Search Documents

By Raymond P. Miller, David L. Monson, Robert A. Robinson

A geotechnical instrumentation program consisting of borehole extensometers and portable tape extensometer stations was effectively used to monitor concrete liner deformations and guide construction procedures during enlargement of a 75-year old Union Pacific Railroad tunnel in Wyoming. Enlargement involved excavation of the old concrete invert and placement of 5,941 feet of new concrete invert 6 feet lower in squeezing shales, fault zones and water-bearing sandstones. Instrumentation data were used to guide procedures for excavating the old invert, installation of temporary interior struts, underpinning existing liner walls, and placing the new concrete invert.

Jan 1, 1976

This consolidated index covers all publications of the Institute for the years 1926 through 1935. The following list indicates subjects of volumes and gives numbers or abbreviations used to designate them. TRANSACTIONS VOLUME *G26. Petroleum Development and Technology in 1925 (Published in 1926). *G26. Petroleum Development and Technology in 1926. *E27. Institute of Metals Proceedings. 73. Nonferrous Metallurgy, Milling and Concentration, Nonmetallic Minerals, Institute of Metals and Iron and Steel. [ ]

Jan 1, 1936

By L A. Maslov

We have considered the following characteristics of the crust and upper mantle of the Pacific Belt: seismic wave velocity anomalies, mechanical stress and shear deformation rate fields, heat flow and the pattern of metallogenic provinces of the Belt. It has been noted that there exist certain .regularities in distribution of the above mentioned geophysical characteristics and metallogenic zones within the Belt, displayed by prevalence of the lithophile elements in the Asia-Australian part of the Belt, and of the chalcophile ones within the American part.

Jan 1, 1995

IN dealing with this subject the intention is not to write a detailed description of the various methods in vogue on the Kalgoorlie field, but rather to give a brief outline of three of the methods which are most universally in force, and from which, ultimately, a few comparisons may be drawn. The three methods which the writer proposes embodying in this article are known as "The Rill," "The Flatback," and "The Shrinkage." For comparative purposes each method will be applied to a block of ore 500 feet in length, and opened up by levels 200 feet apart."The Rin" System. It is necessary in this system, for facilitating mullocking, to make connections between levels by rising and winzing at about every 100 feet or 150 feet along the orebody. After the leading stope is beaten off for the full length ofthe drive, the level is timbered. Single stulls are put in up to a width of fourteen feet. If the span is too great for stulls, set timbers or saddleback stuUs are used. Stulls are lagged over with 4-in gimlet poles, and wooden chutes are built at intervals of 50-feet. Ore passes are cribbed up through the filling directly above each chute, and are constructed of 7-in. round timber or 9 in x 3 in square timber, the passes measuring 4 ft x 4 ft in the clear.Occasionally a double pass may be carried up, one side serving as a travelling way. Stoping is commenced off the winzes, and rills are gradually formed, one on either end of each winze. The rills are generally at an angle of 37° off the horizontal, this allowing for the boring...

Jan 1, 1909

By Valois R. Shea-Albin

Increasing pressure from State and Federal agencies to mitigate mining-induced subsidence damage to overlying structures has presented a unique problem to the coal industry in the western United States. Because sandstone escarpments are an environmental issue, millions of tons of coal reserves that underlie these escarpments risk being classified as unminable by regulatory agencies. At this time, the effect of subsidence on escarpments has not been well documented or characterized. The Bureau of Mines is using numerical modeling techniques to analyze escarpment response to longwall mining. Two- and three-dimensional finite element models have been constructed for a study area near Price, Utah, where longwall panels were mined near an escarpment. This status report includes preliminary results showing that the pattern of subsidence surrounding the escarpment can be simulated through numerical modeling. Models that include such structural details as joint and fracture patterns will better simulate subsidence patterns .and magnitude. By locating longwall panels strategically in relation to the escarpment, stability may be preserved throughout the mining process. Numerical modeling provides a method to analyze relatively quickly the effects of longwall panel location and resulting subsidence on escarpment stability. The goal is to provide a relatively accurate predictive tool for mine planning to determine if escarpment stability can be maintained while maximizing extraction of the coal reserves.

Jan 1, 1986

By María Julia Ubillús Mellet

El presente texto complementa el estudio de las estrategias de seguridad en las empresas mineras a través de la alienación de las herramientas de gestión humana en una cultura de seguridad y prevención competitiva, de forma que se mejore el estilo de gestión en seguridad de los equipos gerenciales en las empresas mineras, y se desarrolle un manejo adecuado y responsable entre el área gestión humana y cultura organizacional. En ese sentido, la excelencia de gestión en seguridad radica en que el elemento humano se conecte de forma sistemática a las estrategías que la organización plantee.

Sep 12, 2005

By Gift Chisakuta, Bravo Mbao, Nils Schwarz, Angus Feather, Anthony Mukutuma

Bwana Mkubwa is a 50 000 tons per annum copper cathode producer, owned by First Quantum Minerals and located in Ndola, on the Zambian Copperbelt. The Bwana Mkubwa solvent-extraction circuit was started up in 1997. In 2002, the plant began treating ore from First Quantum?s Lonshi mine located in the Democratic Republic of Congo. The Lonshi ore is exceptionally fine and the amount of solids in the feed solution reporting to the solvent-extraction feed solution increased dramatically. Initially, crud was filtered in a filter press, but this rapidly blinded and seldom produced anything better than a wet sludge containing large quantities of organic. In December 2003 the decision was made to install a Flottweg Z4E-3/441 Tricanter® centrifuge to recover organic from the crud. The installation was completed in June 2004 and has since led to significant improvements in plant operability and savings in organic consumption.

Jan 1, 2007

By A. K. Anyimadu

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004, and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November 2006 at the Potgietersrus Platinum (PPL)?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Keywords: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, platinum, palladium, PGMs, tailings.

Jan 1, 2007

By George Piscsalko

There are numerous methods currently available to assess the integrity of drilled shaft and ACIP piles. Each method has its advantages and limitations. This paper will compare the various available methods as well as introduce a new method for assessing integrity of drilled shafts and ACIP piles. This new method, known as Thermal Integrity Profiling, determines the integrity of the shaft both inside and outside the reinforcing cage by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements can be made by either passing a thermal probe through a standard Cross Hole access tube, or from embedding thermal wires within the shaft. This Thermal Integrity Profile method will be described in detail and one case history will be presented. Additional testing methods which will be compared include low strain Pile Integrity Testing and Cross Hole Sonic Logging. Advantages and limitations for each method will be discussed.

Jan 1, 2011

By Osvaldo A. Bascur

Connectivity between mining and metallurgical process operations and their business systems has become a reality. Expanded use of plant information on the desktop is a standard tool for revenue improvement, cost reduction, and adherence to production constraints. The industrial component desktop support access to information for continuous improvement and innovation by staff personnel and engineers. Collaboration between groups enables the implementation of an overall process effectiveness index based on losses due to equipment availability, production recovery and quality rate. In this sense, the paper point out three cases studies of large integrated power stations.

May 25, 1998

By Susan E. Brink

The first step in determining whether Mn can be recovered by in situ leaching is to develop and test a selective lixiviant. Two column leach tests and one core leach test Were conducted by the U.S. Bureau of Mines on Mn oxide ore using aqueous sulfur dioxide (SO2) as the lixiviant. The column tests showed that aqueous S02 could selectively dissolve available Mn oxides from calcite-rich ore in a heap leach system. However, the core test showed that calcite gangue side reactions can have pronounced negative effects on the likelihood of successful in situ leaching of a calcite-rich ore with aqueous S02. Petrographic and geochemical analyses showed that both Mn (IV, III) oxides and calcite were dissolved. The abundance of dissolved Ca caused precipitation of gypsum. Acid consumption by calcite dissolution caused a rise in pH that caused the SO/S species to shift to S032-(sulfIte), which hindered reductive dissolution of Mn oxide. Gypsum precipitation did not affect complete leaching of the rock fragments in the column tests; however, it plugged the natural permeability in the core. Manganese recoveries were high for the column tests and low for the core test.

Jan 1, 2010

By Stephen C. Tadolini, Dennis R. Dolinar

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that are easy to handle/install under temporary or previously supported roof.

By J. Don Scott

Analytical predictions of the rate and magnitude of settlement of deposited oil sands tailings slurries generally overestimate how fast pore pressures will dissipate. Field deposits of nonsegregating tailings to mature fine tailings show continued high pore pressures near the surface which impede surface reclamation. In geotechnical analyses which predict the consolidation behavior of soft soils a finite strain theory is used. Effective stress-void ratio and void ratio-hydraulic conductivity relationships determined from laboratory large strain consolidation tests, are used in the finite strain predictions. This theory, however, cannot predict the full range of sedimentation, consolidation and pore pressure dissipation which occurs in large scale deposits of thixotropic tailings slurries. A new large strain consolidation model which assumes that the creep rate of the slurry exceeds the pore pressure dissipation rate is being investigated. This model is relevant for rapidly deposited, low permeability thixotropic slurries where the upwards drainage path increases by several meters a year, such as, in oil sand fine tailings ponds and nonsegregating tailings deposits. The model will be verified by analyzing the 10m high column of fine tailings at the University of Alberta which has been monitored for over 20 years and in which the excess pore pressures are still very high.

May 1, 2004

By V. Yahorava

Resin-in-pulp (RIP) technology has recently often been considered for the direct recovery of base metals and uranium from dense pulps. Implementation of RIP will eliminate the requirement for any solid-liquid separation downstream of leaching and has the potential to combine the recovery and purification steps, hence reducing both capital and operating costs. The recovery of the valuable metal is expected to be higher when RIP is used, especially where the leached solids are difficult to settle or filter, and to wash. The main concerns about the use of RIP for uranium recovery from dense pulps are the impact of silica on the resin?s metallurgical performance and the operating costs that would be associated with resin loss. Although a number of resin manufacturers have been developing much improved RIP-grade resins, it is critical that the most cost-effective resin be selected. Mintek currently is doing a significant amount of work on silica fouling of RIP-grade strong-base resins in acidic leach liquors and the effect it has on the performance of the resin, including its durability. This paper describes the results of the test work done on silica fouling and its impact on plant design input data. Resin durability test work was done using various laboratory techniques, but durability was also evaluated on a relatively large scale using actual pumps, screens, and mechanical agitation. Based on the results generated, a preliminary economical evaluation was done to estimate the impact of resin loss on the overall economic viability of a specific application. Keywords: resin-in-pulp, silica fouling, resin loss, equilibrium, kinetics, elution, durability, mechanical strength, resistance to attrition.

Jan 1, 2009

By J. Bruce Clemmer

In the experimental concentration of Vermont talc-magnesite ores, talc concentrates and tailings rich in magnesite were obtained. On account of the possible market value of the magnesite, the tailings are given consideration' in this report along with the talc. After some comments about the talc industry, the magnesite that accrued as tailings will be considered. Then the flotation results will follow.

Jan 1, 1936

Research into the mechanisation of ore winning from the very narrow reefs characteristic of South African gold mines has been conducted from as early as 1964 through the Chamber of Mines Research Organisation (COMRO) but with limited success. However, the Council for Scientific and Industrial Research (CSIR) has recently re-evaluated the potential for the mechanisation for the narrow tabular gold mines. It has been determined that there are approximately 22 000 tonnes of gold left in-situ in channel widths of less than 500 mm in thickness. The extraction of ore from such reefs requires a complete paradigm shift in that the current mining cycle (drilling, blasting, cleaning and supporting) is not feasible since such a stoping width would not allow the workers entry into the stope. Consequently, a non-entry form of mining is required. With this target in mind CSIR has invested in a project called the Nederburg Miner which seeks to identify new technologies for drilling, rock breaking, cleaning, and materials handling, the application of which will enable non-entry mining of very narrow ore bodies. The intention is to develop a fully automated system that will not require human involvement at the stope face. The outcomes of research into this proposed system will not only extend the life of South African gold mines but will also enhance South Africa's reputation for excellence in mining research. This paper presents the new technologies under consideration and potential methods for their application into an integrated non-entry mining system.

Jan 1, 2008

By Y Sha

During the last two decades, China has expanded its iron and steel industry very quickly, from less than 100 Mt/a steel production to over 700 Mt/a. It caused big increases in both domestic iron ore production and imported iron ore quantities year by year. The mode of iron ore supply has changed from almost all domestic supply to major tonnes of imported ore plus domestic ore supply. Over 200 blast furnaces with volumes larger than 1000 m3 each have been built and put into operation. Sinter machines have been enlarged quickly. There are now 135 sinter machines with =200 m2 sintering area each. Pellet production increased from 11.94 Mt in 1999 to 210 Mt in 2011, resulting from rapidly increasing domestic concentrate supply and rapid development of the grate-kiln process. The typical ferrous burden constitution is high basicity sinter plus pellets plus lump. The pellet proportion increased and the sinter proportion decreased gradually. A lot of technical improvements, like deep bed sintering, sintering with a high ratio of limonite, composite sintering, pellet process optimisation, a high ratio of hematite in pelletisation, blast furnace operation with low-grade ferrous burdens and hazardous element control, etc have been made to enhance iron burden quality and to reduce hot metal cost. Chinese iron and steel production is expected to increase slightly in the next few years. Its overcapacity should be controlled effectively. Given the variations of iron ore supply, pellet production will keep progressing in terms of production scale and pellet quality, the sintering process will be improved further by various measures to utilise different ores efficiently, and ferrous burden constitution will be optimised continuously to realise the lowest cost of hot metal production.CITATION:Sha, Y and Wang, Z, 2013. The Chinese iron and steel industry response to the challenges of iron ore supply, in Proceedings Iron Ore 2013 , pp 7-14 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Gold, silver and palladium may be separated from the other base metals and sulphur contained in copper sulphide precipitates derived from the Sherritt-Gordon nickel process using a process involving an oxidation roast, a reduction roast and a Cu(II)/acetonitrile leach. Sulphur is removed as SO, in an oxidation roast and the hot calcine is reduced with carbon, or with carbon plus cuprous chloride. The resulting product contains metallic copper which is readily dissolved with cupric ions in aqueous acetonitrile solution. Copper powder is recovered by thermal disproportionation. The residue contains the bulk of the iron and precious metals and may be treated by a number of methods, including direct cyanidation or melting with suitable fluxes. Melting the residue will produce a copper alloy containing the precious metals and remove the iron as a slag. The alloy can be recycled to the copper leaching stage or sent for toll refining depending on the precious metal content. Impurities from the leaching circuit are controlled by a bleed circuit which in one approach utilizes the SO, from the calciner to produce Chevreul's salt and separates copper from the soluble cobalt and nickel. Alternatively, the bleed may be directed back to the main refinery copper boil stage or oxydrolysis stage.

Jan 1, 1982

By Huilan Yang, Feng He

This paper intends to introduce the development of copper smelting and converting technologies in China in recent years, with a particular emphasis on the introduction of various continuous converting technologies, and moreover, it analyzes the advantages and disadvantages of those technologies, including their impact on the downstream anode refining from different points of view. INTRODUCTION At present, many converting technologies are used in copper pyro-metallurgical plants in China, including Peirce-Smith (PS) converter, flash converting furnace, multi-lance based top blowing, bottom blowing and so on. These technologies have spanned a wide range of time. PS converter technology has been applied in copper smelters for many years and most of the blister copper have been produced by this technology; flash converting technology has been developed since 1990s and been maturely applied in several plants up until now; top blowing and bottom blowing technologies have been revived in China in the past decade and boast good environmental protection performance, energy efficiency, throughput capacity and short process flow. All of the said technologies have reference operations in treating high-grade matte. As more and more attention is paid to environmental protection globally and copper smelters continuously seek for cost reduction, it is necessary to share those converting technologies, especially those new converting technologies derived in China, with copper smelting practitioners in the world. This paper aims to analyze the advantages and disadvantages of various technologies from a macroscopic view and discuss their actual application effects, current developments and future improvements. BRIEF INTRODUCTION OF VARIOUS CONVERTING TECHNOLOGIES IN CHINA China has seen a rapid development in copper smelting industry in the past 30 years and has become the largest gathering place of copper smelters in the world, most of which are operating with PS converting furnace technology, however, with the increasingly strict environmental requirements of the Chinese government in recent years, the low-level pollution issue and the disadvantage of large gas exhaust amount per unit of copper of converting furnaces are particularly prominent.

Jan 1, 2019

By P. L. Swanson

Stability analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is Limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this U.S. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 2010