Search Documents

By D. J. Maconochie

This paper describes the investigations and results of monitoring of deformations of houses located within the area of influence of a pillar collapse over the Westfalen No. 3 coal mine near Ipswich, Queensland. The subsidence resulted in minor subsidence of at least 18 modern houses and serious damage to 4 others. The history of the events and the measures taken to deal with the physical problems arising are described. The investigations and results are described and related to the mining methods and geology. The stability of coal pillars up to 9.6 m high was considered and computer modelling undertaken to relate surface subsidence to estimates of the extent of pillar failure. Assessments were made of the likely extent of subsidence during the incident. Measurements of distortion and tilt were obtained as the ground slowly subsided and criteria established to determine when the structures were deemed to be unsafe. Detailed surveys of houses affected or anticipated to become affected were also undertaken. Four houses were condemned and subsequently demolished as a result of excessive tilt. The methods of assessment are described and the implications of the results related to the various house designs.

Jan 1, 1992

By Fernando O. L. Xavier

"The Barro Branco coal mine was located in the southern region of Brazil, in the state of Santa Catarina. In 2002, an incident occurred at the mine, leading to a violent, massive pillar failure, resulting in almost 100 failed pillars in less than 3 hours, totaling nearly 700 collapsed pillars after a period of 6 weeks. The paper outlines the geological and operational conditions before the accident and analyzes the primary factors leading up to the event. This paper also discusses and examines the unusual characteristic of violent, uncontrolled pillar bursts that occur over a longer timespan, in comparison to other equally violent but rapid events, such as those that occurred at the Crandall Canyon Mine, at a Book Cliffs District mine, and at the Solvay Mine. INTRODUCTION The southern region of Brazil holds 100% of the coal reserves for the country, and half of it is located within the state of Santa Catarina. Almost the entire Brazil’s coal production, around 8 million tonnes/year, is consumed for electricity generation. Most of the coal mines in Santa Catarina are underground room-and-pillar mines, and most are shallow mines, with depths of cover ranging from 20 to 400 m. The Barro Branco mine, near the city of Criciuma, experienced a violent mine collapse at the end of March 2003, which was analyzed and discussed by Zingano, Koppe, and Costa (2004). The event consisted of violent failure of 100 pillars in less than 3 hours, and a subsequent failure of approximately 700 additional pillars over the next 6 weeks. After the panel collapsed, the mine was closed due to unsafe conditions as a consequence of the seismic event. A map of the collapsed area is shown in Figure 1. GEOLOGY AND MINING METHOD There are two coal seams mined at Barro Branco mine. The first is the 1.5 m to 2.3 m thick Barro Branco Seam, under about 75 m of cover. The second is the Bonito Seam, where the collapse occurred. The Bonito Seam is 2.5 to 5.5 m thick located at a depth of approximately 80 m, with an average dip of 0° to 15°. Various major faults and inherent joints are present in the area."

Jan 1, 2017

By J. Nielen van der Merwe

During the process of pillar extraction at the Welgedacht Colliery, an unexpected pillar collapse resulted in the entrapment of equipment. The area was visited soon after the event to evaluate the stability of the area for the purposes of extracting the equipment. It was found that the area had stabilised sufficiently to allow work without undue risk to the safety of workers. The equipment was reclaimed successfully. A subsequent investigation into the reasons for the collapse was conducted. It entailed detailed underground and surface subsidence observations and numerical modeling. It was found that none of the perceived negative factors that were present at the time could result in pillar loads that were sufficient to cause the collapse. It was concluded that the local pillar strengths were less than the nationally used value and that they were possibly further reduced by aging.

Jan 1, 1999

By Russell C. Frith

This paper presents recent findings concerning longwall caving mechanisms relating to Australian mining conditions and their effect upon longwall support requirements and behaviour. The findings arc based on a program of intensive hydraulic support monitoring in a variety of Australian mining conditions coupled with geotechnical observations. Results from the study illustrate periodic weighting cycles of varying severity and these are related to the overlying geology in terms of the strength of individual strata units, their thickness and proximity to the longwall extraction. Several different caving mechanisms are identified which contribute to periodic weighting cycles. The importance of recognising weighting cycles in relation to the operation of the longwall face will be discussed in detail. Longwall support design methods are critically examined in relation to the case histories of the monitoring program. The applicability of the said design methods to Australian coal mining conditions is discussed and an outline of design considerations to facilitate productive longwalling is presented. Overall, the paper only "scratches the surface" of the work currently being undertaken by ACIRL in this area, and the findings of that work.

Jan 1, 1992

By Kenneth Rigsby

Black Mountain Resources' Highlands Mine No. I is a full extraction room and pillar operation located in Harlan County, Kentucky. Black Mountain extracts the 0.9 to 1.1 meter (36- to 42-inch) thick Owl Scam that is situated 60 to 70 meters (200 to 235 ft) above the longwall panels of the abandoned Arch No. 37 Mine, in the 3.4 meter (I I ft) thick Harlan Scam. In the areas where full extraction has taken place, the overburden above the Owl Seam ranges from 60 to 430 meters (200 to 1,400 ft). A short room and pillar panel was developed above an extracted longwall panel to test the selected pillar size, to evaluate support systems, and to verify the shape of the subsidence profile over the recovery end of the depleted longwall panel. It is over the recovery end that Highlands Mine No. I would access the Owl Seam reserves that exist above the No. 37 Mine. Black Mountain selected pillars sizes to be employed above the longwalls based on the ability to fully extract a pillar employing extended cuts. After a mechanical testing program was completed and mine behavior and top disturbance were observed in the test panel, John T. Boyd Company (BOYD) verified pillar stability and designed support systems. BOYD previously designed No. 37 Mine's gate pillars and studied subsidence and gob formation over its longwall panels; this effort aided the analysis of overburden movement and pillar integrity at Highlands Mine No. 1.

Jan 1, 2003

Design and selection of support systems for longwall faces call for in-depth knowledge of strata mechanics and in particular of strata-support interactions. The paper presents the results of field investigations and analysis of a difficult-to-cave roof using powered supports under a massive dolerite sill in Central India using a state-of-the-art datalogger system. The mechanised longwall face was equipped with 4/680 tons chockshields operated on the IFS mode using a 300 K W DERD shearer. The datalogger system was capable of storing data simultaneously in 32 channels. The paper describes the monitoring system and the monitoring programme. The system provided useful information on support behaviour, build-up of leg pressures and face convergence during an intense dynamic periodic weighting phenomenon which destroyed the integrity of almost half of the face supports. At this point, the face had advanced by about 197 metres from the barrier. The paper outlines a post-mortem analysis of this dynamic event and provides a critical evaluation of the data collected for understanding strata support interaction and the behaviour of the massive sill in the overburden.

Jan 1, 1992

By Michael Karmis

During the last 25 years, technological advancement and subsidence research have resulted in more accurate and diverse prediction capabilities. The work presented in this paper focuses on the development of integrated prediction capabilities for dynamic deformation indices and for strains over sloping terrain. In order to assist subsidence engineers with accurate prediction methodologies, the research also addresses the development and validation of techniques that can enable model calibration using alternative measured subsidence parameters such as horizontal or ground strain instead of the traditional vertical subsidence values. This paper presents the basic concepts and validation of the above mentioned enhanced prediction and control methodologies, which are necessary for effective assessment and control of mining-induced subsidence, using examples and case studies. In addition, a risk assessment approach for evaluating landscape stability over mined areas is presented. The enhanced prediction methodologies have been incorporated into the Surface Deformation Prediction Software (SDPS) package.

Jan 1, 2008

By Kirk W. McCabe

RokLok binder is a two-component polyurethane system consisting of a polymeric isocyanate (Component A) and a polyol resin (Component B). The two chemicals are mixed and injected into the mine rock under pressure. The initial low viscosity enables the RokLok material to permeate many of the smallest fractures. About 3-5 minutes after injection, the reacting material begins to expand in the fractures; the reaction is completed after 1-2 hours, and the material sets to a mechanically strong binder which adheres tightly to the rock. The consolidated rack provides resistance to any further f movement w thin the strata. The RokLok binder injection system is fast becoming an important engineering tool for coping with adverse underground geological conditions. Two case histories discussed in this paper, a longwall mining problem and an entry-roof problem, demonstrate the effectiveness of using the RokLok binder system to help solve complex ground-control problems in a cost-effective manner.

Jan 1, 1981

By Yunqing Zhang

The 3-D numerical modeling using ABAQUS is performed to analyze the mechanisms of the tensioned bolts by taking into considerations excavation sequence, pre-tension, bedding planes and in-situ horizontal stresses. The effect of the pre-tension and the mechanisms of the tensioned bolts are analyzed based on the results from the modeling. Based on field observations, the failure modes for the tensioned bolted strata are classified by their causes and failure mechanisms. The support design consideration for each failure mode is given. Finally, a new design approach is proposed to do the tensioned bolting design using numerical method.

Jan 1, 2002

By Gregory Hendon

Jim Walter Resources, Inc. (JWR), has successfully longwall mined for many years at depths ranging from 1200'-2500'. However, full pillar extraction has proven difficult and generally economically unfeasible. Overburden and redistributed stresses at these depths require relatively large pillars, which become unmanageable with most pillar extraction practices. The economic benefits of taking gateroad pillars as part of a longwall face have been recognized for some time, including increased life of mine recovery, elimination of belt moves, reduced overcast requirements, and improved longwall to continuous miner ratios. Until recently, the associated risks of pulling pillars prevented any extensive use of this concept at JWR. Due to geological, economic, and longwall repeatability problems, JWR accepted the risks, and undertook pillar extractions with longwall faces in several different applications. The applications included taking a stable pillar (250' wide) as a longwall panel, taking yield pillars on the headgate and tailgate of panels, taking yield pillars and stable pillars in the middle of a panel, mining through chain pillars in the middle of a panel, and taking a support pillar on the tailgate end of a panel. This paper describes the background and experience of pillar extraction with longwalls at JWR.

Jan 1, 1998

By André Zingano

Pillar collapses have been studied for several years and can be classified into two types: nonviolent squeeze or violent pillar collapse, i.e., controlled or uncontrolled pillar collapse. Underground coal mines in Brazil are considered shallow mines, because the overburden thickness varies between 20 and 400 meters. For this reason, the coal pillars should be designed as permanent pillars to avoid subsidence and groundwater problems. In the last two years, various pillar collapses occurred, one being a violent collapse and the others being squeeze collapses. All these collapses were considered massive pillar collapses because many pillars were involved. In the violent pillar collapse case, the width¬to-height (w/h) ratio was less than three; although, the pillar safety factor (SF) was more than 1.3. There was a collapse of about 100 pillars in less than three hours. The objective of this study is to determine the mechanism of pillar collapse for this violent pillar collapse. Convergence monitoring and numerical modeling were applied to combine field data and theory to simulate the pillar collapse. Convergence field measurements introduce the arc-effect behavior for the roof. The results showed that other factors besides pillar geometry caused the pillar failure. Other parameters, mainly dip of the coal seam and presence of fractures and faults may affect the strength and failure mechanism of a pillar.

Jan 1, 2004

By Nicholas P. Kripakov

The unpredictable massive collapse of roof in openings developed under apparently safe and stable roof conditions in coal mines of the United States has been of much concern for many years. One type of massive caving phenomenon is often attributed to cutter roof, a failure that initiates at one and/or both upper corners of an entry and propagates nearly vertically resulting in overall failure with little or no warning. This paper reviews current methods being used to control cutter roof and suggests new alternatives. The impact of basic parameters that include mine geometry, overburden geology, rock properties, and in situ stress conditions is discussed in the context of their relationship to this problem. The effects of various stress control measures are investigated with model analysis to gain insight into means of reducing the high level of stress known to exist at the entry corners of a West Virginia coal mine prone to cutter roof. The results are presented in the paper and the feasibility of their practical implementation is discussed.

Jan 1, 1982

By Joseph C. Zelanko

Cable bolt support techniques. including hardware and anchorage systems, continue to evolve to meet U.S. mining requirements. For cable support systems to be successfully implemented into new ground control areas, the mechanics of this support and the potential range of performance need to be better understood. To contribute to this understanding, a series of 36 pull tests were performed on 10 ft long cable bolts using various combinations of hole diameters, resin formulations, anchor types, and with and without resin dams. These tests provided insight as to the influence of these four parameters on cable system performance. Performance was assessed in terms of support capacity (maximum load attained in a pull test), system stiffness (assessed from two intervals of load-deformation), and from the general load-deformation response. Three characteristic load-deformation responses were observed. An Analysis of Variance identified a number of main effects and interactions of significance to support capacity and stiffness. The factorial experiment performed in this study provides insight to the effects of several design parameters associated with resin-anchored cable bolts.

Jan 1, 1995

By Jay Hilary Kelley

This paper proposes a modification of longwall roof support to meet new difficult mining conditions that are anticipated in the future. A gob canopy is a movable appendage attached on the rear of a longwall shield to counterbalance the troublesome forward downward force couple (FDFC). The gob canopy can be swung in both vertical and horizontal directions, powered by hydraulic cylinders. Several functions and applications are de- scribed

Jan 1, 1997

By Kot F. von Unrug

One of the major difficulties in the proper characterization of rocks surrounding excavations is the lack of data. The existing method for strength determination requires core drilling for sample collection, which, when performed from the surface is costly, and when performed underground, in addition to its cost, interferes with the mine operations. I-landling samples tested in the laboratory is troublesome and also influences the obtained results. Over several years. the author has been interested in developing a method of in situ strength determination that could rapidly generate strength data at low cost without a negative effect on mining activities. The recently developed borehole penetrometer is an improved version of the initial design ( 3 inches in diameter), which was used mainly for strength determination of coal pillars. The new penetrometer has been designed to work in 1.5 inch diameter holes. Such holes can be drilled at low cost with either hand held drilling machines or roof bolters. eliminating limitations of the previous system and opening the possibility of broad application. Strength testing of roof rock around longwall pillars is an example of an obvious benefit when designing secondary roof support. In the paper are given the principles of work of the apparatus and examples of the obtained strength data.

Jan 1, 1998

By Dennis R. Dolinar

Roof falls, even of supported roof, still constitute a major hazard in underground mines. However, associated with any fall or instability is a pattern of roof movement. Therefore, the National Institute for Occupational Safety and Health, Pittsburgh Research Center, has been conducting research into the development of practical extensometer systems that can be used to measure this displacement and to determine if a roof fall may occur, thus increasing miner safety. For extensometers to be used in the detection of potential roof falls in coal mines, an understanding of the movement and displacement rates that will lead to roof failure is required. Because roof falls are unpredictable, it is often very difficult to obtain this information. Therefore, in a coal mine in the lower Kittanning seam in Pennsylvania, a room widening experiment was conducted to intentionally cause a roof fall while roof movement data was collected. In this experiment, two adjacent rooms 5.5 m (18 ft) wide supported with 1.5 m (5 ft) resin-grouted bolts and instrumented with extensometers were widened to 9 m (30 ft). In one of the rooms, 3.6 m (12 ft) cable bolts were installed as supplemental support. In the room with no additional support, a roof fall occurred 72 h after the room was widened. Much of the 3 cm (1.2 in) of movement in this room resulted from the instantaneous and transient response to mining with displacement rates up to 7.6 cm/d (3 in/d) being measured. This was followed by a steady state displacement phase with a rate of 0.43 cm/d (0.17 in/d). Just 12 h before the fall, movement deeper in the roof caused the rate to accelerate to 1.1 cm/d (0.44 in/d). The roof in the room with the supplemental cable support did not fall even though the total roof deformation was over 7.6 cm (3 in). Significant roof movements and strains in the cabled room were detected to a depth of 3 m (10 ft) while maximum cable loads were over 180 kN (40,000 lbf). Essentially, the roof was in postfailure with the cables maintaining the material, while roof stability was indicated by a steady state displacement rate of only 0.025 cm/d (0.01 in/d) at the end of the test.

Jan 1, 1997

By Gheorghe Oncioiu

The phenomena developed on the influence of thick coal seam no.3 mining, by horizontal slices and rocks caving roof control, in the Jiu Valley coal basin, are very complex. By analyzing the influence volume of underground faces and defining the stress and strain zones, around the faces, it is possible to evaluate the suitable powered support performances. Also, Jiu Valley thick coal seams involve about 50% of reserve balance in the main safety pillars of social, industrial and natural objectives, situated on the mining surface perimeters. For a correct design and drawing of main safety pillars complex research was done with the aim of establishing the subsidence parameters. Upper face rocks medium could be assimilated as a granular medium, which is in a permanent movement. For describing the rocks movement, respectively the ground surface displacement, was taken into account the stochastic mechanics principles. The theoretical solutions are in accordance within situ measurements.

Jan 1, 1999

By David Miller

Longwall gateroad support can be supplied by a variety of methods. The system of support also needs to be flexible as conditions change. This is especially true in the complex geological conditions of the west Kentucky # 13 seam. Methods of gateroad support used in this seam will be presented along with the successes and failures of the systems as conditions changed Lodestar Energy's gateroad support progression through the seven longwall panels retreated to date will provide an insight into planning for future panels

Jan 1, 1998

By Thomas M. Barczak

A survey of the longwall industry was conducted to examine the performance of modern shield technology. The results of this survey indicate that state-of-the-art shields perform better and last longer than ever before, but premature failures do still occur. In addition, longwalI operators are now using shields longer than ever before and a greater number of fatigue related failures on aging shields are now occurring. A generic assessment of these shield failures is provided, describing the nature of the failures and how widespread they are throughout the industry. An engineering assessment of shield design and factors that cause shield failures is made using both strength of materials and fracture mechanics principles. From this analysis, design practices to improve structural margins of safety and extend the life of the shield are proposed. The existence of unexpected shield failures indicate that current shield performance testing is at times inadequate. Recommendations are made relative to improved shield performance testing protocols including the benefits of testing in an active load frame such as the National Institute for Occupational Safety and Health's (NIOSH) Mine Roof Simulator. Even the most rigorous shield testing procedures, which strive to simulate in-service loading conditions, fail to consider key environmental issues, such as corrosion which is often the cause of structural fatigue failures in modern shields. The survey also indicated that hydraulic failures occur much sooner in the life cycle of a shield than structural failures, and although they can significantly degrade support capability, often go undetected for long periods of time. Methods to detect the hydraulic failures are also provided. The paper concludes with key points to maximizing shield design and life expectancy and ideas for future generation shield designs.

Jan 1, 1999

By Danny J. Van Roosendaal

An investigation was undertaken to determine hydrogeological effects of subsidence over a longwall coal mine in the Illinois Basin. At this mine, approximately 200 ft of bedrock overburden is overlain by up to 150 ft of glacial till and localized water-bearing glacial sediments within a buried bedrock valley that overlies the longwall panel. A finite-element mechanical model of the subsided longwall panel shows sufficient strain to enhance permeability throughout the bedrock portion of the overburden. However, examination of the actual surface subsidence profile indicates that the overburden deformation is localized in narrow zones at the panel edges. The aquifer units at the base of the glacial sediments are confined by glacial clays (above) and weathered shales (below). Elevated water levels were observed in the glacial aquifers during subsidence, which indicates that the clays and shales maintained confinement as the overburden subsided and deformed. A three-dimensional ground-water flow model was used to simulate the effects of subsidence on the hydrogeologic system and to estimate inflows into the mine. Longwall retreat was simulated by several model runs, each representing a new longwall face position. Simulated heads and mine inflows were calibrated with recorded water levels and observed inflow conditions by modifying the hydraulic conductivity of particular model layers. Model calibration indicates that the permeability of certain lithologies, such as plastic underclays and weathered shales, is not significantly enhanced by subsidence. A worst-case scenario was simulated by inserting a deeply incised, sandfilled valley into the model, which had only minimal impact on the simulated mine inflows.

Jan 1, 1995