Search Documents

By Lloyd R. Nelson

Experimental results of three-phase mixing in a physical model of a CCRL for metals refining are presented. The system was operated above a critical lower liquid height-to- width ratio (H,/W) of unity, with adequate bottom gas injection through a line of central, single tuyeres (Q,/A = 7.5 cm/min, or c = 17 W/m3) to sustain levels of interphase transport considered appropriate to an industrial pyrometallurgical refining operation. The application of a thermal tracer technique to elucidate both longitudinal mixing and interphase heat transfer is discussed. The results indicate that even under conditions of significant bottom gas injection, it should be possible to maintain acceptably low longitudinal mixing 1 (D, < 20 cm /s and D,/uL < 0.1) in the CCRL. Interphase mass transfer coefficients of the order of 0.004 cm/s are predicted from the measured interphase heat transfer coefficients (h = 1.3 to 2.0 kW/m2K), using the heat and mass transfer analogy. Adequate rates of rehning are predicted for an industrial CCRL operated under such conditions.

Jan 1, 1995

By Ian M. Ritchie

Cementation or metal displacement reactions such as Cu2+ + Fe Cu + Fe2+ are among the oldest known hydrometallurgical reactions. They are still used in the recovery of some metals and in the purification of process liquors and waste water streams. However, they are often more complex than the stoichiometric reaction would suggest because they involve the simultaneous deposition of one metal onto a second which is dissolving. For example, sometimes a cementation will not take place, even though it is thermodynamically favoured. On other occasions, a cementation reaction will start but come to a halt as the depositing metal blankets the reacting surface. On yet other occasions, side reactions, catalyzed by the deposit, can be important. In this paper, the electrochemical basis of cementation reactions is described. The conditions for each of the complications encountered in these reactions are described and illustrated by examples drawn from a number of hydrometallurgical processes. The cementation reaction between activated carbon and gold thiosulfate is also briefly described, this reaction being unusual in that no dissolution of the carbon occurs.

Jan 1, 2003

By M. Wu, A. Kharicha, A. Ludwig

"The droplet formation during melting of a 400 mm diameter electrode is simulated with a multiphase-MHD approach. The computational model includes a layer of slag and a layer of liquid steel. A VOF approach is used for the interface tracking and a potential formulation is used for the electric and the magnetic field. The Lorentz force and the Joule heating are recalculated at each time step in function of the phase distribution. The first results provided by this model are presented.IntroductionThe Electro-Slag-Remelting (ESR) process is an advanced technology for the production of components of e.g. high quality steels [ 1-9]. An alternating current (Figure 1) is passed from a conventionally melted and cast solid electrode through a layer of molten slag to the baseplate. Because of the electrical resistivity of the slag, Joule heating is generated and the slag transfers this energy to ingot and mould surfaces and to the melting electrode tip. The molten metal produced in the form of droplets passes through the slag and feeds a liquid pool from where directional solidification takes place. The slag and the ingot are contained in a water cooled copper mould. As also the baseplate is water cooled, a heat flow regime is imposed that gives controlled solidification, and this results in improved structure characteristics of ESR ingots.This process involves two liquids, a liquid metal and a liquid slag. Each liquid is subject to a phase change due to melting and/or solidification. From a fluid dynamic point of view, the ESR process is clearly a multiphase process, with free interfaces (slag/pool, gas/slag), and with a mixed area (slag and falling steel droplets) [ 10-15].Physically, the development of the heat and mass transfer at the slag/droplet interface is important for the final ingot quality, composition and cleanliness. Visual observations of the droplet formation just under the electrode being melted is almost impossible. Due to the presence of high temperatures, opacity of the materials, and the presence of the mould it is not possible to directly observe the behaviour the slag/pool interface. Although usually assumed flat [1-9], a previous work [10] using a Volume of fluid (VOF) model has shown that the interface shape between a layer of slag and steel layer in a cylindrical cavity is highly coupled with the distribution of the electric current. A full scale simulation of the ESR process using a VOF model has shown that the shape of the pool interface is likely to be non flat."

Jan 1, 2011

By I. Gaballah

Spent hydrorefining catalysts may contain 4 to 6 % of COO and/or NiO, 8 to 16 % of Moo3 and up to 10 % V205 generally supported by alumina. Raw samples are roasted in order to eliminate carbon, sulfur and hydrocarbons contained in the spent catalysts. The roasting optimum temperature and time are 500 "C and 7 hours. Selective chlorination of roasted samples with Cl2 + air, Cl2 + N2 and Cl2 + CO is investigated in order to recover the valuable metals. Depending on the chlorination it is possible to recover more than 80 % of the Ni and Co about 95 % of the Mo and up to 80 % of vanadium compounds. Cobalt and nickel chlorides are obtained by leaching the chlorination residues&apos; by acidified water. Molybdenum and vanadium chlorides and/or oxychlorides are obtained by selective condensation from the vapor phase. The chlorination of the catalyst support, Al2O3, can be limited to less than about 5 %. Besides the reaction temperature and time, the oxygen partial pressure of the chlorinating gas mixture appears to be the key factor for the reactions&apos; selectivity.

Jan 1, 1993

By C. E. M. Meskers, U. Boin

"The increasing use of coated magnesium in consumer products results in creation of coated Mg scrap during product manufacture and after End-of-Life product treatment. Currently this material is generally not recycled, leaving a material resource unused. Closure of the magnesium cycle in a sustainable manner is necessary. In order to do so, the effect of coatings on the recycling process has to be quantified, predicted and minimized. For this purpose metrics have been developed, based on first principles supported by detailed understanding of the recycling process. The developed 3D metric enables quantitative assessment of the recyclability and links coating design, product design and recycling to each other in a visual manner. The parameters that form the metric can be measured and predicted, hence an engineering basis for Design for Sustainability of coated magnesium is provided.IntroductionEvery product progresses through the four phases of the product life cycle depicted by figure 1. In each phase residues are created. Their amount and composition is largely determined by the complex material combinations created/invented during product design in the manufacture phase. Compared to the ideal cycle the magnesium cycle is far from closed (fig. 2). Most noticeable is absence of the link between the EoL phase and raw materials production. A closed cycle only exists for class 1 scrap, which goes from the product manufacture phase directly to production from industrial material and returns to the manufacture phase as magnesium alloys. The four problematic streams are marked by ???. Coated semi-products are present in two of the four residues, namely in rejects and collected scrap. When these semi-products are recycled the amount and composition of the dross and salt slag residue is affected as well.During product design selection of the coating takes place, fixing the coating character¬istics and properties from this moment on for the rest of its life cycle. The choices made in the manufacturing phase are therefore critically linked to the recyclability of coated semi-products as well as the sustainability of the magnesium cycle as a whole. Sustainable closed life cycles, in which the quality of materials is preserved and residue creation and resource depletion are minimized, can be attained by selecting the appropriate alternative during product design. To realize this the effect of design choices on the life cycle and more specific the recycling process has to be known and quantified."

Jan 1, 2008

By Kenji Sasaki

Tamano Smelter started its operation in January, 1972 adopting FSFE ( Flash Smelting Furnace with Furnace Electrodes ) type smelting furnace at a production capacity of 101,00Ot/y of anode copper and 285,00Ot/y of sulfuric acid. Since then, it had experienced several production expansion program, it had twice as production capacity as start. 196,000t/y of anode copper and 436.000t/y of sulfuric acid. This time, we have completed the plan for increasing production capacity up to 226,000t/y of anode copper and 510,000t/y of sulfuric acid, by the oxygen enriched operation. We carried out several improvements and modifications, changing of cooling system ill FSFE, enlargement of converter and anode furnace, and some progresses in sulfuric acid plant and environmental facilities.

Jan 1, 1993

By V. Blet

Rare earth elements (REE) are regarded today as highly critical raw materials but currently lack suitable recycling processes. A combined hydro- and pyrometallurgical process aimed at REE recovery from used NdFeB permanent magnets was recently developed by the CEA. The process integrates the physico-chemical treatment of magnets, followed by a solvent extraction step for the recovery and intra-REE separation using a selective extractant. A subsequent pyrometallurgical treatment via molten chloride salt electrolysis allowed the isolation of pure Dy metal. Technical-economic assessment and life-cycle analysis were also conducted. Following this first successful demonstration, a new project aimed at the recovery of REE from end-of-life nickel-metal-hydride batteries is currently being developed in association with industrial and academic partners. The project aims at evaluating from an experimental and economic perspective different processes converging at the production of value-added products such as cermet materials for catalytic applications, purified REO concentrates, or metallic alloys.

By Robert Mensah-Biney

The loading characteristics of gold-tetrabromide species onto a weak-base resin, PAZ-4, were evaluated using a completely mixed batch reaction system. The time. to attain equilibrium loading was substantial, on the order of several days. However, abnormally high loading capacity values of 15 to 20 meq Au/g dry resin (1000 to 1300 kgAu/tonne) were attainable in 24 hours. The loading of gold-bromo species by P AZ-4 was visualized as consisting of two processes: (i) the rapid adsorption of [AuBr4r species by simple ion exchange mechanisms and (ii) reduction of [AuBr4r to metallic gold by an electron exchange mechanism. Elution of gold from loaded resin was feasible provided the resin had not been loaded to high capacity values. If loading is carried to high levels, complete elution becomes impractical and the gold may be recovered by ashing the loaded resin. For the high loading capacities observed this option would appear to be cost effective.

Jan 1, 1991

Primary sulphidic gold ores in the Archean provinces of Western Australia can be broadly sub-divided into pyritic, pyrite-telluride, arsenical and antimonial types. Pyritic ores contain only native gold, and are essentially not refractory. Arsenical ores almost always carry some invisible gold, and may vary from mildly to highly refractory. Pyrite-telluride ores contain gold-bearing tellurides, and are refractory to varying degrees. Antimonial ores usually contain aurostibite, and may be very difficult to process. A classification scheme for metallurgical processing, based on mineralogy, is proposed for the ores, and implications for processing are discussed.

Jan 1, 1995

By R. Stefaniuk, T. Le, J-Y Huôt, H. Henein

"One of the most important process variables in gas atomization is the gas to metal (G/M) mass ratio as it has a direct effect on the mean particle size of the atomized powder. If this ratio can be controlled during the atomization process, the powder produced would be more uniform and the d50 more predictable. Thus, atomization using a tundish or gravity feed from a crucible would be more stable. In gas atomization, the gas flow rate can be easily monitored; while it is very difficult to determine the molten metal flow rate. This research paper presents a new method of recording the molten metal height with time using a conducting metal height detector. The metal height recorded in real time during atomization was used to characterize using a model the friction losses in the metal delivery system. It is found that the integrity of the metal delivery tube and the cleanliness of the melt play a key role in the maintaining a stable metal feed.IntroductionIn the gas atomization process, molten metal is normally fed to the system either continuously using a tundish or in most cases a certain amount of metal is melted in a crucible and flows into the atomizing chamber under gravity. In the first case, the metal flow rate is believed to be constant during the atomization process despite the presence of slag or dross on the molten metal surface. In the second case, the amount of molten metal is depleted with time and the rate at which the metal flow decreases with time varies from test to test in a seemingly unpredictable fashion.' Furthermore, most atomization systems are confined units and the metal level in the crucible cannot be detected by a visualization method. In industry as well as in laboratories, the metal flow rate is normally calculated on either the mass of input material or the mass of total production divided by the duration of the test. This figure is not accurate enough and obviously cannot be used as a control parameter for the gas to metal ratio as it is only determined after the completion of an atomization run. The need exists for a metal flow rate measurement and control methodology; thereby the d50 of the powder produced may be estimated and controlled in real time. Clearly, the smaller the variation of the G/M ratio during the atomization process the more uniform the powder produced and hence the size of the particles can be predicted."

Jan 1, 1994

By S. J. Buckler

Many chemical and metallurgical processes use submerged gas injection to increase contact area between gas and liquid phases in order to promote faster overall reaction or refining rates. The total interfacial area produced by gas injection through lances, nozzles or tuyeres is both an important design parameter for new vessels and a measurement for estimating the maximum processing capacity of existing equipment. Estimating total interfacial area from submerged injection into industrial pyrometallurgical vessels from existing knowledge is a problem with two aspects. The first difficulty is the difference in behaviour of cold (aqueous) and hot (molten metal) systems, implying that existing models and correlations of gas-liquid behaviour developed in low temperature systems are not necessarily appropriate for estimation of high temperature behaviour. The second difficulty is the issue of scale-up of correlations from laboratory to industrial sized vessels. The work presented in this paper is part of an ongoing experimental investigation, at the GK Williams CRC for Extractive Metallurgy, to quantify the total gas-liquid interfacial area available in pyrometallurgical vessels using chemical measurement methods. The effects of three operating variables, injected gas flow rate, nozzle diameter and nozzle submergence, on total interfacial area are quantified in a IOOL aqueous system - the first stage of a three stage process in examining the implications for scale-up of high temperature, medium-scale results are discussed. The results of work at high, injected gas flow rates (up to 500/min) show that the submerged Froude number is not sufficient for use as the sole variable in a predictive model of total interfacial area. Further work is being undertaken to identify other dimensionless variables that will better represent the gas-liquid characteristics in submerged injection that influence the formation of total interfacial area. The second and third stages of the experimental investigation involve measuring the total interfacial area in a large-scale (1000L) aqueous sodium sulphite and small-medium scale molten metal baths.

Jan 1, 2002

By Adolf Mikula

Lead-tin solders are commonly used in electronic packaging due to their unique combination of electrical, chemical, physical, thermal and mechanical properties. Since it is known that lead and lead containing alloys cause great environmental concern and health hazards it is necessary to replace lead in solder materials. Besides the environmental concerns new technologies in electronic packaging require new and improved solders. In most cases the new solders will consist of ternary or quarternary alloy systems, the main component will be tin or indium and the second element could be bismuth, silver, copper and gold and to improve certain properties a third element will be added. For a third element zinc, nickel, antimony and aluminum can be considered. This report will concentrate on solders containing zinc as an environmental safe element.

Jan 1, 2003

By S. V. Ketov, V. P. Menushenkov, V. S. Shubakov

"The glass samples were obtained by melting of the oxides mixture SrO-Fe2O3-B2O3(Al2O3) at 1200-1250°C with subsequent quenching of the melt on quickly rotating steel roller. Submicronsized Sr(Fe,Al)12O19 particles were formed in glass-ceramic matrix during the crystallization aging of glass. The aging temperature Tag varied in the range 650-950°C. The submicron-sized hexaferrite powder was obtained by removing of the matrix phases using etching. The samples were characterized by X-ray diffraction, scamiing electron microscopy and magnetization measurements. The glass-ceramic material exhibits very high coercivity value up to 10 kOe. The samples of magnets were obtained by pressing of the hexaferrite powder at RT and subsequent aging in the range 900-1200°C. The aged samples exhibit coercivity value up to 8 kOe.IntroductionStrontium M-type hexaferrites have been widely used in technology and industry mainly for production of permanent magnets owing to their appropriate magnetic properties, chemical stability and low cost [1,2]. The SrFe12019-based compounds are characterized by high magnetocrystalline anisotropy and single easy magnetization axis. The highest coercivity is received for monodomain, defect-free single crystal particles with size D - 100 mn. Finely grained strontium hexaferrite prepared by chemical methods such as sol-gel pyrolysis and oxide glass crystallization exhibits high coercivity up to 6-8 kOe [3-5]. Owing to the partial substitution of Al for Fe in the strontium hexaferrite leading to the increase in the magnetic anisotropy field Ha=2Ki/M,, the increase in the coercivity may be received [6]. The notable results were achieved using the SrO-Fe2O3-AlzO3-B2O3 glass crystallization and formation of perfect submicron crystals of alumina-doped hexaferrite [ 6, 7]. The coercive force of glassceramics reached values of up to 10 kOe. Hexaferrite particles are well faceted and have the shape ofhexagonal bipyramids with truncated vertexes [7].In the present paper, we report results of our investigation into the SrO-Fe2O3-B2O3(Al2O3) glass crystallization, hexaferrite powders and permanent magnets, which were prepared by pressing submicron-sized hexaferrite powders at RT and subsequent sintering at 900-1200°C."

Jan 1, 2012

By Minh H. Pham

This paper presents a technique for imaging the extent of solidification of molten metal flowing in a cooled pipe based on the concept of eddy currents. A 3D mathematical model, which relates the geometry of solidification to the scattered field induced in a solenoid external to the pipe, is derived. The model is described by a set of integral equations which are solved numerically using the moments method. An iterative algorithm is developed to reconstruct the solidification distribution image. Experimental measurements have shown that the eddy current technique is sufficiently sensitive for practical purposes.

Jan 1, 2001

By Niko Hellstén

To capture efficiently the valuable trace metals from nickel slag using electric furnace, it is important to study their distributions between the slag and metallic phases in the furnace. It is impossible to calculate accurately these distributions without experimental measurements. Therefore, in this work, selected trace metal distributions and phase equilibria between K2O containing iron-silicate slags and a metallic Ni-Fe-Cu alloy in nickel slag cleaning furnace conditions were studied. The experimental method developed and applied during the work, involved a modified quenching technique that included equilibration of the samples in semi-sealed quartz ampoules in an inert atmosphere and metallic Fe saturation. The use of the semi-sealed quartz ampoule prevents the escape of volatile elements from the sample during equilibration. Chemical compositions of the phases and the trace elements were analysed by EPMA. From the measured compositions, the trace metal distribution coefficients between the molten Ni-Fe-Cu alloy and slag were calculated.

By A. Treverrow, G. A. Brooks, H. K. Worner

"The work by H.K Worner and co-workers at CRA in the 1960s, and early 1970s, established that molten metals could be refined continuously utilising counter current flow of metal and slag. Womer also demonstrated that counter current refining could produce highly refined metal products. These developments coincided with the advent of high intensity metallurgical reactors in both the ferrous and non-ferrous industries (e.g. BOS, Q-BOP and later Sirosmelt) that utilised high levels of gas injection to produce rapid stirring and very fast reaction. These new generation of high intensity metallurgical reactors allowed high tonnage rates through relatively small volume vessels.Whilst, it is well known that the counter current flow of reacting phases offers the potential of efficient mass transfer and high purity products, the application of counter current reactors to molten metal/slag systems has been criticized on the basis that they suffer from either low intensity or, alternately, from poor refining due to excessive dispersion. These criticisms relate to the balance between intensity and the refining capacity of a reactor. That is, whilst high levels of mixing transversely to the direction of flow promotes high mass transfer, longitudinal mixing (dispersion) is detrimental to refining. Of course, mixing in one direction invariably leads to mixing in other directions, thus creating a playoff between high mass transfer and excessive dispersion.This balance between intensity and refining has been the subject of recent studies overseas, and at"" the University of Wollongong, using cold modelling techniques to evaluate the effect of mixing on dispersion in a counter current refining launder. These studies have shown that for a given geometry and mixing regime, dispersion decreases with increasing flow of liquid phases. This means that whilst high mass transfer cannot be achieved in a refining launder without sacrificing the degree of refinement, there is no impediment to achieving high productivity through such a system, in fact, high through puts may favour good refining. Thus, it may be possible to match a high productivity smelting operation with a equally productive counter current refining stage."

Jan 1, 1996

By Mikula Adolf

Lead-tin solders are commonly used in electronic packaging due to their unique combination of electrical, chemical, physical, thermal and mechanical properties. Since it is known that lead and lead containing alloys cause great environmental concern and health hazards it is necessary to replace lead in solder materials. Besides the environmental concerns new technologies in electronic packaging require new and improved solders. In most cases the new solders will consist of temary or quarternary alloy systems, the main component will be tin or indium and the second element could be bismuth. silver, copper and gold and to improve certain properties a third element will be added. For a third element zinc, nickel, antimony and aluminum can be considered. This report will concentrate on solders containing zinc as an environmental safe. element.

Jan 1, 2003

By Michael G. Mayer

Since its invention in 1859 various designs of lead batteries have evolved to meet commercial needs for traction applications and standby power. In recent years major developments have taken place in lead alloys and the chemistry and mechanical design of industrial lead batteries. These are reviewed in relation to their commercial application together with the new type of maintenance free gas re-combination lead-acid batteries which are opening so many new markets for lead.

Jan 1, 1990

By Alistair Burrows

Situated in the oblast of East Kazakhstan, the Ust-Kamenogorsk Metallurgical Complex has spent the past twenty years renovating and remodelling itself as a modern polymetallic sulphide smelting facility, and a regional centre of excellence for custom smelting. Along the way there have been changes to the company structure, introduction of new technologies, investments in expanded capacity, environmental improvements, and addition of new metal products and by-products to the site’s repertoire. These changes have been gradual and incremental, but taken together they represent a significant contribution to placing Kazakhstan’s sulphide smelting industry on a strong foundation for enduring success in the international custom smelting market. In achieving these changes, a workforce that was historically isolated from much of the world now has recognised expertise, internationally competitive skills, and confidence to embrace the future. Further improvements in energy efficiency, environmental compliance and polymetallic processing capabilities are challenges that UKMC stands ready to face.

By Batric Pesic

Silver dissolution with thiourea was studied by using the rotating disk technique. The major parameters studied were: thiourea concentration (0-0.5M), ferric sulfate concentration (0-0.5M), sulfuric acid concentration (0-0.5M), and the effect of many foreign ions (Mn, o.i, Co, Ca, Na, etc.). Temperature effect was studied in the range 5-35 .C. The activation energy was 5.4 Kcal/mole. The dissolution of silver was first order with respect to ferric sulfate, and the secord order with respect to thiourea. Among the additives, copper had a dramatically negative effect. The strong oxidants such as hydrogen peroxide and manganese dioxide were also detrimental for silver dissolution. Silver does not dissolve with thiourea in the absence of ferric ions. Sulfuric acid does not participate in the dissolution reaction either. Chemically, the most important parameter for silver dissolution is the ferric sulfate/thiourea ratio. Thus, in the solutions with excess of ferric sulfate, a solid silver-thiourea complex is formed, which precludes transfer of silver into solution. In the solutions with the excess of thiourea, the free thiourea reacts with formed solid silver-thiourea complex and silver goes into the solution. The solid silver-thiourea complex was characterized according to its chemical composition. The complex contains 6.54%C, 2.49\H, 14.77%N, 16.09%0, 21.62%8, and 37.13% Ag. This composition corresponds to a Ag2so4.3&apos;1U.2ff:i0 compound The soluble silver species are present in the solution as the dimers of AgTU+3 complexes.

Jan 1, 1989