Search Documents

By Shaohua Ju, Huang Chang-yuan, Lu Shuaidan, Peng Jin-hui, Wu Guoqin, Yaqian Wei, Zhang Li-bo

"The contrastive studies of microwave and conventional roasting copper residue from zinc hydrometallurgical was carried. The experimental results showed that the microwave roasting has the higher dechlorination rate in the same condition such as temperature, heat preservation time and atmosphere. When the samples with 100 mesh grain size, the Cl content turned from 14.27% to 1.33% and the dechlorination rate achieved over 90% at 400°C with 2h microwave roasting. And in the same conditions, the materials' dechlorination rate after conventional roasting just reached around 78%. The phase changes of the roasting process was investigated with X-ray diffraction analysis.IntroductionCl element can be accumulated gradually in the solution of Zinc hydrometallurgical system. When Cl content in electrolysis solution comes up to 100 mg/L, the stability of electrodeposits process would be severely affected [ 1]. It would not only accelerate the consumption of cathode and anode plate, elevate the power consumption, but also cause serious corrosion of device, increase production costs and lower the quality of electrolytic zinc [2]. Thus, C1- contained in the solution should be removed before electrodeposits."

Jan 1, 2013

By Sergio N. Monteiro

The interface between the matrix and the reinforcing fiber plays an important role in the efficiency by which an applied load is transmitted through the composite structure. The shear stress at the fiber/matrix interface can be associated with this load transference and,consequently,affects the composite strength. In the present work, pullout tests were used to evaluate the interfacial shear stress of curaua fiber in epoxy matrix composites. A small critical length was found for the curaua fiber embedded in epoxy, which corresponds to a relatively weak fiber/matrix bond and lower interfacial strength.

Jan 1, 2009

By Klas G. Hultbom

Mercury is present as trace contaminant in many raw materials for metallurgical plants. When such materials are treated with pyrometallurgical processes the mercury is volatilised. Mercury has a high vapour pressure, even at low temperatures, and therefore it is removed only partly by normal gas cleaning processes. The Boliden Norzink scrubbing process removes elemental mercury by converting it to calomel. It is widely used in the base metals industry. This paper gives examples of the application, and also outlines the background for the development of the process. Another technology developed by Boliden for mercury removal is the Selenium filter. This is a fixed bed filter based on the reaction between elemental gaseous mercury and selenium, by which mercury selenide, HgSe, is formed. The mercury selenide is a highly stable compound with extremely low solubility in water and very low vapour pressure. Mercury is removed selectively without any side reactions. Special applications for the selenium filter technology include mercury removal from gases containing sulphur dioxide and geothermal off-gases.

Jan 1, 2003

By Sergio N. Monteiro

Fibers extracted from the ramie plant have been traditionally used in textile and are now being considered as polymeric composite reinforcement owing to their superior strength. Recently the mechanical behavior of ramie fiber reinforced polyester composites was investigated but no significant improvement was found. Therefore, the objective of this work was to carry out a similar investigation by changing the type of polymeric matrix. Specimens with up to 30% in volume of ramie fibers incorporated into epoxy were bend-tested until fracture. The results showed a moderate improvement with a tendency of decreasing stress for higher amounts of ramie fibers due to the weak interface developed with the epoxy matrix.

Jan 1, 2009

By Wei-ling Wang, Ryosuke O. Suzuki, Xiang-ning Meng, Miao-yong Zhu

"A finite-element thermal-stress model of continuous casting mold is conducted to predict deformation of copper plates and its change with different cooling structure. The results show that deformation behavior of copper plates is mainly governed by cooling structure and thermal- mechanical conditions, deformation amount is related to structure geometry, and a small deformation mutation occurs in cooper-nickel boundary due to different properties. The maximum deformation of hot surface centricities of wide face locate at 100 mm below meniscus and that of narrow face locate at meniscus and terminal of water slots and significant curvature fluctuations on both sides of copper-nickel boundary. The maximum deformation of centricities is increased up to 0.05 mm with thickness increment 5 mm of copper plates, and maximum deformations are only depressed 0.01 mm and 0.02 mm with increments of 1 mm nickel layer thickness and 2 mm water slot depth respectively.IntroductionIn conventional continuous casting of steel, a large amount of sensible and latent heat of molten steel dissipate in primary cooling zone and make continuous casting mold under enormous heating load giving rise to thermal stress, deformation, high-temperature fatigue and creep not only depress mold life-span, but reduce casting stability [1] Many studies focused more on heat transfer, solidification and shrinkage of solidifying shell to provide inverse proposals for optimizing cooling system and even designing new taper of mold [2,3], but it is generally useless to those of having been manufactured or being put into production. Therefore, mold-related forward problems show necessity to be discussed deeply, and stress and deformation distributions based on special thermal conditions in mold should be analyzed in order to explore suitable cooling structure of mold directly. Samarasekera et al. [4] examined heat flow and distortion of two-dimensional longitudinal sections and investigated effect of cooling water velocity, copper plates thickness and carbon content on formation of rhomboidity and longitudinal comer cracks. O'Connor et al. [5] developed a three-dimensional mathematical model to compute thermo-mechanical state in thin-slab mold and calculated temperature and deformation of mold wall to assess roles of various process parameters on impacting mold life. Thomas et al. [6] predicted temperature, distortion and residual stress in mold and indicated increased distortion requires increased remachining, which reduces mold life and increased residual stress increases the probability of a catastrophic crack failure. Park et al. [7l determined heat-flux profiles in funnel-shaped and parallel thin-slab molds based on an inverse heat conduction model and thermocouple temperature measured in-plant and put them into three- dimensional finite-element thermal-stress model to predict temperature, distortion and residual stress of mold wall. Korie et al. [SJ focused on prediction of temperature, distortion and residual stress in mold and in particular to clarify that mold life is significantly affected by temperature and its rigidity, but little effect by mechanical including clamping force, bolt prestress, friction and ferrostatic pressure. Meng et al. [9l predicted temperature and thermal stress in a slab mold and analyzed effect by cooling system geometry and casting speed quantitatively. In present study, a three-dimensional finite-element thermo-mechanical model with type-switched element is transformed from previous heat-transfer finite-element model [9l, and mold deformation is simulated in order to shed light on thermo-mechanical behavior with special thermal conditions and different mold geometry at high casting speed."

Jan 1, 2013

By A. V. Tarasov, S. D. Klushin

493 The most common method for minimizing the copper content of residual slag in the process of autogenous smelting of sulfide raw materials is treatment of molten slag in an electric furnace, with optional addition of solid reducing agents, such as coke, and/or sulfiding agents such as pyrite. A drawback of this technique is the fact that the final slag produced still contains 0.5% or more Cu. We have tested a method for treating molten slag obtained as a result of autogenous smelting by a gaseous mixture of sulfur dioxide and methane at a ratio of. SC:SO2 = 0.75 :1.0 in the presence of oxygen. Interaction reaction within the SO2-O2-CRi system proceeded at a high rate at 1373 to 1573 K to form reducing and sulfiding agents: H2S, S, COS, CO, CO2, H2, H2O. The gas mixture requirement was about 100 to 150 Nm3 per 1 tonne of slag. A decrease in the ferric iron concentration (Fe3+) from 10-15% down to 2-3% resulted in lower solubility of copper in slag, and agitation of the melt with gas stream accelerated. the separation of the sulfide phase and slag. Removal of copper from slag was performed in a pilot unit within the second V anyukov furnace zone where slag arrived with a copper content of 0.8-1.3%. The temperature of molten slag was maintained within 1523 to 1573 K. The copper content of the final slag was at a level of0.12 to 0.14%. The matte sent to converting was a mixture of bottom matte from the smelting zone and the slag treatment zone. It had a copper content of about 50 to 55%. Process gases from both furnace zones were combined and sent to the acid plant for sulfur recovery. This process was offered for commercial use at two copper smelters in Russia and CIS.

Jan 1, 2000

By Sergio N. Monteiro

Jute fabric obtained from discarded sackcloth is a promising low cost and post-used material being considered as reinforcement of polymeric matrix composites. In particular, the combination of this fabric with a recycled plastic constitutes an environmentally correct composite with both economical and environmental advantages. The present work investigates the toughness of recycled polyethylene composites reinforced with up to 40 wt% of post-used jute fabric extracted from discarded sackcloth. Standard Izod notched specimens were impact tested and the results showed an increase in toughness with the amount of jute fabric. Observation of the composite fracture by SEM revealed that the fabric weave, in spite of damages caused by the previous use of the sackcloth, act as an effective obstacle to crack propagation.

Jan 1, 2009

By J. P. Downey, T. Salisbury, M. Berlin, E. Rosenberg, G. Pinson, R. Christianson, K. Gleason, W. Gleason, S. Davis

"Direct digital manufacturing offers promise as a technique for fabricating complex hydrogen purification membrane support structures. Free form fabrication methods can produce parts with complex structures, and sintering parameters can be controlled to adjust the density, pore structure, pore pathways and strength in catalytic substrate constructs. Efforts are underway to define the influence of selected process variables on the chemical and mechanical properties.IntroductionThe Center for Advanced Mineral and Metallurgical Processes (CAMP), in collaboration with the Metallurgical and Materials Engineering Department at Montana Tech and the Chemistry Department at the University of Montana, is engaged in the development of new methods and materials for hydrogen purification membrane production. Because hydrogen readily passes through palladium, a structurally sound palladium-based membrane is capable of separating relatively pure hydrogen from other gases. In order for this technology to succeed, a suitable substrate material must be identified.High purity hydrogen is produced by various means. A common method involves a two-stage process for separating hydrogen from a hydrocarbon gas stream: 1) hydrogen-rich syngas is produced by the catalytic reaction of natural gas or another light hydrocarbon gas with steam, and 2) hydrogen is separated from the other syngas components by pressure swing adsorption (PSA) (US. Energy Information Agency, 2011). In PSA, gases enter a column that is packed with a material that absorbs gases as the chamber is filled and pressurized. As the pressure is slowly relieved, the absorbent material releases hydrogen at a higher pressure than the impurity gases. PSA processes produce 99.99% pure hydrogen at a high recovery rate. These systems typically demand a high capital investment due to the high pressure and multiple stages (columns) needed to attain high hydrogen production rates.Research geared toward reducing hydrogen production cost is focused on the development of improved catalysts and adsorbent materials as well as more effective single-stage separation processes. An interesting method combines hydrogen reduction catalysis and filtration. Nascent hydrogen is separated from other gases as it selectively permeates the filter. Catalyst filters may be made of gold, silver, platinum, palladium or precious metal alloys (Davis, 2009)."

Jan 1, 2012

By T. A. Edison

A distinct hydrocarbon maturation anomaly coincides with the Gold Acres open pit, Nevada (Figure 1). Both atomic hydrogen to carbon (H-C) ratios and reflectance measurements of contained organic matter indicate significantly higher maturity in samples collected within the confines of the open pit than in samples from the surrounding region (not shown in Figure 1).

Jan 1, 1987

By Alexandra Anderson

A computational fluid dynamic (CFD) model has been developed using ANSYS Fluent 17.0 to help identify areas of high wear within the refractory lining of a secondary lead reverberatory furnace. Once a base case simulation was validated using data from an operational furnace, areas of potentially high refractory wear were determined through the calculation of the temperature and velocity distributions within the furnace and on the hot face of the refractory lining. The CFD model was used to assess whether the predicted areas of high refractory wear could be minimized through changes burden geometry. The results showed that shape of the burden geometry greatly affected the overall flow patterns and heat transfer within the furnace.

By K. B. Shedd

Questions regarding possible adverse health effects from exposure to zeolites arose when the inhabitants of two villages in Turkey were found to have high incidences of mesothelioma, a disease generally identified with exposure to asbestos. No asbestos deposits are known in the area, but some fibrous zeolites have been found. Further investigations have resulted in conflicting opinions as to whether fibrous zeolites are related to the high incidence of mesothelioma in Turkey. The U.S. Department of the Interior, Bureau of Mines examined the habits of domestic zeolites by scanning and transmission electron microscopy. Only erionite and mordenite particles possessed acicular to fibrous habits. With the exception of a rarely occurring woolly erionite sample, the fibrous zeolites were not dimensionally equivalent to asbestos.

Jan 1, 1982

By Wang Shuchan, Zhang Zimu, Zhang Dianhua, Liu Yan, Zhang Ting-an, Zhao Qiuyue, Lv Chao

Rare earth extraction tank has many adverse effects like big floor space and high production accumulation during industrial production. Current researches usually focus on changing the device structure without making a breakthrough towards gravity clarification. This paper attempts to achieve this goal by using both the action of clarification by gravity and clarification by stirring. Because many physical parameters affect the clarification and separation rates, the density, viscosity and surface tension of the two phases were determined at different temperatures and different concentration of aqueous solution. The innovation of this research involves adopting the Karl-Fischer method to investigate water content in oil phase during the stirred separation process. In this paper, the separation effect of different physical parameters was studied and the dimensional equation between water content and the physical parameters was established by combining with the experimental data.

Jan 1, 2014

By M. F. El-Demerdash

The activity distribution diagrams for different species in aqueous systems are developed. Computational method may be considered as an extension of the Activity-Term method introduced by the authors to construct EH-pH diagrams. In the Activity-Term method, all activities of different species are evaluated before deciding the most stable one. In the present study, a factor is assumed to allow for the conservation of the element. At any point, the total concentration of all species should contain only the input m moles of the element (elements) considered. This approach is applied to Zn-, 5-, and Zn-S-H2O and activity distribution diagrams are plotted as a function of pH, at different potential levels and at different temperatures.

Jan 1, 1990

By Bingyi Bai, Wangjun Peng, Yanling Guo, Jieyu Zhang, Guoding Gao

The phase transformation of bayan obo ore with high concentration of iron and calcium was reduced at temperatures no more than 1000℃ were investigated in this study. The samples with insufficient carbon were treated at the temperature using a vertical furnace with a thermogravimetry (TG). The mineral phases and content were examined using Xray diffraction (XRD) and X-ray fluorescence spectroscopy (XRF) respectively. The complex phases of bayan obo ore transformed to some simple phases after treated with different content of carbon at the same temperature for 10 hours. The result of XRD、 XRF and TG showed that the reduction degree of Fe3O4 phase formation varied with the temperature and the carbon content of bayan obo ore.

Jan 1, 2015

By Jinrong Zhang

Fresh cyanide solution was treated by near UV light with the assistance of photocatalysts. Cyanide was oxidized mainly to cyanate. Photochemical behavior of the anatase and rutile forms of TiO2 was compared. It is found that anatase has a much higher activity than that of rutile. Bubbling of oxygen in the reactor showed no appreciable increase in cyanide oxidation, implying that the reaction is surface controlling. A very interesting finding in this study is that a natural mineral, ilmenite, can replace chemical titanium dioxide as the photocatalyst. Ilmenite without any treatment did not catalyze the oxidation of cyanide. But, after being roasted at high temperature with oxygen, the oxidation was enhanced dramatically. The mechanisms of photooxidation of cyanide and the roasting of ilmenite are proposed.

Jan 1, 1991

By Zhi-xiang Cui

Dongying Fangyuan Nonferrous Metals Co., Ltd. has developed a new technology to produce anode copper from concentrates through only two furnaces. This new technology is called the Two-Step Copper Smelting Process. This paper presents the commercial application of the Two-Step Copper Smelting Process and its operating conditions. The key features of the Fangyuan Two-Step Process are as follows: (1) feed materials, including concentrates and flux, are mixed without pretreatment and fed into the Submerged Lance Smelting (SLS) furnace; (2) high grade white metal (WM) produced by the SLS furnace is transferred via WM conduit into one of the two Submerged Lance Converting and Refining (SLCR) furnaces; and (3) the two SLCR furnaces blow alternatively to maintain continuous operation of the whole production chain. The new smelter started operation in October 2015 with a processing design capacity of 1.75 Mt/year of mixed feed and has been operating for over 30 months.

By C. J. Parradies

During injection into a die, semi-solid metal alloys exhibit a shear-rate, history-dependent flow response. Simulating the injection of a thixotropic material requires that empirically determined boundary conditions and viscosity are specified as a function of both temperature and shear rate history. Experiments were performed using an industrial die casting machine that was instrumented with sensors to measure the pressure and temperature during the injection of a semi-solid aluminum alloy through a tube. This benchmark experiment was used to develop a simulation of the die casting process that could then be applied to more complex die geometries. The results of the experiments were analyzed using the exact, steady state solution for a power law fluid and simulations accounting for slipping at the boundary between the semi-solid metal and the die. Results indicated that the no-slip condition cannot be used to simulate the velocity boundary condition, because the measured pressure is much lower than that predicted by the models. An estimated apparent slip coefficient was introduced to account for the reduced pressure. During some of the experiments, a sudden drop in the measured pressured, prior to decreasing the ram velocity, coincided with observations of segregation in the form of concentric rings visible on the polished surface of cross-sections cut from material remaining in the tube.

Jan 1, 1997

By Roderick Guthrie

Gas injection into liquid steel baths is widely practiced, ever since the early days of Bessemer’s pneumatic steelmaking process. What has not been fully appreciated is the critical role of bubble sizes for delivering higher quality commercial steels than is presently possible. This was first proposed by Prof P. Hayes and his research group. Using a full-scale water model of a typical 4-strand Ladle-Tundish-Mold system, we demonstrate the potential advantages of modifying a typical ladle shroud, to generate microbubbles within the water flowing into the tundish. This is possible by taking advantage of high shear rates and turbulence kinetic energy available in that region. These microbubbles enhanced the removal of “micro-inclusions” (hollow glass microspheres) in the 5–50 micron size range, to the upper surface of the tundish. There, they were absorbed into an overlaying “slag” phase. Accompanying CFD studies confirmed that no microbubbles in the size range generated (500–900 μm), pass through the submerged entry nozzles into the moulds.

By Zenjiro Asaki

The copper concentrate particles dissolve quickly into the molten matte in the smelting furnace of Mitsubishi Process, which indicates that the sulfide smelting is essentially a gas/liquid reaction. In this paper, theoretical calculation has been made on the rate of oxidation of FeS component in the matte to form FeO by rising gas bubbles using the penetration theory. The results showed that all the oxygen in the bubble of 1.2 cm in diameter, which is the maximum stable diameter, is consumed in 3 ms. This time required is sufficiently short, and it results in the actual operation of smelting furnace of 1100% oxygen-efficiency. These calculations indicate that most smelting reactions are completed just under the lance, except slag formation.

Jan 1, 2002

By Edward Peters

Scandium (Sc) has unique properties and is one of the more valuable elements in the periodic table. Scandium can be used in solid oxide fuel cells and to produce high strength aluminium alloys of value, for example, in the aerospace industry. Scandium is often grouped together with the rare earth elements (REE). Amongst others, scandium can be found in bauxite residues, so called red mud. It is possible to extract and enrich scandium from red mud by leaching and solvent extraction. Scandium can then be recovered from the pregnant strip liquor by crystallization. The strip liquor will however still contain certain impurity elements. In the present work, a method for obtaining a pure scandium solid phase by direct crystallization from the strip liquor is evaluated. It was found that Fe and Ti co-precipitate with Sc under the conditions employed.