Search Documents

By Jorge A. S. Tenorio, Chuanwei Zhuo, Joner O. Alves, Yiannis A. Levendis

"The ever increasing number of automobiles and the consequential increase in consumption of tires have generated a pressing environmental issue, concerning the disposal of unserviceable tires. The worldwide disposed of waste tires is approximately 1 billion units per year and this amount is expected to increase by 2% each year. This work presents a microstructural characterization of nanomaterials synthesized in a catalyst system from the effluent of burning waste tire chips in a horizontal two-stage laminar-flow furnace. Controlled combustion of waste tire chips took place at temperatures of 900 or 1000 °C, and stainless steel meshes were used to synthesize the nanomaterials at 1000°C. Produced materials were analyzed by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). The catalyst meshes were covered by materials with diameters of 20 to 200 nm and lengths of about 40 µm. They possessed structures similar to those of carbon nanotubes.IntroductionThe motor vehicles on the road have been increasing annually. World motor vehicle production in 2009 approached 62 million units. Consequently, the consumption of tires has also been on the rise; about 1.4 billion units were produced around the world in 2007 [l]. The disposal of scrap tires is a serious environmental problem. The worldwide disposed of waste tires is almost 1 billion units per year with an expected increase of around 2% each year. However, less than 7% of produced waste tires are recycled (excluding reuse, retreading or incineration). The waste rubber tires are a thermoset polymer, which cannot be reprocessed like thermoplastics polymers, therefore the recycling of this material requires special techniques that demand big investments [2, 3].A solution to the disposal of waste tires is the sequential pyrolysis/combustion process. Past research showed that waste tires are an attractive potential fuel due the high heating value (29-3 7 MJ/kg), which is comparable, or even higher to those of typical bituminous coals [ 4, 5]. Pyrolysis is a process wherein the material is thermally decomposed at elevated temperatures at the absence of an oxidizing gas. Combustion is characterized by the addition of the oxidizing gases during the process. Several studies indicate that the pyrolysis and combustion processes for the tires treatment have a great energy conversion potential [4, 5, 6]."

Jan 1, 2011

By Ronald L. Pariani

To date, significant advances have been made regarding the development and commercial implementation of full deposit stripping in the copper industry such as practiced at Copper Refineries, LTD in Townsville, Australia. The paper describes the history and current practice of Electrowinning (EW) plants which may be coupled with solvent extraction. The modular nature and degree of automation are described in relation to the various sizes of operations. Reference is made to the expansion capability of commercial equipment plus associated economics of the mechanical processes for producing full cathode deposits. It is recognized that the technology described may be adaptable to other nonferrous refining areas where feasible. The paper highlights the state of the art in mechanized stripping equipment as applied to current and planned SX-EW plants.

Jan 1, 1987

By Dieter Wanner

Off-gas cleaning from metallurgical? plants, requires in many cases very low dust contents which are, difficult to achieve with conventional scrubbers, even with high energy input. Lurgi has developed a scrubber which improves the separation of the fine dust by electrical charge prior to the scrubbing zone,, An Electrostatic Scrubber has been successfully installed for the off-gas cleaning from slag granulation after a waelz kiln achieving less than l mg/m3 in the clean gas.

Jan 1, 1992

By K. Sarveswara Rao

The present paper firstly describes some recent trends from literature on energy management via process intensification to arrive at sustainable technologies for aqueous processing of minerals, metals and materials. Secondly, the energy saving measures practiced in leaching, solid-solution separation, solution purification, metal and material winning and environmental aspects have been discussed. The emerging importance of interdisciplinary nature of hydrometallurgy for practical applications is also highlighted. With the above background, the present paper describes an overview of energy conservation and autoclave processes with a special reference to hydrometallurgical research activities of our Laboratory.

Jan 1, 2008

By Li Zhang

A novel green technology to recovery Titanium compounds from Ti-bearing blast furnace slag under the dynamic oxidation condition was developed and tested. Air was blown into the molten slag as oxygen resource through a lance during the dynamic oxidation process, in which six important results were found: (1) The TiC, (Ti2O3), Fe and (FeO) in the slag were oxidized; (2) The temperature of slag temperature rapidly increased; (3) The viscosity of slag decreased; (4) The coalescence, growth and drop of the metallic Fe droplets in the molten slag were carried out under an air agitation condition; (5) The dispersed Ti components were selectively enriched into the perovslite phase, and the perovskite phase could be selectively precipitate and grow. And also, the perovskite phase can be separated by the dressing method. The oxidation of molten slag gives off a large amount of heat, which helps chemical reactions proceed, improve the rate of chemical reactions, and promote the precipitation and growth of the perovskite phase. The features of the technique are clean, low cost and a great capacity to deal with a large quantity of slag. It was confirmed by experiments that the precipitation of the perovskite (CaTiO3) in molten slag is obviously affected by operation factors such as temperature, chemical composition, heat-treatment, additives and so on. The precipitating kinetics and mechanism of the perovskite phase from molten slag during the dynamic oxidation processes were also investigated.

Jan 1, 2006

By Sergei A. Degterov

A thermodynamic database for the slag, matte and liquid copper phases in the Cu-Ca-Fe-Pb-Zn-Si-O-S system has been developed for the ranges of compositions of importance to the production of copper. When used with the Gibbs energy minimization software and other databases of the F*A*C*T thermodynamic computing system, this database will permit the calculation of matte-slag-copper-gas phase equilibria that take place during copper smelting and converting. The calculations reproduce within experimental error limits all available experimental data on phase diagrams, activities of components, enthalpies of mixing, matte - alloy miscibility gap and tie-lines. The calculated solubilities of Cu in both S-free slag and slag equilibrated with matte are also in good agreement with experiment under all studied conditions, such as at SiO2 saturation, in equilibrium with Fe, Cu or Cu-Au alloys, at fixed oxygen or SO2 partial pressures and at different contents of Pb, Zn and CaO in the slag. Sulfide contents (sulfide capacities) of the slags are predicted within experimental error limits. The distribution of Pb and Zn among matte, slag, copper and gas has been calculated. The calculations are in good agreement with experimental data and predict the distributions under conditions which are difficult to study experimentally, such as at magnetite saturation or under various oxygen partial pressures and iron to silica ratios in the slag.

Jan 1, 1999

By Thomas M. Harris

To avoid the escalating cost of disposal of metals-containing wastewater and residues, new wastewater treatments will focus on the recovery of the metals. A combination of ion exchange and electrowinning can produce water suitable for discharge and relatively pure metals. The use of a chelating resin can enhance the selectivity of both the removal process and the elution of metals from the resin. A new, simple method of preparing a variety of chelating resins is being developed. The materials produced by this method exhibit interesting, as well as potentially useful, elution behavior. The performance of one test resin is described.

Jan 1, 1992

By Xiangru Chen, Qijie Zhai, Wei Zhang, Haicheng Li, Chao Yang

In this paper, ductile iron material with different content of niobium was prepared by a scientific melting method. Image Analysis Software was used to studied the effect of niobium microalloying on both pearlite content and pearlite lamellar spacing in ductile iron quantitatively. The results showed that the addition of a small amount of niobium could increase the pearlite content and decrease pearlite lamellar spacing of ductile iron effectively.

Jan 1, 2015

By R. L. Nyirenda

The use of ammoniacal ammonium carbonate (AAC) leaching for the treatment of carbon steelmaking EAF dust has been investigated on a laboratory scale. The experiments have been conducted on dust samples obtained from three European steelmaking companies. As received, the dusts were found to be toxic when tested according to current EPA toxicity testing procedures. Toxicity was on account of the leachability of one or more of the following elements: Ag, Hg, Pb, and Cd. Leaching experiments with concentrated AAC solution at 40 " C showed that zinc oxide present in the three dust samples, 60-80% of the total contained zinc, was rapidly solubilized. Data on the dissolution characteristics of Cd, Fe, Pb, Mg, and Mn are also presented. Toxicity tests conducted on residues of the leaching experiments found these to have leachates below past and current EPA toxicity threshold limits.

Jan 1, 1993

By Gerardo H. Achurra

During the last years, the Caletones Smelter, like others copper smelters in the world, has evolved from the conventional, inefficient, pollutant and expensive technologies, to modern, environmentally friendly and efficient ones. For this reason' as well as to improve its competitive position this Smelter shut down the reverberatory furnace, started up two big acid plants and has developed some pyrometallurgical technologies. The main facilities of the Caletones Smelting and Converting Process, in the present and the future, are the Teniente Converters, the reactors with a high operational availability that have reached concentrate top process capacities near to 2,400 tpd. These reactors operate in most of Chilean smelters as well as in other smelters in the world such as in Zambia, Peru and Mexico. Since 2000, the Caletones Smelting and Converting Process, has been adapted in two Teniente Converters, four Slag Cleaning Furnaces and four Pierce -Smith Converters. These facilities, together with the operation of two Fluidized Bed Dryers and two Oxygen Plants have allowed to reach concentrate smelting capacities and copper productions of 1,250 ktpy and 380 kfipy, respectively. Associated to EI Teniente Division Expansion Plan, Caletones Smelter, in the first stage, will increase its capacity to 1,440 ktpy in 2004. In the long term, Caletones has different options, such as the processing of 1,600 to 2,000 ktpy of concentrate, producing anodes, white metal or a mixture of them. These options are connected with CODELCO's Smelters & Refineries Strategic Plan, including Mejillones Project. The main challenges of Caletones Smelter are associated to the development and the consolidation of the Continuous and Environmental Friendly Processes, automation and control of different processes and to the improvement of its leadership between other Copper Smelters in the world.

Jan 1, 2003

By W. G. Davenport

This chapter shows how flash furnace industrial oxygen and oil requirements are affected by different: (a) product temperatures (b) conductive, convective and radiative heat losses (c) electrical energy inputs (d) hydrocarbon fuels. The calculations of the chapter are all for production of 65% Cu matte from pure CuFeS2 concentrate. Blast temperature is? 298 K throughout.

Jan 1, 2001

By M. Patel, G. Djambazov, J. Shrimpton

"Removing zinc by distillation can leave the lead bullion virtually free of zinc and also produces pure zinc crystals. Batch distillation is considered in a hemispherical kettle with water-cooled lid, under high vacuum (50 Pa or less). Sufficient zinc concentration at the evaporating surface is achieved by means of a mechanical stirrer.The numerical model is based on the multi-physics simulation package PHYSICA. The fluid flow module of the code is used to simulate the action of the stirring impeller and to determine the temperature and concentration fields throughout the liquid volume including the evaporating surface. The rate of zinc evaporation and condensation is then modelled using Langmuir's equations. Diffusion of the zinc vapour through the residual air in the vacuum gap is also taken into account.Computed results show that the mixing is sufficient and the rate-limiting step of the process is the surface evaporation driven by the difference of the equilibrium vapour pressure and the actual partial pressure of zinc vapour. However, at higher zinc concentrations, the heat transfer through the growing zinc crystal crust towards the cold steel lid may become the limiting factor because the crystallization front may reach the melting point.The computational model can be very useful in optimising the process within its safe limits.IntroductionLead bullion is commonly refined by removing various impurities (e.g. copper, silver, bismuth, antimony, etc) sequentially. This in normally achieved by the addition of reagents which selectively react with the impurities and the resulting compounds removed by various means. To aid efficient mixing (ensure uniform reactions), batch mixing of materials via the aid of impellers is common practice in a number of industrial sectors. Excess zinc, added during the desilvering process can be removed by one of three methods: (1) Vacuum dezincing - During vacuum dezincing, a vacuum is drawn on the agitated molten lead within a hemispherical vessel (Figure 1). Vaporized zinc condenses on the inner top surface of the vessel. The temperature at which zinc commences to vaporize lowers owing to heating under a vacuum. This enables vaporized zinc to be recovered in the form of high purity crystals without oxidation. The zinc crystals are recovered once the vessel lid is removed and the vacuum is broken. (2) Chlorine dezincing - In chlorine dezincing, molten desilvered lead is reacted with chlorine gas, forming a surface layer of zinc chloride contaminated with small amounts of lead chloride."

Jan 1, 2004

By KNona Liddell

Many metal recovery processes Involve heterogeneous reactions In porous media accompanied by fluid flow and mass transfer. Modeling such systems Is difficult because of the number of rate processes Involved and is complicated even further by effects due to the structure of the porous medium. Data on even bulk properties of the medium are often severely limited or unavailable. For many such systems, a cell model may provide, an attractive alternative to models based on transport ,mechanisms in a differential volume. A cell model requires less input data and is computationally efficient. Identical residence time distributions can be obtained with models of both types, and both allow conversion and concentration profiles and histories to be calculated. The formulation and properties of cell models for metals recovery are described in detail.

Jan 1, 1996

By Donald J. Hallbom

Limonitic nickel laterites slurries exhibit complex rheological properties including time dependency that varies from thixotropy to rheopexy. Chronic problems may occur if plant designers and operators fail to take time dependency into account. Stress decay tests indicate that laterite slurry takes roughly two minutes to approach steady state after a step change in the shear rate. As a result, most rheometer measurements are taken at a non-equilibrium state, making evaluation difficult. Two minutes is also long relative to the time that a unit of slurry in a processing plant is at any given shear state, so the slurry may never reach equilibrium. This paper presents a method to describe the rheology of laterite slurry using a Flow Array, which describes the rheology using an array of instantaneous flow curves crossed by an equilibrium flow curve. A rate equation for structural change in non-equilibrium conditions allows time dependence to be efficiently modeled. This flow array allows the flow behavior of time- dependent slurry to be predicted in non-equilibrium conditions using a simple time-step methodology. Keywords: Rheology. nickel laterite, hydraulic transport, pressure acid leach, flow array

Jan 1, 2004

By S. Eckert, G. Gerbeth, K. Timmel, B. Willers, T. Wondrak, N. Shevchenko, M. Röder

The quality of the produced steel in the continuous casting process is significantly governed by the melt flow in the mold. However, direct flow measurements in liquid metals are still rather scarce. In order to investigate these flow phenomena, three experimental facilities operating with low melting liquid metals were installed at Helmholtz-Zentrum Dresden-Rossendorf (HZDR). The melt flow in the models is measured by the Ultrasonic Doppler Velocimetry (UDV) or the Contactless Inductive Flow Tomography (CIFT), multi-phase flows can be visualized by X-ray imaging. The obtained measurement results are primarily used for validation of numerical models. In this paper we will investigate the fluid flow in the mold and the behavior of the surface of the liquid metal using flow measurements by UDV and surface profile measurement by a laser scanner, respectively. Strong fluctuations and deviations of the free surface were observed in case of a static magnetic field

Jan 1, 2016

By M. A. Cocquerel

External process energy requirements and air pollution control regulations formulated to limit particulate and SO2 emissions are impacting on smelting and converting technologies and the corresponding process and secondary gas handling systems. This paper presents an overview of the different technical solutions used for cooling and dedusting the process gases in the different pyrometallurgical copper concentrate stages, including: drying, smelting, converting, slag cleaning and fire refining. The main principles of the process gas handling systems are presented &d a qualitative technical and economical comparison is discussed in relation to process changes, energy recovery and marketing or disposing of the various sulfur fixation by-products. Finally, a brief review of the methods for fixing sulfur contained in the process and secondary gases is presented.

Jan 1, 1999

By Christina Viklund-White

Life Cycle Assessment has been used to compare the environmental performance of landfilling versus recycling of the zinc used for galvanizing steel. Hypothetical process routes were com-posed involving four different EAF dust treatment processes; Waelz kiln, DC-furnace, EZINEX and slag fuming, as well as scrap dezincing. The study shows that recycling of zinc used for galvanizing steel has environmental benefits in that it saves zinc resources. However, zinc recovery does not necessarily decrease the potential impact on global warming and acidification. The magnitude of these two impact categories is tightly correlated with the amount and type of primary energy consumed in a process. Due to the high electricity consumption in the dezincing process, this route has the highest impact on Global Warming Potential as well as Acidification Potential. The major part of the energy requirement for the production of zinc from primary and secondary sources is consumed in the reduction of ZnO to Zn. The consequence is that the theoretically possible savings in primary energy by recycling zinc-containing materials are relatively minor. The impact categories "land use" and "waste generation" are not considered in this study, but most likely the evaluation of such impacts would further increase the potential environmental impact of the landfill alternative. The results also show that the location of an electricity-intensive process highly affects the potential environmental impact. Comparing process and material alternatives in LCA studies where branch average data is used, is considerably more complex than when LCA is used within a company.

Jan 1, 2000

By K. Olsen

As aluminum alloy usage in automobiles grows, there are increasing demands on recycling processes and facilities to deal with mixed alloy automotive aluminum scrap. These processes and facilities strive to produce near virgin aluminum stock, which can be relatively costly and difficult. One alternative is to use physical processing methods to upgrade the scrap properties instead of chemically refining the scrap. The Impulse Atomization Process (LAP, patent pending) is a new process for making metallic and ceramic powders. It can produce fine homogeneous microstructures in scrap aluminum alloys due to high undercooling and rapid solidification. The particles have a very narrow size distribution and are in a convenient form for consolidation. This paper compares and contrasts the microstructural features of Impulse Atomized. and quenched Impulse Atomized powders,' for both AL6061 and a scrap aluminum alloy composition.

Jan 1, 1995

By Jinqian Zhao, Jiarong Li, Shizhong Liu

"Creep cavitation of in single crystal (SX) superalloy was investigated. The constant load creep tests, in single crystal superalloys DD6, were conducted at the conditions of 800°C/700MPa, 850°C/550MPa and 900°C/450MPa, respectively. It was found that there were square facets on the stress fracture surface, and microscopic cavities in the ruptured specimens in the vicinity of the fracture surface. Both the square facets on the fracture surface and microscopic cavities in the section of the ruptured specimens show the morphology of the same thing at the different views, namely creep cavities, which are take the form of flatten cuboid. In fact, creep cavities are the longitudinally tensiled creep cracks slowly growing during the stress tensiling. The factors of creep cracks nucleation and growth conditions include: (a) enough high temperature to activate diffusion (b) casting pores as nucleation origination (c) high strains and strain rates. Eventually, the instantaneous fracture mechanism of creep specimen is cleavage fracture.IntroductionFor the materials used in elevated temperature service, creep behavior has to be accounted for. It is well recognized that creep rupture in polycrystalline materials at high temperature occurs principally by the nucleation and growth of microscopic cavities at grain boundaries, followed by microscopic cavities linkage to form micro- and eventually macro-intergranular cracks[l,2]. Without the usual grain boundaries, SX superalloys have superior capabilities at high temperatures to polycrystalline superalloys, and have become an established feature of gas turbine technology where they are commonly employed in the manufacture of high performance blades[3]. A considerable amount of work has been done over the past tens of years, and many models for nucleation and growth of creep cavities have been proposed, however, those are mainly for polycrystalline materials.In order to improve creep resistance that single crystal superalloys, in which grain boundaries are removed, have been developed. Because there don't exist grain boundaries in SX superalloy, the mechanism of nucleation and growth of creep cavities must be different from that in polycrystalline materials.Understanding the formation and characteristics of creep cavitation is crucial to model the lives of single crystal superalloys.M. Marchionni and L.G. Zhao et al. found that there were square facets on the stress fracture surface [4,5]. Roger C. Reed pointed out creep cavities lie in the necked region[6]. In this paper, the effects on the formation of creep cavities are discussed, as well as the morphology of creep cavities and fracture mechanism of SX superalloys."

Jan 1, 2013

By Leonard A. Duval

This concept employs a viable energy saving method that uses a solvent to separate oil from particle matter; it can be used in metal forming industries to deoil sludges, oxides, and particle matter that is presently committed to landfill. If oily particles are used in their oily state, severe consequences to environmental control systems such as explosions or filter blinding, occur in the air handling equipment. This is due to the presence of hydrocarbons in the stack gases resulting from the oily particles. After deoiling, the particles can be recycled and the separated oil can be used as a fuel. The process does not produce a waste of it's own and does not harm air or water. It demonstrates the dual benefits of being commercially viable and in the national interest of conserving resources.

Jan 1, 1994