Search Documents

By Wallace W. Key

This report concerns types, quantities, specifications, and uses of non-metallic minerals as a basis for improving their supply, conservation, and utilization. Supply-demand details concerning mineral fillers, roofing granules, and roofing rock used in asphalt are incorporated in this report, along with highlights on production and sales of roofing, floor tile, and other related asphalt products of California. Comparable data for the United States are included. Although large quantities of commercially prepared mineral fillers are used in asphalt for paving and related applications in other States, addition of commercial fillers for these uses rarely is required in California because of the natural fines available. On the other hand, California manufacturers of asphalt products other than paving utilize about 300,000 tons of asbestos, diatomite, limestone, mica, soapstone, slate, and other nonmetallic minerals as filler, mainly for roofing and flooring. Also, about 500,000 tons of roofing granules is produced in California, most of which goes into roofing manufacture in California. In addition, a significantly large and growing tonnage of relatively coarse mineral aggregates are used on low-angle, built-up, asphalt roofs to produce an attractive surface and offer protection against the elements. Nearly all minerals used in asphalt products manufactured in California come from local sources, except asbestos and mica--and there are indications that local deposits of these commodities could be utilized in some use categories.

Jan 1, 1966

By S. Rupprecht

"This article addresses the prevalence of poor public reporting practices of coal exploration results, coal resources and coal reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or saleable tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal — therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (ROM) and saleable coal tonnage, their associated qualities and other material and relevant information.Competent or qualified persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provided. “Companies are encouraged to provide information in their public reports, which is as comprehensive as possible (CRIRSCO, 2013).” However, too often this isn’t the case, and material matters are either not reported or inadequately disclosed.According to the South African National Standard (SANS) 10320:2014 draft document, “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the saleable coal reserve must be stated. The moisture basis of reporting shall be stated.” An example as to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are detailed in the followint paragraphs. The Kendal power station, commissioned in 1988, operates at a calorific value (CV) range of 19 to 20 MJ/ kg, an ash content between 29 and 34 percent and volatiles between 20 to 21 percent. Other power stations, such as Kriel or Hendrina, may require different qualities, such as a CV range of 22 to 23 MJ/kg, an ash content between 20 and 28 percent and volatiles between 22 to 23 percent. Thus, in terms of domestic saleable coal, it is not just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station (Chetty, 2010).” Sulfur content is another important quality with the ideal coal content having a quality of less than 1 percent sulfur."

Jul 1, 2019

By F. Dieu, C. Laughton

CERN, the European Laboratory for Particle Physics, is, at present, constructing an underground tunnel and cavern network to house a Large Electron Positron (LEP) colliding beam machine. This paper describes the techniques adopted to permit the excavation and temporary support of the access shafts through a series of glacial moraines, at depths of up to 80 m, to reach the bed-rock. Owing to the presence of superficial and deep water-tables, the variable nature of the moraine deposits and, above all, the tight work schedule, a combination of diaphragm walling and ground freezing was employed.

Jan 1, 1987

By Alejandro Ferrada Vergara

Most blasting techniques that are designed to improve fragmentation and subsequently improve ore work index to downstream comminution processes, apply powder or energy factor increases, either by stretching the drilling pattern (burden/spacing ratio) implementing faster initiation sequences or using more energetic explosives. The new application will move detonation parameters up, making the blasting process riskier for the surrounding boreholes, explosive column or initiation systems functioning.

Jan 1, 2016

By Conny Postupack

The first principle one usually learns about blasting is that competence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced in a new area, may have co make one or two himself to the new conditions with which he blaster when operating shots just to acclimate is faced.

Jan 1, 1991

By G. Swan, E. Nordlund, P. Zhang

"SynopsisThe most widely used support design damage criterion for rockburst-prone mines is based upon kinetic energy, which is proportional to the square of the ejection velocity and is commonly expressed in terms of peak particle velocity (PPV). Field monitoring and back-analyses have shown that ejection velocities of the order of 10 m/s and higher can result from seismic events of moderate magnitude. Such velocities are much higher than those predicted using PPV obtained from scaling laws. It has also been found that the peak ground motion (i.e. PPV) on the surface of an excavation is preferentially amplified (by four- to tenfold) compared to the motion in solid rock at a similar distance from the source. However, the wave propagation and interaction processes involved within the fractured rock in generating high ground motion are very complex and are not well understood at this time.In this paper, velocity amplification was investigated by modelling the dynamic interaction between fractured rock and a free surface using a 2D discontinuum-based numerical program, UDEC (Universal Distinct Element Code). A 1D model with a fractured zone was used to represent the fractured rock. Velocity amplification, quantified by PPV, predicted at the free end of the model was 2.0–3.6 times higher than the input velocity. It was found that the wave frequency, fracture stiffness, fracture spacing, and thickness of fractured zone are the main factors that affect the velocity amplification. The results have proved that the interaction of the seismic wave and multiple fractures near the free surface strongly influences the ground motion.IntroductionSince mining-induced seismicity is almost inevitable in deep mines, ground support is generally employed to mitigate the risk of seismically-induced damage. The most widely used support design criterion for seismicallyprone mines is one that seeks to maximize the absorption of the kinetic energy (plus potential energy if a gravity component is considered) of key rock blocks. Based on this criterion, design methods for rock support were first proposed by Wagner (1984) in South Africa and later improved, among others, by Roberts and Brummer (1988) and Kaiser et al. (1996)."

Jan 1, 2015

By Allan Sylvester

Construction of the Shot Tower Metro Station in Baltimore, Maryland was performed in two phases. In the first phase, a contractor was retained to excavate the station in order to construct twin tunnels from the Shot Tower Station to the John Hopkins Station. The retention system for this 70' deep excavation consisted of a Soldier Pile in Tremie Concrete (SPTC) wall supported by cross-lot bracing. In phase two, The Clark Construction Group, Inc. was retained to construct the station interior structure, two entrances, two station ancillary shaft structures and the track work for the station and tunnel. The excavation for the construction of the two entrances adjacent to the 70' deep station SPTC wall had to proceed prior to completion of the station structure due to the tight construction schedule. A system of overlapping secant piles was specified as a vertical support of excavation element for the West Entrance. The secant piles would have provided a watertight, rigid support to resist the load from the SPTC wall constructed in phase one. A watertight system was required in order to minimize the settlement of adjacent buildings supported on wood piles. Clark Construction was concerned with the constructability, cost and performance of the specified secant piles and looked for other innovative methods of providing a watertight and rigid system. Substitution of a reinforced slurry wall in lieu of the secant piles was cost prohibitive due to the additional cost of concrete placed under tremie. Clark, being familiar with cement-bentonite cut-off walls and slurry wall construction procedures, proposed the construction of a PSHG wall, in lieu of the secant piles. The PSHG wall construction consisted of trenching 30" wide by 20' long by 60' deep panels under a self-hardening slurry. Once the excavation for a panel was completed, a 60' deep prefabricated soldier beam and lagging panel was placed in the slurry. The slurry design mix then self-hardened within the cure time, allowing excavation for the structure to proceed This paper will discuss the design, details and construction methods used on the PSHG wall and will compare the advantages of the PSHG system to conventional support systems.

Jan 1, 1997

By K. Zeidler, T. Schwind

The Fort Canning Tunnel, Singapore, is an approximately 50 feet (15m) wide vehicular tunnel under shallow ground cover that has been constructed according to the principles of the NATM. Its shallow location in soft ground combined with a high groundwater elevation in close vicinity of historically important features called for special design considerations combined with a rigorous monitoring scheme. Surface, sub-surface and in-tunnel instrumentation was installed to monitor the performance of the ground and tunnel support during construction. Comparison of actual reading data with the results from the computer modeling carried out during the design phase is provided in this paper.

Jan 1, 2007

By R. Q. Honaker, D. P. Patil, A. Sirkeci

Due to increased production of fine coal during mining during this century and inefficient fine coal recovery technologies, a vast reserve of high quality coal currently exists in refuse ponds. A novel fine coal circuit consisting of a hindered-bed classifier, an enhanced gravity concentrator and a flotation column has been evaluated for the recovery of fine coal from refuse ponds. The treatment of a pond derived from Pittsburgh No. 8 seam coal resulted in the production of a premium fuel containing less than 5% ash and a calorific value of about 30,173kJ/kg with 60% mass yield. The results from the treatment of two refuse pond materials will be presented in this publication.

Jan 1, 2000

By John L. White

Vibratory driver/extractors do more than drive and extract sheet piles. I would say more than sixty percent (60%) of the time, vibratory pile driver/extractors are engaged in work that has nothing to do with sheet piles. This is the main reason I refer to this tool as a "driver/extractor", and omit the word "pile". I have spent the last twenty years applying the technology of the vibratory driver/ extractor to all areas of foundation construction. As you will see, the only limits are humankind's ingenuity.

Jan 1, 1997

By B. A. Eaton

The subject of many discussions and technical papers in the last 20 years has been the prediction of the well-bore pressure gradients that are required to induce or extend fractures in subsurface formations. The subject merits this attention because of the frequently recurring problems that arise from an inability to predict fracture pressure gradients. Encountered in several common types of operations in the oil industry are problems associated with the prediction of formation fracture pressure gradients. When wells are being drilled in both new and old fields, lost circulation is often a very troublesome and expensive problem. Complete loss of circulation has been disastrous in some cases. Many times, such disasters could have been avoided if techniques for calculating fracture pressure gradient had been employed in the well plans, and if casing strings had been set, and mud weight plans had been followed accordingly. In areas of abnormally pressured formations, the prediction of fracture gradients during the well-planning stage is extremely important. In fact, it is as important as the prediction of formation pressure gradients, which has received a great deal of attention in recent years. There are several published methods used to determine fracture pressure gradients. However, none of these methods appears to be general enough to be used with much reliability in all areas. In 1957, Hub-bert and Willis published a classical paper that included the development of an equation used to predict the fracture extension pressure gradient in areas of incipient normal fau1ting.l Overburden stress gradient, formation pore pressure gradient and Poisson's ratio of rocks were the independent variables that were shown to control fracture pressure gradient, the dependent variable. In 1967, Matthews and Kelly published another fracture pressure gradient equation that is different from that of Hubbert and Willis in that a variable "matrix stress coefficient" concept was utilized.3 Later the same year, Costley wrote about a similar idea.5 Goldsmith and Wilson used a least-squares curve-fitting technique and field data from the Gulf Coast area to correlate fracture pressure gradient with formation pore pressure gradient and formation depth.' They noted that the fracture pressure gradient increased with increasing depth while the pore pressure gradient remained constant. In each of these cases, the problem for which a solution was sought was to determine the bottom-hole pressure gradient required to initiate or extend a fracture. Results of the previous work show that fracture pressure gradient is a function primarily of overburden stress gradient, pore pressure gradient, and the ratio of horizontal to vertical stress. There is argument for a fourth variable in that in many cases breakdown fracture pressure gradient is greater than the fracture extension pressure gradient. However, if the fracturing fluid is able to penetrate the formation through the pores or existing cracks, there is very little

Jan 1, 1970

By W. Dan Hausel

More than 220,000 diamonds have been found in the United States that range from microdiamonds to 40.42 carats in weight (Table 1). Some reports suggest diamonds weighing more than 100 carats have also been found in this country, although these reports have not been verified. The source of most of the diamonds in the United States is a group of kimberlite pipes, dikes and blows in the Colorado-Wyoming State Line district and a group of lamproite pipes in the Murfreesburo, AR area. Other areas where diamonds have been found include the Great Lakes region, the Pacific Coast and the southern Appalachian Mountains. The latter two regions are generally not considered favorable for diamond deposits. This is based on exploration models. They suggest commercial diamond deposits will be restricted to kimberlites emplaced in Archean cratons and to lamproites emplaced in Proterozoic mobile belts accreted to the cratons.

Jan 1, 1995

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents preliminary test results obtained with a 0.38 kg/s (3000 lb-hr) beta prototype MagMill™. In processing Upper Freeport coal the beta prototype recovered 82% of the weight of the feed and 91% of the heat content while reducing the potential emissions of sulfur, kgSO2/GJ(lbSO2/MBtu), by 61%. Pyritic sulfur in the MagMill™ product was reduced by 78% compared to that in the feed. For all runs, the mill product was controlled between 70 to 80% finer than 74 µ particle size. Recoveries of mercury, arsenic, and selenium ranged from 35 to 45% of that in the feed. Power draw was reduced by 26% and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2000

By Miezitis Y

A weak airborne radiometric anomaly was examined in the field and the presence of uranium confirmed. Rotary-percussion drilling showed the presence of uranium but a subsequent programme of diamond and rotary percussion drilling indicated that the concentration of uranium was uneconomic. Within the tufts and volcanics of the prospect the uranium existed as uranyl phosphates within the oxidized zone. Geological mapping and the diamond drill core showed that the Stag Creek Volcanics are part of the Lower Proterozoic Masson Formation, probably with member status, rather than the expression of an Archaean basement ridge. This change in the interpretation of the fundamental structure of the Pine Creek Geosyncline has led to a reexamination of the stratigraphy and to suggestions which differ from the current concept.

Jan 1, 1977

By R. W. Van Dolah

A premature detonation of an explosive charge occurred on January 30, 1961, at a face being prepared for blasting in the underground Jefferson Island Salt Mine, Diamond Crystal Salt Co., Jefferson Island, Iberia Parish, La. The accidental blast injured the powderman fatally; his helper was injured also, but recovered. The accident represents the first fatality reported to the Bureau of Mines in connection with the use of ammonium nitrate-fuel oil (AN-FO) blasting agents in underground mining in the United States. Representatives of the Bureau of Mines Explosives Research Laboratory, Pittsburgh, Pa., and field representatives of the Bureau's Health and Safety Activity conducted the investigation, upon request of the manufacturer of the ammonium nitrate being used and with concurrence by the mine management.

Jan 1, 1962

By K. P. Wright

"Twenty-five years ago, there were about thirty-two gold mines operating in Canada; nine of these have been in continuous operation since then and are still operating. Three of these are part of the Dome Group. Operations of these three and of the newer mines in the Group are referred to in discussing process development over the last twenty-five years.Of the Dome Mines Group, Dome Mines Limited, Sigma Mines (Quebec) Limited, Campbell Red Lake Mines Limited, Detour Lake Mine and Kiena Gold Mines Limited, three have been in continuous operation for the last twenty-five years. Dome has operated for seventy-seven years; Sigma about to complete fifty years, and Campbell approaching forty. Overall, milling processes are virtually the same as they were twenty-five years ago. Tota1 go1d production from the three mines has hardly changed; 1960 production, 416,700 ozs. versus 411,300 in 1985. Milling costs have risen by a factor of six or seven and gold price from $35/oz. in 1960 to $322 in 1985.Basic flowsheets are relatively unchanged. Sigma is an all cyanidation mill grinding in cyanide solution; Dome operates gravity concentration and cyanidation; Campbell gravity concentration, flotation, roasting and cyanidation. All three use Merrill-Crowe zinc precipitation.Detour and Kiena are two examples of the major change in gold processing in the last twenty-five years - carbon-in-pulp. This process has brought along with it other changes, such as, carbon stripping and reactivation, electrowinning, and induction furnace melting. Modern mill design with its use of outside thickeners and agitators, bulk handling of reagents, instrumentation, etc., has made a radical change in operating conditions and appearance of the new plants."

Jan 1, 1987

By R. J. Watson, A. H. Juch

About half a million sucker-rod pumps are installed in oil wells in the U. S. alone. In Venezuela, too, the system is widely used; some 5,000, or 90 percent, of Cia. Shell de Venezuela's wells produce a total of 400,000 BOPD by this method. Most of the crude pumped is viscous, gassy and contains relatively small amounts of free water. API gravities vary from 90 to 16O; dead oil viscosities vary from 10 to 10,000 cp at the pump; and GOR's range from 100 to 2,000 cu ft/bbl. Pumps are set at depths ranging from a few hundred to 6,000 ft; the average setting depth is about 2,500 ft. From the literature, it appears that although recent years have seen significant progress toward understanding the rod pumping system as a whole, relatively little attention has been paid to those key items, the sucker-rod pump and the subsurface gas separator or gas anchor. Perhaps because of proration in the U. S., pump manufacturers have seemingly concerned themselves more with the durability of their product, achieved mainly through robust design and metallurgical know-how, than with its working efficiency. In 1963, CSV commenced a major rehabilitation and expansion of its heavy oil fields along the Bolivar Coast. The advent of the more efficient gravel-packed completion and of large-scale thermal recovery (mainly steam soak) operations resulted in well potentials *Now with B. I. P. M., The Hague, The Netherlands. greater than pump capacities. Hence, an urgent need arose to improve over-all pump efficiencies and to attack those special problems related to the production of both the extremely viscous and the hot, steam-laden crudes that formed an increasing proportion of the total stream. There followed a detailed investigation and testing program, carried out in close cooperation with a major pump manufacturer. This culminated in the introduction to the oil industry of a new line of sucker-rod pumps. Early Investigations and Experiments Field Tests Extensive field tests were carried out in three primary Bolivar Coast wells with an in-situ dead oil viscosity ranging from 400 to 6,000 cp. In these installations provision was made to (1) monitor bottom-hole pressures below, in and above the pump by means of pressure transducers, and record casing- and tubing-head pressures continuously; (2) measure accurately the annulus gas, as well as measure the tubing gas and liquid production from the well; (3) take special PVT samples of the well fluid; (4) measure power consumption of the prime mover; and (5) measure the rod loads at the polished rod. A typical test installation is illustrated in Fig. 1. It was established from the pressure transducers that with viscous oils, there is considerable flow resistance across the pump and gas anchor assembly. Pressure surges were observed over each pump cycle,

Jan 1, 1970

By H. Antrekowitsch

The decreasing quality of the input materials in copper recycling leads to a higher content of impurities in the anode copper. An improvement of the pyrometallurgical refining process is therefore necessary to produce high quality anodes for the copper refining electrolysis. The behaviour of the most important accompanying elements (e.g. nickel, tin, lead, zinc etc.) at different reaction conditions has to be investigated in order to improve the metal/slag reactions as well as the vaporisation by selective oxidation in the anode furnace. Therefore the thermodynamic conditions like reaction order and the activity coefficients at the copper refining process have to be known for the optimisation of this technique. Additionally the interaction between different elements has been investigated as a function of the temperature, the content of the elements and the slag composition especially for nickel. These investigations were done at the Christian Doppler Laboratory for Secondary Metallurgy of Nonferrous Metals.

Jan 1, 2005

By Vinícius Resende Domingues, André Pacheco de Assis, Bernardo Cascão Pires e Albuquerque

"The increasing demand for underground works in urban centers, and in particular the need to build undercrossing tunnels, requires constant evolution in building techniques in order to achieve success and safety. In the case of Brasilia, capital of Brazil, in order to preserve an important avenue (Eixo Monumental), where are located many historical monuments, the construction of a tunnel was envisioned as an option to interconnect the National Stadium (on one side of the avenue) to the Convention Center Ulysses Guimarães (on the other side). The excavation design is comprised of a coverage smaller than one diameter, height of 7.5 m, width of 9.0 m and length of 25 m. In order to enable a negligible influence on the avenue’s usage, the structure is designed as a portico system composed of pipe canopy. In this context, this study presents the portico analytical solution computed with the aid of the software Mathematica and a numerical solution using the software ABAQUS. INTRODUCTION Undercrossing tunnels are increasingly common in urban centers as alternative roads or as access to underground works of large dimensions (stations and parking lots). The geomechanical conditions of the soil mass, not always favorable, and the low distance between tunnel’s ceiling and the surface require intense treatment of the soil massif and execution of a rigid support system. The importance of the road just above the undercrossing tunnel emphasizes the need for a highly competent monitoring system because existing structures require minimum allowable displacement and do not allow the interruption of traffic. The soils that are excavated for the construction of undercrossing tunnels are composed, in most cases, of layers of fill and / or soft soil or weak rock, showing stability problems when subjected to tunneling operations. The combination of low coverage and week ground is solved by soil improvement techniques and strengthening of the excavated cross-section with further advance with the so-called New Austrian Tunneling Method (NATM). Another option is to build structural frames that support the surface. In this research, and based on the context of a case study, we propose the study of the construction technique comprising a portico structure composed of pipe canopy. For this paper, the technical standards used are the Brazilian ones as the case study refers to this country."

Jan 1, 2016

By Xinquan Zhou, Rudolf E. Greuer

MFIRE, written in Fortran 77, is a computer program for ventilation state simulation in the steady state or transient state condition. It can be applied for the calculation of normal ventilation system planning or the analysis of the dynamic state variation in a ventilation system under thermal or mechanical disturbance. The state simulator MFIRE is a useful tool for mine fire fighting. In the case of a mine fire, mine ventilation engineers want to get some help to obtain more information, such as what is happening in the underground mine and how to control the mine fire, for correct decision making. By use of program MF'IRE, forecasts can be made on the variation of airflow, temperature, and contaminant distribution in a ventilation system during a mine fire. The paths which the contaminant takes at each time interval can be traced. The program MFIRE can be of assistance in the preplanning of escape routes. It can also be helpful during a mine fire emergency and mine recovery operation. Besides of offering the information of state simulation during a mine fire, MFIRE can be applied for state control by pretesting the suitability of the selected state control measures. It is to simulate the effects of the state control measures on the airflow distribution of a dynamic ventilation system. The testing result can be used for fire fighting in a similar real case of a mine fire. By employing empirical methods or a qualitative analysis like Budryk approach, ventilation engineers can choose different combinations of locations and sizes of control devices as samples of state control for an underground mine fire. Program MFIRE can simulate the different combination samples, that consist of a certain mine fue, the corresponding different control measures, and obtain the control effects. After the different control results are compared, the state control measure, which creates the best effect among the different state control measures, will be chosen for that fire case. When a mine fire, which is similar to one of the pretested cases, breaks out, the corresponding choice of the state control measure is applied to the ventilation system. It means that the simulator MFIRE has the function of indirect state control [10]. To achieve the above two functions, state simulation and state control, the mine ventilation system condition, sometimes, should be changed in a wide range to meet the requirement of the fire fighting. These wide system condition changes, such as adding operating fans, stopping or reversing fans, changing fan characteristics, adding regulators and making airflow shortcuts are represented in the time table of the input data set When the data files are changed in a wide range, however, an iteration divergence and some other computing errors in the distribution of airflow, temperature, and contaminant may occur. More serious logical programming and flexible selection on the algorithms are wanted to meet the request of the different data sets, to achieve correct state distribution simulation and improve the iteration convergence. To enhance the reliability and common suitability of program MFIRE, it is necessary to make investigation, analysis, and modification for the formal versions of MFIRE. The version 1.29, permitting dry .calculation, and versions 2.01/v2.0, permitting dry and humidity calculation, are widely applied