Search Documents

By W. H. Somerton

The effects of drilling variable on rotary drilling rates and efficiencies have been studied by a series of laboratory drilling tests. TWO-cone 1.25-in. diameter hits were used to drill vertically upwards into rock samples at corltrolled weights and rates of rotation. Shale, sandstone and specially prepared concrete samples were used in this study. Power input to the ririllirig systeln was measured and drilling chips collected for energy — .size reduction studies. Reasouably good correlations between drilling variables and rates of penetrotion were found. Qrrantities that are difficult to evaluate include rock strength parameters and the effects of bit wear. Effects of bit size and geormetry require further investigation. Analysis of the drilling chips confirmed the premise that, for rocks containing two or more mineral constituents of diflerent strengths, a greater amourrt of rock breakage occurs in the weaker constituent. Drilling conditions which required greater amounts of energy produced finer drilling chips. As bit tooth wear progressed, drilling chips became finer. Efficiency of rotary drilling as a rock breakage mechanism was extremely low. Comparison was made with theoretical energy requirements and with energy requirements for size reduction by comminution methods. INTRODUCTION Many technological developments and innovations have made possible the successful drilling of oil wells by the rotary method to depths exceeding 20,000 ft. Bigger, more powerful rigs, better steels, improved bit design and more careful control of the circulating system have all contributed to this success. Despite these advances comparatively little is known regarding the basic mechanism of rock breakage by the rotary drilling process. Future improvements and, in particular, reduction of drilling costs will undoubtedly require a clearer understanding of the variables controlling effectiveness and efficiency of rotary drilling. Rotary drilling is inherently an inefficient means of producing rock breakage. Loss of energy in transmission from the surface to the cutting mechanism may be large, thus limiting the total amount of energy which may be applied to rock breakage. Increased efficiency may be realized by improved energy transmission methods such as the turbodrill. Conversion of transmitted energy to rock breakage by use of rotating cutter teeth is likewise inefficient. Improvement of cutter efficiency has been obtained essentially by empirical means —changes in bit tooth size, shape and spacing, and tooth deletion to give clean bottom-hole patterns. The present work was undertaken to investigate the factors controlling rates of bit penetration under laboratory drilling conditions. Laboratory drilling apparatus is shown in Fig. 1. The effects of rock strength and bit wear on drilling rates were investigated. Drill cuttings were analyzed to determine the character of breakage and to compare this with other methods of producing rock breakage. VARIABLES INVOLVED IN ROTARY DRILLING Some of the variables controlling bit penetration rates can be studied conveniently by dimensional grouping. R/DN f(F/D2S) or

By H. H. Keller, E. J. Couch

Damage to production wells subjected to the high temperatures associated with in-situ combustion projects has been a problem since the advent of this thermal recovery technique. Injection of water down the annulus of hot wells has been successfully utilized for cooling and prolonging the life of such wells. A mathematical model that is suitable for predicting the effectiveness of cooling water in a particular application is developed. Typical results for practical ranges of the various parameters involved are presented. INTRODUCTION In the normal course of in-situ combustion operations, highly damaging conditions develop in the production wells as the combustion zone approaches, and these wells are subjected to high temperatures (up to 1500F). The resulting well damage is recognized as one of the more serious operating problems unique to the in-situ combustion process. Even in operations where well completions have been specifically designed to cope with this problem, the question arises as to how this destructively high temperature can be kept within tolerable limits. A simple and economical approach to this problem is to circulate cooling water down-hole. This method has been used with some success in shallow reservoirs. At greater depths, however, the heat exchange with the overburden surrounding the well and between the fluids in the tubing and the annulus tends to equalize the temperatures of the two fluid streams so that the cooling capacity delivered to the bottom of the hole decreases with well depth. This method would provide no appreciable control over the bottom-hole temperature at great depths. In order to delimit the condition under which cooling by water circulation is effective, the wellbore temperature must be related to the water inlet rate and temperature; to the reservoir depth, production rate, and initial temperature; and to the combustion at at bot tom-hole depth. A model that meets these requirements and that will offer an approach for developing engineering solutions to practical design and operating problems is described in this paper. MATHEMATICAL MODEL Previous studies of temperature distributions include those for flowing wells1p2 and those for hot fluid injection. Adams and Haddenhorst 6 presented solutions for the down-hole circulation of hot oil in the treatment of paraffin-deposition problems. In this paper the thermal model presented by Ramey 4 is adapted to the flow system shown schematically in Fig. 1. Water at temperature Ti is injected at a rate wi and flows down the annulus outside the tubing. It mixes at bottom-hole depth D with the fluids produced at race w from the hot reservoir at temperature T. This mlxtureJ. of injected water and reservoir fluids flows up the tubing and is produced at the surface at TI,. In order to describe the temperature response in this system, we make use of the usual conservation of

Jan 1, 1969

By Robert B. Sosman

THE relative temperature distribution within a coke oven and among the ovens in a battery can be obtained automatically for the operator's guidance by sighting a total-radiation pyrometer on the face of the coke as it is pushed out, and recording the surface temperature. Keeping the instrument clean and keeping its view of the coke unobstructed by smoke and dust are the principal problems. Typical records from three plants are presented in this paper, showing that the temperature patterns are reproducible. DEVELOPMENT OF METHOD The method of coke pyrometry described in this paper was introduced in 1936 by E. A. Lee, then Assistant Superintendent, now Superintendent, of the Coke Plant at Lorain Works, National Tube Co., Lorain, Ohio. At the request of the Coke Committee of the United States Steel Corporation, the Research Laboratory of the Corporation undertook to adapt the method to the somewhat different conditions met with at the Gary Works of the Carnegie-Illinois Steel Corporation, Gary, Ind., and at the Clairton Works of the same Corporation at Clairton, Pa. This work was done in cooperation with the Leeds and Northrup Co. of Philadelphia and later with the Brown Instrument Co. Division of Minneapolis-Honeywell Regulator Co., Philadelphia. We of the Research Laboratory wish to express our appreciation of the courtesies extended by Mr. Lee, by A. N. Cole, Superintendent of the Gary coke plant, and by D. P. Finney, Assistant General Superintendent in charge of coke-plant operations at Clairton. We are also indebted to the instrument companies for the loan of a part of the equipment. At Gary and Clairton the instruments were installed and various experiments were made by J. W. Bain, of the Research Laboratory of the United States Steel Corporation. PYROMETRY OF COKE The coke inside a by-product oven is almost completely inaccessible to pyrometric instruments. The temperature in the walls can conceivably be measured with thermocouples, but the atmosphere is usually strongly reducing, a condition well known to be destructive to the accuracy of the customary high-temperature couples. In some plants, periodic readings are taken with an optical pyrometer sighted into the top of the combustion flues. This is a useful measure for safety and general control, as it tends to prevent the damage that would result from overheating of the ovens. It does not, however, tell much about the temperature of the coke itself, because of the continually changing gradient in the wall between the coke and the combustion chamber. The best indication of the temperature of the coke itself must therefore be obtained by observation of the product as it is pushed out of the oven. The human eye is very sensitive to variations in brightness of a surface, and particularly to differences in brightness over a continuous hot surface.

Jan 1, 1942

By J. W. Spretnak, V. Kandarpa, G. W. Powell, R. A. Erickson

Neutron-diffraction pattens were obtained at room temperature from two austenitic manganese steels, oxc wth n carbon content of 1.23 zct PC/ and the olher 0.63 wt pct. Analysis of the data showed that the curOan atols (ions) occupy tile octaheadral site. any of the cavbon is in the tetahedral site, tile concentration is too strzall lo be detecled by tzeulr-on d$facton. AS part of a long-range investigation of eutectoid decomposition, a study of the structure of austenite has been undertaken in order to characterize as best as possible the parent phase in the Fe-C system. Austenite is a solid solution of carbon atoms in fcc iron, the carbon atoms being located in interstitial positions. Of the two kinds of interstitial sites, octahedral (0, +, +) and tetrahedral (4, a, $), in this lattice, the larger octahedral sites are usually considered as the probable position of carbon. The strain energy involved in pytting a neutral carbon atom (covalent di; ameter 1.54)' into a tetrahedral site (diameter 0.56A) is considerably greater than that associated with p2tting carbon into the octahedral site (diameter 1.08A). Dayal and arkeen' observed the migration of carbon in iron under the influence of an electric field indicating tha tye carbon is ionized. pe ionic radius of C'4 is 0.15A and that of C" is 0.29. Consequently, it is conceivable that carbon ions could occupy the tetrahedral sites if one considers only the strain energy. Size considerations alone do not provide a complete explanation for the formation of the interstitial solid solutions, however. because metals such as copper, zinc, and cadmium do not appear to form interstitial solid solutions in spite of their large interstitial sites. Evidence which suggests partial ioni-zation of the carbon in austenite has also been obtained by Speiser, Spretnak, and alor who derived formu- lae relating the observed change in lattice parameter to the effective diameter of the solute atom. Assuming the carbon occupies the octahedral site. they computed the effective diameter of carbon to be 1.33A whereas the covalent diameter is 1.54A. petch5 concluded from powder X-ray diffraction experiments that carbon atoms occupy the octahedral sites. His conclusion was based on the general trend observed in the intensity of the diffraction lines as the carbon content of the austenite was increased. However, the major difficulty associated with application of X-ray diffraction to this particular problem is the relatively poor scattering power of carbon. Williamson and smallman' utilized X-ray diffraction to study the line broadening caused by the strain field about carbon atoms inferrite: these investigators concluded that at least 85 pct of the carbon in ferrite occupies the octahedral (0: 3, B) site rather than the larger

Jan 1, 1967

By J. J. Arps

This paper reviews the methods currently in use for estimating primary oil reserves and discusses the principles on which these methods are based. Particular emphasis is placed on how these methods change with the type of information available during the life cycle of an oil property. This paper contains various novel estimating methods and shortcuts heretofore unpublished. INTRODUCTION Estimating oil reserves is one of the most important phases of the work of a petroleum engineer since the solutions to the problems he deals with usually depend on a comparison of the estimated cost in terms of dollars, with the anticipated result in terms of barrels of oil. His recommendations to management regarding the best course of action are therefore normally based on the most favorable balance between these two. Specific engineering problems which require such a knowledge of recoverable oil reserves and a projection of future rates are: [a.] the exploitation and development of an oil reservoir; [b.] the construction of gasoline plants, pipelines and refineries; [c.] the division of ownership in unitized projects; [d.] the price to be paid in case of a sale or purchase of an oil property, and the magnitude of the loan which it will support; [e.] the proper depreciation rate for the investment in oil properties; and [f.] evaluation of the results of an exploration program. This discussion will be confined to the various methods and tools which are currently in use for estimating oil reserves to be obtained during the primary phase of an oil-producing reservoir and for a projection of the future production rates. Reserves which may be obtained by secondary recovery methods or fluid injection programs and gas and gas condensate reserves will not be discussed in this paper. Unfortunately, reliable oil reserve figures are most urgently needed during the early stages when only a minimum amount of information is available. Management's interest in the oil recovery from a property—aside from its use for accounting purposes—usually declines when the property approaches its economic limit, just at the time when the reliability of the estimates is at its best. To illustrate this general idea a chart is presented (Fig. 1) showing the three periods in the life of an imaginary oil property. Time is shown on the horizontal axis, while the cumulative production and estimated ultimate recovery are plotted vertically. No particular units are used and this schematical chart is not to scale. During the first period, before any wells are drilled on a property, any estimates will of necessity be of a very general nature, based on experience from similar pools or wells in the same area, and usually expressed in barrels per acre. This will

Jan 1, 1957

By Ray Hammond Misener

THE purpose of this paper is to describe the installation of the pumping station on the 3314-ft. level of the Carlos Francisco mine of the Sociedad Minera Backus y Johnston del Peru, at Casapalca, Peru. However, so much preliminary work was necessary before the actual installation could be started that some of that work will be described briefly, in order to clarify the discussion of the main subject. The Sociedad Minera Backus y Johnston del Peru, a subsidiary of the Cerro de Pasco Copper Corporation, owns and operates a group of mines in the Casapalca district, of which the most important are the Carlos Francisco and the Aguas Calientes. These two mines, one mile apart, are connected on their 2100 and 2700-ft. levels. These are motor-haulage levels, equipped with 3 ½ -ton Baldwin-Westinghouse locomotives operating from a 260-volt d.c. overhead trolley. A 38-cu. ft. hopper-bottom car is used. Each mine has a 2 ½ -compartment, inclined (70°) winze shaft. The Aguas Calientes shaft, operating between its 2100 and 2900-ft. levels, is used only for men and materials; whereas the Carlos Francisco shaft, between the 1700 and 2700-ft. levels of that mine, is the main operating shaft for the district. All the ore from the Carlos Francisco and the Aguas Calientes mines is hoisted through the Carlos Francisco shaft. The ore produced in these mines is by-passed to the 2700-ft. level, where it is gathered by the electric trains, taken to the Carlos Francisco shaft and dumped into an ore pocket in front of the shaft. The ore is hoisted to the 1700-ft. level in 2-ton self-dumping skips and emptied into a 150-ton loading pocket. There it is loaded into electric trains and despatched to the concentrator through the Backus and Johnston tunnel, which is the main entry from Casapalca to all the mines in the Backus and Johnston group. DEVELOPMENT PROGRAM In 1934 the following development program was outlined for the Carlos Francisco and the Aguas Calientes mines: (1) to deepen the Carlos Francisco shaft from the 2700 to the 3400-ft. level, (2) to deepen the Aguas Calientes shaft from the 2900 to the 3300-ft. level, and (3) to connect the two shafts on the 3300-ft. level with a motor-haulage crosscut. Each mine was to be developed also on intermediate levels (2900 and 3100). The three levels were to be spaced 54 meters (177 ft.) floor to floor, measuring from the 2700-ft. level along the incline of the shaft. The Carlos Francisco mine, together with the section between it and the Aguas Calientes mine, produces 10,000 gal. of water per minute. A fault to the north

Jan 1, 1943

By H. H. Evinger, M. Muskat

A methoD of calculating productivity factors for oil, gas, and water systems in the steady state is presented as an illustration of the quantitative application of the fundamental data on the flow properties of heterogeneous fluid systems. While the numerical results of the calculations cannot be applied directly to field conditions, because they are based on permea-bility data for unconsolidated sands and involve specific assumptions regarding the nature of the reservoir fluids, the methods of analysis and interpretation should havc significance in considering certain specific field situations when the necessary field and laboratory data become available. Moreover, it is felt that even under the idealized conditions to which the numerical calculations refer they should serve to give at least the orders of magnitude of the effects of gas-oil ratio and connate water on observed productivity factors. Within the indicated limitations, the computations imply that the foregoing factors can explain only a part of the apparent discrepancy between the homogeneous fluid productivity factors and those obtained recently in field measurements on the West Coast. IntroductioN Sufficient laboratory research has been carried out in the last several years on the fundamental features of the flow of heterogeneous fluids through porous media to call for consideration of what can be done with this type of information. It has, of course, already led to a, much clearer general understanding of the mechanics of oil production. However, examples of the quantitative application of the results of such laboratory studies are few in the literature. part of the explanation for this fact lies undoubtedly in the lack of sufficient laboratory data relating to practical fluids and sand systems such as would occur ill actual oil reservoirs. However, unless it can be shown that if such data were obtained quantitative applications could be made, serious doubt may be cast upon the desirability of carrying on further extensive experimental research work on fluid flow. The purpose of this paper is to present one approach to the problem of quantitative application of laboratory data to practical field problems. Because the published results on the basic experiments with three-phase fluid systems in porous media are limited entirely to uncon-solidated sands, the numerical applications made here will not pertain directly to any actual field situation. However, they should serve to illustrate what could be done with fundamental laboratory data if they were extended to cover the field of consolidated sands. From this point of view, it is hoped it will serve to encourage further laboratory research on this problem. The particular application to be treated here relates to the calculation of the productivity factors for oil-gas-water systems in the steady state. This specific problem seems especially appropriate for discussion in view of the recent publication by Johnston1 of the results of produc-

Jan 1, 1942

By M. Muskat, H. H. Evinger

A methoD of calculating productivity factors for oil, gas, and water systems in the steady state is presented as an illustration of the quantitative application of the fundamental data on the flow properties of heterogeneous fluid systems. While the numerical results of the calculations cannot be applied directly to field conditions, because they are based on permea-bility data for unconsolidated sands and involve specific assumptions regarding the nature of the reservoir fluids, the methods of analysis and interpretation should havc significance in considering certain specific field situations when the necessary field and laboratory data become available. Moreover, it is felt that even under the idealized conditions to which the numerical calculations refer they should serve to give at least the orders of magnitude of the effects of gas-oil ratio and connate water on observed productivity factors. Within the indicated limitations, the computations imply that the foregoing factors can explain only a part of the apparent discrepancy between the homogeneous fluid productivity factors and those obtained recently in field measurements on the West Coast. IntroductioN Sufficient laboratory research has been carried out in the last several years on the fundamental features of the flow of heterogeneous fluids through porous media to call for consideration of what can be done with this type of information. It has, of course, already led to a, much clearer general understanding of the mechanics of oil production. However, examples of the quantitative application of the results of such laboratory studies are few in the literature. part of the explanation for this fact lies undoubtedly in the lack of sufficient laboratory data relating to practical fluids and sand systems such as would occur ill actual oil reservoirs. However, unless it can be shown that if such data were obtained quantitative applications could be made, serious doubt may be cast upon the desirability of carrying on further extensive experimental research work on fluid flow. The purpose of this paper is to present one approach to the problem of quantitative application of laboratory data to practical field problems. Because the published results on the basic experiments with three-phase fluid systems in porous media are limited entirely to uncon-solidated sands, the numerical applications made here will not pertain directly to any actual field situation. However, they should serve to illustrate what could be done with fundamental laboratory data if they were extended to cover the field of consolidated sands. From this point of view, it is hoped it will serve to encourage further laboratory research on this problem. The particular application to be treated here relates to the calculation of the productivity factors for oil-gas-water systems in the steady state. This specific problem seems especially appropriate for discussion in view of the recent publication by Johnston1 of the results of produc-

Jan 1, 1942

By F. J. Dunkerlery, V. Damiano, J. Fulton, F. Pledger

Grain-growth and recrystallization characteristics of a commercially pure zirconium prepared by the iodide process are reported. Grain growth from 640° to 800°C was continuous once initiated and obeyed D = kt". Recrystallization of zirconium occurred at temperatures of 450° to 550°C after deformations of 20 and 50 pct. Hardening from partially soluble inclusions prevented determination of the absolute rates of recrystallization, but the relative rates of recrystallization obtained are useful as a guide in fabrication practice. BASIC information needed as a guide in the hot and cold working and annealing of metals includes recrystallization and grain-growth data. A search of the literature revealed no such information for pure zirconium. This is a report of practical grain-growth and recrystallization results obtained for a commercial grade of pure zirconium on a project sponsored by the Office of Naval Research. In this work, isothermal grain-growth curves were obtained at five temperatures from 640" to 800°C inclusively; while recrystallization curves have been determined at 450°, 500°, and 550°C for the metal at the deformation levels of 20 and 50 pct. In addition to the usual variables of temperature, time, and deformation, distribution of the second phase found in all commercial grades of iodide zirconium is also treated as an important factor in these grain-growth and recrystallization studies. In conducting this work, two properties of zirconium were particularly pertinent in dictating experimental conditions. First, since zirconium undergoes a transformation from the a close-packed hexagonal form to the ß body-centered cubic form at 862°C, no recrystallization or grain-growth studies were made above 800°C. Second, because dissolved gases (oxygen, nitrogen and/or hydrogen) increase the hardness and lower the ductility of the solid metal, all annealing treatments in this investigation were carried out in vacuum or in a helium atmosphere. Materials and Methods The zirconium used in this investigation was prepared by the Foote Mineral Co. by deposition from its iodide. A spectrochemical analysis of the metal showed the following composition in weight pct: Hf, 2.1; Mg, 0.012; Fe, 0.035; Si, 0.095; Ti, 0.023; Al, 0.037; Mo, trace; Ni, trace; Cr, trace; Ca, 0.006. Conventional metallographic procedures involving hand polishing on wet metallographic papers, followed by final polishing on fine, levigated alumina on gamal cloth and a medium speed wheel were used throughout this investigation. Grain boundaries were revealed with modified Tucker's etch containing 20 parts glycerine, 2 parts hydrofluoric acid, and one part nitric acid. Grain-Growth Procedure: Three lots of zirconium, designated here as series A, B, and C were prepared for the grain-growth studies as follows: Series A was prepared by cold swaging the % in. as-deposited rod to a 3/16 in. final diameter, followed

Jan 1, 1952

By James E. Berryman

A method is presented for calculating the pressure depletion performance of a gas-condensate reservoir from the original reservoir fluid composition using the laboratory determined pressure-production history and retrograde liquid accumulation as guides. Equilibrium vaporization ratios for this calculation were modified from published data until the calculated dew point pressure and retrograde liquid accumulation agreed with the values observed in the laboratory. The calculated results are compared with the produced gas composition determined by low temperature analysis during constant volume laboratory experiments of pressure depletion behavior. This comparison shows that the calculation procedure is adequate for determination of gas phase composition. Data from field separation tests in low temperature separators are presented which verify the applicability of published equilibrium vaporization ratios for a wide range of separator conditions. INTRODUCTION A reliable prediction of the pressure depletion performance of a gas-condensate reservoir is necessary in determining reserves and evaluating field separation methods. The predicted performance is also used in planning future operations and studying the economics of projects for increasing liquid recovery. Because the flow of fluid in a volumetric gas-condensate reservoir is usually single phase flow, the pressure-depletion per-formake is primarily a function of the phase behavior of the reservoir fluid. The properties of a gas-condensate system of major importance are: (1) compressibility factor at reservoir temperature and pressure; (2) dew point pressure; (3) composition changes of the vapor phase with pressure depletion; (4) recovery of original in-place hydrocarbons at any pressure; and (5) retrograde condensate accumulation. These properties are most generally determined by a pressure depletion-type experiment on recombined separator gas and liquid samples in the laboratory. ldeally the pressure-depletion performance can be calculated from the composition of the original reservoir fluid if the reservoir temperature and initial pressure are known.1,2,3 It has been reported "... comparison of such computations with depletion-type ex-periments on recombined samples in the laboratory have yielded results that appeared to be entirely adequate.". The success of such calculations is determined by the equilibrium vaporization ratios chosen, especially those for the higher boiling point hydrocarbons. It is the purpose of this paper to present a method for computing the change in composition of the vapor phase during pressure depletion by production using laboratory determined properties of the system to guide the calculation and to illustrate the use of the method with data from the Cockfield "D" sand of Washington field, St. Landry Parish, La. Results of field tests and laboratory analysis are included. As a result of this reservoir fluid study, a cycling program has been evaluated, the fidd has been unitized, and the cycling started in July, 1956.

Jan 1, 1958

By Gerald A. Munson, Fremont F. Clarke

DURING recent years the use of lithium has expanded greatly in industrial, chemical, and metallurgical fields, while at the same time modernized methods of mining and refining lithium have increased production. Technical literature includes many papers describing the geology and mineralogy of lithium deposits. Mining and beneficiating problems, however, have not been thoroughly described. Published reports have failed to emphasize that one of the chief reasons lithium minerals were not extensively mined until recently is the difficulty of beneficiation. Four lithium minerals of pegmatites and the lithium-sodium-phosphate byproduct from the brines at Searles Lake, Calif., have been sources of lithium. Among the pegmatite minerals, only spodu-mene and petaline are known to occur in deposits large enough to support large tonnage operations. Spodumene, a lithium-aluminum-silicate, is the principal lithium mineral mined in the U. S. Lithium Corp. of America, during its rapid development and growth, has successfully employed three different methods of concentration: 1) hand sorting, 2) Heavy Media separation, and 3) froth flotation. Each method, though economic in its sphere, is becoming outdated as extractive techniques improve. The most recent development has taken place at Lithium Corp.'s new operation in North Carolina, where the extractive process yields lithium compounds directly from mined rock without an intervening concentrating step. Until 1954 Lithium Corp. mined only in the southern part of the Black Hills of South Dakota, where the various types of lithium-bearing pegmatite could be used to develop untried processes of beneficiation. Concentrates from these operations are shipped to the corporation's chemical plant in St. Louis Park, Minn., where actual extraction of lithium and production of commercial compounds takes place. Nature of Deposits The geology of the southern Black Hills pegmatite deposits is admirably presented by a U. S. Geological Survey publication.' Only the factors pertinent to exploitation need be mentioned here. Lithium Corp. has been interested primarily in three deposits, the Edison, the Mateen, and the Longview-Beecher No. 2. The history of these deposits dates back to the mining boom of 1880 to 1900 in the Black Hills, when most of the deposits were prospected for tin by the ill-fated Harney Peak Tin Mining Co. The three deposits described here, however, lay idle and unwanted until Lithium Corp. opened the Edison mine in 1943 and the Mateen and Longview-Beecher No. 2 in 1951. Edison Deposit: The Edison deposit is about a mile southeast of Keystone, S. D., on the northeastern flank of the Harney Peak uplift. The deposit consists of no less than four and probably at least six separate pegmatites that coalesce in a central mass from which the individual pegmatites finger outward and downward in complexly folded schist and gneiss beds of the country rock.

Jan 1, 1956

By R. T. DeHoff

A new approach to the measurement of the size distribution of particulate structures imbedded in opaque bodies is developed. The method is based upon the assumption of a general two-parameter distribution curve, and the estimation of these two parameters from three well-known counting measurements made upon metallogvaphic sections. The total number of particles in the system is also a product of the analysis. Application of the method with the assumption of the logarithmiconorma1 disfribution function is developed in detail. A complete description of the geometry of a particulate structure requires the determination of the size distribution of particles. The problem of estimating the size distribution of particles of a particular phase in a multiphase system, or the grain-size distribution in a homogeneous system, has been approached by many investigators.'-'0 All of the solutions proposed by these investigators share the following characteristics. a) A minimum of several hundred particle sections in the microstructure must be examined, and some characteristic dimension recorded, such as area,3'5 intercept length,6"9 or diameter.1'2'4'10 b) The resulting data must undergo a series of fairly complex calculations to generate the empirical histogram which describes the size distribution in three dimensions. c) In order to manipulate the result, the histogram must be fitted to some assumed mathematical formula, using the attendant statistical procedures. d) With two notable exceptions,8,10 the particles must be spherical. The measurements and calculations involved are in general very tedious and time-consuming, with the logical result that much effort has been expended in the development of equipment which will perform these tasks automatically and semiautomati-cally.9,11-15 considerable success has been achieved in this area, but the equipment is in general expensive, and usually places stringent requirements On the quality of microstructure which can be reliably analyzed. In laboratories which do not possess such equip- ment, the analysis of geometry is usually limited to measuring total properties of the microstructures, such as volume fraction and interfacial area, because the measurements required are much simpler to make. The determination of size distributions rarely is undertaken. The development which is presented in this paper permits the estimation of size distributions of three-dimensional structures from the same simple counting measurements which are required to determine the surface area and volume fraction of the particulate structure, and one other counting measurement. The basic approach that is used is to assume a general mathematical form for the distribution, which is described by two parameters (as the normal distribution is described by assigning values to the mean and the standard deviation), and then estimate these two parameters from the results of the counting measurements. The introduction of a third counting measurement also permits the evaluation of the number of particles per unit volume, Nv.

Jan 1, 1965

By D. M. Buck

greatly restricted and every effort is being made to do away with it where possible, and to substitute a lead-base babbitt or a babbitt with 50 per cent,. tin. The amount of solder having the composition 50 lead, 50 tin, used by the Pennsylvania Lines East, during 1917, was approximately 100,000 lb., but there is reason to believe that a large portion of this can be replaced by a 60-lead, 40-tin solder with satisfactory results, and instructions have been issued to this effect. Inregard to the quantity of new tin used, it is not possible to give the amount, except approximately and from calculations based on the 1917 consumption of bearing metals by the Pennsylvania Lines East only, it is estimated that about 770,000 Ib. of new tin were required in a total of about 21,380,000 lb. of all kinds of bearing metals turned out by the foundry or purchased in the market. No change has been made in the specifications for bearing metals for some years, as the metals used have been satisfactory. A large proportion of the bearing metals are made up from old material re-melted and brought to standard composition by some addition of new metal, and every effort is being made to utilize old material to the best advantage and reduce the amount of new metal of all kinds purchased. For a number of years no tin has been used in the lining metal of either passenger or freight car journal-bearings, except such small amounts as come in from re-melting old linings. No change has been made in phosphor bronze used for rod bushings, as we should expect some trouble from bushings pounding out of shape if a phosphor bronze were used which contained less tin or more lead than the present specifications call for. In this, as well as in the case of all other bearing metals, we expect to use our utmost endeavors to economize and to substitute for tin wherever possible. The Tin-plate Industry D. M. Buck,* Pittsburg, Pa.—During the first 5 months of 1918, approximately 11,000,000 Ib. per month of pig tin were consumed in the United States. Solder, bearing metals, bronzes, etc, used about 5,500,000 lb.; collapsible tubes a little more than 250,000 lb.; tin-foil about 500,000 lb.; and the tin- and terne-plate industry somewhat less than 5,000,000 Ib. In an effort to reduce this consumption and thus conserve our tin supplies, several methods of procedure suggest themselves: 1. Salvage. The most careful and systematic collection and re-use of tin and tin-bearing materials is economically important, in that we thus

Jan 1, 1919

By G. N. Goldberg, Robert A. Rapp

The steady-state kinetics and microstructures of simultaneous internal oxidation and external scale formation were investigated for the oxidation of Cb-Zr and Ch-Zr-Re alloys in pure oxygen at 1000°C. For each binary alloy, a constant rate of scale formation was observed at steady state; the internal oxidatton zone reached a steady-state, time-independent thickness. The dependence of the scaling rate on zirconium content exhibited a maximum at a low zirconium colttent; more concentrated alloys oxidized at a slower rate than pure columbium. This composition dependence of the scaling rate may be partially attributed to the effect of the internal oxidation process as an intenla1 sink for oxygen, with the formation of voluminous, and relatively impermeable ZrO2 precipitates. However, the morphologies of the ZrO2 internal oxide precipitates also affected the scaling rate. The internal oxide precipitates were distributed uniformly in the external scale. The steady-state thicknesses of the internal oxidation zones were not in agreement with those predicted theoretically from an idealized simple model. However, in this particular alloy systen1 the ideal model is not satisfied experitmentally. For ternary Cb- Zr - Re alloys with Nr10e = 0.02 or 0.05, the steady-state thicknesses of the internal oxidation zones were less than those for the corresponding binary Cb-Zr alloys. For ternary alloys with NRe(0) - 0.05, a more adherent and much less porous external scale was formed, and a reduction in the kinetics of scale formation was observed. A number of authors'-7 have reported linear oxidation kinetics for the reaction of pure columbium at 1000°C in air or in oxygen of about 1 atm pressure. A thin and tightly adherent oxide layer is found at the metal/oxide interface beneath a porous external layer of scale. Although the suboxides CbO and CbO2 represent thermodynamically stable phases at 100O°C, generally only Cb2O5* is identified as a reaction product in quenched specimens. Studies at 1000°C at lower oxygen pressures8,10 (Po2 - 10-4 Torr) show that both CbO and CbO2 do form and that CbO2 is a protective oxide. The growth of CbO2 results in parabolic kinetics until Cb2O5 is nucleated and grows. Apparently because of the large volume change associated with its formation, Cb2O5 is porous and does not serve as a diffusion barrier; linear kinetics prevail after the surface is covered with Cb2o5. On the basis of these observations, several authors5,9,10 have suggested that the linear oxidation of pure columbium at 1000°C in air or oxygen of 1 atm is limited by a Loriers-type mechanism,11 whereby the total rate or reaction is controlled by ionic diffusion through a thin layer of CbO2 which is maintained at a constant thickness throughout the linear oxidation. However, the concept of a Loriers model for a three-phase CbOlCbO2 Cb2O5 scale, with the only oxygen activity gradient across the NbO2 phase, is not self-consistent. Further, the suboxides CbO and CbO2 were not observed in the high-temperature X-ray diffraction study of columbium oxidation by Goldschmidt.8 From investigations in which the large PO2, dependence of the linear scaling rate was demonstrated, the importance of an oxygen adsorption or dissolution step has been suggested.4,5,7,10,12 Thus the mechanism for the linear oxidation of pure columbium remains quite controversial. Since further insight into the oxidation mechanism of pure columbium is not provided by this investigation, the authors wish to emphasize at the outset that their experimental results are not interpreted in terms of a particular rate controlling step for the oxidation of pure columbium. Previous investigations13-18 of the oxidation of Cb-Zr solid-solution alloys in air or oxygen at 1000°C suggest a remarkable dependence upon zirconium content. For an alloy of bulk zirconium mole fraction, N2r(0) equal to 0.05 or 0.10, the oxygen uptake is reported to be as high as four times greater than that for pure columbium;13,14 for alloys with NZr(0) 0.05 or 0.10 the oxygen uptake is reported to decrease with increasing NZr(0); to a minimum uptake of about one quarter that for pure columbium at NZr(0): = 0.50.13-15Since zirconium forms a more stable oxide (ZrO2) than the lowest columbium oxide (CbO), and since columbium exhibits a high solubility19,20 and diffusivity21,23 for oxygen, the internal oxidation of the zirconium component to ZrO2 is expected at a reaction front ahead of the advancing metal/scale interface. The external scale is then formed at the metal/scale interface by the inward migration of oxygen through the scale, probably through a series combination of molecular and ionic diffusion. Internal oxidation in conjunction with external scale formation has been investigated by Maak24 for the oxidation of dilute Cu-Be alloys in pure oxygen at 850°C. For cu-Be and many other binary alloys,24-27 very small, essentially uniaxial internal oxide particles are formed in the most dilute compositions; for somewhat more concentrated alloys. the internal oxide particles precipitate as platelets or needles. From pertinent solutions to the diffusion equation, Maak28

Jan 1, 1967

By J. L. Snoek

[ ] DISCUSSION J. L, SNOEK*-Stress-induced preferential diffusion in cubic body centered metals in the annealed state provides us with a powerful tool for determining the mobility of interstitially solved atoms as well as their location in the lattice and the exact nature of the distortion brought about in the lattice by their presence. Calculations given by D. Polder31 show that the distortion of the lattice, besides being proportional to the applied stress P, is also proportional to [VC, RT + xVCo] where T, V and Co are the temperature, molar volume of the solvent and molar concentration of the solute respectively and x is a constant describing the mutual interaction energy of the dissolved particles. This calculation obviously is no longer valid if x is negative and the abso¬lute value of xVCo surpasses that of RT. The lattice may then be expected to become tetragonal spontaneously. Such a spontaneous tetragonality seems to have been observed by W. Klemm and L, Grimm for the case of oxygen solved in vanadium.32 Measurements of the internal friction in cold worked iron containing carbon or nitrogen should provide us with information on the mobility as well as the preferential location of these particles in the iron lattice in the cold worked state. The work by T'ing-Sui Kê is a valuable contribution to this problem, The data obtained by T'ing Sui Kê and myself on cold worked samples of iron seem to indicate that carbon and nitrogen in these samples are found either in the normal (1/2 , 0, 0) interstices or in a new preferential position created by the cold working. The latter positions in my opinion can hardly by anything else but the edges of the dislocations. The observed larger distances of diffusion might be explained by assuming that the carbon atoms when freed from a certain dislocation by thermal agitation must diffuse over several atom distances before being caught in another dislocation. The theory however needs working out and no doubt will be much more complicated than the one valid for the annealed state. T'ING-SUI KÊ (author's reply)-It is highly encouraging to read the written discussion given by Dr, Snoek who initiated the theory of stress-induced preferential diffusion in cubic body centered metals in the annealed state, Since the presentation of this paper, the author has done more experimental work on this subject which seems to be able to settle several of the points raised by Dr. Snoek. It has been found that such stress-induced preferential diffusion occurs also in the solid solutions of carbon,33 oxygen,34 and nitrogen35 in tantalum which has a body centered cubic structure. Analysis of the shape of the observed internal friction. peaks indicates that the inter-

Jan 1, 1948

By G. M. Wiles

The increasing number of problems of the modem mine manager has led the author to discuss the art of management. He lists the principles concerning selection of personnel, exploitation and development, new equipment, process improvements, new processes, maintenance, operating cost data and public relations. Application of the principles to problems of mine startup, operation and rehabilitation are described. Since D. C. Jackling was famous for his adeptness at organizing and training teams of operating personnel, the subject of mine management is particularly appropriate for a Jackling Lecture. In fact, it is doubly appropriate because in very basic ways Jackling's career changed the nature of the tasks and challenges facing a mine manager. Management of mines, of course, is the art of finding and winning minerals economically from the earth's crust, and it involves the use of all the engineering sciences. But also of prime importance is a skill which is not yet a science - the area of management often referred to as human engineering. Since expenditures on staff and labor may well involve more than 50% of the direct costs of operating a mine, ability at human engineering is just as important as the ability to plan and put into effect the most efficient operating procedures. In addition to his ability to select and train operating personnel, Jackling possessed, to a degree unmatched by many of his contemporaries, broad, analytical powers covering both the economics and operating phases of large scale mineral extraction. His breadth of vision found its greatest expression at the time he analyzed the Utah copper deposit. Fortunately, Messrs. Penrose and Gemmell had enough faith in his analyses to furnish the capital needed to begin operations. The result, as is well known to all of you, was Kennecott's lucrative Utah copper mine — and the beginning of the open pit porphyry copper era. The Utah copper mine, and Jackling's subsequent similar successes in Arizona, New Mexico and Nevada, had one thing in common —all of these large porphyry deposits were worthless until open pit, large daily tonnage schemes were developed for their exploitation. The successful development of such schemes made vast new mineral resources available for economic exploitation. But at the same time, the trend away from smaller high grade operations in favor of the far more complicated operations required to handle large deposits of low grade ore have greatly altered a mine manager's problems. We are all familiar with the saying "mines make managers." There is still some truth in this statement, but far less than there used to be in the days when high grade properties were the rule rather than the exception. When high grade orebodies prevailed, many managers, superficially at least, could not make a mistake because the profits of their mines

Jan 1, 1962

By H. E. Hostetter

GROSSMANN'S method1 for calculating the hardenability of steel from the composition and grain size has gained wide acceptance, and when properly used, has been well proved in practical application, both for estimating the hardenability of known compositions and for selecting compositions to meet known hardenability requirements. The Grossmann method uses as the criterion of hardenability the "ideal critical diameter," DI, which is the size round that will just harden to a structure of 50 per cent martensite at the center when given the theoretically fastest quench, or "ideal quench." The DI can be related to actual quenching practice if the severity of quench is known; or the DI can be correlated with hardenability as determined by the Jominy end-quench method.2 The effect on hardenability of each element present in a steel can be represented by a multiplying factor, the value of which depends on the amount of the element present and the degree of effectiveness of the particular element. (The value of the factor for a given carbon content varies with the grain size.) When the factors for all elements present in a steel have been determined from charts, they are multiplied, and the resultant product is the D, of the steel. The validity of Grossmann's scheme of multiplying factors has been confirmed in a number of other investigations.3 -6 It can be appreciated that a certain desired level of hardenability can be obtained by adding chromium, molybdenum, nickel and vanadium to a base composition containing carbon, manganese, silicon and the usual impurities. Many of the ranges of hardenability used commercially can be obtained by any of the foregoing alloying elements used singly in the base composition. The same hardenability levels also can be obtained through use of any of a great number of multiple element combinations of these alloying elements. In this report a method will be presented for determining what one combination is the most efficient (based on hardenability and cost of added alloy) for a given level of hardenability. It should not be assumed from the emphasis given to hardenability, that hardenability is the only criterion for the selection of an alloy composition. Such properties as the hot-working characteristics, machinability, carburizing characteristics, amount of distortion during quenching and the retention of austenite may be considerations of importance in many applications. However, hardenability is one of the most important properties of an alloy steel and one that must be considered in almost all cases involving heat-treatment by quenching. Therefore, a method for determining the lowest-cost alloy combination should be of considerable value. DETERMINATION OF MOST EFFICIENT COMBINATIONS For comparing the alloying elements on standards of cost and hardenability, it

Jan 1, 1945

By Malcolm McColl, C. A. Mead

Thin films (of mica have unique attributes that are exceptionally good for studies of high-field conduction mechamisms in thin-film insulators and the quantum mechanical tunneling of electrons from metal to metal. The principal advantages of using mica films are that the films are crystalline and the cleavage planes occur every 10Å. This property results in films whose thicknesses are integral multiples of 10Å and whose surfaces are uniformly parallel over sizable areas. Hence, very well-defined metal -mica-metal structures are possible. Furthermore, the fact that the insulator is split fro??! a bulk sample allows the index of refraction, dielectric constant, forbidden energy gap, and trapping levels and their density- to be obtained directly from measurements performed on thick samples Of mica rather than requiring that these properties be interred from the conduction characterrsties alone. In the work to he described, all the cleaving was done in a high vacuum just prior to the evaporation of metal elertrodes so as to avoid air contamination at the interfaces. Results of these studies indicate that the current through the 30 and 40Å films exhibited quantitative agreement with the theoretical voltage and temperature dependence derived by Strallon for the tunneling of electrons directly from metal to metal. Thicker films at room temperature exhibited volt-ampere curves suggesting Schottky emission of electrons from the cathode into the conduction band of mica. However, the thermal activation energy was smaller than that found from other measurements, and the experimsntal Schottky dielectric constant was larger than the square of the index of refraction. These facts would indicate that the electrons were being injected into polaron stales ill the iusulator. At low temperatures and high fields, the current through the thicker films did not exhibit the Fowler -Nordheim dependence as would be predicted by a simple extention of the theory of field emission into a vacuum. THE mechanism of electrons tunneling through insulating films has received considerable attention in the last few years due to the devices possible utilizing tunneling'-4 and the success of tunneling in the study of superconductivity.5,6 Until the recent paper by Hartman and chivian7 on the study of aluminum oxide, there had been no reported successful quantitative experimental fit to the theory. Their method of fabrication necessarily results in a polycrystalline insulator, the stoichiometry of which is nonuniform from one side to the other. This structure also introduces complications to the shape of the barrier which is set up by the insulator since the insulator possesses a spatially nonuniform band structure and dielectric constant. Due to these facts an analysis of the data in terms of a pviori barrier shape is of questionable validity. The use of muscovite mica not only overcomes these disadvantages but, as an insulating thin film, provides physical properties (dielectric constant. trapping levels and their densities, forbidden energy gap, and so forth) that are identical to the easily measured values of the bulk sample. Furthermore, it is a single-crystal insulator whose cleavage planes (10Å apart8,9) provide uniformly parallel surfaces of well-known separation. This material is therefore ideally suited to the study of electron-transport phenomena. Von Hippel10 using a 6.5-µ-thick sample was the first to observe the high-field conductivity (=5 x l06 v per cm) of mica. No attempt was made to develop an empirical formula, but Von Hippel concluded from intuitive arguments that the current was being space-charge limited by trapped electrons. Mal'tsev11 in a more recent investigation at high fields observed a dependence of the conductivity a on the field F of the form exp(ßF1/2). This dependence was attributed to the Frenkel effect,12,13 a Schottky type of emission from filled traps. No mention in the English abstract was made of the thicknesses of his samples or, and more important, of how well the value of ß fit Frenkel's theory. In 1962 Foote and Kazan14 developed a technique for splitting mica to a thickness of less than 100Å and observed a dependence of the current density j on the field of the form j = jo exp(ßF1/2) on a thin sample thought to be 40Å thick. Assuming that this was a Schottky emission process and that the appropriate dielectric constant for such a mechanism would be closer to a low-frequency value of 7.6, Foote and Kazan calculated from ß an independent thickness of the mica of 36Å. No further investigation was made of the phenomenon. However, the work reported in this paper indicates that the film measured by Foote and Kazan was probably 60Å thick, the error arising from the measurement of the very small metal-insulator-metal diode areas that were used, along with the diode capacitance and dielectric constant, to calculate the thickness. In the research reported in this paper, Foote and Kazan's technique was modified to cleave muscovite in a vacuum of 10-6 Torr, immediately after which metal electrodes were evaporated creating Au-mica-A1 diodes. Aluminum was chosen because of its strong adhesion to mica, as necessitated by the

Jan 1, 1965

By R. E. Cech, J. H. Hollomon

KURDJUMOV and Maksimova reported experiments with manganese steels and high carbon steels' and with an Fe-Ni-Mn alloy' in which mar-tensite was formed isothermally over a range of temperatures. They found in some cases that mar-tensite formation could be suppressed by rapid quenching to liquid nitrogen temperature. From their microstructural observations of martensite formed isothermally, they concluded that the rate controlling step is nucleation rather than growth. Kulin and Cohen,3 in an attempt to reproduce these experiments, found that with a steel having the same composition as that reported by Kurd-jumov and Maksimova, the transformation to martensite was essentially complete above the temperature range of Kurdjumov and Maksimova's isotherms. The possible reasons for this disagreement were not considered. Recent papers by Das Gupta and Lement4 and Kulin and Speich5 report the formation of isothermal martensite in a high chromium steel and in an Fe-Cr-Ni alloy, but neither paper can be considered a verification of the original Kurdjumov and Maksimova results. Further, in neither case were the authors able to suppress the formation of martensite entirely. Because of the important bearing the Kurdjumov and Maksimova results have to an understanding of the mechanism of martensite reactions it was felt that an experimental investigation directly concerned with checking the validity of their results was in order. This paper describes the results obtained on the isothermal transformation over the temperature range from —79" to —196°C of an alloy of iron, nickel, and manganese. Experimental Apparatus A 15 lb heat of an alloy containing 73.3 pct Fe, 23.0 pct Ni, and 3.7 pct Mn was melted by induction and cast under argon. The ingot was forged to 1-in. bar and a portion rolled to 1/16x1 1/2-in. strip. This strip was pack-homogenized 300 hr at 1100" in a helium-filled sealed iron tube. The composition after homogenization was 73.2 pct Fe, 22.94 pct Ni, 3.73 pct Mn, 0.05 pct C, and 0.015 pct N. The strips were cut to 1/2-in. width for dilatometer and metal-lographic specimens. Only the center portion of the 11/2-in. strip was used in the present investigation. The dilatometer employed was similar in design to one described by Flinn, Cook, and Fellows." A concentric fused auartz rod and tube assembly with hooks for holding the specimen was mounted so as to transmit the specimen dilation to a 1/10,000 in., 1/10 in. travel dial gage. The dilatometer proper was mounted by means of extension arms to a counterweighted sliding member on a vertical standard. This method of mounting permitted rapid transfer of the dilatometer from the austenitizing furnace to the quenching bath and low temperature chamber. A small electrical vibrator on the dilatometer kept frictional effects of the quartz members at a minimum. The austenitizing unit was a vertical, molybdenum-wound, hydrogen atmosphere furnace maintained at a constant temperature ±3°C by means of constant power input. A 12-in. stainless steel jacketed copper liner having 1/2-in wall thickness acted to equalize the temperature in the hot zone of the furnace. This liner, closed at the bottom end and open at the top to permit entrance of the dilatometer and specimen, was kept filled with dry nitrogen gas. A chromel-alumel thermocouple was placed inside the tube to determine the temperature. The 4-in. dilatometer specimens in the chamber varied less than 1/2° across the specimen length except for a 1 1/20 drop at the end nearest the open end of the furnace. The low temperature isothermal holding bath was a double Dewar arrangement similar to one described by Turnbull7. The outer bath was filled with a refrigerant at a temperature lower than the desired holding temperature. The inner bath was filled with Freon "11" or "12" or a mixture of both, depending upon the holding temperature. This inner bath which tended to be cooled by the outer bath was kept at a constant temperature by introducing a small amount of heat with a manually controlled electric heater. Stirring was accomplished by bubbling dry air through the bath. A Leeds and North-rup type K potentiometer was used to measure the inner bath temperature as indicated by a five element copper-constantan thermopile. The bath temperature was maintained within ±0.2°C of the desired temperature by occasionally adjusting the heater current so as to keep the Leeds and Northrup galvanometer at zero deflection with a constant setting of the potentiometer. Isothermal tests were usually continued for 300 to 400 min and another reading made at approximately 1000 min if the bath, unattended overnight, had not deviated in temperature more than 5°C. Transformation curves are drawn dashed (Fig. 1) through the time region where temperature was not controlled precisely. Experimental Procedure Dilatometer specimens of 1/2x1/16-in. strip were cut to 41/2-in. length and holes were drilled for the quartz hooks with proper spacing to give a 4-in. measured length. A thermocouple consisting of 0.012-in. diameter chrome1 and alumel wires was spot welded to the specimen and threaded between the dilatometer rods to binding posts near the dial

Jan 1, 1954

By R. W. Heckel, R. E. Trabocco

The recovery process in 400 Monel filings was followed, principally, by using the Warren-Averbach technique of X-ray peak profile analysis. The deformation fault probability, a, was 0.006 in samples of unannealed filings. a , the twin fault Probability , was approximately 0.002 in samples of unannealed filings. Both a and 0 were found to "anneal out" at 600°F. The effective particle size and mzs strain increased and decreased in the (111) direction, respectively, with increasing annealing temperature. The actual particle size was found to be almost equivalent to the effective particle size. Tile small values of deformation and twin fault probabilities accounted for the similarity in values of the effective and actual particle sizes. Stored strain energy and dislocation density calculations based on rms strain decreased with increasing annealing temperature. The dislocation density decreased from 10" per sq cm in the unannealed filings to 10' per sq cm in the partially re-crystallized filings. The square root of the dislocation density based on strain to that based on particle size indicated a random dislocation distribution in the unannealed filings. The dislocation arrangement changed to one with dislocations in cell walls with increasing annealing temperature. THE recovery processes which occur in metals are generally thought to be a redistribution and/or annihilation of defects.' Investigators' have shown that recovery processes can be characterized by X-ray line-broadening analyses. Michell and Haig4 measured the stored energy of nickel powder by calori-metry and found the value to be greater by a factor of 2.5 than that from X-ray data obtained by the Warren-Averbach technique.= Minor increases in particle size occurred up to 752°F (recovery), while above 752°F the particle size increased greatly due to recrystalliza-tion. X-ray microstrain values decreased between room temperature and 392"F, remained constant from 392" to 752"F, and decreased from 752°F to a negligible value at 1112°F. Faulkner developed an equation for calculating stored strain energy based on X-ray line-broadening data which gave a closer correlation of measured and calculated stored strain energy based on the data of Michell and Haig. The stored strain energy released during recovery is predominately dependent on the decrease in dislocation density which was p-enerated from cold work.7 Stored energy has been measured8 in alkali halides during recovery and recrystallization and 80 pct of the stored energy was found to be released during recovery. Dislocation distributions have been studiedg in a number of fcc metals by thin-film electron microscopy. Howie and Swann" found the stacking fault energy of copper and nickel to be 40 and 150 ergs per sq cm, respectively. ~rown" has pointed out that these stacking fault energy values should be corrected to 92 and 345 ergs per sq cm, respectively. The dislocation distribution of a metal is directly dependent on the stacking fault energy of the system. Metals of high stacking fault energy such as aluminum cross-slip readily and do not form planar arrays of dislocations. Metals of lower stacking fault energy such as stainless steels" do not cross-slip readily. Cold-worked nickel has been found to form a cellular dislocation structure after annealing.13 The relatively high stacking fault energy of nickel and copperlo to a lesser extent favor cellular structures of dislocations rather than planar arrays after deformation. The present study of recovery was carried out on a Ni-Cu alloy (Monel 400) to compare with prior studies for pure nickel and pure copper. X-ray line-broadening techniques were used to measure the effect of recovery temperature on rms strain and particle size and the results were compared with previous studies on copper'4-'7 and nickel., Calculations were also made on stacking fault probabilities, dislocation density, dislocation distribution, and stored strain energy as affected by temperature. EXPERIMENTAL PROCEDURE The nominal analysis of the Monel 400 used in this investigation was: 66.0 pct Ni, 31.5 pct Cu, 0.12 pct C, 0.90 pct Mn, 1.35 pct Fe, 0.005 pct S, 0.15 pct Si. The annealed material was cold-reduced in two batches, one 50 pct and the other 80 pct. It was originally planned to conduct line-broadening studies of these bulk samples; however, rolling textures that developed produced low-intensity peaks which were not suitable for line-broadening analysis. Filings were prepared at room temperature from both the 50 and 80 pct cold-reduced specimens, series A and series B, respectively, and were not screened prior to heat treatment or X-ray studies. Heating to the annealing temperature, 200" to 120O°F, was accomplished in a matter of minutes in a hydrogen atmosphere. Following heat treatment, some of the filings were mounted and polished for microhardness measurements with a Bergsman microhardness tester, using a 10-g load. A G.E. XRD-5 diffractometer using nickel-filtered Cum radiation was used to obtain all diffraction patterns. Only (111)- (222) line-broadenin data were used in the present study since the {400f peaks were too weak to use. The Fourier analysis of the (111) and (222) peak

Jan 1, 1969