Search Documents

By K. Lillkung, O. Forsen, J. Aromaa

"The dissolution rates of Pt, Pd and Rh in 250 g/L NaCl solution were calculated from the current densities determined by polarization curves and potentiostatic measurements measured with wire electrodes at atmospheric pressure. The results achieved with the two methods were similar. The dissolution rates at the corrosion potential were in the order of few nanometers per hour. The polarization curves indicated that to achieve dissolution rates required for economical operation on an industrial scale, the samples need to be polarized to higher potentials. When polarized to higher potentials, the metal dissolution rates were in the order of micrometers per hour. As the Tafel slopes of the metal dissolution region are fairly steep, the potential affects the dissolution rate greatly. Based on the activation energies, the dissolution reactions were controlled by a charge transfer step.IntroductionPlatinum group metals (PGM) have some very unique properties such as their inertness, giving excellent corrosion resistance, and a high melting point. At the same time, these factors make the refining of these metals very challenging. The main applications where PGMs are used are different catalytic converters, mostly in automotive catalysts. The used catalysts are also an attractive secondary source of PGMs. The exact concentrations of PGMs in catalysts vary widely depending on the manufacturer, the age and the capacity of the catalyst. The concentration of Pt in a new catalytic converter range from 300 to 1000 ìg/g, Pd from 200 to 800 ìg/g and Rh from 50 to 100 ìg/g [1]. Precious metal catalysts usually consist of a coat of the metal supported on ã- alumina. The recovery of metals from automotive catalysts has received much attention during the last few years [1-3]. In the near future, the use of PGMs in fuel cells is predicted to increase the amount of secondary PGMs available [4]."

Jan 1, 2012

By Gerhard Meyer

A new instrument for the determination of iron., zinc, calcium, and other metals independently directly in the fumes emitted from steelmaking processes is described. Based on the well- accepted method of X-ray fluorescence, the instrument can detect numerous metals simultaneously in the fume as well as report their concentration on a mass per unit time basis real time to a control room computer. The instrument mounts on the wall of the fume duct and can., via a small opening, directly view the hot exhaust plum inside the duct. The concentration of metal in the fume over time has been shown to change dramatically depending on process variables. Variables such as oxygen flow rate, lance height and nozzle configuration., slag condition., and episodic scrap addition can affect the presence of metal particles and fume in the exhaust. An analysis response time of 6 seconds enables better control of the steelmaking process thereby conserving primary resources and reducing environmental impact.

Jan 1, 2001

By Ullrich Kammer

Metaleurop's secondary lead smelter at Oker produces 60.000 mtpy of lead and lead alloys. More than 8O2 % of the raw materials are spent lead acid batteries. The other 2O2 % consists of drosses, ashes, scrap lead, type metal, sludges, etc., and is processed in a short rotary furnace (SRF). Also, industrial batteries not fitting in the battery scrap treatment plant are processed in the SRF provided with gas/oxygen-burner. Till Sept. 199O2, a soda ash slag was used in the SRF-smelting similar to the rotary kiln-smelting at Oker. Facing the future problems of handling and dumping soda ash slag, Harz-Metall GmbH has improved SRF-smelting with a non¬hazardous slag, insoluble in water, easy to dump and cheap in fluxes. This slag is based on a CaO-SiO2 -Fe0-type. Aim of the slag smelting is to be within the temperature range of 2 1100° and 1200°C - the eutectic line of Olivine in the corresponding ternary system. Since Sept. 199O2 Harz-Metall GmbH has operated the SRF with an "Olivine-type slag" with good results. Although the material is a "leady" slag. HMG is optimistic of using it as a filling material for construction purposes.

Jan 1, 1993

By Z. Yang

The flotation behavior of the. green algae Chlorella vulgaris and a wild Chlamydomonas spp. was studied in the presence of Zn(II) using dodecylammonium chloride as collector. At about pH 6. both organisms readily float as amine concentration approaches lx10-3 kmol/m3. In addition, electrokinetic measurements were made on the organisms as a function of pH in both the presence and absence of Zn(II). It was found that the Zn(II) has a considerably greater effect on the zeta potential of C. vulgaris than on Chlamydomonas. Zn(II) adsorption studies also indicated that C. vulgaris is able to accumulate more Zn from solution than the Chlamydomonas.

Jan 1, 1991

By Hoda Emami

In this study, a combined pyrometallurgical and hydrometallurgical technique has been designed and used to recover rare earth mixture elements (REE) and cobalt from a NdFeB magnetic waste. while addressing the cost of reagent and process facility. This process can be adjusted to different magnetic wastes regardless of their compositions. Prior to the leaching, the magnet scrap was pretreated by two rounds of roasting (750°C in air) and a mechanical grinding in between, to convert iron metal to ferric oxide. Subsequent leaching was performed using optimized conditions (pH, temperature and retention time) where the extraction ratio of REE to Fe III is the highest. After removing iron content from the leachate (pH ≈ 3), REE was precipitated selectively and purified further. The produced REE concentrate reaches 99% purity with 85% recovery in a single run. The cobalt oxide was isolated from the PLS as a by-product with 99.8% purity.

By J. B. Cocanour

Pioneering work at the U.S. Bureau of Mines (USBM) has produced a personal computer (PC)-based, software-driven video photometric color sensor for real time process control of metallurgical streams. The video photometer is an inexpensive optical sensor which operates in the visual area of the electromagnetic spectrum and collects color information through plastic optical fiber. The red, green, and blue (R/G/B) voltage components of the color video signal are digitized and characterized through software and then presented as the control variable for software-based proportional-integral-differential (PID) control. This sensor has been successfully employed in the control of a laboratory copper electrolytic circuit. With this sensor, copper solutions were analyzed on-line without the need for sample removal, dilution, mixing or reagent addition, thereby allowing for the real time control of the circuit.

Jan 1, 1994

By Steven E. Follin

In-situ leaching is commonly used to recover uranium from low-grade deposits in sandstone formations. Acceptable recovery rates can only be obtained if the formation retains its permeability during leaching. Field experiences indicate that microbial growth, stimulated by the leaching pro- cess, can cause plugging problems. To investigate this hypothesis, leach solution and solid samples from well casings and submersible pumps were obtained from four in-situ mining sites. Chemical and microbiological analyses were performed. Bacillus species, Micrococcus species, pseudomonads, and xanthomonads were isolated from these samples. A mixed culture of these organisms was inoculated into a uranium core that was being leached in the laboratory. The permeability of this ore sample decreased to one-third its original value after 16 days. The addition of hydrogen peroxide (0.2 g L-1) to the leach solution killed the microbes and restored the permeability to its original value. This suggests that periodic injection of hydrogen peroxide into production wells may reduce microbial plugging in these wells and the immediate surrounding formation.

Jan 1, 1985

By Bo Yan, Jiaquan Zhang, Haibo Sun

"Based on the validation of steady-state isothermal mathematical model by a 0.4-scale water model for the single-strand slab casting tundish, the effect of varying pouring temperature on the flow, temperature field, and residence time distribution(RTD) of the liquid steel was studied by a transient hydrodynamic model. Due to the decreasing temperature of ladle stream over a casting period of 50 min, the direction of vortex flow at the downstream side of dam changes to clockwise from the anticlockwise at 4 min after the new teeming, and reverts to anticlockwise direction again at 43 min. Meanwhile, the melt flow state in the dam hole is also varying with time. For conventional isothermal water modeling, the RTD parameters obtained are much different as compared with the non-isothermal ones. For the flow control devices(FCD) design, however, the identical optimal scheme can be concluded from the point of view of isothermal modeling.IntroductionOriginally, tundish was adopted as a buffer and distributor to hold and allocate molten steel for sequence casting upon ladle exchange and to provide a desired steel flow rate to the mould below. With the increasing demand to strand quality, the tundish has become a critical metallurgical reactor to enhance inclusions removal, avoid reoxidation of molten steel, and prevent slag entrapment. The general trends to obtain these metallurgical effects are to optimize steel flow pattern and to extend the residence time of molten steel in the tundish through increasing the volume of tundish and/or using FCDs in the interior of the tundish."

Jan 1, 2012

By V. M. Lsoitko

Statistical methods of technological mineralogy are used to model processing flowsheets in order to improve ore dressing efficiencies. The procedure involves determining geological and mineralogical characteristics of ores, classifying ore types and metallurgical procedures, and developing computer programs to interpret essential mineralogical parameters from on-stream analysis data. The on-stream analysis data include magnetism, radioactivity, luminescence and assays. The data are interpreted by computer and appropriate adjustments are made automatically in the plant.

Jan 1, 1989

By Jose Castro

The growing demand of scrap to supply the electric arc furnace has driven to search for new alternatives of raw material. The DRI produced using self-reducing pellets has become competitive due to the potential use of a wide range of carbonaceous materials such as coal, charcoal, biomass etc. In this context, the rotary kiln process using improved technologies such as post-combustion and self-reducing burden is a promising source of high quality raw materials. This paper presents a mathematical model of the rotary kiln process designed for self-reducing pellets and post-combustion. The model is based on the transport equation of two-phase flow, energy and mass transfer. The solid material is composed of a typical self-reducing pellet. The model considers the solid phase (C, volatiles, Fe2O3, Fe3O4, FeO, Fe, H2O, SiO2, Al2O3, MgO, P2O5, K2O, Na2O, FeS, CaO and gangue) and the gas phase (N2, O2, CO, CO2, H2, H2O, SO, SO2 and SiO). For each of the above components a conservation equation is solved and the mass and energy transport is accounted. The set of differential equations are coupled by the rate equations describing the kinetics of the several reactions, which take place within the rotary kiln. All the conservation equations are solved based on the finite volume method applied for a three-dimensional cylindrical coordinate system. Simulation results are presented for global parameters such as metallization degree, productivity, gas utilization ratio and calorific value. Inner conditions such as three-dimensional gas and solid temperature patter and compositions are discussed.

Jan 1, 2006

By Kejun Liu

Platinum and palladium are usually dissolved together and followed by separation. In this study, the selective leaching of platinum and palladium from a secondary resource, such as dental waste, by using chloride solution (hypochlorite and chlorate) has been developed. Results indicate that about 100% of palladium could be initially extracted by the combination of 0.3 mol/L sodium hypochlorite (NaClO) and 0.068 mol/L sodium chloride (NaCl) at pH 1.2 and 298K in 1.5 hours, or the combination of 0.005 mol/L sodium chlorate (NaClO3) and 6 mol/L hydrochloric acid (HCl) at 298K in 0.5 hour. About 100% of platinum could be extracted from the residue by the combination of 0.47 mol/L sodium chlorate (NaClO3) and 12 mol/L hydrochloric acid (HCl) at 298K in 2 hours.

Jan 1, 2003

By Fashina Olugbenga Emmanuel, Ghazali Akeem, Adegbola Adekunle Amos, Omotoyinbo Joseph Ajibade, Olaniran Oladayo

"Modern engineering materials are required to be light weight and corrosion resistant, coupled with high strength and hardness. In this work, Al formed the parent metal and alloyed with 2.03% of Copper by sand casting process. The cast product 2024 was warm worked at various temperatures ranging from 300 to 5600c at 5%, 10%, 15% and 20% deformation respectively and aged accordingly. The results showed that the mechanical properties vis-à-vis hardness, tensile improved with increasing % deformation at a higher temperature. This was due to the progressive close-up of the voids emanated from casting by increasing deformation which is evident from the micrographs. MATLAB was also adopted to generate a model capable of determining the trend of flow of stress at operating temperatures. This was of immense value due to an increasing impact at higher percentage deformation with temperatures. Hence, Al -alloys will find applications in land vehicles, ships, trains, and aircraft, at elevated temperature.INTRODUCTIONThe problem of safe vehicle design with maximum impact energy absorption is a significant subject in structural crash worthiness design [1]. All engineering designs are expected to ensure the safety of users' life. This informed several studies meant to probe the causes of component failures in equipment, vehicles, and aerospace design and decide on appropriate solutions through materials selection techniques. A common example is in the design of crankcases and heads, piston, and cylinder blocks. As with engine blocks, cylinder heads can be made of Cast Iron or Aluminium Alloy. A head made of Aluminium alloy is lighter in weight than if it were made of Cast iron [2]."

Jan 1, 2013

By Stephen R. Brown

Current conditions in the copper market demand that mine and plant operators make budgeted production targets at the lowest possible unit costs. For those companies bringing new production capacity on-line, achieving budgeted production levels as quickly as possible after start-up is vitally important to minimize unit costs and to begin a positive cash flow. Whether the objective is to simply improve unit costs or successfully start-up a new, complex plant, success will be strongly influenced by .the skill levels of the operators :and supervisors. The only way to assure return on plant investment, and to survive during depressed metal prices, is to ensure that plant operators have the knowledge to effectively run the plant. Technology available in computer-based, multimedia training systems, including: interactive animation, videos, voice-overs, schematics, and text can now be used to train operators at their own pace using plant-specific information. Additionally, it has been shown that learning through multimedia provides a higher degree of long term retention than more traditional learning methods.

Jan 1, 1999

By Zhenyang Wang, Yiran LIU, Xiangdong Xing, Jianliang Zhang, Zhengjian Liu

Basic characteristics of marine placer were systematically studied by chemical analyze, scanning electron microscope and X-ray diffraction in this paper. It could be found that the marine placer mainly consists of titanomagnetite and titanohematite. A series of experiments were performed to investigate reduction-magnetic separation for Fe and Ti from the marine placer. Effects of reduction temperature, reduction time, carbon ratio, magnetic density, and grinding fineness on the reduction-magnetic separation process were investigated. And the optimal process parameters were obtained as follows: the reduction temperature 1300, the reduction time 30 min, the carbon ratio 1.1, the magnetic density 50mT, and the grinding fineness of 0.074μm 86.34%. Under such conditions, the metallization rate, iron grade of magnetic substance and iron recovery reached to 94.23%, 97.19% and 90.28% respectively, and the titanium grade in non-magnetic substance and recovery of was 57.94% and 87.22% respectively. The effective separation of iron and titanium could be achieved in reduction-magnetic separation process.

Jan 1, 2015

By Shivendra Sinha

Total pressure oxidation (TPOX) is widely outreached leaching practice for base metals from sulfide minerals, wherein high temperature (T ∼ 200 °C) and oxygen pressure (pO2 ∼ 25 bar) are required. These aggressive conditions intensify the oxygen mass transfer, and therefore facilitate metal dissolution. However, challenging-cum-negative aspects of such practice are energy and material intensive requirements and high oxygen demand. Thus, the present study explores the novel emulsified medium for enhancement of oxygen mass transfer, which assists faster metal dissolution at significantly lower temperature and pressure condition. It is possible to achieve quantitative dissolution (>95%) of Cu, Ni and Co from mixed sulfide minerals at T ∼ 95 °C and pO2 ∼ 2 bar using an emulsion of 2.5% (v/v) n-Hexadecane in dilute sulfuric acid. In addition, n-Hexadecane was found to be inert, stable and immiscible in a pressurized leaching system, thus can be easily separated and recycled in subsequent leaching stages. Thus, this study offers an energy efficient route for low temperature-pressure leaching of sulfides.

By KAGAN BENZESIK, Onuralp Yücel, Mehmet Bugdaycı, Ahmet Turan

ZrB2 and B4C are one of the most significant advanced ceramics. They are being used in various industrial areas from space technology to nuclear industry owing to their physical properties such as high melting point, high thermal/electrical conductivity and low density. Present study was conducted in two main stages: Self-propagating high-temperature synthesis (SHS) reactions and leaching. ZrO2, Carbon black, B2O3 were used as starting material to produce ZrB2-B4C powders by SHS. Also Mg powder was used as the reductant. The reaction mixtures (approximately 100 g) were mixed thoroughly 15 minutes in a turbula mixer and charged into Cu crucible and compacted. W (tungsten) wire was placed at the top of copper crucible and the reaction realized by passing current through the wire. After initiation, a highly exothermic reaction became in a self-sustaining mode and propagated throughout the SHS mixture. The samples were characterized by using AAS and X-Ray Diffraction.

Jan 1, 2016

By Jian Li

Corrosion resistance of materials is highly dependent on the microstructure of the specific material. Apart from general corrosion rate measurement using techniques like linear polarization and A.C. impedance, microstructural investigations are frequently needed to identify the root cause of corrosion. Advanced techniques, including scanning electron microscopy (SEM) and transmission electron microscopy (TEM), have been well integrated into routine characterization studies. Other microscopy techniques, including electron probe micro-analyzer (EPMA), Auger, X-ray photon spectroscopy (XPS) and secondary ion mass spectroscopy (SIMS), can provide detailed chemistry information on corrosion products. In recent years, focused-ion beam (FIB) microscopes have evolved into an important microstructural characterization instrument. In this study, corrosion of rebar encased in concrete was studied in great detail using advanced microscopy techniques. Corrosion product on the rebar surface was identified as ferrous oxide with relatively large crystal size. The morphology of this passive layer was thoroughly analyzed, and its formation mechanism is proposed.

Jan 1, 2009

By G. Kugler, M. Tercelj

"The use of the up-to date light alloys and their development are in the sharp ascent especially in transportation industry. In the last years the use of the magnesium alloys for the various purposes was strongly increased. The aim of present research was to study the influence of solidification rate on hot workability and on obtained mechanical properties of AM60 magnesium alloy. The study was also focused on possibility to omit prior homogenisation process which would result in cost reduction. The solidification of gravity cast alloy has been investigated with various methods of the thermal analysis: in situ simple thermal analysis and simultaneous thermal analysis. In order to reveal optimal hot working conditions the deformation behaviour was studied in the temperature range 200-450°C and strain rates between 0.001-lOs-1. Mechanical properties have been studied with tensile and impact toughness testing.IntroductionIn recent years, the increased demand for magnesium alloys has been mainly driven by the need of automotive and transportation industry to reduce the weight, as this is the most important parameter to reduce the energy consumption. Beside their very low weight in comparison to other metals, the magnesium alloys are characterized by good machinability, corrosion resistance and good mechanical properties, and can thus compete with aluminium alloys and for some applications even with steels. Due their decreased workabilty they are typically used as cast alloys, but in recent years also the research of their wrought state has become more extensive [1-7]. Decreased hot workability of magnesium alloys originates from their hexagonal close-packed structure. One of the most popular magnesium alloys with great potential for many applications is AM60 (MgA16Mn), which is predominately used for casting. But its application could be increased if the mechanical properties, could be improved. This can be done by hot working. Namely it is well known that wrought microstructure is characterized by better mechanical properties in comparison to as-cast state. On the other hand due to its low hot workability the homogenization process is required prior hot deformation, which results in increased production costs. Thus the aim of the present research was to study the influence of solidification rate on hot workability of AM60 alloy in order to improve its mechanical properties and to check the possibility of producing near-net-shape casting products omitting homogenisation process by employing small additional deformations after casting. Within the framework of this research the solidification of gravity cast AM60 alloy has been investigated with various methods of the thermal analysis."

Jan 1, 2011

By Liyuan Chai

The corrosion mechanism of A3 steel induced by chloride ions in the purified water had been investigated with the A C Impedance technique. The results showed that there were another two factors which determined its electrochemical corrosive rate: the electrode potential and coverage ratio of chloride ions on the surface of A3 Steel. The corrosion mechanism of A3 steel in the solution with chloride ions emendation was two steps of electrode process with the rate-determining step of 0,32kFeClFeCle+--¾¾®++.

Jan 1, 2009

By Yongqi Sun, Zuotai Zhang

Our study investigated the influence of P2O5 and B2O3 on the viscosity and crystallization behavior of Ti-bearing blast furnace (Ti-BF) slags for the purpose of Ti extraction. The investigation of the crystallization behaviors were carried out using a single hot thermocouple technique (SHTT) and the viscosity was obtained by rotating cylinder method. For the viscosity, the results showed that P2O5 substantially increased the slag viscosity. P2O5 is a network-forming oxide, which increased the degree of polymerization of slags and accordingly increased the slag viscosity. However, both of slag viscosity and apparent activation energy for viscous flow remarkably decreased with B2O3 addition. As a typical network forming oxide, B2O3 was introduced into the network and existed dominantly as 2-D structure, BO3 triangular, which caused a simpler structure and a decreasing slag viscosity. As for the crystallization behaviors of Ti-BF slags, both P2O5 and B2O3 enhanced the crystallization trend of rod-shape rutile and suppressed the crystallization trend of dendrite CaTiO3. Therefore the added P2O5 and B2O3 caused the primary phase change from CaTiO3 to rutile. Additionally, it was found that the rod-shape rutile showed a 1-D growth, whereas the dendrite CaTiO3 showed a 3-D growth style.

Jan 1, 2015