Search Documents

By Karl-Michael Zett, Marcus Kirschen, Ashraf Hanna

"Bottom purging systems are well established practice in refining metallurgy and an increasingly important technology for the EAF process in steel industry. Direct bottom purging provides efficient mixing of the entire melt volume, increases turbulence intensity in the melt, and improves mass exchange of alloy additions or oxygen. Continuously rising columns of dispersed gas bubbles helps to increase removal of volatile components carbon monoxide and hydrogen avoiding boiling retardation. Direct purging (DPP) systems provide cost benefits especially for EAF processes where metallurgical constraints have to be considered, e.g. for alloyed and stainless steel production, foundries. Case studies are presented.IntroductionCurrent EAF Technology and Production Constraints in Steel IndustryApproxinlately 30 % of steel, 446 Mio. tonnes in 2011, was melted in the electric arc furnace (EAF) with increasing tendency due to its large flexibility in production volume and raw materials. With recent increase of prices for ferrous raw materials the requirements for production of high quality steels from low quality scrap, direct reduced iron (DRI) and blends of ferrous raw material in various qualities increased. Maximum yield of ferrous raw material, oxygen, carbon, and alloys and minimum energy costs are of high importance. At modem high productivity levels even small process improvements provide considerable cost savings. Such improvements are caused, e.g., by efficiency increase of mass and energy transfer in the EAF. Optimization of flow pattern in the steel bath is therefore important for efficient melting of scrap and DRI and high homogeneity of the melt [1-4]."

Jan 1, 2013

By Viktor Ashikhin, Pavel Arkhipov, Yurii Zaikov

"Lead alloys electro-winning from chloride melts was under investigation. Impurities concentration in cathode lead is strongly depended on temperature, electrolyte composition, anode current density. The equilibrium electrode potentials of lead-antimony alloys with the various content of electropositive metal in the alloy were investigated in the wide temperature interval. Thermodynamic properties of Pb-Sb alloys containing 20-95 mol% of Pb were studied by EMF method in temperature interval 723-873K in molten mixture of potassium and lead chlorides. Partial and integral thermodynamic characteristics were calculated. Small negative deviations from Raul’s law were found. Anode processes were investigated. The lead dissolution was found to be the only process in certain interval of current densities and electropositive metal content in alloy.IntroductionAt present human race is facing the problem of pollution by lead and its compounds and also the pollution influence on population health all over the world. One of the solution ways is the recycling lead containing technical wastes by ecologically clean technologies.World scientific community pays much attention to the electrolysis of molten salts. The usage of salt mixtures, as electrolytes, discovers new possibilities in the production of metals, metal compounds and alloys. ?????????? of the electrolysis at the temperature 50 - 200 °? above the melting temperature of chosen salt mixture allow to unbreaks processes, that undergo in the pre-electrode layer. The rate of the electrodepositing of elements are much higher than in the water electrolytes. At present there are technologies developed for production of metals (Ta, Nb, Ti, Zr, Hf, Ca, Al, Mg, Be, Li and others) by the electrolysis of the melts. Electrolysis of melts might be used in order to convert different technological formations containing lead and other nonferrous metals, that produced by different enterprises. According to the level of the influence on the living organisms lead is in the group of highly dangerous substances alongside with arsenic, cadmium, mercury, selenium, zinc, etc. Toxity and ability to accumulate in the human organism are two main sources of danger for the human being."

Jan 1, 2008

By Carl W. Dalrymple

A wide variety of contaminants (heavy metals, suspended solids, colloids, oils, organics) have been successfully removed from wastewater using an electrocoagulation process. An innovative electrocoagulation system is described. This process involves a procedure which subjects dissolved and suspended wastewater contaminants to the simultaneous addition of metal ions in the presence of direct current. During the treatment process Ionic and other charged particles in the wastewater are neutralized with oppositely charged ions generating the coagulation of contaminants: The process Is called CURE, and' presented here with application to wastewaters containing mainly heavy metals.

Jan 1, 1995

By John R. Hugens

Modifications in the ALSCAN method of measuring hydrogen dissolved in liquid aluminum have made it possible to monitor the level of hydrogen dissolved in liquid copper. Measurements from the tundish show a correlation with eddy current readings from the continuously cast and rolled copper rod from the continuous casting and rolling system at Amarillo. The measurements also indicate that the copper in the tundish is supersaturated with hydrogen.

Jan 1, 1994

By M. Jortikka

The smelting process of the old reverberatory furnace including its capacity has been improved over the years in different ways eg. with oxy-fuel burners, parallel reactors with the reverb or with various modifications of the reverb furnace itself. The future reverb modifications with old concepts are difficult or impossible as the increased copper losses in slag call for separate slag treatment and particularly the process modifications do not solve the environmental issues but instead mean unavoidable high capital and operating costs in gas cleaning and sulphur recovery. During the last decades improvement in process performance and increase in capacity of copper flash smelters has been achieved easily by substituting the pre-heated process air by highly oxygen enriched air. The flash furnaces of today, however, are inherently designed to operate with high oxygen enrichment. Further process improvement with a view to production costs and capacity increase as well as to the more stringent environmental requirements is possible with even higher oxygen enrichment. This, apart from the advantages it generates, requires improvements in and careful design of the feed system, concentrate burner, furnace cooling and the off-gas line as well as adaption of the flash converting instead of the conventional Peirce-Smith converters. A logical answer even for the revamping of the reverb smelters in the future is the total replacement of the reverb furnaces with flash smelting together with flash converting. This paper discusses the possibilities for future process improvements of the existing flash smelters taking into account the process concepts, equipment modifications and capital aspects not forgetting the environmental issues. The revamping of the PASAR smelter in Philippines is introduced as an example of a recent success story.

Jan 1, 1994

By Mark E. Schlesinger

A substantial database exists for the thermodynamic properties of many antimonide compounds, but these have rarely been compiled or critically discussed. An abbreviated version of a full?scale review of the thermodynamic properties of binary antimonide compounds is presented, focusing on the choice of experimental techniques.

Jan 1, 2006

The increasing need for robust pyrometallurgical furnace construction is driven by two trends in the copper and other base metals smelting industry: ? the desire for increased production within a single furnace line by greatly increasing smelting intensities, which generates high heat fluxes to the crucible. walls, and ? the operational and economic imperatives of maintaining high percentage on- line times and long campaign lives between rebuilds. A key feature of furnaces capable of producing at high rates, while containing intense processes, is a strong, thermally robust wall cooling system. Equally important design aspects include the furnace steel structure, refractories, a cooling water supply and piping arrangment for safety from leaks and disruptions, and instrumentation/controls for monitoring and rapid mitigation of process excursions. Integration of the cooling elements into these furnace systems is essential for optimum performance of the cooling elements, and indeed the entire furnace. This paper discusses the development of a composite copper / refractory water- cooled design, which has been successfully implemented on several copper smelting and converting furnaces, including Kennecott's flash converting furnace, INCO's MK reactor, and Kidd Creek's converting furnace.

Jan 1, 1999

By D. J. Brennan

A techno-economic study is in progress, examining process and product options for treating smelter gases containing various concentrations of sulphur dioxide. Key contenders have been examined within an Australian context using the following criteria: * Markets for products * Capital Costs * Operating Costs * Waste streams generated Product options considered thus far are sulphuric acid, sulphur, calcium sulphite and gypsum. The development of an appropriate overall framework for evaluating process and product options is discussed and findings thus far presented. The emerging techno-economic study offers promise as a constructive guide to future policy decisions by industry and government.

Jan 1, 1994

By Kuiting Wang, Jinshan Liu, Ninglei Sun, Aiguo Dong, Yeda Lu

"Eliminating the environmental threat caused by waste effluent containing magnesium sulfate derived from the process of nickel laterite sulfuric acid leaching and subsequent nickel precipitation is always a focus in the metallurgy field. A new flowsheet whose procedures include vaporization, crystallization, two stages precipitation of magnesium, causticizing treatment of filtrate and ammonia recycle was investigated. Both the details of the flowsheet and its application are described in this article. It is confirmed to be an effective and economical method to prevent the pollution by the waste effluent, simultaneity, a series of magnesium products recovered during the process own good economic returns.IntroductionSulfuric acid leaching is the conventional procedure of extraction valuable metals from ores in hydrometallurgy field. During the process of nickel laterite sulfuric acid leaching, several metals, including Ni, Co, Al Mn, Fe, Mg etc., migrate into the leachate in the form of soluble metal sulfate. After subsequent procedure of purification, precipitation of Ni and Co and neutralization, an enormous stream of waste effluent which contains a concentration of approx. 15-40g/L Mg is exhausted. Such solution containing magnesium sulfate is toxic, which causes diarrhea for both human and animals. On the other hand, large amount of sulfate acid was consumed during the process of leaching by the compound of Mg, which increases cost of a hydro nickel plant.In arid areas, the waste effluent mentioned above is treated via evaporate pond owning large acreage, which needs not only the appropriate meteorologic condition, but occupies much land. In coastal areas, it is directly discharged to the sea, which probably deteriorates ecological system of offshore strip. The most widespread method to treat with the waste effluent is neutralization by lime cream, the residues of which containing magnesium hydroxide and gypsum are transported to residues pool. Neutralization is a simple process, but it never recycles the Mg and sulfate anion into new application, meanwhile, the residues are potential threat to the environment."

Jan 1, 2012

By W. F. Miao

Nanocrystalline mixtures of Nd2Fe14B and a-Fe have been synthesized by mechanical milling and heat treatment. The samples exhibit isotropic behavior, with significant remanence enhancement associated with exchange coupling across the interfaces of hard and soft magnetic phases. Measurements of the effect of heat treatment on structure and magnetic behavior demonstrate the important influence of grain size on magnetic properties. The effect of alloy additions to increase the saturation magnetization of the soft phase and the magnetocrystalline anisotropy of the hard phase has also been investigated.

Jan 1, 1997

By Kazutaka Kunii

It is invariably certain that after punching for IC Leadframes, scrap metal were generated. These seraps were re-dissolved and in order to use as raw material for leadframes, it is necessary to remove the Ni plating. In this study a simple method was developed for the removal of Ni plating by surface oxidation of Ni plating. For this purpose a fundamental study was carried out on the oxidation behavior of Ni plating. Results showed that by controlling the oxidation condition, a considerably high rate of Ni could be removed.

Jan 1, 1996

By Hani Henein

"Heat transfer between droplets/particles and a gas phase plays an important role in the transport of numerous materials processing operations. These include rapid solidification operations such as gas atomization and spray forming, as well as chemical systems such flash furnaces. Chemical reaction rates and solidification are dependent on the rate of gas-particle or gasdroplet heat transport. Using a heat transport model validated using single fluid atomization of molten droplets; the effect of process variables on heat losses from droplets was examined. In this work, the effect of type of gas, droplet size, gas temperature, gas-droplet relative velocity on the heat transport from AA606 l droplets was examined. The most critical of these process variables to heat transfer is identified and will be presented.IntroductionIn materials processing, droplets are often encountered and used in processing a wide range of liquids and slurries. The small size of the droplet enables high reaction rates or high solidification rates in many systems. In order to capitalize on these high rates of transport processes, sprays are· also developed to maximize throughput. The design of these sprays, however, does not account for the transport steps and rate limiting mechanisms at the droplet surface. Rather, spray design focuses on maximizing the break-up of a stream or slurry into small size droplets or controlling the spread of the spray. Spray systems in industrial use typically generate droplets of wide size distribution leading to a wide range of reaction times for each of the droplets. Often the generation of a spray involves a number of coupled phenomena such as stream break-up, droplet-gas transport, droplet size distribution and spray geometry. Using gas generated sprays, it is not possible to identify how individual process variables contribute and control each of these coupled phenomena. While many mathematical models have been developed of sprays and they attempt to simulate coupled droplet transport, they do not provide insight into the contributions of different mechanisms in heat transfer. This is primarily because the basic fundamental heat transport between droplet and gas cannot be isolated from other gas spray phenomena experimentally such as two-way thermal coupling [l]. Thus, experimental validation of heart transfer of large and complex industrial spray models is not carried out. Hence, the validity of spray models remains in question and the approach required to optimize spray processes cannot be clearly identified"

Jan 1, 2004

By Luis G. S. Sobral, Gabrielle N. Bard

Copper sulphides Concentrates, from the flotation process of copper primary ore; contain, commonly, small amounts of precious metals, such as gold and silver. During the smelting process of those concentrate all gold and silver are practically in the blister copper, which is cast into anodes. Those copper anodes are electrorefined in an electrolytic system, where the electrolyte is an acid copper sulphate solution, where a high purity electrolytic copper is produced (>999,9/1000). The slime when submitted to an oxidative leaching process, using sodium hypochlorite and hydrogen peroxide as oxidizing agents, turn those metals into solution. This research practical work, apart from concentrating effort on the digestion of the anode slime, aims at evaluating the efficiency of the cementation process of the metals of interest for the separation of them to take place. 141

Jan 1, 2008

By Yoshio Waseda

A laser flash method has been applied to obtain the thermal diffusivity values of Zr55Al10Ni5Cu30 alloy in the liquid, glassy, crystallized and supercooled liquid states. The electrical resistivity of this particular alloy was measured in the glassy, and crystallized states by a direct current four probe technique. A specific heat of Zr55Al10Ni5Cu30 alloy was also determined by a differential scanning calorimeter in the glassy state. On the other hand, thermal diffusivity values for two alloys of Zr60Al15Ni25 and Zr65Al7.5Cu27.5 were measured in the crystallized and liquid states. The thermal diffusivity values of three Zr-based alloys in the liquid state are summarized in the linear equations with positive temperature dependency and it is noted that the lower the thermal diffusivity values of Zr-based alloys at liquidus temperature, the lower the critical cooling rate to obtain metallic glass phase becomes. The thermal diffusivity values of Zr-based alloys were compared with those of Pd-based alloy case. These results suggest that thermal diffusivity of alloy liquids might be an indicator of the glass-forming ability of Zr-based and Pd-based alloys.

Jan 1, 2006

By M. Kane, O&apos

Operators and designers require a comprehensive model to predict performance of heap leach piles and provide input of reliable and defensible data for economic modelling. A conceptual, theoretical, or numerical predictive model addressing the required metallurgical, geological, biological, and operational considerations should be developed within the framework of the hydraulic performance of the heap leach pile. It is generally agreed that segregation, compaction, and consolidation are physical aspects which significantly affect recovery and in general hydraulic performance. Hydraulic performance of heap leach piles can be described through the application of unsaturated zone hydrology. Unsaturated zone hydrology describes the flow and storage of moisture and oxygen in a porous medium under conditions where the pore water pressure is less than atmospheric. The porous material is "unsaturated" if an air phase, in addition to the water phase and solid material phase, is present. These conditions describe the operation of a copper heap leach pile. This paper will focus on developing an understanding of hydraulic performance in segregated heap leach material and demonstrating that unsaturated zone hydrology can be used as the framework to improve understanding and prediction of heap leach performance.

Jan 1, 1999

By C. I. A. John

The slag dump at ZCCM's Nkana Division contains some 16 million tomes of slag, deposited since the mid-1930's. The average cobalt grade of the slag is 0.65% with some areas as high as 3%. Current arisings of slag from Nkana Smelter also contain significant tonnages of cobalt. Intensive investigations were conducted in the past into methods of recovering cobalt from these slags, although none of the processes was developed to a commercial scale. The company is now working to develop a long-term strategy for ensuring the continuing production of cobalt at optimum levels, and the resource represented by the Nkana slags will be a major component in such a strategy. The present paper reviews the various processes which have been considered for recovering cobalt, both from the dump slag and from the current slags.

Jan 1, 1993

By Satian Niltawach

Iron sulphate jarosite through which iron in zinc sulphide concentrate feed is removed from the production circuit of conventional roast-leach-electrowin process, is chemically unstable and environmentally hazardous even if it is mixed with lime. If zinc silicate ore is used at similar chemical conditions in place of calcine in the jarosite precipitation, the resultant silico-jarosite residue having been mixed with lime is chemically stable and environmentally friendly. The recovery of zinc from silicate ore is also higher than that from calcine.

Jan 1, 1994

By R. J. Batterham

This paper sets the scene for the Australian-Asian Pacific Course and Conference on Pyrometallurgy for complex materials and wastes. The relentless presence of competitiveness is rehearsed as the source of the current trends towards continuous improvement and benchmarking. While this might be expected to lead to more spending on pyrometallurgy, the opposite appears to be the case. The paper examines the reasons and suggests that we face an increasing challenge for selective developments that can lead to sustainable competitive advantage - both in mineral and in waste processing.

Jan 1, 1994

By Roger Agnew

Sulphide ores mined by Inco Limited in the Sudbury District contain small quantities of cobalt. During beneficiation, cobalt distribution to various streams is similar to nickel. After smelting, nickel is selectively extracted by carbonyl refining and the cobalt remains in the carbonylation residue. This residue is processed in a specialized hydrometallurgical plant to produce precious metal residues, copper cathodes, and a nickel- cobalt carbonate intermediate product. The nickel-cobalt is shipped to Port Colborne where the cobalt is separated as cobaltic hydroxide and refined to metallic cobalt. This paper deals specifically with the recently constructed Electro Cobalt Refinery. The cobaltic hydroxide is dissolved and residual zinc, copper and nickel are removed by ion exchange and organics by a carbon column. The purified cobalt solution is fed to the electrowinning circuit where cobalt rounds are produced on stainless steel mandrels. In the design and construction of the refinery, special attention was directed to materials of construction both for the process equipment and the physical plant, operating control and flexibility, and the quality of the working environment. The end result is an efficient and clean operation which yields a product of excellent quality.

Jan 1, 1988

By Tatsuki Uzawa, Takashi Nagai

The consumption of Nd and Dy is increasing dramatically because of an exceptionally high demand for Nd-Fe-B-(Dy) magnets and a significant amount of the magnets are wasted. It is important to develop a recycle process the elements from the wasted magnets. In this study, Nd and Dy were extracted from the magnets by silver at high temperature. Nd can be extracted more than 70 % by silver. However, Dy is extracted only 25 % in the same experimental condition.

Jan 1, 2014