Search Documents

By A. H. Geisler, R. F. Mehl, C. S. Barrett

The mechanism by which the supersaturated solid solution of 20 per cent silver in aluminum decomposes has been reported in two previous publications.1'2 The analysis of streaks in Laue photograms showed that thin platelike particles (the so-called Guinier-Preston aggregates) form upon matrix planes in the early state of decomposition.1 The size of these particles is larger, the higher the temperature at which they form in accordance with nucleation theory;³ at all temperatures they increase in size with aging.2 When they have grown thick enough to afford three-dimensional diffraction, powder X-ray photograms show that the structure is not that of the equilibrium precipitate but that of a transition lattice . Sincc this is also platelike in shape and also lies upon the (III) matrix planes with the [IIO] direction in the matrix parallel to the [II.O] direction in it seems likely that the original platelet particles are merely in an early stage of formation, and thus finely dispersed. The atomic spacing and pattern on the (00.1) plane in y' are identical with those on the (111) matrix plane to which it lies parallel, and since comparable directions in the two planes are parallel, the lattices are thus coherent at the interface; an analogous coherence has been found in aluminum-copper alloys.3 The structures y' and y are both close-packed hexagonal and are oriented alike; they differ only in interatomic distances. Consequently, y' is regarded as y strained from its ordinary dimensions by the lattice coherency between it and the matrix.2 The lattice movements that transform the matrix to the equilibrium precipitate appear to be very simple.2 The mechanism of precipitation in this system is simpler and is more precisely known than that in any other system hence the system should be a profitable one for the difficult task of correlating property changes with structural alterations. The present report provides additional studies on powder X-ray diffraction from alloys of 10 per cent, 20 per cent and 30 per cent Ag, and presents the correlation of crystallographic changes with changes in microstructurc, Brinell hardness and electrical resistivity of the three alloys. Preparation of Samples and Experimental Procedure The preparation of the 20.2 per cent Ag alloy has been described2 Alloys containing 9.9 and 29.7 per cent Ag were prepared from 99.97 per cent A1 and 99.99+ per cent Ag using a similar procedure. Rolled

Jan 1, 1943

By R. F. Mehl, C. S. Barrett, A. H. Geisler

The mechanism by which the supersaturated solid solution of 20 per cent silver in aluminum decomposes has been reported in two previous publications.1'2 The analysis of streaks in Laue photograms showed that thin platelike particles (the so-called Guinier-Preston aggregates) form upon matrix planes in the early state of decomposition.1 The size of these particles is larger, the higher the temperature at which they form in accordance with nucleation theory;³ at all temperatures they increase in size with aging.2 When they have grown thick enough to afford three-dimensional diffraction, powder X-ray photograms show that the structure is not that of the equilibrium precipitate but that of a transition lattice . Sincc this is also platelike in shape and also lies upon the (III) matrix planes with the [IIO] direction in the matrix parallel to the [II.O] direction in it seems likely that the original platelet particles are merely in an early stage of formation, and thus finely dispersed. The atomic spacing and pattern on the (00.1) plane in y' are identical with those on the (111) matrix plane to which it lies parallel, and since comparable directions in the two planes are parallel, the lattices are thus coherent at the interface; an analogous coherence has been found in aluminum-copper alloys.3 The structures y' and y are both close-packed hexagonal and are oriented alike; they differ only in interatomic distances. Consequently, y' is regarded as y strained from its ordinary dimensions by the lattice coherency between it and the matrix.2 The lattice movements that transform the matrix to the equilibrium precipitate appear to be very simple.2 The mechanism of precipitation in this system is simpler and is more precisely known than that in any other system hence the system should be a profitable one for the difficult task of correlating property changes with structural alterations. The present report provides additional studies on powder X-ray diffraction from alloys of 10 per cent, 20 per cent and 30 per cent Ag, and presents the correlation of crystallographic changes with changes in microstructurc, Brinell hardness and electrical resistivity of the three alloys. Preparation of Samples and Experimental Procedure The preparation of the 20.2 per cent Ag alloy has been described2 Alloys containing 9.9 and 29.7 per cent Ag were prepared from 99.97 per cent A1 and 99.99+ per cent Ag using a similar procedure. Rolled

Jan 1, 1943

By Jr. W. L . Phillips

The deformation and fracture characteristics of lithium-fluoride single crystals stressed in compression at room temperature have been studied. In as-cleaved specimens the stress-strain curves were variable; two types of {110} fractures were observed in the vicinity of kink bands. The stress-strain curves of annealed crystals were reproducible; {100} cracks formed which propagated along the (100) and (110) planes. The deformation and fracture characteristics were affected by quenching and X-ray irradiation. STUDY of the mechanical behavior of nonmetallic materials has received considerable impetus in recent years because of the need to overcome the problem of brittleness before the refractory properties of nonmetallics can be fully exploited. Ionic crystals provide a convenient and simplified starting point from which to study the deformation and fracture processes in nonmetallic materials. Early investigations of the mechanical behavior of non-metals were restricted largely to determinations of the crystallographic indices of the cleavage and fracture planes and the glide and twinning elements. Until recently, only occasional systematic studies of the deformation characteristics of non-metals have been made; and investigations of the forces necessary to initiate plastic deformation and the factors which affect the flow characteristics have been restricted largely to studies of sodium chloride'-7 , magnesium oxides-l3 and lithium fluoride. 14-22 Fracture studies on alkali halide and metal oxide single crystals have been limited despite the fact that these materials have a number of advantages for fracture studies. Because they are transparent, the cracks which form can be viewed in three dimensions instead of in two dimensions as in metals. Also, they exhibit stress birefringence under polarized illumination, which enables the internal stress pattern and, therefore, the distribution of dislocations to be examined in the vicinity of the fracture. Early workers1-4 have shown that ionic crystals with a cubic structure fracture in tension along the (100) plane normal to the applied stress. These fractures were brittle at room temperature and propagated very rapidly across the cross section of the crystal. More recently, Stokes, Johnston, and Lil0 have studied crack formation in compressed magnesium-oxide single crystals. They found that the cracks, which were observed after about 3 pct strain, formed in the region of a kink band and lay on conjugate (110) slip planes instead of the usual(100) cleavage plane. Two different types of cracks were noted: stroh23 and secondary. The Stroh cracks did not exist merely on the surface but extended through the specimen in the form of tiny slits. A secondary

Jan 1, 1962

By F. H. Wilson, R. M. Brick

WITH the papers of Palmer and Smith1 and of Burghoff and Bohlen,2 published in 1942, understanding of the problem of the development of ears on deep-drawn brass cups was brought to the point where, from a practical standpoint, producers of brass sheet could keep earing under control. However, these very practical results raised questions concerning the reasons for the observed behavior. Since plastic deformation is fundamentally a function of crystallographic slip, these reasons must be considered in the light of the textures to be found in the annealed sheet. Various attempts have been made to interpret the mechanism of ear formation by correlation with the preferred orientation and the anisotropy of the sheet. However, none of these has satisfactorily explained why ears are usually found in the rolling and transverse directions for copper but at 45° to these directions for brass. This paper offers additional data on these two related subjects and has been divided into two sections. The first section provides a survey of the recrystallization textures of brass as affected by annealing temperatures and prior reductions, and an account of the earing behavior which accompanies these textures. The second section reports new data on the anisotropy that accompanies a characteristic texture for brass and endeavors with partial success to establish the factors that account for the difference in earing behavior between copper and brass. EARING BEHAVIOR OF BRASS Review of Textures The recrystallization texture of severely rolled brass was first reported by Bass and Glocker.3 The preferred orientation to which this texture, obtained from metal annealed at 500°C., was most akin was (113)[112]. This texture has been confirmed by Bauer, von Göler and Sachs;4 Brick;* Brick, Martin and Angier;6 and Cook and Richards7 who, in general, used annealing temperatures under 500°C. Bass and Glocker3 also reported the recrystallization texture at 850°C. to be the same as at 500°C. They analyzed their textures by means of single photograms obtained with white radiation. The photograms for both temperatures are reproduced in their paper, and there is a strong similarity between the two. However, for the latter temperature, the number of spots registered on the film was remarkably large for the grain size to be expected, and the authors made no mention of using a technique that would integrate a large enough area of the specimen to produce so many spots. The only other attempt to determine textures resulting from high temperature

Jan 1, 1945

By Byron M. Bird

JIGGING is the stratification of a mass of solid particles in upward pulsations of water or in alternating upward and downward pulsations. The stratification usually is effected in a rectangular open-top container having a perforated bottom through which the pulsations of water are applied to the materials to be separated; in separating coal, to a mass of coal and refuse. Jigging usually is a continuous process involving three steps: (1) the reception of the raw coal, (2) the stratification of the coal and refuse so that the refuse settles to the screen plate, and (3) the overflow of the cleaned coal and the withdrawal of the refuse collected on the screen. The jig is the most universal washer ever devised. It is handling in practice a wide range of closely sized coals and ores, mixed sizes of coal from 8-in. to 0 through ¾ -in. to 0, and mixed sizes of ores down to 7/32-in. to 0 and even smaller. It is treating materials ranging in specific gravity from that of gold at 19 to that of coal at 1.30. It is handling feeds in which the proportions of high-gravity materials range from 90 per cent or higher, as for some iron ores, to 10 per cent or less for some coals. It is handling feeds containing all shapes of particles-round, rectangular, and , flat. It is handling simple separation problems and difficult separation problems. Thus, it is an almost universal separating device. One might add that it has been one of the most misunderstood types of washers, from both a theoretical and a practical point of view. Although considerable progress has been made in coal jigging in the past 10 years, the jig probably has more unexplored possibilities than any other type of washer. In this chapter the object has been to treat the jigging process in a practical manner and to give information that will help the reader to improve his particular operation. Inasmuch as performance data from operating plants would contribute little of value, none has been given. Instead, the emphasis is upon jigging principles as a foundation for attacking the problems that arise. These principles are in reality tentative conclusions from research in the field of jigging during the past 10 years and most of this chapter should be regarded as a progress report on an investigation still under way. As all really difficult problems in jigging arise from an attempt to treat a large range of sizes in one operation, nearly the entire discussion will be

Jan 1, 1943

By E. W. Davis

On the eastern end of the Mesabi Range, in Northern Minnesota, is a large formation of siliceous rock which contains bands and fine grains of magnetite. The magnetite comprises about 35 per cent. of the rock, the remainder being chiefly quartzite and iron silicates. The rock has a specific gravity of 3.4, a hardness of 7, and is extremely tough. This large deposit was located early in the history of the Minnesota iron-ore industry but has not been utilized because of its low percentage of iron as compared with the other Mesabi ores, and because of the difficulty and expense of any milling treatment that would concentrate the iron. An investigation, begun about 3 years ago, shows that the magnetit,e is finely disseminated throughout the entire formation and that there are bands or lenses of higher- and of lower-grade material, in which the magnetite and silicate are intimately mixed. As a result, the scheme of milling adopted must include a fine-crushing plant. As it is necessary to crush to 200 mesh in order to produce the desired grade of product, the fine crushing is one of the largest items of expense and for this reason has been given detailed study. It is the purpose of this paper to present some of the results of the work on fine crushing, as to both theory and practice. Previous to fine crushing the part of the rock that contains little or no magnetite can be discarded by magnetic concentrators after each reduction in size in the dry-crushing plant. This-makes it possible to fine-crush a minimum of rock and also establishes the feed to the ball-mill as below % in. The fine-crushing problem, then, consists simply in crushing the rock from 1/4 in. to 200 mesh at the minimum expense. Equipment of the Testing Plant In order to determine, among other things, the operating conditions of the ball-mill when working on this rock, a test mill of about 300 T. daily capacity was erected at Duluth, Minn. The fine-crushing plant contains a Hardinge 8-ft. by 22-in. (2.4-m. by 55.8-cm.) conical mill, a 6- by 27-ft. (1.8 by 8.2-m.) Dorr duplex bowl-type classifier, a 41/2-ft. (1.37-m.) standard Akins classifier, and the auxiliary machinery necessary to handle the products. Each machine is driven by an individual motor, each of which is provided with meters for measuring the power required. Over 150 tests have been made in the ball-mill, varying in

Jan 1, 1920

By A. H. Daane, J. J. Hanak, F. H. Spedding

IN the study of the rare earths at the authors' laboratory, methods have been devised for preparing pure rare earths and many of their properties'- have been determined. Very little information is found in the literature on the properties of europium metal, which is the scarcest of the naturally occurring rare earths. Since we have recently prepared europium in appreciable quantities, we are in a position to describe the method of preparation and some of the properties of this metal. Metallic europium was first prepared by Klemm and Bommera who heated a mixture of potassium and EuC1, in vacuo, and obtained a mixture of europium metal and KC1. Trombe4 electrolyzed a molten salt bath containing NaC1, KC1 and EuC1, and collected the europium in a molten cadmium electrode as a cadmium alloy. The cadmium was subsequently removed by distillation but the properties of the residue indicate that pure europium was not obtained. McCoy attempted to prepare europium by distilling mercury from europium amalgam, but the stability of the Eu-Hg intermetallic compounds prevented a complete separation of the two elements. The preparation of very pure europium was suggested by previous work in this laboratory1,4 in which ytterbium and samarium were prepared by heating the respective sesquioxides with lanthanum metal turnings to 1450°C in vacuo and distilling ytterbium and samarium from the mixtures. Subsequently, small test experiments showed that europium also could be prepared by this method. A more detailed version of this method was used in the work described in this paper. Klemm and Bommer3 found by X-ray analysis that the metal had a body-centered cubic (bcc) structure with a lattice constant a, = 4.582 ± 0.00A (converted from kX units), with a bulk density of 5.30 g per cu cm. They found europium to be weakly ferromagnetic. Spedding, et al,7 found a,, to be 4.606 ± 0.001A. Barrett' showed that the bcc structure persists throughout the temperature range 5 to 3000K with a, at 5, 78, and 300°K being 4.551 ± 0.003, 4.551 ± 0.004 and 4.577 ± 0.001A, respectively. Trombe1 described europium as being iron gray, malleable, about as hard as neodymium and not attacked by cold water. He estimated the melting point to be between 1100 and 1200°C. Previous work in this laboratory indicated that the pure metal corrodes rapidly in air and reacts with cold

Jan 1, 1959

By Frank L. Nason

The complete statistics of zinc-ore production in the United States for 1916 are not yet available. The following figures are, therefore, only approximate. The total production of concentrates for this year, including New Jersey and Tennessee, amounts to 1,280,000 tons. Of this tonnage, five mines produced approximately 536,000 tons, or about 42 per cent. The remaining concentrates came mainly from the "Valley States," Missouri, Wisconsin, Kansas, Oklahoma, and Arkansas. The 1,280,000 tons of concentrates represent about 25,000,000 tons of crude or run-of-mine ore. Of the five mines producing the 42 per cent., the dimensions of three are approximately 25 by 1500 by 2000 ft. (7.6 by 457 by 610 m.) or more: Four of the five mines are undoubtedly veins in the common acceptance of the term. They are located in great vein systems. The mines of "Valley States" have not, so far, been classed as veins; simply as "secondary deposits." The origin of these secondary deposits has been a warmly debated subject. Many geologists contend that they are the results of leaching from overlying and adjacent rocks carrying but traces of zinc, these traces leached out and deposited in favorable places. If this theory is correct, deposition is strictly limited to shallow depths. No volume of ore comparable to that of "true fissure veins" is to be expeeted. Just what this means to the future of zinc mining in these States is here indicated. The total zinc-bearing areas of these States amount to about 9124 sq. miles (23,631 sq. km.). Assuming that 10 per cent. of this total will be more or less productive, there are 912 sq. miles (2,362 sq. km.) of "mineral" ground. The average depth of the operated mines is something like 100 ft. or less. In Bulletin 606, U. S. Geological Survey (1915), p. 202, Siebenthal makes the following statement: "The writer is informed by William Waugh, one of the drillers of the Stone City well, that cuttings from other wells which he drilled in the vicinity of Pittsburgh, Kan., have shown galena and sphalerite taken from a depth of 591 ft. (180.14 m.) and that the showing of ore at some places would be considered good enough to justify the sinking of a shaft had it been found in the Joplin district and at shallower depths." Leaving out of the question the prohibitive cost of such a shaft, there is

Jan 1, 1918

By C. E. Mills

The Verde mining district is in Yavapai County, in north-central Arizona. Jerome, the principal town, has a population of 6000 and the two important mines of the district—the United Verde and the United Verde Extension—lie almost within its limits. Perched high on the southwest side of the Verde valley, at elevations of 4800 and 5500 ft. (1463 and 1676 m.) respectively, both mines have long tunnels from their lower levels through which the ore is hauled to the smelters. Clarkdale, the smelter town for the United Verde mines, lies in the Verde valley 4.1 miles (6.5 km.) distant in an air line from Jerome and at an elevation of 3560 ft. The two towns are connected by the standard-gage railroad of the Verde Tunnel and Smelter R. R., a subsidiary of the United Verde Copper Co. This road is 11 miles long and has a compensated grade of 4 per cent. At Clarkdale it connects with the Verde valley branch of the Santa Fe railroad. Clemenceau, the smelter town for the United Verde Extension mine, lies 3.5 miles (5.8 km.) in a southeasterly direction from Clarkdale, at an elevation of 3420 ft. It is connected to the Verde Valley branch of the Santa Fe railroad at Clarkdale by the Arizona Extension R. R., a subsidiary of the United Verde Extension Mining Co. The portal of the haulage tunnel, at an elevation of 3757.5 ft., is also connected with the smelter town by 4 miles of standard-gage track belonging to the same company. In the vicinity of Jerome, the great southern escarpment of the Arizona plateau forms the northeast side of the Verde valley. The general level of this escarpment, or "rim" as it is called, is about 4000 ft. above the Verde River. A corresponding elevation is reached only by the highest peaks of the Black Hills, which bound the valley to the southwest. Two lava-capped mesas, known as "Mingus" and "Woodchute mountains," form the culmination of the Black Hills. That part of the Old Black Hills mining district which lies between their crests and the Verde River is now known as the Jerome, or Verde, mining district. If the smelter towns are not included, a strip about 7 miles long by 3 miles (11 by 5 km.) wide, embraces practically all of the properties belonging to the Jerome district. T-bis strip lies parallel to and along the side of the Verde valley from First View, 2 miles northwest from Jerome, to the

Jan 1, 1925

By H. C. Burghard, F. R. Brotzen

Experiments were performed to determine the effects of mechanical vibrations on ordering in CuAu. The effects of 5, 10, and 15 kc vibrations were investigated over a range of ordering temperatures of 280° to 360°C. A decrease in the rate of ordering was observed at all frequencies and ordering temperatures. THE effects of mechanical vibrations on certain solid-state reactions have been noted by several investigators. In 1930, Mahoux' reported a substantial increase in the case depth of a steel sample nitrided under the influence of mechanical vibrations over that of an unvibrated sample. Similarly, an accelerating effect of vibrations on the diffusion of chromium in steel was noted. Guillet, in the same year, confirmed the results of Mahoux. More recently Schenck and schmidtmann3 studied the effects of low-frequency, alternating loads on the diffusion of carbon in steel. The results of their experiments, conducted at 500 cycles per min and large strain, (0.2 pct), indicated an acceleration of the process. These workers also reported an increase in case depth of a sample vibrated at 430 kc during a carburizing treatment. Effects of high-frequency vibrations on solid-state reactions have also been investigated by Gudzoff and Gavze6 and Fairbanks and Dewez.7 The former reported an acceleration of the age-hardening process in aluminum alloys. The latter noted changes in the structure and mechanical properties of steel annealed under the influence of vibrations. On the other hand, Altenburg4 and Ehringer5 have given some theoretical reasons and experimental evidence as to the improbability of any effect of vibrations on diffusion. Comprehensive surveys of the effects of vibrations on metallurgical reactions are given by Hiedemann' and Bergmann.9 None of the above investigations led to a physical description of the effects of mechanical vibrations on solid-state reactions. In the present study an attempt was made to gain an understanding of the influence of vibrations on nucleation and diffusion. The order-disorder transformation was chosen for investigation since its mechanism has been extensively discussed in the literature. Moreover, the progress of the transformation may be easily followed by observation of electrical resistance changes. EXPERIMENTAL PROCEDURE The specimens used for the experimental observation of ordering rates were prepared from 50 at. pct Cu-Au alloy wire.* Each specimen consisted of a 0.02-in. diam wire approximately 10 in. long to which two copper potential leads were silver soldered, 2 1/2 in. apart, near one end of the wire. A 1/8-in. diam by 1/4-in. long steel stub was silver soldered

Jan 1, 1960

By Frank E. Hauser, Philip R. Landon, John E. Dorn

The flow and fracture strengths of polycrystalline aggregates of high purity magnesium and a solid solution of aluminum in magnesium were determined as functions of temperature and grain size. Magnesium was found to obey two distinct fracture laws. Over the high temperature range, the fracture stress decreased with increasing test temperatures in a manner that closely paralleled the flow stress-temperature relationship. However, over the low temperature range, the fracture stress was independent of the test temperature though highly dependent on grain size, following the trend that is typical for the low temperature brittle fracturing of polycrystalline aggregates of body-centered-cubic and close-packed-hexagonal metals. Even at 78°K, however, plastic strains of 1 to 7 pet were obtained preceding onset of brittle fracturing. Over the brittle fracture range of temperatures, the fracture stress increased linearly with the reciprocal of the square root of the mean grain diameter, while over the entire range of temperatures investigated, the flow strength was observed to increase linearly with the reciprocal of the square root of the mean grain diameter. PREVIOUS investigations', 'have shown that deformation of coarse grained aggregates of high purity magnesium is interrupted by fracturing at very small strains. Such tendency toward brittle fracturing increased with increasing grain size and decreasing test temperature. In several respects, however, low temperature fracturing of magnesium appeared to differ from the truly brittle type exhibited by zinc, molybdenum, tungsten, and iron, so often characterized as a cleavage mode of fracturing. The absence of a well-defined cleavage mechanism for fracturing and the fact that some plastic deformation precedes fracturing might suggest that magnesium does not exhibit the same kind of brittle fracturing that is common to body-centered-cubic metals and to other close-packed-hexagonal metals. But, as will be shown, the low temperature fracture laws for magnesium are analogous to those that apply to iron, molybdenum, tungsten, and zinc in spite of differences in mechanisms and in plastic strains to fracture. In view of these observations. the low temperature fracturing of magnesium will also be called brittle fracturing. This, of course, does not imply that the brittle fracturing of metals is synonymous with the brittle fracturing of glass or other nonmetallics. Whereas the brittle fracturing of glass probably obeys Griffith's law, the low temperature brittle fracturing of metals arises from stresses induced by a series of dislocations piled up at an opaque grain boundary. Experimental Results All tests were made on tensile bars having gage sections that were 2 in. long and 0.375 or 0.25 in. wide. In order to develop a series of grain sizes, the

Jan 1, 1957

By Herbert H. Kellogg, Hugo Vasquez- Rosas

Recently the long-chain primary amines have been used extensively for the flotation of silicate minerals. The use of amines to float sulphide minerals has been investigated by several authorsl-5-l8 but most of this work has been done with the short-chain (less than six carbon atoms) primary amine compounds or the more expensive secondary, tertiary and quaternary amines. Perhaps the fact that the long-chain amines are good collectors for the common gangue minerals has led investigators to omit them from consideration as collectors for the selective flotation of metallic sulphides. The work reported in this paper was designed to investigate the use of a typical long-chain amine salt, laurylamine hydro-chloride, as a collector for the flotation of galena-sphalerite ores. The results show that laurylamine hydrochloride (LAmHCl), when used in small amounts, is a good collector for the selective flotation of sphalerite and galena from the common gangue minerals. The differential flotation of sphalerite from galena was not accomplished but the amine flotation of sphalerite after the standard xanthate flotation of galena is possible. The experimental work reported herein is not complete enough to be able to say whether amine flotation of lead-zinc ores would prove superior to xanthate flotation, or whether the method is even applicable to a more complex ore than the one used for this work. However, the apparent reagent costs for the flotation operations described in this paper seem to be less than for xanthate flotation. This fact alone should be sufficient to encourage the millman to investigate the use of these amine reagents, especially as these reagents are available on a commercial scale at a reasonable price. This paper has as its secondary purposes to illustrate how contact-angle measurements have aided in this investigation, and to bring forward some evidence concerning the mechanism of the collecting action of primary amines. Contact-angle Tests The contact-angle measurements were made by the method described by del Giudice6 and used in recent work by Taggart and his collaborators.7-9 The mineral specimens for the contact-angle tests were carefully chosen, to avoid cracks and inclusions of other minerals. All specimens were mounted in "transoptic" plastic mounts and the surfaces were cleaned by polishing with levigated alumina on a cloth-coverkd glass polishing wheel. Distilled water was used on the lap during the polishing and at all subsequent steps in the contact-angle tests. The mounted mineral specimens were handled with glass forceps and special care was exercised to prevent exposure of the clean surface to air or any other source of contamination.

Jan 1, 1947

By Herbert H. Kellogg, Hugo Vasquez- Rosas

Recently the long-chain primary amines have been used extensively for the flotation of silicate minerals. The use of amines to float sulphide minerals has been investigated by several authorsl-5-l8 but most of this work has been done with the short-chain (less than six carbon atoms) primary amine compounds or the more expensive secondary, tertiary and quaternary amines. Perhaps the fact that the long-chain amines are good collectors for the common gangue minerals has led investigators to omit them from consideration as collectors for the selective flotation of metallic sulphides. The work reported in this paper was designed to investigate the use of a typical long-chain amine salt, laurylamine hydro-chloride, as a collector for the flotation of galena-sphalerite ores. The results show that laurylamine hydrochloride (LAmHCl), when used in small amounts, is a good collector for the selective flotation of sphalerite and galena from the common gangue minerals. The differential flotation of sphalerite from galena was not accomplished but the amine flotation of sphalerite after the standard xanthate flotation of galena is possible. The experimental work reported herein is not complete enough to be able to say whether amine flotation of lead-zinc ores would prove superior to xanthate flotation, or whether the method is even applicable to a more complex ore than the one used for this work. However, the apparent reagent costs for the flotation operations described in this paper seem to be less than for xanthate flotation. This fact alone should be sufficient to encourage the millman to investigate the use of these amine reagents, especially as these reagents are available on a commercial scale at a reasonable price. This paper has as its secondary purposes to illustrate how contact-angle measurements have aided in this investigation, and to bring forward some evidence concerning the mechanism of the collecting action of primary amines. Contact-angle Tests The contact-angle measurements were made by the method described by del Giudice6 and used in recent work by Taggart and his collaborators.7-9 The mineral specimens for the contact-angle tests were carefully chosen, to avoid cracks and inclusions of other minerals. All specimens were mounted in "transoptic" plastic mounts and the surfaces were cleaned by polishing with levigated alumina on a cloth-coverkd glass polishing wheel. Distilled water was used on the lap during the polishing and at all subsequent steps in the contact-angle tests. The mounted mineral specimens were handled with glass forceps and special care was exercised to prevent exposure of the clean surface to air or any other source of contamination.

Jan 1, 1947

By R. E. Reed-Hill, W. H. Hartt

The "(3034) " twin lamellae in magnesium have been reexamined using electron microscope replicas. The double twinning sequence (1011)- (1012) for these lamellae has been reconfirmed. Evidence is presented showing that the irrational habit of these twins is probably the direct result of a need to accommodate the second-order twinning shear. This accommodation vesults in both an external shear in the matrix and an internal shear in the lamella. A model is presented which accounts for the experimental obseruations. HCP metals are generally characterized by strong textures in which the basal planes of the grains tend to be aligned parallel to the rolling direction in sheet or plate and to the axis of wires and rods. Since these directions are normally those in which finished products may be subjected to uniaxial tensile stress, these textures effectively place the crystals of magnesium objects in orientations unfavorable to both basal slip and {1012) twinning, the easily activated deformation systems of this metal. However, when magnesium crystals are deformed near room temperature by a tensile stress nearly parallel to the basal plane, another mode of deformation can occur.',2 This is _a double twin which forms first by twinning on {loll), followed by retwinning on (1012). The resulting twin lamellae are of considerable interest. First, they can be responsible for "brittle fracture''; when a tensile stress axis lies in the basal plane, because the reoriented crystal structure of a lamella is well-aligned for slip while the parent crystal is not. Extensive internal deformation may thus occur while the matrix is still almost undeformed. This deformation can produce a ductile rupture running the length of the twin.3 Complete failure of the specimen may then oc-cure by the spreading of cracks from one twin lamella to another, or by the movement of a crack into a grain boundary and then along grain boundaries. Since the the volume fraction of these doubly twinned elements is normally very small, the fracture may be classed as brittle, although the fracture mechanism is, of itself, essentially ductile. It is quite probable that the ductility transition, normally observed4 in magnesium at or slightly Obove room temperature, is closely associated with these second-order twins. The detailed relationship of these twins to fracture in single crystals will be the topic of another paper. The present paper is concerned with a second important aspect: the irrational habit of these double twins that falls close to {3034), or approximately 7 deg away from the primary (10il) twin habit. There is good reason to believe that this habit results directly

Jan 1, 1968

By R. F. Mehl, C. S. Barrett, A. H. Geisler

THE complicated nature of the property changes that accompany age-hardening has made it necessary to reconsider and to elaborate the simple dispersion theory.1 It has been apparent for some time that more direct information is needed concerning the atomic mechanism of precipitation from solid solution if the theory of age-hardening is to be developed past a purely qualitative stage.‡ Fortunately, in recent years information has been developed which allows us to trace in detail the lattice changes accompanying the process of precipitation from solid solution. This information relates chiefly to the sequence of the several stages of lattice alteration by which the matrix lattice is transformed to the equilibrium precipitate lattice, and permits reasonable inferences to be drawn concerning the states of internal strain that accompany these stages. This information is most complete for the solid solution of copper in aluminum. The equilibrium precipitate is the ?' phase," CuA12." This forms in plates, parallel to the {100} matrix planes. The atom pattern and atom spacing on the plane in ?' lying parallel to this plane are roughly similar to those opposite it in the matrix.' The formation of ?', however, is preceded by the formation of a transition lattice ?', which again lies parallel to the matrix {100} plane, but in this case the matching of atom pattern and spacing across the matrix-precipitate interface is nearly perfect; thus there is lattice coherency across the interface and the interface is a plane of separation in only a very limited sense.4-8 Particles of ?' may be recognized microscopically and form a well-defined Widmanstätten figure.* The ?' lattice is recognized by the occurrence of diffraction lines on powder photograms or of spots on Laue photograms which may be analyzed in the usual ways to determine the lattice type and the lattice spacings. Very recent research 6.7,1 has shown, however, that streaks occur on the Laue photogram at an earlier point in time during the aging process. These streaks have been attributed to a preferential clustering of copper atoms into small platelike elements of only a few atoms in thickness and a few hundred atoms in diameter, probably of the composition of "CuA12," which may be designated as Guinier-Preston zones or aggregates.1 It is difficult if not impossible to determine the lattice type and lattice spacing in these aggregates. It is possible1 that these aggregates are in fact merely ?' in a high state of dispersion; the inclination to argue this is strong, as we shall see later. Never-

Jan 1, 1941

By E. C. Houston

The presence in the Tennessee Valley of extensive deposits of olivine, a silicate of magnesium and iron that contains approximatcly 28 per cent magnesium, has been recognized since 1896 when Lewis8 published a survey of basic magnesium rocks of western North Carolina. A recent field survey by T.V.A.7 showed that more than two hundred million tons of high-grade olivine occurs above local drainage levels in western North Carolina and northern Georgia. Except for sporadic attempts to work the olivine for its nickel and chromium contents,10 the ore received little attention industrially until 1926 when Goldschmidt3 suggested its use in the manufacture of refractories. Only one instance is recorded of an attempt to utilize the ore commercially for its magnesium content;11 in this case a process was used in which olivine was treated with sulphuric acid, the resultant mixture was leached with water, and the leach solution was purified and evaporated to form epsom salts, which was the end product. As a part of its program of contributing to the development of the natural resources of the region, the Tennessee Valley Authority became interested in the olivine deposits as a source of metallic magnesium because of their high magnesium content and proximity to hydroelectric power. Studies were undertaken to determine the feasibility of producing magnesium chloride by extraction of olivine. The experimental work was carried out successively at the T.V.A. Minerals Testing Laboratory, Norris, Tenn., at the Georgia State Engineering Station,* Atlanta, Ga., and at the T.V.A. laboratory at Wilson Dam, Ala. The present paper describes a process, developed through the pilot-plant stage, whereby magnesium chloride suitable for reduction to metallic magnesium can be prepared from olivine by extraction with hydrochloric acid and subsequent purification. Research on the magnesium-from-olivine process, originally intended for peacetime use, was given impetus by the shortage of magnesium that existed at the beginning of the current world war. By the time the process was sufficiently developed to justify a proposal for its inclusion in the war program, the shortage had been met by expansion and development of other processes. However, it is believed that the magnesium-from-olivine process may have advantages that will warrant consideration of its use after the war, when the. economics of the various processes rather than production on a wartime scale will be the criterion for commercial production of magnesium. Description of Process Metallic magnesium is produced electro-lytically by the Dow and the Elektron

Jan 1, 1948

By E. C. Houston

The presence in the Tennessee Valley of extensive deposits of olivine, a silicate of magnesium and iron that contains approximatcly 28 per cent magnesium, has been recognized since 1896 when Lewis8 published a survey of basic magnesium rocks of western North Carolina. A recent field survey by T.V.A.7 showed that more than two hundred million tons of high-grade olivine occurs above local drainage levels in western North Carolina and northern Georgia. Except for sporadic attempts to work the olivine for its nickel and chromium contents,10 the ore received little attention industrially until 1926 when Goldschmidt3 suggested its use in the manufacture of refractories. Only one instance is recorded of an attempt to utilize the ore commercially for its magnesium content;11 in this case a process was used in which olivine was treated with sulphuric acid, the resultant mixture was leached with water, and the leach solution was purified and evaporated to form epsom salts, which was the end product. As a part of its program of contributing to the development of the natural resources of the region, the Tennessee Valley Authority became interested in the olivine deposits as a source of metallic magnesium because of their high magnesium content and proximity to hydroelectric power. Studies were undertaken to determine the feasibility of producing magnesium chloride by extraction of olivine. The experimental work was carried out successively at the T.V.A. Minerals Testing Laboratory, Norris, Tenn., at the Georgia State Engineering Station,* Atlanta, Ga., and at the T.V.A. laboratory at Wilson Dam, Ala. The present paper describes a process, developed through the pilot-plant stage, whereby magnesium chloride suitable for reduction to metallic magnesium can be prepared from olivine by extraction with hydrochloric acid and subsequent purification. Research on the magnesium-from-olivine process, originally intended for peacetime use, was given impetus by the shortage of magnesium that existed at the beginning of the current world war. By the time the process was sufficiently developed to justify a proposal for its inclusion in the war program, the shortage had been met by expansion and development of other processes. However, it is believed that the magnesium-from-olivine process may have advantages that will warrant consideration of its use after the war, when the. economics of the various processes rather than production on a wartime scale will be the criterion for commercial production of magnesium. Description of Process Metallic magnesium is produced electro-lytically by the Dow and the Elektron

Jan 1, 1948

By G. W. Cullen

Niobium-tin has been prepared on insulating suhstrates hby simultaneous hydrogen reduction of gaseous niobium and tin halides. Stoichiometric material is greater than 98.8pct theoretical density, appears to he single-phase, and has a total impirity level less than 0.3 at. pct. Transition temperatures and lattice constants may he related to composition. Typical current densities in various fields and orientations are given. IT is known that Nb3Sn carries large current densities in high fields, 1 and exhibits an unusually high transition temperature2 and critical field.3 For these reasons high-field solenoids have been constructed of this material.4 Because of the emphasis on solenoid fabrication, much of the materials research has been directed toward development of wire geometries wherein the brittle Nb3Sn is supported by a more malleable metal or alloy. There are, however, basic studies and applications that can be carried out only on Nb3Sn supported by an insulator. Insulating substrates are desirable for a number of reasons: the substrate does not interact with applied or induced currents and fields; diffusion of metallic species into the de- posit is avoided, both during the preparation and during subsequent heat treatment; irradiated samples are not more active than the deposit itself. Unsupported Nb3Sn geometries may also be prepared by preferential chemical dissolution of the insulating substrate. This report describes the preparation and properties of Nb3Sn deposits on ceramic substrates. Experiments currently utilizing material prepared in the manner described in this report include the following: dependence of current-carrying properties on field strength and orientation 5,6 radiation damage,7,8 tunneling,9 thermal conductivity (substrate removed),1° microwave surface impedance," tube magnetization,6,12 resistivity as a function of temperature,13 and current density and transition temperature as a function of annealing.14 Possible practical applications include magnetic shielding, superconductor generators, and frictionless bearings. PREPARATION Methods for the deposition of elemental niobium and tin by hydrogen reduction of the gaseous metal halides have been known for some time,15,18 but only recently a procedure was developed in this laboratory17 for the codeposition of these two metals on a hotwire as the intermetallic compound, Nb3Sn. This method of simultaneous hydrogen reduction of the gaseous niobium and tin chlorides is used for the preparation of Nb3Sn On ceramic substrates. The procedure differs from that employed on a hot wire in that insulating substrates cannot conveniently be heated to temperatures greater than their surround-

Jan 1, 1964

By E. C. Houston

THE presence in the Tennessee Valley of extensive deposits of olivine, a silicate of magnesium and iron that contains approximately 28 per cent magnesium, has been recognized since 1896 when Lewis8 published a survey of basic magnesium rocks of western North Carolina. A recent field survey by T.V.A 7 showed that more than two hundred million tons of high-grade olivine occurs above local drainage levels in western North Carolina and northern Georgia. Except for sporadic attempts to work the olivine for its nickel and chromium contents,10 the ore received little attention industrially until 1926 when Goldschmidt3 suggested its use in the manufacture of refractories. Only one instance is recorded of an attempt to utilize the ore commercially for its magnesium content;" in this case a process was used in which olivine was treated with sulphuric acid, the resultant mixture was leached with water, and the leach solution was purified and evaporated to form epsom salts, which was the end product. As a part of its program of contributing to the development of the natural resources of the region, the Tennessee Valley Authority became interested in the olivine deposits as a source of metallic magnesium because of their high magnesium content and proximity to hydroelectric power. Studies were undertaken to determine the feasibility of producing magnesium chloride by extraction of olivine. The experimental work was carried out successively at the T.V.A. Minerals Testing Laboratory, Norris, Tenn., at the Georgia State Engineering Station,* Atlanta, Ga., and at the T.V.A. laboratory at Wilson Dam, Ala. The present paper describes a process, developed through the pilot-plant stage, whereby magnesium chloride suitable for reduction to metallic magnesium can be prepared from olivine by extraction with hydrochloric acid and subsequent purification. Research on the magnesium-from-olivine process, originally intended for peacetime use, was given impetus by the shortage of magnesium that existed at the beginning of the current world war. By the time the process was sufficiently developed to justify a proposal for its inclusion in the war program, the shortage had been met by expansion and development of other processes. However, it is believed that the magnesium-from-olivine process may have advantages that will warrant consideration of its use after the war, when the economics of the various processes rather than production on a wartime scale will be the criterion for commercial production of magnesium. DESCRIPTION OF PROCESS Metallic magnesium is produced electrolytically by the Dow and the Elektron

Jan 1, 1945

By C. Ernest Birchenall, Robert F. Mehl

Application of diffusion laws in the customary form to experimental studies in binary metallic solid solutions has shown the diffusion cocfficient to vary with concentration for all systems investigated. The factors determining this variation have not been ascertained. However, the question of whether the diffusion coefficient would become a constant, independent of concentration throughout a single phase if the concentration gradient in the diffusion equation were replaced by an activity gradient has been an attractive subject for speculation. Wagner¹ derived an expression for the force acting on a diffusing particle in terms of the chemical potential. This was also the approach chosen by Jost2 in his monograph. From a somewhat different point of view, Eyring3 and his co-workers have used activity gradients when dealing with diffusion in concentrated nonideal solutions. The only actual test with experimental data is that given by Darken,4 though this is more qualitative than quantitative. Many others opposed the application in any way of thermodynamic concepts to kinetic phenomena, including diffusion processes. A rigorous examination of this principle requires good data expressing the relationship between activity and concentration for solid solutions for which reliable diffusion work has been done. The literature provides such information only for the interstitial solution of carbon in gamma iron (austenite) and for the substitutional copper-zinc solutions (alpha brass). Activity data for carbon in austenite at 800°C and 1000°C are available from the recent work of Smith5 on the equilibrium of hydrogen-methane and carbon monoxide-carbon dioxide mixtures with gamma iron. Combining these with the diffusion studies of Wells and Mehl6 makes possible a quantitative test for this interstitial solid solution. The vapor-pressure determinations for zinc over brass by Hargreaves7 allowed the calculation of activities in this system over a wide range of temperatures and concentrations. Extensive investigation of diffusion in this substitutional solid solution has been carried out by Rhines and Mehl.8 Activities in Brass9 If the vapor phase of zinc is assumed to behave as an ideal gas, any solid or liquid solutions that are in equilibrium with the same partial pressure of zinc at the same temperature have the same thermodynamic activity of zinc. In order to assign a numerical value to the activity azn, it is necessary to choose some standard reference state to which an activity value of unity is arbitrarily assigned. It is customary to choose the liquid or solid state of the pure material. Then azn is defined numerically by

Jan 1, 1947