Search Documents

By K. M. Kim

A site-specific blasting model has been developed for the Asarco Mission mine. The main inputs to the model are the in-situ block size (F80), the post-blast fragmentation (P80) and the intact tensile strength (To). The output from the model is the specific blast energy (ESE). Modern techniques are being used to obtain the input parameters for the site-specific blast fragmentation model. In particular, image processing software is used to obtain both the in-situ block size and the post-blast fragmentation, and the Schmidt hammer is used to obtain the tensile strength at numerous locations throughout the rock mass. An initial model was developed using five test shots in one area of the mine that contains Argillite and is relatively homogeneous. This also included calibrating Schmidt hammer readings against actual Brazilian tensile measurements. The model for Argillite will be updated as more tests are conducted, and the model will be extended to the other four primary rock types at the Asarco Mission mine.

Jan 1, 2011

By D. L. Cluff

Ventilation Air Methane (VAM) is a high volume low concentration methane source. The capture or use of methane from VAM is challenging, which results in the routine discharge of methane into the atmosphere. Mitigating VAM has the benefits of providing an energy source and reducing the atmospheric Greenhouse Gas (GHG) burden. The GHG radiative forcing effect of methane is 17?23 times as potent as carbon dioxide on a 100-year time horizon. Thus, any reduction in atmospheric methane would be beneficial. The calorific value of methane is 55.5 MJ/Kg; therefore, a 100 m3/s flow with VAM concentrations from 0.1?1% can provide 3.8?38 MW of exploitable power. Strategies to mitigate VAM such as: Thermal Flow Reverse Reactors (TFRR), Catalytic Flow Reverse Reactors (CFRR), Lean Burn and Catalytic Gas Turbines, Biothermica Vamox®, Megtec VOCSIDIZER©, and Vamcat? are briefly reviewed. The review of VAM mitigation technologies reveals disadvantages such as the need to maintain a minimum internal heat capable of oxidizing the methane. This requirement uses all of the available methane up to the point of reaction sustainability and up to half at the highest methane concentration in VAM. Some systems may introduce a pressure drop to the ventilation system, which would impinge on the existing ventilation system design. These impediments necessitate the development of a more amenable technology. In the proposed system, gas turbines (GT), coupled to a combustion chamber with an external fuel supply, assist the combustion of the VAM. The combustion-chamber coupled system provides electricity, while the heat contained in the GT exhaust gases increases the temperature of the VAM, encouraging the development of a flame inside a combustion chamber. The flow from the combustion chamber streams through a primary air/fluid heat exchanger capable of producing steam of a high enough quality to generate electricity using conventional steam turbines. The residual heat after primary extraction, directed through other equipment, provides additional heat based products such as industrial scale dry air, chilling by an absorption chiller or hot water. The overall design of the system is scalable for low to high VAM flows or variations in concentrations and is capable of providing the company or community with heating, chilling, hot water, electricity or motive force as needed by the particular site or community. The Multi-generation system uses heat from three sources to provide clean efficient energy while mitigating the atmospheric emissions of methane. These sources are heat from the GT, often considered waste heat, heat from fuel injected into the igniters and heat from the VAM. The opportunity to collect carbon credits may improve the economics. In order to design a system with this capacity, a detailed analysis of the combustion characteristics of three separate flows is required. VAM is the main airflow, having the highest volumetric effect, while the GT exhaust and the additional fuel added to the hot exhaust flow of the gas turbine are lower flows, but have a higher velocity and temperature. The aim of the modeling undertaken in this work is to establish the combustion dynamics, degree of pre-heating required and the geometry essential to the design of combustion based VAM mitigation multi-generation systems.

Aug 1, 2013

By E. Goris Cervantes

"A theoretical framework based on a detailed analysis of mine operations data from an oil sands mine in northern Alberta and the static simulation of truck cycle times are developed, verified, and validated in this paper. Implementation of this framework provides better results than existing tools that rely solely on manufacturer data. This, therefore, aids in efficient equipment planning for the life of the mine. The use of this framework to modify existing productivity curve estimation methods currently in use at the mine site is also proposed. This method replaces “loaded flat haul” with “loaded effective flat haul” in the productivity estimation. Validation of the model results in a 4% overestimation of productivity, versus an underestimation of more than 10% when using the existing in-house method. ¦ KEYWORDS Equipment planning, Life-of-mine (LOM) planning, Oil sands, Productivity, Truck cycle times RÉSUMÉ Un cadre théorique fondé sur une analyse détaillée des données relatives aux activités minières d’une exploitation de sables bitumineux dans le nord de l’Alberta et la simulation statique des temps de cycle des camions sont développés, vérifiés et validés dans cet article. La mise en oeuvre de ce cadre offre de meilleurs résultats que ce que proposent les outils existants, lesquels se basent uniquement sur des données des constructeurs. Ceci contribue donc à une planification efficace de l’équipement pour des projets relatifs à la durée de vie de la mine. On propose également de se servir de ce cadre pour modifier les méthodes d’estimation de la courbe de productivité actuellement utilisées sur le site minier. Cette méthode remplace le concept de loaded flat haul (la distance parcourue par des camions avec un chargement du point de collecte jusqu’au point de déchargement des résidus miniers) par celui d’effective loaded flat haul (la distance relative parcourue par des camions avec un chargement du point de collecte jusqu’au point de déchargement des résidus miniers) dans l’estimation de la production. La validation du modèle résulte en une surestimation de 4 % de la productivité, par rapport à une sous-estimation de plus de 10 % avec la méthode actuellement utilisée en interne. ¦ MOTS CLÉS planification de la durée de vie de la mine, planification de l’équipement, productivité, sables bitumineux, temps de cycle d’un camionINTRODUCTION One aspect that differentiates oil sands mines in northern Alberta from conventional hard-rock mining is the environment in which they operate. Due to ground characteristics, producers in the region experience roads with very high rolling resistance (RR) that, in turn, negatively affect haul-truck performance and greatly increase fuel consumption and emissions. Oil sands mining companies use some of the largest haul trucks in the world. In addition, oil sands mines cover more extensive areas than hard-rock pits, resulting in longer haul distances on roads made of comparatively more viscous material."

Jan 1, 2019

By D. Randolph Berry

Foster-Miller Associates has developed a set of guidelines to permit hoist manufacturers, mine owners, and MESA mine inspectors to design, purchase, install or inspect a safe and effective Emergency Escape Hoist, as required by the Coal Mine Health and Safety act of 1969. A series of surveys were carried out to determine: 1. The attitudes and local needs of the MESA District Managers. 2. Current escape hoist installations. 3. Equipment available for future designs. 4. Foreign methods and equipment for mine rescue. From these survey studies, preliminary guideline objectives were developed.

Jan 1, 2012

By Jayne Somers

Methane (CH4) is a potent greenhouse gas, accounting for 15 percent of all global greenhouse gas emissions in 2005. Since methane has a much shorter atmospheric lifetime than carbon dioxide (CO2), reducing methane emissions can achieve considerable climate benefits over the next 25 years. Coal seams often contain significant quantities of methane and CH4 released to the atmosphere from gassy mines during coal extraction is a major source of greenhouse gas emissions. Methane (CH4) emissions from coal mining activities constitute approximately 6% of total global human-related methane emissions. Coal mines around the world have recognized that methane is a clean energy resource that can be captured and used productively. Coal mine methane (CMM) is currently utilized for power generation, natural gas pipeline injection, vehicle fuel, industrial process feed stocks, on-site mine boilers, mine heating, and home heating distribution systems. Upgrading mine degasification systems can often improve gas quality and create favorable project economics. The United States has been a leader in coal mine methane (CMM) recovery and use since the 1990?s. There are now 15 projects at active underground mines in the U.S., as well as 26 abandoned mine methane projects. Recovery and use projects at active underground U.S. mines reduced methane emissions by approximately 49 Billion cubic feet in 2010. In an exciting new development, a ventilation air methane (VAM) mitigation project at the CONSOL McElroy mine in West Virginia was installed by Verdeo. Operational since September 2012, this is the first commercial-scale VAM project in the U.S. and the project will reduce methane emissions by an estimated 920 MMCF/yr. As part of the U.S. Greenhouse Gas Reporting Program, actual data on methane emissions from underground coal mines was collected for the first time in 2011 and reported to U.S. EPA in September 2012. The data collected will help inform stakeholders, particularly the underground coal mining industry, of CMM emission sources on public and private lands. The detailed data will also shed light on the specific sources of methane from active underground coal mines and highlight project opportunities for the U.S. coal industry. The paper will cover U.S. coal mine methane emissions, U.S. CMM utilization and destruction projects, Federal policies and State incentives for CMM capture and utilization. 2011 CMM data from the U.S. Greenhouse Gas Reporting Program Subpart FF will be analyzed and compared with previous U.S. Greenhouse Gas Inventory estimates. Other developments, including the voluntary carbon market, will be discussed.

Aug 1, 2013

By V M. Silva, P A. A Martins, V O. Matthew, A L. S Fonseca, E B. Cunha, A J. D Ferrari, E M. S Silva, A C. Silva, D R. T Vilela

The Anglo American phosphate mine is located in the Brazilian state of Goiás and possesses one of Brazil’s most important phosphate rock deposits, with the site being the country’s second largest producer of phosphate rock concentrate. Despite the site having been in operation since 1979, the mining team only started using explosives in 2004 when rocks with greater hardness started to appear in the mine’s geological profile. Rock excavation was previously performed mechanically. Until 2013, only rocks with high hardness were blasted, this following the standard drilling grid that was defined in 2004 without any changes in the blast parameters. The aim of this paper is to show how fragmentation optimisation has yielded positive results at all stages of the production chain, from the mine to the mill passing through an impact hammer crusher, a rod mill and ball mill, operating in close circuit with hydrocyclones.While incorporating the mine to mill holistic approach during the operational integration, the focus was on defining the blasting domains and respective optimal fragmentation and measuring the benefits of blasting in terms of reduction in energy and grinding media consumed in the comminution processes. In the first stage, the blasting team made changes to the blasting parameters and assessed the effects of these changes on fragmentation using computer software and on-site measurements. This generated a database that made it possible to divide the mine into blasting domains. For the second stage, teams from the plant, geology, mine planning and operation departments jointly made comparisons between the performance when processing stockpiles, which only included high hardness blasted ore (20–30 per cent of blasted ore). Changing the drilling grid’s size from 3.0 m × 3.8 m to 2.0 m × 2.6 m for high hardness rock with the presence of silicates resulted in a 40 per cent reduction in the P80 for the blasted material (from 459 to 278 mm), while changing the grid from 3.0 m × 3.8 m to 2.6 m × 3.2 m for high hardness rock without the presence of silicates generated a reduction of 25 per cent (from 270 to 204 mm). There were gains observed from the measurements at the mineral processing plant in terms of specific energy spent on comminution and on the consumption of grinding bodies in the rod mill. There was a measured reduction of circulating load during secondary grinding and a reduction in slime generation.CITATION:Silva, A C, Martins, P A A, Silva, E M S, Fonseca, A L S, Ferrari, A J D, Cunha, E B, Silva, V M, Matthew, V O and Vilela, D R T, 2015. Fragmentation optimisation – adopting mine to mill for reducing costs and increasing productivity, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 363–368 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Michelia Alba, Ronaldo S. Sampaio, Davi S. Braga, Mathieu Dubé

Climate change is pressuring industries and governments for decarbonization commitments, research, testing, and use of best practices to achieve the target of global warming below 1.5/2 °C. As it accounts for as much as 7% of all global CO2 emissions and 7% of energy consumption, the steel sector needs to address this issue with extended efforts. This paper provides information on the key potential of renewable biochar as an alternative fuel for pellet production. It also summarizes the successful application of biochar in a pioneering case study as the main fuel for a Grate-kiln pellet plant in Brazil, as well as the study of its use to replace coke and anthracite as an additive for iron ore pellets and other possible applications in the steel industry in COREM's precompetitive research & innovation program. The final discussion reveals the large quantity of biochar required by the Brazilian and Quebec scenarios for reducing CO2 emissions of iron ore pelletizing plants.

Jan 1, 2023

By D. J. Dollhopf

An overburden handling dragline operation was conducted at a strip mine near Colstrip, Montana. The objective of the demonstration was to determine the degree a dragline could mix overburden inhibitory zones during the spoiling process. In order to quantify the mixing process the overburden was: 1) scatter spoiled; 2) dump spoiled; and 3) spoiled in a normal manner. This demonstration was part of an effort to investigate means of reestablishing non-polluted hydrological systems in areas where surface mining directly impacts shallow ground-water resources. When inhibitory material constituted < 5% of the total overburden volume, such material was essentially not detectable in the resultant spoil pile. When inhibitory material exceeded 15% of the overburden volume it was always found in the resultant spoil pile, generally with a smaller extent, indicating partial dilution. Inhibitory overburden zones often reappeared at the base or top of spoil piles in the potential aquifer and root zones suggesting the need for selective placement procedures. Scatter spoiling did not appear to be significantly more effective than normal spoiling, however clump spoiling seemed to produce less mixing of inimical zones. Mining activity has reduced ground-water levels within 1600 m of the active pit. The aquifer which is developing in spoils appears to have similar confinement characteristics as those that existed in the premined aquifer. To date no definite trends have been observed concerning changes in surface or ground-water chemistry associated with mining.

Jan 1, 1978

By D Crequer

Land rehabilitation at Golden Cross is reviewed, 8 years after mine closure in 1997/98, from the perspectives of a Peer Reviewer (land rehabilitation) and a Regional Council Officer (Resource Consents compliance). Land rehabilitation items we discuss include: management of restored pastures, native plantings (on-site riparian and block plantings and off-site environmental riparian enhancement plantings), wetlands (on-site tailings lake and sediment ponds littoral zone plantings, and basement of the open pit; and off-site wetlands enhancement plantings), pine plantations on-site and on surrounding land, stabilization of the Tailings Lake Embankment (landslide) and Open Pit capping, capping of acid-mine-rock, stability of discharge channels, buildings and amenities, public access for recreation, educational uses, and future management of the site. Pest control has helped to conserve the rare and endangered HochstetterÆs (Leiopelma hochstetteri) and ArcheyÆs (L. archeyi) frogs, and a regionally significant stand of rare swamp maire (Syzygium maire) has been conserved and fenced.

Jan 1, 2006

By B. R. Mohal, S. Chander

"A new technique to determine wettability of powders is presented in this paper. In this technique the times for immersion of individual particles from air into liquids, defined as imbibition times, are measured. Through the measurements of imbibition times for a large number of particles, it is possible to determine homogeneity/heterogeneity of a powder sample with regard to its wetting behavior. Quartz particles give a very narrow distribution of imbibition times showing a homogeneous wetting surface whereas coal particles give a broad distribution indicative of the heterogeneous nature of its surface. The imbibition time measurement technique is considered to have certain advantages over other methods to determine wettability of powders in surfactant solutions. In this study we have also compared the imbibition times with the wetting rate mea¬surements obtained by a modified Walker test.INTRODUCTIONSeveral methods are available for determining wetting characteristics of sol¬ids. Each of the methods has been used in the past to obtain very valuable information for comparing wetting behavior of various solids in a given liquid or for comparing the wetting behavior of several liquids for a given solid. Each method measures a somewhat different aspect of wetting and therefore quantitative correlations between techniques have been difficult. A general approach is to use a method in which close similarity between the technique and the application (where results of wetting measurements are to be used) can be maintained. The objective of this investigation was to develop a method which could be used to determine the wetting characteristics of single particles in surfactant solutions. Wetting of individual particles is of importance in cap¬ture of dust particles by sprays of surfactant solutions.METHODS FOR DETERMINING WETTING — A BRIEF REVIEWThe various methods available for measuring wetting characteristics of solids include: contact angle, immersion/sink time, bubble pick-up, induction time, capillary rise, and displacement method measurements. Some of the methods are briefly reviewed in the paragraphs that follow."

Mar 1, 1989

By F. A. Rutledge

[An a part of the United States Department of the interior program for the development and use of Alaska raw materials, the Bureau of Mines is conducting an investigation of deposits of nonmetallic minerals accessible to the Alaska Railroad for use in building; materials is In the Alaska Railroad-belt area. The results of the investigations, to date, indices that raw materials for the preduction of brick products are in plentiful supply as cloy in the Anchorage area, as fire clay at Sheep Mountain, and as shale in the Healy Creek coal formations near Healy, Alaska.]

Jan 1, 1953

By Klaus L. Cappel

In 1972, the Bureau of Mines of the U. S. Department of the Interior commissioned the development and design of a Simulator for research and testing of mine roof supports used in long-wall mining. The purpose of the Simulator is to reproduce forces and displacements of a section of a mine roof in contact with one or more supports. This report is an account of the design process that resulted in the final configuration of the Simulator presented here. It includes discussions of engineering considerations that led to major changes in important details of the Simulator. These changes, however, did not substantially alter the basic design originally proposed, except for the elimination of certain originally-specified features that were adjudged as insufficiently cost-effective by both the Bureau of Mines and the design agent at an intermediate stage of the design.

Jan 1, 1974

This Bureau of Mines report and its companion report (Information Circular 9142) have been prepared to assist in the preparation of prefeasibility type estimates for capital and operating costs of beneficiation of various types of mineral occurrences using current technology. The handbook provides a convenient costing procedure based on the summation of the costs for the unit processes required in any particular mining or mineral processing operation. The costing handbook consists of a series of costing sections, each corresponding to a specific mineral processing unit process. Contained within each section is the methodology to estimate either the capital or operating cost for that unit process. The unit process sections may be used to generate, in January 1984 dollars, costs through the use of either costing curves or formulae representing the prevailing technology. The mineral processing handbook includes individual cost estimation sections for unit operations associated with comminution, beneficiation, solid-liquid separation, hydrometallurgy, and special applications as well as infrastructure and plant general and administrative costs. When using this system for estimating cost data for a mineral processing facility or for checking or verifying processing costs from an existing facility, a minimum amount of background information is necessary.

Jan 1, 1987

By W. N. Hoskins

This report covers the final results of a two-phase contract study conducted between July 1974 and October 1976. A comprehensive summary of the initial phase of the study is included. Phase I of the study involved the investigation and evaluation of all potential candidate underground systems for mining the deeper deposits of oil shale and associated minerals in the Piceance Creek basin of northwestern Colorado. Phase II called for the refinement and the detailed technical and economic analysis of the most promising system or systems, thus disclosed. Of the several systems initially investigated and evaluated, four Showed considerable merit for exploiting the deeper deposits: (1) chamber and pillar mining with spent shale backfill, (2) sublevel stoping with spent shale backfill, (3) sublevel stoping with full subsidence, and (4) block caving mining using LHD&apos;s. Final refinement and analysis of these four systems indicated their technical feasibility over at least part of the range of conditions expected in the deeper deposits. Their economic feasibility also was indicated under certain operating and market conditions. A variety of engineering, production, and cost information is provided on each of these systems.

Jan 1, 1976

By A. Yazadni-Chamzini

Considering the nature of open pit mines, harvest volume, it usually is required to remove a lot of waste to access to mineral planned grade. So, one of the most important part of open pit mines design, is waste dump site selection. Many factors are effective in waste dump site selection. These factors are sometimes in conflict with each other. So selecting the desired location for waste dump is a process complex and multi-criteria decision making. There are a variety of methods for decision making under complicated condition, such as fuzzy, Delphi, multi-criteria decision making and Expert system methods can be hinted. VIKOR method, which is one of the decision making multi criteria methods, is useful tool for decision-making. On the other hand with regard to uncertainty in decision-making, fuzzy approach is a useful tool for this purpose. This article has tried to select the best waste dump site in Sari Gunay Gold Mine by Fuzzy VIKOR. The results show that C position has a higher priority than other positions.

Jan 1, 2012

By Gaston Gendreau, Marcel Allard

"Sidbec-Normines Inc. est une société formée de trios partenaires soient: Sidbec, British Steel Corporation et la Compagnie Minière Quebec Cartier. L&apos;objectif de l&apos;opération minière est d&apos;exploiter à ciel ouvert le gisement d&apos;hématite spéculaire de Fire Lake et de produire au concentrateur de Lac-Jeannine, près de la ville de Gagnon, 6 million de tonnes de concentré pour alimenter l&apos;usine de bouletage de Port Cartier.Le présent exposé a pour but de fa ire ressortier les caractéristiques d&apos;une opération dont la mine est située à plus de 100 km du concentrateur, d&apos;en faire ressortir les particularités touchant le transport du personnel et du minerai. En plus, on traitera de l&apos;importance dans une telle situation d&apos;une organisation efficace dans la gestion des services et de l&apos;opération (atelier, concasseur, entrepôt, etc.).IntroductionSidbec-Normines Inc . a entrepris l&apos;exploitation minière du gisement de Fire Lake, le 1er janvier 1977. Le but de l&apos;entreprise est de produire annuellement six millions (6 000 000) de tonnes de concentré d&apos;hématite (oxide de fer) titrant 66% Fe au concentrateur de Lac-Jeannine a partir d&apos;un minerai d&apos;une teneur moyenne de 33% Fe, extrait de la mine de Fire Lake. Ce concentré est ensuite achemine à Port-Cartier et alimente I&apos;usine de bouletage.Les installations minières de Sidbec-Normines sont situées a trois endroits différents : la mine à Fire Lake, le concentrateur à Lac-Jeannine et l&apos;usine de bouletage à Port-Cartier. La mine de Fire Lake se situe à 83 km de la ville de Gagnon et à 100 km du concentrateur de Lac-Jeannine. Une route provinciale relie la ville à la mine et au concentrateur. Le minerai est acheminé de la mine au concentrateur par chemin de fer et le concentré est transporté par train sur une distance de 309 km à l&apos;usine de bouletage de Port-Cartier."

Jan 1, 1982

By J Webster-Brown

The Tui Mine is an abandoned Pb-Zn mine giving rise to water quality problems in the Te Aroha region of Coromandel, New Zealand. When sampled in September 2002, for example, both the Tui and Tunakohoia Streams draining the mine site exceeded ANZECC (2000) water quality guidelines for aquatic life protection (Cu, Cd and Zn) and recreational quality (Cd). Based on trace metal mass flux (kg/yr) from parts of the mine site, the principal pathways by which Cu, Zn and Cd contamination reach these streams have been identified as:the tailings dam leachate,the diverted stream water from above the dam,the drainage from Adit 5 (which accounts for 95 % of Zn and Cd contamination in Tunakohoia Stream), andto a lesser extent, run-off from waste rock piles below Adit 4 level. Of the various remediation options, which have been proposed for the site, the following are identified as providing the best protection for the Tui and Tunakohoia streams:stabilising the tailings dam embankment and capping the embankment and tailings,constructing and/or cleaning out engineered diversion drains around the perimeter of the tailings dam to divert surface water away from the tailings dam, andinstalling bulkheads within Adit 5. A formal postal survey of the people of Te Aroha (66 respondents from 230 surveys) indicated that their priority was that the site be made safe for the public to visit, and used for recreation. As soil samples in potential recreational areas of the mine site, significantly exceeded guideline values for Cu, Pb, Zn, Cd and As, soil removal or capping clearly also needs to be part of a remediation plan. Development of the site as a historical/ecotourism area was viewed favourably, as this may encourage more visitors to the Te Aroha area as well as educate local residents.

Jan 1, 2003

Q: It is May 1961 at Bill Wrather&apos;s Washington house. Bill, think back to your first job after college. Wrather: Perhaps I ought to go back a little bit further than my first job. I entered the University of Chicago with the idea of studying law. My intention was to take a 4-yr liberal arts course and superimpose a law degree on that. But during my undergraduate work I fell under the influence of R. D. Salsbury. He decided I had some talent as a geologist and influenced me to take a geological course. Nevertheless, I did not give up the idea of law. While in school I took a spell of typhoid fever and almost died. The doctor recommended outdoor exercise, so a geological job seemed logical. W. H. Emmons was a graduate student in the University and he interceded with Dr. Hayes of the USGS. I went on the payroll as assistant packer at $60 a month. I had one of the most glorious summers I ever spent in my life. That fall and the following year I took law courses and became thoroughly convinced that I was cut out for a geologist rather than a lawyer. I finished up my law work in 1908 while waiting for a job with Bill Emmons, who was doing a careful study of Goldfield and Tonopah.

Jan 4, 1964

By M. W. Grabinsky, B. D. Thompson

ABSTRACT: Use of cemented paste backfill (CPB) offers economic and environmental advantages over other backfill methods. However, many operations have limited knowledge of how their CPB behaves in situ. Therefore, to avoid over-pressuring containment barricades, backfilling strategies necessarily tend to be conservative. In situ monitoring at Barrick Gold Corporation’s Williams Mine and Inmet Mining Corporation’s Cayeli Mine has been conducted and factors controlling barricade pressures are demonstrated, including rise rates, binder content, stope geometry, and tailings properties. The application of barricade pressure monitoring on a stope-by-stope basis can increase backfilling efficiency and, thus, reduce stope cycle times, while maintaining optimal safety.

Jan 1, 2011

By Patrick J. Hannigan

The pile foundation designer typically performs a subsurface exploration program and static pile capacity calculations before selecting a pile foundation type, length, and capacity. During construction, a pile installation criterion must be established to meet these design requirements. This installation criterion usually consists of a minimum penetration resistance or blow count to confirm pile capacity and may also include a minimum embedment requirement. This text will focus on use of wave equation analysis and dynamic measurements to meet design requirements. BEFORE THE WAVE EQUATION Since the mid-1800s, over 450 dynamic formulas for pile driving control have proliferated. In their simplest form, these formulas relate hammer energy to the work of soil resistance, or simply: W ? h = R ? s (1) Where W = ram weight h = ram drop height or stroke R = pile capacity s = pile penetration per blow

Jan 1, 1990