Search Documents

By R. Hamilton

"Louvicourt mine began operation in 1994. It is located in northwestern Quebec, 20 km east of Val d’Or. The mine is owned by Aur Resources (30%), which operates the mine, Teck/Cominco (25%) and Novicourt (45%). By the end of 2002 there were approximately 280 employees working on the site, including contractors. Production averages 4300 tons per day, working a massive sulphide body located between 415 m and 920 m underground.Maintenance expenses represent 27% to 29% of the operating costs, and the maintenance personnel represents 34% of the total workforce (including electrical, mechanical and concentrator maintenance staff). Considering these figures, in addition to capital costs and indirect costs, such as energy (electricity, fuel, gas, etc.), it is worthwhile to pay attention to how things are done in order to protect such investment. Every task performed to help understand the impact of Louvicourt’s practices must to be seen as an investment in the reliability of its operation."

Jan 1, 2003

By J. Wickens

Haile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The relatively low grade and refractory nature of the deposit has been a challenge for efficient processing since the start of mining on the property. Early processing techniques included gravity separation and barrel chlorination. The last operation employed heap leaching in 1985 through 1992. After being closed and reclaimed for over 20 years, the property is poised to re-open and produce once again. In this chapter of the Mine?s legacy, flotation and ultra-fine grinding will be employed to achieve economic extraction of gold and silver from the pyrite. This paper briefly reviews some of the mine?s history, the metallurgical testing, the flowsheet and discusses design considerations. KEY WORDS: process plant, flash flotation, leaching, SMD, stirred media detritor

Feb 27, 2013

Grey River Gold Mining Limited (GRGML) has constructed and largely completed the commissioning of an alluvial gold dredge designed to recover gold from a low grade gold deposit in the Grey River Valley, New Zealand. The most important resource that GRGML has are the people who are employed by the organisation. The low grade of the deposit necessitates the requirement to operate the dredge at optimum efficiency, which in turn requires the work force to be of high calibre and continually motivated. The primary prerequisite for employment at GRGML is for employees to be receptive to new ideas and have the adaptability to develop new skills and apply those skills to the changing demands of the workplace.   A continually changing organisational structure is utilised to meet the needs of a changing work environment. The adoption of an innovative site employment agreement allowing for flexible working hours has aided the achievement of good employee productivity and attendance.   Employees gain a higher quality of life by working a roster pattern involving twelve hour shifts and a four day on, four day off pattern.   Employees and management are communicating very well and working together to achieve organisational goals which will ultimately benefit the employees, the shareholders, the local community and the mining industry generally.

Jan 1, 1989

By Matthew P. Wickham

The use of existing mine records in conjunction with an appropriate classification scheme can be used successfully to identify and characterize the composition of existing waste rock facilities where traditional approaches based on sampling may be impractical or costly. This paper describes an alternative approach used in an acid rock drainage investigation at a porphyry copper mine with numerous waste rock dumps of varying ages and composition. The approach integrated detailed lithologic and mineralogic information about the ore body and overburden materials with records of pit development and dispatch. A waste rock characterization matrix was developed for the site to meaningfully classify lithology and mineralogic composition of the waste rock. The approach resulted in a focused geochemical testing program and facilitated interpretation and application of the test results.

May 1, 2002

Electrostatically charged water droplets efficiently suppress breathable dust produced during open air rock crushing operations, according to recently completed independent tests conducted for the Environmental Protection Agency. Since a primary rock crusher produces very heavy clouds of dust, this application was selected as an appropriate test site to measure the efficiencies of new "charged fogging" equipment in mining and mineral processing operations. EPA's Industrial Environmental Research Laboratory, Research Triangle Park, NC, contracted TRC-Environmental Consultants Inc. of Wethersfield, CT, to conduct a full-scale demonstration of a recently developed electrostatic fogger, designed to project a charged fog spray at distances up to 15.2 m. Test results indicated overall fogger efficiencies of approximately 70%. The Fogger IV* employed in these tests is reportedly the largest charged logger ever made, with an extremely long operating range. The original fogger was designed for indoor dust control; this fourth generation version is designed for fugitive dusts, indoor and outdoor, and has an operating range up to 15.2 in.

Jan 6, 1981

By Gustavo Armijo

Slippery and unstable working platforms spoiled not only by natural weather conditions but also by the effects of the construction process (drilling mud, grout slurry) are among the main sources of hazards. Due to this fact a set of recommendations for execution and maintenance of working platforms are presented in this paper, which is based on a study on this subject that is being carried out by AETESS, the Spanish Federation of Geotechnical Contractors. The main objective of this paper is to establish the basis for the right execution and maintenance of working platforms for geotechnical jobs with the idea of increasing safety and productivity. All the aspects involved in working platform safety are analyzed: ground and equipment characteristics, geometric conditions and working platform maintenance. From this analysis a set of general requirements is proposed together with the necessary specific controls before and after the equipment arrival to the job site. In order to facilitate this analysis some flow charts and tables and specific appendixes for each geotechnical technique are included.

Jan 1, 2006

By Allen W. Hatheway, John A. Albritton, Lloyd B. Underwood

Missouri River Division (FORD), U.S. Army Corps of Engineers (COE), has completed (October 1982) a study for the U.S. Air Force Ballistic Missile Office, in which desireable and needed changes in contracting methods for underground construction were identified. Due to the importance of geotechnical considerations in such construction, a good number of the resulting recommendations relate to geotechnical considerations. Corps contracts have traditionally served as models for contract documentation by public agencies and in private enterprise. Several standard features of present-day contracting methods were Corps innovations. Corps officials are generally in agreement with the recommendations of the Better Contracting reports published by the U.S. National Research Council (NAS/NRC), through its U.S. National Committee on Tunneling Technology (USNCTT). However, the findings of the 1982 MRD study indicate that additional changes are warranted for underground construction contracting methods; changes that deal specifically with site geological conditions, both known and to be reasonably anticipated, as well as with their associated impacts on construction. The 1982 MRD report identifies the need for nine specific improvements in geotechnical aspects of contracting; improvements based on recognition of geological conditions.

Jan 1, 1983

By Shahriar Vandani, Andy Herlache, Andrew Bro, Wei-Yu Chen

"The Presidio Parkway Project will reconstruct approximately 1.6 miles (2.6 km) of highway, including seven new bridges, three new cut-and-cover tunnels, and a new undercrossing connecting the Golden Gate Bridge to the City of San Francisco, California. The project site is approximately 5.6 miles (9 km) from the San Andreas Fault, capable of producing magnitude 8 earthquakes. Seismic hazards include strong ground shaking, soil liquefaction, ground settlement, and lateral spreading. The Main Post Tunnels (MPT) are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) long. The MPT site underlain by loose sandy soils susceptible to liquefaction and lateral spreading. Excessive racking and permanent displacement due to lateral spreading are identified as the main seismic vulnerabilities. Analyses showed that without ground improvement, tunnel racking of over 5 inches (13 cm) and permanent lateral tunnel displacement of up to 15 feet (4.6 m) could be anticipated. Cement Deep Soil Mixing (CDSM) is proposed to mitigate slope displacements and increase lateral stiffness of the foundation materials to reduce tunnel racking. A series of 2-D fully dynamic time domain analyses were performed to evaluate the performance of CDSM, confirm that performance criteria are met, and optimize the CDSM geometry and replacement ratio. The use of CDSM reduced the permanent tunnel displacement from over 15 feet (4.6 m) to less than 1 inch (2.5 cm). Tunnel racking was also reduced significantly. The adopted analytical approach presented herein can be considered for future tunnel design projects in seismically active areas.Introduction The Main Post Tunnels (MPT) are an integral component of the Presidio Parkway project which will replace the existing facility with a new multi-lane roadway between the Golden Gate Bridge and the City of San Francisco. The MPT are two parallel cut-and-cover concrete tunnels approximately 1100 feet (335 m) in length. As shown on Figure 1, the project site is located in a seismically active area, about 5.6 miles (9 km) east of the San Andreas Fault and 12.5 miles (20 km) west of the Hayward Fault. The San Andreas Fault can generate magnitude 8 earthquakes while the Hayward Fault is capable of producing magnitude 7.3 earthquakes. The design Peak Bedrock Acceleration (PBA) is 0.46g for the upper level design earthquake. The project alignment is shown on Figure 2."

Jan 1, 2014

By Michael Hood

An overview is given of some of the major mining research activities in Australia. Automation of mining equipment is not an objective in its own right. The objective is to improve the safety and the economic performance of mining operations. Automation can be a useful method for achieving this objective. There is a strong focus on mining equipment automation and related issues and specific examples of ongoing and recently completed automation projects are described.

May 1, 2002

By James P. Stewart

This case history describes the engineering design and construction for the Contractor of a 35-ft-deep excavation for an 800-square-foot addition to an existing sewage pump station. The site posed unexpected geotechnical complications that included deep gravelly soil, a history of local construction difficulties, groundwater consisting of heavy salt brine, and the need to underpin the existing pump station. The project took an interesting twist when the Owner issued a change order limiting the dewatering discharge to a fraction of that required to lower the water table. This documents the interesting circumstances of this job and documents the unusual subsurface conditions in the Syracuse, NY Lakefront area.

Jan 1, 2003

By A. Roberts

This paper reviews progress in equipment design and in the techniques applied to mine lighting in Great Britain. The incidence of the disease miner's nystagmus, which was a major source of concern only a few years ago, has now diminished, largely owing to improvements in standards of lighting in mines. The reorganisation of the coal mining industry, involving increasing mech-anisation, together with new safety legislation, has brought about the widespread use of mains electric lighting underground. An account is given of some of the results of research to determine the lighting conditions needed for compliance with the compulsory legal requirement of "sufficient and suitable" general lighting at specific localities in British mines. Some details are given of the techniques applied and the results of recent research in the problem of glare from miners' cap lamps. Of the various factors in the working environment of the miner, it is true to say that lighting is seldom given attention comparable with that devoted to other factors, such as dust, heat and humidity, or atmospheric gas content. No doubt one reason for this lies in the ability of the human eye to adapt itself to low brightness levels. Be that as it may, the fact is that at the turn of the 20th century the miner's working light improved little throughout the centuries during which mining technology has developed. Indeed, in coal mines which encounter a methane explosion hazard, flame safety lamps, with a luminous intensity less than one candle power, were virtually the sole means of lighting during almost the whole of the 19th century. The 20th century has witnessed a substantial improvement in lighting techniques underground in coal and metalliferous mining. In Great Britain the general pattern has been one of standards periodically raised by the implementation of Statutory Regulations imposed under successive hlines Acts, but it is fair to add that the more progressive mining companies usually anticipated the Statutory Regulations, which when they have been put into effect have served to turn into general practice what was already being done at the better mines. In earlier years, official requirements were limited to the specification of approved lamp designs, with stipulated minimum values of luminous intensity and light output, but more recently the necessity of satisfactory maintenance of standards during service has been recognized, and the current regulations not only require that a maintenance organisation should exist, but also specify a maximum permissible depreciation below initial approval standards.'

Jan 1, 1961

By H. E. Hawkes, D. A. Barr

Time variations in the copper content of the sediments of streams draining mineralized areas were studied in two areas of contrasting climatic environment, one in northern and one in southern British Columbia. In each area, samples were collected and observations made of rainfall, stream discharge and air and water temperature at intervals throughout the summer season. Samples were analyzed for total and cold-extractable copper. Results showed a weak inverse relation between cold-extractable copper and discharge in two out of the three test sites in the southern area, and a decrease in ratio of COld-extractable to total copper over the duration of the test period at a highly anomalous site in the northern area. In suspended rock flour resulting from glacial erosion of mineralized rock in the northern area, virtually all the copper was found to be soluble in cold, dilute hydrochloric acid. None of the variations observed is sufficient to cause serious problems in geochemical sediment surveys. Systematic collection and trace analysis of stream sediments has seen wide application in recent years as a method of primary prospecting in primitive areas. Common practice is to collect fine-grained samples of sediment either from the active channel or from the flood plain near the channel. Samples are dried, sieved and the -80-mesh fraction analyzed after breakdown of the sample by a relatively strong attack, such as by fusion or by treatment with hot perchloric acid. Drying, sieving and rigorous chemical attack requires established facilities, either in a well equipped central laboratory or in base camp. Thus analysis for total metal involves a substantial delay from the time the samples are collected until the analytical data can be reported. An alternative system uses a cold aqueous extrac-tant in place of the hot acid or flux.4 Advantages of the cold-extraction techniques are that kits can be prepared for use directly at the sample site and that, in some problems, the patterns in cold-extractable metal, usually abbreviated cxMe, are more useful as ore guides than the patterns in total metal.' In the course of operational geochemical sediment surveys, a problem that has come up repeatedly is failure to reproduce anomalous values or patterns by resampling the same areas. The mystery of the vanishing anomaly has led to speculation as to whether there is a significant variation in the metal content of sediment samples with the weather or with the time of year. Review of the published literature shows that a number of experiments have been carried out on time variations in the metal content of stream water.1,2,5,7-9 The only published report on time variations in stream sediments that has come to the authors' attention, however, is by Govett,3 working in Northern Rhodesia.

Jan 1, 1963

The Bureau of Mines is operated to assist in promoting economic development through increased efficiency in the mining, preparation, treatment, and utilization of mineral substances; to aid in conserving mineral resources through preventing waste; and to help the mining industry improve health conditions and increase safety. Accomplishment of those ends is sought through investigation of scientific, technologic, and economic problems of the, mineral industries and dissemination of resulting information. Building materials of mineral origin constitute an important product of mining, and the Bureau makes studies of these in the various fields mentioned. The following commodities come within this classification: Asbestos, anhydrite, asphalt, cement, clay and clay products, diatomite, dolomite, glass and mineral wool, granite, greenstone, gypsum, lightweight building materials, lime, limestone, magnesite, marble, sand, sand and gravel, sandstone, sand-lime brick, slate, soapstone, and trap rock.

Jan 1, 1937

The intent of this manual is to provide guidelines for inspectors of drilled shaft construction otherwise referred to as drilled piers, caissons or bored piles. It should also be helpful to train beginning geotechnical engineers with limited first hand experience or for geotechnical engineers who are training inspectors. It is expected that the general guidelines and procedures described here will be supplemented by local geotechnical engineers working in a particular region based on local practice and experience. Since drilled shaft construction procedures vary widely based on local geology and size of project, an all-inclusive manual is not considered practical. This manual focuses on traditional topside inspection for routine drilled shaft construction. Other inspection and evaluation methods that rely on electronic equipment are available, but these methods require extensive training and experience in the interpretation of results. These more sophisticated methods of drilled shaft inspection and evaluation are common in construction, but they are usually provided by specialty subconsultants. The subconsultant will typically submit a report for each shaft, which will be reviewed by the geotechnical engineer. Other manuals are available to describe the electronic methods of drilled shaft inspection.

Jan 1, 2004

It's long been suspected that there has been an increase in the incidence of premature failure of rock bolts in underground coal mines over the past ten years. As far back as 2002 a study found a possible contributor to such premature failure in some Australian coal mines might be linked to stress corrosion cracking (SCC) (Crosky et al, 2002). That study suggested the low impact toughness could be a major influence on the susceptibility to SCC of different steel compositions. A subsequent study involving laboratory corrosion tests however failed to confirm any link with metallurgical factors (Villalba and Atrens, 2007), a finding that is at odds with field experience. Some mine sites today are still reporting prematurely failed rock bolts to the rock bolt manufacturers; the failures are being identified at SCC induced. To this end a research project has recently been commissioned at University of New South Wales (UNSW), which aims to identify the environmental factors causing SCC, through field test sites and simulating the conditions within an accelerated corrosion laboratory. This paper outlines the methodology that will be used in this study.

Nov 25, 2010

Contact Angle Measurements on Lignite Surface

Sep 13, 2010

By Donald Bruce

The three types of specifications which are used for micropile work are: ? Performance Specifications: The contractor is permitted control over certain design and/or construction procedures but must demonstrate to the owner through testing and/or certification that the final product meets the specified performance criteria. This method allows and encourages the contractor to provide a competitive and/or innovative micropile design within the framework of the overall design requirements. The responsibilities for the work are shared between the owner and the contractor. ? Open Specifications: These leave the scope and design of the installation up to the micropile contractor. This method is the most common for securing bids on temporary micropile work. The responsibility for design and performance is clearly placed on the contractor. Open specifications are not recommended for permanent applications. This method allows the contractor to select the most economical micropile system. ? Prescriptive Specification: The Owner describes specific procedures that must be followed, but which may not necessarily describe the objective of the work. When prescriptive specifications are used, the owner is responsible for the proper performance of the system. The contractor is responsible for satisfying the details of the specifications. Performance specifications are the most common and best reflect the challenges and interests of micropile technology and applications.

Jan 1, 2004

By Joint Micropiles Committee

"The three types of specifications which are used for micropile work are: • Performance Specifications: The contractor is permitted control over certain design and/or construction procedures but must demonstrate to the owner through testing and/or certification that the final product meets the specified performance criteria. This method allows and encourages the contractor to provide a competitive and/or innovative micropile design within the framework of the overall design requirements. The responsibilities for the work are shared between the owner and the contractor. • Open Specifications: These leave the scope and design of the installation up to the micropile contractor. This method is the most common for securing bids on temporary micropile work. The responsibility for design and performance is clearly placed on the contractor. Open specifications are not recommended for permanent applications. This method allows the contractor to select the most economical micropile system. • Prescriptive Specification: The Owner describes specific procedures that must be followed, but which may not necessarily describe the objective of the work. When prescriptive specifications are used, the owner is responsible for the proper performance of the system. The contractor is responsible for satisfying the details of the specifications.Performance specifications are the most common and best reflect the challenges and interests of micropile technology and applications.The owner, designer and contractor will together be responsible for the tasks associated with the design, installation, acceptance, and performance of the micropiles. The installation of micropiles requires specialized equipment, techniques, and appropriate workmanship. Not every detail of the work can be specified, and not every potential problem can be anticipated. Therefore, a contractor who has demonstrated experience in micropiles must be selected to execute the work required."

Jan 1, 2004

By Thomas W. Camm

This study was done to evaluate the costs of various dumping operations at waste and spoil piles. It has been theorized that accidents associated with dumping operations might be reduced by short-dumping rather than edge-dumping, but many operators have been reluctant to use short-dumping because they believe it is not as cost effective as edge-dumping. To evaluate this perception, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health reviewed the costs of various dumping methods at waste and spoil piles. The study found that overall cost differences between the two methods were not significant in most cases. However, while overall cost differences between the two methods appear small, capital costs could be more significant when short-dumping if numerous dump sites are used concurrently. The choice of which method to use should be based on considerations of the safety of dozer and truck operators.

Jan 1, 2000

By D. Ksinsik, R. Boisvert, D. Leblanc

Casting, cooling and crushing/sieving of ferroalloys has followed a well-established pattern in the whole ferroalloys industry for many years. Usually liquid metal or alloys are cast into flat open moulds of various shapes and forms, and after solidification the product is removed from such mould to further cool down to a temperature where subsequent handling steps are feasible. Common to all mechanical product fractioning is the generation of dust and fine size material with lower product value. For almost 10 years, Bécancour Silicon has investigated alternative roads to improve technology and/or reduce or solve problems related to those disadvantages. Since 1995 Bécancour Silicon operates a special silicon granulation plant targeted to product for the chemical treatment/conversion of silicon for silicones production. Prior to the development of the granulation process, various systems had been evaluated, among others the vibrating casting bed, now in operation elsewhere but judged inappropriate because of the tapping volumes to be handled at Bécancour Silicon and other disadvantages. After evaluation of all aspects of heat transfer, radiation, and conductivity in relation to transfer media and within the product, a novel system was designed and built.

Jan 1, 2004