Search Documents

By J. R. Long, E. T. Hayes, D. C. Root, R. S. Dean

The U. S. Bureau of Mines has recently reported on the development of a process for preparing pure ductile titanium in substantial quantities1 and on the physical properties that may be attained in the metal, when consolidated by powder metallurgy methods and fabricated by certain hot and cold-working procedures.2 The high physical properties (Table I), combined with excellent corrosion resistance and light weight, will lead no doubt to appropriatc applications of the metal. In any application, methods of joining will be of considerable importance. The relatively high activity of the metal toward the common gases raises the question of weldability and conditions that might be required for successful welding. Since hydrogen, oxygen, and nitrogen embrittle the metal, it should be protected from these gases at elevated temperatures. This was demonstrated by a few preliminary trials of arc, gas, and resistance welding. In these trials only the resistance method proved to be immediately- applicable. While atomic: hydrogen welding of titanium may be successful in some instances, a considerable amount of development work will be required to prove its worth. In addition, it would be suited only to small assemblies that could be heated subsequently in a high vacuum to remove embrittling hydrogen. Heli-are methods likewise would be limited to small assemblies, which could be completely protected by a helium atmosphere. It was quite apparent that titanium required more protection than was afforded by the normal flow of helium gas used for welding magnesium and aluminum. The hot metal is attacked by oxygen and nitrogen, and the rapid diffusion of the oxide into the metal prevents the formation of a protective coating and requires the helium atmosphere to be maintained until the weld has cooled nearly to room temperature. The preliminary work indicated that titanium could be successfully spot-welded without deterioration of the metal and that the microstructures of the welds were normal, exhibiting good bonding, and no oxidation. The high resistivity of titanium (53 microhms per cu. cm.) suggested that it would behave somewhat like stainless steel and allow considerable latitude in the several welding variables. The results reported here are intended to give a general picture of the effects of varying welding current, welding time, and tip pressure on single spot welds made on several different thicknesses of titanium sheet. The work was undertaken to demonstrate the feasibility of welding titanium rather than as an exhaustive study of spot welding. There are, therefore, a number of factors that will require further investigation to establish the specific controls required for actual applications.

Jan 1, 1947

By J. R. Long, R. S. Dean, D. C. Root, E. T. Hayes

The U. S. Bureau of Mines has recently reported on the development of a process for preparing pure ductile titanium in substantial quantities1 and on the physical properties that may be attained in the metal, when consolidated by powder metallurgy methods and fabricated by certain hot and cold-working procedures.2 The high physical properties (Table I), combined with excellent corrosion resistance and light weight, will lead no doubt to appropriatc applications of the metal. In any application, methods of joining will be of considerable importance. The relatively high activity of the metal toward the common gases raises the question of weldability and conditions that might be required for successful welding. Since hydrogen, oxygen, and nitrogen embrittle the metal, it should be protected from these gases at elevated temperatures. This was demonstrated by a few preliminary trials of arc, gas, and resistance welding. In these trials only the resistance method proved to be immediately- applicable. While atomic: hydrogen welding of titanium may be successful in some instances, a considerable amount of development work will be required to prove its worth. In addition, it would be suited only to small assemblies that could be heated subsequently in a high vacuum to remove embrittling hydrogen. Heli-are methods likewise would be limited to small assemblies, which could be completely protected by a helium atmosphere. It was quite apparent that titanium required more protection than was afforded by the normal flow of helium gas used for welding magnesium and aluminum. The hot metal is attacked by oxygen and nitrogen, and the rapid diffusion of the oxide into the metal prevents the formation of a protective coating and requires the helium atmosphere to be maintained until the weld has cooled nearly to room temperature. The preliminary work indicated that titanium could be successfully spot-welded without deterioration of the metal and that the microstructures of the welds were normal, exhibiting good bonding, and no oxidation. The high resistivity of titanium (53 microhms per cu. cm.) suggested that it would behave somewhat like stainless steel and allow considerable latitude in the several welding variables. The results reported here are intended to give a general picture of the effects of varying welding current, welding time, and tip pressure on single spot welds made on several different thicknesses of titanium sheet. The work was undertaken to demonstrate the feasibility of welding titanium rather than as an exhaustive study of spot welding. There are, therefore, a number of factors that will require further investigation to establish the specific controls required for actual applications.

Jan 1, 1947

By William F. Ward

One often reads of the rich placer gravels in many of the citnoe-trav-elqd rivers of South America. The apparent richness of these gold-bearing gravels impresses the traveler, and in fact he may see batea after batea showing enough colors to figure over a dollar per cubic yard. These workings are called "playas" from the Spanish word playa, meaning shore or beach. Many workings have been reported in tropical rivers, but to my knowledge no dredge has made a success in such deposits. Investigation generally shows that the area of richness is limited and especially that the depth of the rich concentration is hardly ever more than a few inches. The Cauca river in Colombia, South America, is noted for its many rich playas. This river rises near .Popayan in the southern part of Colombia, flows north through a narrow valley between parallel mountain ranges and empties into the Magdalena river near Maganque. , The airline distance between source and mouth of this river is only about 500 miles. The rainfall is large and the lower Cauca appears to be about the size of the Missouri river in the United States. From its mouth up to Valdivia, in the State of Antioqua, it is navigable. Above Valdivia is a narrow gorge, above which the river is again navigable for some distance. The part of the Cauca where the play a panning is most noticeable is from Valdivia down to where the Nechi river enters the Cauca, a distance along the river of about 100 miles. The current in this part is swift, so that the stern-wheel river steamers make the trip with some difficulty. In the course of my work in this section of Colombia I have had the opportunity to make a study of several of these play a workings and will give in detail the conditions observed. The Island"Playa" The richest of the island playas is about 40 miles below Valdivia and a little below the old town of Caceres. The shape of the river and the location of the deposit are shown in Fig. 1, which indicates the condition at low water. The river at this place is about 600 ft. wide and the island about 75 ft. wide by 300 ft. long. The island is made up of coarse pebbles, some of which are as big as a man's head. In times of high water this island is under several feet of water and in a swift current. When the river lowers the current is still fast enough to prevent sand or silt from covering the coarse pebbles.

Jan 1, 1915

By J. W. Craig, H. L. Walker

Industry has for many years recognized the dependence of certain mechanical and physical properties. as well as workability, upon grain size variations in brass. Although the dependence of properties upon grain size has been recognized there are not many instances where a planned program of testing has been conducted and where the only intentional variable has been grain size. In particular the literature is limited with respect to the effect of grain size on the endurance limit, though there are many industrial applications where the brasses are subjected to cycles of repetitive stresses. Literature A number of the physical and mechanical properties of a given brass sheet, in the annealed condition, will depend upon: (I) The ready-to-finish grain size before final rolling, (2) the percentage deformation by cold working, and (3) the time and temperature of annealing. The first and second variables affect the recrystallized grain size, and the third variable affects the coalesced grain size. Gibbsl has shown the effect of two different ready-to-finish grain sizes upon the tensile strength and hardness of deep drawing brass strip after a definite amount of cold rolling. The smaller the ready-to-finish grain size, the higher the tensile strength and hardness, but with lowered ductility, Gibbs also demonstrated, for a given time and temperature of anneal, that the tensile strength, hardness, and elastic limit are higher for the smaller ready-to-finish grain size, but the elongation is lowered. Townsend and Greena112 have reported data which show that cold working increases the tensile strength, hardness, and load carrying ability of deep drawing brass sheet under reversed stress. Greenall and Gohn3 have reported data which show that the smaller grain sizes have higher tensile strength and hardness properties, and the data also show that increased cold working increases the tensile strength and hardness properties of deep drawing brass sheet. Kommers4 has reported data for tests of brass of known ready-to-finish grain size, a specific amount of cold reduction, and annealed at different temperatures above and below the recrystallization temperature. Kommers' results indicate that annealing below the recrystallization temperature does not change the tensile strength and hardness properties, but the endurance limit may be increased from 22,000 to 28,000 psi. The increased endurance limit is explained as resulting from the reduction of internal stresses by a stress-relief anneal. Burghoff5 and associates have reported data on creep tests, over

Jan 1, 1949

By Irving M. Symonds

COMPA[N]IA Minera de Penoles, S. A., at its Avalos unit operates a lead-zinc concentrator having a capacity of about 600 short tons per day. Lead and zinc concentrates are made by flotation methods. The concentrator is at Terminal de Providencia, in the state of Zacatecas, some 70 miles south of Saltillo, Coahuila. The Pe[n]oles-Avalos railroad operating between the plant and Estacion Avalos, a distance of 6 miles, makes connections with the Coahuila and Zacatecas railroad, which in turn connects with the Nacionales de Mexico at Saltillo. The three railroads are each of different gauge, requiring the transfer of all supplies and concentrates at each junction. The mill operates on company ores, on ores from leased mines, and as a custom mill. The custom business is very small. The lead concentrates are shipped to company smelters at Monterrey, Nuevo Leon and Torréon, Coahuila. Since the European war, all zinc concentrates have been shipped to the United States. ORE TREATED The major source of ore supply is a group of four mines owned or leased by the company, some three miles south of the mill in the mountains, from which the ore is delivered to the mill by a gravity aerial tramway. Custom ore comes in by rail. The ores occur in chimneys. The upper levels contained oxidized siliceous ores of lead, copper, silver and gold, with varying amounts of zinc. These ores were direct-smelted. In the first two years of operation a good deal of the tailing loss was caused by the oxidized content of the ores milled. Much of the ore in the transition zones between the oxides and sulphides was not mined. The ores now being milled are clean, hard sulphides in a limestone gangue, with only occasional contamination of oxides. The lead and zinc sulphides are of coarse structure and are freed even above flotation sizes. The galena is usually "steel" colored, easily and quickly floated. When there is any oxidation, it is usually on the coarsest crystals. The zinc minerals vary a good deal in color; a resin sphalerite predominates but there are varying shades of brown marmatites. On an average, the zinc sulphides contain 64 per cent zinc. The only common copper mineral is chalcopyrite. Little is known of the occurrence of gold and silver. Waste minerals are mainly limestone and pyrite, both of which are barren. The ores vary from 20 to 35 per cent pyrite. Mill heads for the year 1940 and the first eight months of 1941 are given in Table I. [ ]

Jan 1, 1942

By A. L. Johnson, S. C. Lyons

A FEW years ago a leading American builder of centrifuges said, "No one uses a centrifuge if the job can be done any other way." This statement was essentially true at that time, not because the basic functional and economic principles involved did not frequently favor centrifugal methods, but rather because so many of the highly specialized features of the mechanical and functional peculiarities of continuous centrifuges had not been fully developed. The idea of using centrifuges in mineral dressing is definitely not new. There are literally hundreds of patents on centrifugal machines and processes for the mining industry. Many of them cover principles that are basic to the functioning of most centrifuges in operation today. In spite of this, until 1935, there were practically no successful applications of continuous centrifuges in the United States in the mineral industry, nor for that matter were there more than a mere handful of such machines in operation in North America in any industry. This was true despite the obvious desirability of machines that could furnish the advantages of high centrifugal settling forces in a continuous operation. The reasons for this are simple, even if not obvious: I. Finely divided solids, when thrown out of fluid suspension under high centrifugal forces, frequently exhibit physical properties (particularly rheological or flow properties) that are markedly different from those they possess when settled out by gravity alone, and machines that are not designed in careful detail to cope with these peculiarities seldom function satisfactorily. 2. Most continuous centrifuges embody a solids-conveying element in the form of a very special screw conveyor. The rotation of this member under conditions of operation calls for drive designs that were not satisfactorily provided until the introduction of the Bird gear unit about 1934. These matters will be touched on later. Continuous centrifuges are now operating successfully in the mineral industry. Some units have singly handled more than 500,000 tons of solids during the past ten years. Generally their operation has been characterized by large unit capacities, complete elimination of labor, minimum supervision, moderate maintenance and power costs. TYPICAL CENTRIFUGE APPLICATIONS Most materials classified by centrifuges are of subsieve particle size. Practically speaking, this means finer than l00-mesh. A unit of measure other than screens is needed in order to consider these products properly. Such a unit is the micron, which is equal to one one-millionth of a meter; roughly 1/25,000 of an inch. The opening in a standard 200-mesh screen is about 75 microns while a 325-mesh opening is roughly 43 microns.

Jan 1, 1947

By S. G. Valentine

BLAST-FURNACE blowing engines are broadly of two main types: either steam- or gas-driven reciprocating engines, or turbine-driven rotary engines. Some results of experience with a furnace blown by an engine of the latter type may be of sufficient general interest to relate. The first engine of this type was installed at Oxford Furnace, New Jersey, before the writer's connection with this plant, in March, 1910. This furnace uses chiefly New Jersey magnetites and had been in blast seven months on its old engines when the turbo blower was started. It was 80 ft. high by 17 ft. 6 in. bosh and 11 ft. hearth diameter. It is of interest to see from the records what happened when the turbo engine was put to work. But of course, as the old blowing equipment was rather antiquated, consisting of two I. P. Morris engines with air cylinders 72 by 72 in., in good running order, however, it is evident that the comparison between their work and that of the turbo blower cannot be interpreted as being between machines that were respectively of equal excellence as representatives of their types. Still the results were gratifying and -interesting. The records show that, with the old engines blowing 13,630 cu. ft: of air per minute, measured by piston displacement, the furnace was working up about 480 tons of stock per 24 hr. and producing an average of 132 tons per day and a maximum of 166 tons. The rotary blowing engine installed was a General Electric Co. machine, the driving end being a Curtis steam turbine and the air end a six-stage rotary compressor, all running at about 1,500 to 1,600 rev. per minute, and having a capacity of 25,000 cu. ft. of air per minute up to 25 lb. pressure, and equipped with an automatic constant-volume variable-speed governor. After running this blower, for a period equal to that covered above by the old engines, at an average rate of 15,000 cu. ft. of air per minute, the furnace worked up an average of about 592 tons of material and produced an average of 170 tons per day. Thus, on an apparent increase of 10 per cent. in the air volume there was an increase of about 23.5 per cent. in the materials worked up and of about 28.8 per cent. in the product. For the first calendar month's operation of the turbo blower, on an average of 15,040 cu. ft of air per minute, there is

Jan 2, 1914

By Emby Kaye

IT is the purpose of this paper to outline briefly some of the considerations that enter into the economics of so-called recycling, the generic designation of the relatively recently developed process by which a condensate† is separated from gas-distillate gas at high pressure and the residual gas returned to the reservoir. This subject necessarily embraces not only a discussion of factors that should be considered in projecting a recycling operation, such as estimating reserves, investment and operating costs, but also a comparison of condensate with other types of petroleum. The place of condensate in its relation to the total supply of crude oil is pointed out as well as certain logical methods of product disposal. The cost of drilling wells and lease maintenance is not pertinent to this discussion because income and revenue are in this paper confined to that retained by the plant or plant operator for supplying processing facilities for the gas. Before the development of recycling a great many gas-distillate gas fields in Louisiana and. Texas provided no income to their owners. When gas was sold from these reservoirs it was accompanied by irretrievable losses of condensate in the formation. The understanding of the function of retrograde condensation resulted in the introduction of a new commercial petroleum recovery process for these hitherto unexploited fields and now permits the conditioning of this type of wet gas field for the sale of dry gas therefrom without waste. SOME ECONOMIC FACTORS The study of a gas-distillate field for possible exploitation necessarily involves the critical appraisal of a number of elements, chief of which will be discussed here: (I) estimate of distillate in place, (2) estimate of distillate that can be brought to the surface, (3) available market, (4) costs. The considerations affecting the estimating of distillate reserves. in place are in the main subject to the same errors as are involved in determining dry gas reserves. Determinable data including acreage, sand thickness, reservoir pressure, reservoir temperature, porosity and connate water provide the basis for calculating the volume of gas in place. Ample allowance must be made for connate water, which may occupy from 20 to 35 per cent of the pore space of the sand. The factor of supercompressibility is to a considerable extent nullified by the reservoir temperature. It has been considered well advised to allow this factor to serve as a cushion. With the gas reserves calculated, it remains only to assay the distillate content of the gas. Those familiar with the handling of "wet" gas at high pressure readily appreciate the variables in sampling gas from

Jan 1, 1941

By Joseph L. Jernegan

The Whale Lode occurs in the main range of the Rocky Mountains, Park County, Colorado Territory, at Hall Valley. It has been opened up and worked to some extent by the Whale Mine, situated some 11,300 feet above the level of the sea. The mine, with 700 feet of the lode on either side of the discovery shaft, is the property of the Hall Valley Silver-Lead Mining and Smelting Company. The adjacent country rock is a compact, fine-grained gneiss; its general strike is about north and south, dipping steeply to the west. In the immediate vicinity of the mine, the strata are very nearly vertical. The gneiss incloses numberless veins of a reddish granite, in which the feldspar largely predominates over the quartz and mica, the latter oftentimes being scarcely perceptible. As a general rule these granitic veins seem to more frequently follow the lines of stratification of the gneiss than otherwise. They are of varying width, some large, some small; the larger are from 5 to 6 feet wide. Gash veins of feldspar and quartz are also of very frequent occurrence. The general trend of the lode is about northeast. and southwest, intersecting the country rock at about an angle of 45 to its stratification. It dips to the northwest at an angle of 65. I am unable to state accurately how far this lode has been traced upon the surface, but it is at least well known to extend entirely through the mountain upon which the mine is situated, and is traceable over the ridge by a hollow extending for some distance along the surface, in which the lode crops out. This hollow in the surface rock has probably been formed through decomposition of the vein matter by atmospherical influences. The width of the crevice is variable, generally between 5 and 10 feet; the pay vein varies from an inch, or less, to 36 inches. The vein is generally accompanied both on foot and hanging walls by a whitish, semi-decomposed fock, composed of quartz and decomposed feldspar, and in some places—where the process of decomposition has not reached as advanced a stage—a lightgreenish or black mica. This rock, therefore, is in places composed of all the constituents of gneiss, and is undoubtedly nothing more or less than the same in a decomposed condition. It is often very strongly impregnated with iron pyrites, generally crystallized in minute cubes, and it is probably owing to the presence of this min-

By I. L. Dillamore

A purely geomentrical analysis based on oriented-growth relationships is presented to derive annealing-texture orientations in bcc metals from their- known deformation textures. The analysis takes as its starting point a description of- the bcc deformation texture and follows previous work on fcc metals in considering pvobable nurleation sites for recrystallization and the textural limitations on grains growing into a deformed matrix. The analy-sis accounts for the prominent and the minor coinponents of the annealing textures formed from two the deformation textures and can account for the ob-sem:ed temperature dependence of the annealing texture of bcc metals. THERE have been a number of investigations of annealing textures in bcc metals but few attempts to relate these textures to the deformation textures. This has been largely due to the lack of definition of both annealing and deformation textures, neither of which shows sharply defined orientations. It is, however, necessary to get a better understanding of primary recrystallization textures in bcc metals in view of increasingly exacting demands upon the quality of steel sheet for drawing purposes and as a necessary step towards the control of textures through processing. An analysis is presented here which relates annealing textures to deformation texture, by a purely geometrical method. This takes as its basis the oriented-growth theory of recrystallization and makes some reasonable assumptions regarding the make-up of bcc deformation textures and the limitations on growth relationships in bcc metals. Detailed information on this latter point is not available at the present time, and the present analysis may need to be streamlined or extended when such information is at hand. It is felt, however, that despite these limitations the analysis provides useful results and a valuable aid towards understanding the effect of processing variables. 1) BCC ROLLING TEXTURES Different workers have used a variety of descriptions for the texture developed in bcc metals by rolling. For the present purpose it will be assumed that two different deformation textures can be obtained: 1) a texture containing a major (112)[li0] component and a minor (001)[1i0] component for which increasing deformation causes the (001)[li0] component to increase at the expense of the (112)[li0] component, as suggested by Dillamore and ~oberts' (this is the texture predicted to arise starting from randomly oriented material); 2) a t~xture containing the above components and (111)[110] and (ii1)[112] components. This texture could arise from a material with an initial (110)[001] or (iil)[112] texture. It is well-known that the (ll0)[001] orientation rotates to (ii1)[112]that on roll-

Jan 1, 1965

By Helmut Thielsch

During the last three decades a great many arguments have been presented on the subject of "mosaicJ' or "blockJJ structures of metals. Apparently because of insufficient evidence, the "block-structure" theories have never been widely understood among the physical metallurgists in this country, and most investigators among the few that have tried to demonstrate the existence of such an inner strutture Of crystals or grains have failed to recognize also the existence of a lamellar structure. Moreover, little thought has been given to justify the existence of such "lamellar" or "mosaic-block" structures on a theoretical basis. Since properties such as Plasticity; ferro-magnetism, hardness, diffusion, and others may be explained by structural faults in the lattice network of the crystals: the great importance of a more detailed knowledge of the structure within crystals or grains becomes now evident. Because Of the vast extent of the field Of submicroscopic structures, it shall be the purpose Of this paper only to review the more important of the results obtained by other investigators, especially in Germany, where a great deal of attention has been given to mosaic structure during the last three years. The origin of this mosaic patternt and effects of cold reduction and recrystallization will be shown in further studies later on. Imperfections in Crystals The many terms used in the literature to denote structural types of crystals are often not clearly defined. To clear up some of the confusion, the meaning of the more important terms will be given here. ideal, or perfect without any structural imperfections are called "ideal crystals,,or ''Perfect'' crystals,n meaning a Homogeneous interior structure of atoms, ions or molecules, as the case may be. In other words, at every point in the interior of the crystal exactly the same orientation of the crystallographic axes of the coordinate system would exist. The Surface of such a body, if etched with an appropriate etching reagent, would reflect light with perfect uniformity. Crystals of this type are almost nonexistent. Real Crystals.—L'Real crystals"' may contain various types of structural defects, which can be classified into: (I) lineage structure, (2) mosaic-block structure, (3) lamellar structure. The inhomogeneities many,in these groups mean that the orientation of the crystallographic aies will not be the same at every point within the interior of a crystal (or grain of a poly crystalline body). 'Perjecl Real Crystals.—The term "perfect real crystals " is generally used to describe crystals with minute structural or thermo-dynamical inhomogeneities. The former

Jan 1, 1946

By Helmut Thielsch

During the last three decades a great many arguments have been presented on the subject of "mosaicJ' or "blockJJ structures of metals. Apparently because of insufficient evidence, the "block-structure" theories have never been widely understood among the physical metallurgists in this country, and most investigators among the few that have tried to demonstrate the existence of such an inner strutture Of crystals or grains have failed to recognize also the existence of a lamellar structure. Moreover, little thought has been given to justify the existence of such "lamellar" or "mosaic-block" structures on a theoretical basis. Since properties such as Plasticity; ferro-magnetism, hardness, diffusion, and others may be explained by structural faults in the lattice network of the crystals: the great importance of a more detailed knowledge of the structure within crystals or grains becomes now evident. Because Of the vast extent of the field Of submicroscopic structures, it shall be the purpose Of this paper only to review the more important of the results obtained by other investigators, especially in Germany, where a great deal of attention has been given to mosaic structure during the last three years. The origin of this mosaic patternt and effects of cold reduction and recrystallization will be shown in further studies later on. Imperfections in Crystals The many terms used in the literature to denote structural types of crystals are often not clearly defined. To clear up some of the confusion, the meaning of the more important terms will be given here. ideal, or perfect without any structural imperfections are called "ideal crystals,,or ''Perfect'' crystals,n meaning a Homogeneous interior structure of atoms, ions or molecules, as the case may be. In other words, at every point in the interior of the crystal exactly the same orientation of the crystallographic axes of the coordinate system would exist. The Surface of such a body, if etched with an appropriate etching reagent, would reflect light with perfect uniformity. Crystals of this type are almost nonexistent. Real Crystals.—L'Real crystals"' may contain various types of structural defects, which can be classified into: (I) lineage structure, (2) mosaic-block structure, (3) lamellar structure. The inhomogeneities many,in these groups mean that the orientation of the crystallographic aies will not be the same at every point within the interior of a crystal (or grain of a poly crystalline body). 'Perjecl Real Crystals.—The term "perfect real crystals " is generally used to describe crystals with minute structural or thermo-dynamical inhomogeneities. The former

Jan 1, 1946

By V. A. Zanadvoroff

The mine and concentrator of the Howe Sound Co., Chelan Division, are at Holden, in a remote section of the Cascade Mountains of northwestern Washington. Holden is at an elevation of 3200 ft., in the narrow valley of Railroad Creek. This creek drains into Lake Chelan, at a point some 40 miles up the lake from the town of Chelan. The concentrator treats 2000 to 2500 tons of low-grade copper-gold-zinc ore per day. Concentration is achieved by the differential flotation process, with recovery of 94 per cent copper and 82 per cent gold in the copper concentrate, followed by the recovery of 65 to 70 per cent zinc in the zinc flotation circuit. The final flotation tailing is deslimed, and coarse . sands, representing 60 to 70 percent of the total, are cyanided. The tonnage of tailing material amounts to 1900 to 2370 tons per day. General Considerations The property is within the Chelan National Forest. Railroad Creek is a fishing stream, being stocked regularly with trout from State hatcheries. Consequently, in planning a milling operation, the Howe Sound Co. was obliged to avoid any pollution of the stream by tailing material, and also destruction of valuable stands of timber. Moreover, the selected tailing- disposal sites should not mar the natural beauty of the valley. In addition to these requirements, the problem of tailing disposal at Holden was complicated by topography and climatic conditions. The valley is long and narrow, averaging 1200 to 1500 ft. in width. Its walls are flaring at a steep angle. There are no extensive flat areas suitable for deposition of tailing. All valleys tributary to Railroad Creek, also the well-marked paths of snowslides, must be avoided. Finally, the direction of prevailing winds and possible dust hazard arising therefrom dictated the necessity of selecting the tailing-disposal sites downstream from the mill building and two campsites. Heavy snowfall during the winter months of November to March, inclusive, impedes building of the retaining dike, making it necessary to prepare the needed storage space during the summer months. It is inadvisable, also, to do any dike building during the freezing weather, because the dike becomes unstable with the spring thaws, producing inevitable "sloughing" of the built-up borders. Tailing-disposal Sues The existing tailing-disposal areas are near the south wall of the valley. They were developed, and put to use in the following sequence: No. I. Area.—Covers approximately 10 acres. Built up to the height of 60 ft. and abandoned. Total length of dike border is 1900 feet.

Jan 1, 1947

By V. A. Zanadvoroff

The mine and concentrator of the Howe Sound Co., Chelan Division, are at Holden, in a remote section of the Cascade Mountains of northwestern Washington. Holden is at an elevation of 3200 ft., in the narrow valley of Railroad Creek. This creek drains into Lake Chelan, at a point some 40 miles up the lake from the town of Chelan. The concentrator treats 2000 to 2500 tons of low-grade copper-gold-zinc ore per day. Concentration is achieved by the differential flotation process, with recovery of 94 per cent copper and 82 per cent gold in the copper concentrate, followed by the recovery of 65 to 70 per cent zinc in the zinc flotation circuit. The final flotation tailing is deslimed, and coarse . sands, representing 60 to 70 percent of the total, are cyanided. The tonnage of tailing material amounts to 1900 to 2370 tons per day. General Considerations The property is within the Chelan National Forest. Railroad Creek is a fishing stream, being stocked regularly with trout from State hatcheries. Consequently, in planning a milling operation, the Howe Sound Co. was obliged to avoid any pollution of the stream by tailing material, and also destruction of valuable stands of timber. Moreover, the selected tailing- disposal sites should not mar the natural beauty of the valley. In addition to these requirements, the problem of tailing disposal at Holden was complicated by topography and climatic conditions. The valley is long and narrow, averaging 1200 to 1500 ft. in width. Its walls are flaring at a steep angle. There are no extensive flat areas suitable for deposition of tailing. All valleys tributary to Railroad Creek, also the well-marked paths of snowslides, must be avoided. Finally, the direction of prevailing winds and possible dust hazard arising therefrom dictated the necessity of selecting the tailing-disposal sites downstream from the mill building and two campsites. Heavy snowfall during the winter months of November to March, inclusive, impedes building of the retaining dike, making it necessary to prepare the needed storage space during the summer months. It is inadvisable, also, to do any dike building during the freezing weather, because the dike becomes unstable with the spring thaws, producing inevitable "sloughing" of the built-up borders. Tailing-disposal Sues The existing tailing-disposal areas are near the south wall of the valley. They were developed, and put to use in the following sequence: No. I. Area.—Covers approximately 10 acres. Built up to the height of 60 ft. and abandoned. Total length of dike border is 1900 feet.

Jan 1, 1947

The Institute is at present in sound condition professionally and financially. During the past year 546 new members were elected, the total membership now numbering 5,221. The Treasurer's Report shows that the expenses of the Institute are met by its income. Your Directors have thought it wise to issue a referendum to the members asking for a vote upon the suggestion that the annual dues be raised from $10 to $12. This moderate increase is proposed not because the Institute needs it at present but to insure a continuation and increase in its activities and usefulness, and to provide a reserve fund for future emergencies. In well-conducted organizations, such as clubs, it is a wise and safe course to so adjust the clues of members that the total receipts from this source will about equal the annual expenditures, the initiation fees being used for reserve purposes. Our dues alone do not at present meet the expenses. This, I think, is the whole situation, so far as this question is concerned. Expenses might be reduced in some measure, but they cannot be materially reduced without affecting the integrity and usefulness of your Institute. Nothing of consequence in our internal affairs has occurred during the past year except, perhaps, the establishment of the Arizona Section and the prospect now assured of a Nevada Section. During recent months there has been a marked change in the relations of the Institute to its fellow societies and to the Government of the United States. That change is one of cooperation. The Secretary of the Navy has appointed two of your members to the Naval Consulting Board to cooperate with members of 10 other scientific organizations. This Board is now organized, and through its work your Institute is brought in close touch with the activities of the other societies and with the United States Navy. The President of the United States has requested us to recommend to the Government one of our representatives in each State in the Union to act in collaboration with a member in each State from the. American Society of Civil Engineers, the American Society of Mechanical Engineers, the American Institute of Electrical Engineers and the American Chemical Society, thus organizing a directorate of engineers for each State, that will conduct, through the members of each of the five societies referred to, living in each State, a campaign of industrial preparedness. No more important step than this, it seems to me,

Jan 3, 1916

By Joseph L. Jernegan

THE Whale Lode occurs in the main range of the Rocky Mountains, Park County, Colorado Territory, at Hall Valley. It has been opened up and worked to some extent by the Whale Mine, situated some 11,300 feet above the level of the sea. The mine, with 700 feet of the lode on either side of the discovery shaft, is the property of the Hall Valley Silver-Lead Mining and Smelting Company. The adjacent country rock is a compact, fine-grained gneiss ; its general strike is about north and south, dipping steeply to the west. In the immediate vicinity of the mine, the strata are very nearly vertical. The gneiss incloses numberless veins of a reddish granite, in which the feldspar largely predominates over the quartz and mica, the latter oftentimes being scarcely perceptible. As a general rule these granitic veins seem to more frequently follow the lines of stratification of the gneiss than otherwise. They are of varying width, some large, some small; the larger are from 5 to 6 feet wide. Gash veins of feldspar and quartz are also of very fre¬quent occurrence. The general trend of the lode is about northeast and southwest, intersecting the country rock at about an angle of 45° to its stratification. It dips to the northwest at an angle of 65°. I am unable to state accurately how far this lode has been traced upon the surface, but it is at least well known to extend entirely through the mountain upon which the mine is situated, and is traceable over the ridge by a hollow extending for some distance along the surface, in which the lode crops out. This hollow in the surface rock has probably been formed through decomposition of the vein matter by atmospherical influences. The width of the crevice is variable, generally between 5 and 10 feet; the pay vein varies from an inch, or less, to 36 inches. The vein is generally accompanied both on foot and hanging walls by a whitish, semi-decomposed rock, composed of quartz and decomposed feldspar, and in some places-where the process of decomposition has not reached as advanced a stage-a light-greenish or black mica. This rock, therefore, is in places composed of all the constituents of gneiss, and is undoubtedly nothing more or less than the same in a decomposed condition. It is often very strongly impregnated with iron pyrites, generally crystallized in minute cubes, and it is probably owing to the presence of this min-

Jan 1, 1875

By Paul B. Crawford, Bobby L. Landrum

Electrical model studies have been made of the effect of unsymmetrical vertical fractures on production cnpacity. The study war restricted to the case of two vertical fractures originating at the well and extending out into the reservoir for various distances and orientations. The ratio of the short fracture length to the long fracture length was varied from 0.1 to 1.0 in successive studies. The angle separating the two fractures was varied from 0 to 180 degrees. The most effective fractured patterns were obtained when the fractures were oriented 180 degrees. It was found that when the total fracture length was equal to 0.2 of the drainage radius, the increase in production capacity may vary from approximately 1.55 to 1.95. depending upon the ratio of the short fracture length to the long fracture length and the angle separating the two fractures. If the total fracture length were 0.5 of the drainape- radius. poroduction cavacitv., increases varving 1.95 to 2.65 were observed, depending on the angle between the fractures and the ratio of the .short fracture length to the long fracture length. The fractured well production capacity decreased aPproxin?ately I to 10 per cent as the angle separating the fractures was varied from 180 to 90 degrees. It was dependent on the particular fracture. The commercial application of reservoir fracturing techniques has caused an interest to be expressed in the effect of vertical and horizontal fractures on production capacities. Some data have indicated that substantially vertical fractures may be created in some reservoirs. It is believed that the fractures are possibly unsymmetrical, that is, one fracture may extend due north 100 ft and a second fracture on the opposite side of the well may extend south or southeast only 50 ft. The total fracture length, ratios of the lengths and angles of separation may vary considerably. For this reason variations in these factors were considered. The study was restricted to the case of two vertical fractures originating at the well and extending out into the reservoir. It is not known that such will occur in a reservoir, but the results may be of value in interpreting or studying fracturing applications. PROCEDURE An electrical model was used in this study of the effect of unsymmetrical vertical fractures on production capacity, A wooden tank 30 in. in diameter and approximately 2 in deep was coated with paraffin wax. A copper band was situated at the periphery and a single wire electrode was positioned at the center of the tank. The ratio of the reservoir radius divided by the

Jan 1, 1956

By Edward Saibel

THE object of this study is to investigate the effect of prior tensile strain on the fracture stress of a metal. This is done in a theoretical manner starting from the point of view developed by the author in his thermodynamic theory of the fracture of metals. The results are compared with experimental findings and a rational interpretation is given to work that shows the variation of fracture stress with prior tensile strain. THEORY OF FRACTURE In the thermodynamic theory of the fracture of metals developed earlier,1 it was shown that a critical strain energy per unit volume exists. This is characteristic of the material and may be calculated from basic thermodynamic data. When the area under the flow curve reaches this characteristic value, fracture occurs. The general criterion for fracture is expressed in the form u ± uo = JLm?AV/V [1] where Lm, is the latent heat of melting of the unit volume, ?V/V is the ratio of the change in volume of the unit volume to the original unit volume on passing from the solid to the liquid state, [uo] is an initial energy density, and J is a conversion factor, which changes energy from heat to mechanical units. As a first approximation, it will be assumed that the stress-strain curve is the straight line that extends from the point of maximum load onward, extrapolated back to the axis of zero strain, for example, line AC of Fig. 1. If the point of intersection of the straight line with the axis of zero strain is represented by so, and the slope of the straight line is p, the analytic form of the flow curve is [s = s + pd [2]] and the strain energy per unit volume evaluated from [JvdS] becomes (vsod + pd2/ 2). When this latter term reaches the critical value JLm?V/V (designated hereafter by M), it is assumed that fracture occurs. This leads to the following expression for the fracture stress: [s1 = \/C r.2 + 2Mp [31] The strain at fracture may be calculated from Eqs 2 and 3. It is assumed in this paper that the initial energy density is either zero or that it may be neglected. Furthermore, the complicated states of stress and of strain existing in the necked region of the tensile specimen after "necking" has occurred will also be neglected for the present, so that average conditions will be assumed to prevail. FLOW AND FRACTURE CURVES Ludwig2 attributed to materials two fundamental properties: (I) a resistance to flow and (2) a resistance to fracture. He reasoned that at each instant the

Jan 1, 1947

By Carl F. Floe, John Chipman

A YEAR ago the authors published a paper on the solubility of sulphur dioxide in molten copper.1 The data in that paper agreed closely with that obtained by previous investigators, which, however, did not agree with the theoretical predictions for solubility of triatomic gases of this type. It has generally been assumed that the reaction of solution is: [ ] Neglecting the slight change in copper concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume of gas absorbed, it follows that this volume should be proportional to the cube root of the pressure. It was found that a plot of the volume absorbed versus the cube root of the pressure gave a straight line, but that this line did not pass through the origin. Calculations of the equilibrium constant for the reaction showed that it was fairly constant for pressures above l00 mm. but that actually it approached zero at lower pressures. The conclusion was made therefore that the solubility as determined could not be expressed by Eq. I or by any other simple equation, particularly at low pressures. Other investigators have concluded that the solubility of sulphur dioxide in copper as well as in several copper alloys is more nearly proportional to the square root of the pressure.* Such a conclusion, however, does not satisfactorily account for the results, even when rather complicated mechanisms for the solution are assumed. The highly improbable speculations of Lepp2 and of Schneider and Esch3 based upon hypothetical dissociation pressures of Cu20 and (a; 2S dissolved in copper illustrate the type of reasoning that has been used to account for the discrepancy. In the discussion of the previous paper, the authors pointed out that the discrepancy might possibly be due to impurities in the copper, although the purest form available was used. Further consideration of the problem suggested that the impurities likely to have the greatest effect on the solubility of SO2 in copper were oxygen, sulphur and carbon. Accordingly, further experiments have been made to show the effects of these elements. EXPERIMENTAL METHODS The apparatus used for measuring solubility was essentially the same as that shown in the previous paper. However, since it was desired to make measurements at low pressures, a McLeod gauge was added and 6-mm. glass tubing was substituted for the capillary. This increased the "hot volume" considerably but was necessary in order to obtain good vacuums in a reasonable length of time. A mercury diffusion pump was also installed.

Jan 1, 1942

By Y. L. Yao

It is suggested that the binary alloy systems of transition metals may be classified into groups according to "excess energy"E. For systems with positive ?E, the Laves phase, the TiNi3-, the TiCu3- and the Cudu-type rich in the smaller atom and the TizNi-type rich in the larger atom may exist. For systems with negative ?E and composed of two components of different crystal structures, the X, the Cr3O and the phase may exist on the side of the phase digrattz rich in the component with the higher "solubility factor" value am! the Cudu-type and the disordered hcp phase on the other side; if the crystal structure of two components is the same, the Cudu-type may exist on both sides. For systems with weakly positive ?E and cotnposed of different crystal structures, the u phase and the MgCd3-type may replace the Laves phase and the other types; the X, the Cr3O and the a phase may also exist. Finally, the equirnolar compounds of the CuAu- and the CsC1-type may exist irrespective of the sign of ?E. THERE are many factors which play a major role in the formation of binary intermediate phases in alloys, such as the crystal structure, the electronic structure, the atomic size and the electrochemical factor. To find the simultaneous effects of all these factors on the formation of intermediate phases of every metal would be a difficult task, especially because only a small fraction of experimental facts necessary for the complete formulation is known at present. Thus the past surveys of intermediate phases have been usually confined to few metals, several types of intermediate phases and some but not all controlling factors. In a previous paper1 the idea of "solubility factor" of metals was introduced. Although the suggested values are tentative and empirical, the formation of a continuous series of solid solutions in metals could be correlated with the interplay among the atomic size factor, the solubility factor and the crystal structure factor. The purpose of this paper is to demonstrate qualitatively the interplay of these factors in the formation of binary intermediate phases among transition metals. FACTORS CONSIDERED The Crystal Structure Factor. With rare earths excluded, the transition metals are classified into three common crystal structures listed in Table I. There is arbitrariness in the present classification of several allotropic elements. However, out of seventy-odd continuous solid solutions formed among transition metals, only six of them, namely, those

Jan 1, 1962