Search Documents

By Donald Voit

"The reaction between zirconia/zircon, coke, and chlorine involves a slow reaction between the coke and the zirconia/zircon and a fast reaction with chlorine. Because of the fast chlorine reaction, the reaction rate for zirconia/zircon is nearly independent of chlorine concentration for most conditions. The reaction between zirconia/zircon and coke is particle size controlled and related to the degree of physical contact between the zirconia/zircon and the coke. Since particle-particle contact is critical, compaction of finely ground coke and zirconia/zircon produces the highest reaction rates. Uncompacted, coarse coke and zirconia/zircon has the slowest reaction behavior with static bed tests.SummaryZirconia reacts with chlorine in the presence of carbon to form zirconium tetrachloride, carbon monoxide, and carbon dioxide. A similar reaction occurs with zirconium silicate with the additional formation of silicon tetrachloride. The reaction rate depends primarily on temperature and the intimacy of contact between the zirconia and the coke. The reaction is multi-stepped with a slow reaction between coke and zirconia to form an intermediate that reacts rapidly with chlorine, causing the order of the reaction for chlorine to be near zero. Chlorination rates in the range of 1 µmole/hr/cm2 are seen for fluid bed reactors. Plug flow, and static bed reactors have reaction rates of the order of 1 mmole/hr/cm2, where the area is based on the zircon surface area in plug flow and fluid bed reactors and the boat cross sectional area in a static bed. Chlorination rates measured in zirconia/coke briquettes are higher with rates as high as 400 mmole/hr/cm2 reported. High chlorine diffusion resistance, not accounted for in the analysis of experimental results, has led to a lot of confusion in the literature interpretation of chlorination data.In general coke and zirconia/zircon particle size, coke and zirconia/zircon intimacy, coke to zirconia/zircon ratio, chlorine concentration, and temperature are important variables for chlorination. Decreasing the coke and zirconia/zircon particle size generally increase the reaction rate. The coke to zirconia/zircon ratio affects the reaction in a more complex way. Increasing the chlorine concentration generally increases the reaction rate, but the effect appears to be more related to the concentration dependency of diffusion than to its role in the kinetics. The reaction rate increases with temperature but the exact behavior is complicated by temperature effects on diffusion."

Jan 1, 2011

By Robert G. Telewiak

During the past few years, the international nickel industry has taken some important steps to respond to conditions of global production overcapacity, relatively flat demand and low prices. These include the implementation of major cost reduction programs by most producers, closure of some high cost operations and the establishment of the Nickel Development Institute. Consumption in the western world increased by about 7 per cent in 1987 compared to 1986, supplies were less than demand, inventories were low, and late in the year prices increased dramatically. By year-end 1987, most producers were operating at, or close to, their effective capacities. Nickel demand is expected to increase to the year 2000 at an annual rate of about 1.7 per cent, led by increasing usage in the stainless steel sector. If this rate of growth is realized, then there will be need for the effective capacity of the nickel industry to be increased. Producers in Canada have put considerable effort in the past few years into reducing costs - with impressive results. Mining costs, in particular, have been reduced dramatically. While production is still less than the peak years of the yearly 1970's, it has increased substantially from levels of the early 1980's. Over the next few years, production is expected to increase slowly. A key determinant of the level of production in the 1990's could be the effect that regulations on sulphur dioxide emissions have on limiting production.

Jan 1, 1988

By Hans Jürgen Maier, Hans-Bernward Besserer, Gregory Gerstein, Florian Nürnberger

The formation and development of voids in both the single-phase ferritic steel DC04 and the dual-phase ferritic-martensitic steel DP600 are discussed. Various mechanisms and kinetics of void formation are considered regarding the influence of dislocation glide, precipitates and other parameters. Different characteristic locations in the microstructure are investigated at which strain concentrations during plastic deformation can occur and cause the formation of voids and microcracks. For the specimen preparation ion slope cutting is applied. Voids and cracks revealing ductile damage are analyzed by Scanning Electron Microscopy (SEM). Stress concentrations in consequence of plastic deformation could be shown by extinction contours on images recorded by Transmission Electron Microscopy (TEM).

Jan 1, 2015

By S. N. Ojha, Gouthama, R. K. Mandal

"Spray deposition processing of liquid immiscible alloys, based on AI-Pb and Cu-Pb systems have been investigated. Process variables have been optimized to generate uniform dispersion of ultrafine second phase particles in· the matrix of the primary phase. Mechanisms governing the microstructural evolution in this synthesis methodology are discussed. Results of the present investigation are used to demonstrate that rapid solidification of atomized droplets initially provides a high nucleation rate of the second phase during the liquid phase separation. The solid matrix phase nucleates at a later stage and grows with a high velocity enabling trapping of the dispersed phase. Subsequent alteration in the size and size distribution of the second phase is suggested to arise further during deposition of high velocity droplets. Possible reasons for this effect are brought out. Microstructural features of atomized powders and spray-deposits of these alloys are presented to support the present approach of synthesizing composites. IntroductionIn recent years, synthesis of advanced materials with metastable microstructures and ultra fine dispersion of second phase particles has led to the development of novel techniques of materials processing. The other requirement of such a processing methodology is to achieve near-net shape geometries in less number of processing steps. The solidification processing method via spray deposition route qualifies these criteria. This process primarily involves atomization of a melt by high energy gas jets into spray of droplets which are subsequently propelled by the kinetic energy of the gas towards a deposition substrate to build-up a thick high density preform. Although the concept of spray deposition was pioneered by Singer [1] in the early seventies, the fundamentals of the deposition process has been understood only recently [2-4]. Several benefits of spray deposition processing are by now well established [5,6]. Rapid solidification effects are inherent in spray deposition processing due to high heat exchange rate at the droplet-gas interface and also on the deposition surface by force convection. Since considerable heat extraction occurs from the atomized spray prior to droplet consolidation, a relatively low processing temperature is ensured in this process. As a result deleterious coarsening phenomenon can be minimized. In addition, controlled maneuvering of the substrate provides the capability of the process in producing disc, sheet or tube shape preforms of difficult to work materials in a single operation. A significant improvement in properties, resulting from microstructural homogeneity and refinement in grain size induced by spray deposition has been reported for several alloy systems [7,8]."

Jan 1, 1994

By Ajay K. Singh

The surface quality demands for galvanized and galvannealed steel sheets by the automotive and appliance industries have been getting increasingly stringent over the past few years. Intensive efforts by Hot-Dip-Galvanizers to meet these demands have resulted in substantial improvement to the hot dip coating process. However, elimination of zinc bath contaminants which directly affect the coated strip surface quality continues to remain a tough challenge. As part of our effort to improve the zinc bath cleanliness, Inland Steel Company has developed a test method to quantitatively measure the contaminants in incoming zinc spelters and establish a specification for incoming zinc quality. The test is currently being used for auditing the incoming zinc quality. The zinc suppliers are also using this test for quality control purposes. The purpose of this paper is to describe the test method and how it has improved the galvanizing operation at Inland.

Jan 1, 1992

By Do-Hyeong Kim, Tae-Jung Kim, Seung-Yeon Won, Jong-Jin Pak, Min-Kyu Paek

Liquid iron alloys containing V, Mo, and Ni can be produced by the carbothermic reduction of spent catalysts used in petrochemical industry. Thermodynamics of carbon in these alloy melts is important for refining these alloys. In the present study, the carbon solubility in Fe-V, Fe-Mo, Fe-Ni, Fe-V-Mo, Fe-V-Ni, Fe-Mo-Ni and Fe-V-Mo-Ni alloy melts of various compositions was measured at 1873 K. The temperature dependency of vanadium effect on carbon solubility in liquid iron was also measured in the temperature range from 1823K to 1923K. The additions of vanadium and molybdenum significantly increased the carbon solubility in liquid iron alloys while nickel decreased the solubility. The experimental results were thermodynamically analyzed using Lupis’ relation at constant activity to determine the first- and the second-order interaction parameters of vanadium, nickel and molybdenum on carbon at carbon saturated condition. Using thermodynamic parameters determined in the present study, the carbon solubility in Fe-V-Mo-Ni alloy melts of various composition were accurately predicted and verified experimentally at 1873 K.

Jan 1, 2014

By Jesus Gonzalez

Peirce-Smith converters (PSC) are long cylindrical chemical reactors where copper matte reacts with air. Traditionally, air is injected laterally through submerged tuyeres at different subsonic velocities. However, the accumulated experience in steelmaking, particularly in the basic oxygen furnace (BOF) process, shows that the gas bottom injection may improve the mixing efficiency of a liquid pool. The aim of bottom injection is to maximize the copper kinetic energy meanwhile avoiding excessive reactor splashing. When gas is injected from a single orifice at the bottom of a liquid pool, two main gas flow regimes can be identified, bubbling and jetting. In this work, a PSC with bottom air injection is studied by means of multiphase 3D CFD numerical simulations considering multiple air velocities. Special attention is paid to the bubbles and jet formation mechanism. The mixing efficiency is measured by calculating the turbulent kinetic energy of the copper matte.

Jan 1, 2008

By Susanne Pignolet-Brandom

QEM*SEM is an automated scanning electron microscope/computer system that characterizes samples with regard to mineral modal abundances, mineral grain and particle sizes, mineral associations, and particle surface areas. Additional information, based on the classification of particles according to the area percentage of a mineral of interest, can be obtained for samples of particulates. QEM*SEM is capable of analyzing a wide variety of materials although it was originally developed for applications to the minerals industry.

Jan 1, 1988

By R. W. Smith

The flotation response and electrokinetic behavior of Chlorella vulgaris and Chlamydomonas sp . when using dodecylamine hydrochloride as collector were studied in the absence and presence of Pb(I1). Also, an electron microscopy study was made of the algae after Pb accumulation. The flotation behavior of the organisms after Pb accumulation appears at least partially related to the location of the abstracted Pb onto or into the organisms.

Jan 1, 1991

By Ma Ying

The continuous directional solidification technique of five kinds of special ZA alloys with eutectic, peritectic and eutectoid transfonnation under the condition of continuous casting by heated mold was studied. The mechanism of surface defects appearing in ZA alloy line was discussed and the structure of some defects were analyzed by SEM. The results show that only when the fitting of various technique factors, pressure head, outlet temperature, pulling speed and cooling condition are reasonable under a certain range, can the ZA alloy smooth line be continuously pulled out. Unreasonable techniques will result in hot tear, rough surface, mush outlet, leaking and other defects. The shape and location of solid-liquid zone have an important influence on the formation of the above defects. When the solid-liquid zone is located in the mould outlet or inner mould, the surface of solidification will protrude into the inner mould. If the remaining liquid cannot counteract the solidification contraction, a rough surface will appear. If the solidification surface further into the mould, the ingot in the mould will have a great friction force when pulling and will form a hot tear. When the solid-liquid zone is moved out of mould, the solidification surface will turn into a plane, which easily results in leaking. A vibration or unstable operation will cause an ingot winding during pulling.

Jan 1, 2003

By J. E. Allen

The trend in refractory technology for the copper and nickel industries has been to higher quality raw materials and improved processing technology. These changes have been dictated by the changes in pyrometallurgical processes in these industries. For example the introduction of flash smelting, reaction type smelting and auxiliary slag cleaning furnaces havedemanded better refractories materials. Extensive field applications and improved laboratory testing procedures have helped make this transition possible. Changes in refractory technology, primarily in basic refractories, are followed from the late fifties to the present and into the future.

Jan 1, 1994

By Kumar M. Lyer

Residence time distribution (RTD) of light and heavy liquids in a pyrometallurgical channel reactor was mathematically modeled by representing the reactor as a combination of ideal reactors. Cold model studies simulated the counter-current flow of slag and matte (or metal) with high-strength bottom gas injection. The experimental variables include flow rates, heights, density and viscosity of the two liquids; gas flow rate; injector diameter; and distance between injectors. The experiments covered a wide range, of the appropriate dimensionless parameter, including conditions in ferrous and nonferrous extractive metallurgy. Dispersion modeling studies were also carried out to determine the degree of backmixing. Results indicate that the degree of backmixing in the channel reactor for various operating conditions corresponds to that for 3-20 perfectly mixed reactors in series.

Jan 1, 1993

By Suleyman Tekeli, Serdar Salman, Bulent Aktas

"The effect of La2O3 content up to 15 wt% on phase stability, sintering and microstructure of cubic zirconia (8YSZ) was investigated. XRD results showed that the specimens containing up to 15 wt% La2O3 were composed of only cubic structure. Also, the specimens doped up to 5 wt% La2O3 revealed no La2O3 peaks, indicating that La2O3 was completely solubilized in the cubic structure. However, when> 5 wt% La2O3 was added, the peak of La2Zr2O7 compound emerged, showing that the overdoped La2O3 was not solubilized in the 8YSZ matrix. The lattice parameter of the 8YSZ slightly decreased with the increasing La2O3 content up to 1 wt% but further increase in the La203 amount resulted in an increased lattice parameter. The comparison of grain size of the 8YSZ specimens with various La2O3 content showed that grain size slightly increased with the increasing La2O3 content up to 1 wt% but further increase in the La2O3 amount resulted in a decreased grain size.IntroductionAt atmospheric pressures, three polymorphic forms of Zr02 are stable at different temperatures i.e. monoclinic, tetragonal and cubic. A high-pressure orthorhombic form of Zr02 has also been reported[l]. The successful production of pure Zr02 bodies is not possible all the time due to the large volume expansion associated with the martensitic tetragonal-monoclinic transformation. This fact restricts the applications of zirconia, in spite of its excellent mechanical and thermal properties. However, the stabilization of the high temperature polymorphs at room temperature as stable phases is made possible by addition of suitable dopants. Fully stabilized cubic Zr02 and partially stabilized tetragonal Zr02 show interesting properties and are widely used as ionic conductors, coatings and gas sensors in solid oxide fuel cells and structural applications[2]. Most frequently used dopants include Y203, CaO, MgO and Ce02, although other oxides, such as those of rare earth elements, can also act as stabilizers of the high temperature structures. The incorporation of aliovalent cations to the lattice, forming substitutional solid solutions, allows to control the concentration of anionic vacancies in the structure. This aspect is particularly important in designing ionic conductors[3], and is also determinant in the stabilization process[ 4]. The process of stabilization with larger ionic radii dopants is rationalized by the crystal chemistry model[ 5], that describes the dopant cations as typical stabilizer when they have larger ionic size, lower charged state and higher ionicity than Zr4+ The ionic radius of Zr4+ is 0.84 Å and that for La3+ is 1.016 Å [6]."

Jan 1, 2012

By Lei Zhang, Shining Chen, Lina Wang, Pu Liu, Benquan Fu, Jiannyang Hwang

A three-dimensional (3D) electrode reactor combined with Fenton reagent was used for advanced treatment of coking wastewater from secondary biological treatment. Effects of some key factors on total organic carbon (TOC) removal rate were investigated, and the results were compared with those of the common three-dimensional electrode reactor. Experimental results showed that TOC removal rate could reach 51.7%, when optimal operating conditions were as follows: initial pH value 3.5, H2O2 dosage 17.6mmol/L, reaction time 90min and FeSO4·7H2O dosage 3.5mmol/L. Analytical results from UV absorption spectra indicated that the organic substances in the coking wastewater were well degraded by this system, which provided good experimental basis for the practical application of this process in the treatment of coking wastewater. This can be meaningful for the treatment of other kinds of wastewater.

Jan 1, 2015

By J. E. Murphy

Neodymium was electrowon into a Mg-Cd molten cathode at 650 °C from NdC1,-KC1 electrolyte. With the chloride system, neodymium was deposited into the molten alloy cathode until the neodymium concentration reached 20 wt pct. The alloy was then vacuum melted to remove the Mg and Cd. The current efficiency exceeded 80 pct under optimum conditions and the purity of the metal was 99.9 pct after vacuum melting. As an alternative approach, neodymium was electrowon at 1,030 °C from Nd,O, dissolved in a molten fluoride eleotrolyte. With the oxide-fluoride electrolyte, the metal was electrowon in a molten state with current efficiencies up to 60 pct. The purity of the metal was 99.8 pct with oxygen and carbon as major impurities. A number of problems were encountered including anode effect, low oxide solubility in the electrolyte, high neodymium metal solubility in the electrolyte, and reactivity of the metal with the cell materials. Approaches to improved cell, operation and prospects for commercial adoption of the electrolytic production of neodymium metal are discussed.

Jan 1, 1995

By Mansoor Barati, Leili Tafaghodi Khajavi

"This study involves employing solvent refining as a purification process in which silicon recrystallization takes place from an iron-silicon melt. It is believed that iron will act as the impurity “getter” and purified silicon crystals will grow from the alloy melt, while the impurities are segregated to the liquid alloy. Phosphorous is a problematic impurity to remove since its segregation coefficient in pure silicon is relatively large. To assess the feasibility and efficiency of phosphorous removal through solvent refining, it is critical to study its equilibrium distribution between solid Si and the Fe–Si alloy phase.The distribution of phosphorous between solid silicon and iron-silicon melt at 1210-1310 °C was measured to evaluate the impurity removal potential of each alloy. Interaction parameter between phosphorous and iron was calculated by varying the concentration of phosphorous in silicon.IntroductionAmong various semiconductor materials for manufacture of solar cells, silicon accounts for over 90 percent of today's PV materials [1, 2].The major challenge in producing solar silicon that operates efficiently is to meet purity level requirement through a cost efficient route. Silicon solar cells can play a significant role in answering the world's need for energy if cost reductions can be achieved through manufacturing process. Considerable effort has been made to replace the expensive, complex vapor-phase purification by a simpler and less costly process. One of the refining approaches that have attracted wide research interests is producing low-cost solar grade silicon by purification of metallurgical grade silicon. Since metallurgical processes are selective in removing impurities, a combination of various purification processes can be used to reduce the impurity level in silicon. Considering different thermodynamic characteristics of impurities, each refining step is responsible for lowering specific impurities."

Jan 1, 2012

By Guo Chang Jiang

In order to improve the IIAZ toughness of X-60 pipe steel, the intragranular ferrite plate (IFP) technology was used. The characteristics of IFP is claimed to be much fine ferrite plates appear inside the original austenite grains. By means of suitable Re, Zr, Ti additions in a bath with a higher initial oxygen potential, a good control of the peak temperature and the cooling rate during welding simulation, one can get a %IFP in volume over 50%, and the toughness gets up from 55 J to 160 J. It was found that the inclusions most effective in nucleating IFP are some deformable complex silicates which either entrap Re, Zr, Ti oxides or contain these elements. The greater the number of the evenly distributed and effectively nucleating inclusions, the more the %IFP in volume, and the finer the microstructure of the HAZ, so the better the relevant toughness. Generally, these silicates bahave as fine spheres along a line. The present authors revealed that these fine spheres result from the remelting of the shuttle- like silicates due to heating in the process of welding simulation. These silicates used to get a higher sulphur capacity, so MnS deposits might be observed on the periphery of the silicates. IFP was proved to be directly rooted in the [Mn] depleting zone which locates beside MnS deposits.

Jan 1, 1997

By Y. Ono

In lightweight metal processing such as aluminum (AI) and magnesium (Mg), metal cleanliness is a crucial process parameter for refining, part manufacturing and recycling in order to obtain high quality parts and products. In this paper, techniques for cleanliness evaluation of molten AI and Mg using ultrasonic probes with clad steel buffer rods having high signal-to-noise ratio (SNR) are presented. Due to the high SNR of the ultrasonic probes used, backscattered ultrasonic signals from inclusions, which may be oxide films and/or particles, in molten Mg and those from silicon carbide particles, having an average size of 50f.Ull, added in molten AI are successfully detected with reflection configurations of pulse-echo and/or pitch-catch modes at an ultrasonic frequency of 10 MHz. In addition, relative cleanliness evaluation of molten Al and Mg is demonstrated. In order to establish the procedure and to investigate the optimum system configurations for cleanliness evaluation of molten metals, particle flow simulation system using water and polyvinyl chloride (PVC) particles has been constructed. Counting the number and measuring the size distribution of the PVC particles, having an average diameter of 128um, suspended in water with the PVC volume concentrations of 5ppm and 10ppm are performed with ultrasonic pitch-catch mode. The counted numbers of particles by the presented method and system have good agreement with the calculated results with a count error of less than 10% or two counts. Based on the results obtained with water simulation experiments, the prototype system for cleanliness evaluation of molten Mg by counting and sizing inclusions has been developed. Keywords: Ultrasound, Clad buffer rod, Molten metal, Aluminum, Magnesium, Inclusion detection, Cleanliness measurement, Counting, Sizing

Jan 1, 2003

By S. K. Utimurd, D. C. R. Espinosa, J. A. S. Tenório

"Waste Electrical and Electronic Equipment (WEEE) has become an environmental issue due to technological advance and waste plastic is one of the main polluters. The excessive discard of these plastics result in a difficult to dispose it to landfill and need further separation with technique in order to produce high added value plastics. There are many kinds of plastics in extensive use at the present time and the co=on are the acrylonitrile-butadiene-styrene (ABS) and high impact polystyrene (HIPS) used in the production of electric appliances. These plastics are difficult to separate because they have similar densities. Flotation of plastics is one possible separation technique and using selective wetting agents. The separation may be possible given close control at particle size and the concentration of the reagent. The process was able to produce a concentrate of HIPS with at least of 93% purity and a concentrate of ABS with 99% purity.IntroductionThe current situation of municipal solid waste (MSW) management especially in emerging economies like Brazil, the growing population and economic activity will result in a significant increase in the generation of waste in the coming decades. It is worthwhile to review and update the sources, amounts and recovery technologies of specific materials from waste, particularly from municipal solid waste (MSW).The growing impact of the current waste management practices stresses the need for a change in how waste is handled. The 2012 survey and the Brazilian Association of Public Cleaning and Special Waste Disposal Companies (ABRELPE) reports the generation of 62 Mt urban MSW in that year, which is an increase of 13% compared to 2011. It has been reported that in Brazil about 90.17% of the generated MSW is currently collected, which indicates an increase in the coverage of collection services compared to 2011 [ l]."

Jan 1, 2014

By Wolfgang Steffes-Tun

Pyrite ore concentrate from the Meggen mine (FRG) , which contains about 0 300 400 ppm thallium, is roasted in a fluid bed furnace at 1000 -1100 C to form sulfur dioxide and ash consisting mainly of hematite. Subsequently, the sulfur dioxide is separated from the ash or dust during several steps while cooling to about 250oC. The pyrite ash fractions show decreasing grain size down to 5 pm, a pH-decrease down to 2,4 and a marked enrichment of arsenic and thallium by a factor of 12. In the final fraction, the hot electroprecipitator dust of the dump (EGR), minute crystals of thallium-containing jarosite can be detected by analytical transmission electorn microscopy (TEM). Under oxidizing, acid conditions, jarosite may be a possible "reservoir mineral" for immobilizing thallium.

Jan 1, 1989