Search Documents

By Michael P. Heisel

Solinox is a physical scrubbing process capable of removing a number of noxious materials from off-gasses, especially SO2, hydrocarbons, halogens, heavy metals such as dust, etc. As these materials are dissolved physically, (not chemically bound), the solvent is absolutely stable and no by-products are formed in the scrubbing cycle. The process has? been installed in three plants up to now, treating from approximately 30 MMSCFD to approximately 100 MMSCFD. These installations are in a non ferrous metal smelting operation, in a cellulose factory, and in a roasting process.

Jan 1, 1992

By N. R. Green, N. J. Humphreys, D. McBride, T. N. Croft, M. Cross, D. M. Shevchenko

"Centrifugal casting offers a route to high quality products in difficult to cast high temperature low superheat alloys and thin section molds. Under centrifugal forces metal is forced into thin sections and can fill thicknesses of less than a millimeter. However, due to the high liquid metal velocities there is a high risk of surface turbulent flow and air entrainment within the liquid metal. The combination of interacting flow-thermal-solidification phenomena and associated defects is a challenging modeling task which the authors have previously described and validated. Capturing the metal-air interface, on what are inevitably complex three dimensional geometries, results in highly computationally expensive simulations and simulating a single cast can take weeks on a single processor. This contribution reports on modeling a complex centrifugal cast, gas entrainment, bubble transport and solidification, employing meshes of up to a million elements and investigates the scalability of the model on high performance clusters.Introduction The ultimate goal of any casting procedure is to produce a defect-free product. For difficult to cast alloys, such as Titanium, centrifugal casting has a number of advantage over conventional gravity methods [1]. In the casting of thin sections, such as turbine blades, the metal is forced into the thin sections under centrifugal forces. The centrifugal force can overcome the backpressure due to surface tension and the metal can fill mould sections with thicknesses substantially less than a millimeter. However, the materials used in these castings [2] tend to be highly reactive and requires low superheat. High liquid metal velocity gives rise to a high risk of free surface turbulent flow and of associated entrainment through free surface turbulence [3] and trapping of gas present in the flow [1]."

Jan 1, 2012

By A. Filzwieser

The highest current density suitable for the electrowinning process is between 50 to 60 % of its limiting current density. One of the most important influences on the limiting current density is the thickness of the hydrodynamic boundary layer near the electrode surface. Therefore, the fluid flow in a copper electrowinning cell is calculated. The numerical simulation - using the CFD-software package FIRE® - considers all three different types of the fluid flow, namely, the natural convection, the forced convection by electrolyte circulation and the forced convection by electrochemically induced gas stirring. The simulation of natural convection is based on the different density values in the boundary layer at the electrode surface given by a density/concentration correlation. The copper concentration - linked with the current density by Faraday law - is solved by an additional transport equation. The simulation of the forced convection by the electrochemically-induced gas stirring is done by using a real two-phase calculation. That means that all differential equations are solved again for the second phase. The numerical solution of the fluid flow field is compared with the results of LDA- measurements, which were done in a special cell. The software for the LDA enabled a calculation of the void fraction possible and therefore a rough estimate of the mass transfer coefficient through the prevailing gas bubble induced convection can be made by assuming the influence of relative bubble volume.

Jan 1, 1999

By Naoki Hiroyoshi

It is generally accepted that ferric ions are effective for leaching chalcopyrite as an oxidant and ferrous ions contribute to the leaching only as a source of the oxidant ferric ions. However, this paper shows that ferrous ions are more useful for leaching chalcopyrite than oxidant ferric ions in sulfuric acid solutions in air at ambient temperatures. Leaching experiments and dissolved oxygen consumption measurements were carried out with a very pure chalcopyrite and 0.001 - 1 mol dm-3 sulfuric acid solutions containing 0 - 0.1 mol dm-3 ferric or ferrous ions at 303 K. Chalcopyrite oxidation with dissolved oxygen was promoted by ferrous ions but suppressed by ferric ions. As a result, the amount of extracted copper was larger with ferrous ions than with ferric ions. Effects of Thiobacillus ferrooxidans on the ferrous promoted chalcopyrite leaching were also investigated and discussed based on the experimental data.

Jan 1, 1999

By Deepak Malhotra

Rosario Dominicana, S.A., operates a gold processing complex at Pueblo Viejo, northwest of Santo Domingo (Dominican Republic). The plant processes approximately 10,000 mtpd of oxide gold-bearing ore with a work index of 11 kWh/mt. The ore hardness has increased to about 17 kWh/mt. Metallurgical auditing of the plant was conducted? to find ways to modify the circuit to process hard ore without sacrificing throughput. In addition, unit operations were optimized to increase recovery and reduce operating cost,. The results of modifications made in the plant are discussed in this paper.

Jan 1, 1989

By Jannie S. J. van Deventer

Geopolymers are novel engineering materials with the potential to play a highly significant role in the transformation of the construction materials and building products industry in the push towards sustainable development. These materials are formed by activation of industrial aluminosilicate waste materials such as coal ash or blast furnace slag with alkaline solutions. Geopolymers derived from coal ash can exhibit superior mechanical properties and chemical stability when compared to ordinary Portland cement (OPC). The use of waste-based geopolymers can also result in significant (up to 90%) reduction in carbon dioxide emissions when used in cement replacement applications. In addition to the formation of conventional pre-cast products, these high performance mineral binders are ideally suited to use in the encapsulation of mine tailings, immobilization of heavy metals and back-filling of mines due to their chemical stability and resistance to acid attack. A key attribute of geopolymer technology is the robustness and versatility of the manufacturing process; it enables products to be tailor-made from a range of raw material sources (waste and/or virgin) with specific properties for a given application at a competitive cost. Despite these key technical and environmental attributes, it is the ability to add significant value to coal ash or and/ or metallurgical slag waste streams which drives the commercial development and uptake of the technology.

Jan 1, 2006

By Mokka N. Rao

In this experimental investigation, the principal operating parameters of the spirals HC 1870 and HG 8/7 are determined for the hydrogravimetric separation of the friable siliceous iron minerals of the Piar Distric, Venezuela. Mineralogical characterization including optical microscopy of feeding materials and the products after separation are presented. Comparative analysis is made of effectiveness of productivity between the two spirals.

Jan 1, 1999

By Sylvain Gouttebroze, Mohammed M'Hamdi

In a previous work, a small scale Bridgman furnace has been used to study silicon bi-grain crystallization at different cooling rate. This work expands the analysis by studying the mechanical interaction between the crucible and ingot during the solidification and cooling. The thermal model is based on a 2D-axisymetric heat-transfer model. The flux histories are then transferred to the ingot-crucible 3D-model. Anisotropic Elastic and Crystal Plasticity model are used to model the silicon deformation. Four different assumptions are applied to model the mechanical contact crucible-ingot and three grain misorientations are considered. The results show the strong impact of the alumina crucible contraction on the stresses and deformations in the silicon ingot.

Jan 1, 2015

By Shubin Wang

Copper(II) and nickel(II) are often recovered from ammoniacal alkaline solutions by solvent extraction using hydroxyoxime extractants: both copper(II) and nickel(II) are extracted from ammoniacal alkaline solutions and, from the loaded organic phase, nickel(II) is selectively stripped with a dilute acid followed by copper(II) stripping with an acid of higher concentration. Since a small portion of ammonia is co-extracted with copper and nickel, the extracted ammonia should be scrubbed using a dilute acid before metal stripping. In the present study, a mechanistic model has been developed in order to support design and control of this process. The equilibrium distribution ratios of copper(II), nickel(II), and ammonia at 298 K using LIX® 84-I (active component, 2-hydroxy-5-nonylacetophenone oxime) as the extractant are successfully correlated by considering the relevant equilibria. Based on these results, quantitative prediction of equilibrium distribution ratios in the process has been made possible, and suitable conditions for the efficient separation of copper(II) and nickel(II) are discussed.

By Zhang Jianliang, Zuo Haibin, Gao Bing, Wang Zhe

"As a result of the shortage of coking coal and the quality decrease of coke, it is important to know how to make better use of highly reactive cokes. The co-gasification behavior of highly and lowly reactive coke for blast furnace is investigated. The results show that: In the middle stage of reaction, the weight loss ratio of highly reactive coke reacted together with lowly reactive coke is higher than that of it reacted individually. However, the weight loss ratio of lowly reactive coke is lower. The weight loss ratio of highly and lowly reactive coke is almost the same as that of the weighted average. The scanning electron microscope analysis indicated that the reaction degree of surface and interior of lowly reactive coke is relatively uniform with the reaction time increased. And the reaction degree of surface of highly reactive coke is obviously higher than that of interior.IntroductionIn blast furnace iron making process, coke functions as heat supplier, reducing agent, carburizer and skeleton. With development of blast furnace iron making technology, the skeleton function of coke is becoming more and more important in requirements of large scale furnace and high pulverized coal injection. High reactivity coke is usually produced by cheap coal with bad quality, and is not good for blast furnace process. The reactivity of coke is mainly determined by the coals used, and the resource of good quality coking coal is limited and is non-renewable. In order to fulfill the need of blast furnace, a lot of research have been done to improve coal matching using new kinds of coal to enlarge resource, in which coking coal and fat coal are reduced, whereas low price coal with bad caking property are used to lower the cost, and this would inevitably increase the reactivity of coke [1-4] Blast furnace iron making would still be the main stream for a predicted future, and high reactivity coke would correspondingly be used more and more, so it has great importance to study how to use high reactivity coke in blast furnace."

Jan 1, 2013

By Andreas Ludwig, Abdellah Kharicha, Menghuai Wu

"In order to demonstrate how CFD can help scientists and engineers to better understand the fundamentals of engineering processes, a number of examples are shown and discussed. The paper will cover (i) special aspects of continuous casting of steel including turbulence, motion and entrapment of non-metallic inclusions, and impact of softreduction; (ii) multiple flow phenomena and multiscale aspects during casting of large ingots including flow induced columnar-toequiaxed transition and 3D formation of channel segregation; (iii) multiphase magneto hydrodynamics during electro-slag remelting; and (iv) melt flow and solidification of thin but large centrifugal castings.IntroductionSince the Bronze and the Iron Ages, material processing, and here especially metallurgy, has got a global importance for the economic well-being of the societies. It is thus understandable that metallurgy has changed from arts and crafts into an engineering specialty, where the knowledge of centuries has lead to an enormous commercial and technical efficiency. However, increasing competition and the necessitation of energy and CO2 reduced manufacturing methods requires the improvement of existing techniques and even the development of new, alternative production technologies. On the other hand, the opacity of liquid and solid materials and the involved high temperatures makes the experimental penetration of metallurgical processes and with that the attainment of detailed process knowledge quite difficult."

Jan 1, 2012

By Munetaka Iwasaki

Nitrogen strongly affects mechanical properties of steel and therefore we may sometimes modify the various processes for its content. Numerous studies based on the results of chemical analysis of quenched samples were reported with a few exceptions of Hot Sievert method. The technique always poses a risk of uncertainty whether the true content of nitrogen in liquid metal is measured or not. In this study vacuum remelting under relatively low pressure was done to enhance gas phase mass transfer. Total pressure of the melt chamber was about 10-3 pa and electron beam heating was used. Mass spectroscopy was used for the direct observation of the rate of denitrization. Nitrogen molecules or atoms were detected by a mass spectrometer set above the melt. Continuous monitoring of the intensity of the fixed mass number may reflect the transfer of nitrogen from the melt to the vacuum. The results of the new and conventional techniques agree, both technique can be verified.

Jan 1, 1999

By Yong Hack Lee

Electric Arc Furnace (EAF) dust is generated when scraps are treated in the electric arc furnace and usually classified as hazardous industrial waste in most countries. EAF dust usually contains 15 to 25% of zinc and 3% of lead. It is usually treated in rotary kiln (Waelz process) or landfilled after a solidification and stabilization treatment. Numerous methods have been proposed as the EAF dust treatment technology, but few of them are in operation as a commercial scale except the Waelz process. Korea Zinc performed a plant test in which 600 tons of EAF dust was treated using TSL (Top Submerged Lance) technology. The TSL technology is a low cost, proven technology for processing zinc-bearing residues. The EAF dust was first de-chlorinated and fed to the TSL furnace. Finally, clean slag satisfying toxicity criteria was generated and valuable metals such as zinc and lead were recovered as fume oxide. The fume oxide was de-halogenated by sodium carbonate and sent to zinc refinery to recover zinc and lead. The recovery of zinc and lead was 90% and 93%, respectively. Most of the dioxin in the EAF dust was discomposed so dioxin less than the Korean regulation limit was detected in the offgas, which proves that the TSL technology is the best solution to treat EAF dust.

Jan 1, 2006

By J. Rajesh Kumar

The extraction equilibrium study of tetravalent platinum was carried out using tri-octyl/decyl amine (Alamine 336) and bis(2,4,4-trimethylpentyl) monothiophosphinic acid (Cyanex 302) in kerosene from hydrochloric acid media to investigate their extraction capacity, since they have different donor atoms, ?N? and ?S?. Their distribution equlibria were studied as a function of acid, extractant, diluents and temperature. The title metal shows the inverse behavior at higher acid concentrations. Extraction of tetravalent platinum increases with increase of extractant concentration. The plot of log D vs. log [Extractant], mol.L-1 is linear with slopes 1±0.3, indicating the association of one mole of extractant with the extracted metal species. Stripping of metal from the loaded organic (LO) with mineral acids and bases such as hydrochloric, sulphuric, nitric acids and ammonia, hydrogen peroxide, sodium hydroxide, thio- urea were studied. Regeneration and recycling capacity of Alamine 336/Cyanex 302 and extraction behavior of associated elements was also studied.

Jan 1, 2009

By Keizo Uematsu, Satoshi Tanaka, Nozomu Uchida, Anze Shui, Joaquin Lira, Cyril Lavelle, Midori Saito, Thierry Poirier

"Dispersed and flocculated alumina (non-spherical particles) slurries were prepared by pH controlling with HCL Spray-drying of these resulted in dimpled granules with a smooth surface and high density, and spherical granules with rough surface and low-density, respectively. Detailed characterization on granules and their compacts includes: SEM observation, density measuring (mercury porosimetry and Archimedes's Principle) and liquid immersion optical microscopy. Compaction of these granules originated a larger particles rearrangement in the samples made with the spherical granules than with the dimpled granules. This was verified through the orientation of alumina particles, which was pronounced in the compact made with the former granules.IntroductionOn immersing a ceramic powder in water, the surface usually acquires a charge by interaction with ionic species in solution. The charge is affected by pH and the electrolyte concentration of the water. 1 The dispersion in a slurry is achieved through the interaction of charges on the particle surface with the media. In the ceramic processing, especially in the process of casting, the dispersion of slurry has been one of the most important topics studied for many years. Recently the attention is paid on its role in the pressing. The granule characteristics are governed by the dispersion state of slurry. Takahashi et al2 , Tsubaki et al3 and Walker et al4 showed that the granules from dispersed slurry were dimpled and of high density, while granules from flocculated slurry were spherical and of low density. This variation in the granules characteristics should have a marked effect on the structure of compact.This paper presents the influence of the dispersion state of alumina slurry on the granules characteristics and also on the internal structure of compacts. Different dispersion states were elaborated by adjusting pH of the slurry. In this method, the particles are dispersed or flocculated only by the effect of surface charging, and thus some secondary effect such as the steric hindrance from an electrolyte dispersant is avoided. The characteristics of granules and compacts are examined with SEM, density measurements by mercury porosimetry and by Archimedes's Principle and liquid immersion optical microscopy. This novel microscopy provides various important information on packing structure of particles, such as their orientation. 5"

Jan 1, 2000

By Patrick R. Atkins

Energy issues will have increasing impacts on decision making in all facets of society over the next few decades. Industrial users of energy and producers of products that affect energy use must be fully aware of the implications of their processes and products on the energy situation. This paper describes a model that has been developed for the aluminum industry that allows scenarios to be evaluated to gain improved understanding of possible implications for our businesses. A brief overview of the model is provided.

Jan 1, 2006

By John O. Marsden

The past fifteen years have seen a number of important developments in copper hydrometallurgy, including the commercial application of biological heap leaching of secondary (chalcocite-dominant) copper ores, the commercial demonstration of chalcopyrite concentrate leaching technology using pressure leaching and biological processes, and the application of novel configurations of solution extraction circuits. Significant emphasis is now being placed on the development of effective stockpile leaching practices for primary ores (chalcopyrite and bornite-dominant mineralization). Some of these developments have been highly successful, and will pave the way for further development and commercialization. Others have been less successful. These developments are reviewed in the context of the metal price cycle and trends for the future are identified.

Jan 1, 2006

By Jun-ichiro Yagi

A mathematical model has been developed for simulating the blast furnace operation with carbon composite agglomerates charging based on multi-fluid theory and reaction kinetics. In this model, the behaviours of carbon composite agglomerates are considered on the basis of previously reported conservation equations and experimental research on the reduction rate of carbon composite agglomerates. A series of calculations are performed to examine the effect of charging carbon composite agglomerates. The model calculation gives two-dimensional distributions of process variables and information on the overall operational parameters. It reveals that in-furnace temperature levels significantly decrease and the reduction of carbon composite agglomerates is retarded with carbon composite agglomerates charging ratio. The furnace performance is remarkably improved with the increase in carbon composite agglomerates rate. The productivity tends to increase while coke rate and total reducing agent rate show decreases at the different degree.

Jan 1, 2006

By V. Ramachandran

ASARCO Incorporated, a large and diverse producer of non-ferrous metals, is involved primarily in smelting and refining of copper and lead. The Company also recovers by-product metals and chemicals produced in the smelting and refining process including selenium, tellurium, silver, gold, platinum, palladium, bismuth, antimony oxide, lead-antimony alloys, and nickel sulfate. The treatment of complex concentrates, containing high level's of impurities, also results in the production of various sludges, drosses, dusts and slags. This paper addresses the interplant and intraplant transfer of these materials between the copper and lead circuits and their subsequent treatment for maximum metals recovery. It also describes the role of ENCYCLB/TEXAS Inc., a subsidiary of Asarco, which treats Asarco's by-products, as well as hazardous and non-hazardous wastes produced by other manufacturers.

Jan 1, 1994

By Xian-Dong Zhou, Guo-Sheng Sun, Jianzhong Luo, Hong-An Guan

"Oxygen utilization rate of the pretreatment process which adopts biological contact oxidation method for slightly polluted supply water is relatively low, less than 10%, usually lower than 3%. So the aeration amount is not determined by calculated value of oxygen demand when doing process design, but by the ratio of gas and water. The aeration way of the biological pretreatment process for slightly polluted supply water was introduced in this paper. In the foundation of the principles of mass transfer kinetic theory and experimental data, the change law of DO (dissolved oxygen) and ammonia in the aeration tank was analyzed to explore aeration method which will help to improve the overall effectiveness of handling capacity.IntroductionThere are many kinds of filler used in the biological contact oxidation process, such as flexible solid filler, composite filamentous filler, powdery clay filler, particle ceramic filler and so on. Regardless of the different forms of filler, there are a couple of common points in the function of the aeration[1,2]: (1) The aeration process in biochemical tank not only provides adequate oxygen for the biological reaction, but also plays as a role of stirring water; (2) Biochemical reactions mainly happen in the upper reaches of tank, but seldom at down-streams.This paper, from the perspective of changing aeration way, discussed the feasibility of improving the effectiveness of biochemical reactions without increasing aeration amount, which would have some leading significances for the operation and management of similar projects."

Jan 1, 2008