Search Documents

By F. T. Principe

In order for solvent extraction technology to be acceptable as an alternative to existing jarosite precipitation circuits, iron must be cleanly separated and concentrated into a feed stream suitable for downstream iron by-product recovery which meets market specifications and economics. Ten years ago, significant progress was made in a joint McCill University/CANMET project that involved iron extraction with mono(2-ethylhexyl) phosphoric acid and stripping with HCI. Our iron solvent extraction research was reactivated recently by looking into this and other members of the organophosphorus extractant family. Our research focuses on the mechanisms and control of anion (SO42/CI) transport across the various phases (Rafinate/Organic/Strip), iron build-up in the strip liquor, and extractant stability/selectivity. In this paper, these issues along with some other performance parameters are discussed using data derived from an extensive search of the two commercially available and best known members of the organophosphorus family, di-2-ethylhexyl (D2EHPA) and mono-2-ethylhexyl (M2EHPA) phosphoric acid. Further in this discussion, the challenges lying ahead in the development of sx systems that overcome the deficiencies of D2EHPA and M2EHPA are outlined. In particular, the necessity of considering secondary separation technologies that can further concentrate iron values in the chloride strip liquor to levels economically attractive for the production of saleable iron oxide by pyrohydrolysis is addressed.

Jan 1, 1998

By Adelana Adetunji

Ilmenite ore samples obtained from Dankoli in Zamfara, North Western Nigeria has been characterized using Energy Dispersive X-ray fluorescence (EDXRF) technique, X-ray diffraction (XRD) technique and the Neutron Activation Analysis (NAA) technique. The major constituents in the ore were quantitatively found to be TiO2 and Fe2O3 in concentrations of about 60wt% and 31wt% respectively. These occur in the forms of magnesian ilmenite (Fe, Mg)(Ti, Fe)O3, pure ilmenite (FeTiO3), and barium copper yttrium oxide (Ba2Cu3YO6.56) minerals. Other constituents/impurities in minor or trace quantities include MnO, Ta2O5, Nb2O5, Wo, SnO2, Hf, Zn, V, Zr, Co, Pb, Br, Al, Rb, Y, Th and U.

Jan 1, 2006

By Zeng Zheng, Liu Chen, Yu Xing-Fu, Tian Su-Gui, Zhang Chao

"Single crystal nickel-base superalloy is prepared by using the various withdrawing rates. By measuring creep properties and microstructure observation, the influence of the element segregation on creep properties of the superalloys is investigated. Results show that the dendrite spacing and the segregation extent of the elements decrease with the enhancing withdrawing rate. The superalloy with smaller dendrite spacing has lower segregation of the elements and better creep resistance. The dislocations climbing over the rafted y’ phase is thought to be the deformation mechanism of the alloy during steady state creep. In the later stage of creep, the fact that some dislocations shear into the rafted y’ phase may twist the rafted y’ phase. As the creep goes on, the initiation and propagation of the cracks occur up to occurring creep fracture, which is thought to be the fracture mechanism of the superalloy during creep.1. IntroductionSingle crystal nickel-based superalloys consist of high volume fraction of ?? strengthening phase and ? matrix, and possess the excellent high-temperature mechanical and creep properties, therefore, they have become the main material to make the blades of the advanced aeroengines[1-3]. Some literatures report that the temperature-bearing and creep-resistance properties of the single crystal nickel-based superalloys can be remarkably improved as the increases content of the refractory elements, such as W and Re[4-6]."

Jan 1, 2012

By Aliye Arabaci

In the present investigation, an attempt has been made to study the reduction behavior of composite pellets consisting two different types of iron oxide fines (high and low grade) and coke or lignite fines as reducing agents. The reduction experiments were carried out under isothermal conditions and constant flow of nitrogen gas in the temperature range of 900 ? 1100 oC. The variables investigated are the reduction temperature, Cfix/Fe3O4 ratio, reduction time and reductant type. In the experiments carried out with Sivas Divrigi A head magnetite ores (high grade) at a temperature of 1100 oC, for 40 minutes and on the condition that Cfix/Fe3O4 ratio is 0.2, in which lignite and coke fines were used as reductant, degree of reduction was obtained as 91 % and 86 %, respectively. Whereas, in the experiments realized with Malatya-Hekimhan-Hasançelebi magnetite ores (low grade) on the same conditions by using lignite as the reductant, around 60 % degree of reduction was found.

Jan 1, 2008

By Xiao Y. Yan

A fused salt electrochemical process was investigated for the synthesis of non-oxide ceramic powders directly from metal oxides, boric oxide, and carbon powders by electro-deoxidation. Sintered pellets of the mixed powders were designed to act as a composite cathode in the electrolytic cell. Electrolysis was carried out in molten CaCl2-NaCl eutectic at 3.1 V and at 600-900 ºC under argon. The favoured cathodic reaction was the removal of the oxygen from the oxides to produce metal atoms that reacted with either the reduced boron atoms, forming a metal boride, or the carbon initially present in the sintered pellets to produce a metal carbide. The technical viability of the process was demonstrated by the electro-deoxidation of sintered pellets of TiO2/B2O3 and TiO2/C to produce TiB2 and TiC, respectively. Compared to existing carbothermic reduction process, this new electrochemical process may be less energy intensive and may lead to lower production costs. I

Jan 1, 2008

By A. F. Saavedra, N. E. Richards, C. J. McMinn

"The aluminum industry in general and Reynolds Metals Company in particular have continued to support development work for improvement of the Hall cell design and for alternative processes for the reduction of alumina. The evolution of the Hall cell design will continue into the next century as a result of further development of mathematical models, sophisticated control systems and new materials for cell components. This paper discusses the areas in which the new generation cell advances will differ from the present day design. Additionally, Reynolds Metal s has supported work for the development of a carbo thermic process to reduce alumina. Theoretical work has indicated that this process could possibly have economic advantage over the Hall process. Several complicated furnace configurations have been proposed to provide the conditions for successfully reducing alumina. The results of small pilot scale operation and most promising furnace design are discussed. For comparison, projected capital investment costs and operation costs are discussed. IntroductionThe evolution of the Hall-Heroult process will continue into the next century. This evolution will be influenced by economics, more .restrictive environment and worker protection requirements, and technological development. These factors will also cause changes in the competitive position of alternate processes for aluminum production.Several aluminum producers have made major investments in alternate processes for aluminum production in the past three decades and there is continued support in some companies for improvements in the Hall-Heroult process and for alternate processes. The more visible development work in reduction technology, not aimed at significant process changes, is in the areas of higher amperage cells with bus bar designs to reduce harmful magnetic effects, more advanced and automated feed, voltage and electrolyte composition control, improved energy efficiency and sol id waste disposal . Efforts to bring significant change to the reduction process are being made in development of materials that can function as inert anodes and cathodes. These materials could lead to the development of reduction cells with multiple bipolar electrodes operating on oxide feed and fluoride electrolytes. Development work on new processes was reduced in the last decade by several companies because of economic and technological realities. Reynolds Metals supported work on a carbothermic process to reduce alumina and produce commercial pure aluminum. This work progressed through small pilot plant operation, and resulted in development of furnace designs and operation regimes. This paper reviews how this and other technologies could influence the reduction of alumina beyond the year 2000."

Jan 1, 1988

By Peter Bauer, Klaus Gamweger

"Gas purging systems are well established in nonferrous metallurgy at multiple steps during metal production, including melting, converting, alloying, and metal cleaning. Since the kinetics of all of these stages are positively influenced by using gas purging systems the overall process benefits are substantial. In the aluminum industry, inert or reaction gases are blown into the melt using porous plugs to achieve improved metal grades, higher productivity, and more efficient energy utilization. To enable the most effective application of the process gases a complete package, termed AL KIN, was developed by RHI that includes porous plugs, refractory expertise, gas supply technology, and gas control equipment. This paper discusses the technological and economic advantages of this system and the specific benefits of fuel reduction, production time savings, decreased process gas consumption, and improved refractory service life and maintenance are illustrated using an aluminum slug plant in Austria.IntroductionIn addition to high quality production, increasing productivity is the main goal in many aluminum cast houses to maintain or even strengthen their market position. The Neuman Aluminium Group, based in Austria, North America, and based in Austria, North America, and China, is the largest slugproducer for tubes, cans, and automotive parts worldwide. Recently, a comprehensive improvement program was initiated at the Neuman Aluminium Austria slug plant in Marktl - the main factory and technological centre of the group. The principal goal of the optimization project was to increase the productivity of the strip-casting production. The investment included a gas purging system, ingot preheating equipment, a new insulated launder system, and optimized melting cycles. However, the introduction of the gas purging system was pivotal to the project and has accounted for approximately 50% of the benefits achieved. This paper describes the AL KIN gas purging technology and details the process benefits resulting from the improvements at Neuman Aluminium Austria."

Jan 1, 2009

By N. M. Komkov

The main operation of obtaining zinc from sulfide raw materials by hydrometallurgical technologies is the oxidation roasting of zinc concentrates in fluidized bed furnaces. The technical-economic parameters are determined by the parameters of the roasting process, which depend on the composition of the initial raw materials, the temperature of the bed and on other factors. The predetermined roasting temperature is maintained due to the change of specific efficiency as well as to the quantity of the heat removed from the bed. The efficiency of caissons depends at a high degree on the composition and the thickness of the accretion formed on the surface of the caissons. Forecasting the roasting results is impossible unless we know the mechanism of the accretion formation. The aim of the present paper is the thermodynamic analyses of the behavior of the charge compositions under roasting and the determination of the potential mechanism of the accretion formation. The thermodynamic analyses show that under conditions of the oxidation roasting the thermodynamic probability of the formation of zinc sulfate is higher than the probability of the oxide formation until a temperature of873 OK is reached. The thermodynamic probability of the formation of the lead sulfate is higher than the probability of oxide formation in the entire temperature range of roasting. The probability of formation of ferrites and silicates of zinc decreases only insignificantly the sulfate stability. The results of the investigation of the accretions composItion formed under roasting of concentrates with particle sizes less than 0.02 J..lm (60%), containing 65% of sphalerite (ZnS), 12% of pyrite and chalcopyrite (FeS2 and CufeSz) each, 3% of galenite (PbS), 7% of silica and other non-ore minerals, have shown that the composition of accretion varies depending on the depth of the accretion layer. The accretions on the caissons and the thermo-siphons consist mostly of zinc sulfate (more than 50%). The accretions of forehamber consist mostly of zinc oxide. They also contain ferrites and silicates. The formation of the sulfate zinc accretion in the cold parts of the fluidized bed furnace (the caissons and thermo-siphons) may be explained by a lower temperature on the surface and probably by a catalytic influence of the present oxides in the formation of S02 and sulfates. The nature of the structure of the accretion in the hotter parts of the furnace may supposedly be explained by the formation of elemental vaporous zinc during roasting.

Jan 1, 2003

By K. Murayama, M. Kawakami, T. Takenaka, S. Yokoyama

"Cokes play an important role of spacer in blast furnace. However, they degenerate during Boudouard reaction. Blast furnace cokes are reacted with pure C02 at I 072 to 1673 K. Reaction rate was obtained by the weight change of spherical specimen. The specimen after reaction was examined by microscopic observation. The reaction rate increased with temperature and was expressed by two Arrhenius type lines. The activation energy was 126 KJ/mol at higher temperature than 13 73 K and 202 KJ/mol at lower temperature range. At the higher temperature range, the reaction proceeded from the surface leaving unreacted core, whereas homogeneously whole inside at lower temperature. The porosity increased from the center to surface at higher temperature, whereas it was almost constant at lower temperature.IntroductionThe cokes have the function of fuel, reductant and spacer to keep gas and liquid flow in the blast furnace. Thus, the reaction mechanism of coke with several gas and the strength after the reaction should be important factor to control the blast furnace operation. The reaction mechanism of coke with C02 has been studied extensively. The rate equations were derived by Gadsby[ I], Ergun[2] and Turkdogan and Vinters[3]. They were compared and discussed by Kobayashi and Omori [ 4]. Effect of crystallization degree on the reaction rate was examined by Kashiwaya and Ishii[5]. Catalytic enhancement effect of ash componets have been clarified by Kashiwaya et. al. [6]. Although degradation of coke in blast furnace has been examined recently[7], however, the degradation of coke after the reaction with C02 has not been well clarified yet. In the present work, the metallurgical coke specimen was heated in N2 and C02 and the reaction mechanism and degradation behavior after the reaction was investigated."

Jan 1, 2000

By Jinrong (Patrick) Mang

Three of the most challenging problems in phosphate beneficiation are discussed: flotation efficiency, resource conservation and environmental impact. Some new flotation machines offer the opportunity of reducing power and reagent consumption significantly, while increasing specific capacity many fold. Efficiency might also be improved dramatically by replacing the "double float" process with a single-collector scheme. Model based software control is a powerful tool for improving overall plant efficiency. Recovery of phosphate values from the phosphatic clays could extend phosphorus reserve life significantly. phosphate recovery from the slimes might be achieved by sizing-flotation, selective flocculation and bioleaching. Reducing the volume of phosphatic clays produced is another key stop to minimizing phoephate logs. Such a reduction may be realized by floating at finer cut size. Although an ideal' dolomite separation process is yet to be developed, a cationic flotation process may prove to 'be economically feasible. Loss of phosphate in the desliming stage is the major problem with most of the flotation schemes for removing dolomite.

Jan 1, 1995

By Luiz A. Teixeira

A process is described whereby worn, deffective or crystallized photoconductive Se-As layers can be stripped off from aluminium photocopier drums, using hydrogen peroxide solutions in conditions such that the aluminium substrate is preserved from chemical attack. The process allows the stripped drum to be recoated with a new photoconductive layer, and to be put again in use.

Jan 1, 1990

By G. Taylor, S. Bounds, G. Moran, M. Cross, K. Pericleous

"A variety of interacting complex phenomena takes place during the casting of metallic components. Here molten metal is poured into a mould cavity where it flows, cools, solidifies and then deforms in its solid state. As the metal cools, thermal gradients will promote thermal convection which will redistribute the heat around the component (usually from feeders or risers) towards the solidification front and mushy zone. Also, as the evolving solid regions of the cast component deform they will form gap at the cast-mould interface. This gap may change the rate of solidification in certain parts the casting, hence affecting the manner in which the cast component solidifies. Interaction between a cast component and its surrounding mould will also govern stress magnitudes in both the cast and mould - these may lead to defects such as cracks.This paper presents a multiphysics modelling approach to this complex process. Emphasis will be placed on the interacting phenomena taking place during the process and the modelling strategy used. Comparisons with plant data are also be given."

Jan 1, 1999

By M. J. Adam

The U.S. Bureau of Mines is investigating the partitioning of selected complex minerals into simple phases using sulfidation reactions. Successful partitioning of complex mineralogy to simple phases may afford an opportunity to improve selective extraction of mineral constituents of economic value. The research has shown that complex minerals, such as chalcopyrite (CuFeS2) and pentlandite [(Fe,Ni)9Se]' may be partitioned to the simpler phases covellite (CuS) plus pyrite (FeS2) and vaesite (NiS2) plus pyrite (FeS2), respectively. Demonstrations of these reactions were verified through long-react ion-time (24 h or more) experiments, but basic rate investigations and modeling were not included in the previous research. This report describes research aimed at determining the rate at which the complex mineral CuFeS2 converts to the simple sulfides CuS plus FeS2. Small samples of CuFeS2 were blended with elemental S prior to thermal treating under an He atmosphere for time periods up to 4 h. Products from each treatment period were characterized using metallography, chemical analysis, X-ray diffraction (XRD), and scanning electron microscopy (SEM). Results of the investigation revealed a rapid conversion of CuFeS2 to CuS plus FeS2 early in thermal treatment periods. As the reaction occurred, a CuS rimming of particles was observed which separated the reacting species (CuFeS2 and S) and caused a considerable decrease in transformation rate.

Jan 1, 1991

By Joseph Hamuyuni, Pekka Taskinen

We present experimental results for the liquidus in the system Cu2O - CaO -Al2O3 at 1250 oC. In this study, we quantified the liquidus by the equilibration/quench/analysis technique, with Cu2O, Al2O3, and CaO as primary materials exclusively. Experiments were conducted in air at an at oxygen pressure (p) = 21.3 kPa). Equilibrated specimens were quenched in brine solution of 10 wt% NaCl. We then quantified the liquid chemical compositions by means of Energy-Dispersive X-Ray Spectroscopy (EDS) and Electron probe micro-analyzer (EPMA). This study reveals inconsistences in liquidus surface of the present ternary diagram of the system here in mentioned. Differences of up to 10 wt % compositions of the species have been observed.

Jan 1, 2015

By Zhang Chuanfu, Tan Pengfu

"A thermodynamic model is developed to simulate nickel flash smelting process. In the nickel flash furnace, oxidation of concentrate occurs at one end, and reduction of slag occurs at the other. The model makes use two zones, namely the reaction shaft/settler zone and the appendage zone and accounts for 6 phases (matte, slag, silica, magnetite, Cu-Ni alloy and gaseous phase), 13 elements (Ni, Co, Cu, Fe, S, 0, N, C, H, Si, Al, Mg and Ca) and 33 chemical components in nickel flash smelting system. The compositions of matte, slag and gaseous phases in equilibrium are calculated by using the data of free energies of formation and activity coefficients of components. Two nickel sulfide species are used to allow for the modeling of sulfur-deficient mattes. The model predictions are compared with the known industrail data from Kalgoorlie Nickel Smelter, and excellent agreement is obtained. The model can be a very useful tool for monitoring and optimizing the actual industrial operations of nickel smelting process. The distribution behaviors of Ni, Co, Cu, Fe, S and 0 in the nickel smelting furnace depend on the process parameters such as smelting temperature, volumes of air, the content of the elements~ charge and oil.1. IntroductionThe nickel flash smelting furnace essentially consists of a reaction shaft where nickel sulfide concentrate is partially oxidized with air, a settle zone where matte and slag are allowed to separate, and a slag cleaning end where coke is added to provide for the reduction of the oxidized nickel from slag, and electrodes are used to provide heat.The theoretical model to consider a mass balance for copper flash furnace is developed by S. Goto and R. Shimpo[1][2J. However, this can not be true for nickel flash furnace as a whole since oxidation of concentrate occurs at one end (in the reaction shaft/settler), and reduction of slag occurs at the other (in the appendage). Despite these limitations, an acceptable pseudo-thermodynamic description of the furnace can be achieved using essentially two zones, namely the reaction shaft/settler zone and the appendage zone. Compositions of gas, slag and matte in two zones are calculated."

Jan 1, 1998

By David Cocke

Study of surface and subsurface interfacial chemistry of metallic and similar systems has its enormous technological importance. Copper, for example, is a common component of many alloys and bulk amorphous systems. It is being increasingly studied today because of its use for electronic interconnect systems where processing is done below 200 ºC. Since several types of copper oxides exist, and the degree of their formation is dependent on temperature, perhaps characterization by EDS-SEM depth profiling and EIS might delineate one type of oxide from another. In this paper, we described our work on transformation of copper oxides with temperature ranging from 70 to 350 °C and their characterization by SEM, EDS, and XRD. We also showed the use of the phase angle portion of the impedance as a means to identify the predominant structure and the transition through Cu3O2 between the predominant stable CuO and Cu2O.

Jan 1, 2009

By Ahmad-Bitar¸ Riyad N., Shadia J. Ikhmayies

"CdSi-xTex thin films with O<x<0.3 were prepared on glass substrates by the annealing of CdS:In thin films produced by the spray pyrolysis technique. The annealing was performed in nitrogen atmosphere at 400 --,C in the presence of Te vapor. The compositions of the films were determined by energy dispersive X-ray detection (EDAX) measurements. Scanning electron microscopy (SEM) was used to investigate the morphology of the films. The transmittance of the films was measured at room temperature in the wavelength range 400-1100 nm and used to produce the absorbance of the films. The first derivative of the absorbance was used to estimate the optical bandgap energy Eg by using the minima in the first derivative. The relation between the bandgap energy and the fraction x was found to fit with a parabola and bandgaps in the range 2.196: =Eg: =2.480 e V were obtained. Urbach tailing in the bandgap was also investigated.IntroductionPolycrystalline thin film CdS/CdTe solar cells are promising candidates for low cost and high efficiency photovoltaic applications. The fabrication process of these cells involves the deposition of a p-type CdTe absorber layer on top of an n-type CdS one which acts as a window. The efficiency of the solar cell is affected by the method of preparation of both layers [1, 2].Interdiffusion processes taking place at the CdS/CdTe interface have largely been realized to significantly affect the device performance [3] by changing the bandgap of both CdTe and CdS which modifies the spectral response of the solar cell [ 4]. The formation of a mixed crystal or a graded layer causes a reduction in the lattice mismatch at the CdS/CdTe junction [5] which is about 9% [ 6] and then a reduction in the number of interfacial states and recombination centers, thus enhancing the solar cell performance [7, 8]. A complete understanding of the properties of the intermixed layers CdSxTe1-x that usually constitutes the interfacial region in the CdS/CdTe solar cell is essential. According to our knowledge, a lot of research was devoted to the investigation of the diffusion of S into CdTe [3-5, 9]; but little on the direct investigation of the diffusion of Te into CdS [6]."

Jan 1, 2011

By Renxing Li, Yongyong Gong, Yufeng Cheng, Zhenxing Yin, Xin Cao, Qijie Zhai

"This paper investigated the refinement effect of pulse magneto-oscillation (PMO) on the solidification structures of medium carbon steel S45C in metal mould. The induction coil was positioned at the middle of ingot. The results showed that solidification structure of the treated ingots was remarkably modified with a transformation from well-developed dendritic structures to small dendritic structures or globular structures compared to the untreated ingot. The area fraction of modified microstructure regions reached more than 80 percent. A further experimental investigation had been done to understand the influence of refinement effect on the solidification structure under different mould size. Theoretical analysis demonstrated that the mechanism for the refinement of solidification structure was that PMO promoted nucleation near the mould walls and changed the interface temperature gradient and concentration gradient in liquid, eventually leading to a transition from the columnar crystals to the equiaxed crystals.IntroductionIn recent two decades, the electromagnetic processing of materials (EPM) has been widely used in many fields such as ironmaking, steelmaking, and solidification processing [1-6], where EPM can control melt flow, modify melt shape, reduce macro-segregation and refine microstructure. Pulse magneto-oscillation [7-9] (PMO), as a novel technique of EPM, has a remarkable effect on grain refinement and high potentiality to be used in industrial production. Compared with ultrasound refinement technique, PMO can be easily employed to metal solidification processing for long time in no contact with hot metal liquid by using a water-cooled coil. Another important advantage is that PMO needs smaller energy compared to pulsed magnetic field which needs a very high current to obtain a strong magnetic field to get a satisfactory effect. These advantages mentioned above are beneficial for industrial application, which make it potential to be widely used in future. Gong et al. [7] have studied the refinement effect of PMO on pure aluminum and find that PMO can significantly modify the solidification structure of pure aluminum. Li et al. [9] have reported the effect of temperature field on solidification structure under the influence of PMO. On the basis of these works, this paper has studied the effect of PMO on solidification process of medium carbon steel S45C in a metal mould, which can also provide some information for industrial application of this new technique."

Jan 1, 2012

By Mototsugu Matsuno

A new process has been developed to treat fly ash generated from municipal incinerators, which contains not only toxic metals such as lead and cadmium, but also dioxins. The process includes the following steps; fly ash is formed into green pellets with some additives and the pellets are then roasted to eliminate or stabilize the toxic metals and to decompose dioxins. A pilot plant with a capacity of approximately 100 kg/hr was used to test the process, The tests verified that heavy metals were either volatilized or stabilized and dioxins were decomposed by high-temperature roasting. The pelletized ash was found to be non-toxic, so that it can be recycled as artificial lightweight aggregate. It was also found that volatilized metals collected as secondary ash can be recycled as smelting resources.

Jan 1, 2003

By Rainer Schmid-Fetzer

"Isothermal solidification can be used to form strong bonds at low temperature which remain solid at much higher temperatures. The exploitation of this principally known technique for new high temperature processing steps and applications in electronic assemblies is the aim of this study. Three basically different variants of this bonding process are given. A comprehensive metallurgical screening is performed and the feasibility of binary material systems is given on a quantitative scale. Very attractive systems are spotted that have never been studied before. Detailed examples for the realization of bonding with complex ternary and multilayer systems are given. A highly innovative example is the chip stack or wafer to wafer bonding of unmetallized Si or SiC at 250°C. The proposed bond remains stable above the melting point of Si and enables entirely new semiconductor manufacturing steps. An improved die bonding process was proposed and verified experimentally.1. IntroductionIsothermal solidification can be applied to form strong bonds at relatively low temperature which remain solid at higher temperatures. The general principle of this type of joining processes is illustrated in Fig. 1. An interlayer of a low melting component, Lo, is provided as a foil or a thin film coating between the high melting joint components, Hi. The assembly is heated under moderate pressure to the bonding temperature, T 8 , and a liquid filler forms, either because the melting point of Lo is exceeded or due to a eutectic reaction between Lo and Hi. This molten filler initiates a rapid interdiffusion or reaction diffusion between Lo and Hi and the subsequent approach to an equilibrium state results in isothermal solidification. The solid phases formed at T 8 in the joint region exhibit a remelt temperature above T8 •"

Jan 1, 1996