Search Documents

By Marshall B. Standing, Donald L. Katz

DENSITY data are reported on 16 saturated hydrocarbon vapors at pressures ranging from 1000 to 8220 lb. per sq. in. and at temperatures ranging from 35° to 250°F. These data have been used to extend the compressibility-factor chart for natural gases up to 10,000 lb. per sq. in. The relatively large quantity of high-boiling constituents present in high-pressure vapors in equilibrium with crude oils makes it necessary to include in the analysis of the gas the molecular weight, density, and possibly boiling range of the heptanes and heavier fraction. Relationships have been presented by which the density of gases may be obtained directly from the temperature, pressure, and gas gravity provided the gases have a common source or are similar in composition. INTRODUCTION The densities of natural gases are necessary in many engineering computations in petroleum production and utilization. Gas reserves, changes in reservoir pressure, gradients in gas wells, metering of gases, pipeline flow, and compression of gases are typical problems requiring the density of the gas. A decade ago, engineering computations used ideal gas laws with deviations up to 500 lb. per sq. in.4 Recent discoveries of pools having pressures up to 7500 lb. per sq. in., and installation of pressure-maintenance and recycling plants, have increased the need for data on gas density at high pressures. METHODS OF COMPUTATION The accepted method of computing the density or specific volume of natural gases is the use of the ideal gas law corrected by a compressibility factor. The method proposed by Kay7 of correlating compressibility factors for gaseous mixtures on pseudocritical properties5 appears to be satisfactory for natural gases.2 The methane-compressibility factor has been shown to deviate systematically from the behavior of natural gases2 and a chart giving these corrected factors is available. A method of computing specific volume of gaseous mixtures from partial molal volumes has been reported by Sage and Lacey.8 Complete data for the computation are not yet available for all hydrocarbon gases. Most of the reported data on gas densities have been in the single-phase region removed from the dew point or saturation condition. Since most gases in the reservoir or while on contact with liquid during flow are saturated, the determination of densities under conditions of saturation is particularly important. Although there is no reason to believe that the saturated gases differ in behavior from those considerably removed from their dew points, the usual experimental determinations find difficulty on approaching the dew-point conditions. This paper reports the density of 16 saturated gases in equilibrium with crude oils. The relationships developed to compute the density of gases to high pressure' have been modified and enlarged. A simplified method of obtaining gas density is presented in the form of charts, which apply for specific groups of gases.

Jan 1, 1941

By R. M. Leibrock, C. W. Ziemer, R. P. Vincent

The Stanolind flowmeter, which employs a hot-wire anemometer connected in a Wheat-stone bridge circuit, has proved useful for determining the relative productive ability of individual sand members of gas wells. The operation of this instrument in measuring gas velocities in the well bore above each producing member has provided both a direct and accurate means of analyzing reservoir performance. Results of tests conducted with the well flowmeter in the Hugoton gas field of western Kansas have indicated some rather unusual production characteristics. In two cases it was found that all or the greater part of the total gas produced was coming from one section in wells where four "pay" sections had been perforated individually. These actual measurements contradict in many instances the indications of data obtained from electric logs and from core analysis; the fact that these latter sources often give incorrect results, demonstrates the necessity of a method, such as is provided by the well flowmeter, for accurately determining the amount of gas coming from each producing member. Introduction In any gas well where a number of pay sections have been perforated individually and are producing to a common outlet, the question arises as to the relative amounts of gas being passed through each set of perforations. In the past it has been the policy to depend on core analysis to estimate relative productivities, or, where the sections were not cored, to obtain some idea of production characteristics from electric-log studies. The weaknesses in these methods are readily apparent and indicate the need for more reliable means of measuring gas flow from each zone. The Stano-lind flowmeter* was developed for this purpose. Preliminary tests were made with the instrument in the Katy gas field near Houston; however, the bulk of the routine work with the well flowmeter has been confined to the Hugoton gas field in western Kansas, where results obtained have been encouraging. A description of the instrument, the field technique employed in testing, and a few of the results obtained in the Hugoton area are discussed in this paper. Description or Instrument The well flowmeter is 1¾ in. od and 7 ft long; it is entirely self-contained, can be run through tubing as small as 2 in. id in wells with high pressure (4500 psi) and temperature (210°F) and is lowered on a wire line commonly used for other instruments of the bottom-hole type at falling rates up to 500 ft per minute. It will detect gas flow as low as 10 ft per minute linear velocity, and yet withstand and record velocities of 1000 ft per minute without damage to the detecting element. Killing the well is not required nor desirable for running a production profile when using the instrument, and it is necessary to stop flow for only a short time. The detecting element of the instrument is a hot-wire anemometer connected in a

Jan 1, 1948

By R. M. Leibrock, R. P. Vincent, C. W. Ziemer

The Stanolind flowmeter, which employs a hot-wire anemometer connected in a Wheat-stone bridge circuit, has proved useful for determining the relative productive ability of individual sand members of gas wells. The operation of this instrument in measuring gas velocities in the well bore above each producing member has provided both a direct and accurate means of analyzing reservoir performance. Results of tests conducted with the well flowmeter in the Hugoton gas field of western Kansas have indicated some rather unusual production characteristics. In two cases it was found that all or the greater part of the total gas produced was coming from one section in wells where four "pay" sections had been perforated individually. These actual measurements contradict in many instances the indications of data obtained from electric logs and from core analysis; the fact that these latter sources often give incorrect results, demonstrates the necessity of a method, such as is provided by the well flowmeter, for accurately determining the amount of gas coming from each producing member. Introduction In any gas well where a number of pay sections have been perforated individually and are producing to a common outlet, the question arises as to the relative amounts of gas being passed through each set of perforations. In the past it has been the policy to depend on core analysis to estimate relative productivities, or, where the sections were not cored, to obtain some idea of production characteristics from electric-log studies. The weaknesses in these methods are readily apparent and indicate the need for more reliable means of measuring gas flow from each zone. The Stano-lind flowmeter* was developed for this purpose. Preliminary tests were made with the instrument in the Katy gas field near Houston; however, the bulk of the routine work with the well flowmeter has been confined to the Hugoton gas field in western Kansas, where results obtained have been encouraging. A description of the instrument, the field technique employed in testing, and a few of the results obtained in the Hugoton area are discussed in this paper. Description or Instrument The well flowmeter is 1¾ in. od and 7 ft long; it is entirely self-contained, can be run through tubing as small as 2 in. id in wells with high pressure (4500 psi) and temperature (210°F) and is lowered on a wire line commonly used for other instruments of the bottom-hole type at falling rates up to 500 ft per minute. It will detect gas flow as low as 10 ft per minute linear velocity, and yet withstand and record velocities of 1000 ft per minute without damage to the detecting element. Killing the well is not required nor desirable for running a production profile when using the instrument, and it is necessary to stop flow for only a short time. The detecting element of the instrument is a hot-wire anemometer connected in a

Jan 1, 1948

By A. V. Deforest, C. W. Macgregor, A. R. Anderson

One of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing or the A.S.T.M., 1938. The work of Mann.' Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserves especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by P ALo plotting So = 1/A0 as a function of eo = ALr,o where A0 and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors.7'8 It was shown that the true physical behavior of the material in the tension test could best be represented P by plotting the average true stress, S = 2P as a function of 6 = q' = log —r = log ~9L where P, A, L, S, E, and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximin load point to fracture. The construction of such curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain dificulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece diameters to fracture under impact conditions offers considerable experimental difficulty. In order to make it feasible to

Jan 1, 1942

By A. V. Deforest, A. R. Anderson, C. W. MacGregor

One of the important problems in the design of structures and machine parts subjected to rapidly applied loads is the determination of the strength and ductility of the material itself under such conditions. Realizing the need for such information, many investigations have been carried out in the past. Most of these experiments have been made using notched bars in bending either with the Charpy or Izod impact machine. While yielding valuable data on the effect of notches in the energy absorption of the material and on the condition of heat-treatment, this form of test does not lend itself readily to a determination of fundamental stress-strain relations. For this and other reasons, more attention has been paid recently to the tension impact test. An extensive literature already exists on the subject and only those investigations somewhat closely related to the present paper will be mentioned. For a more comprehensive list, the reader is referred to the Symposium on Impact Testing or the A.S.T.M., 1938. The work of Mann.' Clark and Dätwyler,2 Nádai and Manjoine,3 Winlock and Leiter,4 Deutler,5 and Brinkmann,6 however, deserves especial mention. In most of the previous investigations on the subject, when stress-strain relations were obtained under high rates of loading, it was the common procedure to determine stresses based on the original area and strains based on the original length. Stress-strain curves were then constructed by P ALo plotting So = 1/A0 as a function of eo = ALr,o where A0 and Lo refer to the original area and gauge length, respectively. At present there exists a paucity of true stress-strain data in the impact problem. The advantages of constructing so-called true stress-strain curves in order to reveal the fundamental physical properties of the material for the tension test were discussed recently by one of the authors.7'8 It was shown that the true physical behavior of the material in the tension test could best be represented P by plotting the average true stress, S = 2P as a function of 6 = q' = log —r = log ~9L where P, A, L, S, E, and q' refer to the load, the cross-sectioned area while the load P is applied, the actual gauge length, the average true stress, the true strain and true reduction in area, respectively. Besides giving a better physical representation, the method has certain additional advantages in that the stress-strain curve so plotted becomes a straight line from the maximin load point to fracture. The construction of such curves, however, while comparatively simple for the slow rates of loading customarily used in the tension test, presents certain dificulties for tensile impact in that both loads and diameters are required throughout the test. The continuous measurement of test-piece diameters to fracture under impact conditions offers considerable experimental difficulty. In order to make it feasible to

Jan 1, 1942

By I. J. Logan, Warren L. Baker

By 1950 or soon thereafter facilities will be available in foreign countries for the production, transportation, and refining of about 4,305,000 bbl per day of crude oil—a volume not far short of current United States output. This is indicated by announced plans for foreign expansion, - some of the work being already under way. The projected potential production is about 1,500,000 bbl per day or 50 pct above the record-setting foreign production of 2,810,000 bbl daily in 1946. The scheduled new foreign facilities are equivalent to almost one third of the present facilities of the United States. Fears that so much additional foreign oil may flood world markets and disrupt the domestic industry of the United States are not justified. The projected foreign expansion apparently has been planned on a sound business basis, with careful consideration of the world's actual need for all the projected additional production. Materially increased world demand for petroleum promises to absorb the increased supplies without ill effect upon the domestic industry. Even by applying conservative estimates of both foreign and domestic demand, it is indicated that world requirements can absorb the projected larger foreign output and still permit continued increase in United States production. World demand would have to increase only 5.7 pct per year in the 1947 to 1950 period to absorb the prospective supply. Such an increase may be conservatively projected, in view of past and current trends. Introduction Recent announcements of plans for expanding petroleum facilities in the Middle East and Venezuela foreshadow an unusually sharp increase in foreign production in the immediate future. Therefore, the next few years will bring far-reaching changes in world petroleum affairs, with foreign petroleum production and other activities assuming much greater importance than formerly. Tabulation of figures on development already under way or planned indicates that in the next several years facilities will be available for producing, transporting and refining twice the prewar production of foreign fields and about 50 pct or nearly 1,500,000 bbl a day above their record-level output of 1946. To say that foreign fields may be producing such an enlarged quantity by 1950 is, of course, a statement of great significance to everyone connected .with the oil industry and especially to those of the American petroleum industry. A production of 1,500,000 bbl daily is equal to the combined yield of the states of Oklahoma, Kansas, Illinois, Louisiana, Arkansas, Mississippi and New Mexico. This means that within the next several years foreign petroleum facilities will undergo a new expansion equivalent to one third of the present facilities of the United States. To think of such an expansion in foreign production is to raise at this meeting the question of what this prospective foreign development means for the United States, the American petroleum industry in general, and the American engineer and technologist in particular. It is only logical to question whether or

Jan 1, 1948

By Warren L. Baker, I. J. Logan

By 1950 or soon thereafter facilities will be available in foreign countries for the production, transportation, and refining of about 4,305,000 bbl per day of crude oil—a volume not far short of current United States output. This is indicated by announced plans for foreign expansion, - some of the work being already under way. The projected potential production is about 1,500,000 bbl per day or 50 pct above the record-setting foreign production of 2,810,000 bbl daily in 1946. The scheduled new foreign facilities are equivalent to almost one third of the present facilities of the United States. Fears that so much additional foreign oil may flood world markets and disrupt the domestic industry of the United States are not justified. The projected foreign expansion apparently has been planned on a sound business basis, with careful consideration of the world's actual need for all the projected additional production. Materially increased world demand for petroleum promises to absorb the increased supplies without ill effect upon the domestic industry. Even by applying conservative estimates of both foreign and domestic demand, it is indicated that world requirements can absorb the projected larger foreign output and still permit continued increase in United States production. World demand would have to increase only 5.7 pct per year in the 1947 to 1950 period to absorb the prospective supply. Such an increase may be conservatively projected, in view of past and current trends. Introduction Recent announcements of plans for expanding petroleum facilities in the Middle East and Venezuela foreshadow an unusually sharp increase in foreign production in the immediate future. Therefore, the next few years will bring far-reaching changes in world petroleum affairs, with foreign petroleum production and other activities assuming much greater importance than formerly. Tabulation of figures on development already under way or planned indicates that in the next several years facilities will be available for producing, transporting and refining twice the prewar production of foreign fields and about 50 pct or nearly 1,500,000 bbl a day above their record-level output of 1946. To say that foreign fields may be producing such an enlarged quantity by 1950 is, of course, a statement of great significance to everyone connected .with the oil industry and especially to those of the American petroleum industry. A production of 1,500,000 bbl daily is equal to the combined yield of the states of Oklahoma, Kansas, Illinois, Louisiana, Arkansas, Mississippi and New Mexico. This means that within the next several years foreign petroleum facilities will undergo a new expansion equivalent to one third of the present facilities of the United States. To think of such an expansion in foreign production is to raise at this meeting the question of what this prospective foreign development means for the United States, the American petroleum industry in general, and the American engineer and technologist in particular. It is only logical to question whether or

Jan 1, 1948

By John P. Dolan, Charles A. Einarsen, GiIman A. Hill

his paper discusses how the following formation characteristics can be determined mathematically from drill-stem test pressure charts: true formation pressures, effective permeability of the entire section tested, well productivities, wellbore damage, and possible detection of barriers (faults, pinchouts, etc.). This paper also presents a practical method for im-mediate determination of eflective permeability and well-bore damage from successful double shut-in pressure tests. A list of recommendations for improving the reliability of drill-stem rest pressures is also presented. INTRODUCTION A drill-stem test is a temporary completion designed to sample the formation fluid and to establish the possibility of commercial production. Early pressure recording devices were used merely to verify proper operation of the testing tool. Until recently the accuracy of the pressure gauges has been insufficient for any reliable quantitative use of the recorded pressures. In view of the need for more reliable formation evaluation and as a result of the recent interest in exploration work employing the concept of hydrodynamic en-trapment,1,2,3,4 better pressure recording gauges are now in use. These devices can record pressure within 1 per cent above 1,000 psig and can detect differential pressures as low as 1/2 psig. In addition to formation pressure, several other reservoir characteristics can be determined from DST charts; namely, well productivity, formation permeability, wellbore damage, and the possible existence of bar- riers (faults, pinchouts, changes in permeability, etc.). This paper presents a practical method to interpret DST pressure charts for formation pressures and many other reservoir properties, a method that has been developed in analyzing approximately 4,000 DST charts during the last five years. The techniques used are a composite of published articles on drill-stem testing5,6, together with well-known pressure build-up analysis methods. THEORY It has been shown7,8 that the following equation may be used for analysis of pressure build-up curves: Po - Pw = 162.6 qu/kh log ( to + ?/?) .....(1) When this equation is applied to the curves obtained in drill-stem testing, the assumptions and boundary con-ditions are more nearly realized than in conventional flow and build-up tests on producing wells. Zak and Griffen9 have recently discussed in detail the use of this equation in analyzing DST charts. One of the problems with DST curves is the lack of reservoir data for precise analysis. Therefore, it is necessary to develop empirical rules and field methods for analyzing DST charts in quantity. For this reason, the empirical methods presented in this paper have been developed, and their derivation is found in Appendices A and B. METHOD USED FOR ACCURATE READING OF DRILL-STEM TEST CHARTS In order to apply the pressure build-up theory to DST charts, it is necessary to obtain a digitized expression for the pressure and time data recorded by the pressure gauge. These data may be either provided by the service company or interpolated by projecting a

Jan 1, 1958

By Nelson Severinghaus

Mineral fillers have been defined as inert materials that are included in a composition for some useful purpose. Because this definition and the scope of this review are not specific-indeed, exceptions abound-accurate total statistics are unavailable. One source estimates the total production in the United States in 1979 at 11.3 Mt (12.5 million st) valued at $534 million, averaging $49.19 per ton. Included are a broad group of minerals-asbestos, barite, bentonite, ground limestone and dolomite, clays, diatomite, feldspar, micas, silica, talc. Additional references will be made to synthetic mineral-derived fillers such as aluminum hydrate, precipitated calcium carbonate, and pyrogenic and precipitated silicas and silicates. A section on related uses at the end of this chapter covers absorbents and filters. Mineral fillers can be included in compounds to accomplish a variety of final results. Hardness, brittleness, impact strength, compressive strength, softening point, fire resistance, surface texture, electrical conductivity, and a host of other physical characteristics may be modified by the inclusion of fillers. These effects are the result of properties of the fillers, including chemical activity, hardness, particle size, shape and distribution, surface structure, color, density, and refractive index. To facilitate an overview of the mineral filler industry, this chapter will review the general usage of fillers, the inherent characteristics that intensify their utilization, and similarly their manufactured characteristics. Major using industries will then be examined in detail. Specific information on deposits and processing for industrial minerals will be found in the appropriate commodity chapter. All of these same minerals have additional significant uses based on their chemical composition or other characteristics. References will be found in other use chapters and summarized in commodity chapters. The chart in Table 1, updated from the 4th edition of Industrial Minerals and Rocks, illustrates the major mineral fillers (both natural and manufactured) and their more important end uses. Use of Mineral Fillers Archaeologists have found that more than 5000 years ago, bitumen used for mortar and waterproofing contained mineral contaminants that acted as fillers. Since that time man has added mineral products to compounds to improve certain characteristics. Perhaps the most common objective of filler usage is reduction of cost of the end product. Certainly the inclusion of a filler that costs 2¢ per 0.45 kg (lb) will reduce the cost of a plastic product whose resin costs 50¢ per 0.45 kg (lb). But the decision to use a specific filler is not that simple. It may "soak up" binder, making a compound more viscous and perhaps preventing its flow into a mold as an injection molding compound, but similarly will give good anti-sag characteristics to putty, caulking compound, or undercoating. Fillers may be incorporated to modify: 1) Cost 2) Physical characteristics 3) Flow characteristics 4) Fire resistance 5) Density 6) Heat conductivity 7) Color or brightness and opacity 8) Hardness, brittleness, impact strength 9) Deformity, viscosity, softening point 10) Processing problems 11) Electrical conductivity 12) Surface texture 13) Thermal expansion characteristics 14) Abrasion resistance

Jan 1, 1983

By H. R. Peiffer

The increase in electrical resistivity, ?pT,at 78°K was measured as a function of elongation, E, at 78°K for a 2 pct (approximately) by weight finely divided alumina in silver material. The amount of increase in electrical resistivity (?pT) is a function of the amount of alumina present and can be represented by: ?pT = cen where c and n are constants. The constant c increases and the exponent n decreases with increasing alumina content. Approximately 33 pct of the resistivity increase is recovered upon annealing at room temperature. RECENTLY, dispersed phase alloys' have shown promise for use at elevated temperatures. These materials have a high creep resistance, a high-temperature strength considerably above that of the pure matrix, and a high electrical conductivity. These materials also show other properties such as retardation of re crystallization and resistance to flow even above the melting point of the matrix.' It is believed that high-temperature creep is retarded in these materials because the dispersed phase blocks the motion of dislocations. According to schoeck3 and also Weertman,4 the rate controlling process is the climb of dislocations around the dispersed phase particles. Any mechanical property of these materials, or any other material for that matter, can be explained on the basis of defect structures and their interrelations. It would certainly be interesting to learn something about the effect of a dispersed phase on dislocation densities and also their effect on point defect concentrations following cold work. This is the purpose of the research discussed herein. The method used was the measurement of the electrical resistivity as a function of elongation at low temperatures. This scheme has already been applied to the studies of pure metals.5 Electrical resistivity measurements conducted on pure metals such as copper, silver, gold, and so forth, have indicated that defects such as vacancies and dislocations are formed during deformation.5 It has been shown by van Bueren6 that the resistivity change, ?p, should increase with elongation, E, according to the following relation: Ap=Al/2 + B£3/2 where A and B are constants of the system; ?p is in µ? cm. The first term refers to the amount of resistivity change associated with line defects and the second term with the change associated with point defects. A later calculation yielded exponents of 3/4 and 5/4, respectively.6 Manintveld7 has shown that the resistivity of copper increases with strain according to a 3/2 power law, whereas van Bueren has shown that the resistivity of silver increases according to a 5/4 power law. Assuming then that van Bueren's calculations are correct, it appears that line defects contribute very little to the electrical resistivity. There is some doubt, however, as to the validity of van Bueren's expressions for all cubic metals.' In fact, the data on copper and silver are not conclusive. In this in-

Jan 1, 1962

By Dorsey Hager

North Central Texas has recently become a center of interest for the oil men of America. The bringing in of the McClosky well at Ranger, Eastland County, and the shallow pool at Brownwood, Brown County, in 1917, has stimulated interest in this area to fever pitch. Oil men from all over the United States are now investing there. The area of present interest is shown by the accompanying map (Fig. 1). The money spent in leases runs into millions of dollars. It is no exaggeration to say that a strip of country 200 miles (321 km.) long and 125 miles (201 km.) wide, comprising some 15,000,000 acres (6,070,310 ha.), has been leased practically solid at a cost for rentals and bonuses of at least $1 per acre. The test holes contracted for will certainly number 400, at a cost of at least $5,000,000. From what has been done in the past six months, $20,000,000 at least will be spent. To pay returns on this amount of money, new production to the extent of at least 12,000,000 bbl. must be obtained. At present, the production from new fields will not average over 5000 bbl. per day; three wells at Ranger are producing 3000 bbl.; 250 wells at Brownwood produce 1000 bbl.; and the Gray well, Coleman County, is as yet an unknown factor. However, at Ranger there is every indication of developing a good pool covering from 1500 to 2000 acres (607 to 809 ha.), more or less, but the wells are deep, 3400 to 3800 ft. (1036 to 1158 m.), and cost $35,000 to $40,000 to drill. Large wells are necessary to pay for such expensive holes. As new wells are drilled, the gas pressure will be lowered rapidly, and large production need not be expected. For those oil men who expect a second Cushing or an Eldorado, Ranger holds little of promise. At Brownwood, Brown County, there are some 250 shallow wells (depths from 200 to 350 ft.) averaging 4 to 7 bbl. per day. There is a chance of an extensive producing area for these shallow sands to the southwest, and the opening of several thousand acres of shallow oil territory, and also some promise of deeper oil horizons in the Ranger horizon, but probably all under 2500 ft. At present, the lease brokers and speculators, and only a handful of oil men, have made any money. More fields must be developed, and it is more particularly with these possibilities that this paper deals. Lack of water for drilling purposes has undoubtedly held back development so far this year; this part of Texas has had a drouth for two years and there is an actual scarcity of water. Geological investigations so far undertaken cover nearly all the area outlined, and while pakt of the

Jan 1, 1920

By J. C. McDonald

A DDITIONAL experimental data are presented in this note on a phenomenon which has been touched on but lightly in the literature. The common magnesium base rolling alloy (AZ31B) contains about 3 pet A1 and 1 pet Zn. When cold rolled, it hardens until it starts to break up in the rolls at 30 to 50 pet reduction. When it is heated after rolling to full hardness, it softens. However, other magnesium alloys have shown themselves capable of being cold rolled indefinitely, provided the ratio of roll diameter to starting gage is sufficiently high. As measured by the tensile test, these alloys actually soften when the reduction becomes large (60 to 90 pct). A subsequent heating at 300' to 500°F can produce hardening of this metal. Heating at higher temperatures (600' to 800°F) causes recrystalliza-tion and softening. Menzen' has shown that a magnesium base alloy can be cold rolled without intermediate anneals as much as 90 pet. The alloy studied, Mg-1.5 pet Mn, softened considerably between 20 and 90 pet reduction, as measured by tensile properties; a decrease in yield strength of 30 pet, and an increase in elongation from 3.2 to 16.7 pet (longitudinal direction of the sheet). However, Menzen gives no data on the reaction of this metal. to heating. Ansel and Betterton2 and Hurst and Hatch3 report a similar effect in Mg-1.5 pet Mn-0.1 pet Ca. Their data show an initial hardening, followed by softening. The former authors also show that the alloy softened by cold rolling will harden when heated at low temperatures, and that these effects are absent in Mg-3 pet Al-1 pet Zn. In the course of work4, 5 some years ago, the author observed similar effects with alloys containing cerium, thorium, or zirconium; but not with elements like aluminum, silver, or zinc. Table IA contains the results of an experiment which shows these effects rather well. A binary alloy with 0.3 pet total rare earths (Mischmetal* added) was rolled hot to 1/16 in. and then annealed to full softness by heating 30 min at 800°F. Rolling was continued at 1.5 pet per pass to 80 pet total reduction on 8 in. diam rolls. The metal was harder after 20 pet work than initially but, at 80 pet reduction, properties were back to their original values. Heating for 1 hr at 450°F produced about the same hardness whether the reduction was 20 or 80 pet. At intermediate reductions, the metal hardened, but not to as high values. Extensive cold rolling may also be carried out on metal hot rolled at temperatures sufficiently low to produce a semihard temper. Mg-0.6 pet Zr was rolled to 0.1 in. at 700° to 800°F, 30 pet per pass. As shown in Table IB, a further cold reduction of 85 pet, at 1.5 pet per pass, definitely softened the metal.

Jan 1, 1959

By J. H Lightfoot, Stuart E. Buckley

Deep drilling has led to the development of numerous pools which yield products consisting predominantly of natural gas accompanied by high-gravity water-white or slightly straw-colored liquid. Yields of this "condensate" or "distillate," as it is commonly called, vary from traces to over a hundred barrels per million cubic feet of gas. The fact that this liquid exists in the reservoir as an integral part of the gas phase and is formed by condensation attending simultaneous reduction of pressure and temperature after its entry into the well was apparently first recognized about 1932.l The nature of the physical phenomena involved in this condensation was clarified for the petroleum industry in 1933 by a report by Sage, Schaafsma, and Lacey2 of the results of an experimental investigation of the behavior of mixtures of methane and propane. Search of the literature has revealed that the condensation of liquid from gaseous mixtures by isothermal pressure reduction is not a new discovery. Kuenen was led by theoretical considerations to expect such a phenomenon, and in 1892 reported3 the results of experimental verification of his deductions. This was followed by a considerable amount of work on the phase relations of mixtures by Kuenen 4,5,6 and by 0thers,7,8 mostly in European universities. Since 1930 investigators in this country have reported experimental data on the properties and behavior of a number of hydrocarbon systems."' It is now generally known that in the presence of natural gas the solubility in the gas phase of the heavier and normally liquid hydrocarbons increases rapidly with increasing pressure above 500 to 1000 Ib. per sq. in. Thus, at pressures of 2500 Ib. per sq. in. or higher a gas may contain appreciable quantities of hydrocarbons with normal boiling points as high as 6o0°F., which in turn may be condensed from the gas phase by the reduction of their solubility therein attending pressure reduc-tion. The combined effects of pressure and temperature on condensation and vaporiza-tioi of mixtures are most readily visualized by the study of phase diagrams. Since the construction, application, and interpreta-tion of such diagrams have been described fully in readily available literature, 18-20 this paper will not review the theoretical aspects of this subject. While the behavior of gas-distillate sys tems is now clearly understood, at least in a qualitative way, most of the published work deals with the results of laboratory studies of binary systems or of synthetic mixtures of hydrocarbons, and although several systematic investigations of the effects of separator pressure and temperature on the yields of liquid product from gas-distillate wells have been made21,12z it appears that in all cases the limitations have precluded the construction of even approximately complete phase diagrams for naturally occurring systems. There has 2

Jan 1, 1941

By J. H. Lightfoot, Stuart E. Buckley

Deep drilling has led to the development of numerous pools which yield products consisting predominantly of natural gas accompanied by high-gravity water-white or slightly straw-colored liquid. Yields of this "condensate" or "distillate," as it is commonly called, vary from traces to over a hundred barrels per million cubic feet of gas. The fact that this liquid exists in the reservoir as an integral part of the gas phase and is formed by condensation attending simultaneous reduction of pressure and temperature after its entry into the well was apparently first recognized about 1932.l The nature of the physical phenomena involved in this condensation was clarified for the petroleum industry in 1933 by a report by Sage, Schaafsma, and Lacey2 of the results of an experimental investigation of the behavior of mixtures of methane and propane. Search of the literature has revealed that the condensation of liquid from gaseous mixtures by isothermal pressure reduction is not a new discovery. Kuenen was led by theoretical considerations to expect such a phenomenon, and in 1892 reported3 the results of experimental verification of his deductions. This was followed by a considerable amount of work on the phase relations of mixtures by Kuenen 4,5,6 and by 0thers,7,8 mostly in European universities. Since 1930 investigators in this country have reported experimental data on the properties and behavior of a number of hydrocarbon systems."' It is now generally known that in the presence of natural gas the solubility in the gas phase of the heavier and normally liquid hydrocarbons increases rapidly with increasing pressure above 500 to 1000 Ib. per sq. in. Thus, at pressures of 2500 Ib. per sq. in. or higher a gas may contain appreciable quantities of hydrocarbons with normal boiling points as high as 6o0°F., which in turn may be condensed from the gas phase by the reduction of their solubility therein attending pressure reduc-tion. The combined effects of pressure and temperature on condensation and vaporiza-tioi of mixtures are most readily visualized by the study of phase diagrams. Since the construction, application, and interpreta-tion of such diagrams have been described fully in readily available literature, 18-20 this paper will not review the theoretical aspects of this subject. While the behavior of gas-distillate sys tems is now clearly understood, at least in a qualitative way, most of the published work deals with the results of laboratory studies of binary systems or of synthetic mixtures of hydrocarbons, and although several systematic investigations of the effects of separator pressure and temperature on the yields of liquid product from gas-distillate wells have been made21,12z it appears that in all cases the limitations have precluded the construction of even approximately complete phase diagrams for naturally occurring systems. There has 2

Jan 1, 1941

By D. H. Turner, F. A. Crossley

The titanium-rich corner of the system Ti-Al-Si has been studied to determine the phase relationships in the temperature interval 600° to 1200°C. Metallographic examination of long time isothermally annealed specimens was the means of investigation. PART of a program on phase relations and transformation processes of titanium alloy systems included the study of the titanium-rich corner of the Ti-Al-Si system. The investigation covered ternary compositions in the range 2 to 8 pet A1 and 0.1 to 2 pet Si and binary compositions in the range 0.2 to 2 pet Si. Temperatures were in the range of 600" to 1200°C. Alloys containing 6 pet A1-0.1 to 0.5 pet Si were investigated down to 400°C. Partial vertical sections are presented for 2, 4, 6, and 8 pet Al. The Ti-Si system has been reported by Hansen et al.' It is characterized by a eutectoid decomposition, ß = ± a + Ti3Si3, at 860°C. The maximum solubility of silicon in a is reported to be about 0.5 pet at the eutectoid temperature. The solubility of silicon in 0 increases from 0.9 pet at the eutectoid temperature to approximately 3 pet at the eutectic temperature, 1330°C. Several investigations in the composition range of interest have been reported for the Ti-A1 system."' These investigations are in agreement on the phase fields, but differ to small extents on boundary positions. However, very recent, and as yet unpublished, findings" " indicate that there are perhaps two phases which occur at lower aluminum contents than the ? (TiA1) phase, and that the solubility of aluminum in a titanium is less than 6 pet. In the present investigation phase relations found are in agreement with the published literature exemplified by the work of Bumps et al.3 Therefore, it is probable that the partial system reported herein is metastable and does not represent true equilibrium. Experimental Procedure High purity Bureau of Mines titanium sponge of 103 Bhn hardness, granulated aluminum shot of 99.7 pet purity, and silicon powder of 99.8 pet purity were used in making the alloys. For the work in the range from 600" to 1200°C, 100 g ingots were prepared by arc melting. Melting losses were negligible and spot checks by chemical analysis showed good agreement between nominal and analyzed results. Nominal compositions are used throughout this paper. Ingots were forged to 3/8 in. rounds and cut into specimens for heat treatment. Isothermal anneals in the range from 600" to 900°C were preceded by solution treatment at 1000°C for 1 hr, followed by furnace cooling to the annealing temperature. Samples were sealed in evacuated Vycor bulbs for heat treatments up to 1000°C. Higher temperature anneals were done with the samples sealed in quartz bulbs under a partial pressure of argon.

Jan 1, 1959

At all business meetings of the Institute the President, or, in his absence, the First Vice-President, or, in the absence of both of them, any other Vice-President or Director, chosen by the meeting, shall preside. At all other meetings of the Institute the President, or, in his absence, one of the Vice-presidents shall preside. If none of these be present the meeting shall elect a Chairman. The President shall do and perform such other duties as may from time to time be assigned to him by resolution of the Board of Directors of the Institute. II. ORDER OF BUSINESS. At each business meeting of the Institute the order of business shall be as follows: 1. Reading of minutes of preceding meeting. 2. Report of the President. 3. Report of the Treasurer. 4. Report of the Secretary. 5. Election of Directors. 6. Reports of Standing Committees. 7. Reports of Special Committees. 8. Special Orders. 9. Miscellaneous business. This order of business may be changed at any meeting, by a vote of a majority of the Members and Associates present. At all sessions of the Institute, other than business meetings, the order of proceedings and the time of adjournment shall rest in the discretion of the presiding officer. III. SECRETARY OF THE INSTITUTE. The Secretary shall keep a record of the proceedings of all the meetings of the Institute, He shall be custodian of the corporate seal, of the minute books and of all the legal documents belonging to the Institute. He shall have charge on behalf of the Institute of all correspondence. He shall notify all Officers and Directors and all members of committees of their election and appointment; shall issue notices of all meetings of the Board, and of the annual and other business meetings of the Institute; and shall, in calling special meetings of the Directors, specify the objects of such meetings. He shall act as clerk at all the meetings of the Board of Directors and at all meetings of the Institute. The Secretary shall be custodian of all technical or scientific papers submitted to the Institute for its consideration and shall have general charge and supervision of the editing and proof-reading of all material published by the Institute, and of the distribution thereof. The Secretary shall be the custodian of all back numbers of the Transactions and other publications of the Institute. There shall be kept under his direction an account in ledger form of all such back numbers. He shall on the first day of January of each year submit to the Library Committee a statement of the number of copies of Transactions, magazines and other publications printed during the preceding year, giving the number distributed and remaining undistributed; also a statement covering additions to and withdrawals from the total stock of Institute publications, with the number remaining on hand at date of statement.

Jan 1, 1928

By T. J. Fabiniak, R. A. Dodd, R. Balow

ALTHOUGH the (111) slip direction in pure bcc metals is well established, the information on operative slip planes is less unambiguously interpreted. So far, (110) {112), and (123) slip planes have been identified, but it is not certain whether glide on (112) and (123) really occurs or if it is composite slip on non-parallel (110) planes. The second of these possibilities is supported by the work of Chen and Maddin on niobium and molybdenum, and a subsequent analysis by these same workers of slip in bcc metals generally.3 The alternative possibility is exemplified by the work of Opinsky and smoluchowsky4 who concluded that slip in Fe-Si crystals can occur on any one of the systems {110}(111), {112}(111), and {123)(111), depending on which system the resolved shear stress is highest. Allen et alS5 also found that glide in ar iron could occur on any of these three systems, the operative system being determined principally by orientation. By an analysis of crystal rotation, slip lines, and X-ray asterism Harris6 concluded that niobium also deforms on these same systems, but if one of these glide planes does not coincide with the plane of maximum resolved shear stress, composite slip on nonparallel (110) planes may occur giving a macroscopic high indices slip plane. Earlier work on iron by Vogel and Brick reached the same conclusion.7 The analysis of slip in bcc metals is made more difficult by the fact that the slip lines may be quite wavy. In fact, the generality of wavy slip lines suggests that screw dislocations slip readily from one plane to another in the (111) zone ("pencil glide") although, as noted, it is not certain whether planes other than (110) really contribute to the slip. If planes of higher indices than {110} do operate, there is a possibility they may do so more readily at higher temperature Argon and Maloof9 observed {100}{211}(111) slip in tungsten single crystals plastically strained at low temperatures, but the results were interpreted in terms of an orientation-dependence rather than temperature-dependence. Therefore, at the present time corroborative evidence for the operation of higher indices slip planes at higher temperatures is lacking. The present results were obtained during the course of an investigation into the effect of cathode and anode surface crystallography on the prebreakdown currents of vacuum insulated devices. In the experiment of particular interest, the 1/8-in.-diam anode and the in.-diam cathode were tungsten crystals (total impurities -230 ppm) with (110) and (100) faces respectively. The faces were electrolytically planed and examined for initial perfection by plastic/carbon replicas and a study of Kikuchi lines in reflection electron diffraction patterns. They were aligned precisely parallel in an insulating holder incorporated into the electron microscope, the measured microscope vacuum being 2 x 10-5 torr, and the electrode spacing 0.01524 cm. The anode structure shown in Fig. 1 was obtained

Jan 1, 1970

By L. S. Castleman, H. A. Froot

A study was made of the growth kinetics of B-brass layers in a-brass us y-brass diffusion couples in which both phases were saturated in the 6 phase. It was found that useful estimates can be made of the difhsion coefficients at the ß-phase interfaces from interface displacement data, which are relatively easy to measure experimentally; also, a useful estimate can be made of the mean heat of activation for diffusion from layer growth data. The effects of pressure on layer growth kinetics were explored and found to be consistent with a vacancy model for diffusion in 6 brass in both the disordered and ordered temperature range. 1 HE study of multiphase diffusion receives relatively little attention in comparison with that devoted to diffusion in homogeneous materials. Of the hundred or so papers on diffusion written each year,' only a few are devoted to the subject, and it is the rare review article2,3 that devotes any space to multiphase diffusional phenomena. This is unfortunate, since the metallurgist frequently encounters practical situations involving cementation processes such as cladding, protective coating of metals, and so forth in which he needs guidance of a fundamental nature. The investigation of multiphase diffusion phenomena is complicated by the fact that one must consider reactions at phase interfaces as well as the migration of atoms within the individual phases; these reactions cause the interfaces to be displaced within the diffusion zone. The relative displacement of two adjacent interfaces corresponds to the growth of an intermetallic layer, and it is not difficult to determine experimentally the kinetics of layer growth. In the past few years it has been pointed out4,5 that valuable fundamental information may be gained about diffusion coefficients and the concentrations at interfaces through a study of their motion. Accordingly, it is the purpose of this paper to report the results of an investigation of interface motion in a simple multiphase binary system. In the work reported herein, attention was focussed on the growth of a 6 -brass layer in a diffusion couple prepared from a- and y-brass compositions saturated with respect to the 6 phase. This particular system was chosen for a number of reasons. First, the bcc ß-brass phase is disordered for all compositions at temperatures above 468°C and becomes increasingly long-range ordered for all compositions at temperatures below 454° C;6,7 thus, the effects of a variation in order on interface displacement could be determined. Second, diffusion coefficients have already been obtained as a function of temperature in the ß phase both in the ordered and disordered Re- and a theoretical picture of the mechanism of diffusion in this and other ordered solutions is emerging.11'12 Third, some thermodynamic data are available for the a-, ß-, and ?-brass phases,13,4 and these data could be used to gain insight into questions of phase equilibria and concentrations at phase interfaces.

Jan 1, 1963

By J. E. Lawrence

Copper-decorated lattice disorders in silicon have been analyzed by electron transmission microscopy, chemical etching, and P-N junction reverse current measurements before and following different gettering treatments. Lattice disorders acted as the nucleating sites for copper precipitation. Copper precipitates in silicon resist chemical etching, absorb electron beams more than silicon, and cause excess reverse currents. Totally gettered disorders will chemically etch rapidly, be transparent to electron beams at extinction contrast, and not contribute to excess reverse currents. Three different gettering procedures were performed to determine the effectiveness of different EXTRANEOUS metal contamination can alter the minority carrier lifetime and resistivity of bulk silicon as well as cause excessive reverse currents in semiconductor devices. Previous workers have reported such activity for gold,1,2 copper,'-* iron,' and rnanganese.2,5 Gettering is a method employed to render these impurities electrically inactive. However, some property of the junction-degrading metals prevents gettering procedures from being wholly reliable. The comparative effectiveness of gettering with different agents has been the topic of earlier publications.2,3,6-11 Two mechanisms for gettering metallic impurities have been proposed: the distribution coefficient mechanism by Thurmond and Logan7 and the compound formation mechanism by Goetzberger and Shockley.2 Both of these models evolved from data gettering mechanisms. First, phosphorus was allowed to enter a protective SiO2 film but remain away from the Si-SiO2 interface to test the effectiveness of the compound formation gettering mechanism. Second, phosphorus was allowed to enter the backside of silicon wafers to test the effectiveness of the lattice strain gettering mechanism. Finally, nickel was diffused into the backside of silicon wafers to test the effectiveness of the distribution coefficient gettering mechanism. In each case, copper precipitates dissolved as a result of the gettering treatment. Tightly packed precipitates will resist gettering more than loosely packed copper precipitates. acquired by the electrical analyses of gettered semiconductor materials. An electrical analysis, however, cannot identify the fate of the gettered metals. The radiotracer technique has recently been applied to determine the redistribution of metals following different gettering treatments.3,9,10 The spatial resolu tion of the radiotracer technique prevented the analysis of metal precipitates which contribute to the excessive reverse currents of P-N junctions. The gettering processes employed by the earlier workers, almost without exception, allowed the gettering agent to enter the silicon lattice. This procedure makes it quite difficult to differentiate between the distribution coefficient and the compound formation mechanisms. The metallographic analysis of gettered copper precipitates discussed in this work supplements the earlier work by obtaining direct evidence of silicon lattice defects decorated with copper before and following different gettering treatments. The effectiveness of a process which restricts the gettering agent, phosphorus, to a dielectric film and thus away from the silicon lattice is discussed in addition to the ef-

Jan 1, 1969

By C. W. Donnelly, Louise B. Freeman, Coleman D. Hunter

It is with pride that the authors of this paper report. that during 1944 the production of petroleum in Kentucky passed its all-time peak, 9,496,985 bbl. being contributed. The delivery of natural gas, especially from eastern Kentucky, was maintained and possibly exceeded the highest deliveries of the past. To raise the production of oil and gas was not easy with inferior and worn-out equipment and the shortage of skilled labor. Reminiscent of the early days of the industry in the state, particularly in the hills of Elliott County, where mud roads often have gradients of 45º, was the replacement of worn-out trucks and tractors by oxen. Of the total 9,496,985 bbl., 17 per cent was contributed by the part of Kentucky that is east of the Cincinnati arch, as compared with the total of 7,010,776 bbl. contributed in 1943, of which 25 per cent was contributed by eastern Kentucky. This discrepancy is due to the discovery of more new fields in western Kentucky rather than to a decrease in production in the eastern fields, where the average has been maintained by reconditioning and secondary recovery of old fields and further development of new pools reported for the first time in 1943. In all, 1103 wells were known to have been drilled in the state during 1944, of which 659 were drilled in western Kentucky and 444 in eastern Kentucky. The exact number of wells drilled for any year is never known, as drilling permits are not required except 'when it is planned to drill through a workable coal seam. Of the total number of wells drilled, 459 were oil wells, 229 gas wells and 415 dry holes. The monthly production was as follows: January........................... 659,496 February.......................... 658,606 March...................... ...... 711,619 April............................. 649,926 May............................... 754,892 June.............................. 730,369 July.............................. 761,762 August............................ 878,053 September...................... 863,150 October........................... 968,732 November........................ 961,999 December........................ . 898,636 Western Kentucky In western Kentucky 352 wells were completed as oil wells with a total initial production of 47,922 bbl. of oil, the average being 136 bbl. per well. Two wells produced gas, the total initial production being 1,594,000 cu, ft. One hundred and eighteon wildcat wells were drilled, of which 107 were dry holes and 11 were oil wells. Three of the latter proved to be the discovery wells of commercial pools. Twelve new pools were discovered during 1944, none of major importance, as indicated in Table 2. The Utley pool, due to a stratigraphic trap on the flank of a closed structure, found oil in the Mcclosky at 2565 ft. in the discovery well, with initial productioil of 1000 bbl. The average daily production is now 227 bbl. from seven wells. The East Poole field, with the discovery well in the Tar Springs sandstone at 1811

Jan 1, 1945