Search Documents

By Jianguo Yin, Wenqiang Yang, Xiaoli Yuan, Juan An, Wentang Xia

Low grade iron ore with phosphorus (LGIOWP), a raw and wasted industrial solid material was used as an adsorbent to remove Pb(II) from wastewater. The effects of initial pH value, adsorptive time, initial Pb(II) concentration, adsorptive temperature and LGIOWP dosage on the Pb(II) removal efficiency were studied. The results show that the Pb(II) removal efficiencies exceed 99.4% and Pb(II) concentrations are less than 0.30 mg/L under the conditions of pH value 7.0, adsorptive temperature 50 oC, adsorptive time 30 min, initial Pb(II) concentration 100 mg/L, particle size <0.25 mm, adsorbent dosage 5 g/L and stirring speed 260 r/min. After Pb(II) removal reaction, the Pb(II) concentrations of wastewater completely accord with the requirement of national discharge standards of pollutants from lead and zinc industries (GB 25466-2010) (TPb= 0.5 mg/L) in China. Therefore, it can be concluded that LGIOWP is a new low-cost adsorbent which is suitable for the adsorption of Pb(II) from wastewater.

Jan 1, 2015

By H. H. Kellogg

The Process Fuel Equivalent (PFE) for nine different flowsheets for production of anode copper from sulfide concentrates has been evaluated and compared for a set of uniform conditions and a "standard" concentrate analysis. The processes considered are: reverberatory smelting, (wet-charge and hot-calcine charge), electric furnace smelting, Outokumpu flash smelting (2 versions), mom flash smelting, Noranda Continuous Process (2 versions), and the Mitsubishi Continuous Process. The energy required for the numerous processes auxiliary to the principal smelting processes-¬roasting, drying, air compression, gas handling, dust collection, slag cleaning, acid manufacture, etc.--are separately evaluated and incor¬porated into the process comparisons. The factors in process design that lead to important energy savings are: use of fuel rather than electric energy; use of oil or coal rather than natural gas; maximum use of oxygen enrichment of the process air; drying of charge before smelting, or, even better, drying and preheating of charge by partial roasting in a fluid-bed; recovery of waste heat from all major hot process gases.

Jan 1, 1976

By R. J. Wesely

The paper describes the various methods which are currently being used or considered to refine gold and silver. These methods are then compared on a technical and economic basis. Conclusions are drawn on the factors which might influence the choice of process for different feed stocks and economic constraints

Jan 1, 1990

By Joseph Gambogi

In 1998, approximately 57,000 tons of titanium metal was consumed in the form of mill products (1). Only about 5% of the 4 million tons of titanium minerals consumed each year is used to produce titanium metal, with the remainder primarily used to produce titanium dioxide pigment. Titanium metal production is primarily based on the direct chlorination of futile to produce titanium tetrachloride, which is then reduced to metal using the Kroll magnesium reduction process. The use of titanium is tied to its high strength-to-weight ratio and corrosion resistance. Aerospace is the largest application for titanium. In this paper, we discuss all aspects of the titanium industry from ore deposits through extraction to present and future applications. The methods of both primary (mining of ore, extraction, and purification) and secondary (forming and machining) operations will be analyzed. The chemical and physical properties of titanium metal will be briefly examined. Present and future applications for titanium will be discussed. Finally, the economics of titanium metal production also are analyzed as well as the advantages and disadvantages of various alternative extraction methods.

Nov 26, 1999

By Vasil Kopaleishvili

The bainitic Fe-C-Si alloys with optimum content of retained austenite serve as ?containers? for storing of hydrogen. Both the vacancies of fcc lattice and the possibility of forming hydrides of silicon and other alloying elements will be used. The idea is based on our scientific hypothesis. There is the silicon threshold (Si=0,50%) in "Fe-Si" system and Fe-C bainitic alloys, above which it causes self-organized phenomena: sudden increase of hydrogen solubility and amount of retained austenite in the alloy after ??ß transformation, formation of two supersaturated solid solutions <a??r>, "rejuvenation? and its reverse process. Rapprochement of iron atoms when Si=0,50%, causes appearance of new covalent forces where uncompensated electrons of 3d-subshell are involved and it provokes synergetic phenomena. They ?free? silicon atoms from the previous bonds. After that silicon itself becomes a getter of hydrogen using vacancies (14) of 3P2(6)d0(10) subshell and it results in sudden increase of hydrogen solubility in metal. Simultaneously sudden decrease of iron activity takes place. That in its turn ?releases? the carbon. Thus, its redistribution, controlling the bainitic transformation, is hastened. It stipulates for creation of ?brittle bainite" B[a(C,H)+?r(C,H)] after ??ß transformation. While weathering of metal, "rejuvenating", hydrogen diffuses in ?islets? of retained austenite and ?relaxed bainite? (B[(C)+?r(C,H+H)]) is obtained. When heating austenite ?(C,H) is obtained, and after cooling ?brittle bainite? is obtained, etc. Presented scientific hypothesis explains the available experimental facts ("rejuvenation? and its reverse process, graphitization, weldability, forming of flakes, reaching high strength, etc.) in a new manner, as well as, gives real opportunity for creating of new trends in many fields, e.g. iron based HAA. Provisional data having been obtained are encouraging.

Jan 1, 2006

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes? are considered one of the most promising alternatives to well-established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic-containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment-technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (000). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By Patrick R. Taylor

In the search for the development of more "environmentally friendly" and more intensive waste disposal approaches to meet more and more stringent environmental regulations, thermal plasma-based processes are considered one of the most promising alternatives to well- established technologies such as incineration. This paper presents an overview on the research and development status of thermal plasma-based waste remediation technologies. The properties of thermal plasma are described. Due to its unique feature of high-energy intensity and super high temperature, thermal plasma is particularly capable of destroying organic- containing wastes. Its potential and promising application to waste remediation may include: treatment of incinerator ashes; metallurgical dusts (especially, electric arc furnace dust); medical wastes; radioactive wastes; and other Resource Conservation and Recovery Act (RCRA) listed hazardous wastes. Many research institutes and vendors have been involved in the development of thermal plasma-based waste treatment technology encouraged by the cleanup programs supported by the Environmental Protection Agency (EPA), the Department of Energy (DoE) and the Department of Defense (DoD). More recently, thermal plasma-based waste treatment technologies (sometimes called plasma-enhanced pyrolysis) are focused more and more on not only just destroying organic wastes but also on how to practically, and economically recover energy contained in the organic waste materials in addition to the recovery of metals in order to offset the high operating costs.

Jan 1, 2003

By Xingjian Gao

The mechanical properties of a low carbon low alloy steel in the austenite and _-ferrite regions have been examined by thermal-tensile tests using a Gleeble-1500D system at temperatures in the range 600oC to 1300oC and at a strain rate of 10-3/s; these being the conditions that apply to the unbending operation during the continuous casting of steel. The yield strength and tensile strength of steel decreased with increasing test temperature and the embrittlement zone occurred in the temperature range 800oC to 970oC. In the embrittlement zone, the fracture surfaces and microstructures of the tensile specimens were examined by scanning electron microscope. The results showed that the cause of the embrittlement at 950oC in which the minimum %R of A was around 36% is the second phase particles precipitated along the _ grain boundary during deformation leading to inter-granular brittle fracture.

Jan 1, 2010

By Elias Rigopoulos

In the present study the reductive behavior of dust from the rotary kilns (RK), in ferronickel production from nickeliferous Greek laterites, is investigated. The study concerns dust of various origins (washing towers, electrostatic filters, polycyclones) and pellets made from the dust. Reducibility was studied in the temperature range of 700 °C to 850 °C in a laboratory tube furnace. Experimental results showed that reduction degree increases with temperature up to about 800 °C. The rate of reduction is great during the first minutes, giving a reduction degree R% equal to about 25%, in only a few minutes. After this, the rate is decreasing until it diminishes to zero after about 10-20 minutes of reaction. Maximum reduction degree achieved is 26 to 28%. Rates and reduction degrees at various temperatures are higher for the dust samples than those of the respective pellet samples. Keywords: Ferronickel, metallurgy, laterites, pellets, reduction

Jan 1, 2004

By Albert Wraith, Thomas Price, Wayne Boyd, Skip (I. E. ) Hills, Cameron Harris

Most Peirce-Smith converters inject air through tuyeres, with nitrogen representing the majority of gas passing through the process. The nitrogen controls the temperature of the vessel by carrying away heat from the reactions, both globally and locally at the tuyere tip. However, nitrogen adds energy to the bath and contributes to splashing and limits the blowing rate. High oxygen smelting has made streams of gas containing high concentrations of sulphur dioxide commonplace, which can be used to substitute SO2 for nitrogen and drastically changes Peirce- Smith converting (and all other smelting/converting processes as well). Less SO2 is required to carry away the same quantity of heat, which allows higher concentrations of oxygen and leads to the possibility of increased production. The paper investigates this substitution, its impact on converter productivity, and on the remainder of the plant. 181

Jan 1, 2009

By David Melgaard

A significant emerging recycling, waste minimization problem stems from legacy waste from the nuclear weapons program and from production of power using nuclear fuel. Premium quality metals used in nuclear plants become contaminated, making them unsuitable for reuse. Consequently, decontamination studies were conducted to evaluate the decontamination capacity and partitioning effeetiveness of Electroslag Remelting (ESR). Eight laboratory melts were conducted to evaluate the efficacy of using ESR to transport radionuclides from the liquid metal phase to the liquid flux or slag phase. To determine the decontamination effectiveness, several surrogate compounds for uranium, plutonium and other fission products were added to the melts. During the melts, the melting rate was varied, typical slag additives were used, and two different slag compositions were evaluated. The resultant post-test ingots and slag were then analyzed to determine the partitioning of the surrogates. ESR generally proved very effective in removing contaminates from the metal with a few noted exceptions. -

Jan 1, 2003

By Yotamu Hara, Animesh Jha

"High Curie temperature and large magnetic anisotropy make cobalt an important magnetic material for power engineering applications of magnets operating above ambient. It is also an essential constituent of modem lithium - cobalt oxide batteries, without which modem electronic gadgets will be functionless. Both these applications of cobalt save energy and reduce C02 emission. Ironically, however the production of cobalt from copper and nickel smelting in the world remains one of the least energy efficient process. The paper analyzes the energy balance, material and process chemistry of overall cobalt recovery and the waste generated, which entail the process limitations. We discuss a novel approach for the reduction of sulphide minerals with CaS04, permitting better separation of metals from slag and generating higher concentrations of S02. Such an approach may seem to be an alternative energy efficient option for processing and further purification of cobalt in metallic form. The results are discussed in the context of process thermodynamics and reaction kinetics for Coalloy production.IntroductionCopper sulphides bearing minerals are predominantly associated with iron and cobalt sulphides minerals. Carrollite (CuC02S4) is a mineral that has both copper and cobalt sulphides [1,2], which may also contain FeS, by substituting either Cu2+ or Co2+ ions in mineral lattice. On smelting copper - cobalt - iron sulphide concentrates, some parts of the cobalt often partition to matte at preferentially low oxygen potential by forming eventually an alloy phase with copper, however a significant fraction is often lost into an oxide slag rich in iron and silica. The slag heaps accumulated in the Copperbelt region in Zambia from last 60 years of mineral processing and metal extraction is reported to be 0.3 to 2.6 wt% of cobalt element, which is high [3]. Cobalt is also available in smaller concentrations in the copper smelting and converter slag, as reported in the investigations on the recycling of such slag materials using leaching with ammonium salt [4], iron chloride [5], and sulphuric acid [6], and solvent extraction [7].The recovery of cobalt from slag, irrespective of the techniques researched so far, does not seem energy efficient because the molten slag at 1300°C is quenched by losing thermal and chemical energy. The quenched slag is again reheated to above room temperature for leaching and above liquidus for carbothermic reduction of residual cobalt oxide. For example, in Mintek DC arc smelting [3], 80% of cobalt and 95% nickel are recovered by expending 600 kW per tonne. Assuming that the mineral carrollite is the starting phase, the univariant calculations for the Co-Ca-Si-S-0, Fe-Ca-Si-S-0, and Co-C-Si-S-0 systems are shown in Figure la, lb, and le, respectively at 1573 K."

Jan 1, 2012

By A. Mukhopadhyay

Gas stirring, simultaneous arcing, chemical additions are some basic steps in the secondary steel making. From tap to team however, there are enough uncertainties and several in-situ decision making required to match the fmal composition and temperature in the given amount of processing time. Currently available control algorithms rely on overall material and heat balance coupled with a self-learning regression based tuning of model constants. In this paper we demonstrate the capabilities of Computational Fluid Dynamics (CFD) in modeling and analyzing the thermo-chemical aspects of secondary Steelmaking. These models take advantage of scientific and engineering advances in computational tools and provide almost real time speed of analysis. This can be a very effective tool for operator training, process debugging and improvement as well as new innovations. Keywords: Argon purging, Secondary steelmaking, Arcing, Ladle Furnace, Process Control.

Jan 1, 2003

By Arthur W. Cooper

This paper contains a review of the development of blast furnace? slag handling and processing technology in the Ironmaking industry over the past 30 years, with an emphasis on economic and environmental factors. The requirements and practice of air-cooling slag for use as aggregate and of pelletizing and granulating slag for use in cement manufacture are described. The operation of slag pits, slag pots or ladles, the slag pelletizer and early granulation systems are compared with the new continuous .granulation, dewatering and handling systems developed in the past decade.

Jan 1, 1992

By Burcu Ertug, Necip Ünlü

"On average, one out of two glass bottles coming on to the market is provided by recycling processes in Europe. Glass recycling has been started by the early of 1970s in Turkey, and the recycling amount has been reached to 70 thousand tons recently, while 4.2 million tons which represents only 25 percent of total glass manufactured, is the amount of glass collected annually for recycling in the world. The glass recycle process basically involves collecting, sorting, then crushing and grinding after which glass cullet is produced as the secondary raw material. Removing of the contaminants from the glass cullet, and then melting are the next steps. In this study, recent developments of 100% recyclable without any deterioration in quality, and never decomposable glass, are discussed detailed in terms of glass production processes.1.IntroductionIn many countries, waste glass constitutes a large proportion of solid wastes, and recycling the glass is a major environmental problem all over the world [1]. Among the diverse types of waste, glass is one of the most valuable recycling materials because it can be revived and recycled completely and hardly decomposes [2]. Between 80% and 85% of the mass output from the worldwide glass industry is either in the form of containers for the food, beverage, and pharmaceutical industries, or flat glass for building construction or for motor vehicle manufacture. Other product segments, whilst only constituting about 15% of the mass output, produce high value technical and consumer products by comparison with container and flat glass [3].In the present study, the recycling of Liquid Crystal Display (LCD), Cathode Ray Tubes (CRT) and Printed Circuit Boards (PCB) were examined. The production of glasses and glass-ceramics from glass cullet, synthesis of different compounds from recycled glass were other subjects of interest. The use of recycled glass for construction industry and using glass as aggregate were emphasized. Finally the recovery of glass fibers were investigated."

Jan 1, 2012

By Payman Roonasi

Having knowledge of mechanism of magnetite formation is essential in a number of industrial processes including magnetite synthesis and corrosion of iron. In this study, magnetite nanoparticle was synthesized via two different ways; coprecipitation of iron (II) and (III) and oxidation of ferrous hydroxide. The samples were characterized using X-ray diffraction (XRD), Mid-Far IR spectroscopy, scanning electron microscopy (SEM), chemical analysis for determination of Fe II/Fe III ratio and ICP-MS for iron isotopic ratio (56Fe/54Fe) measurement. Since fractionation of iron isotopes depends on reaction rate and bonding strength, interpretation of the isotopic data with respect to the possible mechanisms is discussed. No fractionation of iron isotopes was observed for the magnetite synthesized by coprecipitation, whilst magnetite formed from ferrous hydroxide showed higher abundance of 54Fe compared to 56Fe in the beginning of reaction, implying the significance of the following reaction:

Jan 1, 2009

By Jean-François Boulanger

The production of rare earth elements from ore usually consists of three steps; the separation of a concentrate of REE bearing minerals; the cracking of the REE minerals to liberate the REE into an aqueous solution and separation of REE into individual elements. This paper describes the results of laboratory tests conducted on a carbonate-rich REE ore containing bastnaesite and monazite. The tests cover the whole processing sequence of beneficiation, preparation of the REE solution using a caustic leach followed by acid leach to break monazite and bastnaesite and liberate REE into an aqueous solution and the partial separation of the REE using solvent extraction. Details on the product quality and process performances (recovery and impurities removal) are given for each studied step. The paper also discusses the economic advantage of separating the REE rather than producing a mixed REO product to be sold to a refinery for REE separation. A mini-pilot plant version of the process is currently planned.

By François Larouche

Since their commercialization in the early 1990s, lithium-ion batteries (LIBs) have become ubiquitous for powering a myriad of portable electronics. Their usage now extends to the automotive industry and stationary energy storage market. With an average life of 6.2 years and the strong demand, the volume of spent LIBs has increased exponentially, making recycling mandatory. Currently, recycling/ recovery of spent LIBs is limited in comparison to all other types of batteries. The current processes focus mainly on the recovery of the most valuable metals such as cobalt and nickel, leaving lithium and phosphate in a low value end-product. It is necessary that new advanced recycling technologies are developed for the recovery of spent LIBs both from an economic and environmental perspective. In this paper, the current R&D status of LIBs recycling is reviewed with the emphasis placed on hydrometallurgical processing opportunities for Li-ion and Li-solid state batteries.

By R. Ressel

Keywords: ferrovanadium, thermodynamics, phosphorus Recyclable material is rapidly gaining in importance as a source of raw materials in industrialized countries. This is also the case in the production of ferrovanadium, where, increasingly, materials such as discarded capacitors, spent catalysts, slag, dust and sludge are used. As the V-content in the raw material varies greatly, the demands on process technology are very high. The share of perturbing elements depends very much on the source of the raw materials, which, in turn, makes a corresponding optimization of the various refining steps necessary. The raw materials are mostly available as oxides, which means that carbon, silicon or aluminium are used as reducing agents. Thermodynamic calculations were used to show especially the behavior of vanadium and phosphorus at different process conditions.

Jan 1, 2005

By William A. Enrico

Umicore acquired the Pirdop Smelter in a privatization offering by the Bulgarian government in September 1997. Since that time, an investment program has been conducted to increase capacity to 225 000 tons per year of anode copper, while improving the environmental performance to meet Bulgarian and European standards. A significant part of this investment program involved reconstruction of the three Peirce-Smith converters and the associated gas handling system. During the period June, 2000 through April, 2002, converter capacity was increased, the existing water-cooled hoods were replaced, the waste heat boiler was replaced by two evaporative coolers, the dry ESP&apos;s were rebuilt and extended, and a Converter Control System (CCS) installed. From 2002 until the present, a continuous improvement of operating and environmental performance has been achieved. This paper will describe the converter reconstruction project, the operational, maintenance, and environmental improvements achieved since then and additional projects presently under consideration.

Jan 1, 2005