Search Documents

By Welby G. Courtney

Recent field and laboratory results related to the use of water sprays and ventilation in the control of dust at the mine face are presented. Optimization of water sprays for impaction and collection of airborne dust is discussed and guidelines presented. Exhausting versus blowing primary ventilation, dust collectors, several secondary exhaust ventilation systems, and a "throw" technique he discussed.

Jan 1, 1980

By Husheng Li, Zhongli Wu

This paper discusses the fundamental strategies adopted in the simulation package FIRES developed for ventilation simulation under mine fires. These fundamental strategies include (1) fire characteristic curves specifying the development of a mine fire with time, (2) simulation of fume spread in a ventilation system, (3) determination of the aerodynamic effects of mine fires on flows; and (4) dynamic simulation of flow state under mine fires. The major functions of the simulation package are also addressed. The package has been used to simulate an experiment of mine fire. A comparison is made between the simulation results and the measured data.

Jan 1, 1993

By A. M. Gaudin

The recent study by R. M. Hays(l) prompted the study summarized in this paper. In his Interesting paper, Mr. Hays shows fine results to be attainable by a relatively complex flowsheet on a semi-taconite, a manifestly difficult ore to treat. We obtained a semi -taconite from Minnesota, and treated this sample by wet magnetic separation alone. The device in which the separation was accomplished is the standard pilot-plant, laboratory separator in use at Magnetic Engineering Associates' laboratory (MEA) in Cambridge, Massachusetts. It consists of a cylindrical space which can be magnetized by turning on the magnet of the separator. In this cylindrical space, there is a canister which provides the special configuration of the magnetic field and magnetic field gradients that MEA considers to be required. The ore pulp is made to flow through the canister while the current is on. A portion of the pulp is retained in the canister, and the rest is evolved as a non-magnetic fraction. The laboratory device is cyclic, but it accurately predicts the results obtainable by an Industrial unit of either cyclic or continuous type (moving matrix). The ore tested was 99.5°%o -325 mesh, and approximately 75% -500 mesh. The concentrate from this ore was, therefore, eminently suitable for pelletizing. In passing the ore through the magnet, we had the choice of repeatedly passing the concentrate from the first step through the operation, or of repeatedly passing the non-magnetics. In our experiments, the first method was clearly superior from the stand¬point of the cleanliness of concentrate. Of the many tests which we have made, we think that we have to retain two which

Jan 1, 1971

By D. C. Sisti

A paper was presented during the 1970 SME Fall Meeting on the Stinson Preparation Facilities by representatives of Beaver Creek Consolidated Cool Company and Heyl & Patterson, Inc. This paper summarized a combined approach to development of a flow diagram and selection of cleaning equipment required to produce a uniform metallurgical coal at maximum recovery with special emphasis on sulphur reduction. These facilities were located in the Elkhorn. Coal Fields of eastern Kentucky and, in particular, the area of Wayland, Knott County, Kentucky, where approximately forty-five- million tons of Elkhorn No. 3 coal could he recovered. The facilities incorporated a Bradford Breaker for reduction of the ROM coal to minus 1-1/2 x 0, 6000 ton-raw coal storage, preparation plant, water clarification and thermal drying facilities, clean coal storage and a 4000 TPH unit train loading facility.

Jan 1, 1973

By Saul Escalara

Data on sulfonate adsorption by silicate minerals are very scarce in the literatures. Perhaps the only comprehensive paper written on the topic was done by Fuerstenau and Bhappu (1); this work dealt exclusively with quartz but included many important suggestions as to the form and nature of the hydroxy-sulfonate species of some cations formed during the conditioning step and their effect on the flotation response of quartz. Another paper by the same authors (2) contains additional data on the role of hydrolysis in sulfonate flotation of beryl. As postulated by Fuerstenau and Bhappu, a solid form of cationic sulfonate functions as the collecting species to produce flotation of quartz and beryl. According to the authors, the solid compound is a hydroxy-sulfonate of a given cation, where the hydrogen of the hydroxyl part provides a means for bonding of the species to the mineral surface; thus, the presence of hydroxyl in the neutral precipitated compound is of primary importance to produce flotation. Although the preceding examples illustrate the effect of a sulfonate collector in silicate systems other than plagioclases, they are important as examples of processes of hydroxy-sulfonate complex formation. Since the plagioclase minerals con¬tain Ca(II) and Al(III) cations, which are very reactive in sulfonate media (1), the formation of hydroxy-sulfonate compounds with these cations released from the solid phase may well prove to be the cause for their flotation.

Jan 1, 1973

By G. Raspa

This article describes a procedure for calculating the recoverable reserves of stratified orebodies characterised by a thin and irregular layers. An application on the phosphate deposits in the N'Zeto region of the Popular Republic of Angola is also described. The procedure consists in building a block model of the deposit through the conditioned multivarial geostatistical simulation of small areal units. The recoverable reserves are then calculated and defined by applying to the model a selection processes based on measured geological/economic parameters taken from the drillholes: thickness of overburden and mineralised layers, economic grain-size fraction, grade. The procedure also takes account both of the geometrical constraints of the mining method and dilution. For reasons of confidentiality, a multiplier has been applied to the values adopted for the sampling data.

Jan 1, 1992

What is your assessment of the mining industry as we near the end of the 20th century? As it always has, the industry is continually changing. The recent rate of change has been hectic. Many mining-related commodities are selling at low prices. These include gold, silver, copper, coal and soda ash, to name a few. Lower prices place pres- sure on mining companies to increase efficiency through productivity, down- sizing or mergers. The short- term effect of this situation may adversely affect the individual SME member. But the long- term benefit is to build a stronger, more productive and internationally competitive mining industry. In addition, most of these metals and minerals have been historically cyclical in nature, and prices will rebound.

Jan 1, 1999

By Bonn J. Macy, David A. Gulley, William A. Vogely

INTRODUCTION Some of the most famous and graphic environmental incidents have arisen from mineral extraction, including oil spills, the Reserve Mining asbestos tailings case, Kaiparowitts surface mining and coal combustion, and other environmental causes celebre. The remote location of much of the mining industry to some extent reduces the human health hazards from pollution, but often times the pristine locale in which mining is conducted provides a sharp contrast to the impacting industry. This prompts questions as to what the research literature says about the true costs and benefits of environmental compliance. We survey the state of this knowledge. Where possible, we discuss studies focused on mining and related industries, such as primary metals production. In many cases, how- ever, the studies pertain to the economy as a whole. For present purposes, the mining industry is defined as companies engaged in the production and refinement of minerals, including metals, fuels, and nonmetallics (e.g., phosphate, sand and gravel). There are several stages in mining, with environmental effects occuring at every stage. The exploration stage comprises the period from initial prospecting to the point where the deposit has been located and delineated in sufficient detail to permit development decisions to be made. Geophysical and geochemical surveys, diamond drilling programs, and exploratory stripping and excavation are activities that may be employed during this stage. Some forms of prospecting are relatively benign, al- though even airborne surveys and motor vehicles generate noise pollution. Roads and the passage of vehicles and equipment affect land surfaces and vegetation, and attract heavier backcountry use. Clearings, stream crossings, and borrow pits can lead to increased erosion and sedimentation of streams. Geological survey grids disrupt vegetation and appearance. Moreover, prospecting can involve the excavation and stripping of overburden, resulting in soil and vegetation disruption as well as in- creased sedimentation of streams and lakes. The effects of exploration are often temporary, and frequently less severe than for other activities. Nevertheless, exploration-related impacts vary with the intensity and type of exploration effort, and can be significant. During the development stage of mining, shafts are sunk, pits excavated, buildings erected, and transportation facilities established. Dust, noise, and other socioeconomic and environmental impacts are generated by the relatively large and sudden influx of people, equipment, and activity. Surface disturbance and solid waste are generated by development, and liquid wastes form when mines are dewatered. The extraction phase is associated with a variety of environmental impacts. These impacts may differ for surface and underground mines. In surface mining, surface disturbance is obviously a major consequence. Piles of overburden and waste accumulation mar land surfaces. Wind and water erosion tend to spread the dis-

Jan 1, 1985

By A. K. Mukhopadhyay, B. Sikdar, V. P. Arora

Introduction During the past several years, persistent concerns about an economic slowdown in India have tempered capital-expan¬sion plans. This has encouraged companies to find methods of increasing the capacity of existing production equipment. One of the more cost-effective methods of increasing produc¬tion capacity without major capital investment is to improve equipment maintenance to prevent needless machine down¬time. This can have a significant financial impact because of reduced maintenance costs and increased machine availabil¬ity. The maintenance program employs different techniques, but the analysis of the vibration behavior of machine compo¬nents to assess their condition was found to be the most accurate technique for monitoring various machine disorders. A dragline that handles overburden in open pit mines is one of the more capital-intensive pieces of production equip¬ment. It is imperative that the machine be run at its optimum capacity under the prevailing environmental conditions. Condition monitoring of the various components of the dragline through vibration analysis not only improves the machines availability but also ensures a long operation time free from sudden failure. This paper describes the application of vibration monitor¬ing and analysis techniques to assess the components of a W2000 dragline. The paper reveals that condition monitoring through vibration analysis can be as valuable in failure prevention as it is in failure analysis. Finally, the paper presents an approach to a knowledge-based expert system to the quick and correct diagnosis of mechanical faults in a dragline. Equipment A dragline is an intermittent-discharge-type excavator having a long boom at one end. Unlike other excavators, the bucket is not rigidly held by the frame structure. In favorable geomining conditions, the intensive operation of these exca¬vators is the least-expensive means of overburden removal. The basic working elements of this equipment are the hoist system, the crowd and retract system, the wing mechanism and the propel mechanism. The walking dragline is accepted as the most economical machine for stripping overburden at depths of up to 60 m (200 ft). They are electrically powered and the various motions are effected by individual drives. The Ward-Leonard system is used to provide the optimum flexibility in controlling different dc-drive motors. To mini¬mize the cost of mineral extraction, the largest such machine in India has a 24-m3 (850-cu ft) bucket with a boom length of 96 m (315 ft). Draglines are very costly, and considerable financial penal¬ties may arise from sudden stoppages due to component fail¬ures. Thus, operational reliability is of the greatest importance. Active measures are now being taken to minimize downtime by adopting condition-based maintenance techniques. Though a number of techniques come under this scheme, it has been observed that assessing the health of the dragline by measuring vibration is the best method of determining the dynamic behavior of its various rotating components to avoid any catastrophic failure. Based on criticality, the vibration-behav¬ior of the following components are studied: • motor-generator unit, • exciter unit, • hoist motor-gearbox unit, • hoist drum-gearbox unit, • drag motor-gearbox unit, • drag drum-gearbox unit and • swing motor unit The approach Increases in the vibration levels in different subsystems of the dragline were observed due to the presence of faults such as unbalance, misalignment, looseness and bad bearings. A vibration behavior study included the measurement of vibra¬tion level, trend analysis of time-domain vibration signals and vibration frequency analysis at bearing points of the components. A vibration meter, a vibration analyzer and a data collector are used. Vibration-level measurement. When the dragline was assembled and put into operation for the first time, vibration data were collected to generate baseline data for the equip¬ment (based on International Standard ISO 2372). After¬wards, the vibration levels were recorded regularly using a vibration meter. The measurements were taken at all bearing

Jan 1, 2000

By T. Glenn Pobanz

For more than fifty years Walter Kidde & Company, Inc. has engaged in the development and manufacturing of both fire suppression and detection equipment. Our initial work for the mining industry centered around dry chemical extinguish-ing equipment for mine haulage cars. To fulfill this need, Kidde engineered and developed a manually activated dry chemical system to provide protection for the wheel wells, cable reels, and motor compartments on various pieces of underground mining equipment. The next phase of mining operation fire protection for Kidde was the area of detection and automatic fire suppression for conveyor belt heads. Early in 1970, a field evaluation program and belt head demonstration unit was taken to 10 areas throughout West Virginia, Kentucky, Pennsylvania, and Ohio. This extensive field program was a joint effort with National Mine Service Company of Pittsburgh, Pennsylvania. The objectives of this program were to study mine hazard problems and to determine further requirements of mine operators. The resulting belt head detection system centered around our Continuous Strip Thermistor Core heat detector in conjunction with a Kidde stored pressure dry chemical extinguishing system. Continuous Strip detection has been in use for a number of years in aerospace applications. It has proven flexible and reliable for the rapid detection of overheat conditions and fires in engines of over half the aircraft flying today. The use of Continuous Strip gave us flexibility to protect surface areas over and around the actual conveyor belt head equipment. The nature of Continuous Strip allows us to bend, wrap, and attach the 20 foot long thermistor element over the desired protected points of the belt head. An integral part of the conveyor belt head protection system is the control panel utilizing our comprehensive knowledge of fire alarm control logic. This panel contains supervision circuits which sound trouble signals upon detecting a break in the Continuous Strip; breaks in the wiring to the remote electrical extinguishing activators or to the alarm bell; or loss of primary power. A separate control module provides the adjustable alarm temperature setting of the

Jan 1, 1971

By C. Y. Chen

In order to put an end to the uneven environmental standards and enforcement established by various coal mining States in the United States, the Congress passed and the President signed the Surface Mining Control and Reclamation Act (Public Law 95-87 or the Act) on August 3, 1977. Within one year after passage, the Secretary of the Interior was directed to promulgate permanent program regulations implementing Title V provisions of the Act. These regulations were to form the basis for State regulatory programs under the Act and to allow States to assume primary regulatory responsibility. In order to implement the underground mining provision of the Act, the Secretary is directed in section 516(a) of the Act to promulgate rules, but ones which take into consideration the distinct differences between surface coal mining and underground coal mining. The regulations developed by the Secretary and promulgated on March 13, 1979, with respect to subsidence control, included (1) a subsidence control plan as part of the permitting process, (2) substantive provisions establishing performance standards for subsidence control, and (3) provisions providing for the prohibition of mining under perennial streams, impoundments larger than 20 acre feet, and certain public facilities and urban areas.

Jan 1, 1985

By F. Letowski

A column reactor was applied for leaching with simultaneous flotation a complex sulfide ore in ferric sulfate-solution under oxygen pressure. Elemental sulfur and the flotable, nonreacted sulfides were collected in the froth and separated from the insoluble, nonflotable gangue minerals and solid particles formed during pressure leaching. The two-stage laboratory unit, built from Corning-glass elements is described. Results of the continuous leaching/flotation experiments conducted under 20-40 psig of oxygen pressure are presented, as are supplementary batch leaching experiments with iron precipitation under 150 psig oxygen pressure. High zinc extraction to solution and near total accumulation of lead sulfate in the nonflotable fraction are easily attainable. Relatively poor flotation of pyrite is probably caused by the partial oxidation of its sulfidic sulfur to sulfate.

Jan 1, 1988

By Robin P. Gardner

The mechanistic or phenomenological approach to ball milling involving the, concepts of particulate selection and breakage functions with particle population balance models has been well established over the past decade (c.f., the review articles by Austin (1) Herbst and Mika, (2) and Snow (3)). Initial efforts to apply this approach concentrated on batch milling, but since most milling in industrial practice is continuous, much recent research has been directed to extending this approach to continuous milling. The primary difference between batch and continuous milling processes is the relative importance of material mixing and transport in the mill in the latter case. Much analytical (4-8) and some experimental (9-15) work on the effect of mill mixing and transport on milling has been recently reported. Much of the analytical work has naturally centered around extension of the well-developed concepts that have been applied to chemical reactors, (16-18) Fortunately, it has been found(1) that most milling processes are analogous to first-order chemical reactions so that the combined effects of material transport and reaction (breakage) can be handled by the relatively simple segregated flow concepts. (8)

Jan 1, 1973

By J. S. Jaspal

Mining of thin coal seams is both difficult and uneconomical. As a result, most of thin-seam coal reserves in the U. S. are not being mined. It is estimated that nearly 910 Gt (K. Unrug, 1985) of coal reserves exist in 355 to 710 mm thick seams. The Bureau is attempting to develop new techniques for mining 150 to 1065 mm thick coal seams. This paper summarizes the research work on existing thin-seam mining techniques, testing on small and full scale physical models of the Bureau slot mining concept, and computer modeling of the full-scale process.

Jan 1, 1992

By David S. Smith

Almost nine years after the assertion of enormous and pervasive federal control over coal mines by means of the Federal Coal Mine Safety and Health Act of 1969, 30 USC Section 801 et seq, as amended by the Federal Mine Safety and Health Act of 1977 (which basically increases the punitive powers of government) a brief assessment of some of the underlying causes, present status, and possible alternatives to governmental control is appropriate. In a governmental system based upon the principles of democracy and the protection of individual freedoms and constitutional rights the ultimate mechanism for abrogation of these rights is the creation and exploitation of fear. Machiavelli in rendering advice concerning the power over men provided by fear stated, "... it is much safer to be feared than loved .. fear preserves (the government) by a dread of punishment which never fails." The Prince. Within the context of the assumption of control by the government over industries or segments of our population - popular fear provides a convenient and almost necessary mechanism for the avoidance by law or regulation of democratic principles. The popular fear of coal mines has been successfully exploited by various goal oriented groups in the past and most recently by a Congressional constituency with a vested interest in controlling the mines through regulation.

Jan 1, 1979

By M. Rosenshine, R. W. Barbaro

This paper presents a cyclic queueing model that evaluates the productivity of a shovel-truck materials haulage system. For a cyclic queueing problem with exponentially distributed service times, a cyclic queueing model provides exact solutions in a fraction of the time that simulation takes to produce an approximate solution. The model is applied to an example problem, and the results are validated with simulation. Simulation is used to show that the assumption of exponentially distributed service times and steady state are not serious problems. A cyclic queueing model can be used to quickly obtain an accurate assessment of the productivity of a shovel-truck system.

Jan 1, 1988

By A. W. Hamilton

If you don't know a gauss from a grasshopper, you may be better off than you, think, particularly if you're an ore dressing engineer charged with the responsibility of selecting magnetic equipment for minerals separation and beneficiation. Gauss is a unit of measure for a magnetic field. It indicates the number of imaginary lines of force per square centimeter or per square inch radiating from a magnet. In discussing the strength characteristics of a magnet, we have come to speak of a magnetic field of 800 gauss, for example, meaning 800 lines of force per square centimeter. Gauss became the standard for selecting drum type separators many years ago under an arbitrary set of circumstances. The standard has continued to this day even though magnetics applications engineers have long considered it inadequate. The configurations of the older gauss meter were such that the most accurate and convenient readings on a drum type separator could be made at distances greater than one inch. So, an arbitrary distance of two inches was established and that two inches became the standard. Since then, it has become commonplace to specify magnetic strengths for drum separators according to average gauss readings at two inches; for example 500 gauss average at two inches, 750 gauss average at two inches and so on, even though gauss readings at two inches have much less to do with the separating and beneficiating function of a given application than was formerly believed. The standard was adopted as a means of gauging the strengths of electromagnetic drum type separators, for they were the only ones around at the time. These machines were usually designed with no magnetic considerations other than that the material to be separated should be agitated vigorously and the magnetic fields should be deep and strong. Drums built this way performed well enough, so it seemed logical to measure their magnetic strengths. Hence, gauss at two inches. Now, new improvements in magnetic techniques have made average gauss measurements at 2 inches positively obsolete.

Jan 1, 1971

By Carlos Viramontes Aldana

Mining in Mexico is one of its post traditional activities, whose influence in the development of important cities and communications has been decisive. Precious metals and, to some extent, copper and tin were known and used before the Colonial period, but from the sixteenth century to tie end of the nineteenth century, mining and metallurgical industries were concentrated in the precious metals, mainly silver. This silver was exported to Spain and other countries under the Spanish. Rule, Mexican peso was known world wide since the end of the sixteenth century and Mexico ranked as the first silver producer since the eighteenth century.

Jan 1, 1985

By Huang Kong Xuan, Li Yun Teng

Reviewing the development of resin-in-pulp (RIP) technology for the extraction of gold in the world, especially in South Africa and USSR, and the chemistry of interaction between aurocyanide ions and anion-exchange resins. RIP benchtest and pilot plant investigations show that the resin of the weak-base and strong-base can absorb gold in the cyanide pulp and gold can be eluted from the strong-base resin by electro-elution. The possibility of future application of RIP technology in China fa also briefly discussed.

Jan 1, 1998

By M. C. Roberts

The material composition of product is defined as the quantity of metal used per unit of product manufactured during a year. The material composition of product has shown steady and persistent declines over time for most metals and materials. This tendency demonstrates the continued improvements in manufacturing technology resulting from substitutions of other materials and increases in production efficiency. The purpose of this paper is to use the material composition of product to show the impact of advanced materials on the use of traditional metals.

Jan 1, 1992