Search Documents

By Z Li, A Fleming, S Webster, L Snyman

Northparkes Mines is developing the E26 Lift 1 North block cave mine, which is adjoined to the existing E26 cave. This paper presents the challenges and methods used to design the ground support system during the feasibility study. Calibrated numerical simulations were conducted to forecast the levels of rock mass damage and to assist the ground support design. Generally, low to moderate rock mass damage is forecast on the extraction and undercut levels. However, poor ground conditions are expected in sheared and preconditioned zones adjacent the existing E26 cave. This will result in difficult ground conditions during development, undercutting and drawbell establishment. Empirical assessments were conducted to make sure the ground support system is able to handle both the static and dynamic load demand, and to accommodate the deformation values. A safety factor of 1.5 was used for the designs to cover the unknown rock mass conditions and potential for larger seismic events. Learnings from the E26 Lift 1 and SLC, also mining against the E26 cave, are incorporated into the design. Fibrecrete, mesh and resin bolts / mechanical anchors are the primary ground support system used, and cable bolts for intersections with a span of more than 6 m. Following undercutting and during the operating life of the mine, secondary ground support and rehabilitation will be required.

Mar 15, 2021

By E. Harris

Frithia humilis is an endangered succulent plant species. Its distribution range overlaps with the coal fields of Mpumalanga and it is therefore threatened by opencast mining activities in particular. One of the 11 known populations of F. humilis was translocated from a licensed coal mining site to three suitable receptor sites within the species? distribution range. A longterm monitoring programme was initiated to track the progress of the newly established populations. Temporal trends in population demography, size classes, and fecundity were recorded. Population numbers of size classes fluctuated annually. However, flower frequency increased over time and seedling recruitment contributed significantly to population growth. Receptor sites with similar geological conditions to the donor site had more persistent cohorts, which suggest that such sites should receive priority during the translocation of endangered edaphic specialists. This study not only confirms that a Frithia humilis population can successfully establish after a translocation, but also serves as an important baseline for future comparative purposes to gauge the long-term success of the translocation effort.

Jan 1, 2014

The ready solubility of gold in dilute aqueous solutions of the cyanides of the alkalies or alkaline earths provides a convenient method for the separation of the precious metal -from the large surplus of associated materia1. The finely ground ore is pulped with a weak solution of cyanide, agitated to dissolve the gold, filtered and washed. The lowgrade filtrate is then clarified and the gold precipitated by some electronegative agent, the most usual being finely divided zinc or zinc dust. The slight precipitate is collectedon some form of filter coated with a filter aid, the filter cake being then known as "gold slime".A typical analysis of this slime is given in Table 1.

Jan 1, 1956

By M. J. Hannan

Considerable interest has arisen in developing analytical methods suitable for measuring resource commodity substitution patterns. some of this work has applied the Translog method to estimate actual elasticities of substitution. Recent examples incl.uae Privolos and Dunietz (1987), Kopp and Smith (1983), and Moroney and Trapani (1983). Another method, one which has received attention earlier in the work of Fisher and Pry (1970), is that of the logistic or diffusion function. We believe that the latter method has properties suitable for analyzing current problems of material substitution. The present study thus evaluates this method in its original logistic form as well as an extended version incorporating additional explanatory influences. The analysis is applied to copper/aluminum substitution and iron ore beneficiation. Substitution for copper by aluminum is examined in the building wire and cable, and magnet wire end-use markets. For iron ore, the substitution of pellets for sinter is considered for the U. S. market.

Jan 1, 1990

During the last 125 years, the steel industry has witnessed revolutionary changes in the process of steelmaking. The Bessemer process was the predominant steel production technology during the last two decades of the 19th century. The open hearth process accounted for the lion's share of world steel production for six decades from 1910 to 1970. With the appearance of the LD process on the industrial stage in 1952, the importance of open hearth process declined and currently the basic oxygen processes are contributing more than 60 per cent of the world steel production. The LD process also led to the development of several other oxygen blown processes such as LDAC, OLP, OBM, QBOP, EOF, Clc.

Jan 1, 1999

By V. B. Dale

This paper is one of a series covering the mineral resources of the Nation. It briefly describes most of the known tungsten deposits of New Mexico. Most of the descriptions are from field examinations by the senior author. Reported tungsten occurrences that were not visited are listed below: Colfax County: Occurrences of ferberite in thin veins in Willow Creek near Elizabethtown.4/ Dona Ana County: Small, low-grade occurrences of scheelite near the summit of the Organ Mountains about 15 miles east of Las Cruces. Hidalgo County: Scheelite reported in the Daisy mine 7 miles southeast of Hachita. Ores are carbonates containing copper, gold, silver, and bismuth.5/

Jan 1, 1959

"This paper deals with the reconciliation of open stope performance at Olympic Dam, South Australia, with a focus on stope stability, recovery, and operational aspects of stope reconciliation in relation to the expected or planned stope design. The observed stope performance is inconsistent with the equivalent linear overbreak sloughing criteria for assessing the performance of large open stopes. The aim is to investigate new stope performance criteria using quantitative (overbreak, underbreak, maximum depth of wall failure) and qualitative (stope productivity, observed fragmentation) information that correlates with the observed stope behaviour, providing a process for improving future stope designs.RÉSUMÉ Le présent article traite de la réconciliation de la performance des chambres ouvertes à Olympic Dam, Australie du Sud, en ciblant la stabilité des chambres, la récupération et les aspects opérationnels de la réconciliation des chambres par rapport à la conception attendue ou planifiée des chambres. La performance observée des chambres ne concorde pas avec les critères d’épaisseur équivalente du bris hors profil pour évaluer la performance de grandes chambres ouvertes. L’objectif est d’étudier de nouveaux critères de performance des chambres au moyen de données quantitatives (rupture hors profil, rupture à l’intérieur du profil planifié, profondeur maximale d’effondrement du mur) et qualitatives (productivité de la chambre, fragmentation observée) qui concordent avec le comportement observé des chambres, fournissant ainsi un processus pour améliorer les futures conceptions des chambres."

Jan 1, 2015

By John Starkey

"During the period June 2007 to March 2007, John Starkey of Starkey & Associates (Starkey) worked in Russia for High River Gold, supervising the engineering design work that was being done at the IRGIREDMET Research Institute, in Irkutsk Russia. The work entailed moving the Newmont No. 4 mill from Elko, Nevada to Berezitovy, a mine site north and west of the city of Skovorodino, in the Amur Region of Siberia. This was a grass roots project and required construction of all phases of the infrastructure and process facilities that are associated with a 5000 t/d open pit mine and CIP mill.During the course of this engineering design exercise, many aspects of doing business in Russia were encountered, with regard to laws, norms, and business practices. This paper discusses many of these findings. Also by living in Irkutsk, many observations on Russian life and social customs were made and these merit discussion from a general interest point of view.Prior to going to Russia, another engineering and ore testing firm (TOMS) had approached Starkey to find out if Starkey could assist them in upgrading their SAG ore testing procedures to Western standards in order to offer their clients turnkey projects, that included reliable SAG and AG grinding. TOMS was aware that Starkey had invented the SPI test but did not know that the SAGDesign test had by then been fully developed and was being offered commercially as the most accurate way in the world to design new grinding mills. They were also unaware that this new testing method had been patented by Outokumpu (now Outotec) and that this method allowed them access to a design method, through Starkey, that would lead to a manufacturer’s guarantee (by Outotec) of throughput and grind for any new semi-autogenous or autogenous grinding circuit, with or without ball mills.When Starkey started working at IRGIREDMET in June 2005, they also made a request to add a design method for SAG mills that would be considered acceptable to Western clients. From these requests, presentations were made in Russian to both institutes and each decided to join the SAGDesign Consulting Group as satellite members and buy a SAGDesign test mill to use with their Bond Ball Mill Work Index mills, to provide SAGDesign testing services. To complete the service, contracts have been put in place for Starkey to use these results to design new grinding equipment and to train engineers at TOMS and IRGIREDMET how to do this work.Starkey also undertook to train engineers at both labs to go into the field and to take the samples for SAGDesign testing programs. It is here where the SAGDesign testing service upgrades other grinding test programs because the samples to be used for design are professionally chosen, and the results will be much more likely to produce a satisfactory design. Starkey is a mining engineer and is uniquely qualified to do this task. This and the SAGDesign test are the key components that lead Outotec to offer a performance guarantee for mills designed by Starkey."

Jan 1, 2008

By F. Z. Suo

Baoahan Iron and Steel Complex is situated at lower beaches of the Yangtze River. The subsoils 50~70 M below the surface is a deposite of Yangtze River delta, consisting mainly of weak silty clay and loam, with low soil bearing capacity. Consequently, to build on such a weak soil a grant iron and steel integrated works weak soil improvement at the Complex, pile foundation is the effective type. It is estimated that at the first stage of Baoshan project 60,000 piles have been driven, of which 60% are steel pipe piles and 40% reinforced concrete piles. To provide reliable basis for pile foundation design, on-site loading tests were carried out for long reinforced concrete piles 27,45 60 M in length ,with strain gauges on the chief reinforcement of pile shaft and strain rod on pile tip. Based on loading tests, the paper discusses and analyses some issues, including determination of load transfer mechanism distribution of frictional resistance. Tests show that as far as long friction piles in soft clay are concerned, regardless of the properties of pile tip's bearing stratum, loads are mainly carried by shaft frictional resistance which it is effective to determine pile capacity in terms of P ~ S relationship.

Jan 1, 2010

By Derek V. Ellis

Coastal and marine mines affect the seabed?s biological resources, eg fisheries, when large volume wastes such as tailings are placed on the seabed, and by the extraction processes from marine mining. Worldwide monitoring of such effects for the past 30+ years now provides information to describe Best Practice design, construction and monitoring procedures. The critical environmental factors for submarine tailings placement (STP) are the selection of an appropriate deposition site and discharge depth, the deposition rate of the tailings, and the speed of biodiversity recovery to a sustainable ecological succession. These should be predictable at new sites using current modeling and experimental procedures. Prediction procedures are still needed to minimize potential destabilization of deposited tailings, and consequent biodiversity recovery setbacks. Comparable environmental information is needed from marine mining sites.

May 1, 2002

By Bruce Geller

The 2005 Prospectors and Developers Association of Canada (PDAC) convention continued the upbeat mood found in 2004. The global mining industry is booming due to higher commodity prices in nearly every sector. Other factors include low commodity inventories, China’s strong resource demands, the weak U.S. dollar, the very strong Euro, global uncertainties, an almost overripe investment climate for natural resources and the highest mining exploration budgets in seven years. Even unglamorous commodities, like iron, uranium and zinc, received copious attention in talks, the investors’ exchange, the core shack and in certain hospitality suites. The following impressions were gathered at the convention and enhanced by conference handouts and some abstracts that are available on the PDAC’s Web site, www.pdac.ca. At least 119 papers were presented, almost twice last year’s number.

Jan 1, 2005

By D. J. Burdon, Anthony Caplan

"(1) The radiological appearances of pneumokoniosis on the Kolar Gold Field is described in detail. The characteristic abnormality is the. presence of a diffuse, fine annular and punctate mottling. (2) The frequency of symptoms could not be determined with any degree of accuracy, but it is believed that symptoms are absent and there is no incapacity until profuse radiological mottling is present, i.e., after long exposure to dust. (3) There is an increased predisposition to tuberculosis, which, if it occurs, affects the prognosismost unfavourably.(4) Pathological examination shows that the radiological mottling is due to the presence inthe lung of numerous small dust-cdll aggregates (up to T5 mm. in dia.) deposited around the smaller bronchioles and blood-vessels.(5) The dust-cell aggregates are relatively acellular but when tuberculosis is superadded thereis an excessive cellular and fibrotic reaction.(6) The difficulties of defining the radiological and pathological appearances of early pneumokoniosisare discussed.(7) The incidence of pneumokoniosis in 7,653 workmen with 5 or more years’ undergroundservice was 43-75%, but it is suggested that in future the incidence will be appreciably lower.(8) The methods of- dust production and the chemistry of mine dust are described. It isshown that the free silica-content of air-borne mine -dust is relatively low.(9) The aetiology'of the pneumokoniotic lesion is discussed."

Jan 1, 1947

By M .. Hori, H. Onishi, Y. Goda

The split-lining structure was newly developed for the air-tight lining of the underground compressed air storage cavern. This structure consists of separated reinforced concrete (RC) segments and air-tight membrane. It is most important for the Compressed Air Energy Storage Gas Turbine (CAES-G/T) system to develop the economical lining. In order to verify the applicability of split-lining structure, CAES-G/T pilot plant was constructed and operated for 6 months. We confirmed the practical usefulness and safety of this system through the operation. This paper presents the mechanical behaviour of surrounding rock mass and the lining structure observed through the operation of CAES-G/T pilot plant. Nous avons mis au point une structure de revêtement modulaire pour le revêtement des cavernes souterraines hermétiques à pression. Ce revêtement est composé de segments de béton armé et de membranes hermétiques. Il était très important, pour le CAES-G/T (Compressed Air Energy Storage Gas Turbine), de développer un revêtement économique. Afin de vérifier l’aptitude d’application de notre revêtement modulaire, nous avons construit un système pilote CAES-G/T et nous avons effectué des essais de fonctionnement pendant six mois. Ces essais nous ont permis de confirmer l’utilité et la sécurité du système. A travers le présent rapport, nous rendons compte de la structure de ce nouveau type de revêtement et du comportement mécanique de la masse rocheuse environnante que nous avons pu observer au cours desdits essais. Als luftdichter Druckbehälter wurde eine gegliederte Belagsstruktur für tief unterirdisch liegende Felshöhlungen entwickelt. Diese Struktur ist aus Stahlbetonabdeckung und luftdichter Plane aufgebaut. Bei der Entwicklung des Pressluftgasturbinen – Stromerzeugungssystems (CAES-G/T) war es die wichtigste Aufgabe, einen wirtschaftlichen Belag zu entwickeln. Deswegen wurde zum Nachweis der Effektivität der gegliederten Belagsstruktur eine Pilotanlage errichtet und 6 Monate lang betrieben. Durch den Betrieb konnten wir die Praktikabilität und Sicherheit des Systems bestätigen. Dieser Aufsatz ist ein Bericht über das Verhalten der durch Betrieb der CAES-G/T Pilotanlage beobachteten Belagsstruktur und umliegenden Felsmasse.

Jan 1, 2003

The Wednesday Morning Session of the Rocky Mountain Coal Mining Institute was called to order by Albert Keenan of the Thompson Creek Coal and Coke Company, Denver, Colorado, in the absence of the President. He introduced Edward Prostel of the University of Wyoming Natural Resources Research Institute, Laramie, Wyoming, who spoke on "Coal Utilization Work at the University of Wyoming." (Please refer to the index for printed text of the paper.) Following Mr. Prostel's talk, R. Park Lamborn of the National Mine Service Company, Pittsburgh, Pennsylvania asked Mr. Prostel two questions: (1) What -has been done in tar research? and (2) Has there been large scale research on brickets? Mr. Prostel stated that he could not say too much about the first question as this research was done in the petroleum department and he would prefer to have a chemist talk about it. As to the second question, the system of carbonization is a big project. There are many possibilities. At the University they are trying to do that in the same unit that produces the char. This system was introduced in Canada. The brickets are bound with sulphite liquor. Mr. Schloss asked Mr. Prostel to report on a project that they have been working on at the University, and Mr. Prostel stated that some time ago they began to experiment to see if it would be economically possible to dry coal at the mine (coal containing 30% moisture) and then ship it a distance of 130 miles to be used. Results are that it would be possible, but will require a considerable quantity. He felt it might be possible to operate such a scheme in a few years.

Jan 1, 1957

By Peter Zhang

The immediate roof at the test site consisted of laminated clay shale that is likely to be susceptible to weathering. With seasonal dry-wet cycles in the mine ventilation air, the roof in the intake air would deteriorate and lose integrity over time. In many instances, the weathering-prone roof would gradually scale off piece by piece between bolts and over the entry corners. In some long-term entries, roof weathering could develop up to 2-3 ft deep with columns of bolted roof hanging under the upper intact roof. If wire mesh is used, the roof bags down and reduces the entry height, and the weight of the bagged roof tends to pull the bolts out and poses a safety hazard. An effective measure is always sought to support this type of weak roof that is sensitive to moisture degradation. One solution is to seal the roof shortly after entry development to prevent moisture penetration so that roof integrity can be maintained for the long term. In this application, a polymer-based sealing material was tested in the Rockspring mine for weathering protection and reinforcement. The material is a one-component polymer powder for spray application onto the roof and rib. The sealant material is mixed with water in the spraying nozzle to apply to the roof and rib as a paste. The product sets within 5-10 minutes and forms a membrane as thin as about 1/8-in. The membrane will quickly develop tensile and bonding strength within minutes and completely cure within a few days. Through sealing, bonding and lateral reinforcement, the integrity of the weak roof can be maintained. The material has been tried in a long-term evaluation over several months in a set of main entries in the Rockspring mine owned and operated by Rockspring Development, Inc., affiliate of Foundation Coal. Preliminary evaluation has shown that the material is an effective and economical solution to ensuring the long-term stability of weathering-prone roof.

Jan 1, 2009

By R. A. Hatch

The United States depends mainly on foreign imports, principally India, for an adequate supply of sheet mica suitable for its many uses in the electrical and electronics industries. Sheet mica has, in fact, played an indispensable role in developing these industries,4/ and, in turn, the products of these industries (radio, radar, electric motors, and many others) have become indispensable to the military forces. Because or these conditions, sheet mica in its better qualities long has been classified as a strategic and critical material, and from this stems the wide-spread interest in substitute materials of which synthetic mica is one potential type. The United States Departments of the Navy and the Army entered into a cooperative agreement with the Bureau of Mines in 1947 to study ways and means of synthe-sizing and growing mica crystals. This is one of a series of reports5/ that describe the results of this program.

Jan 1, 1956

By Phil Pennington, D. Jack Adams

Mining and processing of minerals, metals, and fossil fuels can release selenium and arsenic into wastewaters. Both selenium and arsenic are difficult to remove to levels that meet current drinking water and discharge criteria. These metalloids can be used as electron acceptors by microorganisms transforming them back to reduced states, thus removing or stabilizing them. Bioremediation cost effectiveness will be discussed in terms of site information required, microbial populations, co-contaminants, pH, redox, and nutrients. Full-scale, economical ex situ and in situ biotreatments are possible and can produce 1,000’s of times less sludge than conventional precipitation technologies.

Jan 1, 2005

By J. A. Meech

"The technology known as Expert Systems is being used within the minerals industry in a wide variety of problem areas. Applications include diagnosis, prediction, training, monitoring and control. Expert Systems provide a way to program computers to imitate human thinking. The construction of such systems is a straight-forward task that can be quickly learned by novices but can require a lifetime to master.To assist in the understanding and utility of this technology, a special manual bas been prepared which operates on a microcomputer under the MS-Windows environment. The manual covers all aspects of Artificial Intelligence of relevance to Expert Systems. A hypertext system allows users to probe as d•~ply as needed to achieve understanding or to simply skim the surface of the knowledge to obtain a quick overview of subjects. The manual was developed under the sponsorship of the Mineral Sciences Laboratory of CANMET and is available from the Mining and Mineral Process Engineering Department at the University of British Columbia. Annual updates are planned to keep abreast of new developments in this rapidly changing technology. RESUMELa technologie: des Systèmes Experts est utilisée par l'industrie minière pour résoudre une grande variété de problèmes. Les domaines d'application comprennent le diagnostic, la prédiction, la formation, la surveillance et le contrôle des procèdes. Les Systèmes Experts permettent d'écrire des programmes d'ordinateur qui imitent le processus de la pensée humaine. La construction de tels systèmes e:st une tâche qui peut être apprise rapidement mais qui peut prendre des années à maitriser.Pour aider à mieux comprendre et utiliser cette technologie, un manuel spécial opérant sur microordinateur dans l'environnement Windows a été développe. Le manuel couvre tous les aspects de l'intelligence artificielle qui concement les Systèmes Experts. Un système ""hypertexte"" permet à l'utilisateur d'étudier un sujet en profondeur ou de simplement couvrir une grande variété de sujet en surface. Le manuel a été développe avec l'aide financière du Laboratoire des Sciences Minérales de CANMET et est disponible au Département de Génie Minier et Minéralurgique de l'Université de la Colombie Britannique. Des mises à jour annuelles sont prévues de manière à couvrir les changements et nouveautés de cette technologie en évolution."

Jan 1, 1993

By Abhiram Shankar

Construction projects are becoming more demanding both in terms of time and complexity. This necessitates intricate planning and sequencing of activities at the macro and micro level and continuous flow of resources across the project in order to achieve planned targets. Work and Resource planning need to be done in such a way that limited resources give optimal output. Currently dominant activity-based scheduling techniques like Critical Path Method (CPM) and Program Evaluation and Review Technique (PERT) do not model work-flow or resource-flow through a project life cycle. An extension to the conventional activity based planning is Location Based Management System (LBMS). LBMS has been explored and utilised in the case of repetitive and cyclic projects such as high rise buildings. This study focusses on the application of LBMS to repetitive and non-repetitive components of Power Transmission and Distribution (PT&D) projects involving construction of substation and cable laying. This paper presents the findings on comparing the current planning practice for cable laying with an LBMS based approach. A key finding of the study was that the conventional practice resulted in a schedule with several coordination issues that could not be identified in the planning reports. Using the LBMS based approach these issues could be identified and decisions required for resolving these could be made.

Aug 1, 2013

By T. A. Rundle, K. Kim, W. M. McCabe, E. C. Gregory

Overcoring tests were conducted at the Near-Surface Test Facility(NSTF) to assess the suitability of five techniques (U.S. Bureau of Mines borehole deformation gauge (BDG), Commonwealth Scientific and Industrial Research Organization (CSIRO) hollow inclusion stress cell, Luleå triaxial gauge (LuH gauge), and Council for Scientific and Industrial Research (CSIR) doorstopper) for in situ stress determination in a closely jointed basalt. This effort is in support of the Basalt Waste Isolation Project, which is studying the feasibility of locating a nuclear waste repository in the basalts of the Hanford Site in southeastern Washington. This paper presents the results from the overcoring study that formed the basis for selection of two techniques to be used during the further exploration of the basalt formations at depth.

Jan 1, 1983