Search Documents

By Kenneth L. Driggs

The 1988 shift in primary smelting facilities from low grade matte (35%) reverberatory furnaces to high grade matte (63%) flash smelting heavily impacted a very stable and successful converter operation. Low matte grade converter campaigns averaged 36,000 short tons of copper and revert production/consumption was in balance. The conversion to high matte grades necessitated oxygen enrichment of converter blast and revisions in operating practices. After two years of operational development, campaign life has risen to over 40,000 short tons and revert production/consumption is again in balance.

Jan 1, 1991

By Gopalakrishna B. Prabhu, David L. Bourell

"Three mol% Yttria-Stabilized Tetragonal Zirconia (YSTZ) was prepared by a sol-gel synthesis technique using zirconium tetrachloride and hydrated yttrium chloride precursors. After drying and annealing at 823K, the particle size was in the range 10 to 20 nm. The zirconia powder was sintered using a uniaxial hot press at an applied stress of 20 to 40 MPa. One hour, isothermal sintering was performed in air after initial heating at 50K/min. Theoretical density was obtained at densification temperatures above 1498K. After sintering, grain coarsening characteristics were studied using constant heating rate anneals followed by quenching, based on a model for grain coarsening in a linear heating rate cycle. The microstructural change was studied using SEM and TEM and the phases were determined using x-ray diffraction.IntroductionThe ability to sinter nanocrystalline materials to full density several hundred degrees below the normal sintering temperatures is one reason for their current interest. [1-5] Yttria Stabilized Tetragonal Zirconia (YSTZ) of grain size of about 300 nm has exhibited superplasticity, with elongations as large as 800%.[6-7] Fine grain size is critical for superplasticity. Retention of the fine grain size during sintering of nanocrystalline powder is important if a material is to exhibit superplasticity or to exhibit physical or mechanical properties associated with the ultra fine structure. This paper investigates the sintering behavior and the grain coarsening characteristics ofnanocrystalline YSTZ.Techniques for synthesizing nanocrystalline materials have been studied in great detail earlier. [8-12] The techniques used to synthesize nanocrystalline zirconia include alkoxide synthesis [9], the chloride method [11], the peroxide method [13] and the acetone-toluene method. [13] In this paper the method used in the synthesis of zirconia is the chloride technique. With this precipitation technique, either zirconium chloride or oxychloride and a corresponding yttrium salt or even pure yttria are used."

Jan 1, 1994

By Suzanne Young

The effect of LiF additions on liqt.1id1.:1s temperature and electrical conductivity over a wide range of cryolite bath ratios (1.0 to 1.5 weight ratio) was investigated. Results did not agree with multi-regression equations reported by Dewing and Choudhary over the entire region. New regression equations were developed. Reasons? are given for the differences. The models are used to discuss the economic implications of LiF additions to Hali cell electrolytes.

Jan 1, 1985

By D. Y. Wang, G. Y. Sha, X. L. Shen, D. R. Gu

The study of the volatilization kinetics of zinc and lead in pellets made of zinc-leadbearing dust mixed with coal powder, in a nitrogen atmosphere and at a temperature range between 1100 °C and 1300 °C, shows that the reduction temperature has a significant effect on the volatilization rates of zinc and lead, and that both the particle size of the coal powder and the extra carbon content has no effect on the volatilization rates. The obtained activation energies for the volatilization of zinc and lead are 79.42kJ/mol and 88.74kJ/mol respectively. The volatilization rate of zinc is controlled by the reaction between the zinc oxide and carbon monoxide while that of lead is controlled by the lead evaporation reaction, and the diffusion of gaseous lead through the gas boundary layer covering the surface of the reduced liquid lead.

Jan 1, 2000

By Vaughan R. Voller

"Numerical methods for dealing with a temperature dependent conductivity are discussed. An approach based on a local application of a Kirchhoff transformation at the discrete level is presented. The application of this transformation - that does not require any inversion- is demonstrated on solving a two-dimensional test problem.IntroductionMuch is said in the recent literature on the modeling necessity of obtaining appropriate thermo-physical properties; in particular the requirement to account for properties that are ""strong"" functions of the depended variables, e.g., Temperature. Of course obtaining appropriate thermo-physical properties serves no purpose unless they can be accurately integrated into a discrete numerical calculation. The purpose of this paper is to examine how temperature dependent conductivities that exhibit discontinuities or rapid changes can be handled in a numerical code.The discussion will be made in the context of a control volume finite element method [1]. After a brief outline of control volume finite element fundamentals basic methods of dealing with discontinuous or rapidly changing thermal conductivity are discussed. This is followed by the presentation of the recently proposed local Kirchhoff method [2,3], The paper concludes with an investigation of the performance of the various conductivity schemes in solving two dimensional problems. This testing clearly shows the advantages (accuracy and implementation) in using the local Kirchhoff method."

Jan 1, 2001

By N. Moelans

A method using an ex-situ electrochemical measurement device was developed to determine the oxygen potential of non-ferrous metallurgical slags. The electrochemical cell consists of the molten slag sample, an inert Ir electrode, a stabilized Zr02 solid electrolyte and a NiINiO reference electrode. Different slags from non-ferrous pyrometallurgical processes were analysed at 1100 and 1200°C and pO2 values between 10-3 and 10.12 bar were obtained. The measurements were evaluated with? thermodynamic calculations and using processing considerations. It was found that the reproducibility and stability of the measurement was significantly improved by shielding the molten slag from the atmosphere by a thin layer of carbon, especially for slags with a low oxygen potential.

Jan 1, 2003

By Luísa Maria Abrantes

Environmental control is becoming more and more stringent. As conventional processes for zinc production are pollutant routes, alternative methods have become an important subject of research. In this regard, the leaching processes have aroused a considerable interest, namely the electrochemically induced approach. The behaviour of zinc concentrate ore in the leaching processesses is influenced by several parameters. Chloride concentration and leaching solution pH, time and temperature of reaction were studied in order to evaluate their influence on the zinc recovery. The efficiency of the leaching process for zinc extraction is performed by factorial design. The experiments were carried out by 23 and 22 factorial designs of the factors. Results show that all factors, except for the time of reaction have a significant influence on the optimisation process, within each experimental region.

Jan 1, 2001

By Zhen Zhang, Jiang Diao, Xuan Liu, Tao Zhang, Bing Xie, Hong-Yi Li

Extracting vanadium from vanadium containing hot metal by LD process has been proven an effective solution for the utilization of vanadium-titanium magnetite ore, but the systematic analyses of vanadium extraction rate and mechanism by basic slag are seldom reported. In this study, mathematical model of vanadium transfer from metal to slag was formulated and the rates of vanadium extraction of hot metal with basic slag were investigated. The results indicated that the apparent vanadium extraction rate constant, kp, were in the range of 1.33~9.07×10-4g/(cm3·s). And the rate constant was increased with the increase of final slag basicity, reaction temperature and stirring gas flow. The apparent of mass transfer parameter decreases significantly from 0.13 cm3/ s to 0 cm3/ s in 20min, and the data changed as negative due to the decrease of slag oxidation and recovery of vanadium from slag to metal.

Jan 1, 2015

By J. G. Reid

Nickel is second only to aluminium, of all non-ferrous metals, in energy required to convert the ore to metal. Nickel Laterite ores, which constitute the feed source for approximately 40% of world nickel production, are at a particular disadvantage because of the absence of sulphur, as an energy source, in the ore and because lateritic ores general 1 y are not amenable to beneficiation. The dramatic escalation of oil prices which commenced in 1973 and continued for a decade meant that Nickel Laterite refineries using oil as a primary energy source were placed at a distinct disadvantage relative to refineries utilizing nickel sulphide concentrate feeds. By the late 1970's the continuing large difference in oil and coal prices caused Greenvale to consider converting certain high oil consuming areas of the refinery to coal. These investigations confirmed that the areas of ore drying and power generation, which together consumed 50% of total Plant oil requirements, could be economically converted from oil to coal firing. Construction of the coal conversion facilities commenced in October 1980 and the first ore drying air heater came on line in August 1981. Construction was completed with the commissioning of the coal fired boiler in June 1982. This paper outlines the additions required to receive and utilize coal in ore drying and power generation and how the changeover was completed with minimal process disruption.

Jan 1, 1988

By N. M. S. Balbinot, A. L. Rodríguez, C. M. Mahlmann, R. de C. de S. Schneider

The use of sunflower oil co-products it was studied for production thermoplastic composites. Thermoplastic composites have been processed in polyethylene matrices of virgin linear low density polyethylene (LLDP) or recycled. Samples have been formulated with 10% mass fraction of sunflower bran, seed coat and mixture of bran and seed coat. The material characterization has been achieved by mechanical tensile test and Shore D hardness and by density physical testing. The results have demonstrated better properties to thermoplastic composites with sunflower seed coat.

Jan 1, 2008

By Wiraseranee. Chompunoot, Kazuki Morita, Toru H. Okabe

"Aiming at the development of more effective recycling processes, dissolution behavior of rhodium into molten slag was investigated. Using a pure rhodium crucible and Na2O-SiO2 slag system, equilibration experiments were carried out for 18 h at 1423-1623 K under various oxygen partial pressures of 0.005-1 atm with varied slag basicity. Rhodium solubility increased with increasing oxygen potential, slag basicity, and temperature. Rhodium dissolved into slag as rhodate ion ([RhO2]-) by the endothermic reaction: Rh(s) + 3/4O2(g) + 1/2O2-(in slag) = [RhO2]-(in slag). In the dissolution reaction, the “rhodate capacity” of slag is newly-defined. The correlation between rhodate capacity and optical basicity is reported.IntroductionDue to its high chemical resistance and outstanding catalytic properties, rhodium (Rh), one of the platinum group metals (PGMs), is utilized in various applications such as catalysts, molten glass vessels and containers, and electronic devices. Owing to the rarity of Rh resources in nature, recycled Rh from scraps such as spent automobile catalytic converters is currently considered as an important source of Rh supply [1]. According to the recycling practices, Rh is currently mainly recovered from scraps along with other PGMs such as platinum (Pt) and palladium (Pd) by a dry process (e.g., smelting), a wet process (e.g., leaching and subsequent separation of PGMs from aqueous solution), or a combination of both processes [2]-[4]. Among these processes, smelting is commonly applied because PGMs can be effectively separated from a relatively large amount of various impurities coexisting in scraps. In the smelting process, Rh and other PGMs are collected in the collector metal (e.g., iron and copper), and impurities in scraps are removed into slag [4]-[6]. The process may be carried out at a temperature range of 1573-1973 K, in either an oxidizing or reducing atmosphere. Due to the high oxidation resistance at high temperatures, Rh is expected to be collected efficiently in the metal collector rather than being oxidized and forming RhOx in a molten slag. However, Rh loss into slag does occur in this process [7]."

Jan 1, 2011

By H. Y. Sohn

A novel solvent extraction process in which the emulsion is generated by bottom gas injection rather than mechanical stirring has been developed. This process has a number of advantages over the mixer-settler unit or the spray column in terms of simple equipment configuration and the ease of cleaning and process control while providing a large interfacial area for mass transfer. The equipment consists of a horizontal cylindrical vessel in which the two immiscible liquids flow countercurrently. High-strength gas jets are injected from the bottom at certain intervals along the length of the vessel. The gas jet creates a plume zone consisting of an emulsion of the two liquids which contains a large interfacial area for rapid mass transfer. The two liquids then disengage and flow in the opposite directions before entering another plume zone. Thus, the process combines the simplicity of a cylindrical vessel, having no moving parts, with the contacting efficiency of a mixer-settler. The gas can be recycled in a closed loop, thus eliminating mist and other emission problems. These advantages would be especially significant for treating large-volume/low-value liquid streams which contain hazardous substances and/or suspended solid particulates.

Jan 1, 1996

By C. Damiani

The Chuquicamata smelter, operating since 1952, has gone through several developing stages which have been characterized by the addition of peak technology for copper concentrate smelting (Teniente converter and Outokumpu flash furnace) with an intensive use of technical oxygen, which has permit-ted to partially discontinue the reverberatory furnace utilization. This paper shows the main indicators and operational practices at present, as well as those concerning maintenance aspects. Finally, the most relevant topics related to the future development of the smelter are mentioned with special remarks on the Decontamination Plan, which allows US to keep the high level of production, reducing the emission of contaminants according to the legal requirements in force.

Jan 1, 1993

By Rubén J. Sánchez Rodriguez, Carlos M. Fontes Vieira, Carlos E. Gomes Ribeiro

Ornamental compound stone are produced by industry for decades, however, few published studies describe these materials. Brazil has many deposits of stone wastes and a big potential to produce these materials. This work aims to evaluate the chemical resistance of ornamental compound stones produced with marble waste and unsaturated polyester. An adaptation of Annex H of ABNT NBR 13818:97 standard, with reagents commonly used in household products, was used. The results were compared with those obtained for natural stone used in composite production.

Jan 1, 2015

By T. Mutoh

Tellurium in raw slime has recently been recovered as copper telluride in Onahama Smelter & Refinery. The slime is decopperized with sulfuric acid solution in conventional leaching tanks. The pregnant leach solution containing 45 g/l of copper and 1 g/l of tellurium is introduced to a copper telluride recovering reactor. The tail solution from the reactor containing less than 20 mg/l of tellurium is recycled directly to circulation tanks of copper electrolysis. The impurities of the product copper telluride is kept below 1% without any purification.

Jan 1, 1990

By Moelans. N.

A method using an ex-situ electrochemical measurement device was developed to determine the oxygen potential of non-ferrous metallurgical slags. The electrochemical cell consists of the molten slag sample, an inert Ir electrode, a stabilized Zr02 solid electrolyte and a NilNiO reference electrode. Different slags from non-ferrous pyrometallurgical processes were analysed at I 100 and 1200 °C and pO2values between 10-3 and 10-12 bar were obtained. The measurements were evaluated with thermodynamic calculations and using processing considerations. It was found that the reproducibility and stability of the measurement was significantly improved by shielding the molten slag from the atmosphere by a thin layer of carbon, especially for slags with a low oxygen potential.

Jan 1, 2003

By Guolin Zheng, Jian Pan, Deqing Zhu, Xianlin Zhou

"In ferronickel production, nickel oxide and part of the iron oxide are reduced to metal by agglomeration and smelting in blast furnace. Due to the physical and chemical properties of the laterite ores, a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality. In this paper, the process of pelletization of nickel laterite was developed, and some parameters to strengthen the pelletization of nickel laterite have been optimized. The results show that the compressive strength of fired nickel laterite pellet can reach over 2000 Newton per pellet while firing at the temperature of 1220 °C~1250 °C in 12 min. The product pellet can be used as high-quality burden for blast furnace to manufacture ferronickel.IntroductionIn recent years, the global stainless steel market was developed exuberantly, which greatly promoted the needs of the basic raw material of stainless steel smelting - metal nickel. Currently nickel sulfide ores are only 40% of global nickel reserves, but offer 60% of all the nickel production. However, with the deficit of resources, the nickel sulfide ore (high grade ore) is depleting, so there is an increasing focus on the utilization of low-grade nickel laterite. Recent research has focused on the wet treatment process to utilize nickel laterite, and less on the use of other technologies [1-8]. The economical and efficient technology relies on the reduction of nickel oxide and part of the iron oxide metal by agglomeration and smelting in blast furnace in China. Some domestic steel companies have adopted this process [9, 10]. Unfortunately a large fraction of fines is generated during the pre-treatment stages and the strength of agglomeration is weakened, which results in low productivity and bad quality of fired pellets. In this study, the process of pelletization of nickel laterite was developed firstly, and some parameters to strengthen the pelletization of nickel laterite have been optimized, and the product pellet can be used to produce stainless steel and ferronickel alloy by blast furnace."

Jan 1, 2011

By Lev Levin, Sergei Lesokhin

"The formation of titanium carbide during hot filament assisted carburizing of NiTi alloy was investigated. Phase content and morphology of the diffusion zone were examined by X-ray diffraction, X-ray microanalysis, SEM, and Auger electron spectroscopy. The growth of stable and adherent TiC film was observed. A non-planarity of interphase boundary was noticed. The applicability of the chemical diffusion approach to the analysis of the experimentally observed interface instability is discussed. A criterion, taking into account the influence of growth stresses on the stability of the flat interface, is developed by means of linear perturbation analysis.Introduction.Equiatomic intermetallic NiTi belongs to a class of materials exhibiting the shape-memory effect. The unusual property of this compound promotes its application in many fields, from aerospace technologies to medicine. The relatively high ductility ofNiTi also permits its use as a matrix material in metal-ceramic composites. The objective of this work was to investigate the possible incorporation of a ceramic material (titanium carbide) into NiTi by gas carburizing.Free energy calculations indicate the potential to obtain TiC by carburizing Ni-Ti binary phases. The main obstacle to such a process is the high affinity of titanium to oxygen. At moderate temperatures the formation of TiC is preferable to titanium oxidation only if the partial pressure of oxygen is extremely low [1]. This problem was overcome in this work by the use of hot filament assisted gas carburizing. Due to chemical reactions occurring near the hot filament, the gas mixture, initially consisting of methane and molecular hydrogen, was enriched by atomic hydrogen [2], drastically decreasing the content of free oxygen in the carburizing atmosphere.The second part of this article concerns the theoretical analysis of reasons that lead to the development of the experimentally observed morphology of the diffusion zone. In particular, the influence of the growth stresses on the morphology of an interphase boundary is investigated."

Jan 1, 1996

By K. J. Martchek

"This introductory presentation will highlight recent efforts to quantify the positive value of recycling metals such as aluminum, magnesium, lead, zinc, nickel and copper in relation to the three pillars of ""sustainable development"" - environmental protection, economic development and improve social consequences.This presentation will provide an overview of life cycle assessment profiles increasingly being utilized by customers, regulators and environmental advocacy groups to holistically evaluate the environmental performance of materials and products. The environmental profiles of prodi.lcts containing recycled metal will be presented based on rules established by the International Organization for Standardization (ISO).Significant to the life cycle profile of metal products is recent confirmation. that recycling has the potential to reduce materials production energy consumption by 95% for aluminum, 80""/o for magnesium and lead, 75% for zinc, and 70% for copper. Furthermore, . ""metals are eminently and repeatedly recyclable, while maintaining all their properties (1 ). "" Their durability relative to many hydrocarbon based materials enhance .their life cycle performance. However, the persistence of metals when dispersed into our natural environmental makes recovery and recycling particularly important Overall, when considering life cycle effects, recycling is critical to a sustainable future for metal products.Finally, regional and international regulations will be highlighted which will effect the efficient recovery and recycle of metals and their overall contribution to environinental protection, economic development and the enhancement of society."

Jan 1, 2000

By Hideki Yamamoto

A new technology to convert fluoride gas (C2H2F4 ; R-134a) contained in the exhaust gases from semiconductor manufacturing plants and refrigerators directly into a harmless substance have been established, thus, presenting a new concept for the disposal of fluoride gases such as CFCs that are associated with the global warming. Experimental results verify that chemical reactions with metal compounds can take place at substantially lower temperatures of 700- 800K as compared with combustion. treatment temperatures of 1200-1500K. The reaction product is mainly metal fluoride, which chemically is a harmless material. Furthermore, this process is compact, easily controlled, safe and has low running costs. This paper deals with a new chemical reaction method for the harmless disposal of gases effecting the global warming.

Jan 1, 2003