Search Documents

By T. G. Carter

Support system design for tunnels and underground excavations has for many years relied heavily on the use of rock mass classification systems and the Hoek-Brown failure criterion as a means for characterizing rock mass behaviour. Because of their development, both the GSI system and the Hoek-Brown criterion admirably characterize most ?normal? rockmasses from the viewpoint of their behaviour for rock excavations. They, however, run into difficulties when applied at the two ends of the rock competence scale. This is largely because block size and incipient strength are such that rockmass behaviour in these domains tends not to be controlled by interblock shear strength but rather by material strength. At the low end of the rock competence scale (UCSi <<15 MPa and GSI generally <30) discontinuities play less of a role and rock mass strength tends to matrix strength. Similarly, at the high end of the scale (GSI >>65, mi>>15), because discontinuities are now widely spaced, block size becomes so significant that again, intact material behaviour rather than the fracturing becomes the dominant factor controlling rock mass strength. In this paper several case examples are presented to illustrate the application of the high-end (spalling) and low-end (weak ground) transition Hoek-Brown relationships proposed by Carter, Diederichs and Carvalho (2007) as a basis for better defining rockmass behaviour at the extreme ends of the rock competence scale.

Jan 1, 2008

By H. A. Oliveira, A. Azevedo

Physical and chemical characterization and solid/liquid separation of turbid waters from a river affected by an iron tailing rupture disaster (Gualaxo do Norte River, Brazil) were studied at bench scale. Parameters such as turbidity, pH, surface tension, electrical conductivity, total suspended solids (TSS), particle size distribution (micro- and nanoparticles), and zeta potential were analyzed from samples collected at three different river depths. The results in all samples showed the presence of micro- and nanoparticles, ranging in diameters from 100 nm to 200 μm. Best results for flocculation and settling were obtained at pH 7.5, through an innovative combination of eco-friendly reagents: (i) ferric hydroxide precipitates (10 mg L−1 Fe3+) to sweep (enmesh) the dispersed solids and (ii) gelatinized starch (5 mg L−1 ) to form large flocs. The results showed removals between 90 and 100% of total suspended solids (micro- and nanoparticles), resulting in clear water with residual turbidity < 7 NTU. It is believed that this innovative alternative has a high potential for flocculating and treating the turbid water at Gualaxo do Norte River, assisting the water treatment stations.

By H. A. Oliveira, A. Azevedo

Physical and chemical characterization and solid/liquid separation of turbid waters from a river affected by an iron tailing rupture disaster (Gualaxo do Norte River, Brazil) were studied at bench scale. Parameters such as turbidity, pH, surface tension, electrical conductivity, total suspended solids (TSS), particle size distribution (micro- and nanoparticles), and zeta potential were analyzed from samples collected at three different river depths. The results in all samples showed the presence of micro- and nanoparticles, ranging in diameters from 100 nm to 200 μm. Best results for flocculation and settling were obtained at pH 7.5, through an innovative combination of eco-friendly reagents: (i) ferric hydroxide precipitates (10 mg L−1 Fe3+) to sweep (enmesh) the dispersed solids and (ii) gelatinized starch (5 mg L−1 ) to form large flocs. The results showed removals between 90 and 100% of total suspended solids (micro- and nanoparticles), resulting in clear water with residual turbidity < 7 NTU. It is believed that this innovative alternative has a high potential for flocculating and treating the turbid water at Gualaxo do Norte River, assisting the water treatment stations.

By Ray Wood, Rene Sterk, Robin Falconer, Sean Aldrich, Simon Nielsen

"The Chatham Rock Phosphorite project is situated 450 km east of New Zealand at approximately 350 to 450 m water depth. The deposit occurs as a thin layer of phosphatebearing glauconitic sand at the surface of the sea floor and has a thicknesses typically ranging from 0 to 1 m. The sand layer consists of mainly silt and sand-sized sediments, with phosphatised chalk nodules up to 15 cm in diameter. Phosphate nodules were first discovered on the Chatham Rise in the 1950s by a New Zealand Government survey. During the 1960s to 1980s several private and government sponsored cruises explored the Chatham Rise and surrounding seafloor area. A total of 1174 samples were collected over a 600 km2 area with the majority of the samples collected using a pneumatic -or large Van Veen-style grab-sampler.Since acquiring the licence in 2010, Chatham Rock Phosphate Limited has conducted six cruises in two programs in the Project area. A total of 261 samples were collected using a Van Veen grab, box core and grab samples.Sample quality and QA/QC measures varied considerably between the cruises and within each cruise. A critical part of the assessment of the data collected in the Project area was to determine what quality thresholds to use to allow or disallow data to enter into the estimation process. As part of the data verification process, the relative and absolute quality of the data was assessed in as much detail as practically possible. The best samples were those that were collected using the pneumatic grab, sampled the full sand horizon, had a small location survey error and had no other apparent data ambiguities. This paper describes the challenges for mineral resource estimation for an unconventional style of mineralisation using unconventional sampling techniques."

Sep 1, 2014

By Daniel Hodouin, Claude Bazin, René del Villar

"A traditional linkage has long been established at Laval University's Department of Mining & Metallurgy between the Mineral Process (MP) and the Mining Exploitation (Min) on one hand, and between the Extractive Metallurgy (EM) and the Materials Engineering (Mat) on the other. This academic separation of Mineral Processing from Extractive Metallurgy at the educational level has become increasingly at odds with today's industrial practice in which both disciplines are not only complementary but also often intertwined. For instance, in gold ore processing, comminution, flotation, and gravity separation units are interfaced with atmospheric or pressure leaching modules and with carbon adsorption and electrowinning units. The new copper plants in South America combine comminution and flotation circuits with heap leaching, solvent extraction and electrowinning processes.In order to reflect this new industrial reality and to harmonise the options offered in both its engineering programs, the Department of Mining and Metallurgy of Laval University has introduced major changes in its curriculum in 1996. These changes reflect also the recognition that the somewhat secondary status given so far to Mineral Processing and to Extractive Metallurgy within their ""mother"" programs, Mining/Mineral Engineering and Materials metallurgical Engineering respectively, was in sharp contrast with their actual significance for the Canadian economy. Leading industrial voices have raised similar concerns and the Canadian Engineering Accreditation Board has also addressed this problem in its latest program evaluation.The changes implemented at Laval aimed at a) better representing MP and EM within the two undergraduate programs; b) training top-level versatile and multidisciplinary engineers, fluent in all aspects of MP and EM, irrespectively of which of the two ((mother)) programs they had chosen and capable of meeting today's industrial requirements; c) training students in process analysis, optimisation and automatic control using state-of-the-art software, and d) taking into account the co-operative nature of both undergraduate programs.Results are very encouraging in terms of student enrolment and industrial response. However, some concern is expressed on the sustainability of the renewed curriculum considering the drastic budget restrictions in effect at Laval as in most other Canadian universities."

Jan 1, 1999

By H. H. Schrenk, W. P. Yant, F. A. Patty

"INTRODUCTION In accordance with the outline of investigation described in a previous report 5 of the Bureau of Mines dealing with the use of acrolein for detecting leakage of methyl chloride from unit--type refrigerating systems, the work has been extended to include an investigation of its use in a multiple system, This report gives the results of analysis of samples of the gas from representative units of a multiple system charged with methyl chloride containing approximately 0.9 per cent acrolein by volume, The results furnish a basis for estimating the Warning that would be given in event of leakage. The properties and warning intensity of acrolein have been described in a previous report. 5 ACKNOWLEDGMENTSThis investigation was made at the combined request-of Several Inc., Manufacturers of refrigerating, appliances, and the Roeasler Hasslacher Chemical Co., manufacturers of methyl chloride. Acknowledgment is given to R. M. Major, ,chief chemist of the former firm for arranging the experimental site and equipment; to Arthur O. Haseeneall, owner of the apartment building where the investigation was conducted, for his courtesy in permitting the investigation; and to R. R. Sayers, chief surgeon, Bureau of Mines, and surgeon., U. S. Public Health Service, for suggestions and advice."

Sep 1, 1930

By Heikki Laurila, Sirkka-Liisa Jämsä-Jounela, Jarkko Karesvuori

"Artificial Intelligence includes excellent tools for the control and supervision of industrial processes. Several thousand industrial applications have been reported worldwide. Recently, the designers of the A1 systems have begun to hybridize the intelligent techniques, expert systems, fuzzy logic and neural networks, to enhance the capability of the A1 systems. Expert systems have proved to be ideal candidates especially for the control of mineral processes.As successful case projects, an expert system based on on-line classification of the feed type using neural data analysis is described in this paper. The essential feature of this expert system is the classification of different feed types and their distinct control strategies at the plant. In addition to the classification, the expert system has a database containing information about how to handle the determined feed type. This self-leaming database scans historical process data to suggest the best treatment for the ore type under processing. The system has been tested in the Outokumpu Finnmines Oy, Hitura mine. Other projects have been reported to be in progress.INTRODUCTIONIn the past ten years considerable researches have been done in the application of artificial intelligent methods in process industry. The technologies of fuzzy logic, neural networks and expert systems have received several thousand applications worldwide: monitoring and analysis of process operations, fault diagnosis, supervisory control, feedback control and scheduling and planning of operations. Recently, the designers of these systems have begun to hybridize these intelligent techniques to enhance the current capability of expert system. Complex signal processing, neural networks, fuzzy logic and rule-based systems are also implemented to develop new so-called smart or intelligent sensors, actuators or components. Field buses are playing a more and more important role in automation systems and in imbedded systems. The development of field buses has allowed the distribution of smart components over networks."

Jan 1, 2000

By D. J. Dollhopf

The specific objective of this three year study is to investigate the means of reestablishing non-polluted hydrologic systems in areas where surface mining directly impacts shallow ground-water resources. The research area chosen for the study is located near Colstrip, Montana it a new mine site where chemical analysis of core samples from the overburden suggested that excessive concentrations of several elements would he encountered during the mining process. This report discusses local vegetation; soils; and regional geology, and hydrology. Stratigraphic cross sections and regression analyses were used to study the litho-chemical relationships in the overburden. Cross sections indicated Inimical material may be related to both rock tune and position within the overburden profile. In overburden zoness where clay content was high, there was a greater probability that Pb, Cu, Ni, and Mn concentrations would also be higher than average; similarly, the likelihood of overburden exceeding a suspect level became less as the sand content increased. Highest value, of conductance were usually found within a few meters of the surface. High concentrations of clay, nickel, and zinc were frequently found directly above and below the Rosebud coal. Regression analysis indicated overburden SAR was predictable with only a Na analysis. A strong relationship also existed in the overburden between conductance, Ca, and Mg.

Jan 1, 1977

By F. D. Fox

The Flambeau and Ridgeway Mines, both owned and operated by wholly owned subsidiaries of Kennecott Minerals Company, were located very close to populated areas having initial concerns about health, safety and the environment. The success of both operations depended upon developing a framework of community support and enhancing sustainable development opportunities throughout the entire life cycle of the mining operations to address these concerns. The protection of the Flambeau River was the cornerstone of the Flambeau Mine’s success. The highest priority for the Ridgeway Mine was to ensure long-term physical, chemical and ecological stability of the reclaimed mine site. Both of these goals have been achieved and are discussed in this paper, which highlights Kennecott Minerals Company’s integration of sustainable development principles into its business decision-making and management processes.

Jan 1, 2003

By R. F. Waters

Laboratory-scale selective volatilization methods developed by the Bureau of Mines to recover germanium and gallium concentrates from coal fly ash and phosphorus furnace flue dust are summarized. In the better experiments between 85 and 98 percent of the germanium was recovered as the lower oxide and as sulfides, and between 75 and 97 percent of the gallium was recovered as the lower oxide and as the trichloride. Grades of the condensates were inconsistent and varied between a few tenths of a percent and 8 percent, depending on the method used. In the primary extractions of germanium alone the degree of enrichment surpassed 100 to 1, and for gallium the best ratio was 30 to 1. Upgrading of condensates by vaporization retreatment and by leaching and precipitation is discussed. An appreciable degree of mechanical preconcentration by attrition scrubbing and elutriation was possible on two fly ash samples.

Jan 1, 1967

By J. A. Caceres

Mining planning and mineral processing are almost two unconnected areas. The mining area builds its economical models considering the plant like a constant parameter: a constant throughput, an average recovery and a unitary cost. On the other hand, the mineral processing area assumes a mine plan with grades, ore type, work index, estimating the performances in an independent way. Previous researches have evaluated the advantage for increasing throughput by increasing the liberation size, thus sacrificing recovery. These valuables approaches have left behind the work index factor, critical variable for Recovery-Throughput capacity estimation. This study describes a method combining mineral processing and mining planning. This method incorporates the grinding and flotation performances into the mining economic models optimizing simultaneously the Throughput- Wi(Work index)- Recovery relations with mining sequence, cut-off strategies, and reserve schedules. This method has been used at Andina Mine Chile, showing 18% net present value increasing with minimum investment associated.

May 1, 2003

Note this date. This will be the biggest meeting we have ever held. It is arranged so as to permit you to go immediately afterwards to Salt Lake. City to attend the meeting of the American Institute of Mining and Metallurgical Engineers there on August 31, September 1, 2 and 3. Notify the Secretary of any change in your address.

Jan 1, 1925

By Roberto Maldonado

El presente texto señala el proyecto de profundización en la mina Animón considerando sus características como: geología e hidrogeología, parámetros geomecánicos, niveles de producción, costos de capital y operación, eficiencia del sistema, flexibilidad para cambios en las operaciones, reservas de mineral y consistencia con el sistema de explotación. De forma que a través del conocimiento de estas y de las herramientas gráficas tridimensionales, se pueda analizar las diferentes alternativas, incluyendo condiciones que debe cumplir el proyecto de profundización, el cual abarca también los servicios auxiliares y ventilación.

Sep 12, 2005

By G. L. Oldright

This paper is the third1 of a series of five papers that is to appear on smelting in the lead blast furnace. The objects of this investigation are to determine the conditions obtaining within the blast furnace be direct experimentation, and to correlate the behavior of the furnace at various times with the main factors governing the operation of the blast furnace, and metallurgical losses. ACKNOWLEDGEMENTS The writers wish to express their appreciation to the management of the international Smelting Company at Tooele, Utah, for their kind cooperation which made possible the assembling of these data.

Jan 1, 1929

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, Matthew Gordy, Patrick Zhang

Waste phosphatic clay presents a difficult disposal problem and a significant loss of P2O5. Recent developments make this study on the use of phosphatic clay as a feed material for H3PO4 production worthwhile. (a) New data from Florida Industrial and Phosphate Research Institute (FIPR) suggest that the Bclay^ waste can be effectively treated by improved solid separation coupled with flotation to produce feed material for recovering additional phosphate. (b) The use of BOLI Flowsheet^ provides capability to predict performance of aqueous-based processes for a range of possible operating conditions. Using the new FIPR data and BOLI Flowsheet^ enabled the design of a new process that can potentially extend the usefulness of current P2O5 ore deposits. Predictions using OLI Flowsheet were able to identify process conditions that effectively overcome the difficulty of high Mg content of phosphatic clay. Estimated manufacturing cost in the current study lead to valuation of the P2O5 content of the phosphatic clay recovered/utilized at 60 to 70% of that of the phosphate rock feed material currently used. Phosphatic clay should be considered as a valuable material that is currently given zero value. The new FIPR data and BOLI Flowsheet^ enables the design of a new process that can potentially extend the usefulness of current phosphate ore deposits by extending the fraction P2O5 of recovered

By L. Mabiza

Keywords: Pyrometallurgy, furnace, sulphur, SO2, off-gas, Zimplats Zimplats embarked on an off-gas sampling campaign in December 2009 to characterise the concentration of SO2 in the off-gas from their 13 MW furnace. In excess of forty isokinetic samples (US EPA Method 8) were taken over seven days. The aim of the sampling campaign was to increase the understanding of factors that influence sulphur release from sulphide concentrates in an electric furnace. Specifically, detailed monitoring was conducted over various operating conditions to evaluate: ? The relationship between SO2 and feed rate (i.e. furnace power) ? The relationship between SO2 and ingress (i.e. furnace freeboard pressure) ? The impact of concentrate bed thickness on SO2 (i.e. blacktop) ? The effect of events such as tapping and converter slag return on SO2 ? The desulphurization reactions that take place in the blacktop A model was developed to predict the SO2 content in furnace off-gas for a particular set of operating conditions. In order to evaluate the impact of random, uncorrelated changes in concentrate composition, ingress and power (feed rate) on the SO2 content of the off-gas, a Monte Carlo approach was adopted whereby concentrate composition, power, and ingress were allowed to vary randomly around selected set-points. The model is primarily based on the release of ?labile? sulphur from the partial thermal dissociation of sulphide minerals with an over-stoichiometric sulphur content (e.g., Fe7S8 decomposition to FeS and S). The main findings of this work suggest that labile sulphur does not fully account for the measured SO2 content of the off-gas, and that limited oxidation of sulphides during melting also contributes to the SO2 content. Details of sulphide oxidation reactions in the furnace remain unclear, and it is currently not possible to provide a theoretical framework for the relationship between the extent of oxidation and variables such as temperature, gas composition, particle size, and residence time in the furnace black top. Through the use of the Monte Carlo model it was, however, possible to constrain the extent of sulphide oxidation to about 1%. This work has shown in practice what was expected in concept, that SO2 in off-gas is proportional to furnace power and ingress rate. The model that was developed consistently slightly under-predicts the quantity of SO2 generated. It also highlights that more work is required to better understand the analytical methods used to analyse for SO2 in off-gas.

Jan 1, 2011

By Chunhui Zhang, Enton Bedini, Jiang Chen, Fengchao Yang, Hang Dong, Xiaoyan Chen

The alteration formed by the reaction of ore-bearing fluid and wall rock is often used as an important prospecting indicator, resulting in the dilution or enrichment of metals or related trace elements. A variety of rock-forming and metallogenic elements have been analyzed in regional stream sediments so that the relationship between the ore-bearing altered rock and the change in the geochemical elemental content can be obtained. Therefore, by using appropriate models, such as matched filtering, the abundance of the distribution of wall rock alteration, similar to the discovered deposits, can be modeled by using the distribution of geochemical elements in the region, and the areas with high distribution abundances are usually favorable prospecting targets. The alteration types related to gold mineralization in the Baiyun gold deposit are potassium feldspar alteration, silicification, pyritization, sericitization, and chloritization. In this paper, the geochemical data of the Qingchengzi ore field (1:200,000 and 1:50,000) have been used to form geochemical images through rasterization. In the three sections of the Baiyun gold deposit, binary-coded curves have been formed, revealing the differences in geochemical elements in stream sediments between altered rocks and the rocks surrounding the Baiyun gold mine. Among them, Au, W, and Mo are enriched elements, while Sn, Zn, and Hg are depleted elements. Several gold deposits are found in the predicted altered rock area by using the matched filtering method during fieldwork, which shows the effectiveness of the method.

Dec 30, 2023

By A. V. Aleksandrov, T. N. Aleksandrova, N. V. Nikolaeva

Using complex thermal analysis methods, flotation concentrates were classified depending on what the organic and nonorganic carbon form is. The possibility of ultrafine particles of valuable components (noble metals and diamonds) extraction using physical actions of different genesis in the processing of ‘unconventional’ mineral raw materials is considered in the paper. Electromagnetic treatment is one of new technologies in the field of mineral processing. The features of the electromagnetic effect on substances include uniform heating throughout of the volume, high speed and low inertia of heating, as well as the possibility of selective heating. A selection of studies including gravity, flotation and extraction methods of enrichment using energy effects, as well as thermal analysis was conducted to establish the availability and possibility of extracting valuable components. Due to microwave and high-temperature exposure, minerals and gas-liquid inclusions are decremented, and crystal-chemical water is released, resulting in additional defects. As a result, self-cleaning of sulphide minerals from atoms of scattered gold occurs by distilling it into peripheral parts of grains and intergranular space, where ultradispersed individuals are formed. Keywords: Refractory gold-bearing ores, physico-chemical properties, ore preparation, flotation, modelling, simulation, selection

Jan 1, 2020

By E. S. Leaver

The gold that is not recovered by a particular process is refractory to that process. A study to determine how the refractory gold is associated in the ore constituents usually indicates the needed improvement in the process or additional methods for bettering recovery. In preliminary work, segregation of the various minerals, gangue or impurities, and data showing the reactions of each in the recovery method readily confines the refractory gold to a certain part on which extensive research can be directed. In this dissecting plan, the microscope is an important aid in locating the refractory gold but should be supplemented by chemical tests.

Jan 1, 1934

By Fernando Cillóniz

Benchmarking es un proceso de comparación y medición de los procesos de negocio de una organización, con aquellos que lideran el mercado. De forma que se obtiene información para mejorar el desempeño de las empresas. En ese sentido, el presente texto señala la utlidad del Benchmarking en las empresas donde el uso de la Internet y las tecnologías de la información permiten hacer más eficiente las comparaciones e intercambio de experiencias y conocimientos, así como internacionalizar el proceso.

Aug 25, 2002