Search Documents

The structure of the Bulli coal seam at Appin Colliery was detailed by the seismic reflection method. This unusual application of the seismic method was possible because there is a reflector near the seam as was revealed during exploration for petroleum in an area north-west of Appin. The reflector, which was at a depth of 1,500 ft, was shallow by normal reflection survey standards. Measurement of the seismic velocity at two ventilation shafts showed that the reflector was probably the Bulli coal seam. Accurate depth control was established from previous drilling results.INTRODUCTIONAppin Colliery, situated on the Southern Coalfield of N.S.W. (Fig. 1), is being developed to supply coking coal to the Port Kembla steelworks of Australian Iron and Steel Pty. Ltd. The colliery is mechanized and a detailed knowledge of structure, particularly faulting, is important in planning the workings.The Bulli seam, which is approximately 9 ft thick, and between 1,500 ft and 1,800 ft below the surface, is worked in the colliery. It is the uppermost member of the Permian Coal Measures and is overlain by Triassic rocks, which consist of thick sandstone beds containing beds of coloured shales, and which are subdivided into the Narrabeen Group, the Hawkesbury Sandstone, and the Wianamatta Group.In the early stages of development of the colliery, surface geological mapping and diamond drilling provided information on structure. Generalized results of the mapping are shown on Fig. 2. Drilling indicated that the physical and chemical properties of the Bulli seam are relatively constant, and that the seam is nearly horizontal, the average dipbeing about 1 in 25 to the west.

Jan 1, 1965

By J. Cayouette

In 1995, Louvicourt mine started one of the first paste backfill operations in Canada. From 500 000 t in 1995, the annual paste backfill tonnage produced reached 800 000 t in 1999. The maximum throughput of the surface plant (including binders) is 3500 tpd with a final density of 75% to 76% solids which gives a slump of 15 cm to 17 cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders in a mixture of 20% cement to 80% ferrous slag. In certain stopes, the binder ratio may vary from 2% to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5 Mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.

Jan 1, 2003

By Leping Liu, Li‑Ting Chen, Sachin Urade, Pengbo Chu

Mining industry requires constant adaptation to its practices in response to the dynamic change of the societal demand. Little information exists regarding how the US metal mining engineering education is prepared to meet with its industry needs due to the increase in critical minerals driven by the green energy transitions. This study aims to provide industrial perspectives on the current US metal mining engineering education and areas for improvement. An online survey with both closed- and open-ended questions were designed to seek opinions from the US mining industry. Findings indicated a shortage of qualified graduates from the current US metal mining engineering education system. The qualifications need to be improved include engineering sciences underlying mining methods, mining design experience, mining feasibility study, the connection between theory and practice, and understanding of the overall mining operation. The survey also identified future desired qualifications. The most desired ones in the next 5 years include an ability to acquire and apply new knowledge as needed and sufficient experience in the field. Respondents, regardless of the nature of their affiliated mining companies, unanimously recommended that collaborations between the industry and academia should be enhanced. The analysis of the results concluded four recommendations: (1) involve more multiple stakeholders in reforming mining education programs, (2) reinforce field experiences as a key part of mining engineering education programs, (3) enhance a closer collaboration between academia and industry, and (4) integrate emerging technologies (e.g., artificial intelligence/virtual reality) guided by pedagogical theories into new mining engineering curriculums.

Jun 26, 2023

By S. Hoskins, S. Chiovelli

"The annual budget for the repair and maintenance of equipment at Syncrude Canada Ltd. is in excess of $450 million. Of this amount, a significant portion can be attributed to the loss of material on various pieces of equipment throughout the operation. In order to effectively battle the different wear and corrosion mechanisms that lead to material loss, it is important to understand how materials behave in the environments in which they are used. Through the work carried out at Syncrude, and work conducted with various external collaborators, significant improvements in both equipment reliability and productivity have been achieved. This paper will review some recent field trials where materials research has demonstrated the potential for significant improvements in equipment run life and reduced maintenance costs. These field trials will demonstrate the need for understanding the interaction between various damage mechanisms and the materials used in different services. The paper will also discuss current areas of focus along with future directions for further work. IntroductionSyncrude Canada Ltd, located in northern Alberta, Canada, operates a mining, extraction, and upgrading facility that removes bitumen from oil sand to produce synthetic crude oil. Oil sand is mined from the orebody using conventional open pit mining techniques. Recently, the mining scheme has changed from a dragline/bucketwheel/conveyor system to a shovel/truck/crusher/hydrotransport operation as depicted in Figure 1. Since the start of production in 1978, the identification, development and application of wear protection has been an ongoing challenge due to the abrasive nature of the oil sands and the massive volumes of materials that are moved. The use of various materials and application processes along with component design modifications has resulted in significant improvements in both productivity and reliability (Adamic et al., 1995; Llewellyn, 1996, 1997; Anderson et al., 1998; Chiovelli et al., 1998).In an effort to continuously improve the operation, Syncrude has been quick to adopt new wear technologies. As seen in Figure 2, since the start of operation, a variety of materials have been used to increase wear performance and ultimately equipment reliability and availability. Although Figure 2 does not show a time axis, the bottom axis may also be used to represent a time progression for the predominate use of these materials at Syncrude. Tungsten carbide metal matrix composite (WC-MMC) overlays are currently the materials of choice for most of Syncrude’s critical production applications. Metal matrix composite overlay technology has potential for significant improvements and Syncrude is actively working with powder consumable manufacturers to advance this technology."

Jan 1, 2004

By Richard L. Rains

The Bureau of Mines made a study of mines and prospects of the Benton Range RARE II area (No. 5056), Mono County, California in October and November 1980. The study area is west of Owens Valley and 30 mi (40 km) north of Bishop, California. The mineral deposits were evaluated by examination of mines, prospects, and mining claims by the Bureau of Mines. Geological, geochemical, and geophysical studies were conducted by the Geological Survey. The principal mineral commodities of the Benton Range RARE II area are gold and silver but tungsten deposits may also extend into the area. Properties with resources are listed in table 1; their locations are shown on figure 1.

Jan 1, 1982

Filtration of pulps of varying densities is an essential operation in the hydro-metallurgical production of zinc. The use of filters naturally applies only to the "wet" plants, and in these varying types and sizes are in commission. At Risdon, the Moore suction filter is used for the heavier pulps, except in one instance, where a modification of the Butters-Cassell filter is installed.Filter presses are in general use, and of these, one is a washing unit; the plates, and frames are of cast iron or mild steel, except in one case which is a centre feed press having wooden frames.FILTER DESIGNThe problem of filtration presented itself very early in the history of Risdon and the first developments occurred in what was termed the 250 -lb. plant. Here experiments were made with many types of filters, and as this was the pilot plant on which the design of the 10 ton plant (10 tons of zinc per day) was based, quick decisions were necessary.An Oliver type filter was chosen for the heavier pulp or residue, and a Shriver wooden frame filter press for the lighter pulps.To this day, but with a number of variations, filter presses continue to function unopposed in their particular field; however, the Oliver filter was soon superseded because it was found impossible to wash the filter cake efficiently without repulping; consequently its use was abandoned and the Moore filter adopted.Both- these filters have been modified and developed in many ways to meet the requirements of a zinc plant, but they retain their original basic features.

Jan 1, 1949

By Edward J. Caldwell

In 1930 the Bureau of Mines published a description3/ f the concentrating process of the Magma Copper Co. as it had been developed to that time and was then employed. The prevent paper revises the description to the end of 1943 and includes a description of the smelting processes. Data from the mild and smelter operations for, 1942 are given in tables 1 to 14, Billing costs are included, but it is not permissible to publish smelter costs.

Jan 1, 1944

By Axel Preusse

Underground coal mining can cause seismic events. There is currently no way to predict such phenomena reliably, in particular stronger events. That is why, according to the current state of the art, empirical methods are employed in this field. Some assessment criteria, which relate to the geological and mining situation and either stimulate or rather help to avoid seismic events, are presented in this paper. These criteria are examined for a practical mining situation in Germany, with a view to estimate possible seismic events.

Jan 1, 2009

Editor’s note: As usual, the June issue features an industrial minerals review. And some thanks are in order. Thank you to the industrial minerals annual-review editor, to the technical committees chair and vice chairs and to the authors of the individual commodity profiles. Jim Norman of GeoTrans Inc. is the industrial minerals annual-review editor. Lucy McCartan, US Geological Survey, was the chair of the SME industrial minerals technical committees. She also served as the vice chair for agricultural minerals. Other technical committee vice chairs were: •Gary Tomaino, Specialty Minerals Inc., ceramics and refractory materials. •Srinivas (Vas) Veeramasuneni, US Gypsum, chemical raw materials. •William Langer, US Geological Survey, construction materials. •Vanessa Santos, Independent, fillers and pigments. •Richard Berg, Montana College of Mineral Science and Technology, specialty minerals. Their help makes possible this June industrial minerals issue. On behalf of the readers, the editors thank them.

Jan 1, 2002

By Sam X. Yao

The underwater concrete technology has historically evolved largely through a trial-and-error process of constructing marine works. Many outstanding examples exist of high quality concrete placed underwater. However, failures also occurred and led to excessive cost and/or schedule overruns. These failures were largely due to improper concrete mix design or improper placement. The problems may have occurred because proper underwater concrete construction techniques and experience have not been widely disseminated. This section focuses on technical issues of underwater concrete mix design, concrete production and placement, and quality control.

Jan 1, 2013

By Susanne Hering, Brent Kirby, Charles D. Litton, Tracy Allen, Kirk R. Smith, Rufus Edwards

In developing countries, high levels of particle pollution from the use of coal and biomass fuels for household cooking and heating are a major cause of ill health and premature mortality. The cost and complexity of existing monitoring equipment, combined with the need to sample many locations, make routine quantification of household particle pollution levels difficult. Recent advances in technology, however, have enabled the development of a small, portable, data-logging particle monitor modified from commercial smoke alarm technology that can meet the needs of surveys in the developing world at reasonable cost. Laboratory comparisons of a prototype particle monitor developed at the University of California at Berkeley (UCB) with gravimetric filters, a tapered element oscillating microbalance, and a TSI DustTrak to quantify the UCB particle monitor response as a function of both concentration and particle size and to examine sensor response in relation to changes in temperature, relative humidity, and elevation are presented here. UCB particle monitors showed good linearity in response to different concentrations of laboratory-generated oleic acid aerosols with a coarse (mass median diameter, 2.1 µm) and fine (mass median diameter, 0.27-0.42 µm) size distributions (average r2 = 0.997 ± 0.005). The photoelectric and ionization chamber showed a wide range of responses based on particle size and, thus, require calibration with the aerosol of interest. The ionization chamber was five times more sensitive to fine rather than coarse particles, whereas the photoelectric chamber was five times more sensitive to coarse than fine. The ratio of the response between the two sensors has the potential for mass calibration of individual data points based on estimated parameters of the size distribution. The results demonstrate the significant potential of this monitor, which will facilitate the evaluation of interventions (improved fuels, stoves, and ventilation) on indoor air pollution levels and research on the impacts of indoor particle levels on health in developing countries.

By P. Share

As part of JAGUARS (JApanese-German Underground Acoustic emission Research in South Africa), high-resolution tiltmeters were installed during 2007 at Mponeng gold mine, South Africa, in an attempt to study and understand the risks posed by in-mine seismic events and to subsequently use the knowledge gained to mitigate these risks. In December 2007, an M2.2 event occurred at Mponeng and was detected by the tiltmeters installed. The tilt expected for the M2.2 event is modelled through the use of numerical and analytical tools and utilizing, as input parameters, characteristics of the event such as the rupture area, the amount of slip, elastic properties of the rock, the state of stress before the event occurred, and frictional parameters of the rupture. The calculated tilt values are correlated and compared with the recorded data, and are found to be of the same order. Certain input parameters, such as the initial rupture point, are further constrained by varying them, during modelling, until the calculated and observed tilt values are approximately equal. From modelling, it can be concluded that the rupture point had to be closer to the location of the tiltmeters. In addition, possible locations acting as source areas for the observed aftertilt are determined. Further modelling still needs to be done to quantify the effects of the tunnel close to the tiltmeters and plastic deformation of the rock mass. Keywords high-resolution tilt data, Mponeng gold mine, M 2.2 seismic event, analytical modeling, numerical modeling, rupture plane.

Oct 1, 2013

By Mark S. Sanders

This report is a review and synthesis of the published literature dealing with personal equipment items used by low seam coal miners. This report reviews the following items of equipment: headgear, outer garments, respirators, cap lamp, gloves, knee pads, footwear, boots, helmets, ear protection, eye protection. Recommendations for further research and development are included.

Jan 1, 1978

By F. T. Wang, Y. Yuan, S. H. Tu, X. G. Zhang

Hydraulic support instability (HSI) is one of the most common causes of disasters in underground coal mining, posing a threat to the safety of mine workers and normal operation of the equipment. It is prone to occur in fully-mechanized mining faces with a large mining height (FMMLMH), especially when the dip angle of the coal seam is large. The key to controlling HSI is to deduce its mechanism and employ effective control techniques. This paper focuses on the analysis of HSI types, the key parameters and techniques to control HSI in FMMLMH, the establishment of a model of HSI in FMMLMH, and a multi-parameter sensitivity mechanical model of different HSI forms in the no. 7219 longwall face in Xutuan Coal Mine, Huaibei Mining Group, by using sensitivity analysis . The results show that HSI mainly presents in three forms: hydraulic support gliding (HSG), hydraulic support tilting (HST), and hydraulic support tail twisting (HSTT). The occurrence of the above three forms depends mainly on support anti-instability capability. In the no. 7219 longwall face, HSG and HST are the main two forms of HSI. The dip angle of the working face and the friction coefficient between floor and hydraulic support are the sensitive parameters for HSG, while HST is strongly dependent on the dip angle of the working face and the friction coefficient between roof and hydraulic support. By the applications of measures such as the oblique layout of the working face, cutting the floor into a step pattern, moving the support under pressure, and raising the setting load, the support stability was controlled effectively.

Jan 1, 2015

The income of the Institute is derived mainly from dues, advertising in MINING AND METALLURGY and sale of publications. These sources are fortunately supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for especial purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Rocky Mountain Fund and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowments of the Institute, it being felt that unusual opportunities exist for research and public and professional service through the organization.

Jan 1, 1939

By A J. Nick, I I. Townsend, J M. Schuler, J D. Smith, R P. Mueller, L Sibille, K Leucht, J J. Fox

The first steps for in situ resource utilisation (ISRU) on target bodies such as the Moon, Mars and near-Earth asteroids (NEA), and even comets, involve the same sequence of steps as in the terrestrial mining of resources. First exploration including prospecting must occur, and then the resource must be acquired through excavation methods if it is of value. Subsequently a load-haul-dump sequence of events occurs, followed by processing of the resource in an ISRU plant, to produce useful commodities.While these technologies and related supporting operations are mature in terrestrial applications, they will be different in space since the environment and indigenous materials are different than on Earth. In addition, the equipment must be highly automated, since for the majority of the production cycle time, there will be no humans present to assist or intervene. This space mining equipment must withstand a harsh environment which includes vacuum, radical temperature swing cycles, highly abrasive lofted dust, electrostatic effects, van der Waals forces effects, galactic cosmic radiation, solar particle events, high thermal gradients when spanning sunlight terminators, steep slopes into craters / lava tubes and cryogenic temperatures as low as 40 K in permanently shadowed regions. In addition the equipment must be tele-operated from Earth or a local base where the crew is sheltered. If the tele-operation occurs from Earth then significant communications latency effects mandate the use of autonomous control systems in the mining equipment. While this is an extremely challenging engineering design scenario, it is also an opportunity, since the technologies developed in this endeavour could be used in the next generations of terrestrial mining equipment, in order to mine deeper, safer, more economical and with a higher degree of flexibility. New space technologies could precipitate new mining solutions here on Earth.The NASA Kennedy Space Center (KSC) Swamp Works is an innovation environment and methodology, with associated laboratories that use lean development methods and creativity-enhancing processes to invent and develop new solutions for space exploration. This paper will discuss the Swamp Works approach to developing space mining and resource extraction systems and the vision of space development it serves. The ultimate goal of the Swamp Works is to expand human civilisation into the solar system via the use of local resources utilisation. By mining and using the local resources in situ, it is conceivable that one day the logistics supply train from Earth can be eliminated and Earth independence of a space-based community will be enabled.CITATION:Mueller, R P, Sibille, L, Leucht, K, Smith, J D, Townsend, I I, Nick, A J, Schuler, J M and Fox, J J, 2015. Swamp works – a new approach to develop space mining and resource extraction technologies at NASA’s Kennedy Space Center: prospecting, excavation, load, haul and dump for in situ resource utilisation, in Proceedings Third International Future Mining Conference, pp 297–304 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By Tellis D. A

An outline is given of the general position of earthsciences information in Australia, the background to development of the Australian Earth Sciences Information System (AESIS) and the role of the Australian Mineral Foundation in developing and co-ordinating the projeot in co-operation with the CSIRO, BMR, National Library of Australia, AGIA, and many companies.Details 'of the system, method and anticipated rate of input (especially of unpublished material at which the System particularly aims), mode of dissemination, and use of the data base are discussed. Information on theAustralian Thesaurus of Earth Sciences and Related Terms and brief details of some 30 earth sciences information collections in Australia is given.

Jan 1, 1977

By A. J. Kraemer

The properties of crude petroleum continue to interest the Bureau of Mines and constitute an important phase of its major studies on the mineral resources of the United States. The Bureau's interest in the subject has been intensified by frequent requests for information on the characteristics of crude petroleum from various producing fields. Since its inception the Bureau of Mines has collected and analyzed samples of typical oils and at present has surveyed and classified crude petroleums from nearly all the known oil fields of the Western Hemisphere. Results of these surveys have been presented in various Bureau of Mines publications. (See bibliography, appendix A, p. 145.) The nature and comparative value of crude oils from various countries and the extent to which these oils may be considered potential competitors for markets are of manifest importance to the petroleum industry in all lands, largely because all crude oils, wherever produced, are either actual or potential competitors for a market with all other crude oils. The numerous discussions of foreign production of oil that have appeared in the technical press in the past indicate the great interest of the United States in this subject.

Jan 1, 1937

The Autogenous Fine Grinding Kelsey Axial Displacement (KAD) Mill The marginal improvements which continue to be made to fine grinding practices have exposed the limits of conventional technologies and highlighted the need for a radically new approach. The patented autogenous Kelsey Axial Displacement (KAD) Mill design consists of a rotating spherical grinding chamber, which shares the same spherical centre as the shaft-mounted counter-rotating disc assembly. The axis of the disc assembly can be inclined to the axis of the spherical grinding chamber by pivoting the disc shaft about the common spherical centre. The inter-particle energy transfer required for breakage results from particle velocity differentials created by the discs intercepting the rotating mass. Particle size reduction is concentrated in high shear zones, which envelop the outer surface and periphery of the discs. This paper traces the development of the KAD Mill from pilot to commercial scale. Pilot work covers a range of minerals including magnetite, calcite, dolomite, barite, limestone and talc. Test results include open and closed circuit operation in wet and dry modes. Conventional milling constraints and energy consumption issues are addressed while new dimensions are added to the feed size range acceptable for wet and dry grinding to fine and ultra-fine sizes.

Sep 13, 2010

By Iván Calmell del Solar Salas

Desde el año 2014, se ejecutaron pruebas piloto en zonas en condición de cierre progresivo dentro de la Unidad Minera Constancia, propiedad de Hudbay Perú S.A.C. El objetivo de estas pruebas fue lograr cierres sostenibles en base a metodologías no convencionales y al uso de conocimiento ancestral local. Para la revegetación de estas áreas hemos sustituido la práctica común de siembra de pastos exóticos de rápido crecimiento, por el uso de recursos fitogenéticos nativos con el fin de proveer a las áreas intervenidas de una cobertura vegetal idónea con el propósito de que sea la base para la rehabilitación y mejora de la Biodiversidad

Sep 1, 2017