Search Documents

By Gray Mullins

This paper presents results from model and full-scale tests to assess the interface bond between a cast-in-place concrete seal slab and steel H-piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid was displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also tested. In the model tests, eight 15 cm deep, W6 x 15 sections were used for two different embedment depths of 1.5d and 2d, d being the depth of the section. In the full-scale tests, 16 specimens 35 cm deep (W14 x 90 sections) were tested with the embedment varied between 0.5d-2d. The results show that significant bond stresses developed even in the worst placement condition. Recommendations made for revising current values in specifications have already been implemented by the Florida Department of Transportation.

Jan 1, 2013

By N. Mphathiwa

When slope angles are designed during open pit optimization, there is a risk factor applied in steepening the slopes. The steepening of slope angles has implications for the safety and economics of the mining operation. The steeper the slope angles, the greater the probability of slope failure. Although a slope failure will result in added costs, the challenge is to compile an accurate cost-benefit exercise optimizing the economic benefits of the project without exposing mine workers and equipment to unacceptable risk of rockfalls. A balance between the safety of the operation and the economics of the investment is therefore required. The ideal situation is to have a slope monitoring system that will predict slope failure by detecting any ground movement before the actual failure occurs. This early warning will allow the risk factor to be applied with a high degree of confidence, knowing that the risk will be adequately mitigated. The objective of this paper is to provide guidelines on how to design an optimal survey slope monitoring system. It is the authors? view that for a survey monitoring system to yield desirable results, it should adhere to survey principles such as working from the whole to part and consistently cross-checking. The case study used is Jwaneng Mine, and the design strategy outlined can be used as a guideline for developing a new slope monitoring system or to optimize an existing one.

Jan 1, 2014

By Christopher Jon Preston

This paper describes a type of ammonium nitrate (AN) produced in a patented experimental atomization/aerodynamic process. This AN exhibits outstanding properties for use as a main ingredient to a new family of AN-based commercial explosives. Micro-particle ammonium nitrate (MP-AN) is produced by atomizing either an 83% or 85% AN solution which has been doped with a two component surfactant NSol 1000 (NSol). NSol imparts some water-resistance as well as provides a means of increasing density and bulk strength. Increased detonation velocities, well in the range of emulsion explosives, can be achieved. The maximum manufacturing temperature is less than 100°C. The methodology has the potential of being environmentally friendly since any effluent can be recycled back into a make-up tank to be re-used by the closed loop method. The process has a small footprint.

Jan 1, 2015

DESCRIPTION OF OREThe ore consists, in general, of a very finely grained mixture of sphalerite, galena, and pyrite, with a gangue of quartz and schistose material, and contains about one ounce of silver to the unit of lead.Minor minerals are chalcopyrite, tetrahedrite, and ruby silver. The amount of gangue within the ore-bodies themselves is usually less than 20% of the weight of the whole. The ore is banded in a way that corresponds to the structure of the original schists, and is by no means uniform in composition-at one point, for example, blende may predominate, and a few feet farther on the body may become highly pyritic.Owing to the intimate association of the mineral constituents of the ore, it is very difficult to separate them from one another.Although this remark applies to ore from all parts of the field, the difficulty is particularly noticeable with Rosebery ore, the minerals of which are more intimately mixed, and are of smaller grain size than are the minerals of the Hercules ore.To effect a reasonably clean separation, it is necessary to grind the ore so that 90% passes a 200-mesh I.M.M. screen. Microscopic examination of the crushed product shows that 85% of the minus 200-mesh material is less than 30 microns in diameter, or, in terms of screen sizing, is minus 400 mesh. Particles under 30 microns are found to consist, of one mineral only, but in particles over this size separation has not always been effected. For instance, it is known that part of the galena and of the pyrite in the zinc concentrate is associated with sphalerite, and that part of the galena in the mill residue is associated with pyrite. There is only slight association between the minerals in the lead concentrate.

Jan 1, 1927

By C N. Whata

While there is no specific obligation on the part of any applicant to consult directly with tangata whenua (people of the land), recent cases highlight the need to engage in active consultation in order to avoid serious objections and delay, particularly where a proposal may affect the matters referred to in section 6(e) (Waahi tapu/sacred places) and 7(a) (KaitiakitangaiGuardianship) of the RMA.   The Environment Court has shown some sympathy for tangata whenua where waahi tapu and other significant matters of cultural concern are at risk because of a proposed development. There are several practical steps that can be taken to minimise the potential for serious objection including: ò knowing who to contact and how to contact them; ò demonstrating empathy for the concerns of tangata whenua; ò engaging in proactive consultation, for example meeting at a time and a place that is suitable to tangata whenua, and a preparedness to meet the costs of tangata whenua etc; ò demonstrate an awareness of tangata whenua issues; being aware of the types of mechanisms that are available to remedy, avoid etc adverse effects on matters of concern to tangata whenua.

Jan 1, 1997

A slag-metal equilibrium study of the system SnO-FeO-(Si02+Al2O3)/Sn-Fe was carried out at 1250°C. The distribution coefficient, k =(Sn/Fe)metal X (Fe/Sn)slag was found to range from 246 for an iron contentof 0·53 per cenrt in the metal to 82 for an iron content of 6·4 per cent. The value of the ratio ?SnO/?FeO was calculated and found to be approximately a function of per cent SnO in slag alone in the region (Si02+Al2O3)/ FeO = 0·4 to 1·2. Comparison with other published work suggests that the addition of CaO to slags having (SiO2+Al203)/FeO ratios of about 1·1 raises the value of ?SnO/?FeO...

Jan 1, 1974

The limit of pressure to which an underground dam may with safety be subjected, is a question that-as far as the writer knows has not received the same attention from authorities on engineering construction, or practical mining, that has been accorded to questions on which the design and strength of other structures or machines in connection with a mine are based. That dams may, under certain conditions, be constructed to resist water under great pressure is a known fact. But the difficulty of demonstrating beforehand that any proposed structure of this kind will withstand the pressure and be effective is, owing to the indeterminate nature of some of the risks to be provided against, very great. In the present state of our knowledge it may almost be laid down as a rule, that a dam of this kind should not be undertaken where grave consequences would attend failure until experience of structures where the physical conditions are similar, but where there are no such risks, has given assurance that such work would stand.In Mines and Minerals for May, 1900, there is published a paper by Mr. James McNaughton describing the construction of three underground dams in the iron mining district of Michigan.The first of these was put in to hold back a flow of 750 gallons per minute, which when pent up created a pressure of 276 pounds per square inch, showing that the height of the sustained column was about 635 ·feet. The hole through which the water issued was in the bottom of the cross cut it was enlarged by removing all loose rock for a depth of 18 ft...

Jan 1, 1901

A commonplace, sometimes overlooked or taken for granted, article of everyday existence is the tin can. Produced from thin gauge low carbon steel, and commonly coated with a mere 60 millionths of an inch of pure tin, the product is however strong and corrosion resistant. Tin-plate serves a myriad of purposes-the most important being to meet the requirements of the canning industry. Australia's newest steel product, tin-plate, was first produced on a commercial scale during the early part of August, 1957. The commissioning of the Hot Dip Tinning Plant (Fig. 1) of The Broken Hill Proprietary Co. Ltd. at Port Kembla, marked the culmination of a proposal dating back to 1939, the advent of World War II having caused its deferment to the present time.Cornish tin is known to have been exported as early as 300 B.C. to Syria and tinned vessels existed even in the year A.D. 23. The tin coating of plate could be described as an ancient art, believed to have had its origin in Bohemia in the thirteenth century. During the next 450 years, the process spread through Saxony to Pontypool in Monmouthshire, but it was a further half century before any measure of success was obtained.Perhaps the two greatest milestones in tin-plate manufacture were the rolling of iron plates first carried out in 1728, thereby outmoding the hammer formed sheet, and more recently, the development of the electro-deposition process. By the nineteenth century, several important changes had arisen; namely, the substitution of steam for water power, coke for charcoal in the production of the base metal, and...

Jan 1, 1958

By F. T. Cawood, M. A. Jooste

This paper describes the survey monitoring processes at Venetia, which are discussed under visual inspections, ad hoc investigations, system monitoring and slope stability radar monitoring. This is followed by a description of the main survey monitoring methods. The next section briefly states typical problems, i.e. the atmospheric corrections required to adjust total station distances, maintenance of the system and management of the monitoring process. The paper ends with some important lessons that could be applied to similar monitoring programmes. These lessons are firstly, communication is most important, process a vital part of the system, a champion must take responsibility for the programme and system planning ensures that the monitoring results are needs driven.

Jan 1, 2006

By W. L. Falke

This Bureau of Mines report illustrates critical path planning and scheduling techniques as applied to typical mining operations. Detailed examples of arrow diagramming and computer oriented applications of critical path methods are given. Program Evaluation and Review Technique (PERT) is discussed briefly in comparison to the Critical Path Method (CPM).

Jan 1, 1966

In undertaking to write a few notes on practical mining in Bendigo, the great quartz mining centre of Victoria, which just now is celebrating its fiftieth anniversary of gold mining, satisfaction must be expressed which is, no doubt, shared by all mining men and inyestors, that Bendigo has not lagged behind other Australian mining districts in the evolution of mining from its crude state, subsequent to the discovery of gold in 185 to its present more perfect state; and though it may be said that it has not yet reached the high pinnacle of perfection towards which advanced science and change of conditions may yet lead it in the course of future progress, yet, what has already been done in this respect, the adoption of the most approved methods appliances and modern machinery, tending towards greater and still greater efficiency, facility, and economy in our mining industry, must be accepted as a guarantee that in tne future as well as in the past, progress in our means of developing our mining resources will ever remain our watchword, by means of which future difficulties will be overcome as well as they have been removed in the past.The adoption of this principal, combined with a study of rigid economy, has raised gold mining here, as well as in other places, from a state of speculation, and sometimes wild speculation, to the status of a solid, stable industry, the strong supportand backbone of the country in which it flourishes. Two of the principal factors which have been to a great extent instrumental in bringing about this satisfactory state, must be specially mentioned.

Jan 1, 1902

By W. P. Yant

[This report describes results of a study bf the carbon monoxide and particulate matter in the air of the Holland Tunnel and metropolitan New York made by the Bureau of Mines (which had participated in the development]

Jan 1, 1941

The Burra Burra Mine is situated in complexly folded Torrensian dolomites and limestones forming the faulted axial region of a major anticline. The orebody mined was largely of secondary origin and confined between two faults, Kingston's on the west and Tinline's on the east. The orebody occurred at the junction between cherty dolomites and a clastic limestone with a large mass of marble breccia along its western margin. Secondary ore consisted of carbonates and oxides in the breccia and the ore bed and detrital copper minerals deposited as part of a clastic breccia in sinkholes and solution cavities in the dolomites and ore beds.Primary sulphides occur disseminated in the marble breccia and in stratiform habit in the ore bed. Kingston's so-called "lode" may be mineralized marble breccia.The marble breccia appears to be of diapiric or sedimentary origin and there is evidence to support a sedimentary origin for some of the copper sulphides. No igneous rocks have been discovered within 20 miles of the mine and any hydrothermal activities were probably at comparatively low temperature. The possibility of extensive stratiform and disseminated copper sulphide mineralization in the marble breccia and ore bed requires testing by further drilling and geophysical surveys.INTRODUCTIONThe re-interpretation of Burra Burra geology and ore formation discussed in this paper resulted from a comprehensive investigation of the mine and its surrounding district begun in December 1961 and in progress at the time of writing. (February 1963). The decision to investigate Burra Burra was taken after a thorough examination of records and reports of all non-ferrous metal deposits throughout South Australia and was given impetus by a report by Thomson (1963) suggesting a sedimentary origin for the copper mineralization. Although the author does not concur fully with Thomson's interpretation there is no doubt that sedimentary processes have played an important part in the formation of the Burra Burra copper deposit, nor is there any doubt that igneous activity played no part.

Jan 1, 1963

By M. Kinne

Catalyst preparation/ characterization Slightly modified DP (~Schumacher et al. Catal. Lett. 89, 109, 2003) CeO2 HAS 15 from Rhodia calcined in air for~ 2h BET: ~188m2/g, particles size: 5.7nm (TEM, XRD) + HAuCl4 at pH of 6.5-7, (>95% of the Au was deposited) ? Au/CeO2 (2.6wt% Au, ICP-AES) A new conditioning procedure was applied, including heating at low temperature in N2 and H2/N2 mixtures) Patent DE 10205873A1. Very small Au particles <2nm, for CO oxidation catalyst as Au/TiO2, Au/Fe2O3, and Au/Co2O3 Here Au particles size <3.5nm (XRD) Summary ? CO is nearly exclusively adsorbed on the Au particles ? Positive reaction orders of 0.5 are found for CO and H2O ? Ea= 40kJ/mol ? The catalyst is very active and stable ? During WGS reaction huge amounts of formates are formed and cover the surface ? The activity of the catalyst seems to be correlated with the formate species.

Oct 1, 2003

By Jean Cayouette

"In 1995, Louvicourt Mine started one of the first paste backfill operations in Canada. From 500,000 tonnes in 1995, the annual paste backfill tonnage produced reached 800,000 tonnes in 1999. The maximum throughput of the surface plant (including binders) is 3,50Ot/d with a final density of 75 to 76% solids which gives a slump of 15 to 17cm. Following the start-up of the paste backfill plant, the backfill strength performance levels were well below the pilot plant’s predictions. The introduction of ferrous slag, laboratory tests on various binder ratios with or without additives, and the desliming of the tailings enabled us to optimize the mix and operation costs. Primary and secondary stopes are filled respectively with a paste containing 4.5% and 2% binders consisting of a mixture of 20% cement and 80% ferrous slag. In certain stopes, the binder ratio may vary from 2 to 7%, but always in a ratio of 80/20. Six years after start-up, or 4.5mt of paste backfill later, this paper discusses the present operation and the major changes that have occurred over the years to optimize both the operation and the paste fill quality.INTRODUCTIONLouvicourt Mine is operated by Aur Resources Inc. which owns 30% of the shares. Its partners are Novicourt Inc. (45%, subsidiary of Noranda Inc.) and Teck Corporation (25%). The mine is located in the north-west part of Quebec, about 600 km north of Montreal and about 25 km east of Val d’Or. The mine commenced commercial production in July 1994."

Jan 1, 2002

By John Gamble

This paper summarizes the weight of epidemiological evidence to evaluate the hypothesis that asbestos exposure is causally associated with increased risk of gastrointestinal (GI) cancers as suggested by Selikoff in an early study of insulation workers. This review looks at populations that develop GI cancers, namely stomach, colorectal, colon and rectal. Guidelines for assessing causality are strength of association, biological gradient and consistency of the associations. Exposure?response (E?R) was evaluated using three methods to estimate exposure. Rate Ratios (RRs) for lung cancer and percent of mesothelioma are used as surrogate measures of asbestos exposure for all the cohorts of exposed workers. Quantitative or semi-quantitative estimates of cumulative exposure to asbestos were also used to assess E?R trends and were compared to E?R trends for lung cancer and mesothelioma in individual studies. Surrogate measures are important since there are few individual studies that have assessed E?R. None of the various methods to estimate asbestos exposure yielded consistent E?R trends and the strength of the associations were consistently weak or non-existent for the four types of GI cancers. The epidemiological evidence detracts from the hypothesis that occupational asbestos exposure increases the risk of stomach, colorectal, colon, and rectal cancer. Findings are briefly summarized below. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestos; Colon cancer; Colorectal cancer; Gastrointestinal cancers; Ingestion; Lung cancer; Mesothelioma; Rectal cancer; Review; Stomach cancer

Jan 1, 2007

Raw materials account for over 60 per cent of the cost of hot metal production in classical blast furnaces and the principal cost component is cost of coke. Dependence on coke is a traditional weakness of blast furnace ironmaking and while efforts have been made to evolve alternative ironmaking technologies which do not use coke, such as direct reduction, smelting reduction, and the more recent method of making iron carbide, blast furnaces continue to be the most efficient means of producing bulk hot metal even today. Coal injection, to the extent of 150 - 200 kg/t of hot metal, has been one of the major innovations made in blast furnaces to decrease cost and to reduce the dependence on coke. This has, however, given rise to more stringent coke property requirements (which often means more expensive coke) - a `tail spin&apos; of Sorts!

Jan 1, 1999

By Hessam Yazdani

In comparison to the conventional piled foundations, the piled-raft foundations provide a more economical solution to support high-rise buildings constructed on soft soils. In this type of foundations, the bearing capacity of the underlying soil is taken into account to support the superstructure loads and the piles are placed to control both the total and differential settlements of the superstructure. Currently, there is not a standard and worldwide acceptable approach to select the location of the piles and most of piled-raft foundations are designed based on the experience of designers. Therefore, particular attention should be given to the optimal design of this type of foundations in order to minimize the considerable construction costs involved. This paper examines the capability of the ant colony optimization (ACO) algorithm to optimize the piled-raft foundations subjected to static and seismic loadings. The soil-pile interaction is considered by modeling the side and tip resistance components of the piles using the nonlinear Winkler-based p-y and t-z curves in the OpenSees program. The soil-raft interaction is taken into consideration using the Winkler springs beneath the raft. The objective of the optimization problem is to minimize the construction cost of the foundation by taking the configuration and number of the piles as design variables. The side and tip forces of the piles as well as the total and differential settlements of the foundation under the serviceability limit state are considered as the constraints for the optimization problem. Results show that in addition to the type of analysis (linear/nonlinear), the regard or disregard of the soil-pile interaction in the analysis can significantly change the optimal solution. The optimal solutions obtained match the engineering expectations and indicate the effectiveness and capability of the ACO algorithm to minimize the construction cost.

Jan 1, 2013

By B. K. Gorain

"As mining has evolved over a century, so are the challenges associated with mining. Mining of complex ore bodies at greater depths is a major challenge requiring high capital and operating costs due to remote locations, high energy costs, water quality and complex environmental issues. In addition, the stakeholder expectations are growing along with challenges associated with highly complex mine permitting processes and changing demographics of mining jurisdictions. The dynamic metals market adds to these challenges impacting the long term development and sustainability of mining projects.These challenges are compelling mining companies to look at various innovations with an integrated approach focusing on meeting the needs of various stakeholders. Mining companies are slowly tapping into some successful concepts that have transformed other industries such as manufacturing, chemical, pharmaceuticals along with oil and gas.This paper provides an overview of various innovations and technology developments in mineral processing that have shaped the current mining industry. A glimpse of the present and future challenges in mining is also presented. An integrated approach to problem solving involving various stakeholders is gaining momentum and this has been reflected in this paper. Various developments that are being pursed in mineral processing focusing on a change in the existing mining paradigm are also presented in this paper.INTRODUCTIONAs mining is evolving, so are the challenges associated with mining. Some of the key challenges are complex ore bodies at greater depths, high capital and operating costs, water scarcity and quality issues, high energy costs, complex environmental issues including tailings management, worldwide constraints on resource availability, more and more elaborated regulations in emerging economies impacting the permitting processes, increasing stakeholder expectations, changing demographics of mining operations with ever-changing cultural or community expectations and the urgent need for a better assessment of project viability, this in very dynamic metals markets impacting the dynamics of mining projects development and sustainability."

Jan 1, 2016

By W. A. Calhoun

This report gives results of metallurgical investigations performed by the Bureau of Mines on mineral samples taken during April 1959, from Hawaiian bauxite deposits on the islands of Kauai, Maui, and Hawaii. The bauxite samples were tested at the Bureau&apos;s Rolla Metallurgy Research Center, Rolla, Mo., to determine if alumina could be extracted. The results were encouraging. Extraction of the alumina by the American Bayer type digest of crude ore samples from Kauai, Maui, and Hawaii recovered 78.8, 73.1, and 70.0 percent, of the total alumina, respectively. These recoveries were increased to 82.8, 85.5, and 79.5 percent by modifying the treatment, which consisted essentially of calcination and weak caustic desilication to provide a residue. The residue was then treated with calcium oxide and digested in a strong caustic solution to extract the alumina.

Jan 1, 1962