Search Documents

By Yue Tian, Shengqian Wang, Lifeng Zhang

This paper is to discuss the removal of non-metallic inclusions from molten steel using a high frequency magnetic field. In experiments, a certain amount of aluminum was added to the molten steel in a crucible to generate aluminum inclusions. A layer of aluminum clusters were observed close to the wall of the crucible after the electromagnetic (EM) field was imposed. Three dimensional EM field and fluid flow simulation were performed and showed that over 91% inclusions transported to the skin depth (2.31 mm) of the molten steel. The calculation of inclusion removal agreed well with the experimental observation. The separation mechanisms of inclusions from the molten steel by the high frequency EM field were discussed.

Jan 1, 2014

By K. S. V. L. Narasimhan

Recently developed high energy permanent magnets SmCo5, Sm2Co17, Nd2Fe14B offer an interesting study of magnetic phenomenon. This publication discusses briefly the evolution of these magnets and the origin of the coercive force. Atomized SmCo5 coarse particles (150 to 300 microns) exhibit unusually large coercive force contrary to the experience in cast alloys. A brief discussion of utilization of these magnets into devices is also presented.

Jan 1, 1992

By Tabbetha A. Dobbins

We report studies concerning the time frame for catalytic reactions between NaAlH4 (sodium alanate) and TiCl3 during high energy milling. Spectral features in x-ray absorption spectra were analyzed for samples milled for various times (0 minutes, 1 minute, 5 minutes, 25 minutes, and 125 minutes). A structural transition from Ti3+ to Ti0 is observed within the first 5 minutes of milling. The Ti0 structure persists for samples milled for times longer than 5 minutes?even after those samples underwent a subsequent single hydrogen desorption/absorption cycle. Samples milled for less than 5 minutes retain Ti3+. For samples milled for 1 minute, the Ti-K edge position shifts from Ti3+ to Ti0 after a single desorption/absorption cycle. However, the first coordination sphere around the Ti0 absorber occurs at longer distances for 1 minute milled sample. These results hint at the formation of Ti0 pure metallic clusters upon desorption/adsorption cycling of 1 minute milled sample. Previously reported x-ray absorption spectroscopy studies have demonstrated the structural transition from Ti3+ (in TiCl3) to Ti0(determined to be TiAl3 found at the surface of the alanate powder). Aluminum deficiency on the NaAlH4 lattice is responsible for controlling hydrogen absorption capacity. These time-resolved spectroscopy studies suggest the possibility for controlling aluminum deficiency, while still maintaining titanium activation of the alanate powder, by manipulating the coordination environment of the titanium dopant during the first five minutes of high energy milling. Specifically, a possible approach to mitigating aluminum deficiency during doping would be to introduce an alternative species to which the to Ti3+ catalyst would form a metallic bond after the TiCl3 has attached at the surface of the sodium alanate powder and before the Ti3+ forms the TiAl3 intermetallic species.

Jan 1, 2006

By John Frederick Colloghon, O&apos

Bulong remains the only hydrometallurgical process plant in the world that recovers nickel and cobalt directly from high pressure acid leach (HPAL) laterite leach liquors without need for precipitation of an intermediate product (e.g. sulphide, hydroxide or carbonate). Direct solvent extraction (DSX) of both nickel and cobalt in combination with electrowinning of nickel has been operation at Bulong since early 1999. Focus in the first years has been on ramp-up and resolution of commissioning problems. More recently the focus has been on de-bottlenecking and process optimisation. A number of significant process problems have been resolved, the most difficult being the formation of gypsum in the nickel solvent extraction circuit. Sound control of process chemistry is essential to ensure the production of high quality nickel and cobalt products at the lowest possible cost. This paper describes the numerous changes and enhancements to the process chemistry and plant equipment at Bulong and discusses the importance of ore leach chemistry on downstream impurity metal removal. Potential additional enhancements to further reduce unit costs are also presented.

Jan 1, 2004

By Chi Ru?an

Sollutions of ammonium chloride, nitrate and sulfate were studied in extraction of rare earths absorbed on a low-grade, kaolilnitic ore recently discovered in southern China. The results of percolation leaching tests and the recovery of the rare-earth values from these solutions are presented.

Jan 1, 1989

By Akram Salah Eddine Belaidi, Lakhdar Azzouz, Benchaa Benabed

"The dunes sand is a material of a large availability in Algeria. This material is practically unexploited. The introduction of this material as a new element in the construction can be more relieve the domain of building, and contribute to the development of the southern regions of Algeria, which are very rich in this material. The main objective of our work is to exploit a largely available material in the Algerian south which is the dunes sand, as a material of construction in the region of Laghouat.In this study, first we investigated the effect of the curing environment and the nature of the sand on the mechanical properties of the mortar, such as; flexural and compressive strengths. Then after, we studied the durability of the mortar under cycles of wettingdrying and the chemical attack of sodium sulfate (Na2SO4 5%).According to the results, we note that the mortar of the sand mixes (river sand plus dunes sand) present the best mechanical performances under different environment of curing. In addition result of durability studies put forward that the mortar of the sand mixes is more resistant to the sulfates attack."

Jan 1, 2008

By Aline Maria dos Santos Teixeira, Francisco Manoel dos Santos Garrido, Joao Alves Sampaio, Marta Eloisa Medeiros

"Rocks for crops is a natural practice for soils fertilization which consists on adding rocks to the soil while water decomposes the rock, through chemical weathering, and gradually releases nutrients to the soil solution. This practice can be considered an alternative to the low production of potassium fertilizers in Brazil. In this context, the phonolite rock was characterized in order to evaluate its application as an alternative source of nutrients to the Brazilian agriculture. The phonolite studied is an igneous, volcanic rock with alkaline character that is chemically composed of a high grade of potassium due to the presence of feldspar minerals. In order to quantify the minerals present in the sample, characterization was carried out using several techniques such as X-ray diffraction, X-ray fluorescence and scanning electron microscopy.IntroductionBrazilian soils are generally acidic and nutrient poor due to the tropical climate in which high temperatures and intense rainfall favor a rapid decomposition of the rocks that from the soil. And as agriculture is one of the main bases of the country's economy, large amounts of fertilizer are used to make the soil productive.Although Brazil has large reserves of potassium, the demand for potash fertilizer is higher than the national supply, which makes the country dependent on fertilizer imports, especially in the form of potassium chloride. Thus, we must look for economic alternatives to traditional fertilizer [1].Stonemeal is a natural practice for soil fertilization that consists in adding basic or ultrabasic rocks to the soil so that water, through chemical weathering, decomposes the rock while it gradually releases nutrients."

Jan 1, 2011

By Sadi Medina

As it is characteristic from Custom Smelters, ENAMl Las Ventanas Smelter has to deal with different qualities and quantities of mining products from about 70 suppliers, that contain a variety of impurities that would be harmful for copper production. In order to increase the smelting capacity, an oxygen plant has been running since September of 1990. Moreover, to improve the environmental conditions, a new sulphuric acid plant started up to neutralize the metallurgycal off-gases from the Teniente Converter and partially from the Peirce-Smith converters. Based on the on-line operation among the reverberatory furnace and the Teniente Converter using oxygen enriched air to produce high grade matte, most of the volatilizing impurities, mainly arsenic, are collected as discarding compounds in the gas cleaning system of the acid plant. This paper describes the continuous performance of the Teniente Converter with acid plant, the results attained, the operation problems and how they were solved. The impurities distribution achieved in this process is also included.

Jan 1, 1993

By Line Hallgren

The fluid flow in the mold during up-hill teeming is of great importance for the quality of the cast ingot and therefore the quality of the final steel products. At the early stage of the filling of an up-hill teeming mold, steel enters, with high velocity, through the nozzle into the mold and the turbulence on the meniscus could lead to entrainment of mold flux. The entrained mold flux might subsequently end up as defects in the final product. It is therefore very important to get a mild and stable inlet flow in the entrance region of the mold. It has been acknowledged recently that swirling motion induced using a twist tape swirl blade, in the submerged entry nozzle is remarkably effective to control the fluid flow pattern in both the slab and billet type continuous casting molds, resulting in increased productivity and quality of the produced steel. From the above result, we propose, swirling flow generated through a swirl blade inserted into the entry nozzle, as a new method of reducing the deformation of the rising surface and the unevenness of the flow during filling of the up-hill teeming mold. The swirling blade has two features: (1) to generate a swirling flow in the entrance nozzle and (2) to suppress the uneven flow, generated/developed after flowing through the elbow. The effect of the use of a twist tape swirl blade was studied using both numerical calculations and physical modeling. Water modeling was used to assert the effect of the swirling blade on rectifying of tangential and axial velocities in the filling tube for the up-hill teeming and also to verify the results from the numerical calculations.

Jan 1, 2006

By Ray Y. Lin, Sunil G. Warrier

"Low cost processing of metal matrix composites is an essential requirement for this class of materials to be acceptable in commercial application. In an effort to reduce the cost of processing of metal matrix composites, an infrared pressureless liquid infiltration technique has been developed. The salient features of infrared infiltration are that it is rapid, simple and a low cost process. The rapid processing capability causes very little oxide formation on the alloy resulting in both improved wetting and flow characteristics and reduced oxygen contamination in the composite. Thus, vacuum is normally not required. Using infrared inflltration, aluminum and titanium matrix composites have been prepared under an ambient argon atmosphere. Reinforcements in these composites include carbon fibers, silicon carbide Nicalon fibers and Textron's SCS fibers. Microstructural and mechanical test results indicate that completely consolidated composites with good fiber distribution, limited interfacial reaction and high mechanical properties can be manufactured by this process. IntroductionAluminum and titanium matrix composites reinforced with ceramic reinforcements are strong candidates for numerous applications in the aerospace and automotive industries. Aluminum matrix composites are commonly fabricated by either solid state vacuum hot pressing, liquid state pressure infiltration or squeeze casting [1]. Although liquid state pressure infiltration and squeeze casting has significant advantages over solid state processes, the requirement for pressure makes these composites uneconomical for large scale industrial application. Titanium matrix composites are primarily fabricated by solid state diffusion bonding [2]. Pressureless liquid infiltration can significantly reduce the cost of fabrication in both the composite systems. However, during pressureless infiltration processes, several complications concerning the wetting characteristics and chemical compatibility arise."

Jan 1, 1994

By A. K. Kyllo

The use of Composite Furnace Module cooling systems has been shown to give improved refractory performance in a number of above bath locations in WMC flash furnaces. To test the behaviour of modules in contact with a melt, a set of instrumented modules have been installed in the reaction shaft of a. nickel flash furnace. The location was chosen to provide a suitably harsh environment to ensure rigorous testing, while still allowing relatively easy access for module installation. The modules were continuously monitored to provide information on the module performance, as well as the temperature in the shaft itself. The shaft temperature showed significant transient behaviour, which resulted in heat fluxes through the modules ranging from 10 to 92 kW m-2. The modules were capable of handling the highest heat flux with no risk of the coolant boiling. This paper details the design and operation of the modules over a period of seven weeks.

Jan 1, 1999

By E. A. Trillo, L. E. Murr, R. D. Flores, J. C. McClure, B. M. Nowak

Complex vortex and swirl-like solid-state flow phenomena have been observed in the residual microstructures characterizing the friction-stir welding (FSW) of copper to 6061 aluminum; 2024 aluminum to 6061aluminum,2024 aluminum to 1100 aluminum, 2024 aluminum to 7039 aluminum and 2024 aluminum to 2195 aluminum. These flow phenomena are characterized by intercalation lamellae composed of dynamically recrystallized grain structures of the dissimilar metals which provide a super-plastic-like mechanism for the FSW flow in the solid state; there is no melting and temperatures at the weld center do not exceed about 0.8 TM (where TM is the absolute melting temperature (K)). In experiments to be described and illustrated, optical or light metallography (LM), scanning electron microscopy (SEM) and transmission electron microscopy (TEM) techniques are utilized in examining residual FSW microstructures corresponding to tool rotation (stirring) speeds ranging from 400 to 1200 rpm, and traverse (or actual welding) speeds of 1 to 2 mrn/s.

Jan 1, 1999

By David B. George

In spite of the many well-known problems inherent in Pierce-Smith converting, it remains the dominant copper converting process. Continuous copper converting and direct concentrate to blister smelting have been commercially available for over 25 years and now produce approximately 15% of copper smelter production. The two fully commercialized continuous converting processes, Mitsubishi MI Process and Kennecott-Outokumpu Flash Converting, and several emerging converting processes are reviewed with view of their potential, limitations, and environmental performance. Some myths regarding these technologies and Peirce-Smith converting are also challenged.

Jan 1, 2002

By Krishna Kumar

"Growth of electronics waste (e-waste) and lack of appropriate disposal mechanism are the great concern for developing countries like India. The domestic generation of e-waste in India is rapidly growing with the development. The imported substance is also substantially contributing to the e-waste inventory. Recycling of e-waste is mainly carried out in unorganized units in India. The primitive recycling technique used by the unorganized sector is a great threat to the environment and the health of the operators involved in these profession. Therefore, improvement of technology used by these units towards a cost effective, environmental friendly alternative could be the solution to the present crisis. Few initiatives of recycling have, however, come up in recent years in organized units. The precious metals are still recycled in the developed countries. This report discusses the inventory, technology status, legal legislative and existing practices of e-waste management in India.1. INTRODUCTIONInnovation, research and development in the field of electronics and information and communication technology (ICT) lead to convenient, independent human life. Consumption of electronics and hardware products has enhanced by manifold. Electronics and hardware sectors have, thus, become the fastest growing sector in the world. Faster obsolescence of these products is forcing users to replace products with an advanced technology. Life cycles of these products are few years. Discarded electronics products are, therefore, accumulating alarmingly in our society. Electronics waste (e-waste) is a crisis not only due to its volume but also for presence of its toxic ingredients, like heavy metals (e.g. lead, mercury, cadmium, hexavalent chromium) and flame retardants such as poly brominated biphenyles and poly brominated diphenyles ether. These substances create potential occupational and environmental health hazardous."

Jan 1, 2011

By Peng ZANG, Qihang Liu

Experimental work was conducted to determine the relationships of coal char conversion with temperature and heat absorption. The results show that at an earlier stage of the coke forming process, lump coal would absorb large amounts of heat but the increase of high temperature strength of lump coal was not significant. Contrarily, the lump coal’s high temperature strength was greatly improved at later stage of coke forming process. A number of residual coal was found in most tuyere coke samples illustrating that the lump coals added in the melter gasifier were not completely transformed into coke when they arrived at the tuyere region. The results indicate that the improvement of lump coal’s high temperature performance is limited in the melting gasifier by the low coke forming rate which could become the core factor of fines generation of lump coal in the melting gasifier.

Jan 1, 2016

By W. G. Davenport

Chapter 13 evaluated the %02 in blast, industrial oxygen and oil requirements for smelting FeSrCuFeS2 concentrates~ This chapter examines high eu grade CU2S-CuFeS2 concentrates the same way.

Jan 1, 2001

By Masaaki Naito

The Japanese steel industry has a long history of introducing new and innovative technologies in the field of ironmaking. The new technologies introduced during the past ten years include technologies to use cheaper and lower-grade raw materials and fuels, measures to prolong the service life of blast furnaces and coke ovens, promotion of energy saving, use of wastes and solutions to environmental problems. This report outlines the condition of production and technological trends and technical development themes in ironmaking technologies.

Jan 1, 2006

By Kalathur S. Narasimhan

Powder metallurgy is a net shape process competing favorably with machining, stamping, forging and castings. The growth of ferrous powder metallurgy over the past four decades reflect the advancements in materials technology, compaction technology, sintering technologies and other related fields. This presentation gives a brief background on how materials technology evolved.

Jan 1, 2006

By W. G. Davenport

Most pre-t 988 Outokumpu flash furnaces were built with blast heaters. Many continue to use them. Blast temperatures in these smelters· are typically 400 to 700 K (Table 2. 1) This chapter: (a) shows how hot blast is included in our calculations (b) evaluates the effects orhot blast onauthothermal65% Cu matte production.

Jan 1, 2001

By Keizo Uematsu, Kumiko Sanda, Nozomu Uchida

"Full understanding of mechanical properties is the most important assignment in ceramics. Establishment of defects-property relationship is crucial for fulfilling the assignment. This study reports detailed characteristics of defects and their relevance to the mechanical properties for alumina ceramics made through a typical industrial processing. Novel characterization methods were applied to evaluate their defects. A very simple direct correlation was successfully found between defects and properties in ceramics. This result is a great epoch in the field of ceramics. IntroductionThe ceramic materials are used in refractoriness, corrosion resistant materials and structural materials. The low fracture toughness and scatter of strength are very important problems in ceramics. The toughness of ceramics is lower than metal and polymer materials, and the allowed defect size is small. Very small internal defects (pore, crack, huge particle) can be a fracture origin in the brittle fracture. The characteristics of defects such as size, distribution and shape change markedly by process condition, which cause the scatter of strength. This study conducts quantitative evaluation and direct observation of the sizes, shape and a number of internal defects with a light microscope, and discusses the relationship for mechanical properties and defect sizes"

Jan 1, 2000