Search Documents

A glance at the following chart reveals that because of the continued poor economy, the slump in industrial mineral production continued into 1980. Gypsum was down 17% from 1979; cement down 9%, sand and gravel, 17%, and crushed stone, 11%. All these downward trends reflect the high interest rates and high costs that slowed construction starts. Domestic fluorspar was down 21% and imports off 14% due to the steel iudustry slump. However, potash production was up 8% and phosphate, 5%. Increased drilling activity spurred au increase in barite production of 25%. Most other industrial minerals posted losses with only a few insignificant increases. As expected, prices were higher, reflecting increases due to high costs for labor, supplies, and above all, energy. Increasing energy and transportation costs also had their effect on industrial mineral production. Railroad freight rates increased 16-22% including fuel surcharge; truck rates increased 11-14%a; and ocean freight rates increased 20% for finished goods. The 1979 shortage of boa and hopper cars did not continue into 1980-most likely due to low production of many of the hulk industrial mineral commodities. All in all, 1980 was not a good Year for industrial minerals.

Jan 5, 1981

By M. D. Max, A. H. Johnson

INTRODUCTION Gas hydrates have considerable potential to be a major energy resource owing to their apparent abundance in Arctic regions and along continental margins throughout the world (Kvenvolden, 1988). Yet, the oil and gas industry has been slow to pursue this opportunity. The primary reasons for this are the large conventional reserve base for natural gas worldwide and the perception that gas hydrate will not be a viable resource for another twenty or thirty years. Gas hydrates are thus viewed as a potential resource for the distant future, but not a valid investment for the near term. This paper addresses both global gas markets and gas hydrate technology, and shows that the commercial development of gas hydrate could proceed rapidly enough to constitute a near-term energy resource. GLOBAL GAS MARKETS The proven worldwide reserves of conventional natural gas are truly enormous, totaling over 6,000 TCF according to BP (2004). Moreover, those reserves have nearly doubled during the past two decades and now represent 67 years of consumption at the current production rates of 80 TCF per year (Fig. 1). This reserve increase has occurred even as global production of natural gas has increased by 67% during the same two decades (Fig. 2). While declining conventional gas reserves are a concern in North America, especially in regions where established infrastructure exists to bring gas to consumers, large new discoveries continue to be made elsewhere in the world. Indeed, in many parts of the world (such as the Middle East and parts of West Africa), natural gas has been regarded as an essentially worthless byproduct of oil production or exists in stranded gas fields. Given this situation, pursuing unconventional gas resources that are inherently riskier exploration targets and more expensive to produce would appear to have little rationale from a business standpoint.

Jan 1, 2006

By P. Mousset-Jones

The USBH Mining Systems and Ground Control Generic Research Center funded a project leading to the improved planning of airflow and refrigeration in underground mines experiencing hot working conditions. The project was broken down into approximately five phases: 1. Visiting some of the known hot mines in the U.S. and sending out a questionnaire to determine other mines which might be experiencing hot working conditions in the future. 2. Choosing two mines in which to conduct measurements to determine the insitu rock thermal conductivity and diffusivity, and comparing these values with laboratory determined values. 3. Investigating computer programs available for mine climate simulation, and testing these programs with case study examples from the two mines where the rock thermal properties were measured. 4. Considering improved ways of estimating the wetness factor and experimenting with the use of heat flux meters to more directly measure the rock heat inflow into the airstream. 5. Applying the results of these investigations to simulating the climate for future mine development and production areas at the two- mines. The project is approximately two thirds completed. At the time of writing, the insitu measurements at one of the mines are still being recorded. This paper will be describing the procedures and results of the insitu rock thermal property measurements, and give a brief description of some of the simulated results obtained for a mechanised cut and fill stope case study from the Homestake Gold Hine in South Dakota.

Jan 1, 1985

By B. Mishra, A. Staley, D. Kirkpatrick

The major waste product of the alkaline extraction of alumina from bauxite [Bayer Process] is known as red-mud. Approximately, a ton of red-mud is produced for every two tons of bauxite mined. The red-mud produced from Jamaican bauxite is rich in hematite, alumina and titanium oxide. It has been shown that over 90-wt. pct. alumina can be recovered from red-mud by soda-ash sintering and caustic leaching. Hematite can be carbothermically reduced with a degree of metallization of over 94 pct resulting in attempts for magnetic separation. These separations are desirable in the notion that there is no waste product generated from this type of processing and consequently an opportunity for complete utilization of the waste material. Conversely, the pre-separated material could be charged through the tuyeres in an iron blast furnace or smelted to produce pig iron. If smelted, the concentration of titanium oxide in the slag will be significantly high justifying its recovery by established acid-leach process. This paper describes the results of alumina recovery and the plans for titanium oxide recovery from red-mud. In addition, the situation of ongoing efforts in iron extraction, particularly, the method of magnetic separation of the reduced material. The problems associated with the use of reduced red-mud as an alternative to direct-reduced iron [DRI] has also been discussed. Critical assessment of the recovery sequence chosen for the products has been described based on economics.

Jan 1, 2001

By J. O. Marsden

Over the past eight years, Phelps Dodge (a subsidiary of Freeport-McMoRan Copper & Gold, Inc.) devoted a significant amount of effort to the development of a suite of processes for the effective hydrometallurgical treatment of copper sulfide concentrates. This effort resulted in the development of high-temperature (>200ºC) and medium-temperature (150° to 165ºC) pressure leaching processes. Specific configurations of both processes have been commercially demonstrated at Phelps Dodge?s facility in Bagdad, Arizona. This paper reviews in detail the chemistry of medium-temperature pressure leaching of copper concentrates and reports on the process development work conducted by Phelps Dodge and others for this technology. This paper is Part I of a four-part series on this technology. Part II covers the development of medium-temperature pressure leaching and direct electrowinning technology; Part III considers the large-scale demonstration of the MT-DEW-SX process at Bagdad, Arizona; and Part IV addresses the development and design of a full-scale commercial application at Morenci, Arizona.

Jan 1, 2007

By Charlie Watts, Ken Smales, Ron Fleming

The Manapouri Power Station is an underground hydro-electric station located in the South Island of New Zealand, and was constructed in the 1960s. Between 1997and 2002, a second 10m diameter tailrace tunnel was constructed to increase the out-put and to improve the overall hydraulic efficiency and output of the station. A critical economic and project approval consideration for the second tunnel was the outage time required for the breakthrough into the power station. The power station is in part dedicated to providing power to an aluminum smelter with the balance to the National Grid, and apart from the physical problems associated with providing an alter-native power supply to the smelter, the loss of generation revenue and supply risk were significant issues. Innovative planning reduced the planned outage time from several months to21 days, and the breakthrough was eventually achieved in 11 days as a result of additional value engineering measures implemented during construction. This paper describes the engineering optimization that took place during the planning stages of the project and later during construction, as well as describing the construction methodology used.

Jan 1, 2007

By T. Weatherwax

As part of a strategic research initiative at UBC to design and evaluate integrated underground mining and mineral processing systems, work has been done to determine how to utilize the coarse rejects of pre-concentration in the underground environment. An amenability study for nine orebodies from four of Xstrata Nickel?s Ontario operations evaluated both processing and waste disposal methods. The utilization of the rejects as a high quality backfill with minimal binder requirements has been identified as the preferred disposal method. Fill mixes utilizing the rejects in combination with classified tailings, full tailings, and cement were developed based on the geotechnical properties of the rejects. The mix designs were examined for both strength and rheological properties. The paper will present the results of the pre-concentration testwork, the design and strength testing of various mix designs for rejects from the nine ores and presents a conceptual design for an underground pre-concentration system based on this test work.

Jan 1, 2008

By S. E. Chetlin

In the mid-1970?s, the market value of tangible assets of S&P 500 companies far outstripped the value of intangible assets, including intellectual property (e.g., 83% tangible assets v. 17% intangible assets).1 By 2005, the picture was quite different. By that time and continuing to 2010, S&P 500 companies? market value of intangibles was about 80%, with tangible assets accounting for only 16% of market value.2 This swing highlights the importance in today?s world of understanding intellectual property rights and varying strategies and options for protecting them. This paper discusses intellectual property rights particularly patents and trade secrets, specifically: 1) types of intellectual property; 2) choosing the mode of intellectual property protection; 3) obtaining patent protection; and 4) using patents as a sword versus a shield.

Jan 1, 2012

By Gary J. Fletcher

Mining and processing activities which are proposed on private land, state leases, or unpatented mining claims are governed by numerous local, state, and federal laws which identify the procedures and conditions which must be met before resources can be developed. The respective government agencies responsible for the administration and enforcement of these laws have promulgated supporting regulations and guidelines, and have implemented certain permit and approval processes to ensure compliance. Each exploration project has a unique environ- mental setting and location which further dictates the types of air, water, hazardous waste, and wildlife laws and regulations which must be complied with before development commences. The environmental planning process should be the first step in the evaluation of existing company properties and the potential acquisition of other mineral properties. However. many company don't consider the environmental requirements for a project until the decision is made to develop the property for mining and processing. If a mining company wants to expedite the environmental planning process, it must first develop an in-house process for evaluating the project and determining the environmental approval procedures in the state where the project is located. The first stage of environmental planning involves general information which can set the overall company philosophy for development of projects.

Jan 1, 1987

By K. Bounou, K. Komnitsas

"Risk quantification may be used as a sustainable development index in the mining industry, since it encompasses both economic and social factors. In addition, it may assist in the development of a framework, which is also indirectly related to sustainable development, to prevent accidents and improve health and safety standards. However, risk quantification in the mineral sector involves diverse activities and is considered a very difficult task. Although statistical data report accident severity rates, incident rates and accident frequency rates, none of these allow for accurate risk calculations. In this paper, two risk calculation formulas, which may be used to quantify risk, as well as to identify hazardous activities in a workplace, are proposed. Numerical examples are given based on statistical data available through the MSHA database. Also a combination of a decision/fault/event tree that allows risk quantification is presented."

Jan 1, 2005

By C. G. Anderson

Today, with a stringent economic and environmental climate prevailing in the copper business, there is increased interest in evaluating new processing alternatives for production. Hydrometallurgical pressure oxidation of copper concentrates is one of the more viable approaches and several technological candidates have emerged. Of these, an overlooked but, ironically the first industrially proven methodology, utilized nitrogen species catalyzation in the oxidizing pressure leach system to produce copper via SX/EW. Given its many inherent process advantages, this may prove to be a feasible process alternative for the future. In this paper, the history of the system and its application to copper concentrates and ores will be outlined. In particular, a novel methodology for effective recovery of precious metals from chalcopyrite concentrates will be discussed. Finally, the perceived economics of chalcopyrite concentrate treatment with this unique industrially proven process will be delineated.

Jan 1, 2001

Several years ago, Hudco Industrial Products began experimenting with the idea of levitating a conveyor belt with a film of air, much like the puck on an air-hockey table. While conducting its research, the company found out that some Russian and Dutch companies attempted the concept during the 1970s. After studying those conveyors, Hudco determined that its design was better. The Hudco advanced air-supported conveyor consists of an air-tight plenum, or chamber, that runs the length of the belt. The topside of the plenum has a formed trough. It corresponds to the profile of conventional troughing rollers. Low-pressure air is provided to the sealed plenum from a low horsepower blower. This pressurized air is metered and released through the central portion of the trough and reacts against the underside of the belt. The differential pressure between the top and bottom surfaces creates the lift to support the loaded belt. Airtight covers are installed to seal the transported materials in the plenum trough.

Jan 1, 2002

By B. Anameric

The pig iron nugget process is gaining in importance as an alternative to the traditional blast furnace. Throughout the process, self-reducing?fluxing dried greenballs composed of iron ore concentrate, reducing-carburizing agent (coal), flux (limestone) and binder (bentonite) are heat-treated. During the heat treatment, dried greenballs are first transformed into direct reduced iron (DRI), then to transition direct reduced iron (TDRI) and finally to pig iron nuggets. The furnace temperature and/or residence time and the corresponding levels of carburization, reduction and metallization dictate these transformations. This study involved the determination of threshold furnace temperatures and residence times for completion of all of the transformation reactions and pig iron nugget production. The experiments involved the heat treatment of self-reducing?fluxing dried greenballs at various furnace temperatures and residence times. The products of these heat treatments were identified by utilizing optical microscopy, apparent density and microhardness measurements.

Jan 1, 2007

By Wern-ping Chen, Jean Habimana, Jinyuan Liu, Mirza M. Rabbaig, Robert Barbour

To mitigate and control the combined sewer overflows from 17 outfalls in the City of Detroit, three outfalls in Dearborn Heights and eight outfalls in Redford Township, the Detroit Water and Sewerage Department has completed the preliminary design of a storage tunnel in 2005. In 2006, a final design has revised the alignments and the inside diameter (ID) of the tunnel. The revised tunnel system includes an 11.28-km(7-miles) 9.14-m (30-ft) ID tunnel, a 24.4-m (80-ft) ID pump station, two work shafts about 15.2-m (50-ft) ID each, and 14 drop shafts with various IDs. This paper discusses the latest development of this tunnel system.

Jan 1, 2007

By Verya Nasri

The use of a single tunnel boring machine (TBM) tunnel of approximately 12 to 13 m (40 ft to 43 ft) diameter for transit systems to house both light rail or subway tracks in a stacked configuration is an advanced concept that allows significant savings in construction cost and time while reducing, to a large extent, the negative effects on the environment. This solution, similar to the recently completed Barcelona Metro Line 9, integrates station platforms, train storages, crossovers, bypass tracks, ancillary areas and utility corridors inside a single tunnel. Each of the underground stations consist of a cut-and-cover entrance structure and ventilation shafts, that also serve as emergency exits. The excavations for the station structures and shafts can be done on one side of the street with nominal impact on traffic and utilities.

Jan 1, 2010

By Tim Brick, Peter Jewell, Stephen Thompson, Simon Morgan

The $980m (€750m) Dublin Port Tunnel, Europe’s biggest urban highway tunnel project, was opened in December 2006. The culmination of this immense scheme is set to transform the environment, mobility and road safety of Ireland’s capital city. This paper summarizes the key aspects of a project linking both sequential and parallel construction of individual tunnels and describes various approaches to bored, mined and pre-support cut-and-cover tunneling in a wide variety of ground types and depth of cover. Examples of innovative approaches to deal with structural and geotechnical problems while maintaining full operation of both road and rail traffic and the integrity of properties in a dense urban corridor are described.

Jan 1, 2007

By Stephen M. Smading

The Jinping-II hydroelectric project in China features four parallel headrace tunnels approximately 18-km- (11-mile-) long. Two will be excavated by tunnel boring machines (TBM) and two by drill-and-blast. A nearby fifth tunnel is being excavated by a 7.2-m (23.6-ft) TBM to draw down ground water in advance of excavating the headrace tunnels. Unique onsite assembly of a 12.43-m (40.7-ft) main beam TBM and backup system was completed on Sept. 18, 2008 in the remote mountains of the Sichuan province. The equipment was assembled onsite, without previously having been assembled and tested in a factory, using a method called onsite first time assembly (OFTA). This paper addresses the following topics: ? Project description including geology and terrain. ? The decision process leading to onsite, first time assembly, the assembly process and logistics, and lessons learned. ? Design features of the TBM and backup system. ? Operational history from startup to the writing of this article.

Jan 1, 2009

By K. Oraee

Zarshuran gold deposit, with the total reserves of some 12.5 million tons of 4.18 g/ton ore, is considered to be an important gold mining project in the area. In this paper the feasibility studies of the whole project is carried out on the basis of several economic variables. Given that mining data are often of uncertain nature, these economic variables have therefore been estimated under the conditions of uncertainty. The resultant Net Present Value is hence also obtained under the same conditions. For this purpose, a model is first devised with the help of Excel and COMFAR software. The model is then developed that considers different scenarios which would result in different expected values for the economic variables. It is concluded that the NPV of the project is most sensitive to gold and silver price and that other variables such as discount rate, operating and capital cost all affect the feasibility of the project with lower degree of severity. Finally, risk analysis is also carried out using Mont Carlo technique, in order to estimate the most probable value of NPV. The average NPV calculated in this way is US$ 49.7 Million, whilst without due consideration of risk, this would be US$ 36.6 Million. The techniques used, together with the procedures adopted in this paper, can be used in feasibility studies of all mining projects. Such decision would result in more accurate Net Present Values than expected from other frequently used methods.

Jan 1, 2011

By Tony Peglas, Harry Asche, Eva Wood

The North-South Bypass Tunnel is a new $AUD1.5 billion underground traffic route in Queensland, Australia, a project of the Brisbane City Council. The tunnel is approximately 5.2 km long, bypassing the Central Business District, and is adjacent to and below major buildings and services. Road tunnel alignment issues include the complex southern connections to the Pacific Motorway and the design of ramps to the east and the north. A review of road tunnel alignment criteria and accident data for Australian and overseas tunnels, similar to the proposed NSBT, are discussed. The key findings of this review lead to a rationalization of the traditional tunnel cross sectional width allocation. The road alignment design elements adopted for the NSBT are also discussed. The NSBT route crosses beneath the Brisbane River. Geotechnical investigations and hydrogeological modelling are described. The crossing has a fundamental impact on the alignment and the tunnelling methods. The tunnelling methods to be adopted and the tunnel support are described. The geotechnical investigations and hydrogeology analysis culminate in the selection of a single shielded TBM for the reference design. These outcomes are related to complex issues of hydrogeology and contaminated groundwater. These are discussed in detail.

Jan 1, 2005

By D. M. Weinberg, S. R. Novascone, R. R. Reynolds, J. H. Cole, C. D. Christensen

The mechanical properties of the rocks surrounding an orbital vibrator alter the shape and amplitude of the vibrator’s orbit. Detecting these changes with driving point impedance measurements promises to reveal fractures and, possibly, identify the in situ stress state and significantly increase the depth that can be investigated. Our research emphasis has been on detecting vertical fractures through casing. Experimental and numerical results to date indicate that our new logging tool has excellent potential for determining both the vertical extent and azimuthal orientation of such fractures. Fracture and in situ stress orientations are useful in mine planning.

Jan 1, 2002