Search Documents

By L. Harris

The gold mining and ore processing operations of Minera Yanacocha S.A. are 10cated in an area 4,000 meters above sea level in the Peruvian Andes same 600 km north of Lima and 20 km north of Cajamarca. The joint venture partners are Newmont Second Capital (USA); Compania Minera Condesa (Peril); Mine Or (France) and the IFC. Newmont manages the operation. The Yanacocha district comprises several areas with mineralization evidence. The first ore with minable reserves of 28 million tonnes of ore assaying about 1.4 gpt Au is called Carachugo and is being mined and treated at the rate of 14,000 tonnes of ore per day by open pit mining methods. ROM ore is dump leached and the gold recovered in a Merrill Crowe plant. The plant design incorporates some unusual considerations to overcome the problems of the high rainfall in this area and assure the protection of the environment.

Jan 1, 1994

By Peter Grandstone, D. A. Jessup, D. B. Taliaferro

"INTRODUCTION Water flooding of oil sands in Texas as a means of secondary recovery of oil has been practiced mainly in the north-central part of the State, which includes the old shallow fields in eight counties, extending south through Wichita and Clay Counties on the Red River into Brown County.The Texas Railroad Commission, is empowered ""to promote conservation and prevent waste in the drilling, completion, operation, and abandonment of oil wells"" and ""to issue regulations necessary for fulfillment of these ends,"" granted The Texas Co. the first permit to inject water into the oil-bearing sand on December 7, 1935. The permit was granted after the Commission had conducted a number of hearings, which were attended by many operators interested in that method of secondary recovery. Through December 31, 1944, the Commission had granted 50 permits for water flooding. Of that number, 45 permits were issued for projects in north Texas, the remaining 14 being distributed throughout west and south Texas. By the end of 1944, there were 33 active and 5 abandoned water-flooding projects in the North Texas area, as is in figure I.Oil production in the North Texas area started in 1904 from the shallow sands (ranging from 100 feet to 800 feet in depth) of the Petrolia (or Henrietta) field in northern Clay County. Development was rapid and unrestricted during the boom period from about 1911 to 1918, and considerable waste of both produced oil and reservoir energy resulted."

Jul 1, 1946

By T. K. Bundtzen

Placer gold in the Iditarod and Innoko mining camps of western Alaska is derived from a suite of comagmatic, Late Cretaceous to Early Tertiary, alkali-calcic, meta-aluminous. volcanic-plutonic complexes and peralumi-nous rhyolite sills that intrude Mesozoic flysch. Heavy-mineral concentrates from 42 mining operations and streams draining known mineralized areas in the igneous complexes contain placer gold and a variety of ore minerals derived from epithermal to hypothermal conditions of formation. The minerals include cassiterite, ilmenorutile, samarskite, cinnabar, scheelite, chromite, stibnite, silver sulfosalts, monazite, and zircon. Results of the study show that 1) cinnabar. stibnite, and quartz formed with the bulk of the placer gold in an epithermal lode environment, 2) chromite appears to have originated in mafic phases of monzonite plutons and alkalic basalts, and 3) niobium-tin-tungsten-uranium-silver values may have been derived from stockwork accumulations in cupolas of monzonite plutons.

Jan 1, 1987

By M. Z. Emad, N. Abbas, Y. Majeed

Room-and-pillar mining is commonly employed for the extraction of rock salt in undergroundmines. Pillar stress is a major concern in these mines as it is directly related to stability and mineralrecovery. In this study a flat jack method was used to measure pillar stresses in three undergroundrock salt mines in Pakistan. The field work included determination of in-situ stress, in-situ elastic modulus, recording of field variables (pillar length and width, height and width of opening, opening width to height ratio, extraction ratio, and overburden height) and collection of salt block samples. The geomechanical properties of rock salt (uniaxial compressive strength, Young’s modulus, Brazilian tensile strength, and density) were also determined to estimate overburden stress, pillar strength, and factor of safety (both estimated and actual). It was found that the measured pillar stresses are proportional to the overburden stress values, with their magnitude ranging from 6.05 MPa to 11.97 Mpa, and the pillars were found to be stable. Regression analysis was performed to develop statistical models for in-situ stress and in-situ elastic modulus. Finally a quick guideline chart was developed to determine the suitable length of pillar for a given span and required level of safety.

Jun 5, 2023

By L. H. Harrison

In coal mines equipped with electrically driven mechanical mining equipment, the problem of protection for electrical circuits and machinery important, because the hazards of fires and explosions resulting from electrical failures is greater than in most other industries. There is need for better methods and improved protective devices for this service. Studies and tests designed to determine possible value of the short-circuiting contactor as an electrical device for coal mine service were investigated. Preliminary made to determine the operating characteristics of the device, after which tests were made under actual service in three coal mines. Ordinarily, electrical protection in coal mines is divided into three classes, as follows: 1. Overload protection that is intended to protect against damage from overheating and excessive mechanical strain due to overloading. 2. Short-circuit protection that provides a means of de-energizing the equipment instantly when an accidental short circuit occurs in the equipment or on the power system. Short cm protection tends to damage from fires and, explosions resulting in the dissipation of large amounts of electrical energy in a short circuit. 3. Ground fault protection that, in its various forms, is intended, to maintain the frames of electrical equipment at or near the same potential surfaces in contact with the earth for the purpose of safe-guarding human life.

Jan 1, 1951

By J. A. Gutierrez-Rodriguez, R. J. Purcell, F. F. ApIan

"Based on contact-angle measurements and the work of adhesion equation, the hydrophobicity of a wide variety of coals was found to decrease with decreasing rank, fixed carbon and total carbon content and with increasing oxygen and hydroxyl content. The estimated hydrophobicity, based on the water-sessile-drop contact angle, is '\.. 20% for lignite, increases with increasing rank up to a maximum of 'V70% for low (LV) and medium (MV) volatile bituminous coals and then decreases somewhat for anthracite. Using the captive-bubble technique, the calculated hydrophobicity ranges from '\.. 0% (below HV A bituminous rank) to a maximum of 55% for L V-MV coal. The former estimation is believed to be the more accurate. While the water-sessile-drop contact angle as measured on a polished-coal surface is usually larger than that shown by the captive-bubble method, the two values were found to converge at""' 95% relative humidity. It is proposed that the surface of coal consists of three kinds of sites: strongly hydrophobic, weakly hydrophobic and hydrophilic. The sessile-drop technique measures the total hydrophobic sites whereas the captive-bubble method measures only the more strongly hydrophobic sites. A water film covers the weakly hydrophobic sites preventing their detection by the captive-bubble technique.INTRODUCTIONCoal is a mixture of the degradation products of plants and of mineral matter. The appearance and properties of a specific coal is determined by the nature of the original vegetation and the extent of the physical and chemical changes which have occurred after deposition. The coalification process may be considered to have started with peat formation followed by a transition to lignite due to burial under sediments and metamorphic processes. Further metamorphic transformation to bituminous coals and, finally, under intense metamorphic action, to anthracite causes the carbon content and rank of the coal to increase. With such a wide variation in their genesis and composition, equally wide variations in the degree of hydrophobicity of different coals may be expected. It is the purpose of this paper to provide a means of estimating the hydrophobicity of a given coal sample based on rank parameters."

Jan 1, 1989

By R. W. Raymond

THE sudden death of Dr. Drown, on Nov. 17, 1904, brought to multitudes the pang of personal loss. Of all those who, as students at Lafayette College, the Massachusetts Institute of Technology and Lehigh University, were brought under his influence, not one can have forgotten him, and all will now acknowledge, with an unfading gratitude, what they owe in professional equipment to his wise, clear, skillful guidance, and in character to his sympathetic, stimulating personality. Outside of this wide circle, the experts of both hemispheres will lament the departure of one who, in his department of scientific inves¬tigation, both knew what work was needed, and how to do it so that it needed not to be done again. The older members of the American Institute of Mining Engineers will remember with gratitude the part he took, as Secretary from 1873 to 1884, in promoting the interest of that organization, and in shaping the plan and policy which it has followed with such noteworthy success. And, in addition to all these (though partly included among them), there are a host of friends; who can scarcely think of the public loss by reason of their own. Thomas Messenger Drown was born March 19, 1842, at Phil¬adelphia, Pa. His parents were natives of New England; and. he was the youngest of their three sons. He received his preliminary education in the public schools and the High School of Philadelphia, from which he was graduated in 1859. Be-

Jul 1, 1905

By J. Zollinger, J. R. Kennedy, J. H. Park, D. Daloz

"In order to improve the properties of cast Ti-Al alloys to replace Ni-based superalloys past the low pressure stages of aircraft engines investigations into inoculation for grain refinement were carried out. Previous work showed isomorphic self-inoculation using Ti-Al-Nb particles was effective for grain refinement, however the relatively fast diffusion of Nb in Ti-Al make it difficult to observe the mechanism of nucleation. An alternative alloy was developed in the Ti-Ta system for isomorphic self-inoculation, maximizing the Ta content to improve the particles survivability in the melt. The powder processing produced comparatively small inoculant particles which dissolved, however larger particles were seen to survive solidification. The density difference between the inoculant particles and melt resulted in an inhomogeneous mixing of the particles and the melt with larger particles found near the outer edges of the ingots. Variations on particle size and interaction time between the inoculants and the melt resulted in the Ti-Ta inoculant reducing the as-cast equiaxed grain size by a factor of two compared to non-inoculated samples as well as increasing the equiaxed fraction in the ingot.INTRODUCTION Lightweight metals are of particular interest in aerospace applications. The hot sections of turbines are dominated by blades made of nickel based superalloys. Recently the GEnx turbine introduced TiAl blades in the last low pressure stage of the turbine to reduce weight and improve fuel efficiency (Kim & Dimiduk, 1991). In order to carry these benefits deeper into the turbine the high temperature (>800oC) properties of the alloys must be improved. Current grain refinement methods to improve properties rely on boron additions which may not be applicable for all blades as brittle precipitates may be formed during processing (McCullough, Levi, Mehrabian, & Hyman, 1991). A novel grain refinement process was previously introduced called “isomorphic self-inoculation” using Ti-Al-Nb particles to successfully grain refine TiAl (Kennedy, Zollinger, Bouzy, & Daloz, 2016). In order to better understand the mechanism of this process an investigation was carried out using the same process but with a Ti-Ta alloy which is more stable in the TiAl melt than the Ti-Al-Nb."

Jan 1, 2017

By Joseph C. Gillen

This paper discusses the design, construction, and performance of the support of excavation system used at The Atlantic Building jobsite. The support of excavation system had to be adaptable to the different conditions surrounding the site. These conditions included support of four historic building façades, including the nine-story Atlantic Building, as well as support of three historic row-houses along two walls. Directly adjacent to the site is the historic Ford?s Theatre and townhouse. Across a 15? alley is the American Immigration Lawyers Association (AILA) Building, and across a 30? alley is the Federal Election Commission Building and another ongoing excavation. Of historical note, these two alleys were the escape route for John Wilkes Booth following his assassination of President Lincoln. With the excavation being 53? to 58? deep, the system included driven and drilled soldier piles, drilled bracket piles, and two modified tangent walls. The bracing included tiebacks, corner braces, wales, cross lot struts, and a specially designed support system for the nine-story façade. The footprint of the excavation included 12 corners and all alleys and streets were to remain open during construction. The performance requirements for system movement at Ford?s Theatre and AILA Building were ½ inches in the horizontal direction. The modified tangent walls were used in these areas to provide stiffness. The soil conditions at the site were fill material on top of a shallow, sandy, silty, gravel layer on top of a deep layer of soft organic silt and clay. Below the silt and clay layer was fine sandy material at the subgrade.

Jan 1, 2006

By Stanley P. Jacobsen

Samples of fine coal refuse were obtained from 11 coal preparation plants throughout the United States. These samples were characterized by ash analysis, particle size, and mineral composition. From the characterization, geographical locations, and the dewatering equipment being used by the plants, five sites were selected for obtaining bulk fine refuse samples. The selected coal preparation plants were using for final dewatering thickeners followed by: a vacuum disc filter, a filter press, a belt press filter, a centrifuge, and a settling pond. None were using thermal drying. The moisture content of the final cake varied from approximately 23% to 50% depending upon the feed material, flocculant addition, and the type of equipment. The filter press gave the lowest moisture content followed by a belt press and then either a centrifuge or vacuum filter. The centrifuge products were all dried to an approximate 5% moisture in a thermal dryer.

Jan 1, 1981

By S. H. Lorain

This paper briefly describes the principal known commercial and near commercial deposits of gold-bearing gravel end the principal placer mining operations of Idaho County, Idaho. It is one of a series of similar papers on western mining districts. The data used in writing this paper were gathered during the summer of 1937. Information concerning gold-bearing gravels was obtained from prospectors and operators, while operators supplied most of the data on mining operations. No attempt was made actually to test the gravels. The principal object of the examination was to indicate placer areas worthy of further investigation by prospective operators.

Jan 1, 1938

By L. D. Tracy

"The first study of this subject has been made in Illinois, but as opportunity affords, similar studies will be made in other States. It is hoped that the data obtained will assist the coal—mining industry to standardise the forms of leases, and so avoid some of the abstruse and ambiguous clauses which may be found in many of then and the consequent liability of costly litigation.In some of the publications of the Illinois Mining Investigations prepared under a cooperative agreement with the U. S. Bureau of Mines, the Illinois State Geological Survey and the Engineering Experiment Station of the University of Illinois, the coal areas of the State have been dividedinto eight geological districts, each district being treated separately.report covers District No. VI of that classification, and it is hopedstudies of the other districts will be completed in the near future and similar results published.The report includes a short description of the geological condition the character and quality of the coal and the nature of the surface, data for which have been taken largely from the Illinois Geological Survey publications.Mining methods and percentages of recovery are mentioned, together physisal conditions, market and transportation facilities, because all of these factors have a bearing on royalties and leasing conditions."

Jan 1, 1926

By Derek T. Novotny

Blasting cap precision is of major importance to advanced blast design. New technologies have introduced the use of microchips within detonator casings in the hope that the electronic control of the timing element will increase the accuracy of the cap and therefore improve the results of perimeter control blasting applications. The electronic detonators have proven to be accurate in timing tests done to date. They boast cap scatter results to microsecond accuracy, but the question is, does this degree of accuracy actually prove to be beneficial during practical use in the industry, or are conventional technologies applicable.

Jan 1, 1998

The United States has not begun commercial operations to tap its largest poten-tial sources of oil supply - oil shale and coal. The reason is that domestic petrol-eum has been plentiful in the past and liquid products probably could be produced from it at the lowest cost. In view of the ever-increasing need for petroleum in the United States, the critical international situation threatening foreign supplies, the growing demands for steel, and the heavy costs to industry of constantly discovering and developing new oil fields, it is believed that the prompt development of a synthetic fuel industry based on oil shale and coal is not only requisite to safeguard our oil supply but is an economically sound course for the foreseeable future. To neglect its development is to close our eyes and minds to our own resources at a time when they are needed critically. It also is apparent now that neither the Government nor industry would be taking any considerable economic risk in starting the initial plants, especially as measured against their potential value in meeting critical oil and chemical demands and in building a new industry in the West.

Jan 1, 1951

By R. F. Chaiken

The Bureau of Mines has conducted a study of mine fires in the Anthracite Region of Pennsylvania to determine the most effective approaches to fire control in this area. The problems involved in controlling an anthracite fire include the geological and mining conditions in this area, the propagation characteristics of anthracite, the fire control methods available, the hazards associated with these fires, and the mar-ginal effectiveness of past fire control projects. From this genecal background, fire control options were discussed as they apply in ISBO to the Centralia mine fire. Probable effectiveness, feasibility, and costs were assessedv The options evaluated include four excavation plans, flooding, hydraulic flushing, water curtain isolation, mining to construct an underground carrier, burnout control, and relocation of the community. The most advantageous from a technical viewpoint is an excavation method combining complete excavation of the fire zone within the borough with trenching to confine the remaining fire. It appears that for many anthracite fires, as for the Centralia mine fire, there are no available control measures that have a moderate cost, are proven effective, and produce minimal disruption on the surface.

Jan 1, 1983

By George J. Tamara

The urban environment presents special challenges for the design and construction of earth retention systems. Complications arising from difficult subsurface conditions are compounded by the presence of urban infrastructure and existing and prior construction. The proximity of adjacent structures as well as intense prior use can cause special concerns including the potential for archeological artifacts or contaminated ground or ground water. Utilities and structures may be particularly vulnerable to the effects of ground movement, dewatering and vibrations. Difficulty of access, congestion and limited work areas may severely restrict means and methods of construction. Dewatering may be limited or prohibited because of concerns for disposal of clean or contaminated water, depletion of aquifers, drawing of contaminants to the site or dewatering induced settlements.

Jan 1, 2003

By Keith A. Heasley, Frank E. Chase, Christopher Mark

Deep cover retreat mining (overburden in excess of 750 ft) is an important emerging issue which will intensify in the future as the more easily mined shallow seam reserves are depleted. Analysis of Mine Safety and Health Administration (MSHA) statistics indicates that deep cover pillar recovery accounts for a disproportionate share of the underground coal mine roof/rib fall fatalities and injuries. Past research has shown that previously recommended Analysis of Retreat Mining Pillar Stability (ARMPS) stability factors (SF’s) may be excessive for deep cover pillar design. The objectives of this study were to evaluate the various methods and strategies by which panels, production pillars and barrier pillars are developed and extracted under deep cover, and to develop appropriate design guidelines. In the course of the research, 29 mines in 7 states were investigated to collect panel design case histories. At each mine site, underground geotechnical data were collected on the pillar line in order to document roof rock, coalbed and floor conditions. The analyses indicated that squeezes were the most likely failure mode where the depth was less than 1,250 ft, but bumps predominated in the deeper cover cases. Immediate roof rock quality, the ARMPS SF’s, and barrier pillar stability factors were all found to be important parameters in determining the outcomes of the case histories. Design guidelines, including suggestions for barrier pillars to isolate active panels from nearby gobs in bump prone ground, are also proposed.

By H. Robert Ensminger

The Belizean economy registered a modest real growth of 1.3% during 1981. The gross domestic product (GDP), based on current prim was $121 million' with an inflation-rate of 10%. The country received $19 million in economic aid during 1981. In early 1981, Belize'e four commercial banks raised the interest on deposits to 15% in an effort to curb capital outflow. During 1981, the financial situation deteriorated somewhat, particularly the balance of payments. For the year the total value of imports exceeded exports by almost $38 million, while the Government continued to maintain a fairly free trade policy. Import duties and term averaged about 8% on essential item and 40% on nonessential ones.

Jan 1, 1983

By F. A. Rutledge, B. S. Webber, J. M. Moss

"INTRODUCTION The United States, with its vast resources of relatively low-grade zinc been the world's leading producer of zinc -metal for many years. The expanded zinc production during the period, 1939-44, inclusive, was induced by favorable premium prices and has depleted the known ore reserves in the United States. The 1943-44 rate of zinc production cannot long be maintained in the United States, especially if premium prices are removed. Domestic zinc reserves, have been depleted to such an extent that it is doubtful if our mines will again be able to completely and continually fulfill the needs of this country.The Bureau of Mines, anticipating a postwar consumer demand for 550,000 to 750,000 tons of slab zinc and an additional 100,000 tons for use in paints and chemicals, sent two engineers to Sedanka Island in July 1945 to investi¬gate the deposits near Biorka Harbor.ACKNOWLEDGMENTIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion the Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Nov 1, 1946

By Peter Murphy

This report (arid related appendices) provides a description of the functional design specifications, engineering design specifications, and program of instruction for development of a training system for dragline equipment operators. Based upon a task analysis and training system analysis prepared under Phase I, Phase II efforts expanded upon and refined the functional design specifications. The training hardware components have been developed to a point shy of system fabrication. A detailed outline of the porgram of instruction and content sequence has been prepared. The objective of the training system described in this report is to provide new operators of dragline equipment with the requisite skills and knowledge to assure cost-effective development and an adequate supply of our human resources.

Jan 1, 1976