Search Documents

By Eduard Ouerra, Nuo Jin

"The use of polytetrafluoroethylene, PTFE, as a solid sorbent for elemental sulfur during pressure oxidation of chalcopyrite was investigated. The effects of agitation, PTFE particle size and lingin sulfonate addition were evaluated using leaching conditions that were otherwise similar to those employed in the CESL process. The effects of these factors and their interactions on chalcopyrite oxidation are explained in terms of interfacial forces and solid-solid interactions. Using relatively fine PTFE powder with vigorous agitation resulted in about 100% copper extraction in less than 90 minutes without the need for grinding of the flotation concentrate.IntroductionThe extraction of copper from sulfide ores has always been dominated by the conventional pyrometallurgical smelting process. Though much effort has been made to develop various hydrometallurgical processing routes, smelting remains as the dominant process, treating approximately 80% of the chalcopyrite concentrates worldwide [1]. However, some of recently emerged techniques for treating chalcopyrite through hydrometallurgical routes are showing results that are competitive with smelting in terms of economical feasibility. Representative methods include: Activox Process, CESL Process, Anglo/UBC Process, High Temperature Pressure Oxidation, and Bio-Oxidation. Among these, the CESL processes operate at a medium temperature range (typically 140-150GC) and oxygen pressure of 100 psi, with chloride as a catalyst, and reportedly achieve copper extractions of about 95% with a light regrinding of flotation concentrate to a p95 of 45 ìðé [2]. In spite of this satisfactory extraction result, the leach residues contain significant amounts of conglomerates which contain a small amount of unreacted concentrate [2], The conglomerations are formed because the elemental sulfur generated is liquid and sticky (melting point of sulfur being 119°C), and has a tendency to wet the sulfide mineral surface, a fact which inhibits the oxidation of the minerals. The overall process chemistry of the CESL process may be summarized as follows [3]:"

Jan 1, 2012

By Nedam Abed

A fundamental study of the sonochemical leaching of chalcopyrite in ferric ion media has been performed to understand and quantify the effects of sonication and other parameters on leaching reactions. The study covers sulfate and chloride media. The main leaching reaction: CuFeS2(s) + 4Fe3+(aq) Cu2+(aq) + 5Fe2+(aq) + 2S(s) (1) was found to be dependent on temperature and initial particle size, but less dependent on ferric ion concentration. Leaching kinetics were not affected by ferrous ion concentration or the amount of chalcopyrite added. Leaching was performed under a variety of sonication and leaching conditions. Reaction stoichiometry was confirmed through detailed wet chemistry analysis and mass balance calculations. The use of ultrasound activation showed a clear improvement in leaching kinetics and amount of copper extracted, sonication having a catalytic-like effect on the leaching reaction. Compared to experiments without sonication, reaction rates were 2-3 times faster at the same temperature, and could be faster by a factor of 20 for the same initial particle size. Regardless of initial particle size, the amount of copper extracted was comparable under sonication, and could be twice that under chemical leaching, implying the avoidance of fine particle grinding. Sonochemical leaching was found to be only temperature dependent, where the best copper extraction was at 75C. Leaching was further enhanced by the use of a grinding aid. The leaching behavior of chalcopyrite particles remained similar with and without ultrasound activation, implying that the known passivation mechanism in the oxidative leaching was not eradicated. Sonication resulted in coarse particle breakage (ultrasonic milling). Sonication did not contribute to particle passivation, as affirmed from different leaching procedures and sonication in aqueous and organic media. Parabolic leaching kinetics were confirmed for leaching experiments.

Jan 1, 2003

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Luciana Harue Yamane

"The present work investigated the influence of Fe+2 initial concentrations in the bioleaching of copper from printed circuit board using Acidithiobacillus ferrooxidans-LR. Printed circuit boards were collected from obsolete computers and mechanically processed through size reduction followed by magnetic separation. The bacteria Acidithiobacillus ferrooxidans-LR were grown and adapted in presence of printed circuit boards. A shake flask study was carried out on the printed circuit boards samples (non-magnetic fraction) using a rotary shaker under the following fixed conditions (185 rpm, 30°C). The bioleaching efficiency was evaluated by comparison between the concentration in the initial sample and in the leached liquor, pH of the medium and concentration of ferrous iron produced. Inductively coupled plasma optical emission spectrometry (1CP-OES) was used to determine the metals concentration. The results showed that Acidithiobacillus ferrooxidans-LR leached 63% copper from printed circuit boards using supplemented medium with Fe+2.IntroductionThe waste of electric and electronic equipment is generated by discarding of equipment such as obsolete computers and cell phones which is stimulated by the technology innovations and it has been growing each year. Because of the amount that has been accumulated it has become a prominent environmental problem but also can be a source of valuable materials, such precious and base metals [1,2] The printed circuit boards are found in almost all electric and electronic equipment being composed of polymers, ceramics and metals and can be an alternative source to recover base and precious metals. The precious metals are used in the printed circuit boards to protect against oxidation and base metals because of its conducting properties [3]. The heterogeneous composition of printed circuit board is a limiting factor in the recycling processes and the metals concentrations also range."

Jan 1, 2011

By Wellington Pereira Inácio, Frederico Muylaert Margem, Artur Camposo Pereira, Sergio Neves

"Natural fibers are currently gaining attention as reinforcement of polymer composites for uses in engineering parts for automobile and building construction. In spite of environmental, economical and societal advantages, the natural lignocellulosic fibers are not as uniform in their dimension and properties as compared to synthetic. In recent works it was found that the variation in strength could be correlate to the equivalent diameters for several lignocellulosic fibers including the sisal fibers. In the present work an investigation on a possible correlation of the equivalent diameter with changes in density and elastic modulus was carried out. Precise measurements of the equivalent diameter, conducted in a profile projector, were correlated with the density and the elastic modulus by means of the Weibull statistic analysis. The results showed that an inverse correlation with the diameter also applies for both the density and the elastic modulus with a high degree of precision. SEM observation of the sisal fiber in structure and fracture aspects strongly indicate that defects and microfibril participation could be responsible for the inverse correlation.IntroductionAccording to Kalia [1], cellulose-based fibers are currently being pushed owing to their ""green"" image. Contrary to synthetic glass fiber, extensively used in our modem technology, these lignocellulosic fibers are renewable and can be incinerated at the end of the material's lifetime without adding pollution in the atmosphere moreover, the amount of CO2 released during incineration process is negligible as compared to the corresponding amount taken up by the plant throughout its lifetime. Even if an industrial processing equivalent of C02 release is added, the lignocellulosic fiber is considered neutral with respect to the emission of gases responsible for the global warming [2]."

Jan 1, 2012

By Alice Barreto Bevitori, Frederico Muylaert Margem, Noan Tonini SImonassi, Caroline Oliveyra, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"The mechanical behavior and the fracture characteristics of composites with DGEB/TETA epoxy matrix reinforced with up to 30% in volume of continuous and aligned ramie fibers were evaluated by tensile tests. Specimens with selected thin fibers aligned along the tensile axis were room temperature tested to rupture. The fracture surface was analyzed by scanning electron microscopy. The results showed significant increase in both the ultimate tensile strength and the elastic modulus. The fracture analysis indicated the possible mechanism for the fiber/matrix interaction, which could be responsible for the composite performance.IntroductionSince the middle of last century, polymer composites have substitute many conventional monolithic materials in applications ranging from aerospace to sport [l]. The main advantages of these composites are the low density and flexible properties specially using fiber as reinforcement to suit the mechanical performance requirements [2]. These are usually high strength and stiffuess requirements that could be reached with synthetic fibers such as gloss, carbon and aramid fibers. Its most commonly used example is ""fiberglass"", i.e., a thermoset polymer matrix composite reinforced with glass fiber. Indeed, ""fiberglass"" has a specific strength of the order of 500 MPa.cm3/g, which is the double of the strongest steels like the maraging. This motivated, at earlier times, ""fiberglass"" to replace many conventional materials including wood and natural fiber composites. Today, ""fiberglass"" has a wide range of uses from aerospace systems and appliances to sport and leisure components. However, its fabrication as well as those of any synthetic fiber such as carbon and aramid composites, requires a relatively large amount of energy. Presently, a growing concern exists regarding the consequences to the environmental by gases like C02 associated with both the energy consumption and the processing of synthetic fibers and their composites. These gases are well known responsible for global warming [3]."

Jan 1, 2013

By R. T. Jr. Faria, H. Vargas, R. Toledo, S. Cosin, V. P. Souza

"With the purpose of decrease environmental impact, caused by industrial residues (just discarded in the environment) and clay extraction in the ceramic industry, sanitary ware wastes were incorporated into clay. In contrast, it is important to evaluate not only the technological essays but also gases emissions in the ceramic firing process. The pollutant gases emitted in ceramic with residues can be in much larger concentrations than that in a pure clay ceramic firing or, on the other hand, can decrease the pollutant gas concentrations. With the aid of thermal analyses and photo acoustical techniques it was observed that sanitary ware waste can reduce the C02 emission. The gas emissions were shown as in function of firing temperature from 300 DC to 1100 DC. In order to analyze phase transformations during the firing process, clay samples and wastes were both analyzed by x-rays fluorescent chemical analysis and x-rays diffraction.IntroductionResearch works on the structural and physical changes that wastes, mainly industrially produced, cause to the final ceramic product has been rapidly expanding in these last two decades. See, for instance references in [1]. In spite of these examples of a continuous effort to incorporate wastes into clay ceramic motivated by technical and economical advantages, environmental issues are still a matter of concern. However, the gas emission due to the clay firing process and its related atmospheric pollution may be enhanced as a consequence of an incorporated waste [2]. It is known that the firing of clay ceramics in conventional furnaces using fuels such as wood, charcoal, heavy oil and natural gas generates appreciable amounts of gaseous components, mainly carbon dioxide (CO2), carbon monoxide (CO) and methane (CH4). Additionally to the atmospheric pollution, these gas sets could be harmful to the human health and can corrode equipments [3,4]."

Jan 1, 2012

By K. B. McTaggart, G. Owusu, P. J. Merrin

"This study was conducted at Hudson Bay Mining and Smelting's zinc electrowinning tankhouse to determine the effects of varying levels of antimony and continuous gelatin addition on current efficiency. The levels of antimony and gelatin were varied from 0.012 to 0.030 mg/l and 0 to 10 mg/ll2 • 31 respectively, based on neutral ZnS04 electrolyte. A non-linear mathematical model relating current efficiency with antimony and gelatin was produced. The optimum operating point for gelatin was 6.5 mg/l. On the other hand the current efficiency increased with decreasing antimony levels. An interaction term between gelatin and antimony is present but is not significant enough to improve the ability of the tankhouse to handle purification upsets in antimony. Individually, the current efficiency was linear (decreasing) with antimony, and parabolic with gelatin concentration. However, at low antimony concentrations stripping of the cathode sheet was difficult. IntroductionThe zinc electrowinning tankhouse at Hudson Bay Mining and Smelting was designed in the 1930's and consists of 120 rows with each row containing ten cells. This system cascades acid from cell to cell In a row, with neutral zinc sulphate solution added to each cell through manually controlled spigots. Animal glue additions are made manually three times per day by operations personnel. The problem with this type of cell design and operation is that feed solution flows and composition can vary from cell to cell and from row to row due to the large number of manual control points. A new system which reduces the number of manual control points was designed and tested to determine if improvement in control of cell conditions would affect current efficiency. This system mixes spent acid, neutral ZnS04 electrolyte and reagents (gelatin, antimony and strontium carbonate) in a separate mix tank, ensuring that all cells receive a uniform feed solution. Gelatin was used in the test system instead of animal glue (which is presently used) because of the poor solubility and supply of industrial animal glue. The study reported here is the first in a series of experiments designed to justify the need to modify the present cascading cell feed system (Figure 1) to the proposed feed system (figure 2)."

Jan 1, 1997

By Tian Tang, Sergio D. Felicelli

"The laser cladding is an important surface treatment for enhancing resistance against corrosion, abrasion, and wear. The focus of the present study is to develop a three dimensional finite element model to analyze the temperature history and thermal stress evolution during multi-pass laser cladding process on H13-H13 tool steel sample. A sequentially coupled thermal-stress analysis methodology was adopted in this study. The thermal model was firstly established to investigate the temperature history of the laser cladding process. Then the temperature history was used as input to mechanical model to calculate the thermal stress evolution during the process and the residual stress after the sample completely cooled down to room temperature. The influences of process parameters including the scanning speed and scanning strategies on temperature history, thermal stress evolution, and residual stress were investigated in details.IntroductionLaser cladding is an advanced material process technique, which is often used to improve mechanical properties or increase corrosion resistance, repair worn out parts, and fabricate metal matrix composites. In this process, the injected powder or wire feedstock material and a thin layer of substrate are melted and consolidated by use of a laser in order to coat part of a substrate or fabricate a near-net shape part.Numerous mathematical models have been established for analyzing the effects of process parameters, microstructure evolution, and thermo-mechanical behavior of laser cladding. Zhou et al. [1] established an analytical model to investigate the laser induction hybrid rapid cladding for Ni-based WC composite coatings. Huang et al. [2] also developed an analytical model to theoretically investigate the interaction between the laser beam and the powder stream of laser cladding process. A simple and realistic model of laser cladding was proposed by Picasso et al. [3]. The cladding layer is very sensitive to cracks due to the accumulation of residual stress, caused by non-uniform temperature changes, which have limited the wide application of laser cladding technique in industry. Recently, fmite element method has been increasingly used to simulate the laser cladding process [ 4-6]."

Jan 1, 2014

By David E. Hardt

"One of the critical variables to be controlled during arc welding is the size or geometry of the weld pool. The measurement of pool geometry has become an increasingly important problem with the advance of welding automation and control, and this paper addresses that problem. The basic concept of pool size estimation via measurement of pool dynamics is presented. The theory underlying this concept is discussed and is followed by a review of the current work in this area. It is concluded that pool dynamics can be characterized by natural frequencies of oscillation, for stationary welds, and that these can be measured by appropriate signal processing performed on the arc voltage. However, it appears that only full penetration welds show a strong correlation between weld size and natural frequency. Also, the extension of these results to the realistic case of moving welds has yet to be considered in detail. Nonetheless, this method of in-process measurement for real-time weld process control is still quite attractive where applicable since it can be accomplished simply by modifying the arc current schedule and by signal processing of the arc voltage.INTRODUCTUIONThe study of welding process control has been dominated by research into methods of in processing sensing of the weld pool geometry. While it has been shown feasible to measure the topside pool geometry using video methods [1,2], the penetration or backside bead width have remained elusive quantities. This is particularly true if a topside sensor location is required.The concept of using weld pool motion as a pool geometry sensing method was proposed by Hardt et al. [3] and later demonstrated by Hardt and Zacksenhouse [5] and Richardson and Renwick [6]. The concept is based on the fluid dynamics of a pool constrained by a solid container and by significant surface tension forces (i.e. a small shallow pool, not a ""pond"" or ""lake""). Such a pool, if subjected to external forces, will exhibit a surface motion is a function of that force, the properties of the fluid, the surface tension, and the shape of the container. Thus, if this motion can be excited and measured, and the relationship to the pool geometry determined, a means of sensing pool shape will exist."

Jan 1, 1986

By R. Boussaa, Y. Fautrelle, K. Zaidat, O. Budenkova, B. Saadi, X-D. Wang, L. Hachani, H. Ben Hadid

"Comparison of experimental data obtained in a benchmark experiment of solidification of a Sn-3%wt.Pb ingot and numerical results of two-dimensional and three-dimensional simulations of the process is presented. The benchmark experiment consisted in solidifying a rectangular ingot of Sn-3%wt.Pb alloy using two heat exchangers. Conditions of solidification were thoroughly controlled due to six thermocouples embedded into each heat exchanger. Due to another array of thermocouples the evolution of the temperature field at a lateral wall of the crucible was registered during the whole experiment. A treatment of the temperature data provided an estimation of the velocity field in the experiment. Post-mortem analyses of the sample provided the pattern of macrostructure of the sample and qualitative segregations pattern. 2D and 3D numerical solidification models are developed to give the distribution of the solute in a solidified sample.IntroductionConvection, either natural or forced, plays a very important role during the solidification. Its intensity and flow pattern affect heat and mass transfer and, consequently, macrostructure and segregation in a solidified ingot [1-4]. The effect of buoyancy convection during solidification has been studied in many laboratory-scale experiments [5-6]. Due to these experiments a general comprehension of formation of various defects in the ingot has been achieved. However, mentioned studies were not consistent since alloys, solidification conditions and configurations were every time chosen arbitrary. That is why the role of each parameter characterizing solidification process remains unclear. Moreover, the question of reproducibility of defects under the same solidification conditions still exists. In addition, most of the experiments suffer from the insufficient knowledge of control parameters that makes difficult their use for validation of models for solidification. These parameters serve as boundary conditions for numerical modeling and their incomplete description leads unavoidably to the errors in simulations. This situation motivated us to develop a setup for benchmark solidification experiments and to perform a set of the solidification experiments which we reported in [7]. Here we presented a comparison between results obtained in a benchmark experiment of solidification of Sn-3%wtPb ingot and its numerical modeling, which was performed in two-dimensional and three-dimensional configurations."

Jan 1, 2012

By B. Q. Li, S. P. Song

"Numerical models are developed to represent complex electromagnetic, free surface deformation and fluid flow phenomena in floating zone refining processes with radio frequency inductive heating. The computational methodology is based on the coupled finite/boundary element method for the electromagnetic field distribution and the Galerkin finite element method for magnetically driven fluid flow and free surface profiles of the molten zone. With the models, the complex transport and free surface phenomena in a floating zone system can be studied as a function of various operating conditions including applied current, frequency, inductor position and shape, surface tension, floating zone diameter and height. Results show that the equilibrium shape is sensitive to the height of the molten zone and that the free surface shapes can have a significant effect on the melt flow in the molten zone. Our extensive simulations also suggest that to ensure accurate results, the same mesh should be used, whenever possible, for both the electromagnetic forces and fluid flow calculations.1. IntroductionThe floating zone processes have been widely used in the materials industry to grow ultra-pure rare earth metal or semiconductor single crystals for sensor or electronic applications that have a tough demand on purity. Developed based on the principle of magnetic melting/levitation, the processes possess a main advantage that the molten zone is supported in air by the electromagnetic forces generated by the coil (see Figure 1), and therefore is free from contamination from a container. Consequently, the final products made from the floating zone processes have higher inherent purity than those by other techniques [1-4].Complex physical phenomena occur in the floating zone processing of materials. These include free surface deformation, magnetically-driven melt flow, which may be turbulent or mildly turbulent [5] depending on the applied conditions, and solidification. Thermal stresses also develop in the single crystals, which are affected by the flow and temperature field and which can have direct implications to qualities of single crystals [6]. An understanding of the fundamentals governing these physical phenomena can be of critical value in elucidating the physics that controls the properties of the metal or semiconductor crystals being produced, thereby providing a rational basis for process improvement and quality control."

Jan 1, 1997

By Ruixiang Wang, Jinhui Li, Youjun Xiao, Daoling Xiong, Hao Chen

"Leaching solution prepared from spent battery materials contains large quantities of valuable metals, such as Cu, Ni, Co, Mn and Fe. Therefore, recovery of valuable metals from acidic polymetallic aqueous solutions is of great importance for every plant. In this work, a method is introduced of recovery of Ni, Co and Mn from polymetallic solution prepared by leaching spent battery material. The basic concept includes copper was removed through replacement by iron powder followed by iron precipitation in goethite method. The experimental results show that Cu can be removed 99% at least through replacement by Fe powder, and the removal of Fe can achieve 99% by goethite method. At the same time, the loss of Ni, Co and Mn are about 2%, 3 % and 2%, respectively. The process of differential removal of metals can be selected as the treatment alternative that combines simplicity, efficiency and reliability with low capital and maintenance costs. The purified solution which only contains Ni, Co and Mn can be used to prepare NixCoyMnz ternary system precursor.1 IntroductionNickel and Cobalt are very important metals which are applied in many fields, such as energy material and support material for some new material field. The world demands for such metals is progressively increasing, while raw resources are being depleted and with the constraints raised by the Law and related legislation assigned to protect the environment from hazardous wastes in the world. Nowadays study on reutilization of waste materials has great significance for achieving secondary resources recycling and preventing environmental pollution. There are many hydrometallurgy methods applied for dealing with these wastes, while they usually contain large quantities of valuable metals, such as Cu, Co, Mn and Ni, as well as impurities, such as Fe, Zn, and etc. Therefore, proper treatment of these leaching solutions prior to their discharge is of great importance, so that the contained valuable metals can be recovered.Separation and extraction of metals from leaching solution can use some methods through solvent extraction[l,2], ion exchange[3,4], precipitation with sulfide[ 5] or alkali[ 6] and electrolytic recovery[?]. Among the appropriate treatment alternatives, replacement and differential precipitation is the most attractive treatment that combines simplicity, efficiency and reliability with low capital and maintenance costs."

Jan 1, 2011

By Lucas L. Costa, Luiz F. Lopes, Ludy C. Motta, Felipe P. D. Lopes, Sergio N. Monteiro, Lara S. Vasconcellos

"Environmentally correct materials like the lignocellulosic natural fibers, which are renewable and biodegradable, are being extensively investigated as possible substitutes for synthetic fiber in polymeric composites. Several natural fibers have never been thoroughly investigated as possible composite reinforcement. The fiber obtained from the leaves of the buriti (Mauritia flexuosa) palm tree is one example. Therefore, the objective of this work was to study the properties of buriti waste fibers, in amounts of up to 30%, reinforcing polyester composites.IntroductionIn the past century, the technological development gave priority to new synthetic materials with energy intensive methods of production. Today, there is a concern that conventional energy source such as petroleum, natural gas and coal are the main responsible for global warming. Therefore, the use of natural materials is gaining attention not only for the saving in process energy but also the renewable and biodegradable characteristics that make them environmentally correct. The lignocellulosic natural fibers extracted from cultivated vegetables like jute, sisal, hemp, coconut, flax, ramie and many others are typical examples. This type of fiber is being extensively investigated as a possible substitute for synthetic ones, especially the glass fiber, as composite reinforcement [1].A relevant example of lignocellulosic fiber substitution is nowadays occurring in vehicles. The automobile industry is applying composites reinforced with natural fibers to replace parts such as panels and seat cushions made of fiberglass or polymeric foams [4], as illustrated in Fig. 1. The practical reasons for this preference are that natural fiber composites present less damage to tools and molding equipments as well as relatively better finishing and less abrasive surface than corresponding parts made, for instance, of glass fibers. On top of these advantages, low cost is probably the main motivation for the industrial interest for natural fiber composites, especially in the case of residual fibers [5] or post-used fabrics such as jute sackcloth [6]. Natural fibers, however, are hydrophilic and will not form strong bonding with a hydrophobic polymer, normally used as composite matrix [1-3]. Another disadvantage is the heterogeneous characteristics of a natural fiber, which is typical of biomaterials. This results in a relatively great dispersion of dimensions and properties values such as the mechanical strength [1-3]."

Jan 1, 2008

By Michael Heximer, Dominic Verfielst, Timothy Moore

"Teck's Trail Operations recently installed new pressure filters in the cold stage purification step in the zinc leaching plant. Alloy 2205 duplex stainless steel was chosen as the material of construction as it was in use in the hot stage purification operation. Within a year of commissioning, an unacceptably high rate (greater than 1 mm/y) of corrosion was observed on the weld heat affected zone (HAZ). Laboratory and field tests were conducted to establish the conditions under which the corrosion was occurring. The tests isolated the aggressive conditions to a unique combination of materials present during the filter regeneration stage. Furthermore, the change of the duplex grain structure of the alloy during welding resulted in the HAZ being more susceptible to the corrosive environment. A new material of construction was recommended as a result of the investigation.IntroductionThe sulphide leaching plant uses four horizontal tank pressure leaf filters to remove solids precipitated in the cold stage electrolyte purification process. The current filters were installed in 2007, and replaced a bank of filter presses. The material of construction for the filters - alloy 2205 duplex stainless steel - was selected based on its successful use in similar service areas of the leaching plant. However, within the first year, unexpected and rapid corrosion of the filter tank material was observed. Although moderate general corrosion was noted throughout the filters, the attack was particularly aggressive in the areas where intense heat was applied during fabrication, observed at the HAZs caused by welding, and on the exposed edge grain of the duplex plates. On the inaugural annual inspection of the filters in the first year of operation, a corrosion penetration rate of 1.0 to 1.5 mm/y was observed at the HAZs. The parent plate of the pressure tank was a minimum of 6 mm, with a minimum allowable thickness of 3 mm under the ASME pressure tank design rules. Therefore, the projected useful life of the filters could then be roughly calculated to be two to three years. Urgent action was required to understand and correct this problem."

Jan 1, 2012

By Laurentiu Nastac

"An advanced casting simulation-based optimization approach was applied in this study to assist in the improvement of the mold design of aerospace components made of A3 56 alloy. By using this approach, mold filling and solidification related defects (including macro-shrinkage and shrinkage porosity) were significantly minimized and hence it helped in cost reduction, performance enhancement and quality assurance of complex A3 56 cast parts.An experimental validation and detailed calibration procedures of the models for prediction of macro-shrinkage and shrinkage porosities were performed using A3 5 6 plates cast in fiiran-silica sand molds using the Prometal's Rapid Casting Technology (RCT) - mold printing technology. Correlations between Niyama values and the pore percentage were also developed. Thus, the severity level of shrinkage porosity can be determined via the Niyama criterion. Predictions were then compared with the macro-shrinkage and porosity measurements in plates of various plate thicknesses and in other commercial A3 56 casting components.IntroductionThis paper describes the process modeling approach used in the development of the mold design technology used to produce assist in the improvement of the mold design of aerospace components made of A356 alloy. Nova Flow&Solid™ software [3] was applied in this study. This casting simulation software was previously validated for several alloys including Ti, steel and superalloys [1-4]. The objective of this paper is to calibrate and validate the simulation software for A356 alloy sand mold castings. For this purpose, an experimental validation and detailed calibration procedures of the models for prediction of macro-shrinkage and microshrinkage (e.g., shrinkage porosities) were performed using A356 plates cast in fiiran-silica sand molds using the Prometal Rapid Casting Technology (RCT) mold printing technology. The details of the RCT technology are shown in Fig. 1 [5]. Prometal's RCT technology is used for rapid production of sand molds and cores directly from CAD files. The RCT technology relies upon ink jet printer technology to selectively bind the grains of sand to create three-dimensional sand molds and cores. Mold filling and solidification modeling as well as stress analysis are typically performed to properly design the casting and the rig system of each prototype component."

Jan 1, 2012

By Z. Smieszek, Z. Szota, P. Gajowski

"A new method for measuring the total quantity of suspensions contained in the electrolyte during copper electrorefining has been developed by the Institute of Non-Ferrous Metals, Gliwice. Electrolyte purity, and the suspensions content in particular, is of essential importance for the quality of electrolytic copper produced during the process. Suspensions contribute to the increase of slime impurities in electrolytic copper and increase losses in noble metals. Up to now, the laboratory method has been used for the· process control which provides analytical results with considerable time delay. Therefore, it is useless for the process control.The measuring method developed enables continuous measurements of a suspensions content directly within the stream of the flowing electrolyte. The principle of measurement is based on changes in optic properties of the electrolyte with varying suspensions content.1. IntroductionIn copper electrorefining, it is essential that the final product quality be maintained. If suspensions are present in electrolyte, the content of slime impurities in electrolytic copper, (such as Pb, Ag, Bi, Sn, Sb, and As), increases which can result in the occurrence of the so-called slime dendrites on cathodes, thus debasing the quality of the product. As a normal suspension content in electrolyte, the contents in the order of several mg/l are considered, usually not more than 5-6 mg/l, while contents exceeding 20 mg/l are referred to as an alarm state. Suspensions present in an electrolyte are usually a light fraction of anodic slime whose main components are metallic silver, lead sulphate, complexes of antimony and arsenic, and sometimes even calcium sulphate; they are mainly composed of very small particles of lead sulphate and antimony complexes. Sometimes - - in case of alarm states - - the so-called ""wandering slims"" can be observed, which are composed mainly of arsenic and antimony complexes. These ""wandering slims"" make a serious technological disturbance. In normal operating conditions of the electrorefining plant, an increase of suspension content can result from such reasons as crack of filter cloth in a slime filter, turbulent flow of the electrolyte, anodic passivation, aeration of the electrolyte, and improper servicing of an electrolytic tank. It is necessary to continuously control the suspensions content in electrolyte for proper electrorefining."

Jan 1, 1989

By J. P. Downey, L. G. Twidwell

"The high density sludge process (HDS) is a commercially proven acid rock drainage wastewater treatment process that is based on acid neutralization and metal precipitation. Previous studies have established that metal removal efficiencies in precipitation-based wastewater treatment applications can be improved through metal ion adsorption on ferrihydrite and/or aluminummodified ferrihydrite. This study was conducted specifically to determine whether the metals removal efficiencies at an existing industrial facility could be improved by promoting ferrihydrite and/or aluminum-modified ferrihydrite precipitation during the pH adjustment stages of the HDS process. The metal tenors of the treated wastewater samples are compared with those obtained through baseline experiments, which were designed to simulate the conventional HDS operation. The subject metals were: aluminum, arsenic, cadmium, copper, iron, manganese, nickel, and zinc.IntroductionThe HDS process is commercially proven ARD wastewater treatment technology that involves raising the wastewater pH by adding hydrated lime, caustic soda, or another alkaline substance. In addition to neutralizing the acidity, many dissolved metals precipitate as pH is elevated. Waste volume is minimized by capturing and immobilizing the precipitated solids.However, ARD streams characteristically contain multiple dissolved metal species. The response of various metals to pH adjustment in the HDS process is neither uniform nor quantitative, so minor to trace concentrations typically remain in the treated wastewater following solid-liquid separation. The effectiveness and applicability of the process would be improved if a means were found to further reduce the metal concentrations.Previous research and industrial applications have proven that metal ion adsorption on ferrihydrite (FH) and/or aluminum-modified ferrihydrite (AMF) increase metal removal efficiencies. Ferrihydrite and AMF are considered ideal for cation and anion adsorption from an aqueous solution at the appropriate pH [1]. Ferrihydrate adsorption of dissolved heavy metals is widely practiced throughout the world [2, 3]. It is established that FH and AMF effectively adsorb As contained in aqueous solutions [4]. Arsenic removal by adsorption on FH is the U.S. Environmental Protection Agency’s (EPA) Best Demonstrated Available Technology [5]. Twidwell and Leonhard also demonstrated that heavy metals (Cd, Cu, Ni, and Zn) are effectively removed from solution by coprecipitation/adsorption using AMF and FH [6]."

Jan 1, 2008

By Xiangjun Zuo, Lifeng Zhang

"Printed Wiring Board (PWB) is a platform upon which microelectronic components such as semiconductor chips and capacitors are mounted. It is also called printed circuit board (PCB). In the PWBs, the organic substances are approximately 72%. The main composition of organic substances in PWBs is ethoxyline resin bromide or ethoxyline resin chlorinate. Depending on the different application and design of the PWB, various metals may be used in the manufacturing process, including precious metals such as copper, lead, silver, gold, platinum, and toxic metals such as mercury, cadmium, barium, gallium, cadmium, lead, bismuth. The current paper reviewed the recycling process for waste PWB materials, including mechanical recycling, combustion for energy recovery and different pyrolysis processes, such as vacuum pyrolysis, atmospheric inert pyrolysi and flux pyrolysis process, and hydrometallurgical recycling process.Backgrounds of Electronic ScrapsProduction and use of electrical and electronic equipment (EEE), such as TV sets, computers, mobile phones and many other daily-life items, have dramatically increased over past decades, while the lifespan of many products becomes shorter"". The rapid innovation in technology in past decades has resulted in availability of cheaper and better electronic products in the market. Thus the production of waste electrical and electronic equipment (WEEE) is also increasing, with estimates of 20-50 million tons per year being generated worldwide2), and it is a problem that governments and policy makers have to handle W). WEEE is also called ""E-wastes"" or ""E-scraps"". From the points of view of recycling and the valuable materials in the used EEE, ""E-scrap"" is more appropriate than ""E-waste"" since the used EEE are not real wastes to be dumped but had much benefit to recycle. In the US, it was estimated that over 315 million computers between 1997 and 2004 and 185 million computers between 2004 and 2007 would become obsolete 5). E-scrap is the fastest-growing part of the U.S. garbage stream 6). It is estimated that only 20% of the E-scrap generated within the US is currently collected and treated, with as much as 80% being unaccounted for7)."

Jan 1, 2011

By Antonio de Lucas, Juan Francisco Rodríguez, Ignacio Gracia, Mª Teresa García

"The amount of waste of Polystyrene (PS) foams is increasing in last years due to their use in insulation, protecting and, storing many different food products. Conventional methods of recycling such as crushing and shrinking by heated air or frictional heat have the disadvantages of molecular degradation, resulting in a reduction of the quality of the recycled polymer. Dissolution and shrinking with suitable solvents is one of the cheapest and more efficient ways of polystyrene recycling but in the process of the solvent recovery by distillation a certain degree of molecular degradation is produced. In this way, CO2 supercritical technology appears as an interesting alternative for the elimination of solvent. This work proposes a global process to polystyrene recycling in two steps: a polystyrene dissolution with a suitable “green” solvent followed by its elimination by supercritical tecnologhy. In order to develop a “green process” the constituents of essential oils, limonene, terpinene, cymene, and phellandrene, are selected as the most appropriated solvents. Introduction In the last years, disposal of the non-biodegradable plastic wastes has been recognized as a serious environmental problem. Recycling these wastes has great interest in order to prevent the environmental pollution and to preserve natural sources (1, 2, 3). Since the Polystyrene foams (PS) is one of the most used foam in isolation, protecting and food storage most of recycling work is concerned with this polyolefin (4). The two main alternatives for treating polymer wastes are energy recycling, where wastes are incinerated, and mechanical recycling (5). Environmental argumentations such as toxic emissions are building up a public resistance against incineration process (6). Mechanical recycling is a popular recovery path for manufacturers and is carried out on single-polymer waste streams. Any way, the market for recycled products can only be found if the quality is close to that of the original. Unfortunately the process of classification and further recovery of these wastes makes them often more expensive than virgin plastic (7, 8). Solvent extraction is one of the cheapest and more efficient ways for PS recycling. If it is done in house of waste producers the separation between plastics could be easy and effective and the transport costs would be eliminated."

Jan 1, 2008

By Mingming Zhang

"Three samples received from the EAF shop have been characterized by chemical, X-ray diffraction (XRD), optical microscopy (OM) and scanning electron microscopy (SEM) methods. The objective of this characterization work is to investigate the occurrence of nickel, copper, zinc, sulfur and phosphorus in these samples and identity their origin and associations with iron minerals in the concentrate samples that are from mines.The samples were identified as Mineral, Pellet, and HRD. The latter is the DR! product. All three samples were received as fine powders. The results indicate that, in the mineral sample, magnetite is the major iron oxide mineral with hematite as a second phase based on the OM and XRD studies. Pyrite [FeS2], chalcopyrite [CuFeS2] and bravoite [(Fe,Ni)S2] are major sulfide minerals. Trace amounts of apatite [Ca5(P04)3(F,Cl,OH)], wardite [Na4CaA112(P04)8(OH)8 6H20], giniite [Fe5(P04)4(OH)3 2H20] and vivianite [Fe3(p04)2 8H20] were identified by SEM and XRD. Microscopic studies also indicated that most of the sulfide grains in the mineral sample are present either as liberated fine particles (about 10 microns) or as inclusions within the magnetite and hematite grains. XRD studies revealed magnetite as the major mineral with subordinate amounts of hematite and pyrite confirming the microscopic findings. Copper, nickel, and zinc are mainly present as chalcopyrite, bravoite, and franklinite [(Zn,Mn,Fe)(Fe,Mn)204] in trace amount in the mineral samples, respectively. Impurities carry over to the Pellet and HRD samples.Chemical analyses of the three iron-bearing samples indicate that sulfur and phosphorus in the Pellet sample exceeded the specification. Since liberated pyrite and chalcopyrite particles were observed both in mineral and pellet samples, magnetic and flotation processing routes for this ore should be effective for sulfide removal but at the cost of iron losses. The high phosphorus content of all three samples indicates that there are phosphates which are difficult to remove by the current concentrating process (magnetic separation and flotation)"

Jan 1, 2012