Search Documents

By Jamal Rostami, Richard Kastner, Ahmad Ramezanzadeh

Improving the accuracy of the performance prediction models for hard rock Tunnel Boring Machines (TBMs) is important in estimation of the schedule and cost of tunnelling in related projects. The effects of rock mass on performance of TBMs has been studied extensively, yet due to the complex nature of the process, impact of many parameters influencing machine advance rate are not very clear and there is still room for improvements. More accurate estimates can be obtained by better understanding of operating parameters in various geological conditions and can lead to matching machine specifications with job conditions, optimizing machine performance, and avoiding long delays and downtime for increased productivity. This paper will offer review of two case histories including Queens Water tunnel in New York and KCRC project in Hong Kong. The analysis of the available field data, including the geological back mapping and results of laboratory testing of rock mechanical properties, machine operational parameters and achieved rate of penetration will be presented. This includes statistical analysis of available field data to provide a better understanding of the influence of rock mass properties on performance of hard rock TBMs as well as related formulas to improve performance estimates.

Jan 1, 2005

By F. J. Tavera, J. A. Finch

A probe suitable for on-line measurements of gas hold-up in industrial flotation systems has been developed. It is based on an open cell for measurement of slurry-gas conductivity and a novel syphon cell for measurement of slurry-only conductivity. The desired behaviour of the two cells was demonstrated and estimates of gas hold-up were shown to be in good agreement with independent measurements. The gas hold-up probe was used as a diagnostic tool to assess the operation of flotation columns. Differences in gas hold-up between baffled sections in two industrial columns were detected

Jun 18, 1905

By Harold J. Polta

This Bureau of Mines publication considers the feasibility of augmenting the present transportation system by pipelining taconite concentrates from the Mesabi Range to the Chicago area. The cost of pipelining in the hypothetical system using water as the carrier is estimated to be between $3.66 and $3.97 per long ton. This appears competitive with the 1970 rail-vessel transportation rate of $4.08 even after allowing a few cents per ton for barging from the terminal to existing furnaces. Political obstacles requiring solution before such a pipeline could be built and the feasibility of using crude oil as the carrier fluid are also discussed. FORTRAN routines used to calculate unit transportation cost for specific estimated values of cost items and for a range of values are presented. The effect of deviations from estimated values of cost items on the total unit transportation cost are shown graphically.

Jan 1, 1971

The distribution of chrome spinels in a magnetically fractionated ilmenite concentrate sourced from the Murray Basin was characterized by XRF assaying, quantitative electron microprobeanalysis, grain mapping, automated mineral phase clustering, and modal analysis. At least 14 distinct chrome spinel types were present in the concentrate. There is considerable variation in the amount of each chrome spinel type present, although a high-Mg, high-Al phase makes up close to 45 per cent of the total spinel population. Magnetic fractionation results showed significant variation in the composition and relative abundance of spinels reporting to each fraction. Low magnetic field strength fractions (ie. high susceptibility grains) were dominated by chrome spinels that are mid-range in Al and Cr. These spinels have the highest magnetite, ulvospinel and Fe(Al,Cr)2O4components. In comparison, the high field strength fractions (i.e. low susceptibility grains) have the majority of the grains with high-Al contents indicating a higher proportion of Mg(Al,Cr)2O4component. Spinels high in a (Al,Cr)2.67O4non-stoichiometriccomponent are absent at low field strengths but tend to be concentrated in the high field strength, non-magnetic fractions. Intermediate field strength fractions tend to exhibit a broad spread in spinel compositional types. A mild roast treatment of the sample had no clear effect on the distribution of chrome spinels between different magnetic fractions, but it did cause a change in the magnetic properties of the accompanying ilmenite grains. The effect of more extreme roasting conditions on the magnetic properties of the chrome spinels is to be determined.

Jan 1, 2003

By James A. Finch

"I offer a personal view of what the next 30 years holds for mineral processing. Re-stating that mineral processing will remain a vibrant industry in raw material production, growth opportunities in waste management are identified. The processing sequence familiar now (mining -mineral processing -extraction) will become more interwoven. In situ processing (i.e., milling underground) will evolve from concept to demonstration. Opportunities to exploit physical properties altered in chemical (pyro-and hydro-) processing will present themselves. In primary grinding, the path to AG/SAG milling will progress with little deviation but opportunities in regrinding are wide open. Flotation will see the trend to designing bubble/particle reactors accelerate simultaneously with a vigorous response from mechanical cell suppliers. Gravity separation remains a bastion of the lone inventor but I anticipate that the new lines will come from the waste management business. I finish by examining the ""research cycle"", identifying growth in small ""high tech"" companies and university research centres.IntroductionI have been asked to offer a personal view of""where we are going in mineral processing?"". Gazing into crystal balls is quite a cottage industry as we approach the end of the millennium. Academics are often asked to assume the role of visionary, I presume because it is considered in their mandate, to reflect and philosophize (or, less charitably, because they are considered to have the time). Since this is the 30th Annual Canadian Mineral Processors Operators Conference, I am tempted to suggest the next 30 years as my frame of reference. This is about equivalent to one engineer's career or, given it takes typically 15 years to go from concept to realization in mineral process engineering (Napier-Munn, l 997a), about 2 ""invention cycles"". With this length of cycle, much that is familiar now will remain so over the 30 years.Research and development (R&D) is in response to need. The overarching need in mining is to find new ore bodies. Process developments cannot compensate for a depleting deposit or a declining commodity price. Mineral processing R&D is characterized by incremental gains, aimed at pushing the mine down the cost per tonne league table. Breakthroughs are the exception (flotation at the turn of the century was one). This must be kept in mind when trying to predict the future in our business."

Jan 1, 1998

By M. S. Klima, A. P. Pinkerton

Solid-bowl (decanter) centrifuges are used extensively to dewater slurries in a wide range of industries. However, the application of decanters as classification devices is not as common. In this study, the performance of a continuous, pilot-scale, solid-bowl centrifuge was evaluated when classifying an ultrafine coal slurry containing nearly 60% material less than 10µm. The current study examined the effects of operating conditions on centrifuge performance. The test conditions included centrifuge bowl and scroll speeds, volumetric feed rates, solids concentration, and pond depth. Centrifuge performance was evaluated using partition curves, along with product yields and solids concentrations.

Jan 1, 2000

By M. A. Elliott, H. H. Schrenk, L. G. Berger, John C. Holtz

"INTRODUCTION Interest in the possibility of using Diesel 6/ engines for haulage power in mining and tunneling is increasing in the United States, owing largely to the reported successful use of Diesel locomotives in European coal mines and to the comparatively recent development of automotive Diesel engines in this country. The extent of this interest has been evidenced to the Bureau of Mines by numerous requests for information as to the factors that must be considered if Diesel engines are to be used safely underground.Proponents of the application of the Diesel engine to underground haulage base their claims for its safety upon a comparison with the gasoline engine, assuming that (1) the carbon monoxide content of Diesel exhaust gas is always low and that (2) fire and explosion hazards from Diesel fuel are minimized because of its low volatility. In these respects the Diesel engine appears less hazardous than the gasoline engine, whose use underground has been discouraged by the Bureau of Mines and other organizations interested in safety in mining. However, such generalizations cannot be accepted as conclusive evidence that safety is inherent in Diesel engines in underground service, as European experience indicates that certain hazards may accompany their use. Such hazards were discussed in a previous publication 7/ that reviews developments in the use of Diesel locomotives in European coal mines.The Bureau of Mines has initiated a study of the hazards that may attend the use of Diesel engines underground to obtain first-hand information that may serve as a basis for recommending sale practices under conditions existing in the United States."

May 1, 1940

By Ronald T. Mayerle

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 20,500-acre part of the 104,085-acre Rincon Wilderness Study Area (OR-002-082) in order to evaluate its identified mineral resources. The wilderness study area is located in Harney County, OR, about 12 miles west from Fields. No mineral resources were identified within the study area. A literature search found no records of mining or minerals exploration, nor did a ground search find any evidence of mining-related activity. Of seven alluvial samples taken from the major drainages of the study area, all were barren except one. This sample, taken from a dry streambed along the southern boundary, contained $0.07 gold per cubic yard; however, this small amount of gold is of no economic significance, and the source is probably outside the study area. The Pueblo-Steens mining district extends to within 4 miles east of the study area. No evidence of geological environments similar to those that were responsible for the formation of resources or occurrences of metals and nonmetals within the district is known within the study area.

Jan 1, 1987

By J S-L Chan

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Cu-Ag-Au mineralisation at Kluwih prospect in Eastern Java, Indonesia is related to a high-sulfidation hydrothermal system within a volcanic dome (2.35 × 1.7 km diameter). The mineralisation occurs mainly in steeply dipping, structurally-controlled quartz-enargite-pyrite veins (several centimetres to 2 m wide) and is hosted mainly in porphyritic dacite, volcaniclastic rocks and volcanic breccia of the dome and in an underlying andesite that yielded a zircon U-Pb age of 11.5 Ma.Short wave infrared spectrometer analyses were carried out for alteration mapping at Kluwih. There are two main stages of alteration produced by the hydrothermal activity. The alteration mineral assemblages indicate an advanced argillic alteration. The Cu mineralisation occurred in the form of enargite and subordinate chalcopyrite with an intergrown texture in the early stage. These mineralised veins are characterised by narrow pyrophyllite ± diaspore and dickite selvages (metres wide) and a peripheral K-muscovite envelope (sericitic alteration) up to 100 m wide. The K-muscovite envelope is zoned outward to Na-muscovite or Na-illite. Late-stage kaolinite and smectite alteration overprints the porphyritic dacite and may obscure the nature of early mica-clay alteration. The spatial distribution of different alteration assemblages suggests that the temperature of hydrothermal fluid increases with depth.Both the high-sulfidation mineralisation and advanced argillic alteration are suggested to be related to magmatic-hydrothermal fluids, which are likely to originate from an undiscovered deeper porphyry Cu-Au system below the porphyritic dacite. Based on alteration mapping results and comparisons to similar deposits, the porphyry intrusion could be up to 500 m below the volcanic dome. Further geochemical and mineralogical studies may help to target the potential underlying porphyry system.CITATION:Chan, J S-L, 2015. High-sulfidation epithermal Cu-Ag-Au deposit, Kluwih, eastern Java, Indonesia – alteration and implications for potential porphyry cu mineralisation, in Proceedings PACRIM 2015 Congress, pp 213–218 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By D. W. Bridges

Solvent extraction has become important in recent years as a unit process in extractive metallurgy. The flexibility and simplicity of the technique have attracted widespread attention, and numerous papers describing actual and projected metallurgical applications have been published. However, differences in terminology, procedure, objectives, and standards, as reflected in reports by different operators and investigators, have sometimes made appraisals and comparisons difficult. Consequently, a need appeared for n series of basic reports on the subject. This Bureau of Mines Information Circular is the first of such a series. It deals with the status of solvent extraction in metallurgy, as well as with the rudiments and terminology of the unit operation. In analytical chemistry, extraction of molecular species from aqueous media by immiscible organic solvents has been used for many years to separate and determine chemical elements (61).4 Complex chlorides of iron and other metals are readily soluble in ethers and ketones, as are the nitrates of uranium and thorium. Most metals are extractable as complex salts of some organic reagent, such as dithizone, 8-hydroxyquinoline, or cupferron.

Jan 1, 1962

By L. Holappa

Ferroalloys like FeCr and FeMn are mostly produced in submerged electric arc furnaces. Typical for these processes is that the amount of slag is quite high. The role of slag for the process is thus very essential and specific chemical, physical and electrical properties are required. Slags in FeCr process are Al2O3-MgO-SiO2based with minor contents of CaO and CrOx. Slags in FeMn process are principally similar originating from silicate minerals but can have quite a large composition range depending on the manganese ore and its gangue minerals. Characteristic for FeMn process is that the slag is rich in manganese oxide up to above 30%. A common feature is that the ?ore oxides?, CrOx and MnOxin slag are not only divalent oxides but also containing some higher valent of Cr3+ and Mn3+, respectively. In FeMn production conditions the slag consists mainlyMn2+. This is a clear difference from CrOx containing slags in which both two and three valent coexists in slags in FeCr process conditions. Oxidation state of the slag depends on the ambient oxygen partial pressure and temperature in the examined process. Thermodynamics of slags in ferroalloys production are discussed in terms of phase diagrams, activities and oxidation state of chromium and manganese oxides. Further, slag properties influencing reduction kinetics and furnace operation i.e. viscosity and electrical resistivity are discussed. Keywords: review, slags, ferroalloys, ferrochromium, ferromanganese, thermodynamics, physical properties.

Jan 1, 2004

By J. S. Kennedy, R. G. Omeara

Beryllium is a strategic metal of ever-increasing peacetime importance because of the unusual properties of beryllium-copper alloys. These unusual characteristics are the combination of high strength and hardness, high fatigue resistance, and high wear resistance in alloys that have the corrosion resistance of copper. The principal industrial source of beryllium is the mineral beryl, a beryllium-aluminum silicate that occurs in pegmatites associated with quartz, feldspar, mica, and smaller amounts of various accessory minerals. The beryl is usually recovered in processing the pegmatites for the recovery of some of the other mineral constituents. Pegmatite deposits are found in various parts of the United States, but those in the Black Hills of South Dakota are the source of most of domestic production. The beryl marketed from the South Dakota pegmatite deposits occurs as coarse crystals, which are obtained by hand sorting. These pegmatites also contain other valuable minerals.

Jan 1, 1948

By Steven K. Ruggieri

This report describes the use of the sprayfan auxiliary ventilation system for methane and dust control on continuous miner sections to potential users. The sprayfan auxiliary ventilation system is a modified water spray system which directs intake air to and across the front of a continuous miner to prevent build up of methane gas and dust concentrations. This user's manual contains practical information concerning sprayfan: a. Description and capabilities b. Design c. Installation d. Operation e. Maintenance. Underground tests, independent laboratory tests, tests by MSHA, and independent installations by coal producers have confirmed the performance of the sprayfan system. There are currently 150 sprayfan systems in operation in underground coal mines.

Jan 1, 1981

By L. C. IlsLey, E. J. Gleim

Electrical apparatus because of its flexibility and its adaptability to all classes of service has become essential to the mining industry. Hence the problem of providing electrical equipment that is safe for use in explosive mixtures of methane and air is of prime importance in coal mining. Ilwestigatorsand experiment stations early recognized this fact and much work has been done in the investigation and the development of electrical apparatus for use in atmospheres containing fire damp. The term "fire damp" as applied throughout this bulletin means an explosive mixture of methane and air. Direct-current motors and alternating-current motors of the slipring type when running usually give off electric arcs or flashes that will ignite fire damp. Other 'motors that ha,'e no moving electric contacts may become dangerous through accident, deterioration, or neglect. Auxiliary apparatus such as fuses, switches, rheostats, and controllers may arc, flash, or become heated to snch a degree that fire damp can be ignited. Such equipment is still more dangerous when worn or out of repair. In the United States the development of apparatus for use in gaseous mines has been associated largely with coal-cutting equipment run by electricity. This is undoubtedly due to the use of such equipment at the face of the mine workings, where the chance of igniting fire damp is necessarily greatest. One American manufacturer built a coal-cutting equipment of the totally inclosed type for use in firo damp atmospheres in 1903. Another built similar equipment with special protective devices in 1906, for export. During the years 1910 and 1911, the Bureau of Mines at its Pittsburgh experiment station conducted a preliminary investigation of the safety of such protection as was then in use or under consideration. Five motors were submitted for this investigation, each having somewhat different methods of protection. The results of this investigation were published in Bulletin No. 4G.a

Jan 1, 1920

By D R. Anstey

The growing demand for iron ore from Western Australia has led to an increased focus on the development of magnetite and lower grade iron ore deposits. The need to process and beneficiate the ore from these projects can result in the generation of significant quantities of iron ore tailings over the life of a project. Over the coming decades, the management of iron ore tailings will become a significant aspect of the mining landscape in Western Australia.The tailings generated from iron ore projects differ signifi cantly from other mineral tailings currently produced in Western Australia. Iron ore tailings are generated on a scale not matched by any other mineral process and can often contain asbestiform or potentially acid forming components. New iron ore projects are coming under increased environmental scrutiny because of their large scale operations and the sensitive environments in which they occur. This combination of factors creates some unique challenges for the management of tailings generated by iron ore mining in Western Australia.This paper presents the fi ndings of two studies conducted in recent years to overcome the challenges posed by iron ore tailings. The paper discusses the role of laboratory testing in the development of management strategies for asbestiform minerals in tailings. It also presents a numerical modelling approach for evaluating the rates of rise in the storage of magnetite tailings. The paper concludes by outlining how the findings of these studies can be applied to reduce tailings management costs, lower risks and improve environmental outcomes for the management of tailings from iron ore mining.

Jul 11, 2011

By J. T. Jordaan

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree This paper addresses the critical parameters that need to be considered when designing a mechanized bord-and-pillar mining layout for a narrow tabular steep dipping orebody. These parameters are : ?Reef dip ?Reef width ?Geological structures within the orebody ?Physical dimensions of the selection of machines ?Gradeability of the selection of machines. The main objective in designing such a layout is to maximize machine efficiencies whilst minimizing dilution. This methodology was then applied in the design of a mechanized bord-and-pillar mining layout for a given piece of ground (Vlakpoort and Moddergat) using a given selection of machines. This piece of ground contains the PGM bearing UG2 Reef with an average thickness of 124 cm and dipping at 18°withadverse strike and dip changes. Two bord-and-pillar layouts were designed for this area. Layout 1 is characterized by the use of strike conveyors to convey ore on strike with an average LHD hauling distance of 35 m. Layout2 uses LHDs for all on strike conveyance of ore with an average hauling distance of 75 m. These two layouts were then technically and financially compared. It was concluded that layout 1 is theoretically superior but layout 2 was chosen due to its greater flexibility and probability of operational success. Layout 2 was also compared to conventional mining and it was concluded to be more economically feasible. However the latter is a proven mining method in these conditions and has a lower risk operational failure. Bord-and-pillar mining has some favourable promises such as improving labour difficulties, lowering operating costs and providing safer working conditions. The success of mechanized bord-and-pillar mining in narrow tabular steep dipping orebodies will depend on the extent of the research and development efforts which need to create and innovate technologies to overcome some of the current limitations stated in the above-mentioned parameters.

Jan 1, 2003

By K. J. Bathe

The current version of the computer program ADINA/BM (Automatic Dynamic Incremental Nonlinear Analysis for the Bureau of Mines) for linear and nonlinear, static and dynamic finite element analysis of mine structures is described. The complete report is divided into four parts. In Part A the program solution capabilities, the finite element library, the logical construction of the program and storage allocations are discussed. In Part B the theory and numerical techniques used in the program are summarized. In Part C brief problem descriptions and solution results for some sample solutions that have been transmitted as data cases with the program are presented. In the last section of the report, Part D, the users? manual of the program is presented. Program ADINA/BM is a general effective tool for coal mine structural analysis. The program is an extension of the computer program NON SAP (which was developed under an earlier contract with the U.S. Bureau of Mines). The important additional capabilities of ADINA/BM are: (1) the occurrence of all elements is time dependent, (2) all elements can be used in geometric and material nonlinear analysis, (3) the truss element can be used in elastic-plastic analysis, (4) the three-dimensional element can be employed in orthotropic, elastic-plastic and cracking and crushing analysis, (5) the program executes an out-of-core solution and thus allows the analysis of very large and complex coal mine models, (6) the truss elements can be employed as 2-4 variable-number-nodes elements, (7) a rock material model has been implemented, (8) displacement constraint equations can be imposed in the solution, (9) more flexibility in specifying the incremental solution strategy and an acceleration procedure in the equilibrium iteration are available

Jan 1, 1978

By Fred S. Karn

Inhibitors are used in coal mines as a precaution against accidental dust explosions. Although rock dust is the usual inhibitor many others have been tested. To facilitate testing a screening process using laser irradiation was proposed. The procedure includes irradiation of a coal-dust mixture followed by mass-spectrometric analysis of the evolved gases and an evaluation of the flammability characteristics of the gases. Carbonate-type inhibitors decreased the percentage of combustibles in the gases generated and inhibitors like NaCI (thermally stable salts) decreased the total gas generated. A suitable test procedure did not result from the investigation, demonstrating the inadequacy of fast heating, non-combustive techniques in rating inhibitors of coal dust explosions.

Jan 1, 1973

By Polysius AG

"The Lone Tree demonstration was an important milestone in bringing High Pressure Grinding Roll (HPGR) technology into hard rock applications in the mining industry. HPGRs have become standard equipment in the cement, iron ore, and diamond industries over the past fifteen years, but their use in severe duties found in the hard rock mining sector has been restricted due to high roll wear and subsequent low availability. HPGR availability has historically been limited because of frequent downtime for edge weld rebuilding as the rolls wore and short tyre life from high roll surface wear rates.Recent advancements in HPGR wear protection are now being evaluated for commercial applications in the gold and copper mining industry where this technology may offer benefits in comminuting hard and/or abrasive ores and in improving metal recovery in heap leaching applications.Proving the feasibility of HPGRs for processing competent, abrasive gold ore, Newmont Mining Corporation, the world's largest gold producer, operated an HPGR demonstration plant employing a POLYSIUS (POLYCOM) HPGR incorporating some unique wear protection, at their Lone Tree gold mine near Winnemucca, Nevada. Results of the successful demonstration are presented and evaluated in this paper.The Lone Tree HPGR demonstration plant operated for three months, from April through June 2003. The HPGR operated for 1626 hours and processed 141,000 tons of ore. This technology demonstration focused on measuring operating performance, wear characteristics, and availability of today's HPGR technology.Polysius' innovative roll surface wear protection system eliminated edge-welding downtime. Improved surface wear protection extended tyre life to predicted durations acceptable for very abrasive service. The POLYCOM HPGR is now deemed suitable for selected hard rock applications."

Jan 1, 2005

By N. Sano

The chromium oxide in stainless steel slags usually exists as Cr2O3. However, there is a possibility that it is oxidized to hazardous CrO3 after disposal or during use. Therefore, some technical developments to reduce chromium oxide by using a smelting reduction technique have been reported recently. This paper describes the fundamentals of the technique which have been applied to ferrochromium production and reviews the recent results in literature.

Jan 1, 2004