Search Documents

By P. M. Aziz, I. Markson, C. S. Barrett

The abnormal after-effect in twisted wires that occurs when untwisting is interrupted by etching con be brought under control and used to study the mechanical properties of thin surface films and how they are effected by reagents and heat treatment. Results are given of studies of oxide films on high purity aluminum. IF a wire is subjected to plastic deformation by torsion and then released, it untwists in the normal after-effect, but under certain circumstances the untwisting is abruptly lessened or reversed by the application of an etchant to the wire.1,2 This abnormal after-effect may occur, for example, if there is a coherent oxide film on the surface of the wire which is removed by the etchant. Following a suggestion of A. H. Cottrell that predicted this effect, it is attributed to dislocations that had piled up beneath the oxide layer and represents the rapid release of residual stresses caused by these dislocations. When the layer is removed, the stress relief may be by escape of piled-up dislocations from the metal, or by an activation of latent sources of dislocations located at the surface, together with rebalancing of elastic stresses to compensate for the loss of stressed material, as in a residual stress analysis determination, these mechanisms acting singly or in combination.' The slower the attack of the reagent, the more gradual is the stress relief and the smaller the change in strain rate when the reagent is applied. A study has been made of the factors that influence the magnitude of the normal and abnormal after-effects with the object of developing techniques suitable for a quantitative investigation of the influence of various surface films on dislocations in wires, and of the rate and extent of the attack on the films by different reagents. It was found that reasonable sensitivity and reproducibility could be achieved if a suitable choice of variables was made and if these variables were held constant through a series of experiments. The method was then applied to a study of oxide films produced and treated in different ways on the surface of high purity aluminum wires, and to a study of the damage to these films caused by various reagents. Experimental Procedure The material used throughout this work was prepared from 99.9968 pct Al. This high purity aluminum was melted, cast into 1/2 in. diameter ingots, and then swaged and drawn without intermediate annealing to 0.040 in. diameter wire. A sketch of the apparatus employed for twisting is shown in Fig. 1. The test wires were mounted into the apparatus by cementing one end of the wire to the beaker and the other to the tube with laboratory wax of high melting point. The length of the wire between the waxed joints was 4.2 & 0.2 cm. Extreme care was taken during mounting to avoid cold-working the wire. The wire was twisted through 335" in 2 to 4 sec by rotating the pinion on the gear box until the vertical post on the rotating table, which was initially touching the horizontal stop, was arrested by the stop. All the tests were conducted with apparatus and reagents at the same temperature (about 25°C). In all tests, except those where the duration of the initial torque was investigated, the torque was applied for a period of 2 min. At the end of this time the table was rotated back a few degrees away from contact with the stop and the wire allowed to untwist. The after-effects were measured by reflecting a beam of light from the mirror shown on the apparatus. After the wire had untwisted for 6 min, a reagent was carefully poured into the beaker and thereby applied to the surface of the wire.. In some tests the liquid in the beaker was removed after a few minutes and replaced by an-

Jan 1, 1954

By F. L. Robertson, C. H. Bacon, J. W. Till

A description is given of the development of a process for making low sulphur steel on furnaces fired with 2 1/2 pet sulphur oil. Slag and metal are analyzed at melt. Slag weight is estimated. A simple method for calculating necessary lime additions for making 0.025 and 0.035 pct sulphur steel is given. DURING the last 15 years John Summers & Sons have been confronted increasingly by the problem of producing a low sulphur steel from high sulphur materials. The principles adopted, the processes used, the data collected on a furnace specially set aside to study this problem, and speculation on future developments are dealt with in this paper. This study is limited to two melting shops which make sheet steel only, of the following analysis: C, 0.06 pct; Mn, 0.33; S, 0.04, 0.035, 0.03, and 0.025; and P, 0.02 and 0.015. All the processes described have reference to the manufacturing of this steel and are not necessarily applicable, without modification, to other steels. The raw materials used are given in Table I. Development of Process About 1934, Schenck's work on phosphorus was applied to frame quantitative rules for the removal of phosphorus, with great success. We could however, neither in our own work nor in the voluminous literature, find any assistance to frame quantitative furnace rules to remove sulphur. Perhaps, we should have persevered with Schenck's outstanding chapter on sulphur in The Physical Chemistry of Steelmaking, but we missed the importance of one (Ss) sentence on p. 478. "Evidently this ratio -------- is [S] the important quantity to be considered from the point of view of chemical reaction; it is clear that the sulphur content of the steel alone, as frequently given in the literature cannot suffice for judging the success of the reaction unless special details are given regarding the sulphur charge and the amount of slag."' We were not however very successful in getting values for Schenck's "n" that agreed with (S) arrived at by our direct analysis. [S] In addition to Schenck's work much attention was given to V value. The formula selected for V was: (SCaO) — 1.57 (2 P2O5) (S SiO2) After plotting many charges a curve was obtained, based upon the relationship between the percentage sulphur in the finished steel and V value, Fig. 1. For a long time this was used as standard with about a 60 to 70 pct success on producer-gas fired furnaces, if all uprising scrap was used and no bought scrap used. An inspection of this curve shows clearly that it is not a quantitative manufacturing process, and that it was not sure enough to go to the trouble and expense of doing stage analysis for P,O,,

Jan 1, 1952

By Arthur C. Simmons

Production of oil within the state of Pennsylvania in 1940 was slightly more than the 1939 total, and this increase was due entirely to the new flush Music Mountain field south and west of the main Bradford pool. The influence and magnitude of Music Mountain production will be separately described, inasmuch as it is an important producing unit within the state. Production Bradford Field The production listed herein for Bradford field includes only the part of the field that is within the state of Pennsylvania. Approximately 4000 bbl. per day, or 10 per cent of the total Production of Bradford field comes from Cattaraugus County, New York, and should properly be attributed to production obtained within the New York state area, although locally and economically the Bradford field, situated both in New York State and Pennsylvania, is included as a single statistical unit. The 1940 average production in the Bradford field was 34,831 bbl. per day, as compared with a daily average in 1939 of 35,340 bbl., or a decrease from 1939 of 509 bbl. per day. The decrease in production from the Pennsylvania portion of the Bradford field would have been more pronounced if a portion of the crude from the Music Mountain field were not included with the statistics for Bradford field. The decline can be attributed largely to the fact that more properties of lower average recovery were being drilled in 1939 and 1940 than in previous years, and apparently a subnormal amount of drilling occurred in 1938 and 1939, when about 2100 wells were drilled each year. The full effect of the 1940 drilling is not felt immediately and undoubtedly will affect the producing period of 1941. It appears probable that the water-flood area in the Bradford field has reached a definite peak unless some unusual economic condition should cause abnormal prices and an excessive rate of development such as occurred in 1936 and 1937. Virtually all of the production in the Bradford field was obtained by water-flooding methods, as natural or stripper wells are uneconomical and air and gas repressuring have not proved so efficient as water-flooding as a secondary recovery method. Central and Southern Pennsylvania Central and southern Pennsylvania produced a total of 4,604,763 bbl. of oil during the calendar year of 1940; that is, an increase over the 1939 total of 166,728 bbl. The daily average production was 12,581 bbl., or an increase over 1939 of 422 bbl. per day. Table I includes the total oil production for the state of Pennsylvania for the years 1937 to 1940, inclusive, and the daily average for each of these years. It is impractical to make a complete subdivision by districts, consequently the only segregation is the production from the Bradford field (within the state of Penn-

Jan 1, 1941

By Arthur C. Simmons

Production of oil within the state of Pennsylvania in 1940 was slightly more than the 1939 total, and this increase was due entirely to the new flush Music Mountain field south and west of the main Bradford pool. The influence and magnitude of Music Mountain production will be separately described, inasmuch as it is an important producing unit within the state. Production Bradford Field The production listed herein for Bradford field includes only the part of the field that is within the state of Pennsylvania. Approximately 4000 bbl. per day, or 10 per cent of the total Production of Bradford field comes from Cattaraugus County, New York, and should properly be attributed to production obtained within the New York state area, although locally and economically the Bradford field, situated both in New York State and Pennsylvania, is included as a single statistical unit. The 1940 average production in the Bradford field was 34,831 bbl. per day, as compared with a daily average in 1939 of 35,340 bbl., or a decrease from 1939 of 509 bbl. per day. The decrease in production from the Pennsylvania portion of the Bradford field would have been more pronounced if a portion of the crude from the Music Mountain field were not included with the statistics for Bradford field. The decline can be attributed largely to the fact that more properties of lower average recovery were being drilled in 1939 and 1940 than in previous years, and apparently a subnormal amount of drilling occurred in 1938 and 1939, when about 2100 wells were drilled each year. The full effect of the 1940 drilling is not felt immediately and undoubtedly will affect the producing period of 1941. It appears probable that the water-flood area in the Bradford field has reached a definite peak unless some unusual economic condition should cause abnormal prices and an excessive rate of development such as occurred in 1936 and 1937. Virtually all of the production in the Bradford field was obtained by water-flooding methods, as natural or stripper wells are uneconomical and air and gas repressuring have not proved so efficient as water-flooding as a secondary recovery method. Central and Southern Pennsylvania Central and southern Pennsylvania produced a total of 4,604,763 bbl. of oil during the calendar year of 1940; that is, an increase over the 1939 total of 166,728 bbl. The daily average production was 12,581 bbl., or an increase over 1939 of 422 bbl. per day. Table I includes the total oil production for the state of Pennsylvania for the years 1937 to 1940, inclusive, and the daily average for each of these years. It is impractical to make a complete subdivision by districts, consequently the only segregation is the production from the Bradford field (within the state of Penn-

Jan 1, 1941

By P. K. Koh

Chi phase (body-centered cubic, a = 8.89A) was found in as-cast 23 pct Cr-10 pct Mo-Fe alloy as well as in heat-treated 316, 316L, 317, and modified 446 stainless steels. Chi phase resembles sigma phase in its metastability, chemical composition, and brittleness. Microstructure and some of physical properties of chi phase were developed. MOLYBDENUM has been established as a desirable alloying element for the enhancement of corrosion resistance in Cr-Ni steels and creep and rupture strength in high temperature alloys. On the debit side, however, the molybdenum addition has been known to stimulate u formation. When the molybdenum-bearing steels were subjected to prolonged heating at elevated temperatures, losses of corrosion resistance and/or ductility have been observed. Andrews1,2 first found the existence of a new phase among the anodic FeC13 extracts from type 316 stainless steel solution treated and then reheated from 800" to 1100°C. This phase was designated x and was identified by diffraction patterns as of body-centered cubic structure with a value equal to 8.89? and similar to that of a manganese. He found that the x phase in this steel always coexisted with s phase, but failed to distinguish one from the other by metallographic technique. No definite conclusion was drawn regarding the equilibrium temperature ranges of these two phases. The appearance of Andrew's work recalled an un- explained structure observed several years ago at the Allegheny Ludlum Research Laboratories during the investigation of an experimental alloy containing 25 pct Cr, 10 pct Mo, and balance Fe. X-ray diffraction patterns on the as-cast material revealed the presence of a body-centered cubic phase having a lattice parameter of 8.89?. The structure was sufficiently similar to that of y chromium that for a time it was thought that the structure might be caused by the presence of some undissolved electrolytic chromium particles. The alloy as-cast was so brittle that it shattered after the slightest hot reduction by hammer cogging. This paper gives the results of some metallographic and X-ray diffraction studies on x phase as found in several experimental alloys as well as a few molybdenum-bearing commercial stainless steels. The analyses of materials studied were as shown in Table I. Experimental Procedure Metallography: Solid specimens were polished mechanically and etched in boiling 50 pct HC1 solution in order to best delineate x and s phases in the alloys studied. X-Ray Diffraction: The difficulty of satisfactorily developing diffraction lines for s phase in solid specimens has been previously reported by Bindari, Koh, and Zmeskal.V or this reason all specimens used in this investigation were subjected to anodic

Jan 1, 1954

By G. L. Craig

In order to meet the unprecedented demand for copper it has proven necessary not only to develop every primary source, but also thoroughly to exploit the vast reservoir of metal in use that is not directly serving the war effort. To accomplish this, industry has been called upon to use its resourcefulness for developing methods of recovery that have not been previously utilized. It is in this connection that we have been asked to review the methods suggested for recovering the basic constituents of various types of the so-called clad or composite steels. As a background for a discussion of recovery processes, it seems appropriate to consider clad materials in general and their processes of manufacture. A composite steel has been defined as one consisting of two or more component parts of which the smallest shall comprise at least 3 per cent of the total mass. Clad materials or composites are produced commercially by several different methods of which the most important may be classified as: I. The Blacksmith or Forge Weld Method. This method is limited to carbon steels or low-alloy steels as the presence of even small amounts of common alloying metals prevent the formation of a satisfactory weld. The principle is the application of pressure to sections in contact at elevated temperatures. Because of the tendency of the iron to oxidize, borax is generally used as a flux to absorb the iron oxide. 2. Casting Process-In this method a composite ingot, billet or cake is produced by pouring one metal onto or about another. The bond may be accomplished by the action of the molten metal against a solid, in which case the bond may be referred to as mechanical; while in other instances alloying occurs at the interface producing an anchor by the formation of component parts of the two materials. 3. Cementation Process.-In this process any number of combinations of metallic and nonmetallic constituents which are mixed together may be used as a bonding agent. The combinations, whatever they may be, are placed between the materials to be joined and subjected to pressures at elevated temperatures to produce the desired bond. 4. Fusion Welding Processes.-Gas and electric joining for direct use or subsequent fabrication. 5. The, Assembly Process.-This method involves the joining together of prefabricated bars or plates followed by hot and/or cold working the assembly to the desired finished form. This method is advantageous in many cases because of its flexibility on small quantities as compared to the casting method. It is also possible to control the relative proportion of components more accurately. In this discussion we are concerned only with the scrap resulting from the manufacture of clad materials and our interest,

Jan 1, 1943

By J. Warner, M. J. Marcinkowski, B. Cullen, T. Prevender, J. Mcllwain, T. Carnahan, J. Pahlman, J. Demel, J. Munford

The following analysis was an outgrowth of a midterm examination given by one of the authors (M.J.M) in a course entitled Metallurgy 541 "Applications of Dislocation Theory'' at Iowa State University. Fig, l(a) shows the three-layer sequence of atoms lying in the (111) plane which characterizes the fully ordered AB3 fcc crystal, i.e., LI2 type. If any two-layer sequence of close-packed planes is constructed from Fig. 16)' the structure would be hcp of the DO,, type. Consider for convenience that the circled atoms lie in the plane of the drawing while those shown square and triangular lie immediately above and below the plane of the drawing, respectively. It has already been shown' that if a Shockley partial dislocation is passed over the plane of the paper, then the square atoms in Fig. 1(a) are displaced from their original positions as shown by the arrows in Fig. l(b). Not only is an intrinsic fault produced but the crystal is simultaneously disordered across the slip plane. In particular, 2AB bonds are converted to 1AA and 1BB bonds when referred to the area outlined by the solid line in Fig. 1. If, on the other hand, a Shockley partial is allowed to pass immediately above and immediately below the plane of the paper so as to displace the atoms in opposite directions as shown in Fig. l(c), an extrinsic fault is producedZ and twice the amount of disorder is introduced into the crystal as compared to the dislocation-produced intrinsic fault, if only broken first-neighbor bonds are counted. If an intrinsic stacking fault is produced by removing a close-packed plane of atoms in Fig. l(a) and displacing the two adjacent planes by 1/3a0[111], no wrong nearest-neighbor bonds are produced. Similarly, if an extra half plane of atoms with the same arrangement as any of those shown in Fig. l(a) is inserted between any two planes in the same figure, then an extrinsic stacking fault is produced in which once again no wrong nearest-neighbor bonds are produced. The latter two faults are bounded by Frank partial dislocations. Since, at least in the alloy CU3AU,3 nearly all of the ordering energy resides in the first nearest-neighbor interactions, intrinsic and extrinsic stacking faults and associated APB's of the Frank type are expected to have significantly lower energy than those of the Shockley type in CusAu in particular and quite likely in L1, and DO19 type alloys in general. Also, because of the higher degree of disorder plus loop interaction

Jan 1, 1968

By G. L. Hassler, E. Bruner

An apparatus and method is described whereby the relation between saturation and capillary pressure under decreasing saturation can be quickly determined for small core samples. The initially saturated core is cen-trifuged at increasing rates and the average saturation is measured at each rate with the aid of a stroboscope device. A theory and calculation procedure is given whereby the accelerations and saturation values can be converted into a true curve of capillary pressure versus saturation. The present work differs from previously described use of the centrifuge to obtain capillary-pressure curves of core samples3 in that the core is centrifuged alone, so that the whole range of saturations required by the properties of the sample and the radially varying centrifugal force occurs within the sample. The calculation procedure nevertheless secures correct results from simply obtained values of the average saturation. The apparatus described was developed in connection with studies of capillary pressure and wetting of oil-field rocks, and the paper provides the apparatus background for a previous publication' dealing more fully with the uses and implications of the data in petroleum engineering. The method is applicable, however, to general combinations of immiscible fluids and porous or comminuted solids, and may be useful in other fields. Introduction The importance of capillary phenomena in determining the behavior of liquids in porous media has long been recognized. The concept of capillary Pressure was early formulated, and in recent Years discussions of the application of the laws of capillarity to oil field problems have appeared.l-3 One reason why progress in the application of capillary phenomena to the solution of problems of reservoir mechanics has not been more rapid has been the lack of a, satisfactory technique for measuring the capillary pressures in reservoir rocks. It is the principal purpose of this paper to describe a method by which the relation between capillary pressure and saturation can be determined for small consolidated core samples which have been extracted and resaturated, Capillary Diaphragm Perhaps the most direct way to measure the capillary pressure in a rock is to make piezometric contact with the wetting liquid through a diaphragm of porous material with high displacement pressure saturated with the liquid in question.3-6 The liquid in the diaphragm assumes the pressure of the liquid in the core, which can then be measured with a manometer, while the atmospheric air is prevented by capillarity from entering the diaphragm and affecting the pressure measurements as long as the displacement pressure of the diaphragm is not exceeded. With an apparatus of the type illustrated schematically in Fig. I, the relation between capillary pressure and saturation can be measured for a small core sample by starting with the core saturated 100 per cent, applyillg successively greater suctions

Jan 1, 1945

By R. C. Thompson

The lead-zinc mill of Phelps Dodge Corporation, Copper Queen Branch, Mines Division, Bisbee, Arizona, is about 3 miles from the main hoisting shafts of the Junction and Campbell mines at Lowell. All the ore treated in the mill is obtained from these two mines. The mill was designed for an all-flotation treatment of 450 tons of lead-zinc ore per day, and has been operated at that capacity since the start of milling operations on Nov. 17, 1945. An expansion program is underway whereby the mill capacity will be doubled, but this article describes only the original program and presents results of the 450-ton operation. General Description The milling plant consists of an ore-receiving bin and three steel-constructed buildings housing, respectively, the primary crushing equipment, the secondary crushing equipment, and the ore-storage bins, grinding, flotation, and filtering equipment. The mill site is the one that was used for a previous copper-concentrating plant, which was operated over a period of years and then dismantled. There remained from this operation some milling equipment, a reservoir for mill-water supply, railroad tracks, tailings-disposal ponds, and a steel-constructed building, all of which were incorporated in the design of the present lead-zinc mill. The location plan of the plant layout is shown in Fig I. The flowsheet of the mill is based on the conventional scheme for lead-zinc treatment, however, several innovations were made necessary in order to utilize the existing building. Placing of equipment also was governed by the design of the building; thus making the mill unique in many respects. The following brief description of the mill building as adapted to the flowsheet points out the compactness of the installation and some of its unusual features. The first floor (Fig 2) houses the grinding equipment, with connecting conveyors for ore feeding, also an air compressor, two vacuum pumps, bins for lead and zinc concentrate storage with individual conveying systems for loading the two kinds of concentrates. Filtering of concentrates is done on the second floor, the concentrates discharging directly into the concentrate-storage bins. On this floor are the lead and zinc filters, two diaphragm pumps, sample-filtering equipment, sample-preparation room and a change room for the mill employees. The flotation machines are on the third floor, at elevations allowing a gravity flow of the lead and zinc concentrates to the thickeners. The annex to the building contains a freight elevator and provides space for all reagent mixing and feeding, also storage of reagents and grinding balls. All the water used for milling purposes is pumped from the Junction mine and

Jan 1, 1949

By Walter Miller

Hundred-octane aviation gasoiine, toluene for T.N.T. production, high-quality lubricating oils for the needs of aviation and the armed forces, and synthetic chemicals for rubber manufacture again commanded the top priorities of the petroleum refining industry in 1944, the third year of America's active participation in the war. The objective continued to be to produce more and more of these materials—to keep up with increasingly greater requirements. By the end of the year all of the new installations projected before 1944, with the exception of possibly two or three that will tail over into January or February of 1945, had been completed and put into operation. And with the completion and putting into operation of these various units and the consequent lessening of construction responsibilities and problems, the industry was put into position to concentrate on the new operations and devote much more of its time and effort looking toward maximum output, both as to quantity and quality from the new facilities. Aviation Gasoline Making high-octane aviation gasoline continued to be the prime requisite of refining activities during 1944 as it was in the two previous war years, with the sights at the end of the year set to still higher figures than those which had been previously projected. About July I the daily output had been raised to 400,000 bbl., with some few large plant installations still to be completed and put into operation. Indications were that by December production would be up to all requirements, with good inventories. However, although by the end of the year the industry was turning out something over 500,000 bbl. a day, the estimated requirements of the armed services had been raised by a considerable figure, owing to the greatly increased aerial activities both in the European and Far Eastern combat areas. By the end of the year, therefore, the picture had changed, with the prospect for a much longer continuation of the European war, so that even with the completion and putting into operation in the United States by January 1945 of the last two or three 100-octane units authorized prior to 1944, it was evident it would be necessary to make still greater efforts to increase output of existing facilities to keep safely ahead of the game. Efforts of the industry and the Petroleum Administration for War as well as the Technical Advisory Committee and other research and development groups are concentrated therefore on methods and means of further augmenting the produc. tion of all existing refinery facilities engaged in making 100-octane aviation gasoline and components entering into it. The goal will be reached.

Jan 1, 1945

By O. W. Bilharz

Acid mine-water drainage is a serious problem with many mines in the Tri-State zinc and lead mining district. Particularly is this true when large volumes must be considercd in unwatering old mines that have refilled with water which has dissolved the products of oxidation and has become chalybeate in character. The experiences discussed in this paper have to do specifically with the unwatering of a comparatively small area west of the town of Baxter Springs, Kans., where the pumping job was complicated by water of this type and where the extremely high sulphate content particularly effected that phase of mine drainage having to do with stream pollution. Location, Geology and History The Baxter Springs area of the Tri-State mining field is situated just west of the town of Baxter Springs and is a northeasterly extension of the main mineralized zones of the Oklahoma part of the district (Fig I). The mining area is traversed with well defined shear zones which provide easy circulation of ground waters and the ore bodies are found along these shear zones as localized enrichments wherever the structural conditions are favorable (Fig 2). The ore-bearing strata is Mississippian with an overlain capping of shale of Penn- sylvanian age. This shale strata carries much pyrite and marcasite at its base and undoubtedly was a contributing factor to the subsequent high iron content of the water. The area originally contained a sulphide water which discharged as an artesian flow in springs within the town and gave Baxter Springs its name. These springs were famed for many years for their mineral water. This original sulphide water was first removed about 1917 and active mining was carried on west of the town during subsequent high metal price periods. Many small mines were opened, with each localized enrichment becoming a separate mine. During the depression mining ceased and all mines in the west Baxter area were allowed to flood. No serious effort was made to again unwater until higher prices caused from the demand for metal for World War II once more focused attention 011 this part of the field. Original Mining Results in Oxidation As plans for unwatering progressed, it soon developed that the mine-water pools had become strongly acid in character and carried large amounts of sulphates in solution. This occurred in the following way. When the original sulphide water was removed, shafts sunk, and mining carried on over a number of years, ferrous sulphate was formed by the spontaneous oxidation of the pyrite beds in contact with air admitted through churn-drill holes and mine openillgs. These products of oxidation can be seen today in the old mines of the district as crusts of crystalline sulphates

Jan 1, 1949

By E. R. Brownscombe, Francis Collins

The pressure distribution in a reservoir producing an incompressible fluid by radial flow in a horizontal structure is a simple logarithmic function' used daily by reservoir engineers. The assumption of an incompressible liquid is equivalent to assuming that pressure is maintained constant at the well radius and at some external "radius of drainage," or, in other words, that the entire flow into the well passes across the external radius. In most cases a well is surrounded by other wells draining adjoining areas so that the "radius of drainage" is not a line of constant pressure with flow equal to the flow into the well but rather a contour of zero pressure gradient across which no flow occurs, production being due to the expansion of the liquid within the area. The radial flow steady state pressure distribution for this case does not seem to be extensively used despite the fact that the mathematical analysis has been given in detail' and the results are simple and generally applicable. 'The object of this discussion is to develop this result from a physical rather than a mathematical viewpoint, thereby aiding intuition in judging circumstances to which it may be applicable. If the production rate at a well in an unsaturated reservoir is maintained constant while no flow occurs across the outer radius a steady state will soon be reached in which the flow rate or pressure gradient is constant with time at all points in the reservoir. To preserve such a condition it is necessary that the pressure decline at the same rate at all points in the reservoir, that is, the curves of pressure versus radial distance at successive times are all parallel. Then each unit volume of oil is expanding at the same rate and contributing an equal share to the production. The rate of flow q across any circle r is thus proportional to the volume of the reservoir between r and the external radius re, or q = qw (I-r2/r2e) ......(1) where q, is the production from the well and it is assumed that rw is very small compared with re. This equation can be combined with the differential form of Darcy's law for radial flow, 2phkr dp q =—— ........(2) aµß dr ( where q is not a constant as in the incompressible flow case but is a function of r given by Equation (1). If Equation (1) is substituted in Equation (2) the variables p and r can be separated and the result integrated to obtain the pressure distribution p = pw +--------In------------- 2pkh[ rw 2re2] ......(3) This equation differs from the incompressible case only in the addition of the term proportional to the square of the radius

Jan 1, 1950

By O. W. Bilharz

INTRODUCTION ACID mine-water drainage is a serious problem with many mines in the Tri-State zinc and lead mining district. Particularly is this true when large volumes must be considered in unwatering old mines that have refilled with water which has dissolved the products of oxidation and has become chalybeate in character. The experiences discussed in this paper have to do specifically with the unwatering of a comparatively small area west of the town of Baxter Springs, Kans., where the pumping job was complicated by water of this type and where the extremely high sulphate content particularly effected that phase of mine drainage having to do with stream pollution. LOCATION, GEOLOGY AND HISTORY The Baxter Springs area of the Tri-State mining field is situated just west of the town of Baxter Springs and is a northeasterly extension of the main mineralized zones of the Oklahoma part of the district (Fig I). The mining area is traversed with well defined shear zones which provide easy circulation of ground waters and the ore bodies are found along these shear zones as localized enrichments wherever the structural conditions are favorable (Fig 2). The ore-bearing strata is Mississippian with an overlain capping of shale of Pennsylvanian age. This shale strata carries much pyrite and marcasite at its base and undoubtedly was a contributing factor to the subsequent high iron content of the water. The area originally contained a sulphide water which discharged as an artesian flow in springs within the town and gave Baxter Springs its name. These springs were famed for many years for their mineral water. This original sulphide water was first removed about 1917 and active mining was carried on west of the town during subsequent high metal price periods. Many small mines were opened, with each localized enrichment becoming a separate mine. During the depression mining ceased and all mines in the west Baxter area were allowed to flood. No serious effort was made to again unwater until higher prices caused from the demand for metal for World War II once more focused attention on this part of the field. ORIGINAL MINING RESULTS IN OXIDATION As plans for unwatering progressed, it soon developed that the mine-water pools had become strongly acid in character and carried large amounts of sulphates in solution. This occurred in the following way. When the original sulphide water was removed, shafts sunk, and mining carried on over a number of years, ferrous sulphate was formed by the spontaneous oxidation of the pyrite beds in contact with air admitted through churn-drill holes and mine openings. These products of oxidation can be seen today in the old mines of the district as crusts of crystalline sulphates

Jan 1, 1947

By W. G. Pfann

The problem of forming points on wires that were from 0.002 in. to 0.010 in. in diam arose in the recent appearance of silicon and germanium point contact rectifiers as elements in microwave radar.' In these devices a pointed tungsten wire makes a delicate contact with the surface of a semiconductor. Because the quality of such rectifiers is largely determined by the nature of this contact, considerable attention has been given to the formation of the metal point. Reproducibility of contour and freedom from burrs and even microscopic irregularities are considered essential. The operations involved must be simple and rapid enough for mass production. Previously tungsten wircs had been provided with conical points by a grinding method which involved rotating a wire about its axis and causing it to bear at an oblique angle against a spinning abrasive disc. This was later complemented with an electrolytic polishing treatment which removed irregularities from the ground point and also rounded it off at the tip—a desirable feature. Finally, these operations were supplanted by the electrolytic pointing method described here. Mechanism of Point Formation The wires to be pointed are partially immersed in an electrolyte in a vertical position whereupon they are provided with smooth rounded points entirely by electrochemical action. The process is independent of the depths to which the wires penetrate the electrolyte because the points are formed at the surface level. It may be used to point a single wire or many of them simultaneously and is applicable to wires of different diameters within a limited range. Solution of the immersed portion of a tungsten wire is accomplished by making it the positive electrode in an electrolytic cell, as shown in Fig I. While the wire is maintained at constant voltage the current through the cell falls continuously, principally because of the decrease in wetted area which results from solution of the tungsten. This increase in resistance occurs in a reproducible manner and is used as a control in the process. As thc immersed portion of the wire dissolves, it remains cylindrical in shape except for the short section which is wetted by the meniscus. Here the rate of solution is lower and decreases as the top of the meniscus is approached. The result is the formation of a tapered section inside the meniscus. As solution continues, the cylindrical section either dissolves entirely or drops off just before complete solution, leaving only the taper which is now sharply pointed. Further action causes this point to become rounded and then quite blunt, until finally the end of the wire is almost plane. Fig 2 shows the stages in this development. Contour PF is most representative of those used in point contact rectifiers. Thus a variety of point

Jan 1, 1949

By W. M. Bertholf

In 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral call make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory)" as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,' but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1947

By W. M. Bertholf

In 1945 tests were made in the coal washery of the Colorado Fuel and Iron Corporation, at Pueblo, Colo., to determine the value of the Humphreys spiral. So far we have demonstrated that it is of definite value to us in rewashing a portion of our table middlings; and we are fairly certain that this is not necessarily the only place in which it can be used to advantage. Because of manpower and material shortages, experimental work has been discontinued for the present. Three of the spirals are being installed for use in rewashing the middlings, and testing and experimental work will proceed when this installation is completed. All evidence secured so far points to the fact that the spiral call make an effective separation of heavy material below 8-mesh; but that it is ineffective in removing larger, heavy material. This, of course, will limit its use to fine coal or a classified feed containing no heavy material larger than 8-mesh. In considering the results of our tests, it should be noted that the feed was our table middling, and that any real separation of this material is a "moral victory)" as there is little material that could be properly called coal and practically no heavy rock, the consequence being that previous attempts to clean the middlings have not been at all successful. Several articles dealing with the spiral and its use in treating heavy minerals have already been published,' but for the benefit of those who have not seen these we include a brief description of the spiral and of the way it operates, taken from Bulletin 4 of The Humphreys Investment Co.: The Humphreys Spiral Concentrator consists of a spiral conduit of modified semicircular cross section. Ore pulp is fed to the top and, as it flows downward, the heavier particles concentrate in a band along the inner side of the pulp stream (Fig. I). Outlets for removal of products are located at the lowest points in the cross section of the conduit. Wash water, added at the inner edge of the stream, flows outwardly across the concentrate band. The width of concentrate band removed at the outlets is controlled by adjustable splitters. Concentrate is usually removed from the upper portion of the spiral and middling from the lower portion. Tailing is discharged from the lower end. Tests are usually made in closed circuit, since this provides a maximum of information with a minimum amount of sample. Fig. 2 shows the spiral set up for closed-circuit testing, and gives a good idea of the general arrangement of such an installation. The small cyclone separator is used to provide clean wash water without introducing additional water into the circuit.

Jan 1, 1947

By A. M. Gaudin

IT is only in recent years that substantial progress has been made in developing a physico-chemical picture of the solid state. The molecular concept, so useful in dealing with gases, was naturally carried over to the field of crystalline solids; it has resulted in the firm implanting of erroneous concepts that only now are being eradicated successfully. Two simply written and effective books on the subject are Crystal Chemistry by Stillwell1 and An Introduction to Crystal Chemistry by Evans.' A more complete treatment of the subject is available in a book by Wells.' The monograph by Hückel4 also touches on a subject most easily perceived by reference to the brief introduction by Bragg,5 that master of the field. These texts make it clear that while some solids are built of molecules, many are built of ions, others of atoms connected in the form of giant molecules, and still others of cations and electrons. The various lattices in which these entities are systematically arranged, the joint use of several of these entities, and the transitional character of some of the bonds make for the great variety of crystalline solids. The purpose of this paper is to point out a most important corollary of present views on the structure of solids. In this connection the classification of solids in Table I is helpful. Atomic crystals are those formed by the noble gases, e.g., helium and argon. They are soft, sublime at very low temperature, of very low specific gravities, and not encountered in ores. Molecular crystals are uncommon among inorganic materials, common among organic materials. Typical examples from both inorganic and organic fields are sulphur, iodine, naphthalene, benzene, and carbon tetrachloride. These crystals are soft and have low specific gravities; where the molecules are small, the sublimation temperature is low. Filament and sheet crystals are rare. They are typified by elemental selenium and elemental arsenic, respectively. Graphite and molybdenite come near being sheet crystals. These crystals are soft in some directions, tough in others, sublime at various temperatures. Diamantine crystals, typified by diamond, are very few in number, stable at high temperatures, and extremely hard. Ionic crystals are common. Most salts, acids, and alkalies belong in the two classes of ionic crystals; examples are rock salt, fluorite, calcite, and angle-site. The salts, acids, and alkalies that do not belong in these classes are more properly regarded as transitional between ionic crystals, framework crystals, and diamantine crystals, e.g., ice and quartz. Fiber crystals are relatively uncommon mineral-ogically speaking, but common in the fields of living processes. Examples are asbestos, silk, cellulose, and wool. Many fiber crystals are so little known even now that their crystallinity may be doubted. Layer crystals, among the more interesting and useful of solids, include a wide variety of substances

Jan 1, 1956

By John L. Lamont, Walter Crafts

THE principle formulated by Grossmann1 for calculating hardenability of steel by multiplying the ideal diameter of "pure" iron-carbon alloys by factors for grain size and alloying elements has been confirmed on many steels and has proved useful in designing substitute alloy steels. Grossmann found that the typical behavior of the multiplying factors was to increase directly in proportion to the amount of the alloy present in a steel. However, the multiplying factor for the effect of silicon on hardenability was found by Grossmann to increase to a lesser degree as the amount of silicon was increased. In view of the in¬creasing use of silicon in heat-treating steels, the effect of silicon on hardenability is becoming more important. Calculation of the hardenability of high-silicon steels made at the Union Carbide and Carbon Research Laboratories, Inc., indicated that the multiplying factor for silicon increased directly in proportion to the amount of silicon present. A more extended study of high-silicon steels covering fairly wide ranges of grain size, carbon, manganese, and aluminum has confirmed that up to 2 per cent silicon the multiplying factor is directly proportional to the silicon content. Manganese and aluminum factors have also been determined. The results of the study offer strong confirmation of the general validity of Grossmann's multiplying principle. TESTING PROCEDURE Steels on which the study of the effect of silicon on hardenability was based were made in high-frequency induction furnaces using Armco iron and standard alloying materials. The ingots were forged to bars, and sections were normalized prior to machining Jominy hardenability test specimens. The Jominy test was carried out under standard conditions.2 The depth of hardness penetration for determination of ideal diameter at "half hardness" was taken at the hardness level indicated in Fig. 20 in Grossmann's paper by the solid line for 50 per cent martensite in plain carbon steel. The depth of penetration of hardness on the Jominy specimen was converted to ideal diameter by the relation given in Fig. 28 of Grossmann's paper. Chemical analysis was determined on a sample taken adjacent to the Jominy specimen. Aluminum was determined as "acid-soluble aluminum" rather than as total aluminum, as it is probably more representative of the aluminum that is effective as an alloying agent. In addition to the elements nominally present in the steels, analyses were made for residual phosphorus, sulphur, nickel, copper, molybdenum and chromium on one heat of those made with the same materials during the same period. Actual grain size was determined by microscopic examination of small samples quenched in water after receiving the same thermal cycle as the Jominy hardenability specimens. Chemical analyses, heat-treatment, grain size, and hardenability are shown in Table I representing three ranges of composition.

Jan 1, 1943

By V. S. Tuman

In the first part of this paper, an estimate is made of the magnitude and extent of the thermal stresses which result from mud circulation. Our study is made for the period of relaxation, i.e., when the drilling operations are terminated and mud circulation is discontinued. In the second part, we have shown how the thermal stress can affect the wave propagation. An example is worked out for a Carbondale sandstone (Illinois basin). It is concluded that, in extreme cases when differential temperature is about 100°F, the travel time will be affected by about 2 microsec/ft. For more refined permeability studies, such corrections would be desirable. MAGNITUDE AND EXTENT OF THERMAL STRESSES RESULTING FROM MUD CIRCULATION When geological beds are penetrated by boreholes, it is observed that the formation temperatures increase with depth; however, the temperature profile varies considerably from place to place. During drilling operations, mud pumped from a pit at atmospheric temperature absorbs heat from the lower beds. As a result, the drilling fluid returning to the surface is at a higher temperature than the surrounding beds. The temperature gradient in a well depends on the rate of mud circulation and other factors; normally, this temperature gradient is smaller than the natural gradient in the formations. (See Fig. 1.) The temperature difference between the mud column and the surrounding beds gives rise to therma1 stresses (which are also important in the phenomenon of fracturing), and it is expected that they will affect the transit time of the sonic front in velocity logging.1 It is evident chat beds near the surface will undergo various cycles and will have a complicated dynamical and thermal-stress history. A limestone bed which is just penetrated will act as a source of heat, warming up the cold mud pumped down a few minutes earlier from the surface pit. The same limestone bed a week later will act as a sink, absorbing heat from the drilling mud which has already warmed up sufficiently to be at a higher temperature than the bed in question. No doubt a large section of the hole will undergo a heat treatment, which will make the calculation of the exact magnitude of the thermal stresses very difficult. In the solution of wellbore thermal equation, it is assumed that the rock around the wellbore is elastic and isotropic, and that the system is radially symmetrical. A complete dynamical solution of the thermal stresses set up at different horizons during the drilling operations would require a comprehensive history of the mud circulation, the surface temperature of the pit and the number of hours in which mud was not circulated. CONDUCTION OF HEAT AND THERMAL EQUATION OF STATE

By N. Tiner

IN an article on magnesium and its alloys, Gann and Winston1 stated that manganese has a limited solubility in the liquid state. W. Schmidt2 showed a diagram according to Joseph Ruhrmann indicating that the solubility of manganese in liquid magnesium falls from about 2.65 per cent at 790°C. to about 0.5 per cent at 695°C. The curve was extrapolated to show zero solubility at the melting point of pure magnesium (Fig. I): This work suggested that at the lowest manganese contents it was not possible to detect either a eutectic or the formation of a solid solution, so that manganese was stated to be present in the structure as large individual crystals. Two years after the presentation of these results, Gann3 brought evidence to show that some manganese is capable of dissolving to form a solid solution, any excess of manganese present then assuming chiefly the form of small blue-gray particles scattered throughout the primary magnesium crystals, occasionally in clusters but seldom at the boundaries. He presented micrographs of cast alloys containing o.1, 0.4 and 1.0 per cent manganese that show a small amount of coring around the individual particles due to solid solution, and indicate that the location of the manganese particles is closely associated with the original dendritic structure of the primary crystallization. He also pointed out that the amount of manganese that can be dissolved in magnesium depends on the amount of other alloying elements present, the effect of the second alloying element being to decrease the amount of manganese retained in the alloy. E. Schmid and G. Siebe14 have determined the solid solubility of manganese and its variation with temperature by means of precision X-ray diffraction measurements. They found that the solubility is 3.4 per cent at 645°C and decreases to practically zero at 200°C. It is apparent that the X-ray diffraction measurements of Schmid and Siebel are not in agreement with the results of Ruhrmann as presented by Schmidt. This disagreement, and also the lack of data on magnesium-aluminum-manganese and magnesium-zinc-manganese systems, led the author to the present investigation, to determine accurately the liquid solubility of manganese and its variation with temperature. EXPERIMENTAL METHOD The experimental method for making solubility determinations consists of saturating the molten magnesium or the alloys with manganese at various temperatures and analyzing the dip samples taken from these melts. Melting is carried out in a cylindrical steel pot heated by an electric resistance furnace. The pot had a metallic outside coating to protect the steel against oxidation, and a graphite inside lining to prevent the contamination of the melt by prolonged contact with iron. The inside diameter of the pot was 4 in. and the depth 12 inches.

Jan 1, 1945