Search Documents

By R. H. Lynn, T. C. Craig

During the year 1933, in the Texas Panhandle, 113 oil wells were completed, adding 33,337 bbl. to the daily potential of the field. The field potential on Jan. 1, 1933, as determined by the Texas Railroad Commission, was 149,260 bbl., with a daily allowable production of 41,000 bbl. The potential was raised gradually, until on July 16, 1933, it reached 155,344 bbl. with a daily allowable of 55,000 bbl. This potential and allowable was maintained over a period from July 16, 1933, to Sept. 8, 1933, when the potential was reduced to 136,893, with a daily allowable of 43,727 bbl. Since Sept. 8, 1933, there has been a gradual increase, until on Jan. 1, 1934, the field potential reached 159,740 bbl. with a daily allowable of 42,000 bbl. Of this amount 26,429 bbl. arc "marginal oil" and 2682 bbl. are exempt on account of water. Deepening of Wells During the year 64 wells were deepened, increasing their total oil production 9631 bbl. per day. Of this amount the Gray County granite wash contributed 9256 bbl. from 57 wells. It has been found in many places that the granite wash carries an additional oil pay from 50 to 75 ft. below sea level. The majority of the wells that were .drilled during the early development in Gray County encountered their oil above sea level. When the wells producing from the upper horizon have become unprofit-

Jan 1, 1934

By C. E. Shoenfelt

Operations ill Colorado oil fields in 1934 were not quite so extensive as in 1933, but much better results were obtained and one new oil field was discovered. In all, 26 wells were drilled, of which 9 were oil wells, 1 was a gas well, and 16 were dry holes. New oil production totaled 10,220 bbl. and new gas production totaled 33,714,000 cu. ft. This compares with new oil production in 1933 of 1238 bbl. and new gas production of 14,307,000 cu. ft. Dry holes in 1933 totaled 29 as conlpared with 16 in 1934. Oil was discovered in the Hiawatha gas field, Moffat County, in 1934 in the Mountain Fuel Supply Company's No. 4B Wilson, C. NE. NW. of sec. 23, 12N., 100W. This well was completed in a sand in the Wasatch (Tertiary) at 2304 to 2337 ft., after plugging back from 3797 ft. It made 20 bbl. of oil initially. No. 4B Wilson is the first well in the Rocky Mountain region to discover oil in commercial amounts in rocks younger than Cretaceous, and while it is not expected that Hiawatha will develop into an oil field of important proportions, eventually it may produce a considerable amount of oil as the gas pressure declines. The Hiawatha gas field was discovered in 1926, on one of six structures in what is known as the Vermillion Creek gas area. It is a northeast-

Jan 1, 1935

[Secretary's Note.—The following official tables, prepared by the government of the State of Nuevo Leon, and presented to the Institute at the fifth seseion of its Mexican meeting, held at Monterrey, November 26, 1901, present in compact form a general summary of the mineral and metallurgical industry of the State for the preceding calendar year, together with a statement of the railway-shipments of ores from January 1 to October 31, 1901, which, in the absence of direct official mining and metallurgical statistics (not yet available for that year), clearly indicates an increased activity and productiveness of these industries. In other words, the mines are reported to have yielded in 1900 a total product of 83,960,169 kilos of ore; whereas, the railway is reported to have carried, in 10 months of 1901, a total of 108,318,647 kilos of ore. At this rate, the railway-shipments for 1901 mould amount to nearly 130,000,000 kilos. It is, of course, possible that the railwaystatistics include other freight than ores, or that they include duplications, such as would be involved in the record, first of certain ores transported, and afterwards of the " base bullion " produced therefrom. An accurate comparison is therefore impossible ; yet, after making all reasonable allowances for such items as have been named, it seems safe to infer that the mining and metallurgical industry of this State accomplished in 1901 a substantial progress.]

Jan 1, 1902

By Peter Allen, John R. Stuermer

COUNTRY RISK ANALYSIS A company operating in a foreign country assumes all the risks that it would at home. However, beyond these, it assumes risks that arise from the unique political economic, financial conditions of the foreign country which it operates. These risks are known as "country risks". The importance of these risks has grown appreciably in the recent past (particularly in the aftermath of Iran's revolution in the late 1970s and Mexico's debt rescheduling of 1982-83), and as a result, country risk analysis has become an increasingly useful management tool. Country risk analysis seeks to assess the probability that countries will service their aggregate foreign liabilities on time, as well as the probability that country conditions could inhibit the debt service capability of private sector debtors. This involves assessment of both the ability and the willingness of countries to meet their external liabilities in a timely fashion. "Ability" is linked economic and financial variables: principally, a country's economic structure, foreign exchange generating capacity and debt service burden. On the other hand, "willingness" is tied to political factors: mainly the economic/financial orientation of government policy and the stability of economic decision making. Ability: Economic, Financial Conditions and Prospects Judgement of a country's ability to meet foreign financial obligations begins with a detailed study of a country's external balance sheet which compares the country's foreign liabilities and assets. Table 1 below presents country balance sheets for Mexico, Korea and Indonesia. [TABLE 1 The External Balance 3-,-et 1983 (billions of dollars; Indonesia Mexico Korea Foreign Liabilities 31.1 67.6 40.5 By Source: Bank 13.1 75.5 26.3 Non-bank 18.0 12.114.2 Foreign Reserves 9.3 4.7 7.0] The large magnitude of Mexico's external debt (nearly $90 billion), compared to foreign assets of approximately $5 billion, illustrates the weakness of this country's external payments position, and the main reason that it has been unable to meet interest and principal payments and been forced to reschedule its foreign debt. On the other hand, the relationship between Korea's external liabilities and assets ($50.5 billion and $7 billion, respectively), is more favorable and helps explain why Korea has been able to meet debt service payments and maintain its access to the international capital markets. Indonesia has even a more favorable relationship between its foreign assets and liabilities, $31 billion and $9 billion, respectively, and its debt is mostly lower interest rate, non-bank debt, making for a less onerous debt service burden. After the balance sheet, the analysis turns to a comparison of the country's foreign exchange earning capacity and its prospective financing requirements, that is, the country's future earnings stream

Jan 1, 1985

By J. C. Bradley

THE relation of annealing temperature to conductivity of copper wire has been determined.1 Conductivity hard was 98.26 per cent. After a 10-min. heating at 200° C. it was 98.69. By annealing 10 min. at 300° C. a large increase, to 100.93, occurred. Maximum conductivity, 101.15, was attained after a 500° C. anneal; thereafter it decreased to 100.53 after a 950° C. anneal. If copper is gassed the decrease is much more than this. MATERIAL AND METHOD The work was done on high grade electrolytic copper, 99.942 per cent. copper-plus silver, silver 0.0008 per cent. It was hot-rolled to 3 in., then cold drawn to 0.080 in. The wire was cut into 25 5-ft. lengths and numbered 1 to 25 as cut. Four samples were tested hard. The others were wound into 5-in. diameter coils. For the 100° C. heating a coil was put into water, the water brought to boiling, and the wire kept at this temperature for 10 min. For the higher temperatures the coils were placed in envelopes of sheet copper, a little water added, and the envelopes sealed by folding over the edges twice, and hammering them together. This kept the air out very well. The envelope and wire were brought to the desired temperature; this was maintained for 10 min., then the whole was water-quenched.

Jan 1, 1927

By R. A. Deju, R. B. Bhappu

The basic structural unit of all silicate minerals is a tetrahedron with a silicon atom at the center and four oxygen atoms at the corners. The oxygen-silicon distance is about 1.6 & and the oxygen-oxygen distance about 2.6 &. The different types of oxygen-silicon frameworks in the various silicates are based entirely on the combinations of the tetra-hedral oxygen-silicon groups through sharing of oxygen atoms. In recent years, infrared spectroscopy has permitted estimation of the ratio of the ionic character of the oxygen-silicon bond to be a few times that of the oxygen-carbon bond and the ratio of electro-negativity of the two bonds has also substantiated this finding. On this basis, it is generally accepted that the oxygen-silicon bond is the strongest one occurring in silicate minerals. As the oxygen-silicon ratio increases from quartz to the olivines, a greater percentage of the oxygen bonding power is available for bonding to cations other than silicon. Hence, with an increasing oxygen-silicon ratio, there is increasing oxygen-to-metal bonding. Upon the fracturing of a silicate mineral crystal, the oxygen-metal bond, which is almost entirely ionic in character, should break more easily than the stronger oxygen-silicon bond, resulting in a greater number of unsatisfied negative forces on the surface. If, then the mineral is immersed in a liquid containing hydrogen ions, these negative forces should tend to be neutralized by hydrogen ions from solution, resulting in a change of the pH of the solution. An increase in the degree of adsorption of hydrogen ions is to be expected as the oxygen-silicon ratio in the crystal structure increases. This study attempted to correlate the oxygen-silicon ratio for various representative silicate minerals to the adsorption of hydrogen ions. Experiments to determine the effect of surface area on this adsorption and to investigate the effect of surface iron were also conducted. It is believed that such studies of the surface properties of silicate minerals will supply pertinent information about their behavior in froth flotation systems. EXPERIMENTAL PROCEDURE Ion Exchange: Carefully selected, hand-picked samples of the minerals investigated were dry-crushed in a ceramic ball mill and sieved to obtain a minus 100 plus 200-mesh sample. The sized samples were then run through the electro-magnetic separator to remove any iron-bearing particles. A 10-g sample of each mineral was placed in 100 ml of freshly deionized water previously adjusted to a pH of 3.50 with HCl. The beaker containing the sample and the water was placed under a bell jar from which the air was displaced at once by nitrogen gas from a tank. All experiments were carried out in a nitrogen atmosphere. The sample and solution were stirred gently but continuously during the entire experiment, the stirring speed being kept about the same for all runs. Changes in pH were followed with a Beckman Zeromatic pH meter and recorded on a

Jan 1, 1967

In order to assist in the building up of the industries and commerce of France, by cooperating with the Congres General du Genie Civil, the four Founder Societies have appointed the following committee: E. G. Spilsbury and Arthur S. Dwight representing the American In-stitute of Mining and. Metallurgical Engineers; George F. Swain and Nelson P. Lewis to represent the American Society of Civil Engineers; Charles T. Main and George W. Fuller to represent the American Society of Mechanical Engineers; Lewis B. Stillwell and Andrew M. Hunt to represent the American. Institute of Electrical Engineers.

Jan 12, 1919

By H. H. Power

THE PETROLEUM DIVISION of the A.I.M.E. continued with its diversified activities during 1.935. Sessions at the New York meeting in February were devoted to production engineering, domestic and foreign oil production, and petroleum economics. The symposiums on domestic and foreign production proved their increased usefulness. The data accumulated for 1935 were added to those published during prior years in "Petroleum Development and Technology." A joint session on the use of metals in the petroleum industry was held by the Institute of Metals, Iron and Steel, and Petroleum Divisions. W. S. Farish, chairman of the board of the Standard Oil Co. (N. J.), was the principal speaker at the annual dinner. The October meeting, held in Hous¬ton, was characterized by an excellent program and large attendance. Four sessions were devoted to problems in estimating reserves, reservoir energy, properties of drilling muds, electrical logging, water flooding, and other subsurface studies. Foreign representatives of the Anglo-Persian Oil Co. presented a paper on surface tension and specific gravity of crude oil under reservoir conditions. The address by President Buehler, the dinner at San Jacinto Inn, a trip to various lo

Jan 1, 1936

By G. F. Olsen

ON superficial consideration a technical library might be considered a luxury to the business institution that possesses one. After all, public libraries and research institutions probably contain all the data that would be found in a private technical library, and able consultants are available both within and without a company. In all probability the technical men of a company have in their combined personal libraries sufficient information to answer most inquiries. Nevertheless, possession of such a department is of real economic benefit because of the time it saves its users, because it prevents expensive duplication of technical literature in a company, and lastly, but most important, be- cause it makes readily available a central storehouse of technical facts classified and indexed to meet the demands of the industry or industries concerned.

Jan 1, 1940

By C. W. Davis

THE name fuller's earth, which was derived from its early use in "fulling" or removing grease from woolen goods, is a term that is generally considered to designate mineral matter, containing hydrous aluminum silicates of the clay group, which has a high capacity for removing colors from oils, whether of animal, vegetable, or mineral origin. Fuller's earths are usually dried and may be "tempered" by heating or may be treated with water or reagents to improve their efficiency. For our purpose the term "acid-treated earths" will include those products from the partial decomposition of mineral water -by acid which are equal to or more efficient than an untreated fuller's earth from Quincy, Fla., when used in bleaching mineral oil by the "contact" process. In general, the contact process for treating oils consists of heating and agitating a mixture of oil and finely divided adsorbent, the latter being subsequently removed by filtration. The term "adsorbent" is used because, although there has been a great deal of controversy over the mechanism of removal of impurities from oils by mineral matter, there is no doubt that adsorption, which involves the surface of the solid, plays a major part.1 The properties that make fuller's earth useful in the treatment of petroleum products by "percolation" and in the purification of edible oils by the contact process have long been studied, but the comparatively recent adaptation of the contact process to the bleaching of petroleum products has made desirable the further investigation of fuller's earth and other, adsorbent earths.

Jan 1, 1929

By Richard J. Robbins

Mechanical moles have developed through a tedious process of evolution. At times it has seemed that tunnel borers have been subject to the same Darwinian rules of evolution as their zoological namesakes who, despite their efficiency, are highly specialized and still restricted to soft soil conditions near the surface of the ground. HISTORICAL HIGHLIGHTS The Robbins Co. began its work in this field in 1947 with the development of a twin-bore continuous coal miner. Although these machines were used primarily in coal, two of the early prototypes were used to bore tunnels through shale. Disk cutters were first used on these machines and showed promising results as core breakers between drag-bit kerfs. In 1953, James S. Robbins and Assocs. undertook the development of a 25-ft 9-in.-diam circular tunnel borer for Mittry Construction Co. to be used at Oahe Dam in South Dakota (Fig. 1). This is believed to be the first rock tunnel-boring machine built since the end of the 19th century when short sections of the Channel tunnel were successfully bored in chalk from both the English and French shores. Another Oahe Dam machine was built in 1955, and then a series of three small-diameter machines for the company's first real experience with medium-hard and hard rock (Fig. 2) None of these three could be considered a success, although they laid the groundwork for the success that followed. Interbedded shale and limestone in Pittsburgh and hard limestone in Chicago quickly pointed up the weaknesses in these machines which were used by Perini, Dravo, and Healey. Among the problems were the high breakage rate of tungsten-carbide drag bits, too much flexibility in the drive shafts, failure of high-pressure hydraulic systems, chain-conveyor failure, and general lack of rigidity and strength. In 1956 another attempt at medium-hard and hard rock-boring proved this time to be a success and a significant turning point in the development

Jan 1, 1970

By James B. Cathcart

The potash mine of the International Minerals and Chemical Corp. is about 18 miles east of Carlsbad, New Mexico, in sec 1 and 12, T 22 S, R 29 E, N.M.P.M. Potash is produced from two zones in the Salado formation of late Permian age. The lower zone, consisting of a mixture of sylvite (KCI) and halite (NaCl), lies at a depth of about 900 ft, and the upper zone, in which the principal potassium mineral is langbeinite (K2SO4 2MgSO4), lies at a depth of about 800 ft. Because of the plastic nature of the material, fractures in the Salado formation are extremely rare and have been noted only on the 800 ft level of the International mine. The open fracture described below is almost unique. Only one other open fracture has been noted, and it was on a working face in the same general area as the one described, but was destroyed before the writer had a chance to examine it. According to J. E. Tong, foreman on the 800 level, this fracture was similar to, but smaller than, the one herein described. The saline strata are nearly flat-lying and comprise interbedded layers of halite, anhydrite (CaSO4), and poly-halite (2CaSO4.MgS04.K2SO4-2H2O), with halite predominating. The halite layers contain local concentrations of sylvite, carnallite (KC1.MgCl2.6H2O), and langbeinite. The principal marker in the potash mines area is a bed of anhydrite about 8 ft thick, and 70 ft below the 800 level. This bed contains varying amounts of polyhalite, and locally a few blebs of sylvite. Two principal marker beds are present over most of the 800 level. The lower is the "Middle Salt Marker," a bed of bright-orange halite, which ranges in thickness from a knife-edge to about 0.6 ft, and is usually bounded above and below by thin seams of green or reddish-brown clay. In langbeinite-rich areas, this marker usually contains abundant blebs of langbeinite. The upper of the two principal markers is a green clay seam, containing abundant halite, which ranges in thickness from 0.1 to about 0.5 ft. It is 2 to slightly more than 5 ft above the Middle Salt Marker. No langbeinite of minable grade is found above this clay, and it

Jan 1, 1950

By Stephen G. Wright

Jan 1, 1985

By L. Weaver

THE Tennessee Copper Co.'s mines are in the southeast corner of the state of Tennessee, Polk Co., in the well-known Ducktown copper basin. Their new circular production shaft will eventually be the only ore hoisting shaft, and is located for handling ore from Boyd, Calloway, Mary, and Cherokee mines. A circular, rather than a rectangular, shaft was decided upon because: 1-The circular shaft section is stronger when lined with concrete. Reinforcing steel was not required, thus reducing lining cost by one- quarter. 2-Water sealing was desired; it was thought it could best be done with a concrete lining followed by pressure grouting to eliminate water seeps. 3-The shaft labor saving equipment could best be used in a large opening, so the round section was made for economy, sinking, mucking, concreting and water sealing. Less shaft steel is used than could have been possible with steel sets. There are no posts required; center beams and Tee plate assembly placed at 10 ft hold the 100 lb steel guide rails.

Jan 1, 1950

By N. Parlee, V. C. Kashyap

The solubilities of nitrogen in liquid iron and liquid Fe-Ni, Fe-Mo, Fe-V, and Fe-Mo-V alloys were measured by the Sieverts method. Measurements were made at 1600° to 1800°C on binary alloys up to 20 pet Ni, 10 pet V, 10 pet Mo; and on ternary alloys containing 0 to 3 pet V with 0 to 5 pet Mo. The results on liquid iron confirm that Sieverts' law is obeyed in the range 50 to 750 mm pressure. The measured solubilities and their temperature coefficients are in general agreement with other modern authors. The logarithms of the activity coefficients of nitrogen in the binaries are approximately linear functions of the pet of alloying element. A method suggested by Wagner, Chipman, and others for predicting gas solubilities in complex alloys from solubility data on binaries was applied to the Fe-Mo-V alloys. Reasonably good agreement was obtained between calculated and experimental solubilities. NITROGEN'S solubility in liquid iron has been studied by a number of investigators. It is reasonably well established that the solubility of nitrogen follows Sieverts' law at least up to 1 atm partial pressure and that the solubility increases gradually with temperature. The solubility of nitrogen in Fe-X binary liquid systems has been investigated in only a few cases. Only the systems Fe-Cr,3-5, 7 Fe-V,3 Fe-Mn,3, 5 Fe-Ni,3, 5 Fe-Si,B, H Fe-C, L, H and Fe-P4 appear to have received any study. The only work on liquid Fe-V was done by Brick and Creevy.3 This was limited to 13.5 pet and 26.5 pet V, but no exact temperatures were recorded. No work whatsoever appears to have been done on liquid Fe-Mo alloys and even work on Fe-Ni alloys is rather scant. The work on liquid ternary systems is still more limited, and the only publication available appears to be that of Wentrup and Reif,7 who studied the Fe-Cr-Mn and Fe-Cr-Ni alloys. Rassbach, Saunders, and Harbrecht17 have reported work on the solubility of nitrogen in stainless steel but this was not a systematic study of any particular system. Commercial alloys usually contain several alloying elements. Thus, it often becomes important to be able to predict the nitrogen solubility in systems containing two or more added elements without the necessity of making measurements. Wagner,14 Chipman," Darken and Gurry," and Morris and Buehl 14 have suggested means by which this may be accomplished, and Langenberg14 has recently applied one of these methods to nitrogen solubility in complex liquid alloys. This paper reports the results of nitrogen solubility determinations on Fe-Ni, Fe-Mo, Fe-V, and Fe-Mo-V alloys and compares calculated and experimental solubilities in the ternary alloy. Attempted measurements on Fe-Cr alloys were not successful by the experimental method employed. Experimental Method The general method of solubility measurement was that of Sieverts.' The apparatus and procedure were essentially the same as used by Liang, Bever, and Floe."' The equipment consisted of a small vacuum furnace heated by a 6 kw induction unit, gas measuring apparatus, and a gas purification train. The crucibles used were Norton Alundum with alumina sand around them for insulation. The crucibles were charged with 100 to 200 g of material, about 180 g or nearly filling the crucible being found most satisfactory. Hot volumes were determined with argon and ranged from 95 to 130 cu cm (stp). Temperature measurements were made with a Leeds and Northrup optical pyrometer which was calibrated periodically against the melting point of iron in the same apparatus."-'* Good quality nitrogen, hydrogen, and argon gases were further purified and dried in standard purification trains. The sources of the high purity iron and other alloying elements used were as follows:

Jan 1, 1959

By H. W. Gillett

MAINTENANCE of membership by the technical so¬cieties and the activity of these societies in spite of the adverse business situation have been noteworthy. This forcibly brings home the fact that industry recognizes that sound technical guidance is well worth its cost. The numerous difficulties and losses due to defects of various kinds arising from gas-metal reactions are now generally recognized and interest in these problems is widespread. The forthcoming A. I. M. E. round-table discussion of gas-metal problems will do much to clarify the situation and will permit us to assay our present knowledge and to suggest the proper direction for profitable future research. "The Age Hardening of Metal" was the title of the annual I. M. D. lecture delivered by Dr. Paul D. Merica. A critical review of the known facts relating to age-hardening phenomena was first given, followed by the presentation of a theory correlating the detailed observations which have been made regarding the mechanism of the hardening.

Jan 1, 1933

Jan 1, 1962

By C. W. Davis

THE name fuller's earth, which was derived from its early use in "fulling" or removing grease from woolen goods, is a term that is generally considered to designate mineral matter, containing hydrous aluminum silicates of the clay group, which has a high capacity for removing colors from oils, whether of animal, vegetable, or mineral origin. Fuller's earths are usually dried and may be "tempered" by heating or may be treated with water or reagents to improve their efficiency. For our purpose the term "acid-treated earths" will include those products from the partial decomposition of mineral water by acid which are equal to or more efficient than an untreated fuller's earth from Quincy, Fla., when used in bleaching mineral oil by the "contact" process. In general, the contact process for treating oils consists of heating and agitating a mixture of oil and finely divided adsorbent, the latter being subsequently removed by filtration. The term "adsorbent" is used because, although there has been a great deal of controversy over the mechanism of removal of impurities from oils by mineral matter, there is no doubt that adsorption, which involves the surface of the solid, plays a major part.1 The properties that make fuller's earth useful in the treatment of petroleum products by "percolation" and in the purification of edible oils by the contact process have long been studied, but the comparatively recent adaptation of the contact process to the bleaching of petroleum products has made desirable the further investigation of fuller's earth and other adsorbent earths.

Jan 1, 1929

By W. H. Hough, P. B. Leavenworth

Development in the Upper Texas Gulf Coast during 1943 resulted in the discovery of 11 new fields as compared with 12 discovered in the same area during I942. Of the 11 new fields, eight are classed as oil and/or condensate and three as gas fields. In addition to the new discoveries, several more or less important new horizons and extensions were encountered in some of the older fields, as noted in the text under the heading "New Pays and Extensions.'' Drilling During the year, 418 wells were drilled, as compared with 356 drilled during 1942. Of these, 323 were field wells, of which 188 produced oil, 21 were gas wells and 114 were dry holes. The remaining 95 viere wildcats, 12 of which produced oil, 4 produced gas and 79 dry holes. Distribution of themwildcats with respect to the various trends may be summarized as follows: over the 91,340,492 bbl. produced in the same area during 1942. The production statistics in the text and the accompanying tables include condensate or distillate as oil production, because many Gulf Coast fields produce oils with a wide variation of specific gravities, all of which are commingled in pipe lines. Table 3 shows by counties all of the drilling and production" data applicable to this particular area. Outstanding Fields of 1943 The Upper Texas Gulf Coast covered in this report has 178 more or less active oil and gas fields, including the 1943 discoveries. Of these Table 4 lists those that were most important from the standpoint of production. Each of these fields pro duced in excess of one million barrels of oil during 1943. Some of the interesting facts to be noted from this list of some 26 oil fields are: (I) four of the fields— namely, Conroe, Hastings, Friendswood and Thompson—each produced more than 10 million barrels during 1943, whcrcas Conroe and Hastings were the only fields that produced 10 million barrels during 1942; (2) some of the older fields (discovered prior to 1920), such as Barbers Hill, West Columbia, and Hull, are still producing in excess of one million barrels annually; (3) some of the fields more than doubled their 1942 production—e.g., Anahuac and Friendswood. The large increase in production in practically all instances is the result of increased allowables from wells drilled prior to 1943 and

Jan 1, 1944

By W. H. Hough, P. B. Leavenworth

Development in the Upper Texas Gulf Coast during 1943 resulted in the discovery of 11 new fields as compared with 12 discovered in the same area during I942. Of the 11 new fields, eight are classed as oil and/or condensate and three as gas fields. In addition to the new discoveries, several more or less important new horizons and extensions were encountered in some of the older fields, as noted in the text under the heading "New Pays and Extensions.'' Drilling During the year, 418 wells were drilled, as compared with 356 drilled during 1942. Of these, 323 were field wells, of which 188 produced oil, 21 were gas wells and 114 were dry holes. The remaining 95 viere wildcats, 12 of which produced oil, 4 produced gas and 79 dry holes. Distribution of themwildcats with respect to the various trends may be summarized as follows: over the 91,340,492 bbl. produced in the same area during 1942. The production statistics in the text and the accompanying tables include condensate or distillate as oil production, because many Gulf Coast fields produce oils with a wide variation of specific gravities, all of which are commingled in pipe lines. Table 3 shows by counties all of the drilling and production" data applicable to this particular area. Outstanding Fields of 1943 The Upper Texas Gulf Coast covered in this report has 178 more or less active oil and gas fields, including the 1943 discoveries. Of these Table 4 lists those that were most important from the standpoint of production. Each of these fields pro duced in excess of one million barrels of oil during 1943. Some of the interesting facts to be noted from this list of some 26 oil fields are: (I) four of the fields— namely, Conroe, Hastings, Friendswood and Thompson—each produced more than 10 million barrels during 1943, whcrcas Conroe and Hastings were the only fields that produced 10 million barrels during 1942; (2) some of the older fields (discovered prior to 1920), such as Barbers Hill, West Columbia, and Hull, are still producing in excess of one million barrels annually; (3) some of the fields more than doubled their 1942 production—e.g., Anahuac and Friendswood. The large increase in production in practically all instances is the result of increased allowables from wells drilled prior to 1943 and

Jan 1, 1944