Search Documents

By L. Adler

Two basic cases involved in the design of an opening in bedded rock are: 1) where the beds deflect from each other so as to be separated; and 2) where the beds deflect onto their lower neighbor, loading the latter while reducing their own load. Analysis of case 1 is relatively simple, while the interference of the original deflection curves in case 2 complicates analysis of the latter. Figures and formulae are presented for determination of interference loading in this situation. The design of an opening in bedded rock involves two basic alternatives.1'2 In one case the beds deflect away from each other, so as to be separated from their neighbors; in the other case the beds deflect onto their lower neighbor, loading it, while reducing their own load. This is shown in Fig. 1. The first case lends itself to a simple analysis, since the upper and lower boundaries of each beam remain a free surface. In the latter case, however, due to the interference of original deflection curves, the analysis is more complex. Earlier investigators of this interference problem solved it by making the tacit assumption that this type of loading was uniformly distributed along the beam's length. While there is no intuitive justification for this assumption, its use does lead to an approximate solution. Still, a more exact solution does not require this apparently unrealistic restriction. To achieve initial simplicity, the analysis will at first be limited to a two-bedded sequence, as in Fig. 2. Since both beams have identical end conditions and spans, the original deflections of their center lines are members of the same family of curves, as shown in Fig. 3. Therefore, if interference occurs at one point along their center lines, it will occur at every point. For convenience, the midspan point is that usually examined. Deflection at midspan for a uniformly loaded beam regardless of end conditions is: where c is a constant depending on end conditions; w is the body load and equals yh, lb per ft; y is the specific weight of rock, lb per ft'; L is the span, ft; E is Young's Modulus, lb per ft2; I is moment of inertia (for a rectangular section), I = bh3/12 = h3/12, (ft4); b is the width of beam and equals one; and h is the thickness of beam, ft; or 3U > yB an Substituting the appropriate values into Eq. lb, interference between the two beds can be predicted. Should it occur, the additional loads along the lower boundary of the upper bed and the upper boundary of the lower bed must be determined. From the principle of action and reaction, these added loads are known to be equal and opposite, as indicated in Fig. 4. Since the final deflection curves for both beds are identical (Fig. 3), their successive derivatives of y with respect tox must also be identical. That is:

Jan 1, 1961

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag compositions. The present report deals with the CaF2-Y203 system for which solidus and liquidus temperatures and solid solubilities were determined. The information is presented as the phase diagram. All specimen compositions were blended from high-purity materials and encapsulated in Mo or Pt20Rh prior toheat treatment. Liquidus temperatures were determined by ceramographic examination of heat-treated and quenched specimens. Solidus temperatures were determined by differential thermal analysis and by electron microprobe analysis of quenched specimens. Terminal solid solubilities were derived by parametric methods. The peritectic system was found to be pseudobinary due to the formation of yttrium oxyfluoride at temperatures near the liquidus. The peritectic point occurs at 7 mole pct Y203 and 1,438° ± 5°C. The terminal solid solubility of Y203 in CaF2 decreases from 7 mole pct at 1,438° C to 1 mole pct at 1,100° C, and the solubility of CaF2 in Y203 decreases from 9.5 to 7 mole pct over the same temperature interval.

Jan 1, 1970

By Lijuan Chen

During the detoxification of chromium-containing slag by Achromobacter sp. CH-1, anionic surfactant Sodium Dodecyl Sulphate(SDS) and its mixed systems with different Tween surfactants(Tween 20, Tween 60 and Tween 80) were used to promote the interaction between the bacteria and the chromiumcontaining slag and the rate of acid-soluble Cr( ? ) leached from the slag. The effects were evaluated by the surface tension, the pH of the leaching solution and the leaching rate of total Cr( ? ) from the slag. The results showed that the surfactants systems improved Cr(VI) leaching and its detoxification of chromium-containing slag. The mixed surfactants of SDS combined with Tween surfactant revealed better effectiveness of detoxification than SDS only. When the mass ratio of SDS to Tween 80 was 1:1, the rate of Cr( ? ) leached from the slag increased by 12%.

Jan 1, 2009

By J. Kempken, T. A. Schreiter, R. Degel, H. Schmieden

Keywords: Pyrometallurgy, SMS Demag, Germany, submerged arc furnace, ferro alloys, non-ferrous, FeCr, FeNi, FeMn, copper, cobalt, slag cleaning, PGM, rectangular furnace After a short summary of the SMS Metallurgy part of the SMS group, the paper will focus on Submerged Arc furnace technology. After general aspects of furnace design, the focus will shift to different applications and their specific furnace requirements. Finally, a state-of-the-art design tool as well as a new invention to improve slag-cleaning technology will be featured.

Jan 1, 2006

By D. Z. Mraz, R. S. Jones

Unlike in coal mines where caving methods are used, the subsidence over potash mines in Saskatchewan, Canada, is a function of gradual mining convergence. Because of the presence of high pressure water aquifers over the evaporite salt formations, the mines have to be designed as regionally stable and no caving is allowed. The extracted area converges gradually and the convergence is mainly a function of the extraction and the mining method employed. Consequently, the subsidence rate is very slow and the bridging of the over-lying strata is a considerably more important phenomenon than elsewhere. The paper evaluates a case history of convergence and subsidence in a deep potash mine in Saskatchewan.

Jan 1, 1986

By R. S. Dean, John Gross

"In a preliminary report made a year ago it was shown that certain minerals when subjected to heating with water under high pressure and temperature were shattered upon the sudden release of that pressure. The main feature in which the results of this method differ from those of conventional grinding is in the differential effect obtained. The more metallic minerals, and hence the valuable minerals, are shattered more readily than are the gangue minerals. In other words, explosive shattering is unique among possible methods for comminuting an ore in that it wastes the least energy on the useless part of the ore. Explosive shattering, therefore, offers possibilities as a means for reducing grinding costs, arid it is this potential advantage of the process that makes it worthy of further experimental study. The first part of this paper is devoted to a study of the mechanism of the process; the, second part reports results obtained in toots on a selected list of ores to exhibit some of the advantages of explosive shattering."

Feb 1, 1933

By A. Ansari

Standard depressants used in the selective separation of copper and molybdenum sulfides by flotation pose environmental and health hazards. In this investigation, the floatability of chalcopyrite and molybdenite in the presence of six well-characterized lignosulfonates was studied through Hallimond tube flotation and adsorption tests. The results define the physicochemical conditions (lignosulfonate type and dosage, pH, presence of ions) for possible selective separation of molybdenite from chalcopyrite. Dissolved polyvalent cations, especially calcium, appear to serve as "activators" for lignosulfonate adsorption on both minerals. From this point of view, the use of lime as a pH modifier is not always appropriate for optimum selectivity since high dosages of lime to produce high pH tend to indiscriminately depress both sulfides.

Jan 1, 2006

By O. R. Eckstrand, M. Asif, P. L. Schwann, A. J. Naldrett, R. J. F. Scoates

Paper presented at the IAGOD international symposium on mineralisation related to mafic and ultramafic rocks, held in Orleans, France, 1-3 September 1993. PGE-bearing sulphide mineralisation is contained in the lower 600 m of the Upper Central Layered Zone of the intrusion. There are four regimes with distinctive crystallisation characteristics. PGE content is low, both in bulk rock and in terms of metal in 100% sulphides, in the sulphide-rich cumulates but increases sharply in the sulphide-poor cumulates at the base of regime 1. Increases in regime 2 have no such clear relationship with incoming cumulus sulphides. PGE contents are low throughout regime 3, but regime 4 has sulphides with high PGE content, decreasing rapidly upwards, at the base of many of its cyclic units. The observations are interpreted as indicating that sulphide saturation occurred in the middle of a cyclic unit in regime 1, after which fractional segregation of sulphide caused a systematic decrease in PGE content. The resulting contrast between 40 000 ppb PGE in sulphides below the mineralised zone and less than 1 000 ppb above is of practical importance in exploration for such zones. In regime 2 the magma chamber was open to fresh influxes and PGE content was not so sensitive to sulphide saturation. In many regime 4 units influxes of new magma caused immediate sulphide saturation and PGE depletion, so that PGE-rich cumulates do not underlie PGE-bearing sulphide zones. Theoretical analysis indicates that regime 1-type behaviour is likely to characterise intrusions below the level at which plagioclase has entered as a cumulus phase and regime 4-type behaviour above

Apr 1, 1994

By F. M. Doyle

Metal removal kinetics and metal ion selectivity in ion flotation were studied from a thermodynamic perspective. Surface tension data could be used with the Gibbs adsorption equation to quantitatively predict the metal ion removal kinetics in alkylsulfate-Cu systems. However, surface tensions predicted cation selectivity coefficients in the sodium dodecyl-sulfate (SDS)-Cu-Ca and SDS-Cu-Pb systems rather poorly, although the predicted order of the selectivity (Cu2+<Ca2+<Pb2+) was correct. Another thermodynamic selectivity model, which used the Grahame adsorption equation and a geometrical analysis, predicted cation selectivity coefficients that agreed very well with experimentally measured values.

Jan 1, 2000

By Darrell Gillis

Recent accidents in the United States underground Coal Mines and the on-going carnage in Underground Chinese Coal Mines has shown the danger associated with the lack of communication infrastructures in an underground environment. The US Mine Safety and Health Administration (MSHA) have introduced legislation that states all Underground Coal Mines must have two-way voice and personnel tracking capabilities by 2009. If Coal Mining companies are being forced to deal with this problem Tunneling Companies will not be far behind. This paper will examine current practices and best case technology to deal with these issues.

Jan 1, 2007

Behaviour of Bubble Clusters in a Turbulent Flow

Sep 13, 2010

By J. Moskowitz

Construction of the new JFK International Airport Light Rail System (LRS) began in 1998 with a pre-construction load test program. This $1.2 billion design-build project consists of approximately 13 kilometers of elevated twin rail. The elevated rail system is supported on nearly 500 piers requiring deep foundations. The presence of underlying compressible and liquefiable soils as well as space constraints precluded the use of large spread footings. In the 1980&apos;s the Port Authority undertook extensive testing to evaluate various piles and drilled shafts types. The LRS piling sub-contractor and the Geotechnical Engineer conducted additional tests for this project to identify the most cost effective deep foundation type. Candidate piles types included: Monotube®, Tapertube®, and closed ended pipe piles. The tapered pile types were found to be the most cost effective and the project utilized both the Monotube® and Tapertube® piles. This paper presents the results of the load test program and the issues related to pile driving induced vibrations and ground movement.

Jan 1, 2000

By Roberto J. Guardia, Tim Shell, Robert A. Robinson, Steve Rodolf

Our aging infrastructure includes numerous tunnels that provide easy access through topographic and societal obstacles. These tunnels are renewable resources that require periodic maintenance and rehabilitation to extend their useful lifespan to hundreds or even thousands of years. However, as with any structural rehabilitation project, tunnel liner rehabilitation requires an inordinate amount of evaluation and care due often poorly documented original construction and subsequent repair construction methods and materials. This paper documents the investigation, planning, design, and construction efforts of the rehabilitation of a 74-year old, 216-meter (713 foot) long two-lane highway tunnel in moderately fractured to highly sheared basalt on the Oregon coast. The tunnel consists of four sections lined originally with timber and subsequently overlaid with concrete, and three unlined sections.

Jan 1, 2005

By Harry R. Price, Bharat Doshi, Awni Qaqish, Abdul-Ghani Mekkaoui, Thaddeus Znoy, Ramesh Shukla

In 1992, a detailed inspection of the Southfield Sewer revealed a reach of approximately 0.8 kilometers in length, located directly below the freeway lanes, which was severely distressed. Failure of this section of the sewer would result in the closing of the busiest roadway in the state as well as the potential backup of sewage into homes and spilling into nearby surface waters. As such, repair of the distressed section required development of a procedure that would not jeopardize the conveyance of flow through the existing sewer nor impede travel on the overlying freeway. Based on these constraints, the DWSD and NTH team developed a repair concept that entailed the mining of a new, 3.05-meter (10-foot) diameter bypass away from the traffic lanes. The new bypass section was connected to the existing sewer, up stream and down stream of the distressed area, using a “top down” construction approach, that required only minimal freeway closures during weekend periods. This paper, prepared jointly by the Owner, Consultant and Contractor will describe existing conditions, design considerations and construction methods.

Jan 1, 2001

By A C. Edwards

The Mongol-Okhotsk belt consists of detached fragments of the Circum Pacific fold belt which have been trapped within the Mongol-Okhotsk fold belt. In its western part, the structures of the belt form an east-facing loop that is not connected with the other orogenic structures of Central Asia. In the eastern part of the belt (the Mongol-Okhotsk suture zone) the terranes form a zone between the Siberian craton to the north and the Bureya composite terrane to the south, that is linked with the Circum Pacific belt. The accretionary terranes, together with their Precambrian backstops, form a series of consistently-stacked, paired units that are bounded by northwest and north trending sinistral strike-slip faults. The ages of the rocks forming these accretionary complexes vary from Late Precambrian - Carboniferous in the west to Cambrian - Jurassic in the east. The terranes developed due to a progressive westward stacking of the accretionary complexes during the process of accretionary growth. The magmatic rocks young eastward indicating that migration of the magmatic front of the arc followed the eastward growth of the accretionary complexes. The accretionary terranes may be differentiated by their Paleozoic lithological assemblages. Only the Selemdzha, Niman, and Kerbi terranes located in the eastern part of the Mongol-Okhotsk suture zone contain significant amounts of black shale, and it is these terranes that host the bulk of the hardrock and placer gold mineralisation that is present within the suture zone. Gold mineralisation is present both as vein style and disseminated mineralisation within structural duplexes.

Jan 1, 1999

By Bas R. Hemmen

GeoBrain is a facility at GeoDelft with the purpose to provide society with all relevant geo-engineering knowledge and experience in a structured way. On the basis of the available knowledge and experience engineers, decision makers and construction supervisors can come to a fast, reproducible and objective choice, taking into account the consequences. The paper presents examples from the GeoBrain experience databases and forecasting models developed for foundation engineering and directional drilling, or: "GeoBrain Foundations" and "GeoBrain Drilling". GeoBrain is closing the gap between theory and practice. It is aimed directly at reducing uncertainty and the costs of failure, thereby increasing the quality of profession and minimising the risk in geo-engineering works.

Jan 1, 2006

By Anthony T. Xannacchione, Luis E. Vallejo

At present, there is little knowledge concerning the shear strength of clays containing floating rock particles with concentrations from 0 to 30%. In practice, the effect of rock particles is typically disregarded in shear strength analysis The two primary reasons for this are: 1) a lack of agreement concerning the influence of rock particles on material strength, and 2) the expense and difficulty of testing day-rack mixtures with existing laboratory procedures. These factors have impeded the development of successful slope remediation design techniques far colluviums derived from resistant sedimentary rocks or spoil produced from surface mining. This study reviewed 3 1 technical papers which contain analysis of shear strengths for clay and sands with varying mixtures of rock particles. These technical papers, published over the last 40 years, are comprised of field case studies, laboratory evaluations, and theoretical analysis. Evaluation of this body of knowledge ha shown that the shear strength gradually increases with increasing percentages of floating particles in unsaturated clays.

By V. Bush, T. G. Killingsworth, E. P. Ruffel

Effective and sustained corporate energy management programs are becoming a necessity for energy users as electricity deregulation laws are enacted on a state-by-state basis across the country and environmental regulations pertaining to emissions become more prevalent. The “Total Energy Asset Management” (TEAM) approach has been developed to assist energy end users with the development and implementation of corporate energy management programs designed to reduce energy risks and increase energy cost savings. This paper highlights the ways in which this approach can be applied to the mining industry while minimizing initial program implementation costs and increasing potential program benefits. Nearly the entire mining industry has become very focused on identifying opportunities to reduce costs per unit of yield. The industry as a whole has increasingly faced pricing pressures in large part due to the effects of global competition. The result of international marketplace participation and the emergence of higher efficiency recovery techniques have resulted in flat or even decreased prices for mining products. Thus, opportunities to reduce costs are actually opportunities to gain a competitive edge over similar mining operations. Due to the energy-intensive nature of many mining operations, the costs associated with energy are often a substantial percentage of operating costs. Therefore, it becomes very important to develop the corporate mentality that energy is an asset whose use should be optimized globally. In addition to the cost benefits of the TEAM approach, other benefits may occur such as reductions in facility greenhouse gas emissions.

Jan 1, 2002

By H. R. Shell

To obtain a better understanding of the crystallization of fluoride containing amphiboles from melts, an investigation of the range of stability between fluoramphi-boles and other minerals was conducted by the Bureau of Mines. This study has shown that the stability of fluoramphiboles is strongly influenced by both fluoride concentration and isomorphic replacement. Over 150 reactions were made with different compositions and reaction conditions. substitutions attempted and the phases that formed when the composition was crystallized by cooling from the melt are discussed. The attainment of equilibrium in these multicomponent systems is not claimed. Many ions that would be expected to enter the amphibole structure instead resulted in crystallization of phases other than amphibole. Those compositions that resulted in a high yield of acicular fluoramphibole by crystallization from the melts are shown in table 2. The fluoramphiboles obtained from melts typically had an acicular crystal habit and a hardness of 6 to 7 on the Mohs&apos; scale. Although many had relatively high length to cross section ratios, none were fibrous; it was concluded that the possibility of synthesizing a fibrous fluoramphibole from a melt was low. However, many compositions can be crystallized into a tough, hard, impact-resistant mass of interlocking acicular crystals.

Jan 1, 1958

By A. R. Sorta, D. C. Sego

ABSTRACT The settling, shear strength, and index properties of oil sands fines-sand mixture tailings (FSMT) for a wide range of solids and fines content are investigated. Results indicate that the liquid limit of FSMT obeys a linear mixture law. The fines-water ratio (FWR) governs the permeability of composite tailings (CT) and CT with comparable geotechnical behaviour can be produced from the same initial FWR mixtures. A phosphogypsum (PG) dosage > 900 mg/kg does not improve the dewatering behaviour of CT. The undrained shear strength of FSMT at the liquid limit is approximately 2.4 kPa, but is dependent on fines content at the plastic limit.

Jan 1, 2013