Search Documents

Effect of Grinding Media on the Flotation of Sulfide Minerals

Sep 13, 2010

By J. Stacho, Frankovská. J.

"Abstract The use of continuous flight auger (CFA) piles in Slovakia has increased significantly in recent decades. High-rise building of administrative centre Lakeside Park in Bratislava is based on piled-raft foundation. The technology of CFA has been used due to the advantages of this technology in comparison with driven and bored piles in local geotechnical conditions. Piles have been designed in accordance with Eurocode 7. Resistance of piles was calculated by using an analytical calculation model for bored piles according to Slovak technical standard and CFA technology has been taken into account by coefficient equal to 1.1. Settlement of piles was calculated by using a calculation model which is being used in Czech Republic and Slovakia. Two well instrumented static load tests were carried out to verify the pile design. The results of static load tests showed that the design was conservative. The paper presents analysis of numerical modelling of CFA pile and static load tests. Load-settlement curves and load distribution curves over pile shafts are compared. Software Plaxis 2011 has been used for numerical modelling. Hardening soil model allows considering over consolidation of Tertiary Silts and water pressure in deep sandy lenses. The article also presents the parametric study where the influences of pile-soil interface reduction factor, over consolidation ratio and material models of soils are analysed. The results of numerical modelling showed that the most appropriate results have been obtained when the interface reduction factor equal 0.9 and real behaviour of groundwater were considered. The conclusion of the paper confirms that mechanical behaviour of the ground can be better understood and determined by using FEM than analytical methods.1. IntroductionPiles are among the most frequently used elements of deep foundations. Piles transfer loads down to a suitable bearing stratum when the soil immediately below a construction is unsuitable. Piles are also used to reduce settlement of structure. At present, the requirements of limit settlement of structures are more stringent. Examples of these structures are commercial and administrative centres that form a complex of different tall buildings. High-rise buildings cause greater contact stresses than connected low-rise buildings. Pile foundations in such cases should be placed under the high-rise buildings to achieve an appropriate settlement.Resistance of piles can be determined from static load test results, in-situ tests and empirical experiences or calculations. Static load tests give the most reliable results, but these tests are also the most expensive. This is the reason for constant development of computational methods. Especially numerical methods give more accurate results by using more sophisticated material models e. g. hardening soil or hypoplastic model."

Jan 1, 2014

By R. A. Williams

The Pascua Lama Project is situated on the border of Chile and Argentina at an elevation of 4,800 m. The ore contains gold, silver and copper, and an initial milling production rate of 33,000 t/d is planned. The mineralogy of this deposit is unusual. The ore is hard and abrasive, and it contains a complex array of sulphate minerals, such as chalcanthite, jarosites and alunites. The sulphides are predominantly enargite and pyrite. A novel flowsheet has therefore been developed, which includes dry grinding and ore washing to remove and then neutralize the soluble salts, prior to flotation, cyanide leaching and Merrill-Crowe recovery of the precious metals. These metallurgical issues and challenges associated with plant design and construction in the high and remote Andes Mountains make this a particularly challenging project.

Jan 1, 2001

By Clarence Karr

THE BUREAU OF MINES is investigating methods for upgrading tar produced by the low-temperature carbonization of bituminous coal. This survey was undertaken to compile information needed for identifying the ether constituents of low-temperature tar. Physical properties are listed for 1,024 aromatic ethers. The compounds include cyclic and noncyclic, polyfunctional and monofunctional ethers with oxygen joined directly to either one or two aromatic rings. Alkyl groups up through butyl are included. The compounds are divided into 37 groups ranging in complexity from alkoxybenzenes to dibenzopyrans. Compounds containing aromatic ether groups are important constituents of the neutral oxygen components of low-temperature tar. For example, at Morgantown, W. Va., the Bureau of Mines has identified and determined the amounts of benzofuran, 2-, 3-, 5-, 6-, and 7 -methylbenzofuran, diphenyl ether, dibenzofuran, 2,3-dimethyldibenzofuran, and two other dimethyl-dibenzofurans in the neutral oil from a low-temperature bituminous coal tar (103, 104).3

Jan 1, 1962

By H. D. Kline

This publication describes methods and techniques of mining and crushing limestone at 3 of 11 small quarries operated by Anderson-Oxandale Rock Co. in northeast Kansas in 1959. It is one of a series of reports by the Bureau of Mines on methods and costs of mining in various mining districts in the United States. The three quarries selected for study -Bosse quarry, Pottawatomie County; Hansen quarry, Morris County; and Huston quarry, Dickinson County (fig. 1) -were in many respects similar to many others that had been developed solely to fill local and usually transitory demands for crushed limestone for use as concrete aggregate, roadstone, and soil conditioning. Factors governing the choice of quarry sites were quality of limestone, shallow overburden, and proximity to points of consumption of the crushed stone.

Jan 1, 1962

The small-scale surface mining operation in northern regions is typically located in a remote, ungaged basin. With the recent increase in the economic potential of mining, the number of small operations is increasing. The year-to-year variability in precipitation in this region under study is of great concern to mine operators. Some years may yield only 5 to 6 inches of precipitation, while others may yield in excess of 15 inches. Such variability makes placer mining operations difficult to plan, since low water years may result in too little run-off for gravel washing and high water years may result in flooding of mining developments. There are no official streamfloaw records in many watersheds in the northern region containing placer mining claims. However, information from other streams permits calculation of an estimated discharge for a watershed under consideration using average flows per square mile of drainage. It is to be emphasized that these are average or expected figures in reality, one water year may be significantly wetter or drier than another. This high variability of annual precipitation is significant in relation to placer operations because of the large quantities of water required for this type of mining. Some operations can not operate in low water years. In the larger watersheds, operations may continue in low water years but at a slower pace because of longer water collecting times. The high variability of available run-off rakes placer mining in many parts of Alaska difficult to plan on a long range because of the unpredictability of water supplies.

Jan 1, 1985

By F. W. Lee

This paper purposes to outline briefly results of seismic measurements made in the vicinity of blasts in a mine and in open-quarry operations. It endeavors to examine the amplitude and frequency of such vibrations as influenced by the loading, geology, and distance from the source and includes comments on factors that may index the destructiveness of a vibration and a method for measuring the stresses produced. There seems to be no simple mathematical analysis of the transmission of seismic energy through the ground, and experimental observations are at present most feasible. SEISMOLOGIC INSTRUMENTS Instruments developed by the Bureau of Mines for recording ground vibrations from quarry blasting comprise a new type of seismometer, oscillators, and a recording oscillograph. The seismometers respond to vibrations reaching them through the earth and transmit their characteristics by electric current to the oscillograph, where they are recorded by a beam of light on a moving strip of sensitized photographic paper. The seismometers are so constructed that their sensitivity to earth vibration can be controlled, thus keeping the amplitude of the recorded wave within bounds on the paper. Each instrument has been calibrated against vibrations of known intensity and frequency so that correction factors are known for the idiosyncracies of each unit. Moreover, each seismometer is calibrated in the field for its particular sensitivity setting at each blast. By these controls the actual movement of the earth due to vibrations of one ten-thousandth of an inch can be accurately measured.

Jan 1, 1936

By H. K. Taylor, B. Denby, L. D. Smith

Contributions by H.K. Taylor and G.A. Davis discuss the three papers published in Transactions IMM A, vols. 103 and 104, with responses by Smith and Dowd

Dec 1, 1995

By Ian MacKenzie

Over the past twelve years, professionals such as architects, engineers, accountants, and attorneys have not had to pay a great deal of attention to GST. The fees charged to clients (outputs) have not been subject to GST, but they have had to pay GST on al purchases of materials and taxable services relating to their activities.

Jan 1, 1990

By Frank Otten, Jochen Greinacher

"In July 2017, Deilmann-Haniel signed a contract with IOO Slavkaliy to sink two 750 metre (m) deep freeze shafts for the Nezhinsky Potash mine in Belarus. This is the second shaft project where this technology is employed after two over 1,000 m deep shafts for a potash project in Saskatchewan, Canada, have been sunk by the application of the Herrenknecht Shaft Boring Roadheader (SBR) technology. Developed to sink shafts for green field projects in soft to medium hard rock, in frozen or unfrozen geology, the machine technology utilizes a roadheader-type cutterhead on a telescopic boom to mechanically excavate the rock, and a pneumatic mucking system to convey the muck from the face into the buckets. This leads to a manless face during the sinking cycle and thus a significant improvement in terms of workplace safety. For the Nezhinsky project, the SBR design was significantly modified in close cooperation between Deilmann-Haniel and Herrenknecht, based on the available experience and the special requirements of the project. Such modifications have been for example the adaptation of the Pneumatic Mucking System to cope with wet material as well as dry as originally planned or the shaft lining moving from shotcrete application to jump for and tubbing installation for which a step-change hands-off tubbing erector for the placement of segments was designed. Further modifications to optimize the machine technology for the requirements during shaft sinking were applied on the two machines for the Slavkaliy project as well as several revisions to match the special project requirements. The SBR is suitable for soft and medium hard rock up to 100 MPa UCS. The main design limits are maximum weight of the machine with 400 tonnes and length or height of 50 m due to the depth of the pre-sink. The Pneumatic Mucking System was changed in all components, sheaves and rope arrangement were redesigned and the concept of the hoist system was also re-engineered. The SBR in Belarus is configured for a daily sinking rate of three metres and all systems behind the cutting boom are not the bottle neck of the whole system. The works on site started in November 2017 including freeze hole drilling, construction works, site setup, installation of hoists winches, permanent headgears and other components required for sinking. The SBRs arrived on site in June/July 2018 and were preassembled on surface and then lowered into the 50 m pre-sink. SBR #1 started full face sinking in mid-December 2018, and SBR #2 in late January 2019. By the end of February 2019, the machines were at 150 m and 100 m depth respectively, and achieved up to 3.6 m/day concrete lined shaft. The SBR and the sinking system, the experiences, problems, technical solutions and performances of this challenging project will be presented in this paper."

Jan 1, 2019

By J. Crummy, I. K. Anderson, A. J. Hall, R. S. Haszeldine

Bedrock gold mineralisation has been located in association with an extensive float train 25 km west of known alluvial gold. It is in the form of open, matrix-supported breccias comprising pyritic quartz/sericite clasts in a vuggy, cherty chalcedonic and crystalline quartz matrix. Fluid inclusions in pyritic clasts indicate trapping temperatures for gold mineralising hydrothermal fluid of 170-240 degrees C. This mineralisation could represent the upper part of a feeder zone to an exhalative hydrothermal system. It is possible that other high-level feeder zones could be preserved elsewhere in the area. Deep weathering of such a system could provide a source for the alluvial gold localities near Helmsdale. It is suggested that east and central Sutherland presents good prospects for exhalative epithermal gold mineralisation and the associated feeder zones

Jun 19, 1905

By Dimitri Frantzos, Stewart Thompson, Ed Skiba, Hans Tammemagi

On behalf of Acres International we would like to thank Frank Chiappetta of Blasting Analysis International for inviting our organization to participate in this state-of-the-art course on blasting analysis techniques.

Jan 1, 1989

By Stefan Aronsson, K. Rainer Massarsch

"ABSTRACT The geology of Sweden is characterized by the most recent glacial period with deposition of very soft clays and loose sand. Due to these difficult geotechnical conditions, new, innovative foundation and ground improvement methods were developed, which today are used in many other countries. Over centuries, Swedish scientists and engineers have made important contributions to the developments in foundation engineering. An important aspect of the success of Swedish foundation engineering in practice is the spirit of close cooperation between practitioners, engineers, and scientists. This has been achieved by the establishing of commissions, with the aim of finding solution of geotechnical problems. The paper focuses on developments in foundation engineering during the last century and does cover present activities in Sweden.IntroductionSoil mechanics and geotechnical engineering play an important role in Swedish society, as most construction activities require the consideration of foundation conditions. The objective of the paper is to summarize important developments in foundation engineering, primarily during the past century, which have influenced geotechnical engineering also in other countries. These achievements are the result of contributions by scientists, engineers and practitioners, only a few of which can be named. The paper does not claim to cover all aspects of geotechnical engineering, as emphasis is on the solution of foundation engineering problems from an international perspective. Thus, ongoing or recent research and development projects and activities within the geotechnical community are not included, as this would exceed the scope of the paper.Over the centuries, Swedish scientists and engineers contributed to the development of civil and foundation engineering. One important reason is the geology of Sweden, which is characterized by the most recent glacial period, resulting in the deposition of soft clays and loose sands in the coastal areas and dense glacial till in the interior of the country. Geotechnical engineering in Sweden has a long tradition and early contributions by several Swedish engineers and scientists have had a profound influence on the current foundation design in and beyond Sweden. A description of early Swedish geotechnical engineering has been presented in several publications by Flodin and Broms (1981), Broms and Flodin (1988), Massarsch and Fellenius (2012). The historic development of Swedish geotechnical and foundation engineering can be divided into four periods. During the “Early Era”, engineers were active in different sectors of military, civil, and mining engineering. Next, the “Industrial Era” comprised developments during the industrial revolution, when the transportation infrastructure of the country was modernized and extended. During the third period, possibly the “Golden era” of Swedish geotechnical engineering, which started at the end of the 19th century and lasted the following fifty years, geologists, engineers and scientists helped to establish modern geotechnical engineering. But also during the recent past, the “Modern Era”, several important contributions to geotechnical and foundation engineering which originated in Sweden, are used in many countries today."

Jan 1, 2014

By Tim Q. Haldane

The ability to efficiently process lowgrade ores has allowed the Gold Fields Mesquite Mine in Imperial County, CA to expand from a 2.1 Mt/a (2.3 million stpy) rate in 1986 to its present 7.3 Mt/ a (8 million stpy) processing rate. Increased tonnage demands led to the 1989 construction and startup of a dump leach pad to supplement the existing heap leach operation. This resulted in an excellent opportunity to compare the two processes at the same operation. Additional operating costs associated with the crushed ore heaps are justified through enhanced recoveries, even at very low ore grades. Gold Fields' Mesquite Mine is a gold heap leach facility located about 55 km (35 miles) east of Brawley in southeastern California. Five open-pit mines will be developed over the projected life of the property, covering a total area extending to a maximum of 5.5 km (3.4 miles) to the east and west, and 2.4 kin (1.5 miles) to the north and south. Mesquite will process 7.3 Mt (8 million st) of ore and produce more than 6.2 t (200 000 oz) of gold in 1990.

Jan 1, 1990

By K Cameron, S Strohmayr, J Wallace

In 2012, a single module heavy medium cyclone plant (HMP) was installed at the Glencore Zinc’s (then Xstrata Zinc) McArthur River lead zinc mine. The HMP formed the first part of the MRM Phase 3 Project to increase run of mine (ROM) capacity from 2.4 to 5.5 Mt/a.The purpose of the HMP is to remove liberated gangue from the crusher product at minimal loss of valuable mineral. The McArthur ores are very finely disseminated requiring a fine primary grind size prior to rougher flotation. Rejecting waste prior to grinding therefore offers significant power and grinding media savings. The plant was designed to treat only those ores with a reasonable upgrade ratio at the target zinc recovery across the HMP of 95%.On this basis, a 1.8 Mt/a single module plant was built based on 250 t/h feed rate and 82% availability. In contrast to existing base metal heavy medium plants in Australia, the MRM Flow sheet utilised the principles in modern coal heavy medium cyclone plant design. Since commissioning, the plant feed rate has been significantly increased and is now normally operated up to 540 t/h (dry basis).Although this throughput increase is partially due to debottlenecking work, it is also attributable to the conservative design parameters for base metal heavy medium cyclone circuits in comparison to those used in equivalent coal circuits.This paper discusses Flow sheet design and compares traditional base metal design parameters with those achieved at MRM and those of modern coal plants. It provides information on plant capital and operating costs and the net savings realised by its installation. In addition to power and grinding cost savings, the paper also highlights the savings in water through rejection of near dry waste and reduction of tailings pumped to the storage dam.CITATION:Wallace, J, Strohmayr, S and Cameron, K, 2015. McArthur River Mine heavy medium plant – the benefits of applying modern coal plant design principles to base metal heavy medium separation, in Proceedings MetPlant 2015, pp 311–323 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 7, 2015

By D. Large, M. H. Davies, B. Driedrichs, U. Matzander

Synthesis report on a project carried out under the EC-funded BRITE-EURAM programme. A prototype high-resolution electromagnetic system, based on the theory of controlled-source magnetotellurics, was developed. The electrical source field is fed into the earth by dipoles at preselected frequencies and a multi-channel receiver measures five electric and three orthogonal magnetic fields. Suitable mapping algorithms and spatial filters are applied to the data and a new technique permits calibration during measurement. The system was field tested over a blind orebody, at 250-550 m depth, in the Aguas Tenidas area of the Iberian Pyrite Belt. Ten lines totalling 12 000 m of profile length were completed in seven days and the orebody was identified. Tests in the Irish Midlands suffered from strong electromagnetic interference of cultural origin

Jun 21, 1905

By R. Bergstrom

The implementation of a Quality Management System (QMS) or an Environmental Management System (EMS) that conforms to the standards issued by the International Organisation for Standardisation (ISO) no longer needs to result in a bureaucratic nightmare supported by mounds of paperwork. In this sense, this paper describes the Quality Management System that was implemented and demonstrates how the technologies that were developed can be used to satisfy other similar requirements.

Aug 25, 2002

By Y. Guglielmi, C. Gout, P. Henry, P. Dick

The key questions about fault reactivation in shales concern the potential enhanced fluid displacement through a previously low-permeability aseismic shale formation. Here we selected a critically-stressed fault cross-cutting the underground research facility of Tournemire (France) which is located in Toarcian shales. Several inclined boreholes were drilled across the 8.5 m thick fault zone characterized by a fractured damage zone (FDZ) and a central 2.4 m thick complex core (FC) made of multiple shear bands with gouge intercalated with highly fractured lenses. The fault was pressurized using a straddle packer system defining a 2.4m long injection chamber normal to the fault surface. Three fault zone intervals were tested, two in the fault damage zone and one in the fault core. A three-dimensional displacement sensor set in the chamber allowed continuous synchronous coupled monitoring of fault movements, injection pressure and flow rate. An anticlockwise 0.22-to-0.05 mm fault slip was captured associated with a 10-to-100 hydraulic aperture increase of the fault. Preliminary analyses of the experiments show that leakage in the fault zone is controlled by strength and stress magnitude contrasts between the fault core and the fault damage zone. Fault damage zone discontinuities display a much higher peak static friction angle than the fault core shear zones, respectively of 34 and 22° that could be related to complex interactions between healing and sealing processes. Fault core leakage is much more dependent on strain than on effective stress variations. Discontinuous, pulse-like leakage, develops following complex failure processes that may simultaneously take place in the gouge zones and along the large pre-existing discontinuities. Such results may be of importance in evaluating fault seal integrity in oil and gas exploration, production or CO2 storage or underground excavations monitoring.

Jan 1, 2015

By Fabian Mohr

The methyl substituted binuclear cyclometallated gold(I) complexes [Au2(?-n-MeC6H3PPh2)2] [n = 4, 5 and 6] all undergo oxidative addition reactions with halogens and, in the case of the 4- and 5-methyl substituted analogues, with dibenzoyl peroxide to give metal-metal bonded digold(II) complexes [Au2X2(?-C6H3-n-MePPh2)2]. The 4- and 5-methyl substituted digold(II) compounds on warming or exposure to light undergo carbon-carbon coupling reactions to give gold(I) complexes containing the corresponding 2,2'-n,n'-biphenylyldiphenylphosphines. The 6- methyl substituted digold(II) complexes rapidly isomerise above ca. -20° C to binuclear heterovalent gold(I)/gold(III) compounds [XAu(?-2-Ph2PC6H3-6-Me)AuX{?2-(6-MeC6H3-2-PPh2)}], containing a fourmembered cyclometallated ring on a gold(III) centre. Surprisingly, no carbon-carbon coupling could be induced for any of the 6-methyl substituted compounds, even under forcing conditions. This difference in reactivity of the 6- methyl derivative, compared to that of the 5-methyl and unsubstituted analogues was studied by ab initio calculations using a series of model compounds. The results are in excellent agreement with the experimental findings and suggest that the key-step in the C-C coupling reaction is the partial opening of the Au(III)-P bond in one of the transition states. In the 6-methyl system this transition state is energetically inaccessible and hence no C-C coupling occurs.

Oct 1, 2003

By Rajni Patel, John McDonald, Steve Dubnewych, Michael McKenna

The Upper Reach segment of the Northeast Interceptor Sewer (NEIS) is a3.2-km-long tunnel excavated in interbedded marine sedimentary deposits with approximately 40 m of cover. The tunnel was initially classified by Cal/OSHA as “potentially gassy.” During excavation, high levels of hydrogen sulfide and methane were encountered, prompting Cal/OSHA to reclassify the tunnel as “gassy.” In addition, the tunnel excavation encountered an abandoned, 100-year-old water tunnel known as the “Narrows Gallery.” This existing tunnel was completely full of water and under 30 m of hydrostatic head. This paper will discuss the unanticipated difficulties and design solutions implemented to construct a gassy tunnel exposed to high volumes of water.

Jan 1, 2005