Search Documents

By S. R. Dindarloo

"Truck-shovel systems are the dominant material loading and haulage machinery in open pit mining operations. Optimal selection, sizing, and allocation of this capital intensive equipment is highly desirable for both achieving production targets and improving the mine’s economics. In this study, discrete event simulation technique was applied for modeling material transportation in Golegohar open pit iron ore mine in Iran. Direct observation of the material loading and haulage for duration of three months resulted in statistical modeling of the operation in the form of probability distribution functions. These probability models were used as the inputs of a stochastic simulation model constructed in GPSS/H simulation language. The model was validated through comparison with the actual operation and was used to test different what-if scenarios and sensitivity analysis of the current system. Some modifications in the number of trucks, shovels, and dispatching strategies were proposed. Simulation resulted in considerable improvements in the mine’s production and economics.INTRODUCTION There are three different mechanisms of discrete, continues, and hybrid material transportation in open mines, including but not limited to: i) in-pit crusher and conveyor belts (hybrid), ii) slurry piping (continues) and iii) truck-shovel system (discrete). Although, each mechanism has its advantages, the truck-shovel system is the dominant method of material loading and handling in open pit mines owing to its high production rate, excellent flexibility, relatively low operating and capital costs, and good maintainability. General objectives of optimal equipment selection include: i) meeting the long and short term requirements of production rates, ii) human & equipment safety, iii) environmental protection, and iv) economic operations (Figure 1).The two most important decision factors on a truck-shovel system selection and sizing are the equipment geometry and size. Geometry (equipment width, weight, turning radius, swing angle, etc.) is mostly controlled by mine’s designs and layouts, as well, as operational constraints. After selection of a favorable geometry based on the constraints; the next step is to select the equipment manufacturer. Once the geometry and manufacturers are selected; the next step is to decide on models (e.g. Bucket size) and required number of each unit"

Jan 1, 2015

By AJIT SWAIN, SUNATI MOHANTY

The abstract discusses the importance of predicting the dewatering performance of industrial hydrocyclones from laboratory models. It highlights the challenge of scaling up design and operating parameters for efficiency estimation. The paper describes experiments with a 2-inch and 4-inch hydrocyclone using silica sand. It details the development of a model using the Nageswararao hydrocyclone model and a simulator to estimate model parameters. The model is validated with experimental data, and a new model is developed using 4-inch hydrocyclone data. The technique is then extended to predict dimensions for a full-scale dewatering cyclone operating at higher throughput and solid concentration.

Mar 30, 2022

By I. H. Douglas

All grade control methods in use currently by the mining industry are imprecise. The methods suffer from being locally inaccurate, leading to are loss and contact dilution. An ore/waste indicator variable can be used to predict the probability of ore occurrence at a given location, Po. Then, an ore grade Zo for an ore location and a waste grade Zw for a waste location are obtained. The expected revenue is calculated at each location, based on its probability of being are or waste, the corresponding grade, and on the cost of mining and processing the ore or the waste. Finally, the decision of whether to recover the block is based on the expected revenue value for that block. The method is illustrated with an example taken from the Jerritt Canyon district in northeastern Nevada.

Jan 1, 1994

By K. F. Unrug

The method of coal pillar design involves primarily two aspects, the geometry of the pillar and the strength of the coal. However, the strength of the coal has to be emphasized with respect to the entire pillar dimension rather than isolated strength values of coal samples taken and measured from different locations. The presently applied pillar design systems do not specify clearly what the coal sample strength really represents. The intention of this paper is to introduce the concept of seam strength as opposed to the current practice of using coal strength as a prime design criteria in the formulation of pillar calculations. Seams are most of ten composed of multiple layers of coal, partings, and bone in different configurations, changing within the vertical section of the seam even in relatively close locations. The difference in strength between the weakest and strongest component of the coal seam could be as much as five times or more. An experimental approach based on multiple compressive tests performed on coal samples from the Coalburg and the Warfield seams from Eastern Kentucky was undertaken. The analysis of the results lead to the conclusion that for pillar calculations both the weighted mean of the seam strength and the strength of the weakest stratum should be considered rather than the relatively vague aspect of coal strength The design of pillar dimensions based on the above mentioned aspects should assure a more realistic design performance.

Jan 1, 1985

By BEN WANG, HAORAN LI, YALI FENG, JINRONG JU

Acidic wastewater is at present directly neutralized with lime or limestone, which wastes resources such as titanium, scandium and iron and generates a great deal of solid waste. This study proposes a novel approach for the separation and recovery of titanium, scandium and iron from acidic wastewater, and utilization of red gypsum. The proposed process not only recovers valuable metals from acidic wastewater but also treats the red gypsum that has previously been dumped.

Aug 1, 2022

By Frederick S. Fisher

Three spatially separate porphyry copper/molybdenum deposits are associated with the Tertiary Needle Creek igneous center in the southern Absaroka Mountains, Wyoming. In all three deposits a central zone containing disseminated copper and molybdenum is surrounded by a halo of small, discontinuous base and precious metal veins. Propylitically and phyllically altered rocks are common in all three mineralized areas, and potassically altered rocks are locally present. Fission- track age data from apatite and zircon indicate that mineralization occurred about 32-40 m.y. ago. Limited data suggest that the lead isotopes are nonradiogenic, similar to porphyry copper deposits elsewhere in the western United States. The complex igneous history of the Needle Creek center has involved several periods of intrusive and probably extrusive activity. lntrusive rocks are calc-alkalic and include andesite, granodiorite, diorite, quartz monzonite, dacite, and rhyodacite. Stocks (1-30 kmz in exposed area), radial dike swarms, and sills make up the presently exposed plutonic masses and constitute lower-level vent fillings in an old stratovolcano. The Needle Creek igneous center is located approximately midway along a northwest-trending belt of intrusive rocks extending more than 100 km along the central axis of the Absaroka volcanic field. The igneous and mineralized centers within this belt were probably localized at the intersections of northwest- trending Laramide and possibly Tertiary fracture systems and earlier northeast-trending Precambrian structures in the underlying basement rocks.

Jan 1, 2013

By Chee Theng

The Mineral & Metallurgical Processing Division (MPD) of the Society for Mining, Metallurgy & Exploration held the 13th MPD Student Poster Contest on March 1, 2023, during the MINEXCHANGE 2023 SME Annual Conference & Expo. The event showcased the work of 24 graduate and undergraduate students from U.S. and international institutions. The contest began in January when the students submitted one‐page abstracts for judging. In February, they prepared and presented posters that explained their research, and each student had five minutes to showcase their research to a panel of judges during the conference. In recognition of their efforts, the MPD provides monetary rewards to all participants. For graduate students, first place receives $1,000, second place $500, and third through seventh places $200 each, and for undergraduate students, first place receives $1,000 and second place $500. The main authors of nonplacing entries receive $125 each. Participation in the contest also includes a free ticket to the MPD Luncheon, where the winners are announced.

Nov 28, 2023

By F. Daviess

A requirement for geological controls during orebody modeling results from the recognition of heterogeneous geological characteristics and/or abrupt variations in orebody geometries. While purely statistical methods are often sufficient for modeling uniform homogeneous deposits, and the only recourse for many that are extremely complex, geological interpretations can be extremely valuable as controls during the modeling process. The advent of relatively inexpensive, sophisticated graphical computer hardware and software has focused considerable attention on the three dimensional visualization capabilities now available to the mining industry. Orebody geometries can be easily imported into many systems as wireframe or solid models, rendered with shading and color, rotated in space, exploded into composite parts, zoomed into and otherwise displayed to awe any audience. The requirements for an initially meaningful, accurate, geological interpretation are sometimes lost when the focus is on an apparently complex, highly resolved end product. Details of the initial data and sensitivities of modeling assumptions are not always sufficiently scrutinized. Software capabilities have extended the geopoetic license into three dimensions. The new tools, while greatly facilitating model construction and rendering, have done little to expedite basic data preparation and analysis. This paper attempts to briefly summarize the purpose and method of the construction of geological controls. The examples selected are from wire­framing and block modeling; application software processes commonly used in the mining industry today.

Jan 1, 1992

By Ehsan Nasiri, Keivan Pak Iman

Historically, boulders are a frequent source of problem in soft ground tunneling. It is important to attempt to make an assessment of the nature and quantity of the boulders, although in many cases, it will be impossible to do so with great accuracy. Boulders, can pose major problems for TBMs in terms of slowing down or halting the tunnel advance, cutter damage, and abrasive wear. Although proper selection of the TBM and the cutterhead can reduce the risks, ground uncertainties still cannot be eliminated. The paper reviews a case study of a 3480 mm diameter EPB-TBM in Toronto utilized for completion of 2.5 km tunnel in Glacial Till, crossing the CP railway, HWY 401, a creek, and a confined aquifer. Alignment consists of multiple horizontal curves including small radius curves (r=210 m) at shafts breakthrough. An unexpected boulder cluster lead the contractor to experience extreme damages to the screw conveyor, RFJ system and causing a crack in main motor plate which resulted in losing one of the six main motors. This paper reviews contractor’s solutions and includes discussion on specific claim resolution method used in this project that can be of great value in preparation of specification and GBR for similar projects.

Jun 13, 2021

By David R. Kalasky

One of the primary areas of computer application in mine ventilation has been the analysis of mine ventilation networks. A variety of network analyzers that are aimed toward the solution of flows in a given network has been developed. These programs typically use the Hardy Cross or other iterative algorithm for solution of any network, even those that are complex. The computer software has become more efficient and sophisticated over time and has thus been widely adopted for ventilation network analysis. One of the shortcomings of these programs is that they have been developed with the idea of analyzing the ventilation requirements at a single point in the lifetime of a mine. This provides the ventilation engineer with an important tool for analysis but falls somewhat short of providing a convenient means to economically com- pare alternative methods for ventilating a mine. The program described in this paper provides such a tool. The principal concepts that were necessary for the completion of a computer program that analyzes ventilation alternatives is the capability of efficiently determining the ventilation requirements at a variety of times during the lifetime of the ventilation system and some method of analyzing the costs of the alternatives on a realistic comparative basis. To accomplish this task, the authors began using Penn State's mine ventilation simulator designated as PSU/MVS, Didyk et al. (1977a, 1977b) and added the necessary additional software to accommodate the need for multi-period, time-dependent analysis of the net- work. The software was then tested on a coal mine ventilation problem with a 23-year life. The problem points out the value of such a program for ventilation analysis.

Jan 1, 1986

By A. Juganda, H. PINHEIRO, J. Brune, N. SANDOVAL, G. Bogin, K. Gallagher, F Wilson

The present work discusses the nuances of scaling and flow similarity to develop a 1/40th scale version of a longwall coal mine. Details on the geometric, kinematic, and dynamic scaling of the physical model are presented and discussed. This works also discusses using a 30% CO2 – 70% He gas mixture as a surrogate for methane. It also presents the implications of various Reynolds numbers (ranging from 7,000 to 140,000) and rotation of the shearer drums in the dynamic representation of the airflow and gas mixtures in the physical scaled model.

Mar 19, 2022

By J. D. Mc Beth

The Carlin Gold Mining Company, a wholly owned subsidiary of Newmont Mining Corporation has been successfully operating an open pit gold mine and cyanide mill for approximately the past ten years. It is a unique operation in that about 20 percent of the mill feed is a carbonaceous ore refractory to cyanidation that must undergo a pretreatment stage developed for, and by, Carlin. The mine and plant are located in the Tuscarora mountain range is north-eastern Nevada near the towns of Carlin and Elko. Claims were staked at the minesite in 1961 and 1962. A drilling program was initiated late in 1962 and after drilling a total of 250,000 feet of rotary drill holes an estimated 9,300,000 tons of ore at a grade of 0.32 ounces of gold per ton was delineated.

Jan 1, 1975

By Bruce H. Mason

Lightweight aggregates are classified as those minerals, natural rock materials, rock-like products, and byproducts of manufacturing processes that are used as bulk fillers in lightweight structural concrete, concrete building blocks, precast structural units, road surfacing materials, plaster aggregates, and insulating fill. Other uses include architectural wall covers, suspended ceilings, soil conditioners, and other agricultural uses (Mason, 1989). One unusual agricultural use recently reported was for bedding on a crocodile farm on the south coast of Natal. It seems that female crocodiles became upset because there was no vermiculite in which to lay their eggs due to the late arrival of a consignment of vermiculite. The vermiculite was being used as a substitute for river sand to nest crocodile eggs (Griffiths, 1989). The various lightweight aggregate materials may be classified into four groups as follows: 1. Natural Lightweight Aggregate Materials-prepared by crushing and sizing natural rock materials, such as pumice, scoria, tuff, breccia, and volcanic cinders. 2. Manufactured Structural Lightweight Aggregates-prepared by pyroprocessing shale, clay, or slate in rotary kilns or on traveling grate sintering machines. 3. Byproduct Lightweight Aggregates-prepared by crushing and sizing foamed and granulated slag, cinders, and coke breeze. This group of lightweight materials, with the exception of slag, has become less significant and will not be discussed in this chapter. Other lightweight aggregates are beginning to appear in the marketplace. Some are the result of manufacturing processes on industrial byproducts and/or waste products, such as fly ash and incinerator residue (Bigner, 1992). 4. Manufactured Insulating Ultralightweight Aggregates-pre- pared by pyroprocessing ground vermiculite, perlite, and diatomite. The application of diatomite in brick and in extruded and aggregate forms has declined in recent years (Kadey, 1983) and will not be considered in this chapter. Lightweight aggregates for structural concrete and concrete masonry units, according to the American Society for Testing and Materials (1986) consist of "aggregates of low density used to produce lightweight concrete, including: pumice, scoria, volcanic cinders, tuff and diatomite; expanded shale, clay, slate, perlite, vermiculite or slag; and end products of coal or coal combustion" (Mason, 1989). Lightweight aggregates are distinguished from other mineral aggregate materials by their lighter unit weights-1 281 to 1 602 kg/m3 or less for loosely packed lightweight aggregates-as com- pared to 2 002 kg/m3 or more for crushed stone, sand, gravel, air-cooled slag, and other common mineral aggregates. The specific gravities of these lightweight aggregates are also used to classify them for use in concrete; they range from the extremely light materials, used for insulative and non-structural concrete to expanded shale, clay, slate, and slags used for structural concrete. Vermiculite and perlite are sometimes referred to as super light- weights. Insulating concrete (non-load bearing) weighing as little as 240 kg/m3 can be made with these aggregates. Natural aggregates such as pumice, pumicite, and scoria are normally made into concrete weighing about 400 to 480 kg/m3. Expanded shale, clay, and slate produced in a rotary kiln make structural concrete ranging from 1 201 to 1 842 kg/m3. Expanded shale and clay produced by sintering make concrete that ranges from 1 442 to 1 922 kg/m3. Air-cooled slag produces concrete ranging from 2 162 to 2 403 kg/m3. The low density lightweight aggregates are used primarily for insulating purposes. They have relatively low compressive strength. The middle density aggregates are used for insulation and for fill. Those at the upper end develop excellent compressive strength and are used in many structural applications (Anon., 1971). In recent years, the production of lightweight aggregates in the United States for all uses (including insulation and construction materials) has averaged about 19 Mtpy (Table 1). The production and consumption of lightweight aggregate is closely tied to the fortunes of the construction industry and the need to construct energy efficient buildings. Recent years have seen the production of lightweight aggregate approach the levels of the early 1970s. The period of 1979 to 1981 was a low point in production levels. The low levels of production were caused by significantly higher plant energy costs due to the large amounts of fuel and energy used in the production of most types of lightweight aggregate. Lower levels of construction activity also affect production levels. This chapter focuses on the use of natural lightweight aggregates and manufactured insulating ultralightweight aggregates, and on both the production and use of manufactured structural light- weight aggregates. Some additional comments are made on byproduct materials. Separate commodity chapters on vermiculite, perlite, pumice, and volcanic cinders are elsewhere in the volume. Discussion of the commodities covered elsewhere in the book will be limited to observations on their utilization and relation to other lightweight aggregate materials.

Jan 1, 1994

By F. J. Bruey

Refdist is a simple but valid approach to planning or analyzing a test-vs-control plant trial that uses accumulated plant performance data to calculate objective criteria for judging the trial outcome. Refdist calculations and results are explained and illustrated with data typical of the mining industry. Findings from a simulation study of Refdist statistical properties are reported. Suggestions for dealing with messy data situations are offered.

Jan 1, 1999

By M. C. Williams

As the flaws in the population balance model (PBM) comminution model are examined more deeply, further errors and problems were discovered. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations was used to solve the dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. The fact that the PBM model equation Inverse Problem is degenerate or underspecified is demonstrated. Multiple solutions to the same PBM equations are provided. It is shown that there is no unique solution to the Inverse Problem unless additional constraints are provided or assumptions are made such as the Arbiter-Bhrany normalization assumption. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution to a dynamic PBM, while giving the same prediction for a given grinding time interval, gives different solutions or predictions for mill composition for other grinding times. Actual experimental grinding data was assessed to determine the functionality of mill selection and breakage functions.

Jan 1, 1993

By B. C. Darst

Developments in the agricultural use of potassium (K) have been based solely on the essential role K plays in crop production. Crop plants cannot complete their normal life cycle if K is deficient or absent. In fact, no essential plant nutrient other than nitrogen is required in greater quantities. Table 1 shows the amounts of K some crops take up from the soil. Although the exact functions of K in the plant are not well known, its primary role seems to be tied to plant metabolism. Potassium is vital to the process of photosynthesis. When K is deficient, photosynthesis declines, but respiration increases. These two K-deficient conditions. . . reduced photosynthesis and increased respiration ... lower the plant's carbohydrate supply, the end result being poor agronomic crop production. Potassium is also essential to several other plant functions, including the following: 1) Protein synthesis. 2) Water use efficiency, through the influence of K on stomata opening and closing, to maintain the turgidity in plant leaf cells. 3) Translocation of heavy metals such as iron and zinc. 4) Ionic balance. 5) Control of enzyme reactions within plants.

Jan 1, 1985

By Klaus Rabensteiner, Klaus Chmelina

"INTRODUCTION Urban tunneling is often related with special geotechnical risks. Typical causes are difficult (hydro)geological conditions, a very low overburden and the presence of critical and vulnerable (infra)structures in the influence zone of the construction (e.g. existing tunnels, roads and pavements, sewer pipes, gas and power lines, landmarked buildings, historic monuments). To manage these risks appropriately, an early detection and warning of unexpected behavior of the affected geotechnical objects ground and tunnel, as well as existing structures are mandatory. To accomplish this, the design and execution of a dense geotechnical monitoring program is of high importance. In more detail, this means specifying and performing a systematic and continuous acquisition, processing and analysis of monitoring data to support decision making. In recent years the development of new automatic sensors and (wireless) data transfer techniques and the general trend towards an automatic acquisition of monitoring data has led to an enormous increase of data production frequencies and volumes. In order to handle this data explosion efficiently, information systems and geo-databases have been developed and used successfully in many projects. They represent IT tools that support the different tasks of a given geotechnical monitoring program including data acquisition, transfer, check, processing, backup, analysis, distribution, reporting and, last but not least, alarming. Meanwhile, some tools already have developed the capability to connect to other theme-specific databases used in the project and, thus, serve as a central data management system for all kind of digital data produced. This makes possible the implementation of further useful functions and services supporting tunneling tasks such as machine control, tunnel simulation, geological prediction, process optimization, etc. where data from different engineering disciplines must be combined and processed in an integrated way. In the following chapters our aim is to describe how monitoring data management, geotechnical monitoring, alarming and reporting are organized and technically implemented at the metro project Cityringen in Copenhagen (Denmark). We want to highlight the specific role and tasks of the used tunnel information system in the project, and particularly inform on the most relevant challenges."

Jan 1, 2016

By M. J. Virnig, C. P. J. Van Vuuren, A. J. Botha

The Zadra, AARL and organic elution processes and variations of them are presently widely used to recover gold from activated carbon. Despite this the study of the kinetics of elution have received relatively little attention. It is the aim of this study to investigate the rate processes taking place during elution in both inorganic and organic solutions. Batch adsorption and elution rate and equilibrium experiments were performed. The spatial concentration of gold inside carbon particles at various stages of the adsorption and elution processes were measured with a scanning electron microscope using an image analyzer to control and manage the micro-analysis data. The activated carbon particles exhibited film and intra-particle mass transfer rate- controlled behaviour during adsorption in a caustic aqueous solution at 95°C. Elutions in the aqueous caustic acetone solution at 30°C and the caustic aqueous solution at 95°C were unaffected by change in stirring rate. Elution was modelled by desorption reaction rate-control at the outer surface of the carbon particle. Adsorption and elution isotherms under duplicated solution conditions showed reasonable agreement for the inorganic solution and a large disparity for the organic solution.

Jan 1, 1993

By Justin R. Patts, Andrew B. Cecala, A. KYLE LOUK, Emily J. Haas

The National Institute for Occupational Safety and Health (NIOSH) and the former U.S. Bureau ofMines (USBM) have given a significant effort over the past four decades in researching and developing engineering controls and interventions to reduce mine workers’ dust exposures during the bagging and palletizing of industrial minerals. Workers performing manual bagging and palletizing of 50- to 100-pound bags typically have some of the highest dust exposures of all workers at mining and mineral processing operations. This paper will provide an overview of available dust control technologies for bagging operations and present the findings of a recent case study that was conducted at four different industrial sand operations to identify the current types of bagging and palletizing technologies being used and to evaluate their effectiveness in reducing workers’ exposures to respirable crystalline silica dust. An evaluation will also be performed to determine if further reductions in respirable dust levels can be achieved by incorporating additional modifications or improvements into the existing technology.

Apr 3, 2020

By Kwangmin Kim, Taehee Lee, Minkyu Kim, JUNHYEOK PARK

Mine tailings storage facilities (TSFs) can be a significant source of fine, respirable dust. About 25 percent of the mass fraction of tailings from a hard-rock mine consists of particles of a respirable size (smaller than 10 μm) [1]. This dust poses concerns, especially for nearby communities, because of its detrimental impact on respiratory health. Respirable tailings dust, primarily composed of quartz or free silica (SiO2), may cause silicosis, chronic pulmonary disease, bronchitis, collagen vascular diseases, and chronic granulomatous infections [2].