Search Documents

By Mahyera A, Sakashita B, Ahmed U, Abou-Sayed AS

Gas in U.S. coals is primarily composed of 90 to 99 percent methane and up to 10 per- cent carbon dioxide. In composition and heat- ing value, this coal-bed gas is similar to natural gas and can be introduced directly into commercial pipelines after standard condition- ing. The high permeability cleat system in the virgin coal can be exploited in order to drain the coal gas well in advance of mining. Two premining drainage methods have been extensive- ly evaluated in the U.S.; they are 1) horizon- tal boreholes collared from within the mine, and 2) vertical drilling from the surface with fracturing. Limited-size fracture treatments are advocated in order to prevent potential roof damage and the need for added support. An engineering approach to predicting gas flow for different drainage techniques near mining locations is presented. Results can be used in design, i.e. pipeline, compressor. Coal gas drainage from a horizontal borehole and a treated (contained fracture) vertical well for a 6 foot seam have been evaluated. Based on these results, it was concluded that selection of gas drainage techniques will depend primar

Jan 1, 1982

By Hornsey R., P. van der Merwe

The Two Rivers Project is a feasibility study to evaluate the UG2 chromitite layer on Dwarsrivier372KT, Mpumalanga Province, South Africa. The project, which commenced in August 2001, is expected to receive go-ahead early in 2003. The project sponsors (AVMIN 55%, Implats 45%)required project delivery within a short timeframe requiring optimization of the geological and geostatistical programme. Geological modelling was carried out in parallel to the drilling programme, and significant up-front geostatistical preparatory work was done. The time saving was approximately 4 – 6 months on project delivery. The cost saving to the project (excluding NPV considerations) is estimated at R20–30 million. Keywords; Two Rivers Platinum, Dwarsrivier 372KT, UG2 chromitite layer.

Jan 1, 2003

Overcasts are indispensible ventilation control devices to permit one airway to pass over another without mixing in room and pillar coal mining. The airflow distribution inside the overcast depends on its spe-cific configuration at which the flow enters into it. This study uses 3D numerical simulation to examine the pressure and velocity distributions inside an overcast. The effects of the overcast angle on the flow field are also examined. The flow is assumed to be turbulent and isothermal and the standard k-e model is utilized. Simulated results display flow separation and recirculation regions of different sizes occurring not only upstream and downstream from the overcast but also inside it. The results also show that the size of the recirculation regions in-creased with the increase in the angle before and after the overcast influencing significantly the flow field and pressure losses. The stream-lines are plotted to show the 3D structure of the flow field. The results from the simulation can guide overcast design commonly used in un-derground coal mines. Keywords: 3-D simulation, Overcast, Room and Pillar, Turbulence, Recirculation Region

Feb 27, 2013

By João Júnio Pereira Lino

Este trabalho tem como objetivo demonstrar a influência da laminação de desbaste durante o processo de laminação termomecânica de um aço microligado ao Nb, Ti e V, obtido em um laminador Steckel, nas suas propriedades mecânicas. Duas variações do plano de passe para realização da laminação de desbaste foram propostas. As variações consistiram na diferenciação da redução passe a passe de forma a obter diferentes refinamento de grão ao fim do processamento de desbaste. O processamento de um aço com composição química adequada à obtenção de propriedades mecânicas compatíveis com o grau LNE380 especificado na norma ABNT NBR 6656 é demonstrado. Foram alcançados limites de escoamento a 0,2% de deformação e a resistência à tração na condição 1 de 459MPa 563MPa e na condição 2 de 505MPa e 601MPa respectivamente, sendo que na condição 2 foram obtidos acréscimos de em torno de 40MPa em ambos LE e LR.

Oct 30, 2017

By R. J. Visintainer, W. L. Whitlock

"Difficulties with the sizing and operation of centrifugal froth pumps are common and the underlying fluid dynamics are complex. Design and selection often relies on previous experience, offering unreliable guidance for novel applications or unexpected problems. The current paper describes a program of extensive laboratory testing on froth handling centrifugal pumps, covering a range of flows, heads, speeds, viscosity, air content and froth stability. Variations in impeller vane design and the effectiveness of an airlock venting apparatus were also examined. The program resulted in a better understanding of centrifugal froth pump dynamics and insight for the troubleshooting of field applications.INTRODUCTION The Challenge of Pumping Froth In pumping mineral processing froth, the handling of large quantities of air within the fluid is often unavoidable. Efforts to reduce the amount of air present at the pump suction, while always recommended for improving pump performance, may have limitations. Some strategies may also carry an economic penalty, such as unwanted process dilution (e.g. due to water spray or injection), or increased capital cost of equipment due to oversized pumps, sumps and/or piping. Froth pumping losses fall into several categories, as described below and represented graphically in Figure 1. • Density effects: Entrained air reduces the pressure created by the centrifugal pump in direct proportion to the reduction in bulk density. This is not a true “loss”, since the head produced by the pump (in meters of froth), may remain unaffected. However, the reduction in pressure often leads to a corresponding increase in pump speed required to drive the system, which itself leads to increased NPSH required by the pump (NPSHR). Furthermore, by adding a gas phase, the overall volumetric flowrate is increased, assuming a fixed quantity of de-aerated liquid being handled. This leads to increased suction velocity which further reduces the NPSH margin by simultaneously increasing pump NPSHR and decreasing system NPSH available at the pump suction (NPSHA). • Viscosity effects: Increased viscosity introduces an additional factor in some froth pumping applications, such as oil sands bitumen froth. Losses result from increased shear stress within the fluid flow, which increase with flowrate. Viscosity also facilitates the formation of airlock by reducing turbulence and allowing individual bubbles to coalesce more easily within the flow stream. Finally, it increases pump NPSHR by increasing local pressure drop in the vicinity of the vane inlet edges. • Airlock effects: Also known as air binding, it occurs when air or gas coalesces within the pump suction or impeller passages and begins to collect there, held by buoyancy forces within the rotating flow field. In essence, the liquid “floats upwards” towards the pump suction against the outward directed centrifugal forces. The airlock acts as a blockage, with corresponding reductions in flow, head and efficiency. NPSHR also increases, due to increased velocity and distorted streamlines in the flow circumventing the blockage."

Jan 1, 2012

By Junfeng Shen

Geosynthetic clay liner (GCL) is a kind of waterproofing material used widely in engineering. The waterproof mechanism is understood in terms of bentonite particles becoming a water-obstructcolloid layer after they absorb water and swell. The swell stress, however, has not been determined directly till now. In our experiment, the swell stresses of the GCL under saturated and water absorbing conditions are measured directly using a custom-made instrument. The results show that (1) the instrument designed by the authors performed satisfactorily and the test results are reproducible; and, (2) The trend line of swell stress variation with time can be divided into three segments. The first segment is characterized by a quick increase of the swell force in the first 0?50 hours. The swell stress increases by 7.00×10-4?1.00×10-3 Mpa / hour. The second segment shows a slow increase of the swell stress during the 50?1730 hours. The swell force increases by 7.54×10-6?2.02×10-5Mpa / hour. The third segment is characterized by little variation in the swell stress after 1730 hours. In this segment, the average value of the swell stress measurements is 0.0719Mpa and the maximum value is 0.0729Mpa. It is suggested that the swell stress is mainly raised by water entering the pores among montmorillonite particles and the interstitial layers in individual montmorillonite crystals, leading to an increase in volume and manifested as a stress on the surrounding materials.

Jan 1, 2006

Mount Isa Mines Limited first installed electronic data processing equipment in 1959. The decision to replace this equipment with a computer was motivated by the need for greater processing power and the availability of new and less expensive computers. Consideration of hardware software and delivery features of available equipment, resulted in the selectIon of an ICT 1900 series computer which was installed in March 1966. Special air-conditioning and power stabilization equipment was also required.Systems design and programming was carried out by personnel recruited from within the Company and trained by the computer manufacturer. Early work was hindered by the problems of remote location.Initial applications were basically accounting functions whIch were taken over from the EDP installation. Subsequently computer applIcatIOns of a more complex technical nature have been undertaken. Future work will include both "scientific" and data processing applications.

Jan 1, 1968

By D. Schreuder

Conditions in the South African market relating to atmospheric emission control has changed dramatically over the last 10 years. Companies have become more responsible, environmentally aware, and have to comply to more stringent environmental limits set by legislation. This paper describes briefly the current best available atmospheric pollution abatement technologies relating to particulates, acid gases, NOx, acid mists, aerosols, mercury, dioxins and furans. Mention is also made as to the best practices for product work-up and waste product disposal.

Jan 1, 2006

By M. W. Robotham, H Wang

removal efficiency is analysed from a stochastic

Apr 1, 1995

By A J. Eggers

With gold first discovered at Carrick in 1864, exploration and mining on the Carrick Goldfield in Central Otago, New Zealand, has now been ongoing for more than 130 years. Recorded historical hard rock production from up to 52 different mining claims from 1864 to about 1921 is 24,047 ounces (oz) of gold.   Since 1980 Amoco Minerals New Zealand Limited, CRA Exploration Pty. Limited, Amax Gold Mines New Zealand Limited and Summit Gold (New Zealand) Limited have conducted modem systematic exploration campaigns targeted at locating shear controlled gold bearing quartz lodes and stockwork deposits. More than NZ $1million has been spent by these companies on aerial photography, geological mapping, stream sediment surveys, soil and rock chip geochemistry as well as reverse circulation (RC) percussion and diamond drilling.   RC drilling by Summit Resources in 1997 has identified a 1,500 m long zone of low-grade gold mineralisation at Lower Carrick, with an average grade of 1.00 g/t Au over a 14 m average thickness. This gold mineralisation, hosted within a low angle shear zone, has analogies with the Hyde-Macraes Shear Zone in eastern Otago. Recent exploration and drilling at Carrick has revealed the potential to discover large (>0.5 million ounce (Moz)) low-grade bulk shear controlled quartz vein and stockwork gold deposits similar to those now being mined at Macraes.

Jan 1, 1997

By Paul F. Gnirk, Ralph A. Wagner, Joe L. Ratigan

This thermomechanical analysis used the finite element method to investigate the behavior of crushed salt backfill in a waste disposal room situated in a salt dome repository. The first of two objectives was to determine the transient temperature rise and degree of thermomechanical consolidation that occur in the backfill as a function of drillhole depths. The second objective involved the evaluation of closure due to salt creep of unlined emplacement drillholes and the determination of pressure on steel sleeve liners in the drillholes should liners become necessary for canister retrieval. The retrievability period was considered to extend for 25 years after waste emplacement. The canisters were assumed to contain ten-year old high level waste with a thermal output of 4.3 kW at the time of emplacement.

Jan 1, 1981

By J. M. Singer

The Bureau of Mines investigated the threshold of dispersal of monolayers and piles of rock dust, anthracite, and Pittsburgh seam coal dust in a small wind tunnel that simulated a coal mine gallery, with the objective of preventing or limiting the formation of flammable dust clouds. The effect of selected variables on entrainment velocity was examined. Mode of entrainment and flow processes in the wake region of dust configurations were investigated by means of high-speed motion pictures. Significant results were as follows: 1. Local minimum air velocities required for dispersal were only slightly higher for shallow dust ridges than for dust particles. 2. Minimum velocities for entrainment of dust particles from smooth glass and coal surfaces increased in the order rock dust, anthracite, Pittsburgh seam coal. 3. The mechanism for dispersal of dust poles depended significantly on dust pile geometry, cohesiveness of dust, bulk density and compaction of dust, adhesive surface, and vibrations perturbing the supporting surface.

Jan 1, 1969

By Keith R. Vining

Solid fuel, usually coke or anthracite, is commonly added to ground iron ore fines in the pelletising process to reduce the amount of burner fuel required and the maximum firing temperature, while maintaining pellet strength and the productivity of the pelletising plant. However, the use of coke and coal contribute to the production of greenhouse gases (eg carbon dioxide) and are a source of NOx and SOx emissions. Utilising wood biomass / wood char is one methodology CSIRO Minerals is investigating as an alternative to coke and coal, as it is a renewable energy source that is very reactive, has a low ash content and the potential to reduce emissions of greenhouse gases from the iron and steel-making process. Previous work has established that charcoal can effectively replace coke in the sintering process (Lovel et al, 2005), and the following experimental work aims to demonstrate that it can also provide an adequate replacement for coke and coal in the pelletising process. The paper presents the results of an experimental testwork program comparing the behaviour of fired pellets containing traditional solid fuels and charcoal. The physical properties of the pellets are compared in terms of their compressive strength, tumble and abrasion indices and the reduction properties. A qualitative assessment of the pellet microstructures is also presented.

May 1, 2007

The process of electrostatic separation was developed in the late 19th century, but did not make much headway for about 25 years. High dc voltages, of the order of 20 kilovolts, are involved, and the only means of obtaining such voltages at that time were by the use of frictional machines, such as the Wimshurst. These were not reliable, for two reasons:-a. If a spark discharge occurred it took an appreciable time before a steady voltage was again attained.b. In damp weather the machines were almost useless.In the first 20 years of the 20th century the advent of mechanical and vacuum-tube rectifiers led to promising developments of 'the process. In the early 1920's flotation became widely used commercially, and proved to be more reliable, and capable of wider application, than electrostatic separation. During the last 15 years or so, with a better knowledge of the fundamentals forming the basis of the process, electrostatic separation is beginning to compete with flotation, especially in the treatment of smallsizedgranular material, such as beach sands. Electrostatic separation can be, and is, widely used in many cases where flotation is impossible, such as in the cleaning of food products which must be kept dry.

Jan 1, 1950

By A. Mboma

Keywords: Furnace, decommissioning, care and maintenance, re-start, funding, nickel Bindura Nickel Corporation (BNC) operates two nickel mines, and treats concentrates from these mines as well as toll concentrates from the region around its Bindura Smelter and Refinery (BSR) complex. At the smelter, concentrates of at least 5% nickel content are blended and dried to 4% moisture in a coal-fired rotary kiln. Matte smelting of concentrate is carried out in a six-in-line electric arc furnace, where the furnace slag is granulated and discarded. Furnace matte is transferred via ladles into Peirce-Smith converters, where, after granulation, a leach alloy containing 68%Ni, 20%Cu, and 6%S is produced. Converter slag is recycled via the matte-smelting furnace. The onset of the global economic recession towards the end of 2008 resulted in a collapse of metal prices, worsening the local situation that was already marred by unfavourable macro-economic conditions in Zimbabwe. As a result, BNC mines were put on care and maintenance in November 2008, followed by Bindura Smelter and Refinery in February and March 2009 respectively. The business environment has since changed, and BNC is getting ready to re-start the plant. This paper describes the decommissioning of the Bindura furnace, asset preservation during the care and maintenance programme in the past two years, and preparation for starting up of the Bindura smelter in the near future.

Jan 1, 2011

By Paul S. Fisk, Arne Fareth, Julie Frietas, Francis Lo, Fidel L. Mallonga

INTRODUCTION This report describes the inspection of parts of the New Croton Aqueduct (NCA)undertaken for the New York City Department of Environmental Protection (NYCDEP)by Parsons Brinckerhoff Quade & Douglas, Inc., (PB) in association with Montgomery Watson Engineers of New York, P.C. (MWH). Support for the inspection was provided by AFC Enterprises, Inc., under Construction Contract CRO-333, “WM-11 New Croton Aqueduct Rehabilitation and Inspection Program.” The scope of the inspection work under CRO-333 included assessing the condition of the 10.3 km (6.4 mile) long, pressurized section of NCA and inspection of shafts, head houses and blow-off structures in both the pressurized and gravity sections. The CRO-333 inspection continued investigation work begun under ContractCRO-196, which ran from 1993 to 1997. The CRO-333 inspections were conducted from November 2004 to September 2005. Background The New Croton Aqueduct was put into service in 1891 to deliver water from the Croton River Watershed in Westchester County to consumers in New York City. Figure 1 shows the location plan of Croton Water Supply System. The design flow into Jerome Park Reservoir was 12.7 m3/s (290 mgd) and into the135th Street Gate House, further south, was 10.9 m3/s (250 mgd). The NCA has been operated as a gravity conduit from Croton Lake to Gate House No. 1, just north of Jerome Park Reservoir, since its original construction. The length from Gate House No. 1to 135th Street, which includes a major siphon under the Harlem River, has been operated under pressure. Croton Lake gate house, the north end of the alignment lies at Station 4+75; Shaft 33, the south end of the alignment lies at Station 1628+05. The diameter of the tunnel is 3.2 m (10.5 ft) in the siphon and 3.7 m (12.3 ft) in the Bronx and Manhattan sections. The pressurized sections, constructed in rock, consist of a brick lining surrounded by a mortared and grouted rubble backing. Figure 2depicts a typical tunnel cross section. The objective of the shaft and tunnel inspections was to locate and document defects, such as leaks, deterioration of lining material, cracks, spalls, delaminations,

Jan 1, 2007

As part of its research on advanced mining technology, the U.S. Bureau of Mines emphasizes studies on in situ leach mining. This research enables the Bureau to develop technical information that can allow mining companies to adopt in situ leach mining methods. Research results should help to remove the technical and economic barriers currently hindering the development of commercial in situ leach mining operations. This report contains papers summarizing results of Bureau research on various aspects of in situ leach mining. A featured topic is the cooperative field experiment of the Bureau and Santa Cruz Joint Venture in a copper deposit near Casa Grande, AZ. Discussions in-clude an overview of the entire project, cost modeling, environmental permitting, laboratory core-leaching experiments, petrographic studies, and an evaluation of the geologic structure in the region. In addition, papers describe hydrologic modeling and geophysical studies of solution flow during leaching. Preliminary geochemical modeling studies are also summarized. A final paper describes a nonionic chemical additive with potential for significantly reducing the high costs of drilling in in situ leach mining.

Jan 1, 1989

By John E. Tilton

The ability of companies and countries to mine copper and other mineral commodities competitively and in the process to generate new wealth depends on their mineral endowment. Chile, for example, produces and exports copper because it is well endowed with high-quality, low-cost deposits. This production creates wealth that benefits mining companies and their stockholders, the government, local communities, as well as copper consumers around the world. The widespread perception that mineral endowment must largely determine competitiveness, or what economists call comparative advantage, must be true at any particularly moment. Countries with abundant reserves must be competitive. This follows from the definition of reserves — the quantity of a mineral commodity found in discovered deposits that are profitable to exploit under current conditions. As a result, it is a tautology and not particularly interesting. The important question is what causes reserves to change over time, producing in the process new wealth and shifts in competitiveness?

Jan 1, 2003

By Martin Hertzberg

This Bureau of Mines study concerns the use of the tube bundle method as a sensitive and reliable detector of mine fires. The method involves the pneumatic, sequential sampling of many points in a system through branching tube bundles that lead to a single analytic station of high sensitivity, good reliability, and convenient location. Two serious limitations inhibit its use: the relatively slow response times for long lengths of narrow sampling tubes and the wall-diffusion losses for submicrometer smoke particulates. These limitations were quantitatively evaluated by measuring tube transit times and smoke particulate transmissions as a function of tube length, diameter, and pressure drop. The comparison of the data with theory offered the challenge of extending the classical, incompressible flow solutions to the two compressible cases: isothermal and adiabatic. New equations were derived for these cases, and the measured transit time data gave reasonable agreement with calculated solutions in both the laminar and turbulent regimes. The measured transmission losses of smoke particulates from several combustion sources compared favorably with those expected from Brownian diffusion losses to the interior walls of the sampling tubes. Traveltime and smoke transmission graphs are provided and, pump power requirements are estimated.

Jan 1, 1976

By D. Bessinger, J. M. A. Geldenhuis

High titania slag is produced from the smelting of ilmenite. These slags contain approximately 85 per cent TiO2 and consist mainly of a M3O5 solid-solution phase. During cooling the slag can decrepitate to a fine particulate material, which decreases the value of the product. Based on X-ray diffraction analyses of the decrepitated slag after cooling, it was found that the M3O5 phase had almost disappeared. The disappearance of the M3O5 phase was linked to oxidation of the slag. A M6O11 phase formed in the decrepitated slag. It is postulated that decrepitation of high titania slag is caused by volume changes due to the oxidation of the M3O5 phase in the slag.

Jan 1, 2005