Search Documents

By M. Z. A. Bakar

A series of full scale laboratory linear rock cutting tests was carried out with a long bladed single disc cutter (292 mm diameter, 11mm wide constant cross-section blade) on dry and water saturated sandstone blocks using a linear rock cutting machine (LRCM). The muck collected from the cutting tests has been analyzed to establish a link with the specific energy (SE) of the operation. Coarseness index (CI), a non dimensional parameter, has been found to be a useful indicator of the relative efficiency of the cutting operation. An inverse relationship of the form SE = k CI-n is observed between SE and CI with very high CI usually corresponding with the lowest values of SE. The power n of the relationship for both dry and saturated rock tests is much less than the values found in the previous studies using constant cross section disc cutters and is believed to be dependent on the strength of the rock and the cutter type used. Although the average CI is found to be lower for saturated rock than for dry rock, at the same time saturated rock cutting is found to be less energy intensive (in terms of SE) than dry rock cutting. Moderate correlation exists between the production rate or yield and the SE of the cutting operation for both dry and saturated rock, which can provide some useful information about the field production rate discounting the effect of discontinuities in the rock mass.

Jan 1, 2012

By Emöke Imre

A point-symmetrical linear coupled consolidation model with displacement boundary condition is suggested for the description of the consolidation around the pile tip after pile penetration. Analytical solution is given. Main features of the solutions are predicted by the analysis of the system of differential equations and, the boundary conditions.

Jan 1, 2002

By Robert W. Van Dolah

On December 27, 1961, a fire and explosion destroyed the blasting agent mixing plant and an attached storage barn of the Whitaker-Atlas Supply Co., near Norton, Wise County, Va. Five residences, an office building, four trucks, and three automobiles were completely destroyed; a house trailer and several other trucks and automobiles were severely damaged; and other property damage, including much window breakage, occurred up to 3 miles or more airline distance away. Through the quick action of the fire marshal of the Norton Fire Department, Norton, Va., there were no fatalities and only five persons required hospitalization. This incident is of particular interest because of the widespread practice of mixing fuel oil (FO) with ammonium nitrate (AN) to prepare low-cost blasting agents, in many cases under conditions and circumstances not very different from those presented here. A representative of the Bureau of Mines Explosives Research Laboratory, Pittsburgh, Pa., and field representatives of the Bureau's Health and Safety Activities conducted the investigation. Information in this report was obtained from representatives of the Whitaker-Atlas Supply Co., the Norton fire marshal, and others who were on the scene either shortly before or after the incident occurred. Representatives of the Manufacturing Chemists' Association, the Institute of Makers of Explosives, and individual ammonium nitrate producers participated in the inquiries and investigations.

Jan 1, 1962

By David J. Kusler

This Bureau of Mines study is an appraisal of the demand for platinum, should this strategic metal be used as a. catalyst in the National abatement of automobile exhaust pollution. The Clean Air Act 0f 1970, as amended, requires that automobiles produced in 1975 and thereafter be provided with antipollutive measures to control automotive exhaust emissions. The study considers the need for automobile pollution control, the methodology for such control, the annual primary (new) platinum demand for automobiles produced from 1975 to 1990, primary platinum availability, and supply-demand forecasts and outlook. The correlative demand for platinum for the production of the required unleaded gasoline is also considered. Methodology for the study included a forecast of new automobile production from 1975 to 1990, development of automobile survival and retirement data, estimates of new platinum demand under various conditions of salvage, and data on recycling the precious metal from the catalytic converters of scrapped vehicles and existing vehicles when their spent converters are exchanged for replacement units. The new platinum demand for automobile exhaust converters, based on a converter service life of 50,000 miles, is estimated to be 1.41 million troy ounces initially in 1975, rising to 1.68 million in 1980, and declining curvi-linearly to 0.94 million in 1990. The platinum demand for converter longevities other than 50,000 miles can be derived from the tabular data presented. An appendix to the report presents a comparison between longevities of 50,000 miles and 25,000 miles. The petroleum industry's demand for new platinum for the production of lead-free gasolines could total as high as 1 million troy ounces between 1972 and 1981, just for expansion of isomerization and reforming capacity, and is in addition to normal operating demand for this metal.

Jan 1, 1972

By Sidney Katell

This study estimates capital investment, operating costs, and selling prices for four underground bituminous mines producing coal with annual production ranging from 1.06 to 4.99 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment ranges from $20,799,800 for the 1 .06- million-ton-per-year (MM tpy) mine to $84,027,500 for the 4.99-MM-tpy mine. Total capital investment ranges from $32,506,800 to $1 22,983,500 for the same mines. Corresponding selling prices for the coal range from $12.87 to $11.64 per ton, assuming a 15-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1976

By Deborah McCombe

-Canadian Regulators -Qualified Person -Professional Association -Resources & Reserves -Foreign Codes -Disclosure of Historical Resources -Issues in Application of Resources & Reserves -Industry Best Practices developed by CIM -Technical Report and Reserves and Resources -Summary

Jan 1, 2003

By Rongdong Deng

A tower-like magnetic system comprising eight permanent magnets was installed at the center of a flotation column to separate chalcopyrite and pyrrhotite minerals. A cyclonic flotation was installed within the underpart of the column to separate the pyrrhotite from the gangues. A three-product magnetic flotation column was fabricated to create a magnetic field and a cyclonic zone. The products were Cu concentrates, pyrrhotite concentrates and tailings. The theoretical magnetic field strengths and the magnetic forces were calculated. The results of the flotation experiments showed that the Cu grade increased from 14.20% without the magnetic field to 26.40% in the presence of the magnetic field and that the S grade in the pyrrhotite concentrates increased in the presence of cyclonic flotation. The separation efficiency of this magnetic flotation column was evident. Therefore, this three-product magnetic flotation column may have a potential application, due to its high separation efficiency.

By Nino Catalano

The combination of two top levels of cross-lot braces designed and installed to act as a truss, and vertical post-tensioning of the panels allow the unbraced excavation of a 36' span. Philosophy of Excavation Support System The excavation of interest is for the cut-and-cover box sections of the southern approach to the Third Harbor Tunnel, which is part of the Central Artery/Tunnel project in Boston, Massachusetts. The 60' deep excavation is located very close to an existing building which is supported by piles, as shown in Figure 1. Therefore, it was necessary to minimize ground movement which may damage the building.

Jan 1, 1994

By Gerald T. Homce

A system capable of monitoring mine electrical power systems and detecting impending component failure could significantly improve power system safety and reduce unscheduled equipment downtime. Such monitoring would require a method of evaluating electrical parameters, calculated from terminal values, for indications of component deterioration. The U.S. Bureau of Mines has targeted electrical failure of squirrel cage induction motors and examined the use of mathematical models to aid in this evaluation. The initial stage of this work is complete, and has produced polynomial networks called adaptive learning networks (ALN's) that can detect and quantify winding insulation leakage simulated on laboratory motors. In this modeling process, empirical data from laboratory motors were used to select the electrical parameters most significant for assessing motor conditions, and mathematical expressions relating these parameters to simulated deterioration were formed. ALN's developed thus far can process readily measured motor terminal information and quantify power and current levels of laboratory-simulated leakage to within 1% and 3% of full load values, respectively, for motors in the 10- to 150-hp size range. The next stage of this research is validation of these ALN's for actual motor failures; this stage is currently underway, using accelerated life testing of laboratory motors.

Jan 1, 1993

By W. G. Pariseau

This Bureau of Mines report is an evaluation of the state of knowledge about gravity flow from bin hoppers, the most commonly used method of handling bulk materials where the force of gravity is used. The requirements for flow to be initiated and to continue, formulas developed experimentally or mathematically from various assumptions to describe the materials flow, and the question of whether or not a material will flow over the entire cross sectional area of the bin hopper according to the flow regime developed are the primary areas discussed. The work of A. W. Jenike, whose pioneering investigations raised bin hop- per design from the trial and error state, is examined in depth and its limitations and assumptions are pointed out. Bin hopper design depends heavily upon prior experience, and suggestions for further studies of bin hopper flow to include the effects of feeders are made.

Jan 1, 1972

By Charles C. Boley

High-volatile A bituminous coal from the Allen mine, Las Animas County, Colo., blended with char produced from the same coal yielded accept-able metallurgical coke in a 500-lb movable-wall test oven. Nineteen experimental runs were carried out using several concentration levels of two different chars, 5.6 and 19.6 percent volatile matter, produced by entrainment carbonization of the base coal. With the higher-volatile char, an acceptable coke was produced at a 22.5-percent concentration; the lower-volatile char did not produce an acceptable coke at the concentrations investigated.

Jan 1, 1972

By G. J. Hearn

between particles in the classifying region is then

Apr 1, 1995

By Grant C. Lukey, Jannie S. J. van Deventer

"The environmental effects of the mining and mineral industry include destruction of natural habitats, changes in river regimes and water tables, and other serious ecological impacts. In this century, it is likely that water will become a critical resource, and in most countries the mining industry competes for a share of this resource. The Kyoto Protocol may at first seem only relevant to the coal mining and power industry, however, it should not be forgotten that the mining and mineral industry is a significant consumer of power. Therefore the ratification of the Kyoto Protocol by most developed countries and the introduction of a carbon credit trading scheme will impact on the industry by potentially increased costs in utilities and waste discharges. It is clear therefore that the mining industry faces many challenges in the coming years. The mining industry?s commitment to sustainable development needs to continue to evolve, in order to meet these challenges effectively. With the advent of globalisation of the industry, it is now an opportune time for the industry to gain international agreement on how they want the industry to achieve sustainability in future years; such a progressive approach is necessary, otherwise government will force the industry to change, which may not necessarily be the best outcome for the industry.INTRODUCTIONThe Earth Summit in Rio de Janeiro in 1992 was an opportunity for world leaders to assemble and discuss strategies and initiatives that provide for further industrial growth without adverse effects on the environment. The World Summit on Sustainable Development held last year in Johannesburg, South Africa, was an opportunity to evaluate those initiatives implemented over the past 10 years, and to set a new and sustainable direction for the future. It is clear that industrial and technology development will continue at a rapid pace in order to serve the needs of a growing world population, but it is essential that the course of this development is well planned, well executed, and that it is sustainable. In reality, while government officials and politicians continue to debate policy and international protocols, the environment continues to suffer and the effects of climate change and global-warming become more real each day."

Jan 1, 2003

By T. A. Henrie

One objective of Project Gnome is to study the feasibility of a phase of the Plowshare program recovering thermal energy from an underground nuclear explosion. The test will be conducted in an underground salt deposit. It is anticipated that some of the energy thus released will be stored as thermal energy in molten salt. This report describes the pre-Gnome experiments conducted at the Federal Bureau of Mines Metallurgy Research Laboratory, Boulder City, Nev. The objectives of this study were to determine the problems involved in the recovery of thermal energy from molten salts to assist in planning the experimental program for the Gnome project.

Jan 1, 1961

By Leena Korkiala-Tanttu, Noora Lindroos, Juha Forsman

"Construction works at the Helsinki city sea shoreline requires dredging and handling of contaminated sediments. Most of these soft dredged sediments are regarded as too poor quality material for earth construction purposes. Mass stabilization technology has been applied to improve the technical and environmental properties of the dredged sediment in order to utilize the material in construction. The treatment site presented in this article is placed in the West Harbor where the dredged sediments are disposed in basins, mixed with binders by mass stabilization and transported to utilization sites. The volume of these basins is about 90 000 m3. So far these basins have been used three times during the years 2011-2014. The most applied binder has been cement. Its high price and carbon footprint have encouraged use alternative binders. Other used binder materials include fly ash and end product of desulphurization from coal combustion, and fly ash from combustion of Estonian oil shale. The technical and environmental properties of stabilized sediments have been studies in the laboratory and in situ thoroughly. Some properties of the stabilized sediments which have been studied are: compression strength, modulus, hydraulic conductivity, leaching of contaminants, etc. The leaching test results show that heavy metal leaching is very low with all binder materials tested.1. INTRODUCTIONContaminated marine sedimentsMarine sediments in the coastal areas are often contaminated as a consequence of industrial and port activities, as well as the influence of cities located there. Construction activities and reclamation of shore line require dredging and handling of contaminated sediments since the level of contamination inhibit dumping of dredged sediments into the sea. Based on their technical properties, most of these dredged soft and watery sediments (clay, gyttja, etc.) are regarded as too poor quality material for earth construction purposes. Economic, sustainable and environmentally safe management of contaminated, dredged sediments is a key issue in many construction sites.In the City of Helsinki, mass stabilization technology has been applied to improve the technical properties of the dredged sediments in order to utilize the material in construction. Owing to stabilization / deep mixing / solidification, also the contamination is encapsulated in a monolithic solid of a high structural integrity. Thus, contaminants migration is restricted by the decreased surface area exposed to leaching.The treatment site presented in this article is placed in the West Harbor (a place of Helsinki called Jätkäsaari) where dredged sediments are disposed into stabilization basins, mixed with binders by mass stabilization and then transported to final utilization sites. The location and principle of these basins is presented in Figures 1-4. The overall volume of these four stabilization basins is about 90 000 m3."

Jan 1, 2015

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and the results are described in this report.

Jan 1, 1983

By Donald O. Capstick

The U.S. Bureau of Mines conducted an inventory of the prospects and mineral resources in the Scodies RARE II area (No. 5212) in 1982. No mineral production is recorded from the area, and no mines are being developed. The Scodies RARE II area is comprised primarily of light colored granodiorite with minor inclusions of mafic granitic rocks. Late stage differentiates of magmas resulted in quartz veins and pods. Metasedimentary rocks which have been mineralized in some parts of the Sierra Nevada were not observed within the study area during this investigation but small inclusions have been reported.

Jan 1, 1983

By Shail J. Butani

In 1986 the Bureau of Mines conducted a probability sample survey, Mining Industry Population Survey, to measure such employee characteristics as occupation; principal equipment operated; work location at the mine; present job, present company, and total mining experience; job-related training during the last 2 years; age; sex; race; and education. The population estimates are necessary to properly analyze the Mine Safety and Health Administration (MSHA) injury (includes illness and fatality data) statistics; that is, to compare and contrast injury rates for various subpopulations in order to identify those groups that are exhibiting higher than average injury rates. This report uses the survey's results to characterize the U.S. stone mining workforce from March through September 1986. Similar reports have been published for the metallic, sand and gravel, and nonmetallic mining industries, as well as for the entire metal and nonmetal mining (includes metallic, stone, sand and gravel, and nonmetallic industries) sector and the coal mining sector.

Jan 1, 1988

By Y. He

Early research showed that the separation of particles based upon their density was not possible in steadily rising air streams. The terminal velocities of moving spheres are determined by their aerodynamic characteristics. This prevents particle separation by density in standard air classifiers. Passive pulsing air classifiers have accelerated airflow in certain regions, which achieves density-dominant separation. Numerical simulation of airflow within passive pulsing air classifiers was done to estimate airflow patterns near a damper. Analysis of those results shows the significant acceleration of the airflow above the damper. Laboratory trial separations have shown that passive pulsing classifiers are superior to standard air classifiers. Keywords: pulsing airflow, passive, simulation of airflow models, acceleration effect, density

Jan 1, 2005

By S. L. Gerhard

In the United States the performance characteristics of permissible explosives are controlled by routine tests, which include firing the explosive into a gallery filled with a methane-air mixture. These tests are made by the staff of the Explosives Division of the Bureau of Mines and, are similar, in general, to those employed in other countries. This control has helped to reduce the frequency of accidents involving the ignition of firedamp by explosives but has not clarified the basic causes, of the ignition. To advance this control and to minimize potential hazards further, this fundamental knowledge is needed. Some of the results of recent research on the causes of the ignition are described herein. NATURE OF THE PROBLEM When an explosive ignites firedamp in the gallery tests, the source of the ignition must be one or more of the emissions from the steel borehole. It has been accepted generally that these emissions are (1) particles, (2) the shock wave, and (3) hot gases and flames. Photographs show that the shock wave emerges from the borehole first, followed closely by hot gases. At first the velocities of these are high and approximately equal, but the velocity of the gases decreases more' rapidly than that of the shock wave, and by the time the reactions causing the flame are complete the shock wave travels in an otherwise undisturbed medium. The particles are originally enveloped in the hot gases but some soon begin to break through and eventually out-distance the shock wave. The approximate geometry of these emissions about I millisecond after the shpt is fired is illustrated in figure

Jan 1, 1939