and Q is a heat of activation, which varies from material to material, and may depend upon the strain, but not upon the strain rate or the temperature. There is associated with every value of p a flow-stress curve. Combinations of strain rate and of temperature that give the same p have the same flow-stress curve. Therefore, merely by changing the temperature of test, the effect of changing the strain rate may be obtained. Thus, under isothermal conditions, the material will behave the same at

Jan 1, 1944

By C. F. Smart

SINCE their comparatively recent development, the alloys of cadmium with silver and copper or nickel, and of cadmium with nickel alone, have been used somewhat extensively as liners for connecting rod bearings and main bearings of internal-combustion engines. In applications where, owing to high bearing loads and elevated operating temperatures, the life of bearings made from tin-base or lead-base alloys has been undesirably short, cadmium alloys have demonstrated considerable advantage. In applications where, because of deflection of the crankshaft or bearing supports, copper-lead bearing metals have resulted in scored shafts, cadmium alloys have been operated successfully. The somewhat serious drawback to these alloys in bearing service has been that they, in common with copper-lead and certain lead alloys, are susceptible to corrosion in the presence of lubricants containing organic acids. These acids may be fatty acids (such as oleic acid) derived from animal or vegetable oils that sometimes have been compounded with engine lubricants, or they may be compounds of an acid nature developed by the oxidation of some petroleum oils under operating conditions. The result of such acid attack on bearings is illustrated by the photograph, Fig. 1. The petroleum oils that are most readily oxidized to a corrosive condi-tion, and the operating conditions under which such oxidation most readily occurs, are now rather well known among the technical organiza-tions of both the petroleum and automotive industries. While means have been developed for inhibiting petroleum oils against such acid formation, the knowledge that this condition may be encountered has been a factor in restricting the wider use of cadmium alloys as engine bearings. It has appeared, therefore, that their value and use would be enhanced if they could be made corrosion-resistant to a degree compatible with the most severe operating requirements.

Jan 1, 1938

By K. E. Gray, A. Podio

ABSTRACT Berea and Bandera sandstone samples were impacted with both 3/4-in. and 1/2-in. long wedges, each having a 60° included angle and a 0.05-in. flat, at various confining pressures, with borehole and pore pressures held fixed at atmospheric pressure. Samples were saturated with air, water, glycerine-water, solirol, mineral oil and soltrol-mineral oil mixtures to obtain a wide range of pore fluid viscosity. Penetration depth was held constant at 0.1 in. Dry and soltrol-mineral oil-saturated Berea samples were impacted at depths of penetration from 0.01 to 0.04 in. under 1,000 psi confining pressure to study crater initiation. Results indicate that viscosity of the pore fluid is influential primarily during the early stages of crater formation. Differences in bit force, crater volume and blow energy for tests parallel and perpendicular to bedding were significant, but decreased as the stress state was elevated. Crater volume, blow energy and bit force were nonlinearly related with depth of penetration. Crater volume was nonlinear with energy of blow. Fixed-penetration tests on saturated Berea yielded greater crater volume than did similar tests on dry samples. Differences in the nature of deformation for low values of bit penetration were noted between saturated and unsaturated samples. INTRODUCTION Rock failure during bit-tooth impact and scouring action constitutes a vital part of the drilling process and a difficult problem for researchers. Much study has been devoted to various aspects of the problem, and much has been learned about mechanics of rock failure. However, analytical treatment of drilling at depth remains difficult, partly because there are so many factors involved and because valid simulation of downhole conditions is extremely difficult. Forming individual craters by a bit tooth or chisel impacting, or indenting, a rock mass has been studied by many investigators.1-18 Similarity between single-tooth chisel impact and the corresponding action of a rotary bit has been discussed by Appl and Gatley, Garner, Podio, and Gatlin l8 compared the similarity in single-blow impact tests with microbit drilling data reported by Cunningham and Eenink.l9 Maurerll has used single-tooth impact data to develop a "perfect cleaning" theory of rotary drilling. Individual roller cutter-tooth impact data have been reported by Young. 20 Single-tooth tests in all of the cited literature were carried out on dry rocks. Inasmuch as any subsurface rock of oilfield interest is saturated with some fluid, it seemed desirable to study crater formation in permeable rocks saturated with a viscous pore fluid as a step, however short, toward more realistic simulation of subsurface conditions. This paper presents results of single-blow chisel impact studies on Berea and Bandera sandstones, both dry and saturated with pore fluids of various viscosities at confining pressures to 10,000 psi. EXPERIMENTAL APPARATUS AND PROCEDURE EXPERIMENTAL APPARATUS The same basic apparatus for single-blow chisel impact at elevated stress states, described in earlier papers was used in this study. l6. l8 Fig. 1 shows the complete experimental system; Fig. 2 shows a cross section of the pressure cell, with a sample ready to be impacted. EXPERIMENTAL PROCEDURE Two different rocks, Berea and Bandera sandstones, were used in this study. Both rocks have been used extensively in research, and rock descriptions can be found in a paper by Gnirk and Cheatham.15 Permeability to air of Berea is about 300 md normal to bedding and 540 md parallel to bedding. Bandera had vertical and horizontal air permeabilities of 18 and 57 md, respectively.

Jan 1, 1966

By H. L. Lovell, L. H. E. Weyher

Cyclones have been used successfully in the mineral industries to solve solid-liquid as well as solid-solid separation problems in the processing of fine particles. Substantial information is available about the operation of cyclones as thickeners, classifiers, and concentrators using a dense medium. However, very little is known about the operation of the cyclone as a fine coal concentrator not using dense medium. This application of the cyclone, namely to wash fine coal in water, requires that classification phenomena be minimized in order to arrive at an effective separation of the high density ash and sulfur-bearing mineral particles from the low density coal particles over a wide particle size range. The authors have investigated the role of feed pressure, orifice diameters, and vortex-finder length in the cyclone washing of fine coal (--1/4 in.) in water. The results of this investigation show that cyclone washing of fine coal in water is an effective unit operation particularly capable of reducing the inorganic pyritic sulfur content. The combination of hydrocyclones with complimentary equipment such as Sieve bends, shaking tables, and flotation units appears to be especially promising and may ultimately yield fine coal processing systems that could approximate the high recovery efficiencies of today's coarse coal cleaning circuits. In the future, fine coal beneficiation can be expected to receive even greater research emphasis as a result of increasing sulfur restrictions on all major coal markets. In a previous paper, work, conducted at the Pennsylvania State University, on the hydrocyclone washing of fine coal was discussed.' The initial evaluation based on that wo-rk demonstrated the feasibility of hydrocyclones as fine-coal cleaning devices, and in that previous paper selected test data were presented that showed in principle how product yield and assay respond to variations of the major cyclone operating variables. The present paper reports in greater detail on the findings and presents a comprehensive evaluation of the data as follows: (1) Hydrocyclone throughput rates were related to feed pressure and other variables by regression equations. These equations are compared with other capacity-vs.-pressure drop expressions taken from the literature on classification cyclones. (2) The flow ratio was found to be the most important variable for the separation of the solids. Control of this ratio through various cyclone operating parameters is discussed. (3) The data on the product yield as well as the ash and sulfur assays from the tests were evaluated by means of correlation and multiple regression analyses. Because size-classification phenomena cannot be suppressed completely in hydrocyclone washers, product yield and assay data are regressed against cyclone operating variables separately for different size classes. These equations then reveal how the interactions of the cyclone operating variables vary in terms of the separation for different size classes. (4) Density partitions from additional tests were analyzed by supplementing product-size analyses with sink-float analyses of the separated product size classes. The evaluation of these data show how classification phenomena affect separation by density. The results demonstrate in particular the feasibility of the hydrocyclone washer for removing pyritic sulfur from fine coal. In addition to these specific findings, the investigation points up the value, in general, of using hydrocyclone washers in combination with unit operations such as screening, table concentration, and flotation. In order to make optimum use of the hydrocyclone washers and work out the most effective combination of unit operations, it is important to have careful flowsheet analyses corresponding to the given feed and product requirements. Analyses of this kind are now possible by means of computer simulation of flowsheets and other operation research tools. INTRODUCTION Before proceeding with the detailed treatment and evaluation of our results, it will be useful to review the fundamental aspects of cyclone separators and also restate the experimental procedures and data handling employed in these studies. Review of Cyclone Fundamentals: AS shown in Fig. 1, the basic components of cyclones commonly used

Jan 1, 1970

ECONOMICS In the preceding pages you will find an attempt to judge the direction of one phase of the mining industry in Drift, and following that a quick round up of what happened to production in 1958 in Trends. Next, Charles Merrill presents a comprehensive price history for the mineral products of greatest importance, complete with figures for the past 50 years. On the following pages Nathaniel Arbiter and Charles Will Wright take a look at price trend prospects and the cold war in mining, respectively. MINERALS BENEFICIATION Fifty years progress is reviewed as a springboard for a look ahead. In the past decade the art has moved forward, but the author fears that the science is not progressing as promisingly.

Jan 2, 1959

By Y. C. Liu, R. H. Richman

Deformation and recrystallization textures of the a solid solutions of Cu-P, Cu-As, and Cu-Sb alloys are examined as a function of composition. It is found that the deformation texture of copper is unckanged up to a composition of 0.43, 0.41, and 0.24 at. pct of phosphorus, arsenic, and antimony, respectzvely, and then the transition to the 70 : 30 brass type of deformation texture proceeds linearly as the logarithm of the solute content. Recrystallization textures consist of strong, new components that do not all bear the usual<111> rotational relation to the deformation components. The dependence of the deformation texture transitions and the recrystallization orientations upon composition and solute-element type is discussed. A systematic evolution of individual recrystallization components in the annealing texture of copper was portrayed as a function of germanium or tin content in a previous study.&apos; Similar patterns of tex-tural change have been observed with copper-zinc alloys,2 and in less detailed studies of other systems.3,4 In fact, most of the literature dealing with preferred orientations in copper alloys indicates that the influence of solute elements upon textures in copper is of one general type. As the alloy content of copper is increased, the deformation texture changes from the copper type to the 70:30 brass type, and the annealing texture undergoes a comparable change from the (001) [ loo] orientation of unalloyed copper to the {113} <211> type of 70:30 brass, with the notable exception of copper alloyed with Periodic Subgroup V-B elements.4-8 In almost every case it is possible to describe the reorientations after annealing as 30 to 40 deg rotations about <1ll> poles of the deformation components. Since there is apparently not much difference in the final textures of the copper binary systems already investigated, only a limited variety of preferred orientations has served as the basis for current theories of the origin of annealing textures. In order to test the validity of the proposed theories, and the possibility that the <111> rotations are not unique, it would be most desirable to study the reorientation relationships of additional, and heretofore unanalyzed, recrystallization components if such components exist. Examination of the literature reveals a good deal of uncertainty concerning preferred orientations in copper alloyed with elements in Subgroup V-B of the Periodic Table. Phosphorus is known to inhibit the cube texture in copper when present in amounts as low as 0.01 wt pct,8 but the recrystallized matrix that occurs instead of the cube orientation was reported as either random or weakly textured, with orientations not observed in Cu-Zn, Cu-Ge, or Cu-Sn alloys.4-9 A Cu-0.75 at. pct As alloy apparently contained, along with the (001)[100] and (113) <211> type of recrystallization components, {110} <112> and (110) <001> components, whereas an almost random distribution of orientations was found in alloys of higher arsenic content.4 A {110} <001> component also appeared in rolledand annealed Cu-Sb alloys, but otherwise the recrystallization textures of Cu-Sb alloys seem to con-

Jan 1, 1962

By Milton Fies

ALTHOUGH pig iron from iron ore and red cedar charcoal preceded the mining of coal by many years, for tradition says that Alabama iron was used to shoe the horses of Andrew Jackson&apos;s soldiers, coal was not produced until 1830. In that year, coal was mined in Tuscaloosa County, in the vicinity of what is now the University of Alabama, and shipped on flat boats (obviously during the wet season, for there were many shoals) down the Warrior River to Mobile. About that time, the first railroad, the Decatur & Tecumseh, was being constructed in northern Alabama to overcome the obstructions to freight traffic caused by the now well-known Muscle Shoals in the Tennessee River. This railroad was patterned after a railroad at Mauch Chunk, Pa., which was used for hauling anthracite from the Panther Creek valley. The Alabama railroad, which required about four years to complete, was 46 miles long and was used solely for the transportation of cotton. Although it was a failure, it demonstrated the practicability of the undertaking, and the succeeding railroads, which were begun in 1834, 1848, 1852, and 1853, added immeasurably to the development of the coal resources of the state. Between the years 1830 and 1860, practically all the coal mined in the state was dug from the outcrop near the river or from the river beds, and shipped by boat to Mobile. Transporting coal down the Warrior River was one of great risk, required much skill, and frequently had heavy losses. It is recorded that this coal was sold to the gas company in Mobile in 1844; it was most likely mined from the Black Creek Seam. In 1914, on the completion of Lock 17, the Warrior River became a navigable stream from 9 miles above Cordova, Ala., to Mobile and offers a great opportunity for the future development of the coal resources of the state.

Jan 9, 1924

By R. A. Salathiel, A. D. Kaiser, P. H. Monaghan, B. E. Morgan

The productivities of many hydrocarbon-bearing for-rnntions appear to be reduced during drilling, completing and repairing operations. The reason for these othcarwise unexplainable low productivities may be a drastic reduction of formation permeability immediately surrounding the borehole. A possible cause of the reduced permeability is swelling and dispersion of clays present in porous media when contacted by fresh water or mud filtrates. Hence, the invasion of fresh water or mud filtrate into hydrocarbon-bearing formations that contain clays may cause low productivities as a result of formation damage. Present laboratory investigations have yielded results which supplement existing literature on formation damage. An expanded-type clay, montmorillonite, way found in hydrocarbon-bearing formations not previously analyzed. When sand columns and formation cores containing montmorillonite were contacted by fresh water, their oil permeabilities were reduced. This reduction in oil permeability way restored partially but not completely by a repair procedure, i.e., flooding with kerosene containing organic agents or flooding with water containing electrolytes. Hence, where montmorillonite is present in formations, prevention of formation danzage was indicated to be the only complete solution to the problem. To prevernt formation damage, results suggested use of an approximately 1 per cent solution of calcium chloride or stronger solutions of sodium or potassium chloride. In conventional rotary drilling operations the wall of the hole is exposed to drilling mud for days, weeks, and in some instances for as long as several months. During this time, drilling mud filtrate seeps slowly into formations surrounding the hole. The permeability and stability of many formations, especially those containing clayey materials, are impaired by the mud filtrate. Often interaction between the mud filtrate and the formation causes drilling and production difficulties. Serious reduction in productivity of oil and gas formations during drilling, completing and repairing wells has been noted often in recent years. Cases are known of development wells which produced only small volumes of fluid upon completion. However, after a period had elapsed, they began to produce oil or gas in commercial quantities. In other cases, results of drill-stem tests taken during the drilling of deep wells have indicated good production should be obtained from shallow formations. Later difficulty has been experienced in obtaining production from these shallow formations which had remained in contact with drilling muds for an extended time. In yet other cases wells have failed to attain the productivities expected from previous performance after the use of drilling mud as a circulating fluid during workover operations. It is evident from the field behavior cited that the productivities of certain oil- and gas-bearing formations have been damaged by exposure to drilling muds. This reduction in well productivity, called "formation damage", causes serious consequences. In development wells, expensive remedial operations are incurred. In wildcat wells, good formations may appear to be marginal or even non-productive. The importance of formation damage has been recognized by a number of investigators1-s who have considered the effects of fresh water, saline solutions and aqueous mud filtrates on the permeabilities of formations. A general conclusion from such studies is that interaction between water and formation clays reduces permeability of reservoir rock and that the permeability decreases as salinity of the water decreases. Data in these references, however, concern the permeability change with only a single fluid present. A more pertinent and direct consideration in the production of oil and gas from wells is the permeability change when two fluids, oil and water, are present. Recognizing this, Nowak and Kreuger2 and Bertness1" considered several ways in which mud filtrates and saline solutions caused reductions in the oil permeability of formation cores. Investigations discussed here were designed to supplement information in the literature on changes in oil

By Roland de Wit

Conclusions reached in a paper by weertmanl are amplified in a mathematical and graphical way. It is shown that in a stressed crystal a straight dis-location may be in a position of unstable equilibrium with respect to helix development, and how a small perturbation may start the dislocation off on its helical path. Helix development occurs by diffision; bulk diffusion is necessary for development from a screw, but core diffision is sufficient for development from an edge dislocation. For a mixed dislocation helix development can take place by core diffusion if the helix also climbs; a diffusion reversal takes place when the slope of the helix equals the slope of the Burgers vector. The work done on a crystal by the external forces is graphically shown to be consistent with the direction of motion of the dislocation in helix development. Finally a detailed mechanism for tangle formation from helices is presented. In the course of helix development a glide situation may be reached where a segment of each helix loop lies in a slip plane in which it can expand by glide. Thus is it visualized how a helix can deteriorate into a tangle. A paper by weertmanl proposes dislocation-tangle formation by a helical dislocation mechanism. The present paper amplifies Weertman&apos;s arguments in a mathematical and graphical way and presents some further ramifications of the proposed model. The importance of dislocation tangles is discussed in Weertman&apos;s paper and the references cited therein. The mechanism of their formation is not yet understood. Weertman proposes that in cold-worked crystals conditions exist suitable for the conversion of straight dislocations into helices and subsequently into tangles. Helix formation occurs by a diffusion process and Weertman proposes that at low temperatures only core diffusion is important. The present paper necessarily repeats some of Weertman&apos;s work. Since the mathematical development and notation used are slightly different from his, this was thought necessary for clarity. GEOMETRY OF THE HELIX weertman2 has shown that the equilibrium form of any dislocation line is a helix if it is assumed that the energy per unit length (line tension) of the dis- location is constant. For the special case that no external forces act on the dislocation, the helix reduces to a straight line. We shall assume in this paper that the dislocation has a helical form even when it is not in equilibrium. The parametric equation of a helix is, see Fig. l: where a is the radius of the cylinder tangent to the helix, and 270 the pitch of the helix. The pitch is related to v, the number of turns per unit length (along the axis) by the relation: When a = 0 Eq. [I] gives a straight line in the z direction. The growth of a straight dislocation into a helix is now described mathematically by letting a vary from zero to its final value. The tangent to the helix is given by where is the path length along the helix. This gives the direction of t and since its magnitude is unity we must have So that dcp/ds = (a2 +p2)-"&apos;. The curvature of the helix is given by where n = -(cos + sin) is a unit vector normal to the helix. Note that the vectors k and n always point toward the axis of the helix, Fig. 1. FORCE ON THE HELIX The external force which makes the straight dis-

Jan 1, 1963

To Americans, Alaska occupies a unique position, both geographically and historically. The only integral portion of the United States lying in the sub-Arctic and Arctic regions of the Earth, the early remoteness and climatic conditions effectively combined to impede the economic development of this area. Although Alaska has been a part of our Nation since 1867, its mining industry is still at that stage of development which characterized the West 100 years ago when miners concentrated on high-grade lodes and rich placer deposits. Since World War II, however, there has been a noticeable increase of interest in the raw materials of the North. This concern has been most noticeable in Canada, Scandinavia and Russia, but it has been, and is being shown in Alaska. To the American mining industry, the potential importance of this State can be summed up by the question, "Can Alaskan mining compete successfully with those of other states and countries?" The answer revolves about the vital factors of geography, economics, and the political turmoil of the World. These aspects are among those discussed on the following pages in a series of articles by Alaskans and non-Alaskans alike. We invite you to read "Alaska: Regional Report."

Jan 12, 1961

By A. H. Geisler, R. F. Mehl, S. Barrett

The studies of the mechanism of pre= cipitation and of the resulting property changes in aluminum-silver alloysl-3 have presented some new concepts of the aging reactioxl—concepts that may be fundamental in establishing a complete quantitative theory of age-hardening. With both aluminum-copper and aluminum-silver alloys, thin platelike aggregates form parallel to the Widmanstätten planes of precipitation.l,4 These platelets grow in lateral dimensions and in thickness with aging time until they arc thick enough to produce an X-ray diffraction line pattern. Their structure is that of a transition lattice which is coherent with the matrix, since the atomic spacings in the matrix and the precipitate are the same on each side of their common interface.2,4 The equilibrium precipitate forms later from and at the expense of the transition lattice. Since age-hardening occurs during the formation and growth of the transition lattice, the major contributor to the hardening no doubt is the stress condition in the matrix resulting from the matrix holding the precipitate in the coherent condition. The development of these stresses also appears to be responsible for an increase in the electrical resistance superimposed on the normal decrease resulting from a change in the concentration of the matrix during aging.3 The two consecutive reactions constituting the aging process are accompanied by characteristic microstructural alterations. The initial precipitation process results in the formation of a Widmanstatten figure, while the later transformation of the transition lattice to the equilibrium lattice is accompanied by a coalescence, in the case of aluminum-copper alloys,5 and by the appearance of light areas at the grain boundaries with aluminum-silver alloys showing a structural rearrangement of matrix and precipitate.3 This latter reaction is similar microscopically to the so-called "discontinuoils precipitation." Possibly discontinuous precipitation is a process that often if not always follows true precipitation of a coherent lattice and during which the transformation of the coherent transition lattice to the equilibrium lattice takes place accompanied by matrix recrystallization.3 Expermental Procedure The alloys were made using 99.97 per cent A1 or distilled magnesium, with

Jan 1, 1943

By R. F. Mehl, A. H. Geisler, S. Barrett

The studies of the mechanism of pre= cipitation and of the resulting property changes in aluminum-silver alloysl-3 have presented some new concepts of the aging reactioxl—concepts that may be fundamental in establishing a complete quantitative theory of age-hardening. With both aluminum-copper and aluminum-silver alloys, thin platelike aggregates form parallel to the Widmanstätten planes of precipitation.l,4 These platelets grow in lateral dimensions and in thickness with aging time until they arc thick enough to produce an X-ray diffraction line pattern. Their structure is that of a transition lattice which is coherent with the matrix, since the atomic spacings in the matrix and the precipitate are the same on each side of their common interface.2,4 The equilibrium precipitate forms later from and at the expense of the transition lattice. Since age-hardening occurs during the formation and growth of the transition lattice, the major contributor to the hardening no doubt is the stress condition in the matrix resulting from the matrix holding the precipitate in the coherent condition. The development of these stresses also appears to be responsible for an increase in the electrical resistance superimposed on the normal decrease resulting from a change in the concentration of the matrix during aging.3 The two consecutive reactions constituting the aging process are accompanied by characteristic microstructural alterations. The initial precipitation process results in the formation of a Widmanstatten figure, while the later transformation of the transition lattice to the equilibrium lattice is accompanied by a coalescence, in the case of aluminum-copper alloys,5 and by the appearance of light areas at the grain boundaries with aluminum-silver alloys showing a structural rearrangement of matrix and precipitate.3 This latter reaction is similar microscopically to the so-called "discontinuoils precipitation." Possibly discontinuous precipitation is a process that often if not always follows true precipitation of a coherent lattice and during which the transformation of the coherent transition lattice to the equilibrium lattice takes place accompanied by matrix recrystallization.3 Expermental Procedure The alloys were made using 99.97 per cent A1 or distilled magnesium, with

Jan 1, 1943

By David H. Browne

The trite maxim that man is a tool-using animal might nowa-days be amended by saying that man is a tool-choosing animal. The chipped flint, at first all-sufficient, gave way to hammered bronze, and that, in turn, to wrought-iron and steel. As our knowledge of metals increases, we learn to specialize; we temper and anneal; we alloy and intermix; and we fashion for ourselves a metal suitable to our necessities. The knowledge of the properties and uses of the various metals and their alloys has become the capital of every constructive engineer, and the currency of every intelligent brass-founder aid blacksmith. Prom year to year, the specifications of the designer become more rigid, and the steel-maker is forced to study more closely the qualities obtainable by changing the treatment, or altering the composition, of his metal. Of making alloys there is no end. We have heard much, during the last decade, of manganese-steel and chrome-steel, of aluminum and tungsten, of titanium- and silicon- and copper-steels, and of every conceivable union into which steel could be coerced or cajoled. Without denying to each of these alloys novel and valuable properties, it. must be admitted that, of all alloys, the one which shows the greatest range of adaptability, and has met the largest measure of popular approval, is nickel-steel. Introduced to public notice by Mr. Riley, in 1889, its field of usefulness has been rapidly enlarged, until, at the present day, the use of nickel-steel is as thoroughly recognized as that of carbon- or manganese-steel. Concerning the properties of nickel-steel numerous articles have appeared in the technical journals. For the man in a hurry, who wishes to look up the properties and limitations of nickel-steel, these articles might almost as well be in the lost

Jan 1, 1900

By AIME AIME

The following changes of address of members have been received at the Secretary&apos;s office during the period of Mar. 1 to May 1, 1908. This list, together with the list in Bi-Monthly Bulletin, No. 20, March, 1908, therefore, supplements the annual list of members corrected to Jan. 1, 1908, and brings it up to the date of May 1, 1908. The names of Members who have accepted election during March and April, 1908 (new members), are printed in italics., By a simple method of cutting out these names and addresses, and pasting them directly over the corresponding names in the annual list of members, the record can be kept practically up to date and the value of the list correspondingly increased. For this purpose the changes of address have been printed only on one side of the page. The names of new members, being in italics, are readily distinguished from the others, and can be pasted in approximate alphabetical order on the margins of the pages of the list.

Jan 5, 1908

By W. C. Maurer

A study of bit-tooth penetration, or crater forniation. under simulated borehole condirions has been made. Pressure conditions existing when drilling with air, water and mud have been sirnulated for depths of 0 to 20.000 ft. These crater tests showed that a threshold bit-tooth force must he exceeded before a crater is .formed. This thresh old force increased with both tooth dullness and diflerenrial pressure between the borehole and formalion fluids. At low differential pressures, the craters formed in a brittle manner and the cuttings were easily removed. At high differenlial pressures, the cunings were firmly held in the craters and the craters were formed by a pseudoplas-tic mechanism. With constant farce of 6,500 16 applied to the bit reeth, an increase in differential pressure (sitnulated mud drilling) from 0 to 5,000 psi reduced the crater volumes by 90 per cent. A comparable increase in hydrostatic fluid pressure (simulated water drilling) produced only a 50 per cent decrease in volutne while changes in overburden pressure (simulated air drilling) had no detectable effect on crater volume. Crater tests in unconsolidated sand subjected to differential pressure showed that high friction was present in the sand at high pressures. Similar friction belween the cuttings in craters produces the transition from brittle to pseudo plastic craters. INTRODUCTION The number of wells drilled below 15,000 ft increased from 5 in 1950 to 308 in 1964. Associated with these deep wells are low drilling rates and high costs. High bottom-hole pressures produce low drilling rates by increasing rock strength and by creating bottom-hole cleaning problems. This paper describes an experimental investigation of crater formation under bottom-hole conditions simulating air, water and mud drilling. Although numerous investigators have studied bit-tooth penetration (cratering) at atmospheric pressure conditions, only limited work has been done on cratering in rocks subjected to pressures existing in oil wells. Payne and Chippendale2 have studied cratering in rocks subjected to hydrostatic pressure using spherical penetrators. Garner et aLJ conducted crater tests in dry limestone by varying overburden pressure and borehole fluid pressure independently and using atmospheric formation-fluid pressure Gnirk and Cheathem4,5 have studied crater formation in several dry rocks subjected to equal overburden and borehole pressure and atmospheric formotion pressure. Podio and Gray studied the effect of pore fluid viscosity on crater formation using atmospheric borehole and formation-fluid pressurc and varying overburden pressure. Although these studies have provided useful information on crater formation under pressure, they were limited in that the three bottom-hole pressures could not be varied independently and, therefore, that many drilling conditions could not be simulated. The prersure chamber used in this study allowed visual observation of the cratering mechanism and independent control of the borehole, formation and confining pressures. By using different fluids in the chamber, pressure conditions existing in air, water and mud drilling to depths of 20,000 ft were simulated. The mechanisms involved in cratering at these different pressure conditions were studied for teeth of varying dullness and at different loadins rates. High-speed movies (8,000 frames/sec) and closed-circuit television were used to visually study the crater mechanism under pressure. EXPERIMENTAT PROCEDURE PRESSURE CHAMBER The Pressure chamber in Fig. I was used to simulate bottom-hole pressure conditions. This chamber has been pressure-tested to 22,500 psi and is normally operated at pressures up to 15,000 psi. The chamber contains four lucite windows&apos; used for illuminating and observing the crater mechanism under pressurc. A closed-circuit television and a Fastax camera (8,000 frames/sec) have been used in these studies. Cylindrical rock specimens (8-in. diameter X 6-in. long) were subjected to three independently controlled pressures simulating overburden, borehole fluid and formation-fluid pressures. Overburden pressure, which corresponds to the stress induced by the overlying earth mass, was applied by exerting fluid pressure against a rubber sleeve surrounding the rock. Borehole pressure, which is the pressure exerted by the column of mud in the wellbore, was simulated by applying pressure to the fluid overlying the rock in the chamber. Formation pressure was simulated by applying pressure to the water saturating the rock. The borehole and formation pressures were equal except when mud was used in the chamber, in which case the differential pressure between these fluids acted across the mud filter cake.

Jan 1, 1966

By D. M. Milne, R. F. Stoner, W. Bakiewicz

The Lower Indus Basin deposits form a substantial unconfined alluvial aquifer of excellent quality. This aquifer contains basically highly saline groundwater, overlain in places by considerable amounts of fresh water whose origin can be traced to the present and historical courses of the River Indus. In the past, the main source of groundwater recharge has been direct river seepage and water tables were generally deep. Since the establishment of a perennial irrigation regime however, deep percolation from the increased irrigation supplies has predominated and the water table has risen to within a few feet of the surface. The river system itself is being progressively devel-oped for irrigation and very shortly a situation will arise where the entire low winter flow will be utilized. Fresh groundwater will then be exploited to supplement the surface supplies, and at the same time a drainage system, mainly based on wells will be used to stabilize the water table at safe depths. This paper discusses some of the methods used to ensure optimum economic development of the fresh groundwater and describes the general design philosophy evolved by the authors&apos; firms for both irrigation and drainage wells, with respect to both well configuration and operation. Water quality standards are discussed insofar as they affect subsequent use of the groundwater. A few particular aspects are considered, including the values of the relevant aquifer constants, the construction of wells, and the determination of screen losses. A major problem solved during the Lower Indus Project investigations has been the design of wells to produce fresh water from layers overlying saline water. This solution is also discussed. The recent interest in the groundwater of the Lower Indus Plains of West Pakistan has two main aspects. Firstly, soil waterlogging and the associated salinity hazards caused by rising water tables are a serious problem in agriculture, and the ease with which drainage requirements can be met by aquifer pumping makes this an obvious solution. The second interest stems from the rapid intensification of irrigation agriculture and the growing shortage of water supplies. In the areas where the groundwater is of suitable quality it can be used immediately for irrigation at relatively small cost and with large financial returns. In addition, the aquifer forms a potential storage reservoir which could be recharged from high river flows and depleted by pumping at times of scarcity. SOURCE OF GROUNDWATER The Lower Indus plain is a relatively long and narrow alluvial basin on a north-south axis, some 23,000 sq miles in area, bounded by higher land to the east and west. One hypothesis to explain the distribution and quality of groundwater in the region1 presupposes a river system considerably larger than, but very similar to the present river. This is characterized by a single mainstream, with subsidiary overspill channels in times of flood, running along the crest of a self-deposited ridge and with an extensive advancing delta. Sea water is contained in the alluvial pores of the advancing delta, forming the native groundwater. This has been partially displaced from two sources, namely direct seepage of fresh water from the river channel in meander flood plain areas and percolation from flood spillage in cover flood plain areas. Percolation has been subject to much re-evaporation and is thus slightly saline even as it reaches the groundwater. The whole complex has been further affected by two main influences: evapotranspiration from the land surface that tends to salinize the groundwater and down-valley flow that tends to bring fresher water

Jan 1, 1970

By W. H. Bassett

Beads of metal frequently appear at the ends of cast-copper wire bars and on the sides of wedge cakes near the top. These are richer in cuprous-oxide than the rest of the casting. A micrographical study of these exudations has been made. It is suggested that the material is forced through the surface while the copper is solidifying. If not eliminated in process of manufacture, it shows on the finished polished sheet copper in patches differing in color from the main body of the sheet. FIGURES 1 to 4 show the copper exudations, at different magnifications, as they appear on the ends of cast wire bars, and on the sides, usually near the top, of wedge cakes. Sometimes the exudations are in fine "drops;" at other times, large masses of the material are found. Microscopic examination of the copper exudation indicates that it is high in oxide and of eutectic proportions. Because of the difficulty of securing a suitable sample, the protuberances have not been analyzed chemically; but the spectroscope shows no indication that there are any more metallic impurities present than in the balance of the copper. The lowest copper plus silver content of the coppers studied for this? paper was 99.914 per cent.; the highest, 99.966 per cent.; so the oxygen content of the whole casting would be well under 0.07 per cent.

Jan 2, 1926

By E. T. Turkdogan

This paper deals with an analysis of the conditions leading to the formation of blowholes and surface and subsurface defects in cast low-carbon steels. The theoretical analysis of the problem is based on the concept of the occurrence of deoxidation reactions during cooling of liquid steel and during its solidification. The reaction equilibrium data are given on deoxidation of steel by carbon, silicon, and manganese. The details of the calculations are given on the simultaneous deoxidation of steel by silico-manganese additions to produce a desired level of deoxidation at certain residual concentrations. Based on an idealized model, an attempt is made to calculate the enrichment of solutes in the solidifying liquid entrapped within the interdendritic cells which are known to be less than 200 µ thick. Formulae are derived for the calculation of the change in the residual oxygen content of the enriched liquid steel, controlled by Si/Mn deoxidation. It is shown that for every particular initial silicon, manganese, and oxygen concentration in steel (as residuals in liquid solution at the beginning of solidification) there is a particular carbon concentration below which carbon monoxide, leading to blowholes or pinholes, is not expected to form. There are a number of independent variables which have a decisive influence on the formation of blowholes. For example, it is shown that the position of the curve depicting the critical relation between initial silicon and carbon content for suppression of the evolution of carbon monoxide) can be shifted to lower silicon or higher carbon levels by: increasing manganese content; decreasing oxygen, hydrogen, or nitrogen content; or increasing external pressure on the solidifying mass. FOR the production of sound castings it is essential to prevent the formation of interdendritic worm-holes or pinholes brought about by gas evolution during solidification. Another major problem encountered in solidification of ingots is the formation of surface defects. These problems are thought to be closely associated with the deoxidation reaction occurring in liquid steel during cooling and subsequent solidification. As the liquid becomes richer in impurities during dendritic solidification of steel, a series of reactions may occur in the liquid phase trapped within the branches of growing dendrite platelets. Because of the strong interaction between dissolved oxygen and impurities in liquid steel, the reactions most likely to occur are of the deoxidation type. However, inherent to the extreme complexity of the problem in question, numerous simplifying assump-

Jan 1, 1965

By Andrew Cosgarea, William R. Upthegrove, Morteza Mirshamsi

The capillary-reservoir technique was used with lead-210 and cadmium-115m to determine the self-diffiLsion coefficients of both cadmium and lead in the liquid binary Cd-Pb system. The self-diffusion coefficients of pure cadmium and pure lead were obtained and were compared with the theoretical predictions. Good to excellent agrement between the experimental and predicted values was obtained. The self-diffusion coefficients of cadmium were tneasuved in alloys containing 2.50, 9.13, 17.40, 31.00, 45.00, 69.00, and 97.00 lot pct Cd by determining- the amount of cadniiutn-115m which diffused out of a small-bore capillavy into an infinite reservoir during- a given time peviod. Sinzila7-measurements were made with lead-210 to determine the self-diffusion coefficients of lead in these identical alloys. Diffusivities were determined from measurenzents performed in the temperature interval of 290" to 480°C. The results were correlated with the Ar-vhenius equation, and the maximum variation of the equation parameters (Q and Do) was also inrestigated . THE theory of diffusion in liquids, particularly liquid metals, is relatively undeveloped in contrast to that for the gaseous and solid states. Although the practical application of liquid metals as heat-transfer media has become increasingly important, few liquid-metals systems have been investigated. Experimental data of fundamental significance in this field are not readily obtained, which may explain but not justify the present lack of knowledge. What work has been completed is primarily restricted to liquid diffusion of pure metals; little work has been done in liquid-metal diffusion of binary mixtures. A review of liquid-metal diffusion theory and research is available elsewhere.1-4 In an effort to add to the knowledge of liquid-metal systems and to increase the basic understanding of the diffusion process in liquids, a study of diffusion in the binary-liquid system, Cd-Pb, was undertaken. The capillary-reservoir technique5 was employed to measure the self-diffusion coefficients of cadmium and lead in molten binary alloys. Measurements were made with seven selected compositions and over a temperature range from 290° to 480°C. The experimental apparatus consisted essentially of the following items: constant-temperature bath, diffusion cells, capillaries, capillary-filling device, and a radioactive tracer counting system. EXPERIMENTAL APPARATUS Constant-Temperature Bath. A cylindrical steel vessel, 8 in. in diam and 15 in. deep, surrounded by an insulated heating coil was used with a sodium-potassium nitrate salt mixture heating medium. The bath was maintained slightly below the desired control temperature by the furnace-heating element; and a 250-w heater, actuated by a Bayley proportional temperature controller, was utilized for the final control of the temperature. A constant-speed mixer stirred the salt to insure a uniform temperature within the bath. Four calibrated Chromel-Alumel thermocouples were placed at various positions in the salt bath to verify the absence of temperature gradients. The observed temperature variation during any diffusion run was less than 0.l°C. The entire furnace assembly was mounted on four shock absorbers to exclude building vibrations and the stirrer propeller blades were adjusted so not to induce vibrations within the reservoir. A schematic diagram of the furnace and the constant-temperature bath is shown in Fig. 1. Diffusion Cell. The diffusion cells and associated parts were the same, except for slight modification, as the one used by walls1 in this laboratory, and are shown in detail elsewhere.&apos; A graphite crucible, 4 in. long and 40 mm (1-1/2 in.) ID, enclosed in a 60-mm (2-1/4 in.) Pyrex tube cell about 18 in. long, was used as a container for the melt. The reservoir (molten alloy in the graphite crucible) was usually about 2 to 2-1/2 in. deep. Graphite was used because of its satisfactory nature as a refractory material and the low solubility of carbon in molten Cd-Pb alloy.677 The Pyrex cell was closed at the bottom and fitted at the top (open end) with a 2-in. Dresser coupling. A brass flange was welded to the top of the coupling. The upper part of the diffusion assembly was bolted to this flange with an O-ring seal. The lower part of the diffusion cell was supported in a 3-in. brass cylinder which was open to allow for circulation of salt around the cell. The top assembly consisted of two synchronous motors, a drive shaft, a thermocouple well, and controlled-atmosphere inlets and outlets. One motor was used for rotation of the capillaries at a rate of 1/2 rpm in the reservoir during the diffusion run. The other motor was used for the vertical positioning of the capillaries and the capillary holder by means of a simple screw drive. The capillary holder and drive assembly were lowered into the reservoir for the run and raised after the desired diffusion time at a rate of approximately 0.4 in. per min. Capillary holders were made of graphite. These

Jan 1, 1967

By H. A. Kendall, W. C. Goins

Several investigations in recent years have shown that drilling rates are increased significantly with increased hydraulic horsepower. But, there has been no over-all method of designing jet-bit programs that efficiently uses the surface power. A study of present practices indicates that frequently as little as 50 per cent of the possible effects at the bit are used. Some observers have indicated that the best utilization of hydraulic horsepower (maximum effect on drilling rate) occurs when the bit hydraulic horsepower is maximum; others have stated that jet impact force is more important, and others have believed that maximum jet velocity is required. Limited efforts to date have shown some optimum conditions for bit hydraulic horsepower and impact, but these conditions cannot exist during drilling of a large part of the hole and do not provide a basis for designing a complete jet-bit program. This paper shows the maximum obtainable bit horsepower, impact force and jet velocity at all depths, taking into account the limitations of the pump, piping, hole and minimum circulating rate for adequate cuttings removal. Ranges of operation are developed; and flow rates, surface pressure and bit pressures are specified for each range to provide a maximum of any one of the desired effects. It also is shown that, by proper selection of nozzle sizes and by following the rules presented, the maximum obtainable quantities can be effectively utilized from surface to total depth. Finally, a simple graphical method of selecting nozzle sizes and flow rates is presented which can be used with familiar bit-company hydraulic tables and calculators to design jet-bit programs for maximum bit hydraulic horsepower, impact or jet velocity, as desired. These programs make most effective use of the pumps. Heretofore, there was no method available for designing field tests which adequately separated the effects of bit horsepower, impact and jet velocity. The programs and procedures developed in the paper are dissimilar and, when used in future field testing, should demonstrate which program is the most important in obtaining the fastest drilling rate. INTRODUCTION During the past decade, rig hydraulics has come into increasing prominence. There has been a definite trend toward providing higher horsepower pumps, jet-type bits have had increased use, numerous investigators"" have reported increased drilling rates as a result of increased hydraulics, and bit manufacturers have provided tablesa-" and calculators that are now commonly used 10 design jet-bit programs. Opinion has varied as to the hydraulic quantity which has the great- est effect on drilling rate. Papers and data have been presented that show pump horsepower,&apos;9 it hydraulic horsepower and jet impact force,&apos; each to be the most significant factor affecting drilling rate. Examinatibn of jet-bit programs of the bit companies indicates emphasis on jet velocity. Only pump horsepower can be eliminated because it can be used to produce any one of the bit effects which, a priori, must be more relevant factors. This contradictory state of opinion and practice regarding the bit effects is unfortunate, but several published references have been concerned with making one or another of the factors maximum; and, because these in each case have given results applicable to only intervals of the hole drilled, there seems to be ample reason to complete the previous efforts. It also is believed that the differences in programs for each effect, where they exist, should be delineated so that future use may determine which hydraulic effect is the more relevant. It is the purpose of this paper to: (1) show the theoretical maximum bit hydraulic horsepower, jet impact force and jet velocity available at all depths, taking into consideration all necessary restrictions on operating conditions; (2) illustrate procedures by which the maximum available horsepower, impact force or veIocity may be obtained; and (3) present a graphical method for rapid selection of jet-nozzle sizes and flow rates to be used with conventional procedures to design jet-bit programs for maximum bit horsepower, impact force or velocity as desired.