Search Documents

By E. B. Graves

I have been asked to talk to you this morning about phosphate marketing and distribution. In discussing this I will attempt to answer such questions as: What is phosphate? Where do we get it? What form is it and how do we sell it? How do we distribute it? How is it applied? And last, but not least, What about the future? To start with, phosphate is one of the three primary plant nutrients. It is the element essential for root structure of plants. Plants, like humans, need a balanced diet. Thus, the amount of phosphate required by individual plants is, in part, related to how much of the other nutrients are used. Virtually all soils contain a certain amount of available phosphates. Back at the turn of the century the most common source of additional plant nutrient, including phosphates, was from cattle manure. The use of chemical fertilizers is something that has grown significantly during the last half century, and in particular, the last 20 years.

Jan 1, 1977

By John C. Draper

[Duquesne Light Company's three power plants in western Pennsylvania are now receiving high BTU clean coal from a new coal preparation plant. When burning coal from this plant, particulate emissions are greatly reduced and the sulfur content of stack ace descend. The cleaner coal also leads to more effecting overall operating of the power plants because of less bulk handling of fuel and ash. Environmental improvement is an important benefit of the cleaner, more complete combustion.]

Jan 1, 1976

By R. Woods, J. D. Wright

INTRODUCTION The Endako deposit was first explored in 1926, but development waited until the early nineteen sixties. It first came under the control of Placer Development in 1963, and early in 1964 a decision to bring it into production was reached. The deposit is located near the geographic center of British Columbia, and is served by an east-west communication system including a paved highway, mainline railway and good telephone, teletype, and computer facilities. The plant area is shown in Figure 1. The operation is known as the Endako Mines Division of Canex Placer Limited of Vancouver. First production was achieved in June, 1965, at a nominal rate of 10,000 tons per day, but it soon was closer to 15,000 tons per day. In 1967, two new grinding and flotation sections brought capacity to the present rate of approximately 27,000 tons per day. With mill heads of around 0.15 percent MoS2, production is about 14,000,000 pounds of molybdenum per year. A flowsheet of the operation is given in Figure 2. A legend for this flowsheet is given in Table 1. Published ore reserves are estimated at 214,500,000 tons at an average grade of 0.143 percent MoS2. PRIMARY CRUSHING The 85 or 100-ton haulage trucks dump over a grizzly into a 42 inch x 65 inch C.A.C. (Canadian Allis Chalmers) gyratory crusher.

Jan 1, 1976

By W. M. Tuddenham

It would be most difficult to place a date on the beginning of the revolution in analytical techniques that we have witnessed in recent years; but there is no question that the period since the end of World War II has seen a major change in thinking with respect to control and accounting analyses. For reasons relating to competition, much of this change was brought about in the chemical industries and only more recently has begun to affect directly the mineral industries. In considering the subject outlined in the title of this paper, one might well be tempted to discuss solely the more exotic methods of control and automation which have come into being in the past short while. In this paper, however, an attempt will be made to take a broader view and consider not only the application of newer purely physical methods of control but also those phases of chemical plus physical analyses that have bearing on our industry.

Jan 1, 1962

By Neall. George M.

No method of roof control yet devised has proven to be universally acceptable for the wide range of strata conditions experienced in U.S. coal mines. However, a relatively new innovation, the roof truss, has proven itself capable of preventing roof failures which both conventional and resin bolting could not. Presently, the economics of roof trusses are not favorable when compared to bolting due primarily to drilling and installation procedures, but this is expected to change with improved truss and equipment designs. To realize the full potential of this new method of roof control, design criteria are needed which can optimize the effect of the truss for varying strata conditions. A review of the literature reveals that some work has been conducted on the roof truss. 1 Gambrell and Haynes (1970) showed that the roof truss is superior to angled roofbolts installed through a header. Sheorey, Verma, and singh2 (1973) used statics to prove that the optimum angle of inclination should be greater than 450? However, to date, no systematic attempt has been made to establish design criteria. In this report, the problem was approached in three ways. First, model studies were performed to determine general trends of truss support as a function of a number of variables. This provided a better understanding of the support mechanism involved. Secondly, beam theory was employed to calculate the actual support capacity of a truss, realizing the many simplifications, assumptions, and shortcomings of this approach to such a complicated problem. Last, field testing will be utilized to test the hypotheses previously developed and provide hard data to further synthesize roof truss design criteria. Field testing has recently commenced and should be complete before mid 1977.

Jan 1, 1977

By Nikhil Dhawan, Veeranjaneyulu Rayapudi, Singh Rahulkumar Sunil

The ever-increasing demand for steel and the subsequent depletion of high-grade ores requires the massive utilization of low-grade iron ores. In the present study, an iron ore slime sample containing 56.1% Fe was investigated using physical beneficiation, carbothermal reduction, and a microwave-assisted process; however, physical beneficiation and microwave exposure were found to be inefficient as they yielded lower iron recovery. Using coconut shell as an alternative reductant was found to be promising and does not lead to the formation of higher iron oxides, such as fayalite and wustite phases. The microwave-assisted carbothermal reduction was found at par with conventional reduction, saving time and heating. The optimum magnetic concentrate obtained in both carbothermal reduction routes (microwave and muffle furnace: Fe grade, Fe recovery, and yield of 64.3, 97, and 84%, and 67, 99, and 83%, respectively) are suitable for alternative iron-making or blast furnace units.

By W. E. Benton

The name Perlite applies to both a hydrated volcanic glass containing from 2% to 5% combined water and to the lightweight material that is produced from expanding the sized volcanic glass. Upon heating, Perlite expands to about twenty times its original volume which results in a material of low density, low thermal conductivity, and high sound absorpt'ion. Perlite ore is mined by open pit methods and is crushed and sized to provide specific gradations for expanding into products used in acoustical tile, built- up roofing, filtration, lightweight concrete and horticultural applications, among others. In 1983, the U.S. production of crude Perlite came from 12 mines and 6 western states, with apparent consumption and production estimated to be about 6% lower than 1982. The average price per ton was slightly higher than in 1982.

Jan 1, 1984

By ANA E. BOHE, MICCO GEORGINA DE, GASTON G. FOUGA, JUAN P. GAVIRIA, FEDERICO J. POMIRO

To the best of our knowledge, this paper comprehensively summarizes a thorough study to determine the thermodynamic viability of the reactions between light rare earth oxides and chlorine with and without carbon. The kinetics and mechanisms of light rare earth oxide chlorination and carbochlorination reactions are analyzed and discussed according to results in the literature. Lanthanides between lanthanum (La) and gadolinium (Gd) are considered as light rare earth elements (LREEs) in agreement with previous literature and the results detailed in this review. Both laboratory- and industrial-scale light rare earth chlorinations and carbochlorinations, starting from oxides and ores, are reviewed.

By D. C. McLean

One of the few innovations in hydrometallurgy in recent years has been the utilization of the chemistry of basic iron sulfates called jarosites. These have been used to make iron-zinc separations in the processing of zinc concentrates and are a very important factor in both the Duval and Cymet copper chloride processes as a means of preventing iron build-up in the closed leaching circuits. Copper oxychlorides are kindred compounds in that they are insoluble basic salts that form at low pH (1.5 to 3) and precipitate selectively from many base metal solutions. They have been reported in the chemical literature as far back as 1860, and a few of them are known in their mineralogical forms (particularly atacamite) usually as nuisance minerals because of their chloride content. Several patents describe their synthesis and use as fungicides and insecticides, and papers have discussed their formation as corrosion pro¬ducts on copper and brass piping (14).

Jan 1, 1979

By T. M. Yegulalp

Geometric programming is a mathematical optimization technique, first formulated by Zener [1], for dealing with certain types of functions which typically arise in engineering design problems. The theory provides algorithms for finding the optimal solution, existence theorems by which one can show that a particular design is possible or not; and characterization theorems that especially make possible to obtain the relationships among the optimal design parameters at optimum. It has been demonstrated [2] that this technique can be applied to several design problems in chemical, electrical and mechanical engineering. Design problems in mining, metallurgical and mineral engineering have many aspects similar to that of other engineering problems. Thus it is only natural to consider geometric programming as a potential tool for solving certain optimization problems in mineral industries.

Jan 1, 1974

By E Marambio, R Brändle, G Fischer, G von Rickenbach, L Burgos, R Luis Fonseca

Ground support systems must provide safe and effective designs for underground excavations under high stress conditions. These systems must be capable to resist dynamic impacts and yielding during the loading process. In this context dynamic testing of the reinforcement and retaining elements that compose the ground support system are required to study and improve the behaviour of these elements under dynamic load events. During the last years, Geobrugg has been working on the improvement of retaining products by testing them in a large-scale impact test facility located at Walenstadt, Switzerland. The test facility is composed of a double level platform with a square-shaped pyramidal trunk geometry, in the upper level housing a loading mass that drop from a height up to 5m. The loading mass is guided by one central steel pipe, and the impact occurs in the sample to be tested located at the lower level in a slab with an area of 3.6m × 3.6m where the ground support system is installed. During the last years, this innovative facility has been used to test several configurations of ground support systems. The results of these tests have enabled to improve the understating of the behaviour of ground support systems under dynamic loads. In this manuscript, the arrangement, measurement, results, and the preliminary analysis of a single impact dynamic test performed during 2021 of a ground support system with a high-tensile steel wire mesh MINAX 80-4.6 is presented.

Apr 26, 2022

By I. Nishkov, L. Alexandrova

The kinetics of froth flotation and the three-phase contact (TPC) parameters are studied at temperatures varying from 20°C to 40°C. The material floated consists of glass spheres and a quartz particles with various diameters. Dodecylamine hydrocloride (DDAHCI) is used as a collector. The equilibrium three-phase contact angle is measured with a microscope technique using the modified Mingins-Scheludko method. Using a Wilhelmy method, the temperature effect on the surface tension of the DDAHCI solution is determined. The formation of the thin film on a polished plate of vitreous silica and the expansion of TPC is monitored by means of a metallographic microscope and recorded on a attached camera at different temperatures. The experimental data show an intensification of the flotation kinetics at 30 and 40°C in the case of small particles. Such an intensification is not observed with the larger particles. The cause for intensification of the flotation kinetics is sought for in the dependence of the TPC rate of expansion and induction time on temperature.

Jan 1, 1995

By EDER DOMINGOS OLIVEIRA, Leandro Viana Teixeira, Carlos Antonio Morais, Ruberlan Gomes Silva

Special attention must be considered in the production of high-grade rare earth products, such as mixed rare earth oxalates or carbonates. In the main minerals used industrially, the rare earth elements (REEs) are finely associated with impurities like calcium (Ca), magnesium (Mg), manganese (Mn), iron (Fe), aluminum (Al), thorium (Th), uranium (U) and phosphorus (P). Most of these impurities must be removed to avoid losses of rare earth oxides (REOs) as well as to prevent product quality degradation and low operational performance in the downstream steps of solvent extraction or ion exchange. The present study aims at investigating the conditions required to precipitate REEs, either as rare earth oxalates or carbonates, from purified rare earth sulfuric liquor with low Al3+ and UO22+ concentrations and very high Ca2+, Mg2+, Mn2+, and SO42− impurity contents.

By W. M. Shaver, R. Letourneau, W. R. Dengler

Dynatec Mining Limited contracted to sink a 1500 metre (4960 ft.) concrete lined shaft for Falconbridge Nickel Mines in Sudbury, Ontario, Canada. The shaft is 6.3 metres (20.5 ft) in diameter inside the concrete lining and is equipped with steel furnishings. Dynatec used the owner supplied 4.6 metre (15 ft.) diameter double-drum hoist to sink the shaft with 12.5 tonne buckets for muck removal and 4 cubic metre concrete buckets for concrete placement. One of the unique features of the shaft sinking operation is the use of a four-boom electric hydraulic drill jumbo permanently mounted in the shaft sinking stage. This paper will describe the performance obtained with the electric hydraulic drilling equipment and the high capacity muck removal and concreting equipment.

Jan 1, 1991

By BHAMIDIPATI S. SASTRY, Pavan Kumar Kattamuri, ADITYA PANDEY

The thermal conductivity of rock surrounding the airway is one of the most important thermal properties for estimating strata heat transfer into the mine air and for designing the air-cooling strategies. Several laboratory methods are available for the determination of thermal conductivity; however, most of them are complex and cumbersome. The present study explains the working principle of Lee’s apparatus which is relatively simple, easy to fabricate and use, and provides consistent results. In the present study, thermal conductivities of sandstone cores obtained from an Indian coal mine are determined using Lee’s apparatus. An approach is discussed for determining the temperature gradient of sandstone specimens while cooling and used for calculating thermal conductivity. The thermal conductivity of different sandstone specimens attains values between 2.37 and 2.59 W m− 1 °C−1. For different sandstone cores obtained from the field, properties including specific gravity, specific heat capacity, thermal diffusivity, and porosity, along with thermal conductivity, are determined and highlighted in this study.

Jul 20, 2021

By Fathi Habashi

THE MOST important arsenic minerals are shown in Table 6-1. The recovery of arsenic from arsenic sulfides is treated in Chapter Four. Arsenical ores may be either leached directly, or first smelted to volatilize as much arsenic and sulfur as possible, and the resulting product, called speiss, is then leached. A speiss is mainly a complex mixture of metal arsenides, but its [Table 6-1. Arsenic minerals. Arsenides Niccolite NiS Smaltite CoAs2 Skutterudite CoAs3 Sulfarsenides Cobaltite CoAsS Enargite CuaAsS4 Arsenopyrite FeAsS Arsenic sulfides Realgar As4S4 Orpiment As2S3] composition varies widely, depending on the type of ore treated. A speiss usually contains 15-35% arsenic. Methods of leaching are describedd in the following paragraphs.

Jan 1, 1970

By BARBOSA AMILTON, Denise C. R. Espinosa, David B. Dreisinger

Chelating resins can be used to recover important metals from different sources, and it is important to understand which resin is most suitable for each metal [1]. This review  benefits the mining industry because chelating resins can be used to recover metals from low-grade ores and mining tailings, increasing the industrial process efficiency [2–4]. Furthermore, the use of chelating resins in mining processes and mining tailings has the common problem of metals contamination, with iron being the main contaminant in low-grade ores and tailings. Understanding how contaminants decrease ion exchange efficiency is significant for industries [5

By Abhilash, S. Sarkar, T. Venugopalan, P. Meshram

"To explore blast furnace slag as a secondary resource for rare earth elements (REEs), blast furnace slag containing lanthanum (La), cerium (Ce), erbium (Er) and neodymium (Nd) in concentrations of 17, 16, 4 and 44 ppm, respectively, was processed with sulfuric acid while optimizing the parameters of acid concentration, temperature and pulp density. The experiments showed that recovery rates of 92, 36, 35 and 52 percent for La, Ce, Nd and Er, respectively, were achieved at 1 to 5 weight/volume (w/v) percent pulp density using particles smaller than 250 µm and treating with 1 M sulfuric acid for one hour at room temperature. Raising the temperature to 95 °C promoted the dissolutions of Ce and Nd to 89 and 84 percent, respectively, for the same 1 M acid concentration and one-hour duration at 5 w/v percent pulp density. Cyanex 923 was preferred over Cyanex 301 for the purification of REEs from leach liquor. In another route, the leach liquor was subjected to precipitation with 0.5 to 1 M oxalic acid, resulting in a product with 4 to 5 percent concentration of REEs.IntroductionRare earth elements (REEs) are important materials in numerous high-technology applications, but they have high supply risk, giving rise to the study of new sources. The recycling of REEs has been well researched, especially on a small scale, but has not been widely implemented. Less than 1 percent of REEs were recycled in 2011 (Binnemans et al., 2013). REEs occur in a large number of minerals in oxidic compounds, such as oxides, carbonates, phosphates and silicates, and are present as mixtures at 10 to 300 mg/kg concentrations in many rock formations, such as basalts, granites, gneisses, shales and silicate rocks. The most abundant REE in the Earth’s crust is cerium (Ce), at a concentration of 20 to 70 mg/kg, followed by neodymium (Nd) and lanthanum (La), with heavier REEs being less abundant (Binnemans et al., 2013). REEs occur in nature in their oxidized forms in salts and minerals due to their electropositive nature and high affinity for oxygen. The possibility of recovering REEs"

Jan 1, 2017

By David M. MacGillivray

1. INTRODUCTION The economic importance of bringing a new mine to production in the shortest possible time, is well known. In recent years the rate of escalation of mining costs has accelerated more rapidly than at any time in the past. This fact has enhanced the need to reduce time schedules and made it an overriding and predominant objective when planning new shafts. The squeezed profit margins and widely fluctuating metal prices have also increased the emphasis being placed on this aspect. Moreover the increase in the present value of future profits due to the reduction in the time element, can be so substantial that expenditure on equipment and additional labour can be justified conditional on sufficient gain in shaft sinking speed being achieved. The emphasis on time saving becomes more abundantly clear when considering the very large increase in the capital required to bring a modern underground mine to production. As an example, the initial capital expenditure requirements for a large new gold mine in the Western Transvaal, which has commenced production recently, is estimated at R200M, and a major extension to another deep level mine in the same area is estimated at R300M. With the uncertainty of future metal prices and the recent trends in increasing inflation, it is becoming more difficult than ever to estimate the profitability of proposed mining projects and any cost saving due to more rapid sinking of shafts can only assist in this respect. Since the shaft systems are frequently the most expensive set of underground excavations and no other underground work can commence until they are completed, the speed of shaft sinking is subject to closer scrutiny than in the past. In the following sections of this paper the factors contributing to the high average advance rates achieved by South African shaft sinkers are discussed. It is difficult, if not impossible, to estimate the effect of any single factor, in isolation, on the overall sinking achievements. However, the cumulative effect of improvements made in the inter-related activities is, probably, the most important contributor. Although there has not been any single major technical change or innovation to shaft sinking practices in the last decade, the average sinking speeds have increased, due to improved application and technical improvements in established procedures. 2. GENERAL When discussing South African shaft sinking techniques and average sinking rates compared to those achieved in other parts of the world, it should be remembered that the size and depth of South African shafts are often considerably greater than in most other countries. Typical examples of shafts either in the course of sinking or recently completed are -

Jan 1, 1979

By M. C. Williams

The solution of the dynamic population balance model (PBM) of a closed grinding network consisting of a mill, sump, and cyclone is problematic. The fact that the dynamic PBM model equation solution to the Inverse Problem for grinding systems is degenerate or underspecified is demonstrated. Two numerical solution approaches to the Inverse Problem are used. These are: 1) providing additional constraints on breakage selection functions or 2) performing the Arbiter-Bhrany (or other) normalization of the selection functions. Actual experimental anthracite batch grinding data is used to demonstrate the non-unique functionality of the batch dynamic mill selection and breakage functions for a real physical system. The Levenberg-Marquardt algorithm for systems of constrained non-linear equations is used to solve the batch dynamic PBM grinding equations to obtain the grinding selection and breakage rate functions. Different solutions to the same PBM transport equations are provided. The mill, sump and hydrocyclone were modeled as a CSTR operating at various retention times. Batch dynamic PBM data was used to provide the mill kinetic and breakage selection function data. Two different solutions were obtained depending on the numerical solution approach. The severity of the non-uniqueness problem for dynamic grinding is demonstrated. Each solution approach to a dynamic PBM with transport, while giving the same prediction for a single batch grinding time, gives different solutions or predictions for mill composition for other grinding times. This fact makes dynamic nodal analysis and control problematic. The fact that the constraint solution approach gives a solution may suggest that normalization for closed networks is not necessary. Differences in solutions to the PBM cannot be excused away by inaccuracies in the data used to model the grinding phenomenon.

Jan 1, 1995